January 16, 20224 yr Hello everyone! I bought Khadas VIM1 board and Official FAN(Ali Link) but seems to be not working with Armbian Bullseye, how I can run it? Thanks.
January 16, 20224 yr 41 minutes ago, noisyislands said: I bought Khadas VIM1 board Which revision of board you have? https://www.armbian.com/khadas-vim1/ To be able to boot Armbian SD card image and ...
January 16, 20224 yr @noisyislands have you tried start fan manually by sysfs interface. by default fan will be start at cpu temp 85C
January 17, 20224 yr Author 20 hours ago, Igor said: Which revision of board you have? https://www.armbian.com/khadas-vim1/ To be able to boot Armbian SD card image and ... It is 1.4 Revision Version 13 hours ago, ning said: @noisyislands have you tried start fan manually by sysfs interface. by default fan will be start at cpu temp 85C Oh, 85C it's to much. I don't sure is it here ls /sys/fs/cgroup cgroup.controllers cgroup.procs cgroup.threads cpu.stat init.scope memory.stat sys-kernel-config.mount user.slice cgroup.max.depth cgroup.stat cpuset.cpus.effective dev-hugepages.mount io.stat proc-sys-fs-binfmt_misc.mount sys-kernel-debug.mount cgroup.max.descendants cgroup.subtree_control cpuset.mems.effective dev-mqueue.mount memory.numa_stat sys-fs-fuse-connections.mount system.slice ls /sys/class backlight chromeos drm hidraw ieee80211 mdio_bus net ptp rtc sas_phy sound tpm vc wakeup bdi devcoredump extcon hnae input mem pci_bus pwm sas_device sas_port spi_master tpmrm vfio watchdog block devfreq firmware hwmon iommu misc phy rc sas_end_device scsi_device spi_slave tty video4linux zram-control bluetooth devlink gpio i2c-adapter leds mmc_host power_supply regulator sas_expander scsi_disk tee udc virtio-ports bsg dma graphics i2c-dev lirc mtd pps rfkill sas_host scsi_host thermal usb_role vtconsole Sorry for the late response, I am able to post here only once per 24h UPDI've found thermal devices and their current state is 0, how can I configure it? ls /sys/class/thermal/ cooling_device0 cooling_device1 thermal_zone0
January 17, 20224 yr 8 minutes ago, noisyislands said: It is 1.4 Revision Version This revision we have in our smoke test rig. Check once again and proceed with steps written on Khadas VIM1 download pages (i reflash my VIM1 to eMMC yesterday). Also try alternative method by downloading Krescue (for VIM1) and removing eMMC content similar as described here. 8 minutes ago, noisyislands said: Sorry for the late response, I am able to post here only once per 24h We are forced to limit speed of end users questions, because our ability to support is extremely limited.This way you can unlock it at once and help a bit.
January 17, 20224 yr Author 8 minutes ago, Igor said: This revision we have in our smoke test rig. Check once again and proceed with steps written on Khadas VIM1 download pages (i reflash my VIM1 to eMMC yesterday). Also try alternative method by downloading Krescue (for VIM1) and removing eMMC content similar as described here. We are forced to limit speed of end users questions, because our ability to support is extremely limited.This way you can unlock it at once and help a bit. I've installed Armbian from SD card to eMMC. Seems to be my Fan not working(Fan hardware issue) or thermal configuration sets is too high-temperature level(85C as ning says)
April 20, 20224 yr @noisyislands I found this script for fan control https://github.com/hyphop/khadas-utils/blob/master/utils/fan
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.