November 30, 20232 yr Suddenly after updating via armbian-config I lost ssh access and found the port closed. I rewrote the latest armbian version, stuck the sd card in, connected to ethernet cable via router and started up. The red and green lights were on as they should be and the internet cable was flashing green. Waited 3 minutes and checked the ports with nmap. And the port is closed again. Not responding to ping at all. I am still new to this topic. Please help and sorry if the translator translates crookedly.
December 8, 20232 yr Sorry if this comes off as obvious or unhelpful... but if it were me I would hook up HMDI + USB KB real quick just to verify that the board was fully coming online.
December 9, 20232 yr Author Thanks for the answer. I'll give it a try. I do not have such an adapter, but I will buy it Edited December 9, 20232 yr by Flops
December 9, 20232 yr Author In addition I want to say that when I tried to run armbian with usb ethernet started to light up and orange light. I am still waiting for the adapter to be delivered Edited December 9, 20232 yr by Flops
December 18, 20232 yr Author I bought a uart and connected it according to the instructions in the video. I used screen and set the speed to 1500000 but the terminal shows only garbage. Maybe I should set a different speed?
December 18, 20232 yr 5 minutes ago, Flops said: CP2102 Good enough for allwinner but too slow for AML or RK. Get a proper one. 1500000 is the correct speed. If the chip cannot handle it you obviously get an error or garbage.
December 18, 20232 yr Author ok. I forgot to look. All right, I'll buy a proper adapter. Can you recommend an adapter or tell me where to look? Edited December 18, 20232 yr by Flops
December 18, 20232 yr aliexpress, amazon, ebay,.... all of those should have some proper ones. For recommended chips please refer to the video mentioned above.
January 14, 20242 yr Author I bought a uart and connected it as indicated in the video. The text is already readable, but sometimes it underwrites and moves away. What should I do next? Modified: it does not output correctly what I enter. Is there any way to improve it? Edited January 14, 20242 yr by Flops
January 14, 20242 yr Author Saw this in the logs: INFOx4000001 != 0xfead0003 ERROR: INFO: BL31: Initializing Excervices WARNING: No OPTEE providon. SMC`s destined for OPTEE wil (eMMC) Maybe it means something?
January 14, 20242 yr Author The system boots from the sd card and correctly. sshd is also active. Strange... Edited January 14, 20242 yr by Flops
January 15, 20242 yr Author It can work via uart, sshd works and yet it does not respond to a ping or ssh connection. At the same time it can connect to the internet and download packets by itself.
February 3, 20242 yr Author I tried rebooting the router. Nothing changed in the end. The router does not respond to ping, but the board works properly via uart. Please help
February 3, 20242 yr So when UART works you can use armbianmonitor -U to print debug output to serial and then use a pastebin service of your choice to share the whole output.
February 3, 20242 yr Author Could you tell me how to conveniently transfer logs to a text file, because the terminal floats when scrolling?
February 4, 20242 yr 1468 ### ip addr: 1469 p default qlen 1000 1471 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 1472 inet XXX.XXX.0.1/8 scope host lo 1473 valid_lft forever preferred_lft forever 1474 inet6 ::1/128 scope host noprefixroute 1475 valid_lft forever preferred_lft forever ult qlen 1000 1477 link/ether 6e:48:1c:02:bd:e7 brd ff:ff:ff:ff:ff:ff 1478 Either the logs are incomplete or the ethernet ports don't show up at all. Odd...
February 4, 20242 yr Author When I connected to cable and uart it was able to update and download packages. I will try to copy the log again today. And I'll also check ifconfig Edited February 4, 20242 yr by Flops
February 4, 20242 yr Author 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host noprefixroute valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 2a:77:33:98:ba:5a brd ff:ff:ff:ff:ff:ff inet 192.168.0.108/24 brd 192.168.0.255 scope global dynamic noprefixroute end1 valid_lft 7145sec preferred_lft 7145sec inet6 fe80::8a87:d850:159c:a59e/64 scope link noprefixroute valid_lft forever preferred_lft forever This is what the ip a gave me when I plugged in the cable. Edited February 4, 20242 yr by Flops
February 21, 20242 yr Author When scanning the network via arp-scan it still writes (Unknown: locally administered).
February 25, 20242 yr Author Solution Anyway, as it turns out I didn't have "local access" enabled in the access point settings. LOL
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.