This is my LCD:

The backlight is working upon turning on OPi One.

The official Orange Pi One H3 manual suggests using fbtft_device kernel module, which is LONG deprecated and no longer supported.

On Raspberry Pi forums, someone was suggested to use a Device Tree Overlay  instead.

I've stumbled upon an Orange Pi Zero overlay file for my LCD. So I've changed a few lines:

/dts-v1/;
/plugin/;

/ {
	compatible = "allwinner,sun8i-h3";

	fragment@0 {
		target = <&spi1>;
		__overlay__ {
			status = "okay";

			spidev@0{
				status = "disabled";
			};

			spidev@1{
				status = "disabled";
			};
		};
	};

	fragment@1 {
		target = <&pio>;
		__overlay__ {
			opiz_display_pins: opiz_display_pins {
                pins = "PA9", "PA6";
                function = "gpio_out";
			};
		};
	};

	fragment@2 {
		target = <&spi1>;
		__overlay__ {
			/* needed to avoid dtc warning */
			#address-cells = <1>;
			#size-cells = <0>;

			opizdisplay: opiz-display@0{
				compatible = "philips,pcd8544";
				reg = <0>;
				pinctrl-names = "default";
				pinctrl-0 = <&opiz_display_pins>;

				spi-max-frequency = <400000>;
				fps = <30>;
				buswidth = <8>;
				reset-gpios = <&pio 0 33 1>;
				dc-gpios = <&pio 0 7 0>;
			};
		};
	};
};

And compiled, loaded it into an DTS user directory.

I've connected Arduino as a Serial-to-USB convertor to OPi and it would seem it has loaded successfully:

Applying user provided DT overlay nokia5110opizero.dtbo
4185 bytes read in 14 ms (291 KiB/s)
Applying kernel provided DT fixup script (sun8i-h3-fixup.scr)
## Executing script at 45000000
Kernel image @ 0x42000000 [ 0x000000 - 0xa0ea90 ]
## Loading init Ramdisk from Legacy Image at 43400000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    17670074 Bytes = 16.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 43000000
   Booting using the fdt blob at 0x43000000
Working FDT set to 43000000
   Loading Ramdisk to 48f26000, end 49ffffba ... OK
   Loading Device Tree to 48eb5000, end 48f25fff ... OK
Working FDT set to 48eb5000

But according to armbianmonitor -u output , the overlay ends up creating new errors:

[    1.630221] sun8i-h3-pinctrl 1c20800.pinctrl: pin PA14 already requested by 1c28c00.serial; cannot claim for 1c69000.spi
[    1.630250] sun8i-h3-pinctrl 1c20800.pinctrl: error -EINVAL: pin-14 (1c69000.spi)
[    1.630269] sun8i-h3-pinctrl 1c20800.pinctrl: error -EINVAL: could not request pin 14 (PA14) from group PA14 on device 1c20800.pinctrl
[    1.630288] sun6i-spi 1c69000.spi: Error applying setting, reverse things back

I know the overlay is for Zero series, but i figured it should be the same since H3 is mentioned in there. Or at least I would be glad to know how to modify this for my board.

Attached below are both logs for Serial and the kernel.

So far my goal is display anything, even a black square, on the screen. Would be sick to use it as a screen for console (like /dev/fb0).

Hoping for your help since I'm stuck. Thanks in advance!

dmesg.txt serial.txt

Please note that my primary Armbian PiHole DNS does not encounter the same issue, though the version of it is Noble v25.2.3 / 6.12.30. 

One project consist just on PiHole, the other one on Tailscale.

Since with newer kernel I have high temperature on idle (like 70°C) can you advice me an old version that maybe has a "better" thermal management?
Thank you so much, if I'm saying something stupid please tell me, maybe I just need to tune something like disable hdmi, gpu etc...

I’m trying to get a 3.5-inch RPi display with the XPT2046 touch controller (480x320 resolution) to work on my Orange Pi One (H3). I’ve been looking for guides, but most of them are Raspberry Pi-specific and not directly applicable to the Orange Pi.

Here’s what I’ve tried so far:

• Installed Armbian on the Orange Pi One.
• Connected the display via the SPI interface.
• Installed fbtft and tried different configurations for the screen.

However, I haven’t been able to get the display to show anything or to interact with the touch input.

Does anyone have experience using this specific setup?

• What drivers or overlays should I use?
• Do I need to modify the dtb or dts files?
• Any tips on configuring SPI and touch input in Armbian?

Any help would be greatly appreciated! Thanks in advance.

I have confirmed that the display has power because it turns on.

Ive setup ssh and did some stuff on my OrangePi, when i came back and plugged my phone into power hub my OrangePi was connected to, it restarted and stopped at disk manager, i restarted it and it gave lots of failed messages, i restarted and it didnt work anymore :(

it only gives yellow ethernet led and nothing else, i also reflashed sd card because it got all partitions gone after that incident

Please help!!!

Is it a new feather?

Here are the steps to reproduce the problem. I've done this on "Orange Pi One" board, but exactly the same issue occurs on (community maintained) Banana Pi M1.

1. Download and write the Armbian image to a MicroSD card.

2. Connect the serial console, boot the board, finish setup, do all the upgrades: everything works fine at this point.

3. Set "verbosity=7" in the "armbianEnv.txt", reboot and observe the kernel messages. At this point, the "linux-image-current-sunxi", version 24.5.1 (kernel 6.6.31) is installed.

4. Install "armbian-config" and use it to switch to "linux-image-legacy-sunxi=24.2.1 (6.1.77)". Observe that the board boots up fine.

5. Now switch to "linux-image-legacy-sunxi=24.5.1 (6.1.92)". The boot process now gets stuck at "Starting kernel ..." message.

So as a summary:

*  "linux-image-current-sunxi" version 24.5.1 with 6.6.31 kernel: boots fine.

*  "linux-image-legacy-sunxi" version 24.2.1 with "6.1.77" kernel: boots fine.

*  "linux-image-legacy-sunxi" version 24.5.1 with "6.1.92" kernel: broken: stuck at "Starting kernel ..." message.

I wonder if anyone could check what could have happened with "linux-image-legacy-sunxi" in the latest Armbian build.

Probably similar issue on this thread -

I'm a bit of a noob, if someone can redirect me to pasting logs. Can those be found on /var/logs as I haven't explored much.  I have downgraded both my OPiOnes to 23.11.1 and Frozen the Armbian firmware updates, so I can't provide logs for now at least until I try to update one of the instances.

I‘m recently updated to Armbian 24.2.1 Bookworm with Linux 6.6.16-current-sunxi.

The system is running fine but if I disconnect the network interface, the system gets stuck in kind of a dead loop.
This behavior gave me the hint that my WiFi repeater is broken and needs to be exchanged. Anyway, the CPU temperature rises and no further interaction with the system is possible.

If I disconnect it, from a normal operating switch, the OpiOne’s behavior looks the same.

My problem with this behavior is that after reconnecting the network, it does not get back available, until I do a power cycle.

I tried to read out the root of that problem out of the logs but didn’t had success yet.

I have uploaded the monitor logs:

https://paste.armbian.com/cuqayiyimi
 

Further information: A cooler is attached to the CPU and my PSU is able to provide 6A current.

I haven’t had a problem with this Orange Pi during the last 4 years of running an older outdated version of Armbian.

I’m only running some docker container with only use minimum resources.

I hope that this isn’t a duplicate, haven’t found other topics like that.

best regards

kai

unattended-upgrades-dpkg.log:3:E:Sub-process /usr/lib/armbian/armbian-live-patch apt returned an error code (127), E:Failure running script /usr/lib/armbian/armbian-live-patch apt
unattended-upgrades.log:7:2024-04-11 11:00:58,211 ERROR Installing the upgrades failed!

I have a  local repos for debian and armbian, and the Orange pi-s have no internet access.

Has been working fine in the past years

Did a fresh install having internet access : ok

Armbian_24.2.1_Orangepione_bookworm_current_6.6.16.img.xz

then changed to offline, using my local repos

as example tried to install ntp and docker.io

All failed, with above like errors

So,

Q1 : is it no longer possible to work offline using local repos ?

Q2 : Or is there a work around for this ?

Set

I am new to all this and I have downloaded everything to my sd card.

When I power on the board it gets stuck on "started update UTMP about system runlevel changes" and does nothing more.

some images at https://imgur.com/92ZOiwD

Now that the camera interface has been merged in mainline Kernel, I would like to try to use the OrangePi OV5640 camera module on my OrangePi One.

So with the latest Armbian Bionic (20.02.1, kernel 5.4.20), I have been trying to get a device tree overlay.

But for now, it fails to compile with:

$ sudo armbian-add-overlay sun8i-h3-csi.dts 
Compiling the overlay
Error: sun8i-h3-csi.dts:27.23-24 syntax error
FATAL ERROR: Unable to parse input tree
Error compiling the overlay

My current overlay looks like this:

/dts-v1/;
/plugin/;

/ {
	compatible = "allwinner,sun8i-h3";

	fragment@0 {
		target = <&pio>;
		__overlay__ {
			csi_mclk_pin: csi-mclk-pin {
				pins = "PE1";
				function = "csi";
			};
		};
	};

	fragment@1 {
		target = <&i2c2>;
		__overlay__ {
			status = "okay";

			ov5640: camera@3c {
				compatible = "ovti,ov5640";
				reg = <0x3c>;
				pinctrl-names = "default";
				pinctrl-0 = <&csi_mclk_pin>;
				clocks = <&ccu CLK_CSI_MCLK>;
				clock-names = "xclk";

				AVDD-supply = <&reg_aldo1>;
				DOVDD-supply = <&reg_dldo3>;
				DVDD-supply = <&reg_eldo3>;
				reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */
				powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */

				port {
					ov5640_ep: endpoint {
						remote-endpoint = <&csi_ep>;
						bus-width = <8>;
						data-shift = <2>; /* lines 9:2 are used */
						hsync-active = <1>; /* Active high */
						vsync-active = <0>; /* Active low */
						data-active = <1>;  /* Active high */
						pclk-sample = <1>;  /* Rising */
					};
				};
			};
		};
	};
	
	fragment@2 {
		target = <&csi>;
		__overlay__ {
			status = "okay";
			
			port {
				csi_ep: endpoint {
					remote-endpoint = <&ov5640_ep>;
					bus-width = <8>;
					hsync-active = <1>; /* Active high */
					vsync-active = <0>; /* Active low */
					data-active = <1>;  /* Active high */
					pclk-sample = <1>;  /* Rising */
				};
			};
		};
	};
};

So the line 27, which seem to trigger the error is: `clocks = <&ccu CLK_CSI_MCLK>;`

Also, according to the documentation, the regulator fields are required but this board does not have much regulators (like AXP209), so I have no idea what to write here.

But this is my first time writing a device-tree overlay so I am not sure what is wrong with this line.

Could someone guide me to get my overlay right?

And, does anyone already got the CSI interface working with OV5460 sensor on a H3 based board?

Thank you.

I am trying to get an OV5640 camera working on the orangePiOne. I found this thread

and was wondering if the overlay (or some overlay) is still required.

Without anything extra, the camera is not detected. It says that sun6i-csi and ov5640 kernel modules should be loaded, so I loaded them manually with modprobe but nothing happens and nothing is shown in dmesg.

Adding the mentioned overlay with  "sudo armbian-add-overlay csi-ov5640.dts" just gives me an error in dmesg at reboot time

"failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND

Error applying DT overlays, restoring original DT"

uname -a

Linux orangepione2 6.1.63-current-sunxi #1 SMP Mon Nov 20 10:52:19 UTC 2023 armv7l GNU/Linux

boot logs on https://paste.armbian.com/unoqesepov

wondering what to try next...

bruno@orangepione:~$ sudo cat /sys/kernel/debug/gpio
[sudo] password for bruno:
gpiochip0: GPIOs 0-223, parent: platform/1c20800.pinctrl, 1c20800.pinctrl:
 gpio-15  (                    |orangepi:red:status ) out lo
 gpio-166 (                    |cd                  ) in  lo ACTIVE LOW
 gpio-204 (                    |usb0_id_det         ) in  lo IRQ

gpiochip1: GPIOs 352-383, parent: platform/1f02c00.pinctrl, 1f02c00.pinctrl:
 gpio-354 (                    |usb0-vbus           ) out lo
 gpio-355 (                    |sw4                 ) in  hi IRQ ACTIVE LOW
 gpio-358 (                    |vdd-cpux            ) out hi
 gpio-362 (                    |orangepi:green:pwr  ) out hi
 

Looks like no power on usb0, which should be enabled in host mode

I enabled in armbian-config hardware configuration usbhost 0 to 4 (shows in armbianEnv.txt )

I edited sun8i-h3-orangepi-one.dtb so that usb0 dr_mode is set to "host" (like shown here https://forum.armbian.com/topic/4814-orange-pi-one-usb-otg/?do=findComment&comment=44756 )

I perused this thread https://forum.armbian.com/topic/8686-orange-pi-lite-using-micro-usb-otg-as-host-for-usb-camera/ and verified handles and setting seem to match.

Seems no matter what, usb0 is not powered. 

What am I missing ?

Any help greatly appreciated...

sun8i-h3-orangepi-one.dtb sun8i-h3-orangepi-one.dts

in lieu of a better place on the internet, I just wanted to document that the i2s overlay found here: https://gist.github.com/zuigon/65bfb73bb8a3f971774f80d3e2954adb works flawlessly with Armbian 23.08.0-trunk Bookworm with bleeding edge Linux 6.4.2-sunxi.

after executing the script my PCM 5102 DAC works like a charm.

Im not sure is it because of new build system or the problem is in 6.1.15 kernel branch.

My compile command was:

./compile.sh BOARD=orangepione BRANCH=current BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_ONLY=yes KERNEL_CONFIGURE=no COMPRESS_OUTPUTIMAGE=sha,img SKIP_EXTERNAL_TOOLCHAINS=no BUILD_KSRC=no PRIVATE_CCACHE=yes RELEASE=bionic ARTIFACT_IGNORE_CACHE=yes BUILD_KSRC=yes KERNEL_GIT=full

While installing i got:

igor@honeypot:~/trash/debs$ ls -1
armbian-config_23.05.0-trunk_all.deb
armbian-firmware_1-SA56ad-Bf566_all.deb
linux-dtb-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb
linux-headers-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb
linux-image-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb
linux-u-boot-orangepione-current_2022.07-Se092-P12e0-Be261_armhf.deb
igor@honeypot:~/trash/debs$ sudo dpkg -i *
[sudo] password for igor:             
(Reading database ... 107907 files and directories currently installed.)
Preparing to unpack armbian-config_23.05.0-trunk_all.deb ...
Unpacking armbian-config (23.05.0-trunk) over (23.02.0-82) ...
dpkg: warning: downgrading armbian-firmware from 23.02.0-82 to 1-SA56ad-Bf566
Preparing to unpack armbian-firmware_1-SA56ad-Bf566_all.deb ...
Unpacking armbian-firmware (1-SA56ad-Bf566) over (23.02.0-82) ...
dpkg: warning: downgrading linux-dtb-current-sunxi from 23.02.0-82 to 6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8
Preparing to unpack linux-dtb-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb ...
Armbian 'linux-dtb-current-sunxi' for '6.1.15-sunxi': 'preinst' starting.
+ rm -rf /boot/dtb
+ rm -rf /boot/dtb-6.1.15-sunxi
+ set +x
Armbian 'linux-dtb-current-sunxi' for '6.1.15-sunxi': 'preinst' finishing.
Unpacking linux-dtb-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) over (23.02.0-82) ...
dpkg: warning: downgrading linux-headers-current-sunxi from 23.02.0-82 to 6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8
Preparing to unpack linux-headers-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb ...
Armbian 'linux-headers-current-sunxi' for '6.1.15-sunxi': 'preinst' starting.
+ [[ -d /usr/src/linux-headers-6.1.15-sunxi ]]
+ set +x
Armbian 'linux-headers-current-sunxi' for '6.1.15-sunxi': 'preinst' finishing.
Unpacking linux-headers-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) over (23.02.0-82) ...
dpkg: warning: downgrading linux-image-current-sunxi from 23.02.0-82 to 6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8
Preparing to unpack linux-image-current-sunxi_6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8_armhf.deb ...
Armbian 'linux-image-current-sunxi' for '6.1.15-sunxi': 'preinst' starting.
+ export 'DEB_MAINT_PARAMS=upgrade 23.02.0-82 6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8'
+ DEB_MAINT_PARAMS='upgrade 23.02.0-82 6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8'
+ export INITRD=Yes
+ INITRD=Yes
+ test -d /etc/kernel/preinst.d
+ run-parts --arg=6.1.15-sunxi --arg=/boot/vmlinuz-6.1.15-sunxi /etc/kernel/preinst.d
update-initramfs: Deleting /boot/initrd.img-5.15.93-sunxi
Removing obsolete file uInitrd-5.15.93-sunxi
+ mountpoint -q /boot
+ set +x
Armbian 'linux-image-current-sunxi' for '6.1.15-sunxi': 'preinst' finishing.
Unpacking linux-image-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) over (23.02.0-82) ...
Preparing to unpack linux-u-boot-orangepione-current_2022.07-Se092-P12e0-Be261_armhf.deb ...
Unpacking linux-u-boot-orangepione-current (2022.07-Se092-P12e0-Be261) over (23.02.0-82) ...
Setting up armbian-config (23.05.0-trunk) ...
Setting up armbian-firmware (1-SA56ad-Bf566) ...
Setting up linux-dtb-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) ...
Armbian 'linux-dtb-current-sunxi' for '6.1.15-sunxi': 'postinst' starting.
+ cd /boot
+ ln -sfT dtb-6.1.15-sunxi dtb
+ set +x
Armbian 'linux-dtb-current-sunxi' for '6.1.15-sunxi': 'postinst' finishing.
Setting up linux-headers-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) ...
Armbian 'linux-headers-current-sunxi' for '6.1.15-sunxi': 'postinst' starting.
+ cd /usr/src/linux-headers-6.1.15-sunxi
++ grep -c processor /proc/cpuinfo
+ NCPU=4
+ echo 'Compiling kernel-headers tools (6.1.15-sunxi) using 4 CPUs - please wait ...'
Compiling kernel-headers tools (6.1.15-sunxi) using 4 CPUs - please wait ...
+ yes ''
+ make ARCH=arm oldconfig
  HOSTCC  scripts/basic/fixdep
  HOSTCC  scripts/kconfig/conf.o
  HOSTCC  scripts/kconfig/confdata.o
  HOSTCC  scripts/kconfig/expr.o
  LEX     scripts/kconfig/lexer.lex.c
  YACC    scripts/kconfig/parser.tab.[ch]
  HOSTCC  scripts/kconfig/lexer.lex.o
  HOSTCC  scripts/kconfig/menu.o
  HOSTCC  scripts/kconfig/parser.tab.o
  HOSTCC  scripts/kconfig/preprocess.o
  HOSTCC  scripts/kconfig/symbol.o
  HOSTCC  scripts/kconfig/util.o
  HOSTLD  scripts/kconfig/conf
#
# configuration written to .config
#
+ make ARCH=arm -j4 scripts
  SYNC    include/config/auto.conf.cmd
  HOSTCC  scripts/dtc/dtc.o
  HOSTCC  scripts/dtc/flattree.o
  HOSTCC  scripts/dtc/fstree.o
  HOSTCC  scripts/dtc/data.o
  HOSTCC  scripts/dtc/livetree.o
  HOSTCC  scripts/dtc/treesource.o
  HOSTCC  scripts/dtc/srcpos.o
  HOSTCC  scripts/dtc/checks.o
  HOSTCC  scripts/dtc/util.o
  LEX     scripts/dtc/dtc-lexer.lex.c
  YACC    scripts/dtc/dtc-parser.tab.[ch]
  HOSTCC  scripts/dtc/libfdt/fdt.o
  HOSTCC  scripts/dtc/libfdt/fdt_ro.o
  HOSTCC  scripts/dtc/libfdt/fdt_wip.o
  HOSTCC  scripts/dtc/libfdt/fdt_sw.o
  HOSTCC  scripts/dtc/libfdt/fdt_rw.o
  HOSTCC  scripts/dtc/libfdt/fdt_strerror.o
  HOSTCC  scripts/dtc/libfdt/fdt_empty_tree.o
  HOSTCC  scripts/dtc/libfdt/fdt_addresses.o
  HOSTCC  scripts/dtc/libfdt/fdt_overlay.o
  HOSTCC  scripts/dtc/fdtoverlay.o
  HOSTCC  scripts/dtc/dtc-lexer.lex.o
  HOSTCC  scripts/dtc/dtc-parser.tab.o
  HOSTLD  scripts/dtc/fdtoverlay
  HOSTLD  scripts/dtc/dtc
  HOSTCC  scripts/bin2c
  HOSTCC  scripts/kallsyms
  HOSTCC  scripts/recordmcount
  HOSTCC  scripts/selinux/genheaders/genheaders
  HOSTCC  scripts/selinux/mdp/mdp
  HOSTCC  scripts/sorttable
  HOSTCC  scripts/asn1_compiler
  HOSTCC  scripts/insert-sys-cert
+ make ARCH=arm -j4 M=scripts/mod/
  CC      scripts/mod/empty.o
  HOSTCC  scripts/mod/mk_elfconfig
  CC      scripts/mod/devicetable-offsets.s
  UPD     scripts/mod/devicetable-offsets.h
  MKELF   scripts/mod/elfconfig.h
  HOSTCC  scripts/mod/modpost.o
  HOSTCC  scripts/mod/sumversion.o
  HOSTCC  scripts/mod/file2alias.o
  HOSTLD  scripts/mod/modpost
  MODPOST scripts/mod/Module.symvers
+ make ARCH=arm -j4 tools/objtool
  DESCEND objtool
  HOSTCC  /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/fixdep.o
  HOSTLD  /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/fixdep-in.o
  LINK    /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/fixdep
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/weak.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/check.o
  MKDIR   /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/arch/arm/
  LD      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/arch/arm/objtool-in.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/special.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/exec-cmd.o
check.c:11:10: fatal error: arch/elf.h: No such file or directory
   11 | #include <arch/elf.h>
      |          ^~~~~~~~~~~~
compilation terminated.
make[3]: *** [/usr/src/linux-headers-6.1.15-sunxi/tools/build/Makefile.build:97: /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/check.o] Error 1
make[3]: *** Waiting for unfinished jobs....
special.c:14:10: fatal error: arch/special.h: No such file or directory
   14 | #include <arch/special.h>
      |          ^~~~~~~~~~~~~~~~
compilation terminated.
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/help.o
make[3]: *** [/usr/src/linux-headers-6.1.15-sunxi/tools/build/Makefile.build:97: /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/special.o] Error 1
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/pager.o
make[2]: *** [Makefile:54: /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/objtool-in.o] Error 2
make[2]: *** Waiting for unfinished jobs....
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/parse-options.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/run-command.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/sigchain.o
  CC      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/subcmd-config.o
  LD      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/libsubcmd-in.o
  AR      /usr/src/linux-headers-6.1.15-sunxi/tools/objtool/libsubcmd.a
make[1]: *** [Makefile:73: objtool] Error 2
make: *** [Makefile:1437: tools/objtool] Error 2
dpkg: error processing package linux-headers-current-sunxi (--install):
 installed linux-headers-current-sunxi package post-installation script subprocess returned error exit status 2
Setting up linux-image-current-sunxi (6.1.15-S4261-D4dc8-Pd2ed-C54bbHfe66-Bd6b8) ...
Armbian 'linux-image-current-sunxi' for '6.1.15-sunxi': 'postinst' starting.
+ export 'DEB_MAINT_PARAMS=configure 23.02.0-82'
+ DEB_MAINT_PARAMS='configure 23.02.0-82'
+ export INITRD=Yes
+ INITRD=Yes
+ test -d /etc/kernel/postinst.d
+ run-parts --arg=6.1.15-sunxi --arg=/boot/vmlinuz-6.1.15-sunxi /etc/kernel/postinst.d
update-initramfs: Generating /boot/initrd.img-6.1.15-sunxi
update-initramfs: Converting to u-boot format
+ echo 'Armbian: update last-installed kernel symlink to '\''zImage'\''...'
Armbian: update last-installed kernel symlink to 'zImage'...
+ ln -sfv vmlinuz-6.1.15-sunxi /boot/zImage
'/boot/zImage' -> 'vmlinuz-6.1.15-sunxi'
+ touch /boot/.next
+ set +x
Armbian 'linux-image-current-sunxi' for '6.1.15-sunxi': 'postinst' finishing.
Setting up linux-u-boot-orangepione-current (2022.07-Se092-P12e0-Be261) ...
Errors were encountered while processing:
 linux-headers-current-sunxi

my awus036acm adapter is not recognised , when i type iwconfig it's say no wireless extension

is there possible way to make it work?