Good day,

for my Orangepi PC+ I installed Armbian Ubuntu Jammy on a µSD card. Up until Armbian Ubuntu Strech I was able to use a PCM510A for sound output. The settings for this were easy. With all updated OS after Strech, I can't install the PCM. Unfortunately, the help that was published in the forum wasn't helpful or I couldn't take it over. On the eMMC I have installed Armbian5.59 Orangepipcplus Ubuntu xenial default 3.4.113 desktop. Because of the advanced age of this OS, there are no updates and upgrades. Luckily my internet radio still works.

Can someone explain to me how I can install the PCM510A at Jammy?

Kind regards

hajupiko49

No idea if this is possible with mainline if that needs vendor adjustments. Make sure to read here to understand why

https://docs.armbian.com/User-Guide_FAQ/#why-does-hardware-feature-xy-work-in-old-kernel-but-not-in-more-recent-one

@hajupiko49It should work!

Read this tread "https://forum.armbian.com/topic/9009-info-friendlyarm-pcm5102a-hat-with-nanopi-neo-under-mainline-4xx-and-dev-5xx/"

(Thanks Guido)

 

I dit it on a Orangepi-Plus with bullseye, kernel 5.15.

 

Use this steps:

sudo apt update && sudo apt upgrade -y
freeze updates in armbian-config dtb

 

Than you can begin changeing your dtb.

You have only to replace "sun8i-h3-orangepi-plus" to your needs..

 

Spoiler

 

hers ny notes:

 

- Sound i2s ---

h3-sound-overlay

OrangePiPlus

BCK        -> PA19 (27) black
LRCK    -> PA18 (28) red
DATA    -> PA20 (37) white
GND        -> PA18 (34) yellow

MCLK wird nicht benötigt!

--- Expansion Port ---

GPIO

#---------------------------------------------------------------------------------------#
|\/ Makierung bei 1    | Oben          Orange Pi | PC | PC+ | Plus                            |
+---------------------------------------------------------------------------------------+
| 1  | 3.3V                                  | 2  | 5V                                    |
| 3  | PA12 (TWI0_SDA/DI_RX/PA_EINT12)         | 4  | 5V                                    |
| 5  | PA11 (TWI0_SCK/DI_TX/PA_EINT11)         | 6  | GND                                    |
| 7  | PA6  (SIM_PWREN/PWM1/PA_EINT6)         | 8  | PA13 (SPI1_CS/UART3_TX/PA_EINT13)    |
| 9  | GND                                     | 10 | PA14 (SPI1_CLK/UART3_RX/PA_EINT14)    |
| 11 | PA1  (UART2_RX/JTAG_CK/PA_EINT1)     | 12 | PD14                                    |
| 13 | PA0  (UART2_TX/JTAG_MS/PA_EINT0)     | 14 | GND                                    |
| 15 | PA3  (UART2_CTS/JTAG_DI/PA_EINT3)     | 16 | PC4                                    |
| 17 | 3.3V                                 | 18 | PC7                                    |
| 19 | PC0  (SPI0_MOSI)                     | 20 | GND                                    |
| 21 | PC1  (SPI0_MISO)                        | 22 | PA2  (UART2_RTS/JTAG_DO/PA_EINT2)    |
| 23 | PC2  (SPI0_CLK)                         | 24 | PC3  (SPI0_CS)                        |
| 25 | GND                                     | 26 | PA21 (PCM0_DIN/SIM_VPPPP/PA_EINT21)    |
| 27 | PA19 (PCM0_CLK/TWI1_SDA/PA_EINT19) * | 28 | PA18 (PCM0_SYNC/TWI1_SCK/PA_EINT18) *|
| 29 | PA7  (SIM_CLK/PA_EINT7)                 | 30 | GND                                    |
| 31 | PA8  (SIM_DATA/PA_EINT8)             | 32 | PG8  (UART1_RTS/PG_EINT8)            |
| 33 | PA9  (SIM_RST/PA_EINT9)                 | 34 | GND                                    |
| 35 | PA10 (SIM_DET/PA_EINT10)             | 36 | PG9  (UART1_CTS/PG_EINT9)            |
| 37 | PA20 (PCM0_DOUT/SIM_VPPEN/PA_EINT20 *| 38 | PG6  (UART1_TX/PG_EINT6)                |
| 39 | GND                                     | 40 | PG7  (UART1_RX/PG_EINT7)                |
+---------------------------------------------------------------------------------------+
|                    Unten                    \/                                            |
+---------------------------------------------------------------------------------------+
| 2xUSB |                       LAN         |  1xUSB                                      |
#---------------------------------------------------------------------------------------#

/boot/dtb/sun8i-h3-orangepi-plus.dtb

-

sudo cp /boot/dtb/sun8i-h3-orangepi-plus.dtb /boot/dtb/sun8i-h3-orangepi-plus.dtb_org

sudo dtc -I dtb -O dts /boot/dtb/sun8i-h3-orangepi-plus.dtb -o /boot/dtb/sun8i-h3-orangepi-plus.dts

sudo nano /boot/dtb/sun8i-h3-orangepi-plus.dts

okay

        i2s@1c22000 {
            #sound-dai-cells = <0x00>;
            compatible = "allwinner,sun8i-h3-i2s";
            reg = <0x1c22000 0x400>;
            interrupts = <0x00 0x0d 0x04>;
            clocks = <0x03 0x38 0x03 0x54>;
            clock-names = "apb\0mod";
            dmas = <0x1a 0x03 0x1a 0x03>;
            resets = <0x03 0x2b>;
            dma-names = "rx\0tx";
            status = "okay";
            phandle = <0x66>;
        };

sudo dtc -I dts -O dtb /boot/dtb/sun8i-h3-orangepi-plus.dts -o /boot/dtb/sun8i-h3-orangepi-plus.dts_I2S_okay

sudo cp /boot/dtb/sun8i-h3-orangepi-plus.dts_I2S_okay /boot/dtb/sun8i-h3-nanopi-neo.dtb

sun8i-h3-I2S-out.dts nach /home/master kopieren...

sudo armbian-add-overlay sun8i-h3-I2S-out.dts

sudo reboot

---

sudo nano /etc/asound.conf

pcm.sftvol {
    type            softvol
    slave.pcm       "plughw:1"
    control {
        name        "PCM"
        card        1
    }
}

pcm.!default {
    type             plug
    slave.pcm       "sftvol"
}

ctl.!default {
    type hw
    card 1
}

speaker-test -D default -c 2 -twav

 

you should here some noise  on your speakers..

 

Best wishes

 

Markus