Marvell>> bubt flash-image-DDR3-2g_2cs_7-600_600.bin
Burning U-BOOT image "flash-image-DDR3-2g_2cs_7-600_600.bin" from "tftp" to "spi"
Using neta@30000 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.253
Filename 'flash-image-DDR3-2g_2cs_7-600_600.bin'.
Load address: 0x8000000
Loading: #############################################################
         4.8 MiB/s
done
Bytes transferred = 895012 (da824 hex)
Image checksum...OK!
722980 bytes written, 172032 bytes skipped in 8.713s, speed 105174 B/s
Done!
Marvell>> reset
resetting ...
TIM-1.0
WTMI-devel-18.12.1-e6bb176
WTMI: system early-init

DDR topology parameters:
========================
ddr type               DDR3
ddr speedbin           12
bus width              16-bits
cs num                 2
  cs[0] - group num    0
  cs[0] - bank num     8
  cs[0] - capacity     1024MiB
  cs[1] - group num    0
  cs[1] - bank num     8
  cs[1] - capacity     1024MiB
CPU VDD voltage default value: 1.108V

DRAM windows:
=============
WIN[0] - base addr     0x60000000
WIN[0] - size          0x40000000
WIN[1] - base addr     0xa0000000
WIN[1] - size          0x20000000

memory test region:
===================
CS[0]                  0x60000000 - 0x9fffffff
CS[1]                  0xa0000000 - 0xbfffffff

SELF-REFRESH TEST PASS
SELF-REFRESH TEST PASS
CS0: QS GATE TRAINING PASSED
CS1: QS GATE TRAINING PASSED
DLL TUNING PASSED
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.5(debug):1f8ca7e (Marvell-devel-18.12.2)
NOTICE:  BL1: Built : 09:15:30, Oct 20 2020
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.5(debug):1f8ca7e (Marvell-devel-18.12.2)
NOTICE:  BL2: Built : 09:15:30, Oct 20 2020
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: v1.5(debug):1f8ca7e (Marvell-devel-18.12.2)
NOTICE:  BL31: Built : 09:15:30, Oct

U-Boot 2018.03-devel-18.12.3-armbian (Oct 20 2020 - 09:15:15 +0000)

Model: Marvell Armada 3720 Community Board ESPRESSOBin
       CPU     600 [MHz]
       L2      800 [MHz]
       TClock  200 [MHz]
       DDR     600 [MHz]
DRAM:  2 GiB
Comphy chip #0:
Comphy-0: USB3          5 Gbps
Comphy-1: PEX0          2.5 Gbps
Comphy-2: SATA0         6 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link down
MMC:   sdhci@d0000: 0, sdhci@d8000: 1
Loading Environment from SPI Flash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Model: Marvell Armada 3720 Community Board ESPRESSOBin
Net:   eth0: neta@30000 [PRIME]
Hit any key to stop autoboot:  0
starting USB...
USB0:   Register 2000104 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
/
** Bad device usb 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
** Bad device usb 0 **
## Executing script at 06d00000
Wrong image format for "source" command
scanning bus for devices...

Device 0: unknown device
/
** Bad device scsi 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
** Bad device scsi 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/
Card did not respond to voltage select!
** Bad device mmc 1 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
Card did not respond to voltage select!
** Bad device mmc 1 **
## Executing script at 06d00000
Wrong image format for "source" command
/
** File not found /boot.scr **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
3185 bytes read in 13 ms (239.3 KiB/s)
## Executing script at 06d00000
Boot script loaded from  0
** Bad device 0 0x9000000 **
** Bad device specification 0 /boot/uInitrd **
** Bad device specification 0 /boot/Image **
** Bad device specification 0 /boot/dtb/ **
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
** Bad device 0 0x9000000 **
** Bad device 0 0x9000000 **
Applying user provided fixup script (fixup.scr)
## Executing script at 09000000
Wrong image format for "source" command
Bad Linux ARM64 Image magic!
Marvell>> printenv
baudrate=115200
boot_a_script=ext4load ${boot_interface} ${devnum}:1 ${scriptaddr} ${prefix}boot.scr;source ${scriptaddr};
boot_interface=mmc
boot_prefixes=/ /boot/
boot_targets=usb sata mmc1 mmc0
bootargs=root=/dev/mmcblk0p1 rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 consoleblank=0 loglevel=1 ubootpart= usb-storage.quirks=   cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
bootcmd_mmc0=setenv devnum 0; setenv boot_interface mmc; run scan_dev_for_boot;
bootcmd_mmc1=setenv devnum 1; setenv boot_interface mmc; run scan_dev_for_boot;
bootcmd_sata=setenv devnum 0; scsi scan; scsi dev 0; setenv boot_interface scsi; run scan_dev_for_boot;
bootcmd_usb=setenv devnum 0; usb start;setenv boot_interface usb; run scan_dev_for_boot;
bootdelay=2
bootlogo=false
console=both
consoleargs=console=ttyS2,1500000 console=tty1
devnum=0
docker_optimizations=on
earlycon=off
eth1addr=00:51:82:11:22:01
eth2addr=00:51:82:11:22:02
eth3addr=00:51:82:11:22:03
ethact=neta@30000
ethaddr=00:51:82:11:22:00
ethprime=eth0
fdt_addr=0x6000000
fdt_high=0xffffffffffffffff
fdt_name=fdt.dtb
fdtcontroladdr=7f62d490
fileaddr=6d00000
filesize=c71
gatewayip=10.4.50.254
get_images=tftpboot $kernel_addr $image_name; tftpboot $fdt_addr $fdt_name; run get_ramfs
get_ramfs=if test "${ramfs_name}" != "-"; then setenv ramfs_addr 0x8000000; tftpboot $ramfs_addr $ramfs_name; else setenv ramfs_addr -;fi
hostname=marvell
image_name=Image
initrd_addr=0x1100000
initrd_image=uInitrd
initrd_size=0x2000000
ipaddr=0.0.0.0
kernel_addr=0x7000000
load_addr=0x9000000
loadaddr=0x8000000
netdev=eth0
netmask=255.255.255.0
overlay_error=false
ramfs_addr=0x8000000
ramfs_name=-
root=root=/dev/nfs rw
rootdev=/dev/mmcblk0p1
rootfstype=ext4
rootpath=/srv/nfs/
scan_dev_for_boot=for prefix in ${boot_prefixes}; do echo ${prefix};run boot_a_script; done
scriptaddr=0x6d00000
serverip=192.168.10.1
set_bootargs=setenv bootargs $console $root ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:none nfsroot=$serverip:$rootpath $extra_params
stderr=serial@12000
stdin=serial@12000
stdout=serial@12000
verbosity=1

Environment size: 2298/65532 bytes
Marvell>>

 

Apologies, I couldn't move the code block once I'd put it in here.

 

I'm trying to boot Armbian_20.08.2_Espressobin_buster_current_5.8.6.img written onto a known-good SD card. I've tried both on an older bootloader and the 2018 one suggested by Armbian.

 

On 10/20/2020 at 11:55 AM, voltagex said:

I've tried both on an older bootloader and the 2018 one suggested by Armbian.

 

The image "flash-image-DDR3-2g_2cs_7-600_600.bin" is not from the EspressoBin download page. Please try the current ones - they are from Sept. 2020 - branch 18.12-fixed.

The ones you have tied were probably produced by the Armbian build system on the fly and are not tested.

Weird, flashed back to the one you suggested now that the download page is back up, had the same issue - must have been the SD card after all.

 

It's also now working with my 2020.10 bootloader!