November 13, 20241 yr I builded u-boot for orangepi3B from https://github.com/orangepi-xunlong/orangepi-build repo and I compiled armbian with officiall repo wit this config:https://github.com/armbian/build/blob/main/config/boards/orangepi3b.csc GitHub (https://github.com/orangepi-xunlong/orangepi-build). Problem: Data: - Version (branch) u-boot cloned form orangepi-build official repo: - Debug via UART from OPI3B: CONQ., [13.11.2024 10:14] DDR Version V1.10 20210810 ln ddrconfig:7 LPDDR4X, 324MHz BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB tdqss: cs0 dqs0: -72ps, dqs1: -168ps, dqs2: -96ps, dqs3: -168ps, tdqss: cs1 dqs0: -72ps, dqs1: -144ps, dqs2: -96ps, dqs3: -168ps, change to: 324MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x64 change to: 528MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x58 change to: 780MHz PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:41% dram drv:40,odt:0 clk skew:0x58 change to: 1056MHz(final freq) PHY drv:clk:36,ca:36,DQ:29,odt:60 vrefinner:16%, vrefout:22% dram drv:40,odt:80 vref_ca:00000071 clk skew:0x46 cs 0: the read training result: DQS0:0x40, DQS1:0x3d, DQS2:0x44, DQS3:0x3b, min : 0xf 0x10 0x10 0x10 0x2 0x3 0x6 0x6 , 0x5 0x6 0x4 0x2 0xa 0xd 0xe 0xf , 0x2 0x1 0xf 0x11 0xe 0xc 0xe 0xd , 0x6 0x5 0x9 0x1 0xb 0xd 0xc 0xd , mid :0x2a 0x2a 0x2c 0x2b 0x20 0x21 0x24 0x24 ,0x23 0x25 0x22 0x20 0x27 0x2c 0x2e 0x2d , 0x22 0x22 0x2f 0x2e 0x2b 0x2b 0x2c 0x2a ,0x22 0x22 0x27 0x1e 0x2a 0x2a 0x2a 0x2a , max :0x46 0x44 0x49 0x46 0x3e 0x40 0x42 0x43 ,0x42 0x45 0x41 0x3f 0x44 0x4c 0x4e 0x4b , 0x43 0x43 0x4f 0x4c 0x49 0x4b 0x4a 0x48 ,0x3f 0x3f 0x46 0x3c 0x4a 0x47 0x48 0x47 , range:0x37 0x34 0x39 0x36 0x3c 0x3d 0x3c 0x3d ,0x3d 0x3f 0x3d 0x3d 0x3a 0x3f 0x40 0x3c , 0x41 0x42 0x40 0x3b 0x3b 0x3f 0x3c 0x3b ,0x39 0x3a 0x3d 0x3b 0x3f 0x3a 0x3c 0x3a , the write training result: DQS0:0x3d, DQS1:0x30, DQS2:0x3a, DQS3:0x30, min :0x59 0x5b 0x5c 0x5c 0x51 0x52 0x54 0x5a 0x58 ,0x4a 0x4d 0x49 0x47 0x4f 0x53 0x55 0x55 0x51 , 0x4a 0x4b 0x54 0x55 0x53 0x53 0x56 0x57 0x56 ,0x4b 0x4c 0x4e 0x49 0x53 0x53 0x53 0x53 0x4d , mid :0x75 0x76 0x76 0x77 0x69 0x6a 0x6d 0x72 0x70 ,0x66 0x64 0x62 0x61 0x68 0x6d 0x6d 0x70 0x6b , 0x65 0x62 0x6f 0x71 0x6c 0x6b 0x6e 0x6e 0x6e ,0x65 0x63 0x67 0x60 0x6c 0x6c 0x6d 0x6c 0x64 , max :0x92 0x91 0x91 0x92 0x82 0x83 0x87 0x8b 0x89 ,0x83 0x7c 0x7c 0x7c 0x81 0x87 0x86 0x8b 0x85 , 0x80 0x7a 0x8b 0x8d 0x86 0x84 0x86 0x86 0x87 ,0x80 0x7b 0x80 0x78 0x86 0x86 0x87 0x85 0x7c , range:0x39 0x36 0x35 0x36 0x31 0x31 0x33 0x31 0x31 ,0x39 0x2f 0x33 0x35 0x32 0x34 0x31 0x36 0x34 , 0x36 0x2f 0x37 0x38 0x33 0x31 0x30 0x2f 0x31 ,0x35 0x2f 0x32 0x2f 0x33 0x33 0x34 0x32 0x2f , cs 1: the read training result: DQS0:0x42, DQS1:0x3c, DQS2:0x44, DQS3:0x3c, min : 0xf 0xf 0xf 0x10 0x1 0x2 0x5 0x7 , 0x5 0x6 0x3 0x1 0x9 0xd 0xe 0xf , 0x3 0x1 0xf 0xf 0xd 0xb 0xe 0xc , 0x6 0x6 0x9 0x1 0xa 0xd 0xd 0xb , mid :0x2c 0x2c 0x2e 0x2d 0x21 0x23 0x24 0x27 ,0x22 0x26 0x21 0x1f 0x26 0x2c 0x2d 0x2f , 0x22 0x22 0x2f 0x2e 0x2b 0x2b 0x2c 0x2a ,0x23 0x23 0x28 0x1f 0x2a 0x2b 0x2b 0x29 , max :0x4a 0x49 0x4e 0x4a 0x41 0x44 0x44 0x48 ,0x40 0x46 0x40 0x3d 0x44 0x4c 0x4c 0x4f , 0x42 0x44 0x4f 0x4d 0x49 0x4b 0x4b 0x49 ,0x41 0x41 0x47 0x3e 0x4a 0x4a 0x4a 0x47 , range:0x3b 0x3a 0x3f 0x3a 0x40 0x42 0x3f 0x41 ,0x3b 0x40 0x3d 0x3c 0x3b 0x3f 0x3e 0x40 , 0x3f 0x43 0x40 0x3e 0x3c 0x40 0x3d 0x3d ,0x3b 0x3b 0x3e 0x3d 0x40 0x3d 0x3d 0x3c , the write training result: DQS0:0x3d, DQS1:0x30, DQS2:0x3a, DQS3:0x30, min :0x5a 0x5c 0x5d 0x5c 0x53 0x53 0x55 0x5b 0x57 ,0x4e 0x50 0x4c 0x4b 0x53 0x59 0x59 0x5a 0x55 , 0x4b 0x4b 0x55 0x55 0x55 0x55 0x57 0x58 0x57 ,0x4a 0x4c 0x4f 0x49 0x53 0x52 0x53 0x52 0x4e , mid :0x76 0x76 0x78 0x77 0x6a 0x6a 0x6c 0x73 0x6f ,0x6b 0x6a 0x68 0x67 0x6d 0x73 0x73 0x75 0x6f , 0x67 0x63 0x70 0x72 0x6f 0x6d 0x6e 0x6f 0x6f ,0x65 0x63 0x67 0x61 0x6d 0x6d 0x6d 0x6d 0x65 , max :0x92 0x91 0x93 0x93 0x82 0x82 0x84 0x8b 0x88 ,0x88 0x85 0x84 0x84 0x87 0x8d 0x8d 0x90 0x8a , 0x84 0x7c 0x8c 0x90 0x89 0x86 0x86 0x87 0x88 ,0x81 0x7b 0x80 0x7a 0x87 0x88 0x87 0x88 0x7d , range:0x38 0x35 0x36 0x37 0x2f 0x2f 0x2f 0x30 0x31 ,0x3a 0x35 0x38 0x39 0x34 0x34 0x34 0x36 0x35 , 0x39 0x31 0x37 0x3b 0x34 0x31 0x2f 0x2f 0x31 ,0x37 0x2f 0x31 0x31 0x34 0x36 0x34 0x36 0x2f , CA Training result: CONQ., [13.11.2024 10:14] cs:0 min :0x44 0x44 0x3f 0x3c 0x3f 0x3b 0x47 ,0x48 0x41 0x42 0x39 0x41 0x38 0x44 , cs:0 mid :0x82 0x83 0x7c 0x7c 0x7b 0x7b 0x73 ,0x82 0x83 0x7e 0x7a 0x7c 0x79 0x6f , cs:0 max :0xc0 0xc3 0xba 0xbc 0xb7 0xbc 0x9f ,0xbd 0xc5 0xbb 0xbb 0xb8 0xbb 0x9b , cs:0 range:0x7c 0x7f 0x7b 0x80 0x78 0x81 0x58 ,0x75 0x84 0x79 0x82 0x77 0x83 0x57 , cs:1 min :0x41 0x43 0x3c 0x3f 0x3d 0x3a 0x44 ,0x46 0x41 0x3d 0x3c 0x3f 0x3b 0x46 , cs:1 mid :0x82 0x81 0x7b 0x7c 0x7b 0x7a 0x71 ,0x82 0x80 0x7c 0x7b 0x7c 0x7a 0x71 , cs:1 max :0xc4 0xbf 0xbb 0xba 0xba 0xba 0x9f ,0xbf 0xbf 0xbb 0xbb 0xb9 0xba 0x9d , cs:1 range:0x83 0x7c 0x7f 0x7b 0x7d 0x80 0x5b ,0x79 0x7e 0x7e 0x7f 0x7a 0x7f 0x57 , out U-Boot SPL board init U-Boot SPL 2017.09-orangepi (Nov 12 2024 - 22:27:40) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 Trying to boot from MMC2 Card did not respond to voltage select! spl: mmc init failed with error: -95 Trying to boot from MTD2 No misc partition Trying fit image at 0x400 sector ## Verified-boot: 0 ## Checking atf-1 0x00040000 ... sha256(2f01bd8955...) + OK ## Checking uboot 0x00a00000 ... sha256(d82fb13996...) + OK ## Checking fdt 0x00b457b0 ... sha256(5c6babd1aa...) + OK ## Checking atf-2 0xfdcc9000 ... sha256(f1fecab971...) + OK ## Checking atf-3 0xfdcd0000 ... sha256(d7aa45eb18...) + OK Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000) Total: 555.305 ms INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-152-g4e725b15f:cl NOTICE: BL31: Built : 10:51:13, Jul 15 2021 INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: pmu v1 is valid INFO: dfs DDR fsp_param[0].freq_mhz= 1056MHz INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0xa00000 INFO: SPSR = 0x3c9 U-Boot 2017.09-orangepi (Nov 12 2024 - 22:27:40 +0000) Model: Orange Pi 3B PreSerial: 2, raw, 0xfe660000 DRAM: 7.7 GiB Sysmem: init Relocation Offset: ed233000 Relocation fdt: eb9f6470 - eb9fecc0 CR: M/C/I Using default environment failed to find reset-gpios property dwmmc@fe2b0000: 0, dwmmc@fe2c0000: 2, sdhci@fe310000: 1 Device 0: unknown device Card did not respond to voltage select! Card did not respond to voltage select! Device 0: unknown device Device 1: Device 2: SF: Detected sfc_nor with page size 256 Bytes, erase size 4 KiB, total 16 MiB Vendor: 0x2207 Rev: V1.00 Prod: sfc_nor Type: Hard Disk Capacity: 16.0 MB = 0.0 GB (32768 x 512) ... is now current device Bootdev(scan): mtd 2 PartType: EFI DM: v1 boot mode: None I2c0 speed: 100000Hz vsel-gpios- not found! Error: -2 vdd_cpu init 900000 uV PMIC: RK8090 (on=0x10, off=0x00) vdd_logic init 900000 uV vdd_gpu init 900000 uV vdd_npu init 900000 uV io-domain: OK Failed to get scmi clk dev dmc_fsp failed, ret=-19 Model: Orange Pi 3B rockchip_set_ethaddr: vendor_storage_write failed -5 CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A) apll 816000 KHz dpll 528000 KHz gpll 1188000 KHz cpll 1000000 KHz npll 1200000 KHz vpll 24000 KHz hpll 24000 KHz ppll 200000 KHz armclk 816000 KHz aclk_bus 150000 KHz pclk_bus 100000 KHz aclk_top_high 300000 KHz aclk_top_low 200000 KHz hclk_top 150000 KHz pclk_top 100000 KHz aclk_perimid 300000 KHz hclk_perimid 150000 KHz pclk_pmu 100000 KHz Net: eth1: ethernet@fe010000 Hit key to stop autoboot('CTRL+C'): 0 Card did not respond to voltage select! Card did not respond to voltage select! failed to find reset-gpios property CONQ., [13.11.2024 10:14] Device 0: Vendor: 0x126f Rev: S0614B0G Prod: 201907020013 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512) ... is now current device Scanning nvme 0:1... Found U-Boot script /boot/boot.scr Failed to iterate over directory boot ** File not found /boot/boot.scr ** ## Executing script at 00c00000 Wrong image format for "source" command SCRIPT FAILED: continuing... starting USB... Bus dwc3@fcc00000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3@fd000000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device failed to find reset-gpios property ethernet@fe010000 Waiting for PHY auto negotiation to complete......... TIMEOUT ! phy_startup() failed: -110FAILED: -110missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/01-b2-f2-2a-36-55-ae ethernet@fe010000 Waiting for PHY auto negotiation to complete.......user interrupt! phy_startup() failed: -4FAILED: -4missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 ethernet@fe010000 Waiting for PHY auto negotiation to complete.user interrupt! phy_startup() failed: -4FAILED: -4missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 ethernet@fe010000 Waiting for PHY auto negotiation to complete.user interrupt! phy_startup() failed: -4FAILED: -4missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 ethernet@fe010000 Waiting for PHY auto negotiation to complete.user interrupt! phy_startup() failed: -4FAILED: -4missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 ethernet@fe010000 Waiting for PHY auto negotiation to complete.. - Version cloned via armbian during compilation: declare -g BOOTSOURCE="https://github.com/u-boot/u-boot.git" # We ❤️ Mainline U-Boot declare -g BOOTBRANCH="tag:v2024.10" declare -g BOOTPATCHDIR="v2024.10" # Don't set BOOTDIR, allow shared U-Boot source directory for disk space efficiency The problem: Device 0: Vendor: 0x126f Rev: S0614B0G Prod: 201907020013 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512) ... is now current device Scanning nvme 0:1... Found U-Boot script /boot/boot.scr Failed to iterate over directory boot ** File not found /boot/boot.scr ** ## Executing script at 00c00000 Wrong image format for "source" command SCRIPT FAILED: continuing... starting USB... Bus dwc3@fcc00000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3@fd000000: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Suspicions: 1. Too old compilation version at u-boot? 2. Bad forrmating , GPT partitioning ? 3. Old version rkbin (binary devicetree) for orangepi-build-next ? 4. Something else....
November 13, 20241 yr Author I tried using the same tag what in u-boot compilation : but doesn't work: I would have to go deep to change it.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.