Hey All -

 

So I decided to upgrade my Udoo from 4.5 (Debian Jessia, kernel 3.14.28) to the latest 5.25 Xenial.

 

I gave next (4.4.46) a try, and it seemed to work awesome, however it seems like no one wants 1wire (still - it only takes up 1 gpio!).

 

I built custom kernels enabling 1wire in the kernel and updated (or for default adding) 1wire to be enabiled in the imx6qdl-udoo.dtsi, however after I install the kernels, it just sits indefinitely at the red Armbian logo on boot.

 

On 4.4.46, i was able to just install all the debs via dpkg -i *.deb

On 3.14.56, I had to use dpkg --force-all -i *.deb

 

Any ideas on what I'm doing wrong?  Its been a while, so I'm sure a bunch has changed, but adding 1wire in the kernel shouldn't cause a freeze

I built custom kernels enabling 1wire in the kernel and updated (or for default adding) 1wire to be enabiled in the imx6qdl-udoo.dtsi, however after I install the kernels, it just sits indefinitely at the red Armbian logo on boot.

 

Strange, upgrade / kernel install should work this way. Can you catch boot log via serial console, that we can see more?

So one thing I noticed is that armbian's udoo kernel configs (both default & next) are pretty different than from both default & next in respective git repos (patrykk's has all the 1wire stuff as modules, with 1wire as disabled, but you can just rebuild the dtb file) - shouldn't be an issue since I assume you build with the configs in your repo vs theirs..  Below are the my kernel diffs vs armbian, install, and boot log.  I just edited imx6qdl-udoo.dtsi and changed "disabled" to "okay" during kernel config & made the mods - don't think that should cause the boot to break

 

Kernel diffs:

$ diff armbian_default/linux-udoo-next.config linux-udoo-next.config

3c3

< # Linux/arm 4.4.6 Kernel Configuration

---

> # Linux/arm 4.4.0 Kernel Configuration

2055c2055,2082

< # CONFIG_W1 is not set

---

> CONFIG_W1=y

> CONFIG_W1_CON=y

>

> #

> # 1-wire Bus Masters

> #

> # CONFIG_W1_MASTER_DS2490 is not set

> # CONFIG_W1_MASTER_DS2482 is not set

> CONFIG_W1_MASTER_MXC=y

> # CONFIG_W1_MASTER_DS1WM is not set

> CONFIG_W1_MASTER_GPIO=y

>

> #

> # 1-wire Slaves

> #

> CONFIG_W1_SLAVE_THERM=y

> # CONFIG_W1_SLAVE_SMEM is not set

> # CONFIG_W1_SLAVE_DS2408 is not set

> # CONFIG_W1_SLAVE_DS2413 is not set

> # CONFIG_W1_SLAVE_DS2406 is not set

> # CONFIG_W1_SLAVE_DS2423 is not set

> # CONFIG_W1_SLAVE_DS2431 is not set

> # CONFIG_W1_SLAVE_DS2433 is not set

> # CONFIG_W1_SLAVE_DS2760 is not set

> # CONFIG_W1_SLAVE_DS2780 is not set

> # CONFIG_W1_SLAVE_DS2781 is not set

> # CONFIG_W1_SLAVE_DS28E04 is not set

> # CONFIG_W1_SLAVE_BQ27000 is not set

4175a4203

> # CONFIG_DEBUG_UART_BCM63XX is not set

 

Update:

root@udoo:~/kupdate# ls -la

total 17072

drwxr-xr-x 2 root root    4096 Feb 11 23:28 .

drwx------ 7 root root    4096 Feb 11 23:28 ..

-rwxr--r-- 1 root root   50196 Feb 11 06:11 linux-firmware-image-4.4.0-udoo_5.25_armhf.deb

-rwxr--r-- 1 root root 7188908 Feb 11 06:11 linux-headers-4.4.0-udoo_5.25_armhf.deb

-rwxr--r-- 1 root root 9289516 Feb 11 06:12 linux-image-4.4.0-udoo_5.25_armhf.deb

-rwxr--r-- 1 root root  799462 Feb 11 06:11 linux-libc-dev_5.25_armhf.deb

-rwxr--r-- 1 root root  135072 Feb 11 06:03 linux-u-boot-next-udoo_5.25_armhf.deb

root@udoo:~/kupdate# dpkg -i *.deb

Selecting previously unselected package linux-firmware-image-4.4.0-udoo.

(Reading database ... 140089 files and directories currently installed.)

Preparing to unpack linux-firmware-image-4.4.0-udoo_5.25_armhf.deb ...

Unpacking linux-firmware-image-4.4.0-udoo (5.25) ...

Selecting previously unselected package linux-headers-4.4.0-udoo.

Preparing to unpack linux-headers-4.4.0-udoo_5.25_armhf.deb ...

Unpacking linux-headers-4.4.0-udoo (5.25) ...

Selecting previously unselected package linux-image-4.4.0-udoo.

Preparing to unpack linux-image-4.4.0-udoo_5.25_armhf.deb ...

Unpacking linux-image-4.4.0-udoo (5.25) ...

Preparing to unpack linux-libc-dev_5.25_armhf.deb ...

Unpacking linux-libc-dev (5.25) over (4.4.0-59.80) ...

Preparing to unpack linux-u-boot-next-udoo_5.25_armhf.deb ...

Unpacking linux-u-boot-udoo-next (5.25) over (5.25) ...

Setting up linux-firmware-image-4.4.0-udoo (5.25) ...

Setting up linux-headers-4.4.0-udoo (5.25) ...

Setting up linux-image-4.4.0-udoo (5.25) ...

update-initramfs: Generating /boot/initrd.img-4.4.0-udoo

update-initramfs: Converting to u-boot format

Setting up linux-libc-dev (5.25) ...

Setting up linux-u-boot-udoo-next (5.25) ...

Updating u-boot on device /dev/mmcblk0

root@udoo:~/kupdate# 

 

Boot Log (after update):

U-Boot SPL 2015.10-armbian (Feb 10 2017 - 23:03:32)

 

 

U-Boot 2015.10-armbian (Feb 10 2017 - 23:03:32 -0700)

 

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz

Reset cause: POR

Board: UDOO Quad

DRAM:  1 GiB

MMC:   FSL_SDHC: 0

*** Warning - bad CRC, using default environment

 

auto-detected panel HDMI

Display: HDMI (1280x720)

In:    serial

Out:   serial

Err:   serial

Net:   using phy at 6

FEC [PRIME]

Hit any key to stop autoboot:  0

switch to partitions #0, OK

mmc0 is current device

** Unrecognized filesystem type **

Device Tree: dts/imx6q-udoo-hdmi.dtb

** Unrecognized filesystem type **

Booting from net ...

FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !

BOOTP broadcast 1

BOOTP broadcast 2

BOOTP broadcast 3

BOOTP broadcast 4

BOOTP broadcast 5

BOOTP broadcast 6

BOOTP broadcast 7

BOOTP broadcast 8

BOOTP broadcast 9

BOOTP broadcast 10

BOOTP broadcast 11

BOOTP broadcast 12

BOOTP broadcast 13

BOOTP broadcast 14

BOOTP broadcast 15

BOOTP broadcast 16

BOOTP broadcast 17

 

Retry time exceeded; starting again

FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !

BOOTP broadcast 1

BOOTP broadcast 2

BOOTP broadcast 3

BOOTP broadcast 4

BOOTP broadcast 5

BOOTP broadcast 6

BOOTP broadcast 7

BOOTP broadcast 8

BOOTP broadcast 9

BOOTP broadcast 10

BOOTP broadcast 11

BOOTP broadcast 12

BOOTP broadcast 13

BOOTP broadcast 14

BOOTP broadcast 15

BOOTP broadcast 16

BOOTP broadcast 17

 

Retry time exceeded; starting again

Bad Linux ARM zImage magic!

=>

 

Here's the first boot I captured.. I'm going to try again, without updating uboot, just linux-image-4.4.0-udoo_5.25_armhf.deb and linux-firmware-image-4.4.0-udoo_5.25_armhf.deb

 

U-Boot SPL 2015.10-armbian (Feb 02 2017 - 03:15:42)

 

 

U-Boot 2015.10-armbian (Feb 02 2017 - 03:15:42 +0100)

 

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz

Reset cause: POR

Board: UDOO Quad

DRAM:  1 GiB

MMC:   FSL_SDHC: 0

*** Warning - bad CRC, using default environment

 

auto-detected panel HDMI

Display: HDMI (1280x720)

In:    serial

Out:   serial

Err:   serial

Net:   using phy at 6

FEC [PRIME]

Hit any key to stop autoboot:  0

switch to partitions #0, OK

mmc0 is current device

Scanning mmc

Found U-Boot script /boot.scr

** File not found /boot.scr **

** Unrecognized filesystem type **

Found U-Boot script /boot/boot.scr

1757 bytes read in 109 ms (15.6 KiB/s)

Running bootscript from mmc ...

## Executing script at 12000000

Booting from SD

** File not found /boot/armbianEnv.txt **

** Unrecognized filesystem type **

4764730 bytes read in 379 ms (12 MiB/s)

6144136 bytes read in 497 ms (11.8 MiB/s)

0 bytes read in 98 ms (0 Bytes/s)

37690 bytes read in 564 ms (64.5 KiB/s)

Kernel image @ 0x12000000 [ 0x000000 - 0x5dc088 ]

## Loading init Ramdisk from Legacy Image at 14800000 ...

   Image Name:   uInitrd

   Image Type:   ARM Linux RAMDisk Image (gzip compressed)

   Data Size:    4764666 Bytes = 4.5 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Flattened Device Tree blob at 18000000

   Booting using the fdt blob at 0x18000000

   Using Device Tree in place at 18000000, end 1800c339

 

Starting kernel ...

 

Loading, please wait...

starting version 229

Begin: Loading essential drivers ... done.

Begin: Running /scripts/init-premount ... done.

Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.

Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems

done.

Begin: Will now check root file system ... fsck from util-linux 2.27.1

[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1

/dev/mmcblk0p1: clean, 147301/178816 files, 526555/713984 blocks

done.

done.

Begin: Running /scripts/local-bottom ... done.

Begin: Running /scripts/init-bottom ... done.

 

Welcome to Ubuntu 16.04.1 LTS!

 

[  OK  ] Listening on udev Control Socket.

[  OK  ] Set up automount Arbitrary Executab...ats File System Automount Point.

[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.

[  OK  ] Reached target Remote File Systems (Pre).

[  OK  ] Created slice System Slice.

[  OK  ] Created slice system-serial\x2dgetty.slice.

[  OK  ] Reached target Swap.

[  OK  ] Listening on Journal Socket.

         Starting Restore / save the current clock...

[  OK  ] Listening on Syslog Socket.

[  OK  ] Started Forward Password Requests to Wall Directory Watch.

[  OK  ] Created slice User and Session Slice.

         Starting Create list of required st... nodes for the current kernel...

[  OK  ] Reached target Encrypted Volumes.

[  OK  ] Started Dispatch Password Requests to Console Directory Watch.

[  OK  ] Listening on fsck to fsckd communication Socket.

[  OK  ] Listening on udev Kernel Socket.

         Mounting POSIX Message Queue File System...

[  OK  ] Reached target Remote File Systems.

[  OK  ] Reached target User and Group Name Lookups.

         Starting Nameserver information manager...

         Starting Load Kernel Modules...

         Starting Set console keymap...

[  OK  ] Reached target Slices.

         Starting Remount Root and Kernel File Systems...

[  OK  ] Listening on Journal Socket (/dev/log).

[  OK  ] Mounted POSIX Message Queue File System.

[  OK  ] Started Restore / save the current clock.

[  OK  ] Started Create list of required sta...ce nodes for the current kernel.

[  OK  ] Started Load Kernel Modules.

[  OK  ] Started Set console keymap.

[  OK  ] Started Remount Root and Kernel File Systems.

[  OK  ] Started Nameserver information manager.

         Starting udev Coldplug all Devices...

         Starting Load/Save Random Seed...

         Starting Apply Kernel Variables...

         Mounting FUSE Control File System...

         Starting Create Static Device Nodes in /dev...

[  OK  ] Mounted FUSE Control File System.

[  OK  ] Started Load/Save Random Seed.

[  OK  ] Started Apply Kernel Variables.

[  OK  ] Started Create Static Device Nodes in /dev.

         Starting udev Kernel Device Manager...

[  OK  ] Reached target Local File Systems (Pre).

         Mounting /tmp...

[  OK  ] Mounted /tmp.

[  OK  ] Started udev Coldplug all Devices.

[  OK  ] Started udev Kernel Device Manager.

[  OK  ] Started Entropy daemon using the HAVEGE algorithm.

         Starting Journal Service...

[  OK  ] Reached target Local File Systems.

         Starting Raise network interfaces...

         Starting Set console font and keymap...

         Starting Armbian enhanced Log2Ram...

[  OK  ] Found device /dev/ttymxc1.

[  OK  ] Reached target Sound Card.

[  OK  ] Started Journal Service.

[  OK  ] Started Armbian enhanced Log2Ram.

[  OK  ] Started Raise network interfaces.

[  OK  ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.

[  OK  ] Started ifup for eth0.

         Starting Flush Journal to Persistent Storage...

[  OK  ] Started Flush Journal to Persistent Storage.

         Starting Create Volatile Files and Directories...

         Starting Load/Save RF Kill Switch Status...

[  OK  ] Started Create Volatile Files and Directories.

[  OK  ] Started Load/Save RF Kill Switch Status.

         Starting Update UTMP about System Boot/Shutdown...

[  OK  ] Reached target System Time Synchronized.

[  OK  ] Started Update UTMP about System Boot/Shutdown.

[  OK  ] Reached target System Initialization.

[  OK  ] Started Daily Cleanup of Temporary Directories.

[  OK  ] Reached target Paths.

[  OK  ] Listening on D-Bus System Message Bus Socket.

[  OK  ] Started Daily apt activities.

[  OK  ] Reached target Timers.

         Starting Armbian filesystem resize service...

[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.

[  OK  ] Reached target Sockets.

[FAILED] Failed to start Set console font and keymap.

See 'systemctl status console-setup.service' for details.

[  OK  ] Started Armbian filesystem resize service.

[  OK  ] Reached target Basic System.

         Starting LSB: Start/stop sysstat's sadc...

         Starting Accounts Service...

[  OK  ] Started Armbian first run tasks.

[  OK  ] Created slice system-getty.slice.

         Starting Avahi mDNS/DNS-SD Stack...

         Starting LSB: No Display Manager...

         Starting Login Service...

         Starting System Logging Service...

         Starting LSB: Starts LIRC daemon....

[  OK  ] Started Regular background program processing daemon.

         Starting LSB: Load kernel modules needed to enable cpufreq scaling...

         Starting LSB: Armbian gathering hardware information...

[  OK  ] Started D-Bus System Message Bus.

[  OK  ] Started Avahi mDNS/DNS-SD Stack.

         Starting Network Manager...

         Starting Permit User Sessions...

         Starting Save/Restore Sound Card State...

[  OK  ] Started System Logging Service.

[  OK  ] Started Permit User Sessions.

[  OK  ] Started Save/Restore Sound Card State.

[  OK  ] Started LSB: Start/stop sysstat's sadc.

[  OK  ] Started LSB: Armbian gathering hardware information.

[  OK  ] Started LSB: No Display Manager.

[  OK  ] Started LSB: Starts LIRC daemon..

[  OK  ] Started LSB: Load kernel modules needed to enable cpufreq scaling.

[  OK  ] Started Network Manager.

[  OK  ] Started Login Service.

         Starting Network Manager Script Dispatcher Service...

[  OK  ] Reached target Network.

         Starting OpenBSD Secure Shell server...

         Starting Network Manager Wait Online...

         Starting Authenticate and Authorize Users to Run Privileged Tasks...

         Starting LSB: set CPUFreq kernel parameters...

         Starting Set console scheme...

[  OK  ] Started Network Manager Script Dispatcher Service.

[  OK  ] Started Set console scheme.

[  OK  ] Started LSB: set CPUFreq kernel parameters.

         Starting LSB: Set sysfs variables from /etc/sysfs.conf...

         Starting Hostname Service...

[  OK  ] Started LSB: Set sysfs variables from /etc/sysfs.conf.

[  OK  ] Started Authenticate and Authorize Users to Run Privileged Tasks.

[  OK  ] Started Accounts Service.

[  OK  ] Started Hostname Service.

[  OK  ] Started OpenBSD Secure Shell server.

         Starting WPA supplicant...

[  OK  ] Started WPA supplicant.

[  OK  ] Started Network Manager Wait Online.

[  OK  ] Reached target Network is Online.

         Starting LSB: disk temperature monitoring daemon...

         Starting LSB: Start NTP daemon...

         Starting LSB: Advanced IEEE 802.11 management daemon...

         Starting /etc/rc.local Compatibility...

[  OK  ] Started LSB: Advanced IEEE 802.11 management daemon.

[  OK  ] Started /etc/rc.local Compatibility.

[  OK  ] Started LSB: disk temperature monitoring daemon.

[  OK  ] Started Serial Getty on ttymxc1.

[  OK  ] Started Getty on tty1.

[  OK  ] Reached target Login Prompts.

[  OK  ] Started LSB: Start NTP daemon.

[  OK  ] Reached target Multi-User System.

[  OK  ] Reached target Graphical Interface.

         Starting Update UTMP about System Runlevel Changes...

[  OK  ] Started Update UTMP about System Runlevel Changes.

 

Ubuntu 16.04.1 LTS udoo ttymxc1

 

udoo login: root

Password:

You are required to change your password immediately (root enforced)

Changing password for root.

(current) UNIX password:

Enter new UNIX password:

Retype new UNIX password:

 _   _     _

| | | | __| | ___   ___

| | | |/ _` |/ _ \ / _ \

| |_| | (_| | (_) | (_) |

 \___/ \__,_|\___/ \___/

 

 

Welcome to ARMBIAN 5.25 stable Ubuntu 16.04.1 LTS 4.4.46-udoo

System load:   1.77             Up time:       1 min

Memory usage:  3 % of 1002Mb    IP:

CPU temp:      26°C

Usage of /:    8% of 28G

 

New to Armbian? Check the documentation first: docs.armbian.com

 

 

Thank you for choosing Armbian! Support: www.armbian.com

 

Creating a new user account. Press <Ctrl-C> to abort

Desktop environment will not be enabled if you abort the new user creation

 

Please provide a username (eg. your forename):

 

<blah blah blah>

 

Now starting desktop environment...

Try one more thing. Boot from fresh, switch to developing repository and issue update:

 

https://forum.armbian.com/index.php/topic/2422-more-proper-testing-better-armbian-experience/

 

To rule out few things ...

So I did this:

 

sed -i "s/apt/beta/" /etc/apt/sources.list.d/armbian.list

apt-get update

apt-get upgrade

 

and it still boots ("deb http://beta.armbian.com $(lsb_release -cs) main utils $(lsb_release -cs)-desktop" didn't work on xenial)

Also - I updated just the custom kernel and firmware, and the board booted, so I'm guessing it's something with uboot

Also - I updated just the custom kernel and firmware, and the board booted, so I'm guessing it's something with uboot

OK, thank you. Will try to recreate and fix.

Good uboot (prior to updating custom kernel):

baudrate=115200

board_rev=MX6Q

boot_a_script=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${prefix}${script} || fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${prefix}${script}

boot_fdt=try

boot_prefixes=/ /boot/

bootcmd=mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; fi; udooinit; if run loadimage; then run mmcboot; else run netboot; fi; else run netboot; fi

bootdelay=3

bootscript=echo Running bootscript from mmc ...; source

console=ttymxc1

ethact=FEC

ethaddr=00:c0:08:88:10:2c

ethprime=FEC

fdt_addr=0x18000000

fdt_file=undefined

fdt_high=0xffffffff

image=zImage

initrd_high=0xffffffff

ip_dyn=yes

loadaddr=0x12000000

loadbootscript=run scan_dev_for_boot;

loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}

loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}

mmcargs=setenv bootargs console=${console},${baudrate} ${video} ${memory} root=${mmcroot} rootfstype=${mmcrootfstype} ahci_imx.hotplug=1

mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;

mmcdev=0

mmcpart=1

mmcroot=/dev/mmcblk0p2 rootwait rw

mmcrootfstype=ext4

netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp

netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${image}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;

scan_dev_for_boot=echo Scanning mmc ; for prefix in ${boot_prefixes}; do run scan_dev_for_scripts; done

scan_dev_for_scripts=if test -e ${mmcdev}:${mmcpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; else echo Checking here ${prefix} ... not found; fi;

script=boot.scr

splashpos=m,m

update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; fi; fi

update_sd_firmware_filename=u-boot.imx

 

Environment size: 2528/8188 bytes

 

 

 

Bad uboot (after updating custom kernel):

baudrate=115200

board_rev=MX6Q

boot_fdt=try

bootcmd=mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; fi; udooinit; if run loadimage; then run mmcboot; else run netboot; fi; else run netboot; fi

bootdelay=3

bootscript=echo Running bootscript from mmc ...; env import -t ${loadaddr} ${filesize};

console=ttymxc1

ethact=FEC

ethaddr=00:c0:08:88:10:2c

ethprime=FEC

fdt_addr=0x18000000

fdt_file=undefined

fdt_high=0xffffffff

image=zImage

initrd_high=0xffffffff

ip_dyn=yes

loadaddr=0x12000000

loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};

loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}

loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}

mmcargs=setenv bootargs console=${console},${baudrate} ${video} ${memory} root=${mmcroot} rootfstype=${mmcrootfstype} ahci_imx.hotplug=1

mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;

mmcdev=0

mmcpart=1

mmcroot=/dev/mmcblk0p2 rootwait rw

mmcrootfstype=ext4

netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp

netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${image}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;

script=uEnv.txt

splashpos=m,m

update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; fi; fi

update_sd_firmware_filename=u-boot.imx

 

Environment size: 2116/8188 bytes

 

 

I did a diff and updated all the variables to match the good uboot, and the new kernel loaded, however I don't see one wire..  I'll mess around more today

Find anything?

Find anything?

 

Yes. You must compile kernel by using our tools or include our kernel patches and it will work. We also fixed bugs and prepare kernel packages for our boot scenario. Just in this case everything works simply by installing the package. If not ... you need to set and adjust paths and boot scripts manually.

Yes. You must compile kernel by using our tools or include our kernel patches and it will work. We also fixed bugs and prepare kernel packages for our boot scenario. Just in this case everything works simply by installing the package. If not ... you need to set and adjust paths and boot scripts manually.

 

So I must be doing something wrong.  Just did a pull on your repo - attached are my changes:

 

compile.sh

16,17c16,17
< KERNEL_ONLY=""				# leave empty to select each time, set to "yes" or "no" to skip dialog prompt
< KERNEL_CONFIGURE="no"			# change provided kernel configuration
---
> KERNEL_ONLY="yes"				# leave empty to select each time, set to "yes" or "no" to skip dialog prompt
> KERNEL_CONFIGURE="yes"			# change provided kernel configuration
27c27
< KERNEL_KEEP_CONFIG="no"			# do not overwrite kernel config before compilation
---
> KERNEL_KEEP_CONFIG="yes"			# do not overwrite kernel config before compilation
31c31
< FORCE_CHECKOUT="yes"			# ignore manual changes to source
---
> FORCE_CHECKOUT="no"			# ignore manual changes to source
 

kernel config diffs (from your repo):

3c3
< # Linux/arm 4.4.6 Kernel Configuration
---
> # Linux/arm 4.4.0 Kernel Configuration
2055c2055,2082
< # CONFIG_W1 is not set
---
> CONFIG_W1=y
> CONFIG_W1_CON=y
> 
> #
> # 1-wire Bus Masters
> #
> # CONFIG_W1_MASTER_DS2490 is not set
> # CONFIG_W1_MASTER_DS2482 is not set
> CONFIG_W1_MASTER_MXC=y
> # CONFIG_W1_MASTER_DS1WM is not set
> CONFIG_W1_MASTER_GPIO=y
> 
> #
> # 1-wire Slaves
> #
> CONFIG_W1_SLAVE_THERM=y
> # CONFIG_W1_SLAVE_SMEM is not set
> # CONFIG_W1_SLAVE_DS2408 is not set
> # CONFIG_W1_SLAVE_DS2413 is not set
> # CONFIG_W1_SLAVE_DS2406 is not set
> # CONFIG_W1_SLAVE_DS2423 is not set
> # CONFIG_W1_SLAVE_DS2431 is not set
> # CONFIG_W1_SLAVE_DS2433 is not set
> # CONFIG_W1_SLAVE_DS2760 is not set
> # CONFIG_W1_SLAVE_DS2780 is not set
> # CONFIG_W1_SLAVE_DS2781 is not set
> # CONFIG_W1_SLAVE_DS28E04 is not set
> # CONFIG_W1_SLAVE_BQ27000 is not set
4175a4203
> # CONFIG_DEBUG_UART_BCM63XX is not set

git diff from sources/linux-udoo-next/4.4-5.0.11.p7.3 (this is the only change for the whole tree):

diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi
old mode 100644
new mode 100755
index 502e741..7ad9abe
--- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi
@@ -231,7 +231,7 @@
         	compatible = "w1-gpio";
                 pinctrl-names = "default";
                 pinctrl-0 = <&w1_gpio_pins>;
-                status = "disabled";
+                status = "okay";
                 gpios = <&gpio1 21 0>; 
 	};
 };

I run my compile.sh, and install all the generated debs:

linux-firmware-image-4.4.0-udoo_5.26_armhf.deb
linux-headers-4.4.0-udoo_5.26_armhf.deb
linux-image-4.4.0-udoo_5.26_armhf.deb
linux-libc-dev_5.26_armhf.deb
linux-u-boot-next-udoo_5.26_armhf.deb

via "dpkg -i *.deb" - so I assume that it will use your tools & install your kernel patches.

 

After the install - goes straight to trying to boot off net

Leave this as is

FORCE_CHECKOUT="yes"            # ignore manual changes to source

and use

CREATE_PATCHES="yes"

Apply change to source when asked and pickup patch which will be created userpatches/patch ... this patch should be moved to appropriate dir:

userpatches/kernel/udoo-next

or move it to 

lib/patch/kernel/udoo-next

and create PR to our repository since it might be useful for others too.

 

Option which you used is working properly only on source where no patches are initially involved  ... we have to change / note this.

Leave this as is

FORCE_CHECKOUT="yes"            # ignore manual changes to source

and use

CREATE_PATCHES="yes"

Apply change to source when asked and pickup patch which will be created userpatches/patch ... this patch should be moved to appropriate dir:

userpatches/kernel/udoo-next

or move it to 

lib/patch/kernel/udoo-next

and create PR to our repository since it might be useful for others too.

 

Option which you used is working properly only on source where no patches are initially involved  ... we have to change / note this.

 

perfect - that worked!

I try this procedure (without PR) but I can't succeed, I modify this file :

./sources/linux-sun8i/sun8i/drivers/media/rc/sunxi-cir.c

 

Before compiling I have this :

[ warn ] Make your changes in this directory: [ /root/crosscompile/sources/u-boot/v2017.03 ]
[ warn ] Press <Enter> after you are done [ waiting ]

 

I paste the file, but I have :

[ warn ] No changes found, skipping patch creation

 

Where I must copy paste my "sunxi-cir.c" file ?