OS : Armbian 25.11.2 stable 6.1.115-vendor-rk35xx (Debian trixie)

Overlays : rock-5a-spi-nor-flash

SPI Flash is on /dev/mtdblock0

Boot from SD : OK

Boot from SD system on NVMe : OK

----
 

I want to boot from Flash, so I tried `Install/Update the bootloader on MTD Flash` menu on `armbian-config'.

Then I got this message.

No SPI image found.

I also updated SPI with `rsetup` from Radxa OS, but it does not work(boot from NVMe failed) either.

What do I have to do?

First look through dts i cannot find any problem. Maybe someone has a better understanding?

Thanks
Jakob

I have experimented with a Realtek USB 2.5Gbe USB Ethernet dongle and find that it works fine with the vendor kernel but not with kernels 6.12.x or 6.18.y. 

I have included an iperf3 example below, you can see that the dongle manages a few runs at high speed before it quietly fails and seizes up.

I use a number of these dongles and they tend to work fine on other set-ups.

Any thoughts about a resolution?

 

dmesg output:

[Tue Mar 17 11:37:00 2026] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[Tue Mar 17 11:37:00 2026] usb 2-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=31.00
[Tue Mar 17 11:37:00 2026] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[Tue Mar 17 11:37:00 2026] usb 2-1: Product: USB 10/100/1G/2.5G LAN
[Tue Mar 17 11:37:00 2026] usb 2-1: Manufacturer: Realtek
[Tue Mar 17 11:37:00 2026] usb 2-1: SerialNumber: 0013000001
[Tue Mar 17 11:37:00 2026] usbcore: registered new device driver r8152-cfgselector
[Tue Mar 17 11:37:00 2026] r8152-cfgselector 2-1: reset SuperSpeed USB device number 2 using xhci-hcd
[Tue Mar 17 11:37:01 2026] r8152 2-1:1.0 eth0: v1.12.13
[Tue Mar 17 11:37:01 2026] usbcore: registered new interface driver r8152
[Tue Mar 17 11:37:01 2026] usbcore: registered new interface driver cdc_ether
[Tue Mar 17 11:37:01 2026] usbcore: registered new interface driver cdc_ncm
[Tue Mar 17 11:37:01 2026] usbcore: registered new interface driver cdc_wdm
[Tue Mar 17 11:37:01 2026] usbcore: registered new interface driver cdc_mbim
[Tue Mar 17 11:37:01 2026] r8152 2-1:1.0 enx00e04c680142: renamed from eth0
[Tue Mar 17 11:37:02 2026] xhci-hcd xhci-hcd.3.auto: WARN: HC couldn't access mem fast enough for slot 1 ep 6
[Tue Mar 17 11:37:02 2026] r8152 2-1:1.0 enx00e04c680142: intr status -63
[Tue Mar 17 11:37:07 2026] xhci-hcd xhci-hcd.3.auto: WARN: HC couldn't access mem fast enough for slot 1 ep 6
[Tue Mar 17 11:37:07 2026] r8152 2-1:1.0 enx00e04c680142: intr status -63
[Tue Mar 17 11:37:35 2026] xhci-hcd xhci-hcd.3.auto: WARN: HC couldn't access mem fast enough for slot 1 ep 6
[Tue Mar 17 11:37:35 2026] r8152 2-1:1.0 enx00e04c680142: intr status -63

Subsequent iperf3 example:
iperf3 -c nx1
Connecting to host nx1, port 5201
[  5] local 192.168.1.191 port 58598 connected to 192.168.1.14 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   221 MBytes  1.85 Gbits/sec    0   5.35 MBytes       
[  5]   1.00-2.00   sec   280 MBytes  2.35 Gbits/sec    0   5.35 MBytes       
[  5]   2.00-3.00   sec   280 MBytes  2.35 Gbits/sec    0   5.35 MBytes       
[  5]   3.00-4.00   sec  18.1 MBytes   152 Mbits/sec    1   1.41 KBytes       
[  5]   4.00-5.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
[  5]   5.00-6.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
[  5]   6.00-7.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
[  5]   7.00-8.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
[  5]   8.00-9.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
[  5]   9.00-10.00  sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec   800 MBytes   670 Mbits/sec    1            sender
[  5]   0.00-10.86  sec   796 MBytes   615 Mbits/sec                  receiver

When using all 8 cores, the system overheats (>110 degrees) and eventually shuts down.  For example, when compiling ffmpeg, it works fine with 'make -j6', but 'make -j8' results in a shutdown before compilation is complete.  Likewise I had thermal issues when using llama.cpp.

Shouldn't the OS throttle the CPU when temperature reaches high levels?  I think that is not happening at the moment. Online search referred me to cpufrequtils to set a conservative governor, but it looks like cpufrequtils does not exist for Trixie.

Any suggestions on how I should approach this?

I dd the Armbian_25.11.1_Rock-5c_trixie_current_6.12.58_minimal.img to a SD card (/dev/sdc) and then run a
fsck -f /dev/sdc1 and got errors:
sudo fsck -f /dev/sdc1
fsck from util-linux 2.39.3
e2fsck 1.47.0 (5-Feb-2023)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Entry '.' in ??? (1065) is duplicate '.' entry.
Fix<y>? 
....

Tried few SD cards, same result.
Tried those SD cards with other images, i.e. Armbian_24.8.4_Rock-5c_bookworm_vendor_6.1.75_minimal.img
no problems.
Could anybody verify this behavior?

Thanks
Chris

Armbian_25.11.1_Rock-5c_trixie_vendor_6.1.115_minimal.img image generates the same problem.

Installed Armbian_25.11.1_Rock-5c_trixie_current_6.12.58_minimal.img and one of the USB-3 port, the top one, doesn't work. No reaction when inserting something, nothing in /var/log/syslog. 

The same with Armbian_25.11.1_Rock-5c_noble_current_6.12.58_minimal.img
The Armbian_25.11.1_Rock-5c_trixie_vendor_6.1.115_minimal.img however is OK.

What could be the cause of this problem?

Thanks and regards,

Chris

I am looking for a low power, fanless, solution for a Debian server with a single large 3.5" SATA drive.

I don't want to boot from the SATA so I guess I'd buy an eMMC module as well.

Currently I have an Orange Pi4 LTS with a weird expansion board and a generic Mini PCIe to SATA, but it isn't stable enough.

Given that the Rock 5C has platinum support and works with the Penta SATA hat I'm wondering if it might be more reliable?

thanks

Err:6 http://apt.armbian.com trixie/main arm64 armbian-plymouth-theme all 25.8.2
  Hash Sum mismatch
  Hashes of expected file:
   - SHA512:718d46957b9e9940ba7569761069864c46b07bd5570db462894b81d2730803dc9f9b0618ed45104c6357b92ddf00600a9664b93bd3eaca8c453b4724ba495688
   - SHA256:3ee8733f28c38f66f3a1328c93bf75d00416f8e2d1e7a5c91f4727489d7c1b00
   - SHA1:2ad501942596de1a53e9339284635a712346a245 [weak]
   - MD5Sum:a7dc1e7a3ff05af314e49c0b841ce240 [weak]
   - Filesize:112140 [weak]
  Hashes of received file:
   - SHA512:f37ac430cdadcacde0d016447ff82f58ee81f9142523a39252096fc09cdb90542346bfb496be7993502ac309cfae68d22a740b4d5aadb66b687b89ad88ed4d80
   - SHA256:b9a7ed2ceebe4cce4aab2f4366c8a1bd3479dec7923294b231cf529bfff137eb
   - SHA1:76b110fec39b59188a68e1c7e67aeb18de411bc3 [weak]
   - MD5Sum:3bc7dc9b0ba091d9227cc3693847ed97 [weak]
   - Filesize:112140 [weak]

I'm trying to connect a MIPI DSI display.

Currently, backlight is working, but not the display in Armbian (Armbian 25.5.1 Noble Gnome).

DTS is loaded and corresponding kernel module panel-simple-dsi is loaded as well.

Same DTS works on the official Radxa 5c image (rock-5c_bookworm_kde_b2) (kernel 6.1.43-15)

Has anyone faced a similar issue?

armbianmonitor -u : https://paste.armbian.com/ocoperohak.yaml

Thanks!

You can see that I tested on both kernel 6.1.43 (stable) and latest edge and it's not working.

But this daily release work like charm.

I'm using

4GB Radxa Rock 5C Lite

Armbian_25.5.1_Rock-5c_bookworm_vendor_6.1.115_minimal

Some guides mention that one should enable an overlay. I didn't find any relevant overlays in armbian-config. In the Radxa repo I found rock-5a-radxa-25w-poe.dts which specifies that it's also compatible with Rock 5C. I've compiled it and enabled it, but by default the fan is not spinning (on high temps) and I'm not sure how to investigate that. 

Also, does it matter that I have 5C Lite? As it has another chip: RK3582

Here is what I have tested:

LAN             yes
WiFi             yes
BT                yes
USB3          *partly, some devices are not detected at all, some will take a few minutes before detected*
GPU            Mali-G610 (Panfrost)
HDMI audio        *no*
Fan control        yes
temp. sensor htop    *no*
Temp. sensor Gnome    *no*
Other: some cursor graphic glitches

Armbian-unofficial_25.05.0-trunk_Rock-5c_noble_current_6.12.28_gnome_desktop.img

Any ideas on how to get more features supported?

I installed  https://dl.armbian.com/rock-5c/Bookworm_current_minimal-homeassistant, configured it to my liking (OS on a mirrored ZFS pool) to discover there is no WiFi, no Bluetooth.

It's now kernel 6.12.17-current-rockchip64.

Anybody managed to get WiFi and BT working with this kernel?

Thanks,

Chris

the wlan0 does not appear on iwctl neither ip address commands, but the device (AIC Wlan) still appears on lsusb command:

$ lsusb
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 004: ID a69c:8d80 aicsemi AIC Wlan
Bus 005 Device 002: ID 1a40:0101 Terminus Technology Inc. Hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

armbianmonitor output:
https://paste.armbian.com/oqewipobin

I don't know if there is an issue with the newest kernel update, or if there is some overlay or kernel module for the AIC Wlan chip that is being erased/disabled during the kernel update process.

Is there something I can try to reenable the wlan0 interface? or is it just a bronken update?

Judging by the entries of journalctl, suspend is triggered in the kernel, not in systemd

$ journalctl -b | grep -i suspend
Feb 26 11:00:29 rock-5c kernel: rk806 spi2.0: dvs-suspend-control-by missing!
Feb 26 11:00:29 rock-5c kernel: rockchip-dmc dmc: suspend_rate = 528000000
Feb 26 11:00:29 rock-5c kernel: rockchip-dmc dmc: deep_suspend_rate = 2112000000
Feb 26 11:00:29 rock-5c kernel: rockchip-pm rockchip-suspend: not set pwm-regulator-config
Feb 26 11:00:29 rock-5c kernel: rockchip-suspend not set sleep-mode-config for mem-lite
Feb 26 11:00:29 rock-5c kernel: rockchip-suspend not set wakeup-config for mem-lite
Feb 26 11:00:29 rock-5c kernel: rockchip-suspend not set sleep-mode-config for mem-ultra
Feb 26 11:00:29 rock-5c kernel: rockchip-suspend not set wakeup-config for mem-ultra

Can anyone tell me what the cause is and how I can fix it?

armbian-hardware-monitor.log rock5c-debug.log

https://radxa.com/products/accessories/heatsink-6540b/

After installing the Armbian server image, I ran these two commands:

```bash

ls /sys/class/thermal/cooling_device*/type

cat /sys/class/thermal/cooling_device*/type

```

and found that there is no `pwm-fan`.

Then I installed the official Radxa Debian image and ran these two commands again. `pwm-fan` exists and I can make it starts spinning by running:

```bash

echo 255 | sudo tee /sys/devices/platform/pwm-fan/hwmon/hwmon*/pwm1

```

Is the fan module supported in Armbian? If yes, how do I activate it?

When launching `armbian-install`, there's only one option:

(5) - Install to SD card

I would like to install the bootloader to the SPI flash module but the option is not present.

Furthermore it seems that my SPI module isn't detected either when running ls /dev/mtd* -> no mtdblock

I decided to move on and I flashed https://dl.radxa.com/rock5/5c/images/loader/spi/rock-5c-spi-image-20240528.img to my 5C lite SPI flash module.

However, there's no display and both LEDs are lighted up (green and blue) without blinking. I suggest it didn't work well.

Can someone confirm?

BR

Here is what I've done initially: I bought a rock 5c and a penta sata hat.
-I installed Armbian_24.5.1_Rock-5c_bookworm_edge_6.8.10_minimal.
-I installed OMV (configure some samba shared folder)
-I installed ZFS (for that I needed linux headers that I found online because there were not included)
-I create a ZFS pull with two SSD.

-I installed immich and setup a cloudflare tunel to use it.
-I installed plex media server.

That's pretty much all I have setup on my SBC.
I've done apt upgrade multiple time & update some immich / Plex.
Every time I did update I rebooted the SBC.
And then yesterday I did an immich & plex update, apt upgrade and lastly rebooted.
And my SBC never did come back online.

I try to install a fresh armbian install to see if it still boot and it did boot.

I'm not sure where to start to get it boot again with keeping has much stuff has I can.
I wanted to try this:
https://docs.armbian.com/User-Guide_Recovery/#replacing-boot

But I'm not sure what Root file system, Kernel, Firmware & Device Tree Binary (DTB) version I should take.

Or maybe someone could point me to an other path to fix my install?

I am running the latest Armbian image with Noble + GNOME for the Rock 5C.

I have build it using the `compile.sh` script without altering the kernel, desktop enabled, based on Noble, with GNOME, no applications, no extensions.

Added the kisak PPA repo afterwards and enabled the panthor overlay for hardware acceleration.

Should be close to the `Armbian_24.11.1_Rock-5c_noble_vendor_6.1.75_gnome-kisak_desktop.img` image, I think.

With Chromium (few tabs), VSCodium (working on some code) and a couple of terminals open, things were crashing all the time.

Here is a reproducable example with Chromium, when navigating to the URL:

https://www.geeksforgeeks.org/ulimit-soft-limits-and-hard-limits-in-linux/

sander@rock-5c:~$ chromium 
[3743:3743:1213/231308.263364:ERROR:object_proxy.cc(576)] Failed to call method: org.freedesktop.ScreenSaver.GetActive: object_path= /org/freedesktop/ScreenSaver: org.freedesktop.DBus.Error.NotSupported: This method is not part of the idle inhibition specification: https://specifications.freedesktop.org/idle-inhibit-spec/latest/
[3743:3795:1213/231308.438912:ERROR:backend_impl.cc(989)] Critical error found -8
[3743:3795:1213/231308.439341:ERROR:entry_impl.cc(955)] Failed to save user data
[3743:3795:1213/231308.821432:ERROR:backend_impl.cc(989)] Critical error found -8
[3743:3795:1213/231308.821616:ERROR:entry_impl.cc(955)] Failed to save user data
[3743:3743:1213/231308.821621:ERROR:gpu_disk_cache.cc(233)] Failed retry to open blob cache entry: -2
[3845:3861:1213/231317.658891:ERROR:ffmpeg_common.cc(970)] Unsupported pixel format: -1
[4052:4052:1213/231324.240574:ERROR:platform_thread_posix.cc(155)] pthread_create: Resource temporarily unavailable (11)
[4057:4057:1213/231324.266795:ERROR:platform_thread_posix.cc(155)] pthread_create: Resource temporarily unavailable (11)
[3743:3793:1213/231324.269115:ERROR:zygote_communication_linux.cc(164)] Did not receive ping from zygote child
[3743:3793:1213/231324.269180:FATAL:check.cc(361)] Check failed: false. NOTREACHED log messages are omitted in official builds. Sorry!
[3764:3764:1213/231324.269109:ERROR:zygote_linux.cc(639)] Zygote could not fork: process_type renderer numfds 5 child_pid -1
[1213/231324.290657:ERROR:elf_dynamic_array_reader.h(64)] tag not found
Trace/breakpoint trap

I was also not able to use Firefox, at all. Every new tab ended up in a "Snap. Your page crashed" view.

The root cause seems to be this:
 

ERROR:platform_thread_posix.cc(155)] pthread_create: Resource temporarily unavailable (11)

After some web searching, I found that the thread limits are set to a very low value.

(note "max user processes")

sander@rock-5c:~$ cat /proc/sys/kernel/threads-max
1685

sander@rock-5c:~$ ulimit -a
real-time non-blocking time  (microseconds, -R) unlimited
core file size              (blocks, -c) 0
data seg size               (kbytes, -d) unlimited
scheduling priority                 (-e) 0
file size                   (blocks, -f) unlimited
pending signals                     (-i) 842
max locked memory           (kbytes, -l) 1015884
max memory size             (kbytes, -m) unlimited
open files                          (-n) 1024
pipe size                (512 bytes, -p) 8
POSIX message queues         (bytes, -q) 819200
real-time priority                  (-r) 0
stack size                  (kbytes, -s) 8192
cpu time                   (seconds, -t) unlimited
max user processes                  (-u) 842
virtual memory              (kbytes, -v) unlimited
file locks                          (-x) unlimited

I searched through the Armbian build repository for code that sets these limits, but I didn't find any.

Seems that these limits are set or calculated by rockchip linux kernel.

After applying a few configuration changes, the system becomes much more stable and I have not had any crashes so far.

# /etc/rc.local  (updated)
echo 16384 > /proc/sys/kernel/threads-max

# /etc/security/limits.d/99-nproc.conf   (created)
* soft nproc 4096
* hard nproc 4096

# /etc/systemd/system.conf  (updated)
#DefaultTasksMax=15%
DefaultTasksMax=infinity

After a reboot, the changes are now applied. And no more crashes! And Firefox now works as well.

sander@rock-5c:~$ cat /proc/sys/kernel/threads-max
16384

sander@rock-5c:~$ ulimit -u
4096

Hope this is useful to someone else.

I followed instructions by amazingfate in this forum to create a small SD card with a u-boot image, ie

1. I created a complete Armbian image (vendor kernel) on an SD card too boot up the Rock 5c Lite
2. A second, small capacity SD card was inserted into the USB port using a USB adapter
3. U-boot was transferred from /usr/lib/linux-u-boot-*/ to the small SD card:
   • dd if=./idbloader.img of=/dev/sda seek=64 conv=notrunc status=progress
   • dd if=./u-boot.itb of=/dev/sda seek=16384 conv=notrunc status=progress
4. My chosen Armbian image was transferred to the NVME drive using Balena Etcher

 Finally I use the small SD card with u-boot in the SD card slot on the 5C Lite and the NVME drive goes in the NVME hat.

I tried two different images from here on the NVME drive

1. Debian 12 (Bookworm) with XFCE and bleeding edge kernel v6.11
2. Debain 12 (Bookworm) with XFCE and  vendor kernel v6.1

The board boots fine from the NVME using the  v6.11 kernel, but the implementation seems to be nowhere near complete. The HDMI port doesn't work, the fan is spinning at full speed but is difficult to control because CPU temp is not reported properly, etc. The bord performs well though, and reports eight functioning CPU's.

The board does not boot from the NVME using the v6.1 vendor kernel. It tries to start up the kernel but gets stuck. Please see the attachment below for a copy of my complete console output at high verbosity.

Would someone be able to help to get the vendor kernel to work?

UART-Log_Vendor-Kernel.txt

/usr/bin/armbianmonitor: ligne 976: iostat : commande introuvable

img used : Armbian_24.8.4_Rock-5c_bookworm_vendor_6.1.75-omv_minimal.img.xz

hardware :
https://docs.radxa.com/en/accessories/penta-sata-hat
https://docs.radxa.com/en/rock5/rock5c
4 ssd samasung evo 870

The image works perfectly when flashed on a SD card and booting from the SD card, the Radxa pentaHat works, the disk are powered (green led for the hat, blue led per each disk).

However, when the image is flashed on emmc, the OS boot normaly but the pentaHat does not work, the disk are not powered and not detected by the os (green led Ok, no blue led for the disk)

Does any of you have an idea why it works using the SD card and not with the emmc ? is their some settings or overlay that could help fix this issue.

I tried the radxa img for the rock5c and it works with either emmc or sd card (https://github.com/radxa-build/rock-5c/releases)

Thank you for your answers and help!

Thru desperation I found an Android image that booted and had screen output, so the HDMI works atleast.

After stuffing around I found that the u-boot image extracted from the Rock-5D t2(rsdk) and injected into Rock-5C b1(rsdk) Bookworm_kde image boots and has working screen.

Longer story short, getting Armbian 24.11 to work... Narrowed it down from replacing the entire u-boot.itb, I can get a working desktop with kernel version 5.10 Bookworm by removing the rng@fe378000 trngvl section (enabled mali400/bifrost driver in kernel) from u-boot, this atleast has a working system, problem is that there is no fan control with any of the 5.10 builds I've tried.

Kernel 6.1 and 6.11 these atleast have fan control but back to no HDMI output, tried the same method of removing rng from u-boot but system fails to boot.

At a loss to get HDMI working on newer builds, has anyone had any success or ideas

Running the check rk3582 script shows there is a GPU:

Rock 5C 4Gb
CPU:    7
GPU:    Yes
Enc0:    Yes
Enc1:    Yes
Dec0:    Yes
Dec1:    Yes

removed.bin

Thanks

First I flashed `Armbian_24.5.1_Rock-5c_noble_vendor_6.1.43.img.xz` wich doesn't work. Log from first boot is attached at the bottom.

Second I flashed `Armbian_24.5.1_Rock-5c_noble_edge_6.8.10.img.xz` wich is working well. SSH comes up as usual.

Would be nice to use the vendor kernel (6.1.43) instead of the bleeding edge (6.8.10) one, because it is not reccommend and not all features are working.

I OCR a screenshot from first boot with `Armbian_24.5.1_Rock-5c_noble_vendor_6.1.43.img.xz`

Welcome to Armbian 24.5.1 noble!

[ OK ] Created slice system-modprobe.slice Slice/system/modprobe.
[ OK ] Created slice system-serial\x2dgetty.slice Slice /system/serial-getty.
[ OK ] Created slice user.slice User and Session Slice.
[ OK ] Started systemd-ask-password-wall.path Forward Password Requests to Wall Directory Watch.
[ OK ] Set up automount proc-sys-fs-binfmt_misc.automount Arbitrary Executable File Formats File Se
Expecting device dev-ttyFIQ0.device /dev/ttyFIQ0.
[ OK ] Reached target integritysetup.target Local Integrity Protected Volumes.
[ OK ] Reached target slices.target Slice Units.
[ OK ] Reached target swap.target - Swaps.
[ OK ] Reached target time-set.target System Time Set.
[ OK ] Reached target veritysetup.target Local Verity Protected Volumes.
[ OK ] Listening on rpcbind.socket RPCbind Server Activation Socket.
[ OK ] Listening on syslog.socket Syslog Socket.
[ OK ] Listening on systemd-fsckd.socket fsck to fsckd communication Socket.
[ OK ] Listening on systemd-initctl.socket initctl Compatibility Named Pipe.
[ OK ] Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[ OK ] Listening on systemd-journald.socket Journal Socket.
[ OK ] Listening on systemd-udevd-control.socket udev Control Socket.
[ OK ] Listening on systemd-udevd-kernel.socket udev Kernel Socket.
Mounting dey-hugepages.mount Huge Pages File System...
Mounting dey-mqueue.mount POSIX Message Queue File System...
Mounting sys-kernel-debug.mount Kernel Debug File System...
Mounting sys-kernel-tracing.mount Kernel Trace File System...
Starting fake-hwclock-load.service Restore the current clock...
Starting keyboard-setup, service Set the console keyboard layout...
Starting kmod-static-nodes, service Create List of Static Device Nodes...
Starting modprobe@configfs, service Load Kernel Module configfs...
Starting modprobe@dm_mod, service Load Kernel Module dm_mod... [43.282597] systemd[1]: Caught <SEGV> from PID -1444467920.
[ 43.286703] systemd[1]: Caught <SEGV>, core dump failed (child 393, code killed, status=11/SEGV).
[ 43.290634] systemd[1]: Freezing execution.