AndyW

Tested "Armbian_23.09_Starfive2_lunar_current_6.1.31_xfce_desktop.img.xz" and it works well. Video appears to be a bit better as I can play back a 720p video, though not full 720p size. Sound is still great on HDMI and crackly on the jack.
 
Did you want feedback on which programs work/don't work?
 
 
__ ___ _ _____ _ ____ \ \ / (_)___(_) ___ _ __ | ___(_)_ _____|___ \ \ \ / /| / __| |/ _ \| '_ \| |_ | \ \ / / _ \ __) | \ V / | \__ \ | (_) | | | | _| | |\ V / __// __/ \_/ |_|___/_|\___/|_| |_|_| |_| \_/ \___|_____| Welcome to Armbian 23.09 Lunar with Linux 6.1.31-star64 No end-user support: built from trunk System load: 44% Up time: 5 min Memory usage: 5% of 7.72G IP: 192.168.2.164 CPU temp: 39°C Usage of /: 8% of 58G [ General system configuration (beta): armbian-config ] Last login: Sun Sep 24 16:58:11 EDT 2023 on ttyS0 root@starfive2:~# neofetch root@starfive2 -------------- ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ OS: Armbian (23.09) riscv64 ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ Host: StarFive VisionFive V2 __¦¦ ¦¦__ Kernel: 6.1.31-star64 __¦¦ ¦¦¦¦¦¦¦¦¦¦¦ ¦¦__ Uptime: 6 mins __¦¦ ¦¦ ¦¦ ¦¦__ Packages: 1514 (dpkg) __¦¦ ¦¦ ¦¦ ¦¦__ Shell: bash 5.2.15 __¦¦ ¦¦ ¦¦ ¦¦__ Resolution: 1920x1080 __¦¦ ¦¦¦¦¦¦¦¦¦¦¦¦¦ ¦¦__ Terminal: /dev/ttyS0 __¦¦ ¦¦ ¦¦ ¦¦__ CPU: (4) @ 1.500GHz __¦¦ ¦¦ ¦¦ ¦¦__ Memory: 425MiB / 7908MiB __¦¦ ¦¦ ¦¦ ¦¦__ __¦¦ ¦¦__ ¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ root@starfive2:~#  

@balbes150 Tried the above but it didn't work for me. As per your instructions above I:
- Changed firmware to 3.6.1
- Burned SD card with "reset-default-env-uboot-visionfive2-3.6.1.img" and booted, then turned device off. Attached file "boot-reset-default.txt" shows this. 
- Burned SD card with "update_uboot-visionfive2-3.6.1.img" and booted, then turned device off. Attached file "boot-update-uboot.txt" shows this
- Booted again (stopped autoboot by hitting key) and did a "printenv" so you can see if the changes above worked, then turned device off. Attached file "boot-printenv.txt" shows this
- Burned SD card with "Armbian_23.09_Starfive2_lunar_edge_6.6.0.img.xz" and booted, which failed. Attached file "boot-lunar_edge_6.6.0-failed.txt" shows this
 
So, had a look at the "printenv" output and found nothing "runs" your new env variables "boot_mmc_new", "boot_emmc_new", or "boot_nvme_new"!
 
I also noticed that in the failed boot log the message "## Error: "boot2" not defined". So I booted again, stopped autoboot, did a "setenv boot2 run boot_mmc_new", then "env save", booted again and it worked! Attached file "boot-lunar_edge_6.6.0-worked.txt" shows this.
 
I don't think this is the correct way to "fix" this issue, but it works.
 
Let me know if I did something wrong.
 
 
boot-reset-default.txt boot-update-uboot.txt boot-printenv.txt boot-lunar_edge_6.6.0-failed.txt boot-lunar_edge_6.6.0-worked.txt