Hi all!

First time poster, i apologize in advance for any etiquette violations...

 

I have an OrangePi Zero H2+ board and the DS18B20 sensor (waterproof version).

 

I have soldered the pullup resistor between power and data cables.

 

I have Armbian Stretch 5.83 with  4.19.38-sunxi kernel.

 

I have enabled the w1-gpio overlay and loaded the w1-therm driver.

 

Data is on PD14 (GPIO 10), power is on 5v (tried also on 3.3v)

 

I can see this in my dmesg:

[   10.371825] w1_master_driver w1_bus_master1: w1_search: max_slave_count 64 reached, will continue next search.
[   58.171052] w1_master_driver w1_bus_master1: Attaching one wire slave 00.800000000000 crc 8c
[   58.183072] w1_master_driver w1_bus_master1: Family 0 for 00.800000000000.8c is not registered.
[  118.047572] w1_master_driver w1_bus_master1: Attaching one wire slave 00.400000000000 crc 46
[  118.055622] w1_master_driver w1_bus_master1: Family 0 for 00.400000000000.46 is not registered.
[  165.855415] w1_master_driver w1_bus_master1: Attaching one wire slave 00.c00000000000 crc ca
[  165.859633] w1_master_driver w1_bus_master1: Family 0 for 00.c00000000000.ca is not registered.
[  237.774053] w1_master_driver w1_bus_master1: Attaching one wire slave 00.200000000000 crc 23
[  237.790557] w1_master_driver w1_bus_master1: Family 0 for 00.200000000000.23 is not registered.
[  297.625355] w1_master_driver w1_bus_master1: Attaching one wire slave 00.a00000000000 crc af
[  297.631722] w1_master_driver w1_bus_master1: Family 0 for 00.a00000000000.af is not registered.
[  333.371600] w1_master_driver w1_bus_master1: Attaching one wire slave 00.600000000000 crc 65
[  333.379481] w1_master_driver w1_bus_master1: Family 0 for 00.600000000000.65 is not registered.
[  371.005370] w1_master_driver w1_bus_master1: Attaching one wire slave 00.e00000000000 crc e9
[  371.014569] w1_master_driver w1_bus_master1: Family 0 for 00.e00000000000.e9 is not registered.
[  430.421257] w1_master_driver w1_bus_master1: Attaching one wire slave 00.100000000000 crc 9d
[  430.428462] w1_master_driver w1_bus_master1: Family 0 for 00.100000000000.9d is not registered.
[  467.081328] w1_master_driver w1_bus_master1: Attaching one wire slave 00.900000000000 crc 11
[  467.095848] w1_master_driver w1_bus_master1: Family 0 for 00.900000000000.11 is not registered.

 

And it just goes on and on.

 

Under /sys/bus/w1/devices i can see the device (which changes over time) but there is no w1_slave file inside to read...

 

Am i doing something wrong or the sensor is faulty?

 

thank you in advance for your support!

 

21 minutes ago, shimitar said:

First time poster

When you ask for tips always provide 

armbianmonitor -u

I (and many others) am using this sensor (on H5 based board) and it works fine. What is the content of /boot/armbianEnv.txt ?

My /boot/armbianEnv.txt:

verbosity=1
logo=disabled
console=serial
disp_mode=1920x1080p60
overlay_prefix=sun8i-h3
overlays=usbhost2 usbhost3 w1-gpio
rootdev=UUID=a974851a-d7f7-46a1-9c1a-3a66d31e8f7b
rootfstype=ext4
param_w1_pin=PD14
param_w1_pin_int_pullup=0
usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:

 

The armbianmonitor -U output is here (board is not connected to internet):

http://www.gardiol.org/mon

 

As additional notes, i use DHT22 sensors on other H2+ boards with no issue, this is my first time with the DS18B20

2 hours ago, shimitar said:

this is my first time with the DS18B20

We've seen this symptom in the past where CPU frequency was relevant since W1-GPIO is done in software, so check the MIN_SPEED in your /etc/default/cpufrequtils, it should be at least 480000, but you can try higher.

 

I had this:

_enabled

# WARNING: this file will be replaced on board support package (linux-root-...) upgrade
ENABLE=true
MIN_SPEED=480000
MAX_SPEED=1400000
GOVERNOR=interactive

 

i am now tyring this:

# WARNING: this file will be replaced on board support package (linux-root-...) upgrade
ENABLE=true
MIN_SPEED=1400000
MAX_SPEED=1400000
GOVERNOR=interactive

 

Of course did a /etc/init.d/cpufrequtils restart

 

 

.... but seems nothing has changed

Should I use a special pin for the data or any io should do? Specially, the default PD14 is confirmed working?

 

24 minutes ago, shimitar said:

Specially, the default PD14 is confirmed working?

 

5 hours ago, shimitar said:

Data is on PD14 (GPIO 10)

This is maybe why it is not working ...

Did you check the schematic ?

There is no PD14 on OPiZero ! PD14 is the IO1 on OPiPC ... On OPiZero, IO1 is PA7, but you can also use other pins, but you need to adapt /boot/armbianEnv.txt accordingly ...

Could you please provide a link to an image which explains the names of all the pins on the board for the opi zero h2+?

 

Because I'm confused... Any pin seems to have many different names... And it seems to me that the PD14 should be the bottom-right one (opposite to the 5v pin in the internal row).... But meybe I am looking to the wrong pin out?

6 minutes ago, shimitar said:

Could you please provide a link to an image which explains the names of all the pins on the board for the opi zero h2+?

http://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port

6 minutes ago, shimitar said:

And it seems to me that the PD14 should be the bottom-right one

As I said, there is no PD14 on OPiZero ... Look again to schematic : https://linux-sunxi.org/File:Orange-Pi-Zero-Schanetics-v1_11.pdf

Yes! That was it! I had to change the pin name to PA10... Thank you for the schematics, I will treasure them...

 

Solved!