SBC News

Description ArmSoM Sige3 is rk3568 version of the sige series boards. It is a board supporting pd negotiation with fusb302, so I add pd negotiation in uboot. This pr depends on https://github.com/armbian/linux-rockchip/pull/236 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh BOARD=armsom-sige3 BRANCH=vendor BUILD_MINIMAL=no DEB_COMPRESS=xz KERNEL_CONFIGURE=no RELEASE=noble KERNEL_GIT=shallow BUILD_DESKTOP=yes DESKTOP_APPGROUPS_SELECTED= DESKTOP_ENVIRONMENT=gnome DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base Checklist: Please delete options that ar…

Description Radxa E52C is a rk3582 based board with dual 2.5G ethernet. This pr depends on https://github.com/armbian/linux-rockchip/pull/203. Since its soc is rk3582 so it should the same uboot patch from rock-5c to enable good ip cores disabled by u-boot. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh BOARD=radxa-e52c BRANCH=vendor BUILD_MINIMAL=no DEB_COMPRESS=xz KERNEL_CONFIGURE=no RELEASE=noble KERNEL_GIT=shallow BUILD_DESKTOP=no [x] Board boots fine. Checklist: Please delete options that are not relevant. [x] My code follows the style g…

Description Heltec HT-M2808 Helium Miner. RK3328 https://heltec.org/project/ht-m2808/ How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh build BOARD=rk3328-heltec BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=no EXPERT=yes KERNEL_CONFIGURE=yes KERNEL_GIT=shallow RELEASE=bookworm [x] Tested on both current and edge [x] Flash via RKDeveloptool using rk3328_loader_ddr333_v1.16.250.bin bootloader Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-revi…

Description Add new borad of ASUS Tinker-Edge-R. ASUS Tinker Edge R is an Single Board Computer (SBC) specially designed for AI applications. I've written the device tree file for it, added the u-boot config file, and I've done the current version adaptation. Jira reference number [AR-9999] How Has This Been Tested? [x] UART test. The serial port output is printed through UART, and there are almost no errors in the armbian boot log. [x] Stability testing. Let the CPU run the specified task all the time, and the test will be conducted for 48 hours without any error. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review …

Description Since latest changes to the partition handling we need to add new dependency to the build host & docker as builds are failing. Jira reference number AR-1332 How Has This Been Tested? [x] Starting from a clean Docker image Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

No descriptionView the full article

Add new rockchip cpu rk3528 support,and new board H28K support. This commit requires: https://github.com/armbian/rkbin/pull/23 Rockchip RK3528 preliminary specifications: CPU – Arm Cortex-A53 processor (4 core 2.0ghz ) GPU – Arm Mali-450 GPU with AFBC compression support Memory – LP4, LP4X, LP3, DDR4, DDR3 HDMI 2.0 Up to 8Kp25 Video decoding – Up to 8Kp25 PCIE2.0/USB3.0 H28K board specifications: 2/4GB LPDDR4 8/32GB EMMC 5.0 two Gb ethernet(one gmac one pcie eth) type C USB2.0(support PD power and maskrom) type A USB2.0 View the full article

Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] Documentation summary for feature / change Add new user to render group, otherwise the non-root user do not have access /dev/dri/renderD128 on RK3399. When login using non-root user to the desktop environment, the GPU acceleration does not work. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Test A Login to the desktop environment using non-…

Description Next Ubuntu (not LTS) Jira reference number AR-1380 How Has This Been Tested? [x] Build CLI and minimal images [x] Build desktop (our repository needs to be updated due to missing package) Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description Building for mangopi mq crashes with the following error: Image 'itb' is missing external blobs and is non-functional: opensbi /binman/itb/fit/images/opensbi/opensbi (fw_dynamic.bin): See the documentation for your board. The OpenSBI git repo is at https://github.com/riscv/opensbi.git You may need to build fw_dynamic.bin first and re-build u-boot with OPENSBI=/path/to/fw_dynamic.bin Some images are invalid make: *** [Makefile:1124: .binman_stamp] Error 103 --> (179) ERROR: Error 2 occurred in main shell [ at /armbian/lib/functions/logging/runners.sh:211 run_host_command_logged_raw() --> lib/functions/lo…

Description We call ssh-keygen when building with CRYPTROOT=yes, but openssh-client is not mentioned into EXTRA_BUILD_DEPS in extensions/fs-cryptroot-support.sh which can make the build to fail. This PR fixes the same How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [X] Created a build with CRYPTROOT=yes and ARTIFACT_IGNORE_CACHE=yes and made sure it no longer fails because of missing ssh-keygen in docker image Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, parti…

Description The BUILD_ONLY option can be set as a comma separated list of build artifact names to filter build artifacts being compiled. The following artifact names are supported: u-boot, kernel, armbian-config, armbian-zsh, plymouth-theme-armbian, armbian-firmware, armbian-bsp, chroot, bootstrap GH issue reference #4421 Test Results Following tests have been performed with the according output: [x] Test 1 - U-Boot only build - BUILD_ONLY="u-boot": ./compile.sh BOARD=cubietruck BRANCH=current RELEASE=focal BUILD_MINIMAL=yes BUILD_DESKTOP=no BUILD_ONLY="u-boot" KERNEL_ONLY=no KERNEL_CONFIGURE=no COMPRESS_OUTPUTIMAGE=sha,gpg,7z ... MKIMAGE u-boot.img MKIMAGE u-bo…

Description This probably can help solve the usecases that require home directory to stay present in the final image like the one mentioned in #5918 Jira reference number AR-1912 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [X] Tested creating image with and without the INCLUDE_HOME_DIR=yes. Works as expected. Checklist: [X] My code follows the style guidelines of this project [X] I have performed a self-review of my own code [X] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [X]…

Description Board info: http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-3B.html Devicetree and uwe5622 driver is in this pr: https://github.com/armbian/linux-rockchip/pull/88 I've written a mainline devicetree but since we are bumping rockchip64-edge to 6.5, I will add it later. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] legacy build success [x] legacy build boot fine on opi3b Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my …

Description Add uarts dts as per vendor spec How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Built orangepi5-plus with kernel 6.8 and connected serial gps to uart3-m1 ttyS3 - got a fix Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] My changes generate no new warnings View the full article

Description This overlay enable 7″ lcd(https://pine64.com/product/7-lcd-touch-screen-panel/) on rockpro64 linux 6.x How Has This Been Tested? I haven't a rockpro64,but it was tested in there https://forum.armbian.com/topic/21528-possible-to-get-jammy-515-kernel-to-use-dsitp-display/?do=findComment&comment=157010 Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream …

Description Noticed this small utils is missing. Lets add it. How Has This Been Tested? [x] Installed on target Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description There is a userspace panfrost mesa driver for mali g610, and I made a ppa for it: https://launchpad.net/~liujianfeng1994/+archive/ubuntu/panfork-mesa. So I add a appgroup for jammy desktop. How Has This Been Tested? There is already a working out of box image: https://github.com/amazingfate/armbian-rock5b-images/actions/runs/3509051670/jobs/5877885694. [x] Build jammy gnome image successfully. [x] Image with panfork working out of box on my rock5b. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corre…

Description This allows to use ssd sata on pci in orange pi 5 Make sure you add overlays=opi5-sata to /boot/armbianEnv.txt if you have a sata drive How Has This Been Tested? Tested with local armbian build and sata m2 ssd, can list and use sata ssd Thanks @efectn for the support View the full article

Description Patches needed to run Pi-KVM. Jira reference number AR-1300 How Has This Been Tested? [x] Build CURRENT and EDGE [x] Tested by (srepac) Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description Add plymouth package to base images except minimal Jira reference number AR-1377 How Has This Been Tested? [x] Build minimal [x] Build CLI Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description UEFI installer. Help is needed for reworking this tool into something less fragile. Jira reference number AR-1355 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Windows 11 laptop. Shrink main partition, then generate new partition from that space and format it. Then run nand-sata-install Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My chang…

Description Add a link to the page, where anyone can book a meeting with us. Non commercial cooperation type and professional consultation. temporally removing link to subscriptions as its not finished yet. Jira reference number MAN-114 How Has This Been Tested? [x] We are using this internally for awhile. Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream module…

Description Add pwm fan support to NanoPi R4S. Document from FriendlyElec: https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#How_to_Control_Fan_Speed_for_Cooling And reference code: https://github.com/friendlyarm/kernel-rockchip/commit/f74ac319f02e2d22cdd33227e7f167e4232809f9 How Has This Been Tested? build and run on R4SE hardware. [x] fan works [x] /sys/devices/virtual/thermal/thermal_zone0/trip_point_[3/4]_temp controls two speed of the fan Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding …

Description Adds the Radxa E20C board, which is based on the Rockchip RK3528 SoC. U-Boot config from https://github.com/radxa/u-boot/commit/5202c429714e34dcaeb6ea2a76822fb8447e1409 Depends on https://github.com/armbian/linux-rockchip/pull/231 (which, as of writing, is not merged) How Has This Been Tested? [x] Boots (from microSD) [x] USB serial via debug port works (see note) [x] LAN port works (RK3528 Ethernet) [x] WAN port works (RTL8168 Ethernet) [x] Debug USB-C port works (can run USB gadgets) [x] USB-A port works (can use USB devices) [x] User button works (via /dev/input/event0) [x] LED control works (via /sys/class/leds) [x] eMMC access works Not tested: RKMPP…

Description CSC build target. Untested, no hardware. Jira reference number AR-1301 How Has This Been Tested? [x] Build test Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description The Recore dts patch submitted earlier was not applied since the patch was not not referenced in the series.conf file. The patch adds it to the list. Documentation summary for feature / change [x] short description (copy / paste of PR title) [x] summary (description relevant for end users) [ ] example of usage (how to see this in function) How Has This Been Tested? It has been tested on the following hardware: [x] Recore A8 Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand area…

Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Test A [ ] Test B Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no ne…

Description Add missing files. Jira reference number AR-1578 How Has This Been Tested? [x] Build test of related hardware Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

RK3328 UART1 and I2C0 are available on Orange Pi R1 Plus LTS 13 pin connector. Add device tree overlay files for rk3328 uart1 and i2c0. I have noticed chatter on Github (@rpardini) around dtbo naming conventions. I'm therefore not absolutely clear on what is expected. Historic dtbo's for rk33xx are formatted with a rockchip prefix (there are some exceptions). I've used the rockchip prefix: rockchip-rk3328-i2c0.dtbo rockchip-rk3328-uart1.dtbo And the "Hardware" selection in armbian-config displays them correctly without the prefix. Jira reference number AR-1509 [x] Builds correctly and produces the dtbo's [x] Tested that the "Hardware" can be selected via armbian-…

Follow-up from #4286. View the full article

Follow-up from #4286 & #4309. View the full article

Description These patches are are needed for panfork "go-faster". Using env PAN_MESA_DEBUG=gofaster we can get better glmark performance. Here are some infos from icecream95 copied on discord: "go-faster" patches for Mesa on RK3588 are almost ready, but need some kernel patches to get the full advantage: https://gitlab.com/panfork/rk3588-implicit-sync That repo has backports of a couple of patches from Linux v6.0, a fix to rockchip-drm, and also a patch to kbase fixing a bug that I hit accidentally… but could probably be used in an exploit. On that note, kbase vulnerabilities are found quite often: https://developer.arm.com/Arm Security Center/Mali GPU Driver Vulnerabi…

Description Devicetree is already in https://github.com/armbian/linux-rockchip so just a board config is enough How Has This Been Tested? [x] ./compile.sh BOARD=rock-5-itx BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=no DEB_COMPRESS=xz KERNEL_CONFIGURE=no RELEASE=bookworm KERNEL_GIT=shallow, flashed to emmc and boot Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules Vie…

Description Add rockchip drivers to the uefi-arm64 kernel config to be able to use https://github.com/jaredmcneill/quartz64_uefi on some rk3566/rk3568 boards. How Has This Been Tested? Booted a Pine SOQuartz/CM4IO board with the EDK2 bootloader mentioned above on a sdcard and the patched generic uefi-arm64 image on an nvme drive. Tested with ACPI and Devicetree. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent change…

Description Z96a is a cloud laptop designed by Sunniwell.co from China, using rk3568b2 chip, 4g memory, 32g emmc, 1080p screen. Because of the manufacturer's special design, such as power chip rk817 etc.. drivers needs to be patched, so a new board family needs to be created. After creating a new board family, Added code will not affect the armbian historical or other boards. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Test A: Image which compiled by new code has been flashed in z96a, and everything works fine. Checklist: [x] My code follows the st…

Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ ] Test A [ ] Test B Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no ne…

Description Most chips support 2.2GHZ as maximum freq. Needs some voltage overclock to get 2.35-2.4GHz speeds. Looks like 50 mV enough to get this speeds. Note: Doesn't have much performance improvement. It provides better performance to disable DMC and changing governors. How Has This Been Tested? [x] Tested on OPi 5. Seems stable Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and publis…

Description As discussed here on the forums this overlay adds support for the RTL8211f chip found on Rockpi E Hardware revision 1.21 Documentation summary for feature / change Documentation updated, hope that's enough and appropriate. How Has This Been Tested? Running that overlay currently on four Rockpi S instances connected to the 1 Gbit/s port Checklist: [X] I have performed a self-review of my own code [X] My changes generate no new warnings View the full article

Description Other devices could be added if whatever the regulator needed for UHS is enabled. Read perf def improved on the gnome disk benchmarks. Jira reference number [AR-9999] let's enable salva's UHS overlay for RK3399 tested on PBP with 2ghz with 64 gig samsung evo select i like using the yabs.sh fio benchmark for mixed r/w tests curl -sL yabs.sh | bash -s -- -i -g -n also did gnome disk utility read benchmark before kernel 6.6.10 yabs # ## ## ## ## ## ## ## ## ## ## ## ## ## ## ## ## ## # # Yet-Another-Bench-Script # # v2024-01-01 # # https://github.com/masonr/yet-another-bench-script # # ## ## …

Description Fixes meson64 current & edge kernels. Add patch https://patchwork.kernel.org/project/linux-amlogic/patch/d9721029-780e-09f1-0207-72d3897032a4@gmail.com/ The usage of edge-triggered interrupts lead to lost interrupts under load, see [0]. This was confirmed to be fixed by using level-triggered interrupts. The report was about SDIO. However, as the host controller is the same for SD and MMC, apply the change to all mmc controller instances. [0] https://www.spinics.net/lists/linux-mmc/msg73991.html Fixes: 1499218c80c9 ("arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi") Reported-by: Peter Suti <peter.suti@streamunlimited.com> Te…

Description When generating KDE desktop environment beyond Jammy, some essential items are missing like systemsettings. The plasma-discover package manager was also missing. In bookworm, some gname packages are also not available any more and have been removed. Jira reference number AR-1897 How Has This Been Tested? [ ] Generated a uefi_x86 version for current/bullseye/KDE and testing in in VirtualBox [ ] Generated a uefi_x86 version for current/bookworm/KDE and testing in in VirtualBox View the full article

Description Low hanging fruit.. Add bash shebang at the start of all .sh files Jira reference number AR-1406 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ ] Test A [ ] Test B Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full artic…

Description We don't have any and for Ubuntu variant recently was added. Jira reference number AR-1324 View the full article

Description This PR adds support for the Texas Instruments SK-AM68 and SK-AM69 boards. Notable features of SK-AM68 board: 16GB LPDDR4‐4266 with support for inline error correction code (ECC) DisplayPort 4K resolution with MST support and HDMI Two CSI-2 ports compatible with Raspberry Pi 8 TOPS deep-learning performance and hardware-accelerated edge AI Three USB 3.0 Type A ports, one USB 3.0 Type C port Gigabit Ethernet and 4x CAN-FD Headers One M.2 key M connector Notable features of SK-AM69 board: 32GB LPDDR4‐4266 with support for inline error correction code (ECC) DisplayPort 4K resolution with MST support and HDMI Three CSI-2 ports compatible with Raspberry Pi 32…

Description Add some China mirrors for Ubuntu amd64 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [X] Build Checklist: [ ] My code follows the style guidelines of this project [X] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [X] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Needs firmware for ap6275p -> https://github.com/armbian/firmware/pull/47 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ ] Test A [ ] Test B Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Add Firefly Station M3 Tested, work all equipment View the full article

Description We need at least one build target in the family & it doesn't need to build image. View the full article

Description If we will be shipping firmware frozen by default, we need to warn and provide information how to update kernel. Armbian-config needs to be adjusted too. Cron job is generating numbers of packages that needs to be updated. This numbers is displayed in MOTD, when > 0. Since we want to know which packages are on hold, we need to know if kernel packages are on hold when upgrade is finished, fix numbers and update list Jira reference number AR-1375 How Has This Been Tested? [x] Manual run Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in har…

Description Add support for armsom-sige7 board Dependencies required for this change：https://github.com/armbian/linux-rockchip/pull/131 armsom-sige7 related document links: How Has This Been Tested? Compile command: ./compile.sh 2.5Gb Network *2 ok Headphone ok usb 3.0 * 2 ok typec ok hdmi tx ok 40pin-Header ok LED ok debug ok Fan ok M2 E key ok Checklist: [√ ]My code follows the style guidelines of this project [√ ]I have performed a self-review of my own code [√ ]I have commented my code, particularly in hard-to-understand areas [√ ]I have made corresponding changes to the documentation [√ ]My changes generate no new warnings [√ ]Any dependent changes have been mer…

Description Add support for BigTreeTech CB1 (Allwinner H616) board AXP313A PMIC HDMI HDMI Audio H616 Audio Codec AC200 or AC300 (Drive automatic detection) ethernet PHY inside the H616 chip Onboard RTL8189FS WIFI Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] HDMI: The CLI and desktop displays are both normal [x] H616 Audio Codec: LINEOUTL/R aplay -D hw:0,0 /usr/share/sounds/alsa/Noise.wav output audio is normal [x] AC200 or AC300: recognize the PHY(ac200/ac300) and connect to the network normally [x] RTL8189FS WIFI: conne…

Description This introduces support for the BPI-CM4 module following the specifications of the RPI-CM4 module, using the BPI-CM4IO baseboard, but should support any CM4 compatible baseboards. https://wiki.banana-pi.org/Banana_Pi_BPI-CM4 The Linux DT changes has been submitted (https://lore.kernel.org/all/20230303-topic-amlogic-upstream-bpi-cm4-v2-0-2ecfde76fc4d@linaro.org/) and merged (https://git.kernel.org/amlogic/c/0262f2736978b1763363224698f47112a148dab0) upstream, the U-Boot changes are still in review (https://lore.kernel.org/all/20230307-u-boot-cm4-v1-0-43f5a393cd37@linaro.org/) How Has This Been Tested? Full testing must be done before switching this PR out of …

Description Current kernel deb package script ignores localversion of linux-next like -next-20231222, which will not pass deb building. This commit will add this localversion when grabbing kernel version. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh kernel BOARD=rock-5b BRANCH=edge DEB_COMPRESS=xz KERNEL_GIT=shallow, tested with KERNELSOURCE changed to https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git. [x] Built kernel runs normally. [x] Normal non-next kernel source tested Checklist: [x] My code follows the style guideline…

Description With this change, it is possible to select the collabora branch and build it on a Radxa Rock 5A. How Has This Been Tested? In Ubuntu on an x64 CPU, I have run ./compile.sh, selected the Rock-5a wip product, and then selected the collabora branch. I built if with desktop (which is overkill of course), but it boots nicely to Linux. I was allowed to setup my own user and the Ethernet port works nicely. uname -a Linux rock-5a 6.5.0-rc1-collabora-rockchip-rk3588 #1 SMP PREEMPT_DYNAMIC Fri Jul 28 15:49:06 UTC 2023 aarch64 GNU/Linux lsusb Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub B…

Description In order to achieve full compatibility between kernel, headers and libc, we need to build kernel per distribution, native, with distro compilers. In order to achieve that, we also need to store kernel into its repository. This method also significantly increases arm64 build load. To do: [ ] secure at least two serious arm64 irons [ ] merge sub components Jira reference number AR-1407 How Has This Been Tested? [x] Basic tests Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to t…

Description Add huawei matebook e go support How Has This Been Tested? Tested on HUAWEI MateBook E Go installed on sd card and device is booting fine Checklist: My code follows the style guidelines of this project I have performed a self-review of my own code I have commented my code, particularly in hard-to-understand areas I have made corresponding changes to the documentation My changes generate no new warnings Any dependent changes have been merged and published in downstream modules View the full article

Description basiclly, legacy kernel for board firefly-itx-3588j How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] build [x] boot [x] can play music, Hi-Fi! Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [ ] dependent on https://github.com/armbian/linux-rockchip/pull/193 View the full article

Description Firmware update. Jira reference number AR-1700 How Has This Been Tested? [ ] Build test as HW is n/a Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Add support for NanoPi R4SE, which has eMMC for R4S. The dts file mostly come from lede When upgrade to kernel 6.0, it will be much simple since the FriendlyElec already contrib it, armbian should only need this. How Has This Been Tested? I have compiled this patch in userpatches and running on R4SE hardware for a month (kernel upgrades disabled). Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [x] Any dependent changes h…

Description Add support for NanoPi R6S and R6C devices. Both devices are almostly same so we can have one image for them. Kernel PR: https://github.com/armbian/linux-rockchip/pull/15 Jira reference number AR-1663 How Has This Been Tested? [x] USB ports [x] eMMC boot [x] Ethernet ports [ ] Xorg works Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View …

Description Jira reference number AR-1361 How Has This Been Tested? [ ] Booting both kernels [ ] Check basic functions: BT, audio, 3D acceleration, ... Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description This PR adds support for Recore A5, A6, and A7 hardware. Recore is a 3D printer control board based on Allwinner A64. Since the board uses the AR100 for real time stepping, the SCP is disabled and instead a version of Klipper is loaded instead. How Has This Been Tested? The patches have been tested by building the current and legacy kernels with the minimal images. [ ] Minimal image with current kernel [ ] Minimal image with legacy kernel Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding c…

Description Add support for rk3399 based SBC Leez P710 How Has This Been Tested? Build noble desktop img with command: ./compile.sh build BOARD=leez-rk3399 BRANCH=edge BUILD_DESKTOP=yes BUILD_MINIMAL=no DESKTOP_APPGROUPS_SELECTED='browsers chat desktop_tools editors email internet multimedia office programming remote_desktop' DESKTOP_ENVIRONMENT=gnome DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base DOWNLOAD_MIRROR=bfsu EXPERT=yes EXTRAWIFI=no KERNEL_CONFIGURE=no PREFER_DOCKER=no RELEASE=noble Write the output img to tf card, inserd the card into the board, power up the board, the board can run into noble desktop. Checklist: [ ✓] My code follows the style guidelines of thi…

Description Add support for a rk3568 based SBC Lubancat2 in my hand. The u-boot and linux kernel support is landing mainline for a few months. How Has This Been Tested? Test: ./compile.sh build BOARD=lubancat2 BRANCH=edge BUILD_DESKTOP=yes BUILD_MINIMAL=no DESKTOP_APPGROUPS_SELECTED='browsers chat desktop_tools editors email internet multimedia office programming remote_desktop' DESKTOP_ENVIRONMENT=xfce DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base DOWNLOAD_MIRROR=bfsu ENABLE_EXTENSIONS=mesa-vpu EXPERT=yes EXTRAWIFI=no KERNEL_CONFIGURE=no PREFER_DOCKER=no RELEASE=noble VENDOR=Armbian Write the image to tf card, insert the card to the board, the board can boot into desktop…

Description Add support for RK3588 based board Cool PI CM5 EVB Jira reference number [AR-9999] How Has This Been Tested? ./compile.sh build BOARD=coolpi-cm5 BRANCH=edge BUILD_DESKTOP=yes BUILD_MINIMAL=no DESKTOP_APPGROUPS_SELECTED='3dsupport browsers chat desktop_tools editors email internet multimedia office programming remote_desktop' DESKTOP_ENVIRONMENT=gnome DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base DOWNLOAD_MIRROR=bfsu EXPERT=yes EXTRAWIFI=no KERNEL_CONFIGURE=no PREFER_DOCKER=no RELEASE=noble Download the compiled img to sdcard, and can boot. Checklist: Please delete options that are not relevant. [✓ ] My code follows the style guidelines of this project [✓] I…

Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Boot test with basic functions checked [x] Install and boot from eMMC Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding chang…

add support for various HID game controllers and waydroid on rk3588 legacy kernel Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ ] Test A [ ] Test B Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I…

Description Cleanup of @monkaBlyat https://github.com/armbian/build/pull/4732 CONFIG_PSI=y is enabled by default now. Should not cause troubles. Jira reference number AR-1531 How Has This Been Tested? [x] Build test Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

No descriptionView the full article

Description This might help diverting users from abusing issue tracker for seeking support. How Has This Been Tested? UX / guide change. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description As per title + leave defaults as is. Jira reference number AR-2027 How Has This Been Tested? [x] Making one image Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description For populating repository we need to obtain all artefacts that are in OCI_TARGET_BASE How Has This Been Tested? [x] Test run in development branch Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Add collective target "default" The BUILD_ONLY variable should not be empty, that is, the target for the assembly should be defined. If this is not the case, open a selection dialog with marked goals that correspond to the default collective goal. This work provides an opportunity for the implementation of the choice dialog. Checklist: [ ] Test build View the full article

Follow up to #4955 — add sample of term type inclusion, whitelist my terminal View the full article

Description Add support for "i.MX8M Plus" boards from TQ-System. Use atf and uboot from https://github.com/tq-systems Add BSP packages for the tqma8mpxl family Add kernel patches (6.1 and 6.6) for the tqma8mpxl family Supported mainline kernels: current = 6.1.71 and edge=6.6.10 Supported boards: mba8mp-ras314 mba8mpxl How Has This Been Tested? [x] Build images for mba8mp-ras314 and mba8mpxl with current and edge kernel [x] Boot test "bookworm_current" and "bookworm_edge" mba8mp-ras314 [x] Boot test "jammy_current" and "bookworm_edge" mba8mpxl [x] HDMI, WLAN, USB test's mba8mp-ras314" bookworm_edge" with xfce image [x] HDMI, WLAN, USB test's mba8mpxl" bookworm_edge"…

Add TV Box targets to stable builds per discussion at the 23/01/18 Developers Meeting. Added aml-s9xx-box and rk3318-box (rk322x-box was already there) Changes to be committed: modified: config/targets.conf View the full article

Description Ordered this WiFi key and it was not working out of the box. Adding pids (and also for Netgear variant) helps that it works OOB. Jira reference number AR-1803 How Has This Been Tested? [x] Build and booted USB wireless device (on Odroid N2 https://paste.armbian.com/onulekucil) Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

This config simplifies the U-Boot build only scenario. If this switch is set, then KERNEL_ONLY is implied to "yes". The U-Boot only build also ensures proper host prepare and any other validation, the default build procedure performs. The motivation is to simplify UBOOT_ONLY building by just one compile parameter / switch, but keeping the default dependent compile procedures like e.g. host compare and other pre-config validations as is. This makes it also useful for CICD compile configurations. Changes lib/functions/main/config-prepare.sh: imply to set KERNEL_ONLY=yes, if UBOOT_ONLY is set "yes" lib/functions/main/default-build.sh: changed do_default(): added appr…

Description As the title says. Good for testing & make test images. Jira reference number AR-1380 How Has This Been Tested? [x] Generated XFCE, Gnome and Cinnamon desktop Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Necessary changes only to make repository work. There is probably lots of work to do laser... Jira reference number [AR-9999] How Has This Been Tested? Builds until the point where it tries to grab release file form apt repo which obviously fails. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Please include a summary of the change and which issue is fixed. Please also include relevant motivation and context. List any dependencies that are required for this change. Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ ] Test A [ ] Test B Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no ne…

add ugoos x3 support to aml-s9xx-box: added prebuild uboot 2024.04 ("u-boot-s905x3" does not work with ugoos) added patch to build u-boot from sources added dts for ugoos x3 View the full article

Description Add patches as Justin Green mentioned to enable DMA buffer caching on hantro and rkvdec driver. Hantro and rkvdec driver have set dst_vq->dma_attrs to DMA_ATTR_ALLOC_SINGLE_PAGES | DMA_ATTR_NO_KERNEL_MAPPING and it will not pass check in dma_alloc_noncontiguous, so I add a patch to deal with it. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] rockchip64-edge build success [x] chromium v4l2 decoder works on orangepi3b. Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I ha…

Add WiP Mekotronics R58 boards (rockchip-rk3588) mekotronics.com rockchip-rk3588: add new board mekotronics-r58-minipc.wip (Mekotronics R58 MiniPC, and variants) rockchip-rk3588: add new board mekotronics-r58x.wip (Mekotronics R58X) rockchip-rk3588: add new board mekotronics-r58x-4g.wip (Mekotronics R58X-4G); add u-boot patches rockchip-rk3588: set ROCKUSB_BLOB for RockUSB Maskrom -> Loader mode u-boot: same as Radxa Rock-5A. RockUSB and UMS works; boot from eMMC only. No USB, no NVMe. Can stop u-boot by holding Shift-M during boot on serial console. Kernel: was handled at https://github.com/armbian/linux-rockchip/pull/12 and https://github.com/armbian/linux-rockch…

See https://github.com/armbian/build/pull/4814#issuecomment-1416919466 View the full article

Description Due to possible transitioning from WPA_Supplicant to Intel's IWD daemon for Linux wireless needs hard dependancy was removed. Based on https://github.com/armbian/build/pull/4817 (better to fix this in master and then cherry pick to next) Jira reference number AR-1534 How Has This Been Tested? No needed. Without, tool is not installed anymore but we need it. View the full article

Description Looks like a solution for this. Jira reference number AR-1650 How Has This Been Tested? [ ] Build an image, setup and RDP to it Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstream modules View the full article

Description Basic support has been added, WIFI and Bluetooth are now working, the sound card can be recognized, and GPU cannot be used because the panel driver cannot be used. Currently, only simple fb can be used, and touch cannot work due to geni report some dma error, which requires some work Touch driver from https://github.com/qaz6750/linux/commit/bdfe4cfd872e8c8ff484e263dcf534e2f1844775 Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Boot and enter the Shell [x] Screen can display the desktop [x] WiFi&BT [x] USB RD…

Description I was accidentally burned when updating my BSP package this week. I had inadvertently left some important xorg config in 01-armbian-defaults.conf, and this file was overwritten during the upgrade. I came to the conclusion that either: the comment in 01-armbian-defaults.conf should be updated to indicate to users that the file may be overwritten and should not be edited, or 01-armbian-defaults.conf should be placed in the conffiles list so that an end-user can review any potential changes to the file as part of the package upgrade process. I contend that option (2) is better, because even if a user hasn't edited this file, they should still get some notice …

Description Zoom install for x86 desktop. Jira reference number AR-1357 How Has This Been Tested? [ ] Build x86 desktop image Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Description Add cpu-frequency to orangepizero2, allwinner h616. From sunxi 5.16 the drivers and dtsi, dts files have the necessary support. Add: sun50i-h616-cpu-opp.dtsi Additions: sun50i-h616-orangepi-zero2.dts +#include"sun50i-h616-cpu-opp.dtsi" +&cpu0 { + cpu-supply = <&reg_dcdca>; +}; Jira reference number [AR-9999] How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Test A Build: compiled and booted [x] Test B Board: test success @orangepizero2:~$ uname -a Linux orangepizero2 5.19.6-sunxi64 #trunk SMP Mon Sep 5 23:16:49 UTC 2022 aarch64 …

Description Added "collabora" to the interactive config kernel branch selection (new branch for rk3588) How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Interactive configuration started Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the …

Description Added support for midstream kernels to the interactive config kernel branch selection. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [ x] Interactive configure rock 5B Checklist: [ ] My code follows the style guidelines of this project [ ] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [ ] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full ar…

Description Adds minimalist cloud-init support functionally equivalent to the Ubuntu implementation for the Raspberry PI. addresses issue #6197 Jira reference number AR-2035 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. View the full article

Description Added new Debian 12 Bookworm Jira reference number AR-1521 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] Build CLI and Minimal images [x] Build desktop XFCE image [x] Armbian repository needs to be updated due to missing packages... Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [ ] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes h…

Description This PR enables support for MediaTek USB modules in Rockship legacy kernel. MediaTek branch was enabled in the past but all the devices were set not to build. This change adds them as modules. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [X] Create and build full Armbian desktop image based on OPI5 WIP [X] Test with hardware on Orange PI 5 [X] Connect to Wifi network with image + Asus USB AC55 (MediaTek MT7621U) Checklist: [X] My code follows the style guidelines of this project [X] I have performed a self-review of my own code [X] I have comment…

Description added support for board core3566 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] vendor kernel 6.1 with ubuntu 24.04, server build. OK, with eth works. [x] edge kernel 6.10 with ubuntu 24.04, server build. Failed to boot. Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [x] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [x] Any dependent changes have been merged and publish…

kde-plasma for debian sid and debian bullseye View the full article

Description An attempt to improve review process. Code owners are automatically requested for review when someone opens a pull request that modifies code that they own. Code owners are not automatically requested to review draft pull requests. Jira reference number AR-1435 How Has This Been Tested? [ ] Not tested yet Checklist: [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [x] I have made corresponding changes to the documentation [x] My changes generate no new warnings [x] Any dependent changes have been merged and published in downstr…