Other families

Been dreaming of this one for a while. Finally got a weekend to focus on it recently. I'm hoping someone is eager to take what I've done and move It along some more. Here's what we have so far. * a linux 'family' called virtual.conf * a kernel config called linux-virtual-current.config * a board called virtual-qemu.wip The result is a full HVM accelerated armbian image with a kernel compiled with all the virtio drivers for disk, network and video. Also a u-boot.bin made for qemu that can boot the image when used as the qemu bios/firmware I've ran it as a VM on ubuntu using plain qemu on a Ampere eMag box.. and using UTM (qem…

[WIP] Schematics Pros: - board vendor provides dev samples and documentation - working with latest mainline kernel - many variants by the same vendor - official SDK/BSP currently on 4.4 - no unreliable shitty Micro USB for DC-IN but GPIO by default Cons: - new platform needing more initial work - not many active developers

Hi, I'm incurring in a issue with updates of the board to Armbian 26.8. The new kernel or updates break the board connectivity gets lost, since the board boots up, the LAN port blinks but it doesn't set any IP Address. The board works in headless mode with the Debian 13 CLI UFS image, so I can't debug it using a monitor. Has anyone the same issue? How to reproduce 1.Flash the recommended Debian 13 Trixie CLI Image from Armbian Website 2.Start the board normally, in headless mode 3.login with ssh 4.set a new user account 5.Run apt update && apt dist-upgrade -y and then reboot 6.Board…

Wondering if it is possible to replace pfsense (freebsd 14) with Armbian on a netgate sg-2100 appliance? https://shop.telappliant.com/product/sg-2100-pfsense-security-gateway-appliance/ I have the version with an additional 32GB M.2 SSD and it looks like the mvebu_armada-37xx board is supported by the generic Armbian, but I struggle to get from u-boot to starting the installer from usb (used the Armbian_23.5.1_Uefi-arm64_bookworm_current_6.1.30_minimal.img), with the usbboot command. Below is the current u-boot environment. I have masked some parts with "xxxxx" and probably won't need half of these variables, as they are very vendor specific, for example netgateid etc…

It was the only image I could get working. The 25.02 doesn't boot, the older versions from the archive 23.8.1 don't work either for some reason. Unfortunately I deleted the image and the rolling release moved on to 25.02.

This post from February 2025 claims that RP5 and RPMini are supported: https://www.armbian.com/newsflash/armbian-v25-2/ however, I can't find them on the downloads page. I also don't currently own an RPMini, I am tempted to buy one but I wanted to make sure it was supported first. What's the state of support right now?

Good news. Thanks to the work of many, there is now a real opportunity to run the Armbian system with the main core on Jetson Nano, and more importantly, it is easy to integrate the image build process into the official GIT Armbian. In the near future, I plan to post ready-made images with the latest kernel 5.10.22 on the download site. To run them, you need to update u-boot to Jetson Nano. This is very easy to do, just run the latest official version of Ubuntu for Jetson Nano from the SD card, it will update itself in SPI (?) u-boot to the latest version (2020.04), after that you can run Armbian from any SD card or USB media. The new u-boot supports automatic syst…

Good Morning, I am running into an issue when trying to compile an image for a SM8250 device. Most of the process is working fine until it gets to the Grub Section, at which point I get the following error: " cp: cannot stat '/usr/lib/linux-image-6.18.24-current-sm8250/qcom/sm8250-retroidpocket-rp5.dtb': No such file or directory" I have attached the logs, and would love to know if anyone has had a similar issue when trying to build an image for any device, and if so what you have done to solve it. Thanks all in advance for the support

Hello, all, I am trying to confirm the actual status of UART support on the Banana Pi BPI-R4. Does the hardware UART work reliably and appear as a character device (e.g., /dev/uart*) under Armbian Linux? Also, what is the maximum baud rate supported by this port? And one more question: Does Armbian support the Quectel EP06 modem (LTE, mini PCIe)? Thank you in advance, SY, Serge

Greetings; I have downloaded this https://dl.armbian.com/cubox-i/Noble_current_server and verified that I got what I was supposed to (ASC, SHA). I have used a brand new usbimager to install it on various freshly formatted (brand new SD Formatter) and verified working Samsung Evo 32GB, SanDisk Extreme Plus 16GB, Extreme Plus 32GB. All the formatting, imaging and installation done on an Ubuntu 25.04 laptop. After usbimager is done, if I use the Ubuntu Disks application to look at the drive, the first partion shows as free space, which seems suspicious. When I insert the newly-set up SD cards in the Cubox-i4, I see …

I don't see it specifically listed, but does Armbian run on the Beaglebone black?

Please help. We bought a board on AliExpress, but no one provided any documentation. And I can't ask the seller for it. Can anyone share any information? It's very difficult to figure out which pin goes where without documentation on the circuit diagrams. But given my situation, I set up two Ethernet interfaces. I haven't tested them at full capacity, but I can ping from both networks... myd lt527m 16e2d 180 e sx Thanks a lot.

Hello Armbian team, I am working with the TQ mba8mpxl-ras314 (i.MX8MP) board and trying to use an LVDS display: AUO G150XAN02.0 (1024×768). I have built Armbian from source using: ./compile.sh build \ BOARD=mba8mpxl-ras314 \ BRANCH=current \ RELEASE=jammy \ BUILD_DESKTOP=yes \ BUILD_MINIMAL=no \ DESKTOP_ENVIRONMENT=xfce \ DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base \ KERNEL_CONFIGURE=no I created a custom LVDS DTS overlay with the correct timing from the display datasheet (65 MHz pixel clock, 1024×768, proper porch and sync settings), and added it to However, after booting the image, the LVDS output still sta…

Hi all, I got my hands on an Odroid XU4 and wanted to use it as a replacement for my RPi 3 for all my amateur radio related stuff. Unfortunately all of the AX25 kernelmodules have been left out of official builds. I have a commit ready to add them back, yet I am not sure what the actual process is to submit a PR. As I understood I need to open an issue first yet I cannot figure out which category this fits in. I attached a patch file for current kernel. Thank You, Geoffrey ax25.patch

The alpha version of Armbian images for Orion O6 is available. To launch, burn to a USB flash drive, connect to Orion O6 and turn on the power (installation on NVMe has not yet been verified). The system starts automatically. Important. Image output to the monitor works only in graphical mode (in images with DE). Console output currently only works in UART, so you need a UART console or SSH connection for initial startup. Launching the desktop and displaying the image on the screen can take 30-80 seconds, depending on the speed of the media. https://disk.yandex.ru/d/gedMM0eLiURrjA Armbian-unofficial 25.05.0-trunk Noble ttyAMA2 orion-o6 …

the current filogic kernel has no info [in github] for where it was forked from, and trying to apply incremental patches from kernel.org I found it contains pieces of 6.14 in an ostensibly 6.12 branch. @chainsx might you be able to divulge where you forked it from?

I'm thinking of getting https://www.beagleboard.org/boards/beagley-ai I see there is this page for it https://www.armbian.com/beagley-ai/ I also see references to it in the code: https://github.com/search?q=org%3Aarmbian+beagley&type=code Are there any pre-built images available for it? Or would I have to build one?

Looking for Armbian_20.02.7_Cubox-i_bionic_current_5.4.28_desktop.7z – anyone can share a copy

[|] Error 1 occurred in main shell [ at /armbian/.tmp/work-5d76f14c-45ca-4630-ba99-8ded11db4ca4/uboot-write-Fhg7X/usr/lib/u-boot/platform_install.sh:6 and tracking down that platform_install.sh yields dd if="$SRC"/cache/sources/arm-trusted-firmware/mtksoc-20250212/build/mt7988/release/bl2.img of=$2 bs=512 seek=34 status=noxfer > /dev/null 2>&1; Note that cache/sources/arm-trusted-firmware does not appear to exist, and [although this may be my lack of knowing what to look for] I find no evidence it attempted to fetch this repo or build the firmware. Yes, this board is only recently submitted, so some problems may be expected. I did wait fo…

Hello, I'm developing a Custom Armbian for the RSB-4411 (the motherboard that uses like the Raise3D E2). For the moment, it's in the experimental phase because I can't get it to boot. It goes CRC-ERROR when I boot into the debug port on my motherboard. Source codes Armbian build: https://github.com/AstromanGaming/build Linux Kernel: https://github.com/AstromanGaming/Linux-i.MX-Fork U-boot: https://github.com/AstromanGaming/U-boot-i.MX-Fork If someone or I manage to make it boot, that would be great! 🙂 PS: I'm new to this community, if I do something wrong, please let me know.

Greetings to all; For a few hours now, as of today 2025-05-29 1418 North America/Pacific, I have been unable to update apt, receiving the following two error messages: E: Failed to fetch http://beta.armbian.com/dists/bookworm/Contents-armhf File has unexpected size (2085376 != 51213). Mirror sync in progress? [IP: 23.186.113.5 80] E: Failed to fetch http://beta.armbian.com/dists/bookworm/Contents-all File has unexpected size (44878 != 8029). Mirror sync in progress? [IP: 23.186.113.5 80] I suppose it is possible that the "mirror sync" mentioned is taking a very long time, but this seems unlikely to me. Does anyone have any ideas…

Hi. i've compiled udoo quad image using armbian build framework. The kernel is 6.x.x. When i boot the image on sdcard, usb ports don't start: the mouse's led don't turn on and keyboard too. What can i do to solve this problem? what paramaters do i have to enable? thanks

Hi All, Looking for assistance with getting an old SmartQ5 Mobile Internet Device running with Armbian. I was able to locate Github page (https://github.com/tpruvot/smartq-magicsd) which references booting from SD but need assistance getting armbian compiled and configured for the device. Any help is appreciated! SPECS: Samsung Mobile Application Processor S3C6410 based on ARM11 core at 667 MHz/800 MHz 128 MB DDR 133/333 MHz SDRAM 1 GB NAND FLASH (256 MB usable for storage) AC97 audio codec & PCM 24-bit audio SoC graphics unit, OpenGL ES 1.1/2.0, 4M triangles/sec @133Mhz (Transform only) Integrated Wi-Fi 802.11b/…

Hello everyone! I'm trying to install nvidia graphic card driver to the Jetson Nano after I successfully started bookwork on it. I have nouveau running and I don't understand how/if it is possible to switch to nvidia one. Can you guys please help me to understand whether it is possible at all? Am I missing something? Probably was Googling wrong keywords. For now I understand that Nvidia SDK supported by nvidia requires too old version of their ubuntu-based l4t linux which I don't like at all.. Thanks in advance!

How to Reset armbian 24.5.1 jammy, the device long time I not power on, but just now I power on can't log with ID Root & Password 1234. already many things still can't resolve it. If have any suggestion please let me know.

Hi, I'm trying to use desktop community build for Windows dev kit 2023 but it is not working. Current image: Armbian_community_24.8.0-trunk.554_Wdk2023_noble_wdk2023_6.7.0-rc6_gnome_desktop.img.xz When using etcher to flash to usb, it will flash but fail at validation step say "Cannot validate, the image could be corrupt" or something like that. If still use that usb in WDK, it won't boot. The lite version Armbian_community_24.8.0-trunk.554_Wdk2023_bookworm_wdk2023_6.7.0-rc6_minimal.img.xz is still working fine.

Hello, for the past few days I've been trying to install k3s on a Jetson Nano machine with the legacy Kernel 4.9, which I managed to recompile with EBPF support, but it seems there are some Kernel EBPF errors. So, I tried to install Armbian, which also doesn't have EBPF support compiled into the Kernel. I've tried to boot from many images from the Jetson Nano archive on the Armbian site, but none of them work. Is there any documentation on how I could compile the kernel on Armbian - Jetson Nano machine? Why can't I boot from any of the Armbian - Jetson Nano images from the archives? I have updated the legacy OS from Nvidia with the latest drivers boot loaders …

Not sure if this should go in this section, but since my problem is about non-supported board, then I guess... I found out about Armbian only recently and decided to give it a try for my T113-S3 based board I bought on Aliexpress. It looks like it's some kind of a MangoPi MQ clone, at least judging by schematics. I managed to create a new configuration for my board, together with required U-Boot patches. I built two images, for "current" and "edge" kernel. For some time I was under impression that Linux doesn't boot at all (serial console output was stuck at "Starting kernel ..."), until I added earlycon=on to armbianEnv.txt. Then I finally saw some outpu…

Hello good people, I recently started "porting" linux to my Huawei mate 9. Its one of those projects plagued with silly issues and a sad lack of docs and unreliable hearsay. I was hopeful someone may have started something similiar, or maybe commit logs/discussions from when Hikey960 support was added. Ive found commits but praying that maybe more exists. I just have a handful of basic questions, most unfortunately involve things like the android bootloader. Which partitions related to boot can safely be replaced with non signed images, how do i stop fastboot from combining the appended dtb with those in dts partition. Just to give a general sense of what im l…

Hi, I'm trying to generate an Armbian image for a custom board. I generated configuration files for card and family, with the necessary information for u-boot and kernel. I need to have separate boot partition in FAT and I added BOOTFS_TYPE="fat". Using the compile.sh in the Armbian "build" repo I get an image, but flashing it on the sdcard does not start uboot. In the boot partition I find not only the kernel and dtb, but also the u-boot scripts. How do you generate an image that contains everything correctly? Thanks in advance Riccardo

Hi There, I would like to run Linux5 or Linux6 on Jetson nano, display using HDMI-DVI adapter. It worked fine with Jetpack4 (=Linux4). When I boot with armbian/Linux5.10, which is linux-image-current-jetson-nano, the display tells me it is out of sync then I would force the display as 1280x1024@60Hz, since it looks like Linux fb or X11 are trying to use 1280x1024@75Hz, so that I need edid/1280x1024.bin (maybe with video=1280x1024@60) using {linux-source}/tools/edid to maintain the resolution and sync. I tried both of gcc-10 and gcc-9 to build it, but failed with below error: edid.S: Assembler messages: edid.S:274: Error: cannot represe…

Hi Friends Recently I have been trying Armbian 23.5 as alternative for NVIDIA official images. Tried both Ubuntu Gnome desktop and Debian Cinnamon desktop builds but somehow non of them discovers HDMI output. When Jetsno Nano is booting up I can see official "NVIDIA" screen for a while and then information about missing input (from TV on a TV). The hardware itself works OK - when I change SD card to one with an official image or another one with Debian 11 official - it works just fine. It's seems like a problem with Armbian build itself. Any advice is much appreciated. Kuba Logs: https://paste.armbian.com/omiher…

Foreward: Not sure if this better fits in board bring up, but I can't post there, so feel free to move if appropriate. I'm looking into the feasibility of using the Armbian build system to generate OS images for the Avnet MicroZed board. This board is based on the Xilinx Zynq 7000 platform, which is a SoC made up of a dual core 500 MHz CPU, and a Artix-7 generation FPGA. The CPU is nothing to write home about, but the FPGA opens up an interesting array of possibilities. Just in case you need an ARM board with 100+ GPIO, over two dozen serial ports, or your own function generator. Really, you're limited only by pin count, FPGA fabric usage, and what you can man…

Greetings - I took the contents of the Armbian_23.8.1_Jetson-nano_bookworm_current_6.1.50 image and put it on my NFS server in an attempt to network boot my Jetson Nano device. After making some adjustments to the pxelinux.cfg so that it points to the correct files on my tftp server, the device fails to boot with the following u-boot output: Tegra210 (P3450-0000) # pxe boot 1: Armbian Retrieving file: /boot/jetson-nano-1/uInitrd Using eth_rtl8169 device TFTP from server 192.168.123.4; our IP address is 192.168.123.38 Filename '/boot/jetson-nano-1/uInitrd'. Load address: 0x83200000 Loading: #############################################################…

Are there any other Mekotronics R58 mini users out there? I like this box a lot and Armbian runs great on it, I would very much like to share expereriences with other users and learn from each other. At this point Armbian is downloadable for this board on this site. And it has recent updates too. Some specs: I have the Mekotronics R58 mini plastic version (there is also metal box that has better cooling but same internals) RK3588 8 core Rockchip CPU 4Gb RAM File System transferred to 120Gb SSD with armbian-config Measured it uses 2.1 watt during idle I seem to have everything working except HW acceleration. On the download page…

Hello, I have an orange Pi i96, and I can't find a USB device. In /dev, I have a serial folder, then by-id in which I have : usb-1a86_USB_Serial-if00-port0 But it doesn't disappear when I remove the USB device ... And the USB output doesn't change whether the device is plugged in or not. Dmedg gives nothing related to usb and lsusb gives this: Bus 001 Device 002: ID 1a86:7523 QinHeng Electronics CH340 serial converter Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And it doesn't change depending on whether the USB port is busy or not. Am I missing something? Have a nice day I know it's the wrong ta…

Dear Armbian Team, I have a BPI M64. all the images for BPI m64 have "Audio Codec" except the armbian image. so i cannot configure my 3.5 audio jack because it needs "Audio Codec" card in alsamixer. i cannot hear any sound from the jack because it needs to be configured with alsamixer over the "Audio Codec" card. there is only sun50i-a64-audio and sun9i-hmdi. but no "Audio Codec". can you give me any solution?

i have already install pihole + unbound on this device now i want to reset everything so i can make a new project on it because of the limitation on storage.. can i know how to do that? and without change any kernel/firmware i'm beginner on linux ecosystem...

Dear Armbian community I want to run klipper on my ordoid n2+ I started out using a default ubuntu os from odroid themselves but it was missing a ton of drivers I need. everything worked on that image except for the drivers. Someone mentioned Armbian to me. I got everything running except I now have a new issue. I am using klipperscreen a simple gui with touch controls. before installing I could use my screen without issues and I installed everything on the screens terminal. Now that klipperscreen is installed I see the boot sequence and than the signal gets lost. I already checked the klipperscreen guides and forums and if it doesnt report errors its the…

Hi. I am working with an Olinuxino A20 micro, but I have issues with the SPI bus. I hope somebody can help me to find a solution. I used Armbian 23.5 Bookworm with kernel 6.1 In sclk signal i have a pulse before to start the data transmission, I required the SPI to communicate a LoRa module but the pulse before of data generate that doesn´t work the LoRa module. I attached the signals.

I have followed all threads dealing with this topic but got no where so maybe... just maybe someone has made it work somehow? I have armbian (Armbian_23.02.2_Rk3318-box_bullseye_current_5.15.93) installed on a TV box with a Rockchip RK3318 inside it. I am using a microsd card and EVERYTHING is running wonderfully! I have also attached a 500GB USB hard disk (output from fdisk-l) Disk /dev/sda: 465.76 GiB, 500107862016 bytes, 976773168 sectors Disk model: 5000BEV External Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes I ran armbian-config a…

I've tried two releases of Armbian for the Jetson Nano and was struggling to get SPI enabled on the Jetson. To check if SPI is enabled, I've been reading its status is through: cat /proc/device-tree/spi@7000d400/status which just returns disabled Here's what I tried: - enabling spi-spidev through armbian-config, but this option doesn't exist in armbian-config as it does for other releases for devices - making a custom device tree dts file and pointing extlinux.conf to it (below is the relevant snippet): spi@7000d400 { compatible = "nvidia,tegra210-spi\0nvidia,tegra114-spi"; reg = <0x00 0x7000d400 0x00 0x200>; inte…

I cloned the quite latest version of Armbian: commit 369e69a55390f59c2299c98c09bf3d805ac59335 (HEAD -> main, origin/main, origin/HEAD) Author: Ricardo Pardini <ricardo@pardini.net> Date: Mon Apr 3 13:15:54 2023 +0200 artifact-armbian-bsp-cli: hash more variables included in `/etc/armbian-release` Using the edge branch to compile for my renegade board, which has the rk3328 chip: ./compile.sh BOARD=renegade BRANCH=edge RELEASE=bullseye BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_CONFIGURE=no COMPRESS_OUTPUTIMAGE=sha,img It blocks when start to boot the kernel: U-Boot 2022.07-armbian (Apr 17 2023 - 23:29:15 +0800) Model: Firefly roc-rk332…

Hi, when booting Armbian Sid minimal rolling 6.1.11, there is no serial console login. Console output: Found U-Boot script /boot/boot.scr 1993 bytes read in 146 ms (12.7 KiB/s) ## Executing script at 12000000 93 bytes read in 94 ms (0 Bytes/s) 38318 bytes read in 2603 ms (13.7 KiB/s) 33621022 bytes read in 3482 ms (9.2 MiB/s) 11215360 bytes read in 1257 ms (8.5 MiB/s) ## Loading init Ramdisk from Legacy Image at 14800000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 33620958 Bytes = 32.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flatte…

When I take an image with the camera ( Camera V2 raspberry) with the pygame or cv2 module, I get a green screen. I looked for several documentations to solve this problem but never anything very specific. Do you have any idea?

I'm currently working on getting a custom kernel (5.4 kernel which was modified for a specific need regarding containers) running on a Jetson Nano. I've tried running the kernel image on NVIDIA's Jetpack but that didn't work. I've tried building the image directly on the Nano running Armbian and it hasn't really worked so far. It seems to either brick the Nano or not update the kernel version after an install (depending on if I replace /boot/Image). Would you all have any suggestions of what I can try or if it’s even possible? Thanks in advance!

U-Boot 2017.05-armbian (Nov 30 2022 - 10:45:39 +0000) for ODROID-XU4 CPU: Exynos5422 @ 800 MHz Model: Odroid XU4 based on EXYNOS5422 Board: Odroid XU4 based on EXYNOS5422 Type: xu4 DRAM: 2 GiB MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 MMC Device 0 ( SD ): 59.5 GiB Card did not respond to voltage select! mmc_init: -95, time 11 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Press quickly 'Enter' twice to stop autoboot: 0 ** File not found /boot.ini ** ## Executing script at 43e00000 Wrong image format for "source" command 12548 bytes read in 44 ms (278.3 KiB/s) ## Executing script at 43e00000 111 by…

Hello, first of all thank you for the development of the Armbian software. I am currently using version Armbian_22.08.2_Uefi-x86_bullseye_current_5.15.69 on my Terramaster F5-221. Unfortunately I have two small problems. Firstly, there is no linux header for the kernel used for compiling. Secondly, unfortunately I can't add a network interface in openmediavault. That always gives me an error. It works on Debian with Openmediavault. unfortunately this surprises me. Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LANG=C.UTF-8; export LANGUAGE=; omv-salt deploy run --no-color systemd-networkd 2…

What is the baud rate of s905w

I am trying to compile the full OS image (incl. kernel and u-boot) for nanopifire3 target but fail every time. I am following the provided build instructions. I have tried compiling on multiple machines, but the one I am using has 8 cores and 12gb RAM. I have tried in an Ubuntu 22.04 LXC container, Ubuntu 22.04 in a VM, and the the docker container provided by Armbian. My kernel has the binfmt_misc module loaded (verified with lsmod), no spaces are present in build path, and I have tried both root user and sudo as a regular user. I have also checked the similar issues on the armbian forum Please forgive me if anything is incorrectly formatted or so, I have…

Trying to debug this issue. Everything was fine until a recent reboot and now the box is stuck in a boot loop with any supported image downloaded from armbian. I've been focused with debian but the ubuntu doesn't work either. I have tried 3 different microSD cards (samsung and SanDisk) with the same result. I've tried the steps in https://docs.armbian.com/User-Guide_Basic-Troubleshooting/ https://docs.armbian.com/User-Guide_Recovery/ but it appears that the there is something going on with the Linux kernel? changing the verbosity doesn't provide any new information. I have even tried 20.05.1 and still the same behavior. Any though…

Hello everone. I'm new to embedded linux. To start with, I have nanopi fire 3 and smart 6818 cards, but I cannot access gpio pins with any gpio library. Why doesn't the NPi-GPIO library work with these cards? At first I was using the lubuntu version, I tried a lot there, but I couldn't. Now I'm trying to do something using armbian version 21.04. I'll post the problem I'm facing below. Thank you in advance for your help. Traceback (most recent call last): File "npigpio.py", line 1, in import NPi.GPIO as GPIO File "/usr/local/lib/python3.7/dist-packages/NPi.GPIO-0.5.8.6-py3.7-linux-aarch64.egg/NPi/GPIO/init.py", line 1, in from NPi._GPIO import * Runtime…

Hi, I'm so happy to growth of Armbian, and its good to see that you adding new devices to your device support cartela. But I couldn't find CSC image for Tinkerboard 2. Is that uses same image with RockPi N10 or did you forget to add to download page under to CSC images lists. Bests,

Hello I downloaded Armbian for a CuBox i4P from https://redirect.armbian.com/region/EU/cubox-i/Bionic_current_desktop. uname -a reports: Linux cubox-i 5.10.12-imx6 #21.02.1 SMP Wed Feb 3 21:02:35 CET 2021 armv7l armv7l armv7l GNU/Linux However this image is working really fine, for a 7yo hardware. Thank you, Developers 2D software rendering is fast, Desktop windows are transparent. Great work! I tried Armbian Focal desktop mainline first, but it didnt show the desktop never again after first reboot, so i was happy with Bionic! Found similar problem here and i think i just need the correct xorg driver. Thanks for a…

Upgrading cubox-i Armbian Buster from kernel 5.7.x to Kernel 5.8.y breaks ethernet and I'm unable to get it connected again. Works fine again downgrading back to 5.7.y. This occurs on multiple cubox-i devices. System diagnosis information will now be uploaded to http://ix.io/2zH6 dmesg | grep eth0 [ 4.667327] fec 2188000.ethernet eth0: registered PHC device 0 [ 22.369472] fec 2188000.ethernet eth0: Unable to connect to phy nlcli wlan0: connected to sketch-wlan "Broadcom BCM4330" wifi (brcmfmac), 6C:AD:F8:1D:36:25, hw, mtu 1500 ip4 default inet4 10.1.0.41/22 route4 0.0.0.0/0 …

Hi: I recently installed Buster xfce desktop on Cubox i4pro. Everything works great, except I can not power off cubox. I tried various commands, shutdown -h now; systemctl poweroff; and hatl; but the system first appears to halt, where I can not ping the ip addrss of cubox, but then it reboots. Is there some way to powerfoff cubox? My current system is nightly, but I also tried stable with latest kernel. $ uname -r 5.10.21-imx6 $ cat /etc/os-release PRETTY_NAME="Armbian 21.08.0-trunk.26 Buster"

Hi! For some reason my nanopi fire 3's gigabit ethernet is very unstable. When connected to my local machine directly, the ping latency is insanely high and irregular: PING 10.42.0.101 (10.42.0.101) 56(84) bytes of data. 64 bytes from 10.42.0.101: icmp_seq=1 ttl=64 time=112 ms 64 bytes from 10.42.0.101: icmp_seq=2 ttl=64 time=333 ms 64 bytes from 10.42.0.101: icmp_seq=3 ttl=64 time=350 ms 64 bytes from 10.42.0.101: icmp_seq=4 ttl=64 time=203 ms 64 bytes from 10.42.0.101: icmp_seq=5 ttl=64 time=1014 ms 64 bytes from 10.42.0.101: icmp_seq=6 ttl=64 time=423 ms 64 bytes from 10.42.0.101: icmp_seq=7 ttl=64 time=93.4 ms 64 bytes from 10.42.0.101: icmp_seq=8 ttl=64 time…

Hello! I'm trying to boot latest releases of of Armbian (following images: Armbian_21.02.3_Cubox-i_buster_current_5.10.21.img and Armbian_21.02.3_Cubox-i_focal_current_5.10.21.img) on a Solid-Run Hummingboard2 Gate V1.4 board. (Board V1.2 freeze during Uboot) I'm getting to the "Starting kernel" message but after that things stop. Switching on the verbose output in ArmbianEnv.txt result in the output below where the kernel always stop at message: [ 0.000000] Freeing unused kernel memory: 2048K Do anyone have any thoughts/ideas here on what could possibly be the problem stopping the kernel from booting? U…

Hello, I have recently tried a more recent kernel 5.10.x for my HummingBoard with imx6 solo. After playing with GPU/OpenGL acceleration I have noticed that there is no H.264/MJPEG Video acceleration present in the kernel. The video codec Chips&Media 960 driver module (kernel option VIDEO_CODA) is simply not build in. Why is that? Can it be enabled by default for future IMX6 builds? Thanks for your support!!

Could someone list the differences between the i.MX6 based CuBoxes? I've seen this ones mentioned: CuBox-i1 CuBox-i2 CuBox-i2eX Cubox-i 4x4 CuBox-i4Pro CuBoxTV Are there more?

Hi Guys, First thanks fo rthe hard work, but as in other threads here every now and again we get an issue moving up kernel versions. Mostly this is a post to flag up I had issues, so might you and that reverting the kernel fixed it for me. I did an apt-get update; apt dist-upgrade (I run this every other day normaly) and it did a kernal update from Linux cubox 5.9.14-imx6 #20.11.3 SMP Fri Dec 11 20:57:51 CET 2020 armv7l GNU/Linux to Linux version 5.10.12-imx6 It appears to all work.... however I use my Cubox-i to be a server for Kodi. When I play flac files (which are quite big) it down loads th…

Hi, My Solidrun Cubox I1-300-D has been running Armbian for quite some time (Samsung EVO SD card). However, I tried to update/upgrade, and my version was non-supported anymore (19.04?), so time for a fresh new image. I've tried three times (download image from https://www.armbian.com/cubox-i/, sha256 check, burn image with etcher, inspect file structure (looks good), and boot), but each time this happens: "Armbian universal operating system" + text ("Executing script at ...") splash screen, then a black screen, and then my TV says "no signal", and then nothing anymore. At the ethernetconnector, there is red LED on / flashing…

Hi I tried both latest cubieboard images, Fokal and Buster, both stops booting here: U-Boot SPL 2020.10-armbian (Nov 23 2020 - 16:05:27 +0100) DRAM: 1024 MiB CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2020.10-armbian (Nov 23 2020 - 16:05:27 +0100) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech Cubieboard I2C: ready DRAM: 1 GiB Yes, I tried different power supplies and SD cards. Any idea what could I do? Thans Chris

Hello, I deployed the latest image "Armbian Buster mainline based kernel 5.8.y" and after initial setup, I cannot activate the analog sound card. What I did: The "Hardware" section in "Settings" section of armbian-config was missing, so I installed the following packages: "linux-dtb-current-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.9.5-sunxi, linux-dtb-dev-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.10.0-rc2-sunxi" and after that changed: /boot/armbianEnv.txt by adding overlay_prefix: "sun8i-h3". This was the only way I could make armbian-config to correctly display the "Hardware" device tree. I tried to put: i…

I have a v1.2 Rockpi S with 512MB of RAM, while using the latest Armbian Focal and Buster images (20.08.1 with kernel 4.4.y), I have been experiencing WIFI issues. The device connects to the Access Point and maintains the connection but every minute or two the SSH connection hangs or freezes for several seconds and then comes back and prints everything that when on during the period it was not responsive. When I used the images with the 5.8.y kernel, I did not experience the same issue. In all cases wired ethernet (eth0) is not effected by the issue. Continuously pinging a local system shows the below result. Other WIFI devices on the same network do not experience …

Hi. I have a bunch of HummingBoard2 boards that have been used by a company called Vivo. Basically they allow schools to transfer video through Ethernet to monitors and projectors. I also want to do this but Vivi is a subscription based system so that SUX! I therefore want to blow Vivi away and load a clean Armbian. My issue is that the boards have no SD cards soldered to the board. They have power, 2xUSB, RJ45, HDMI connectors. They must therefore boot from eMMC. I found info on the board manufactures website., SolidRun, on how to use jumpers to select boot type. It was set to eMMC so I set it to USB and flashed a SD card with Armbian 20.20 and rebooted…

I am looking for ways / support to run Armbian (no release preference; any version would be good) on the tolino epos 1 eInk display eBook reader (built by taiwanese manufacturer Netronix under model ID 37NB-E70Q2M+4A2). The device currently/by default runs Android 4.4.2. I'm able to flash customized 4.4 images via fastboot and have ADB control (Android Debug Bridge) via USB and Wifi. I've identified the following key components: Freescale i.MX6 SoloLite (MCIMX6L8DVN10AB) CPU. Version with GPU and EPDC (Electrophoretic Display Controller; a feature-rich, low power, and high-performance direct-drive, active matrix EPD co…

I'm trying to upgrade from Armbian 5.32 (Xenial Next/4.4.76) and was hoping to enable 1 wire again on my Udoo. For that build, I had to add one wire modules to the kernel config, then edit the imx6qdl-udoo.dtsi to set the onewire status to okay (from disabled). In the dtsi, after udoo_ard: udoo_ard_manager it had: onewire@0 { /* example for pin 08 */ compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&w1_gpio_pins>; status = "disabled"; /* "okay" to enable */ gpios = <&gpio1 21 0>; }; and in iomuxc, there was a section (in external_hog: hoggrp-2, MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x800…

I downloaded Armbian for a Udoo Quad from https://dl.armbian.com/udoo/Focal_current_desktop. uname -a reports: Linux udoo 5.6.18-imx6 #20.05.4 SMP Mon Jun 15 00:30:23 CEST 2020 armv7l armv7l armv7l GNU/Linux However in https://docs.armbian.com/Hardware_Freescale-imx6/ I read: "Udoo Quad Kernel 3.14.x and 4.4.x with some hardware support, headers and some firmware included", which suggests that the image should have a 3.14 or 4.4 kernel. In /var/log/Xorg.0.log I read: [ 21.345] (II) AIGLX: Screen 0 is not DRI2 capable [ 23.279] (II) IGLX: Loaded and initialized swrast [ 23.279] (II) GLX: Initialized DRISWRAST GL provider for screen 0 LIBGL…

I've recently upgraded Armbian on my Cubox-i using apt, i.e. that was not a new clean install. As a result I still have an old kernel running. What is the right way to upgrade kernel? Edit: updated using armbian-config, everything seems to be ok.

UDOO Quad Hello. Armbian bionic desktop mainline based kernel 5.4, USB ports do not work, wifi module is not visible. Everything works correctly on Stretch. Do not tell me where to look for the reason?

I'm using a mpci wireless card. Previous versions of armbian detected the card without problems. Buster does not. lspci returns nothing.

Hi, I am making Asterisk PBX over Orange Pi - 2g IoT, I have tried Armbian as well as Ubuntu. Everything is working fine, but I am stuck on two issues, a. How to add built-in GSM module of Orange Pi 2g IoT board in asterisk, so that A GSM trunk call/text can be transferred on SIP extension. I know chan-dongle, but asterisk is not detecting GSM module. I ahve tried different versions of asterisk. b. How to change IMEI of Orange Pi 2g IoT Looking for solutions Regards

Hello, I'm trying to get working my NanoPi Fire3 with HD702 screen and I found out some issues. I'm running Armbian_20.02.7_Nanopifire3_bionic_legacy_4.14.174 image on it. -- First and most significant is that the ethernet port isn't working properly. I cannot ping anything and if I try to deactivate and activate ethernet connection in Network Manager it says: Error: Connection activation failed: IP configuration could not be reserved (no available address, timeout, etc.) Mar 31 14:04:05 nanopifire3 NetworkManager[3061]: <warn> [1585663445.9567] dhcp4 (eth0): request timed out Mar 31 14:04:05 nanopifire3 NetworkManager[3061]: <info> …

I am trying to set up Armbian as an iSCSI initiator using open-iscsi. The result is Mar 15 03:07:13 matrix iscsid[2207]: iSCSI logger with pid=2208 started! Mar 15 03:07:13 matrix systemd[1]: iscsid.service: Failed to parse PID from file /run/iscsid.pid: Invalid argument Mar 15 03:07:13 matrix iscsid[2208]: iSCSI daemon with pid=2209 started! Mar 15 03:07:13 matrix iscsid[2208]: can not create NETLINK_ISCSI socket Mar 15 03:08:43 matrix systemd[1]: iscsid.service: Start operation timed out. Terminating. Mar 15 03:08:43 matrix systemd[1]: iscsid.service: Failed with result 'timeout'. with a timeout of around 90 seconds. I'm running the kernel Li…

Hello could someone point me in the direction of the stretch images if they are still hosted here of course. I want to run omv and i just found out what is happening with omv5 and armbian the past year. So ill go stretch and omv4. Kind regards Oliver

when i changed to run the current kernel 5.4.12 the ethernet would work ok, then while transfering over smb/samba to my windows 10 box the ethernet would totally drop, as in the light on my switch went out, not just dropping a few packets!! The only thing that fixed it was to rever "back" to 5.3.11-imx6. Note the change both up to the 5.4.12 and then back to 5.3.11 were performed via the armbian-config tool. (the system is running headless, and the log file does include a boot of "Linux version 5.3.11-imx6" as well as the working 5.3.11 Is anyone else seeing this? JB.

I am developing on an imx6 board that is no longer in production. It has a full Yacto-based build system that works, based on an old 3.17?) kernel, but its a pain to develop for. It's not worth spending too much time on refactoring the image, but I'm wondering how big of a job it might be to build an Armbian image for it, given that I already have a working uboot and kernel. The hardware just uses a couple of usbs and uarts, and a pcie wifi card. One wersion also has an hdmi encoder, another has hdmi display. Those might be the hardest to support, but driver support is in the kernel. Thoughts? Sent from my LM-G710 using Tapatalk

Here's what I get when trying to boot (data is from my serial adapter): I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error Wakeup Sub CPU 1234567 CPU Wakeup done! WFI is expected. CPU0 is Master! U-Boot 2016.01-armbian (Sep 02 2019 - 08:57:37 +0200) DRAM: 1 GiB MMC: NEXELL DWMMC: 0, NEXELL DWMMC: 1 loaded from SD, getting env from MMC 1 *** Warning - bad CRC, using default environment MIPI: display.0 HDMI: display.0, preset 0 (1280 * 72…

Hi, coming from "ARMBIAN 5.73 stable Ubuntu 18.04.2 LTS 4.19.20-cubox" after performing apt udate apt upgrade my cubox won't boot anymore. I've no idea how to recover from this. The output from boot is in the attached picture. What can I do?

I've got a CuBox i4P with an external SSD connected via eSata and has an external power supply. The 960GB SSD isn't recognised on the system: df -aTh Filesystem Type Size Used Avail Use% Mounted on sysfs sysfs 0 0 0 - /sys proc proc 0 0 0 - /proc udev devtmpfs 869M 0 869M 0% /dev devpts devpts 0 0 0 - /dev/pts tmpfs tmpfs 202M 8.1M 194M 5% /run /dev/mmcblk1p1 ext4 15G 1.2G 14G 8% / securityfs securityfs 0 0 0 - /sys/kernel/security selinuxfs selinuxfs 0 0 0 - /sys/fs/seli…

Hi, After a power shutdown, my Cubox-i 4 Pro does not boot anymore. I am running on it Debian Stretch since years. My system is on a hard drive (/dev/sda1). It seems that the boot process is blocked in a loop, as each time, just after: Starting kernel ... Uncompressing Linux... done, booting the kernel. ...U-boot is restarting as after a fresh reboot. My boot.txt: $ more armbianEnv.txt verbosity=7 rootdev=/dev/sda1 console=serial usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Here is the bootlog: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-b…

Hi everyone, Armbian works well for me on a NanoPi Neo, and installing it on my Cubox i4 was straightforward... but I'd like to try a kernel newer than linux-image-cubox (version 4.14), to get improved video support, and both linux-image-dev-cubox (version 5.2.11) and linux-image-next-cubox (version 5.1.16) do not provide any video output at all. I've uploaded the armbianmonitor report from booting the linux-image-dev-cubox kernel. Help on this would be appreciated!

I am currently using Solidrun SbC (ICUBOX and HUMMINGBOARD) and a couple of weeks ago I updated UBUNTU on the Hummingboard to release 18.04 and lost internet..no more network. So try to fix that with no success so after many hours I decided to rebuild the OS with Armbian Buster but I cannot boot from my sd card (sd was flashed with Etcher). So did a surface check with no problems found. I thought it was power supply but I can boot from Android (Cubox and Hummingboard ) so PS should be good. My sd cards are Sandisk extreme 16 gigs. Since I did not build a bootable sd card since 3 years ago, I must have done something wrong but I don’t know what? Does the sd has to be form…

Hello, I wanted to test wireguard with my cubox i4, but I'm not able to load the module. I tried to search the net for this error, but fond nothing useful. Maybe someone has an idea. Thank you Michael uname -a Linux loki 4.19.41-cubox #5.85 SMP Wed May 8 15:52:55 CEST 2019 armv7l GNU/Linux dpkg -l | grep linux ii console-setup-linux 1.164 all Linux specific part of console-setup ii libselinux1:armhf 2.6-3+b3 armhf SELinux runtime shared libraries ii linux-base 4.5 …

To Igor Bit not understand why new 5.44 for nanoPC T3 plus not run. I see only first boot screen and then black always ???

Hello, Recently I bought a nanopi fire 3 and installed armbian without any issue (Armbian_5.91_Nanopifire3_Debian_buster_next_4.14.133). The first thing I did was to connect the nanopi to my ADSL router in order to complete the basic configuration. Everything worked fine. Then I connected the nanopi to an Edimax gigabit ethernet switch and here is where the network problems appeared. The ethernet connection was too slow, with ping times of more than 1000ms, and an unstable behavior that made it almost impossible to connect via ssh. 64 bytes from 192.168.22.12: icmp_seq=1 ttl=64 time=1004 ms 64 bytes from 192.168.22.12: icmp_seq=2 ttl=64 time=1…

Sorry to be back here I run a Cubox-i. I upgraded to kernel 5.1.16 yesterday. Then I rebooted and everything was running fine. But today my server looked dead: none of my services was answering, no way to ssh to the cubox... I tryied a hard reboot with no success. Here is the log on a putty console: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6-CuBox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - b…

I just switched from iptables to netfilter. After a reboot I get this kind of status for the service systemctl status nftables ● nftables.service - nftables Loaded: loaded (/lib/systemd/system/nftables.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2019-07-12 16:04:59 CEST; 4min 28s ago Docs: man:nft(8) http://wiki.nftables.org Process: 287 ExecStart=/usr/sbin/nft -f /etc/nftables.conf (code=exited, status=3) Main PID: 287 (code=exited, status=3) Jul 12 16:04:59 cubox nft[287]: netlink.c:62: Unable to initialize Netlink socket: Protocol not supported Warning: Journal has been rotated since unit was…

Until now, the path '/sys/class/leds/imx6:red:front' was used to control the LED on Cubox. Since the last update the path no longer exists. Anything I can do?

Hello (sorry, I am writing through a translator) I have a Zyxel NAS326 with a physically damaged NAND - it does not save the device configuration. board photo: Because I do not have access to the programmer, I want to replace NAND and program it in the NAS. However, I can not run U-Boot via UART. I tried the adapters on PL2303HX and FTDI FT232RL. I'm using a kwboot on this topic: and the u-boot file from this: https://forum.doozan.com/read.php?2,27108,31893#msg-31893 Every time this error pops up: root@gutek3:/gutek/nas326# ./kwboot-x86_64 -f -t -B 115200 /dev/ttyUSB0 -b uboot.bin -s 0 -q 1 Sending boot message. Please reboot the …

I need help please, I am working on NanoPCt3 board based on Armbian_5.83_Nanopct3plus_Ubuntu_bionic_next_4.14.115_desktop I put static ip to eth0 and when i try to ping the output in not stable: 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=1 ttl=58 time=580 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=2 ttl=58 time=120 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=3 ttl=58 time=350 ms and then the output: Destination host unreachable. Destination host unreachable. Destination host unreachable. and i think there are some issues in kernel drivers related on Ethernet or ipv4 so could y…

Hi, Since I upgraded my kernel to version 4.19 (`linux-image-next-cubox=5.73` when I tried I think) on my cubox-i4 pro, I lost HDMI : root@cubox:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Anyone experiencing this too ? Downgrading to `linux-image-next-cubox=5.60` solved it. apt install linux-image-next-cubox=5.60 reboot aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: DWHDMI […

Hi there! I recently installed Armbian (Stretch: Armbian_5.83_Nanopifire3_Debian_stretch_next_4.14.115) on my new NanoPi Fire3. I was able to boot, but it responds so slow, that it is unusable! For example, when I SSH into it, it takes a log time to show me the login prompt. When I enter the username and press enter, it takes about 5 seconds to ask me for password. When I enter password, it takes about 10 seconds to show me the Armbian banner. I wasn't even able to go past the changing of unix password on first login, because it just "froze". I have installed the image twice on my SD card, just to make sure it isn't a corrupted install.…

Hi all, In the review of the Fire3 at least one person mentions powering this board via something other than the MicroUSB. This would allow me to use the serial console that's supposedly exposed over that port instead of wiring up yet another USB to serial converter. What I can't work out is a) which pin/s are used to power it, and b) what kind of power supply is used. I'd rather not fry the board (it'll do that itself under load) so can someone point me in the right direction? Thanks in advance.

I bought several modules with mpc8308 on board. But following the documentation, i did not manage to implement DMA data transfer. Is it possible to get an example of the implementation of data transfer over DMA?

Hi, I've just created a SD-card with Armbian Bionic (mainline kernel 4.19.y) for a Hummingboard Gate. I noticed during boot that it says it uses U-boot version 2013.10-rc4. This seems quite old compared to the 2018 version that was on the Debian Stretch image from SolidRun. I've tried to search the internet to see what the impact of something like this is and wasn't able to find something that made sense to me (could be entirely my fault). I therefore have the question: Is the U-boot version intentional? (maybe it has some features that newer versions have dropped.)

Hello I have a nanoPc t3 plus board and I cannot boot it. I searched and I found a related topic that has the same problem but there is no answer. I believe the problem is because of different mem chip but the same revision (1709) Can boot armbian whit compiled friendlyArm Uboot? topic URL my memory chip picture and logs (from the topic) \

Hi, I am running Debian Strech on a headless server with armbian (since 2014 on wheezy), on a Cubox-i 4 Pro. My system is on /dev/sda1 After an upgrade, few minutes ago, my device is no more reachable by ssh neither answering to ping. It seems to boot the kernel but I am not even sure of that (as nothing appears in the console after "booting the kernel"). Here is the full console log: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) CPU: Freescale i.MX6Q rev1.2 at 792 MHz R…

In the nanopcT3+ board I need to enable the I2S1 (14 pin header) in Desktop version. I need to have the I2S1 peripheal as SLAVE and a MCLK of 48kHz and 192kHz (better if other clock speed are supported). The "aplay -l" and "arecord -l" commands must show the I2S1 as a sound card with input ad output device. I've tried to do the job but I'm a newbbie on linux and embedded linux. Following the official FriendlyArm wiki, on a host PC I've downloaded the kernel source, modified the dtsi file to enable i2s, recompiled the kernel and U-boot and all steps seem work fine. Now I don't know how to do a final steps to have a SD bootable image with eflasher to load and test…