Hi all,

 

I bought this ethernet:

 

 

 

The idea is connect to the SPI, but not sure what pines i must to connect...

 

i follow this: Raspi.tv

 

So i connect the pines, exactly like there say, but he connect on the UART not in the SPI :S (have  2 pines more, but the pines that he conenct i have in my ethernet board)

 

 

So i connect to the gpio of my board and well turn on! yeah! xD:

 

If i fo ifconfig i see this:

root@bananapim2:~# ifconfig
bond0     Link encap:Ethernet  HWaddr 7e:99:6b:7c:04:39
          UP BROADCAST MASTER MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0   TX bytes:0 (0.0 

eth0      Link encap:Ethernet  HWaddr 02:44:07:0d:76:33
          inet addr:192.168.1.44  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::44:7ff:fe0d:7633/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:937 errors:0 dropped:0 overruns:0 frame:0
          TX packets:459 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:758921 (741.1 KiB)  TX bytes:86608 (84.5 KiB)
          Interrupt:44

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:70 errors:0 dropped:0 overruns:0 frame:0
          TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:31817 (31.0 KiB)  TX bytes:31817 (31.0 KiB)

wlan1     Link encap:Ethernet  HWaddr 98:3b:16:c8:56:6e
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:42 errors:0 dropped:42 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:12820 (12.5 KiB)  TX bytes:0 (0.0 

1. I should supposed is the bond0 the interface?? ot should be the an eth1?
2. Can i connect this to the SPI?
3. Its enabled SPI on armbian by defaultt?
4. Where is the file that i must change for work with GPIO on Armbian? its /boot/config-4.3.3-sunxi? there are a lot of lines that have SPI options, to many with "=m" and others comments :S

 

I try edit /etc/networks/interfaces and put auto bon0, but not get any IP address, i haven't got any idea about wtf means bond0...

Luckily your first image name contains "28j60", so we can say that it's an enc28j60 module.

Linux driver for this is in \drivers\net\ethernet\microchip\enc28j60.c, and required kernel option is CONFIG_ENC28J60,

Unfortunately it's not enabled by default in Armbian kernel.

 

For compiling your own kernel please read the documentation here or wait for a new kernel release (I'll enable this module if I don't forget).

/boot/config-4.3.3-sunxi?

 

Please keep two things in mind:

• Banana Pi M2 is no Raspberry Pi. On Raspberry Pi /boot/config.txt has a special meaning, with Armbian a file called /boot/config-4.3.3-sunxi is something completely different! (important to note when you rely on tutorials written for RPi)
• The Ethernet module you try to use is both slow as hell and power hungry. I would check whether it's ok to draw 160mA from the 3.3V pin

Any USB-to-Ethernet adapter is a better choice when you have a free USB port.

Please keep two things in mind:

• Banana Pi M2 is no Raspberry Pi. On Raspberry Pi /boot/config.txt has a special meaning, with Armbian a file called /boot/config-4.3.3-sunxi is something completely different! (important to note when you rely on tutorials written for RPi)
• The Ethernet module you try to use is both slow as hell and power hungry. I would check whether it's ok to draw 160mA from the 3.3V pin

Any USB-to-Ethernet adapter is a better choice when you have a free USB port.

 

Yeah i know, but i biught this because its cheap for testing, i wanna buy an Ethernet 10/100/1000 to connect to the SPI, i dont wanan connect in the usb...

 

Luckily your first image name contains "28j60", so we can say that it's an enc28j60 module.

Linux driver for this is in \drivers\net\ethernet\microchip\enc28j60.c, and required kernel option is CONFIG_ENC28J60,

Unfortunately it's not enabled by default in Armbian kernel.

 

For compiling your own kernel please read the documentation here or wait for a new kernel release (I'll enable this module if I don't forget).

 

 

Thanks, I will try this week, anyway, when this new kernel release will come??

i wanna buy an Ethernet 10/100/1000 to connect to the SPI

 

This will be most likely the slowest GbE implementation in the world. Have you checked the state of drivers already? http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229951.html

In 1-2weeks.

 

https://github.com/igorpecovnik/lib/commit/2a072de9d81ebd0cf3b33de1e006ffb6ca6b56ea

In 1-2weeks.

 

And then it's time to start whining: https://github.com/torvalds/linux/blob/master/drivers/spi/spi-sun6i.c  (still no DMA so good luck when every single bit needs seconds being handed over the wires )

This will be most likely the slowest GbE implementation in the world. Have you checked the state of drivers already? http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229951.html

 

Wow... is a sith... i will open  a new topic because i start to have a lot of problems trying to adding new hardware to the arm boards, thanks for the info

 

Update: Here my new post: http://forum.armbian.com/index.php/topic/663-hardware-question-gpio-spi-uart-wireless-ethernet/