gene1934

now I must confess this is not on armbian, but on debian image, and at 6.1.4, in the above link. the mkfs.gfs2 is command not found. and apt can't find it either, so I seem to be missing a pkg. What main pkg would I install to get it?

I might have bypassed the bug, I partitioned and formatted the 1T toshiba and it has now rebooted fully 2 times. And I have configured a vgroup labeled "amtapes". So what next, it (amtapes) is not visible in /dev yet so can't be mounted for use.

I think I've found a bug. I've now installed a 2nd Hub to spread the load to 3 drives a hub.A full powerdown reboot now finds the drives, at stable but odd addrresses but a reboot as root misses both hubs and finds nothing. 100% Repeatable. 3 drives plugged into each hub. So the load currants s/b under the hubs protective tripoff point. PSU is good for 20 amps. Hubs are identical, Chinese Achoro 7 port, all ports rated for usb-3.2 traffic. Works from powerup, fails for reboot. I think i'm in deeper than my IQ expected Why? Cheers, Gene1934, a CET back in $DAYJOB time.

I'm not out of the woods yet. I installed a bigger cache drive and its startup current kills the hub all this is plugged into, so ATM I'm in the process of mounting a 2nd fast hub to split the current up into something these funkity hubs can handle w/o shutdowns. With glue curing times, about another 36 hours to know if that is the fix.

1TB toshiba drive arrived & installed. Too much startup current for hub, hub shuts down instantly and in 3 powerdown reboots, no drives detected. unplugged last 2 drives leaving 4 plugged in, all 4 left plugged in, sda, sdb, sdc, sdd found ok. so an almost $40 Hub is piece of excrement. Do you know of a 7 port usb3.2 hub that can handle 6 drives? Ought to survive 5 amps per port used current. Or maybe good enough since I still have 2 open usb ports on the bpi-m5, and another hub just like this piece of shit, but I'll have to print another mount for the second hub. That will take a couple days as I'll have to give shoe-goo a chance to cure in addition to reworking another psu cord for the hub. And find another 1 foot std usb cable. Might spread it's drive tree out to 3 loads per hub to equalize and reduce the individual hub load. So I'm off to print the mount for a 2nd hub. Probably back later. These are all like tires I haven't kicked, yet. ;o)> At what stage in the setup do I apply a label to the drive so it survives the LVM configuration/creation? It would be a much shorter list to build if disk labels could be used. Thank you. Gene Heskett, old (90) retired CET.

Thank you, I'll try that in the morning.

Trouble setting up lvm2. vgcreate wrong because drive order is not now the plugin order on hub according to dmeg. interchanged cables vs ports for out of order discovery and rebooted but problem unchanged ack dmesg. So how do I blow away the volume_group that does not get made due to this error, so I can re vgcreate a new lvm? An hour later, I have tried, rearranging cable vs ports on the hub but the rusty drive stays at /dev/sdd# when it was /dev/sdf# b4 everything was partitioned. What the heck is going on? For this to stand a snow balls chance in hell of working, I MUST have stable drive id's. Can vgcreate use PARTUUID's instead of /dev/sda /dev/sdb etc as identifiers? Thank you, Gene1934 Thank you.

fussing about duplicate post, yes, same problem, different but identical machine. I have several of these bpi-m5's in service here, And its happened several times while I have reached the age of 90 where short term memory is only weeks. This then. with your link to systemd stuff, is bad code you inherited, blindly. My solution to that was/is to make hostname immutable after editing it. Much simpler than reading thru half a gigabyte of purposely opaque docs looking for clues. With the advent of led backlighting for monitor screens, CRT screens no longer get burnt in. So one thing badly needed is a bright red, much bigger mouse pointer that moves at about 1/10 th of its present speed, and an easy way to totally disable screen and mouse blanking. On a 3d printer, they are both a hindrance, adding 10 to 30 seconds to taking action when a printer malfunctions. And because I use this OS heavily, I also donate a smallish bit of my SS income to your cause on a monthly basis. Thank you Igor.

up all night, finally got it working. list of stuff I did: download latest 2505 bookworm-xfce and reburn the u-us card 3 times. copied 40 entry /etc/hosts file from working machine. edit /etc/hostname to change it to unique name amanda, then make it immutable as that did not survive a reboot. rm 10-* in etc/netplan, rename armbian.yaml to 10-armbian.yam editing it as needed, and edit /etc/nsswitch.conf to make network setup start as "hostname files dns" rebooting after each stage. So hostname now stays at amanda, and nsswitch.conf works as ordered. I can ping yahoo.com in addition to my other local machines and have now updated 208 pkgs. rebooted looks ok. Now I can get back to making a 20T lvm out of 5 4T SSD's, But first some breakfast and a shot of insulin, and a nap while the local weather settles, its poured piss out of a cowbarn boot most of the night. Thank you for the links, they were educational.

netplan is a joke. It looks like it might work IF ipv6 was totally disabled. everything I've entered has been applied to /dev/br0. but shown while entering it as end0 This is totally broken. Can I still put this crap in /etc/networking/interfaces.d? Help please.

Network setup in the latest bookworm+xfce's armbian config won't allow a network setup I've been using for 25 years. Its an all ipv4 static setup using hosts files. It apparetly asumes only valid ipv6 addresses but the nearest ipv6 enabled ISP is over 100 miles away from me in north central West Virginia USA.The idea is it will query the router for any name not found in the /etc/hosts file. Thhe switch trigger being a hardcopy /etc/resolv.conf. This is normally and instantly accomplished as dd-wrt caches previously looked up addresses. And if not found in dd-wrt's cache it relays the request to my ISP's dns server. BUT BUT BUT armbian-config refuses to accept valid ipv4 addresses by hashing them to apparently random errors, digits duplicated or left out When looking at the results no dhcp4 or 6 of is enabled as expected. So how do I fix this first boot problem? This is all on a banannapi-m5 I intend to make an amanda-3.5.4 based nas out of. Thanks for any help. The solved x tag is a lie as it won't post w/o it.

thanks, pulled it.

These are usb3 labeled adapters, I did have problems earlier on a pi3b using another brand of adapter, but these startech adapters have been bulletproof, for years. c0rnelius current kernel is .6.12.22-current-meson64, will this patch apply? I've also found data on these drives indicating a 20W peak power for write operations. My present drive psu is a pretty hot usb wall wort, so based on 5x20, I have a 100W rated supply from amazon should be here midweek, and which will also power a 5" fan in one end of the drive cage. Which should move enough air to cool the drives. The question is now about the 7 port usb3 hub, can it deliver the 4 amps per port these drives need during a wright operatoin. Probably can't be answered until I can get a scope on the line. And that won't be done till the far end of the week. ;o}... If & when i get the psu i'll likely be back with more pix. Thanks until then. . . Cheers Gene.

just did another upgrade, 128 pkgs. no errors now but only 3 of the 5 drives show, but drives possibly too warm.drives are warm, need additional cooling. have 5" fan in front of enclosier but which pins do I connect it to? Or should I connect that big a fan direct to psu?

The drives are gigastones, made in Taiwan. Sata to usb3 Adaptor cables are latest StarTech's. I have had zero failures with that brand in over a decade of use here.

I am one of your monthly contributors. I too seem to be subjected recently, noted after doing an apt upgrade. -y. I have a 5 volt 5 amp supply for the bpi-m5 psu plugged into the C port. booting is now both intermittent and several mintes to get started. I have a usb3 hub with 7 usb3 ports plugged into one of the usb3 ports on the bpi-m5. The last of many attempts to boot it worked after the long delay so I plugged the hubs src cable back in to see if something has failed in the 5, 4T drives currently plugged in for amanda's use. But that now gets me an error msg, something about config #1 is returning an error 110, which it did NOT do a couple months ago. And dmesg is only reporting 4 drives. All intended to be one logical volume. Any idea how to determine which of hose 5 drives has gone toes up? Thank you. Gene Heskett, CET.

I assume this was the expected result: Preparing to unpack .../snapd_2.66.1+22.04_arm64.deb ... Unpacking snapd (2.66.1+22.04) over (2.65.3+22.04) ... Preparing to unpack .../thunderbird_9%3a128.5.0+build1-0ubuntu0.22.04.1~mt1armbian1_arm64.deb ... Unpacking thunderbird (9:128.5.0+build1-0ubuntu0.22.04.1~mt1armbian1) over (9:128.4.4+build1-0ubuntu0.22.04.1~mt1armbian1) ... Setting up snapd (2.66.1+22.04) ... snapd.failure.service is a disabled or a static unit not running, not starting it. snapd.snap-repair.service is a disabled or a static unit not running, not starting it. Setting up thunderbird (9:128.5.0+build1-0ubuntu0.22.04.1~mt1armbian1) ... plz advise it not. Thanks Igor.

its my understanding that both fire-fox and t-bird are only snaps these days. Being a little paranoid, I didn't delete that file but renamed it to .last which apt barked about but didn't use. then the usual reload & full-upgrade procedure replaced both snapd and t-bird. t-bird I could probably remove as that is a printer and has never sent/received an email. My network does not disallow that as all other net stuff still works. Firefox apparently has its own update mechanim, all I need to do is stop it for an hour or so, and get the new version when it announces its availability in the upper right corner of its workspace. Thank you Igor.

I'll give that a shot after the weekend when the current new dirt addition to this printer should be working. Right now I'm torture testing the relay that will control the motor driver, waiting on Amazon to deliver some 30 amp 50 volt schotkey's to make a flywheel diode. Otherwise the back emf fry's the bugs in a 300 watt buck kit at turnoff time, that limits the start up currant to something the OEM 24 volt supply can handle. I am a 90 yo, long retired CET, we teach EE's stuff their profs didn't but getting rusty now. Thanks Igor.

Err:1 https://cli.github.com/packages stable InRelease The following signatures were invalid: EXPKEYSIG 23F3D4EA75716059 GitHub CLI <opensource+cli@github.com>

gene@bpi51e5p:~/kiauh-master$ sudo apt list --upgradable Listing... Done snapd/jammy-updates 2.66.1+22.04 arm64 [upgradable from: 2.65.3+22.04] thunderbird/jammy 9:128.5.0+build1-0ubuntu0.22.04.1~mt1armbian1 arm64 [upgradable from: 9:128.4.4+build1-0ubuntu0.22.04.1~mt1armbian1]

looks like the github key has changed how do I refresh it?

uptodated today, jammy on bpi-m5 running 3d printer with klipper etc. With snapd frozen, so is firefox. possible fix? passwd f-u, I am that other contributing member but finally got it reset.

neither apt nor snap will update firefox, apt says possible mirror update in progress. snap refresh or snap list says its current. Call me puzzled. Which do I uninstall??? .

I looked at the man page, last time I played with it was 2 decades ago. Its grown 2500 lines since and at my present age approaching 90, is gibberish. So I saved the netplan stuff and rewrote the card to start fresh. thanks Werner