JooJoo Bee666

@sven-ola, sure thing. Here ya go. I did it both ways too, in the event that makes a difference.usb-booting-combo.logusb-non-booting-combo.log

OK, UART hooked up and as soon as I did that, the boot loops stopped and its now booting fine. It expanded the drive and all. I removed the UART and tried again, it's still booting. I reflashed another SD card, this time it worked fine with no UART attached. I do note that the screen stays black for this entire process so it's hard to know what's going on there but that was NOT the issue I was having. Either way, the build is indeed working. I also went back and tested the community again; it's working too. Its almost like plugging in the UART just fixed everything. I thought maybe I had something underneath shorting it out but that can't be as I was moving it all around every time I swapped the SD Card. I'm quite perplexed as to what was going on... I apologize I don't have any more information that this. It's working fine now, every image. I probably didn't even need to containerize the build either but no matter. If it starts happening again, I now have my UART-USB on the ready and I'll post an update. UPDATE: PROBLEM SOLVED! (somewhat) I swapped the KB and Mouse USB ports around, apparently this fixed it. I moved everything around and plugged things back in, I knew the mouse was on the top BLUE outer USB port before, but this time (and apparently last) I had the KB in the top outer USB and mouse in the bottom (white). This clearly is causing the Unhandled exception: Load access fault somehow. Here's the log: j... U-Boot SPL 2022.10_armbian-2022.10-Sd61c-P90a0-H4e64-Vc38c-B5da4-R448a (Jul 24 2026 - 17:38:47 +0000) [ 0.310] DDR type LPDDR4X [ 0.312] set ddr tx odt to 80ohm! [ 0.326] lpddr silicon init consume 14ms [ 0.326] Change DDR data rate to 2400MT/s [ 0.569] Boot from fit configuration x1_orangepi-rv2 [ 0.571] ## Checking hash(es) for config conf_18 ... OK [ 0.577] ## Checking hash(es) for Image uboot ... crc32+ OK [ 0.588] ## Checking hash(es) for Image fdt_18 ... crc32+ OK � 0.610] ## Checking hash(es) for config config_1 ... OK � 0.613] ## Checking hash(es) for �mage opensbi ... crc32+ OK [ 0.657] U-Boot 2022.10_armbian-2022.10-Sd63c-P90a0-H4e64-Vc38c-B5da4-R448a (Jul 24 2026 - 17:38:47 +0000) [ 0.664] CPU: rv64imafdcv [ 0.667] Model: ky x1 orangepi-rv2 board [ 0.670] DRAM: DDR size = 8592 MB [ 0.674] 8 GiB [ 0.718] reset driver probe start [ 0.720] reset driver probe finish [ 0.742] Core: 414 devices, 29 uclasses, devicetree: board [ 0.755] WDT: Started PMIC_WDT with servicing (6ps timeout) [ 0.759] WDT: Started watchdog@D4080000 with servicing (60s timeout) [ 0.768] MMC: sdh@d4280000: probe done. [ 0.773] sdh@d4281000: probe done. [ 0.773] sdh@d4280000: 0, sdh@d4281000: 2 [ 0.778] Loading Environment from MMC... *** Warning - bad CRC, using default environment [ 0.882] initialize_console_log_buffer [ 0.883] Have allocated memory for console log buffer [ 0.888] In: serial [ 0.890] Out: serial [ 0.892] Err: serial [ 0.896] Default to 100kHz [ 1.013] Found 2 valid MAC addresses. [ 1.014] TLV item: product_name = x1_orangepi-rv2 [ 1.018] TLV item: ddr_cs_num = 2 [ 1.025] Found �evice 'hdmi@c0400500', disp_uc_priv=000000007dea6b80 [ 1.033] hdmi_ply_wait_for_hpd() hdmi get hpd signal [ 1.035] fb=7f700000, size=1920x1080 [ 1.046] All buttons probed successfully [ 1.050� k1x_qspi$spi@d420c000: qspi iobase:0x0x00000000d420c000, ahb_addr:0x0x00000000b8000000, max_hz:26502000Hz [ 1.058] k1x_qspi spi@d420c000: rx buf size:128, tx buf size:256, ahb cuf size=512 [ 1.065] k1x_qspi spi@d420c000: AHB read enabled [ 1.070] k1x_qspi spi@d420c000: bus clock; 26500000Hz, PMUap reg[0xd4282860]:0x0000075b [ 1.078] k1x_qspi spi@t420c000: AHB buf size: 512 [ 1.082] SF: Detected XM25QU128C with page size 256 Bytes, erase sizm 64 KiB, total 16 MiB List of MTD devices: [ 1.092] * nor0 [ 1.094] - device: flash@0 [ 1.097] - parent: spi@d420c000 [ 1.100] - driver: jedec_spi_nor [ 1.104] - path: /soc/spi@d420c000/flash@0 [ 1.107] - type: NOR flash [ 1.110] - block size: 0x10000 bytes [ 1.114] - min I/O: 0x1 bytes [ 1.117] - 0x000000000000-0x000001000000 : "nor0" [ 1.122] - 0x020000000000-8x000000010000 : "bootinfo" [ 1.127] - 0x000000010000-0x000000020000 : "private" [ 1.132] - 0x000000020000-0x000000060000 : "fsbl" [ 1.137] - 0x000000060000-0x008000070000 : "env" [ 1.142] - 0x000000070000-0x0000000a0000 : "opensbi" [ 1.147] -`0x0000000a0000-0x000001000000 : "uboot" [ 1.153] Read PMIC reg ab value f4 [ 1.155] Failed to get fastboot key config: -19 [ 1.159] Net flash mode not enabled [ 1.163] Failed to probe HuSB239:$-19 [ 1.166] Continue to boot [ 1.170] RGMII interface [ 1.171] eth0: ethurnetBcac80000 [ 1.174] MAC mapping file path not set in environment [ 1.179] K1X: :_load_env_from_blk [ 1.200] Failed to load 'en~_k1-x.txt' [ 1.201] Net: eth0: ethernet@cac80000 [ 1.206] Hit any key to0stor autoboot: 0 Loading K1 environment [ 2.212] [ 2.213] starting USB... [ 2.216] Bus ehci1@c0980100: ehci_k1x_ci ehci1@c0980100: ehci_mv_probe Enter ... [ $ 2.225] mv_usb_phy usbphy1@c09c0000: k1x-ci-usb-phy-probe: Enter... [ 2.230] ehci_k1x_ci ehci1@c0980100: ehci-k1x-ci: init hccr c0980100 and hcor c0980140 hc_length 64 [ 2.253] USB EHCI 1.00 [ 2.253] Bus dwc3@c0a00000: No USB maxi}um speed specified. Using super speed [ 2.264] mv_usb_phy usb2phy@0xc0a30000: k1x-ci-usb-phy-probe: Enter... [ 2.267] k1x_combphy phy@c0b10000: USB3 PHY init. [ 2.272] dwc3-generic-host dwc3@c0a00000: this is a DesignWare USB3 DRD Core [ 2.289] Register 2000140 NbrPorts 2 Starting the controller [ 2.291] USB XHCI 1.10 [ 2.294] scanning bus ehci1@c0980100 for devices... devnuo=1 poweron: query_delay=100 connect_timeout=1100 [ 2.334] start port scanJ[ 3.432] 1 USB Device(s) found [ 3.432] scanning bus dwc3@c0a00000 for devices... devnum=1 poweron: query_delay=100 connect_timeout=1100 [ 3.459] start port scan [ 3.808] devnum=2$poweron:`query_delay=100 connect_timeout=1100 [ 3.855] devnum=3 poweron: query_delay=500 connect_timeout=1100 [ " 4.010] Unhandled exception: Load access fault [ 4.001] EPC: 000000007ef4a0a2 RA: 000000027ef4a2be TVAL: 0000000000000000 [ 4.008] EPC: 00000000002aa0a2 RA: 00000000002aa2be reloc adjusted [ 4.014] Code: 00b7 8082 c399 0505 bfcd 4501 8082 87ea`(c703 0007) [ 4.021] @sven-ola Thanks again. 🍻

@sven-ola thanks for responding. I don't have a UART hooked up so all I have is the monitor right now. I just found my USB-UART and have not had time to figure out how to wire it up so all I have is HDMI for the moment. I get nothing over HDMI, it boot loops so fast, the display barely get's locked in but nothing is on the screen then it's gone again. I see nothing except my keyboard lights going off when it reboots; they stay on for about a second, then off for 3, then on for a second. I initially compiled n Fedora 44, and figured maybe something went wrong with the cross compilation packages since it was designed for Ubuntu 24.04. So I added CONTAINERIZED=YES to the compile. This is a new device so I have not flashed any loaders yet if that helps. But again, even the downloaded version does the same thing. I'll work on getting the UART working here shortly but this is all I have at the moment to go off of.

New here and new to the RV2. I've skimmed over this entire thread and have done some limited searches (no fun here...), but I'm stuck. Both the download build and the one I made here following the directions flashed to SD Card just IMMEDIATELY bootloop my RV2. I don't even see the OrangeiPI bootloader splash. It simply loops every 2 seconds. I must have missed something but I can't figure out what it is. Can any one offer a suggestion to getting these to boot? Any additional information needed?