SBC News

This week's cycle emphasizes broad U-Boot modernization, new board and SoC enablement, and kernel and wireless driver consolidation. A large-scale U-Boot bump moves sunxi 32-bit and 64-bit targets from v2024.01 to v2026.07-rc4, with follow-on updates for self-pinned H616/H618 boards (Zero2W, Zero3, Longan Pi 3H), Mixtile Edge2, NanoPi R5S (now patch-less), and the Youyeetoo YY3588 switching to mainline v2026.04. The imx6 line (UDOO, Cubox-i) was modernized to U-Boot v2026.07 with legacy 6.12, current 6.18, and edge 7.1 kernels. Related toolchain work fixes ODROID-C1, ODROID-XU4, Recore, and X96Q builds under Trixie's GCC 14, and resolves errexit failures on Rockchip SPI b…

This week's updates center on expanded board support, Rockchip and Qualcomm platform maturation, and build system refinements. New hardware coverage grew across multiple SoC families, with the Lubancat 5IO (RK3588), KickPi K3B, Mellow Fly C5 3D printer board, and community support for the Orange Pi Zero 3W (Allwinner A733). The Arduino UNO Q advanced to mainline 7.1 on the edge kernel and gained desktop hardware acceleration via Mesa pinned to Trixie backports, while the BeagleY-AI received ISP, IMX219, and VPAC patches. Companion fixes addressed NVMe/SD boot conflicts on the NanoPi M6, Ethernet on the BigTreeTech CB1, and AIC8800 UART Bluetooth on Orange Pi A733 hardware…

This week's work centers on board portfolio expansion, kernel and U-Boot version bumps, and CI and infrastructure hardening across the build and documentation pipelines. Board support saw notable growth with the introduction of the SpacemiT K3 Pico-ITX and Luckfox Nova (RK3308B), alongside a new generic uefi-arm64-dt family and board intended to standardize UEFI device-tree targets. Qualcomm enablement advanced through Radxa Dragon Q6A and Q8B work, including UFS provisioning for Kodiak, EDL-based UFS flashing in the imager, and audioreach topology firmware for sc8280xp. Catalog assets were extended for the MaaXBoard 8ULP, Mellow Fly C5, Xiaomi Sheng, and the new Radxa an…

This cycle centers on Linux 7.2/7.3 kernel enablement across out-of-tree drivers, new board support and platform fixes across Rockchip, SpacemiT, and Amlogic, and a broad documentation and CI cleanup. Kernel progression dominated the driver ecosystem, with 7.3 patch sets prepared for rockchip64, meson64, and the UEFI targets, and edge bumps to 7.2.3 landing for qcs6490, qrb2210, and sc8280xp. A wave of Wi‑Fi drivers was re-enabled and bumped for 7.3 compatibility, including rtl8189es/fs, rtl8192eu, rtl8723ds, rtl8852bs, uwe5622, and bcmdhd-dkms, most addressing the strncpy removal and the cfg80211 remain_on_channel cookie signature change. The rk35xx vendor kernel also ad…

This week's work centers on Rockchip platform maturation, kernel and toolchain modernization, and board-level enablement across vendors. Rockchip received the largest share of attention, with RK3528 gaining a thermal driver, cooling-map refinements, and cleanup of legacy PCIe and pmdomain workarounds. The Radxa E24C now stores its U-Boot environment in SPI flash and reads switch port MAC addresses from EEPROM, while device trees for the Mixtile Blade 3, Core3588E, and Edge 2 were corrected. New board support was added for the Boardcon SBC3568, and the Rock 5T now ships an edge kernel. On the configuration side, hyphenated LINUXFAMILY handling was fixed in both the kernel …

This week in Armbian development saw significant progress across board support, desktop environments, and infrastructure. Notably, NanoPC T6 LTS Plus was added as a reusable board, and support for Ubuntu 26.04 LTS ("Resolute") expanded to desktop package coverage and testing. Multiple improvements targeted desktop environments, including package updates, installation fixes, and branding enhancements for browsers. Kernel and bootloader updates were implemented for various boards, with mainline kernel bumped to 7.0 stable and u-boot upgrades for Rockchip devices. Infrastructure enhancements included new CI workflows, multi-arch unit tests, and migration to a REST API. Sever…

This week's work centers on release pipeline modernization, desktop and userland refinements, and board and kernel platform maintenance. On the release and CI side, the build matrix gained codename parameterisation with Ubuntu 26.04 "resolute" set as default, a dedicated Bianbu target, and exposed map overrides, while standard-support targets now include UEFI desktops and a plain cloud variant. The KDE fast-HDMI matrix was switched from kde-neon to kde-plasma, mesa-vpu was dropped from auto-attached extensions, and external CI now skips slots with a warning when upstream sources break. Supporting fixes route forky/loong64 base-files lookups to the main archive and add AI …

This week's development centered on kernel and toolchain progression, expanded board support, and substantial wireless driver cleanup. Mainline tracking advanced with kernel bumps to 7.2-rc7, Rockchip edge promoted to 7.2, and sunxi edge moved to 7.1.y. Platform work included loong64 migration from debian-ports to the main Debian archive with corresponding apt repository publishing, mainline kernel and U-Boot enablement on the Avaota A1, restored CONFIG_DWMAC_SUN8I for sunxi64, and a new RK3528 bl32/DDR blob update. Rockchip64 also received backported fixes for an 8250 DMA reopen crash and for CAN TX stalls. Board coverage grew across multiple vendors, with the NanoPi NEO…

This week's work advances on three fronts: kernel and bleedingedge alignment across Rockchip and Sunxi trees, board and platform enablement spanning RV1106 to SpacemiT, and CI hardening with self-hosted runner maintenance. On the kernel side, bleedingedge was bumped to 7.1-rc3, accompanied by cfg80211 API fixes and re-enablement of the rtl8189fs and rtl8852bs drivers for the new release. Both the rockchip64 and sunxi patch stacks for current and edge were rewritten, an upstream ptrace fix for CVE-2026-46333 was backported to linux-rockchip, and the odroidxu4-current kernel moved to 6.6.139. Platform enablement was broad. The Ayn Odin2 gained 7.0 kernel support, the Mekotr…

This week's work centers on a consolidated uwe5622 Wi-Fi/Bluetooth driver, CI and repository infrastructure changes, and board and toolchain enablement across multiple SoC families. The uwe5622 driver has been relocated to a dedicated repository and unified across kernel versions. Initial commits address a use-after-free in mtty_probe(), resolve 157 -Wmissing-prototypes warnings, correct dev_addr const guards for kernels 5.17–6.18 under clang, and fix sdio_pub_int_init for the newer gpiod int_ap API on GCC 14. The build system now sources the driver from this repository, adds a GitHub Actions test workflow, and refactors the associated DVFS patch and kernel configuration.…

This week's work centers on a comprehensive CI pipeline overhaul, expanded board and SoC support, and notable U-Boot and kernel modernization across Rockchip platforms. A substantial portion of the changes target CI infrastructure hardening in the new os-ci-test repository, including self-contained release handling, GHCR authentication via builtin tokens, watchdog-based auto-retry for stalled runs, proxy normalization, and sane build timeouts (60m packages, 30m/60m images). Related fixes in armbian/actions resolve datacenter runner proxy issues, while a rootfs change strips mmdebstrap's apt proxy from shipped images. Codeowners pruning of inactive maintainers and a Docker…

This week's work centers on new board and SoC enablement, a broad wireless driver and firmware overhaul, and continued kernel, boot, and installer refinements. Board support expanded on multiple fronts. A new RK3562 family was introduced alongside the KICKPI K3B with mainline U-Boot and Linux, and mainline 7.2 bring-up landed for the S5P6818 platform covering NanoPC-T3+, NanoPi M3, and Fire3. The FriendlyELEC NanoPi R28S, Wildfire Lubancat 3 v2, OrangePi CM5 Base edition, and SpacemiT Musebook (current branch) were added, while the Mixtile Edge2 and Blade 3, Orange Pi 5 Max/Ultra, and Banana Pi M2 Ultra received targeted fixes for Bluetooth, eMMC, Ethernet, and thermal be…

This week's updates center on new hardware enablement, a broad U-Boot v2026.07 modernization, and build system hardening for toolchain and infrastructure changes. Board support expanded across multiple SoC families, including the X88 PRO RK3566 TV box, Avnet MaaXBoard 8ULP (i.MX8ULP), EASY EAI Nano (RV1126), and the AYN Odin3. The Youyeetoo R1 v3 was promoted to standard support with named audio outputs, while the Radxa Dragon Q8B gained an edge kernel (7.1) target. Rockchip work included RK3588 CAN support for kernels 6.18/7.1/7.2, HDMI-RX fixes on the OrangePi 5 Ultra, and Mixtile Blade3 refinements on the 7.2 bleeding edge. A coordinated U-Boot bump to v2026.07 landed …

This week’s Armbian development saw significant enhancements across hardware support and system functionality. The Arduino UNO Q was officially added, along with new firmware and flash binaries for the QRB2210 and QCM2290 variants. HDMI CEC support was introduced for Rockchip RK3588/RK3576 SoCs, while panel compatibility expanded with updates for Raspberry Pi and Hardkernel ODROID-Vu8S. Key kernel improvements included a bump to version 7.0-rc6 and rewritten patches for Rockchip64-6.18. The release also featured workflow hardening, exclusion of unsupported boards, and fixes for USB-C OTG mode on Odroid-M2. These updates collectively strengthen Armbian’s platform stability…

This week in Armbian development saw a significant expansion of hardware support, including new board images and compatibility for devices such as the Ariaboard Photonicat 2, SpacemiT MUSE Book, NanoPC T6 Plus, and Mekotronics R58S2. Kernel patches were updated across multiple platforms, notably for Rockchip and Sunxi families, enhancing stability and performance. Several new modules were introduced in the configuration framework, including browser-based code-server, memory management, Docker log viewing, and subscription tracking. Improvements to documentation, security hardening, and code formatting were also implemented. Notable fixes addressed USB, Ethernet, and devic…

This week's development centered on kernel and toolchain progression, expanded board support, and substantial wireless driver cleanup. Mainline tracking advanced with kernel bumps to 7.2-rc7, Rockchip edge promoted to 7.2, and sunxi edge moved to 7.1.y. Platform work included loong64 migration from debian-ports to the main Debian archive with corresponding apt repository publishing, mainline kernel and U-Boot enablement on the Avaota A1, restored CONFIG_DWMAC_SUN8I for sunxi64, and a new RK3528 bl32/DDR blob update. Rockchip64 also received backported fixes for an 8250 DMA reopen crash and for CAN TX stalls. Board coverage grew across multiple vendors, with the NanoPi NEO…

This week in Armbian development saw significant enhancements across multiple areas, including expanded board support and improved hardware compatibility. Notable additions include new images and configurations for Qidi X-6, X-7, and Ariaboard Photonicat2 mainboards, as well as refined kernel patch maintenance and updates for various platforms. The build system received important fixes, such as resolving compilation errors and device tree issues, alongside improvements in Docker utilities and offline mode detection. Several refactoring efforts streamlined backend processes and enhanced user interface elements. The team also introduced automatic fallback mechanisms for Het…

This week in Armbian development saw significant progress across board support and kernel updates. New boards such as the Cainiao CNIOT Core, EByte ECB41-PGE, DG SVR 865 Tiny, and NORCO EMB-3531 received initial support, expanding hardware compatibility. Kernel patches were rewritten for the meson64 and rockchip64 platforms, aligning with version 6.18.18, while edge releases were bumped to 7.0-rc3 and rc4. Improvements included enhanced SD card and audio support for SpacemiT and Youyeetoo YY3588 boards, as well as refined configuration checks and display fixes. Several upstream patches were dropped or disabled, and the Dependabot schedule was updated for daily maintenance…

This week’s Armbian development saw a wide range of improvements and fixes across the project’s build framework, kernel support, and device compatibility. Notable changes include the transition from POSIX to Bash syntax for enhanced script reliability, expanded support for new hardware such as the Norco-EMB-3531 board, and the addition of Vulkan and improved 3D package descriptions. Several device-specific updates were made, including kernel enhancements for sm8250, mainline support for SpacemiT, and fixes for wireless and HDMI functionality on various boards. The team also introduced new features like a cache manager modal in the imager and improved marking for container…

This week’s Armbian development saw significant progress across board support, software modules, and workflow enhancements. Notable additions include new board images for ForLinx OK3506-S12, Cix-ACPI, and expanded support for Raspberry Pi 400, 500, and RPi3 series. Improvements to build targets and kernel patches were implemented, alongside fixes for overlayfs module logic and OpenMediaVault installation. The imager received updates for macOS compatibility and enhanced handling of write-protected devices. Several workflow optimizations and cleanup tasks were completed, streamlining concurrency and retry logic. Updates also targeted Debian trixie/sid for app builds and ref…

This week in Armbian development saw significant advancements across kernel, firmware, and build targets. The release of 6.18.y kernel UEFI images marks a major update, alongside expanded desktop build options including Cinnamon and KDE Neon for UEFI systems. Notable board support enhancements include the addition of custom build targets for Amlogic TV Boxes, the Raspberry Pi Zero 2W as a virtual board, and improved support for Orange Pi 3 LTS and Odroid M2 devices. Automation improvements streamline inventory rebuilds and board data management, while new features such as Armbian board auto-detection and browser enablement for Riscv64 boards enhance usability. Several bug…

This week’s Armbian development saw significant progress across multiple areas, including desktop environment enhancements, kernel updates, and expanded hardware support. Notable changes include the addition of GNOME desktop options, improvements to XFCE organization, and updates to U-Boot for several boards. The team introduced new board images and logos, refined Docker automation and documentation, and standardized numerous software modules for better maintainability. Kernel advancements featured bumps to 6.19-rc8, integration of ZFS v2.4.0, and targeted fixes for Rockchip and Odroid platforms. Community governance and build processes were also strengthened, alongside t…

This week’s Armbian development saw a wide range of updates focused on automation, hardware support, and workflow improvements. Key highlights include the introduction of automatic YAML target generation, expanded support for Hetzner ARM64 runners, and enhancements to the redirector update workflow with cache mirror support. Several board-specific fixes and feature additions were made, including improved power cycle handling for meson-sm1 devices and new binary files for RK35 series components. The team also advanced kernel support, notably enabling RDNA2 GPU compatibility and initial kernel 6.18 support for Ayn odin2. Continuous integration and build reliability received…

This week's work centers on kernel and board enablement, CI infrastructure and caching, and user-facing tooling improvements across the imager and configuration utilities. On the kernel and board front, Rockchip edge moved to 7.1 and mainline was bumped to 7.1-rc7, while the Raspberry Pi 4B legacy target was re-enabled after a brief revert of the BCM2711 kernel bumps. New board support landed for BeagleBadge and TMDS64EVM (AM64x) on the TI platform, the Anbernic RG DS RK3568 handheld as CSC, and the Youyeetoo YY3588 received a mainline DTS rework with ES8388 audio routing. Several long-standing fixes were merged, including a meson64 GPIO can_sleep regression breaking 1-Wi…

This week's work centers on expanded board and SoC support, build and repository infrastructure modernization, and refinements to user-facing tooling and documentation. On the hardware side, mainline support arrived for the Radxa Rock 2A/2F and the Toradex Verdin iMX8M Mini, while the KickPi K2B V2.2 DDR3 gained a full board definition including a new Maxio MAE0621 PHY driver. The Allwinner sun60iw2 platform saw substantial advancement on the Orange Pi 4 Pro with GPU, desktop, and hardware video decode enablement, alongside kernel configuration refinements. The Amlogic C400-plus received U-Boot repacking and Mali-T820 stabilization, the Rockchip armhf edge kernel was bump…

This week in Armbian development saw a broad range of updates spanning kernel enhancements, desktop improvements, and infrastructure refinements. Notable changes include new developer documentation for the desktop submodule, expanded GPU and multimedia support for vendor-kernel desktops, and several kernel version bumps for various platforms. The build system received fixes for filesystem resizing and improved dependency handling, while CI workflows were optimized with increased timeouts and better error handling. New hardware targets were added, including Radxa Dragon Q6A and Nio 12L, alongside updates to u-boot and kernel drivers for multiple devices. Additional improve…

This week saw significant development activity across the Armbian ecosystem, with numerous enhancements to desktop environment support, including the addition of KDE Neon, KDE Plasma, MATE, and i3-wm, as well as improved branding and menu documentation. The desktop module was refactored for greater modularity and YAML-driven configuration, alongside fixes for theming and package removal tracking. Hardware support expanded with new device trees for NanoPC-T6 LTS Plus and Gateway DK, plus initial support for Arduino UNO Q (Qualcomm QRB2210) and additional USB Ethernet drivers. The build system received updates for kernel versions and distribution releases, notably bumping U…

This week's work centers on release and CI infrastructure, board and U-Boot updates, and build framework hardening. On the release pipeline, asset manifest JSON is now emitted alongside uploads, third-party armbian-images.json sources are merged into the main download index, and dispatch chains were rewired so that build completion fans out cleanly to download-index regeneration and website sync. Ubuntu resolute (26.04) entered the daily build matrix, with corresponding prepare-host adjustments for its qemu-user packaging and a targeted blacklist for boards failing resolute plus GNOME. The new Armbian SDK images are now surfaced on the website and ship preloaded with the …

This cycle centers on expanded board and SoC support, kernel maintenance across sunxi, rockchip, and sophgo families, and infrastructure refinements to installer, extensions, and CI tooling. New platform enablement covers a broad range of vendors and architectures. Notable additions include the EmbedFire LubanCat 3 v2 and Seeed reComputer RK3576 devkits, the TQ-Systems MBa62xx/MBa67xx TI K3 boards, the Tanix TX6s (Allwinner H616), and the ZTL A568 (RK3568). The Allwinner A733 line advances with a full HDMI display pipeline (DE33/RCQ), PCIe/NVMe, and U-Boot 2026.07 integration for sun55iw3, while the Sophgo SG200x family bumps edge to 7.2, gains TPU support for the Milk-V …

This week's development centers on expanded board support and vendor kernel work, mainline kernel progression to 7.3 with CI resilience improvements, and a substantial refresh of the Armbian Imager. New hardware enablement spans multiple SoC families, including the Boardcon SBC3568 (RK3568), ELTAY RM66 (RK3566) with vendor HDMI and power-domain workarounds, the Anbernic RG Rotate on the new Unisoc UMS512 family, and the NanoPi M6 V2. The NanoPi R6S, R6C, M6/M6V2, and NanoPC T6/T6-LTS have been unified under a single image with shared aliases, reducing duplication across the FriendlyELEC RK3588 lineup. On the vendor side, an initial rk35xx-vendor-next branch based on 6.12-…

This week's changes center on expanded board and platform support, a modernized build and release pipeline anchored on Debian Trixie and ISO output, and a substantial documentation and release-process overhaul. On the hardware side, the EmbedFire LubanCat 4 (RK3588S) and Xiaomi Pad 6S Pro (sheng) join as new boards, Tanix TX6S is promoted to Supported, and Banana Pi R2 (MT7623) returns with kernel 6.18, edge 7.1, and U-Boot 2026.07. The reComputer RK3588 moves to the Panthor open-source GPU stack, NanoPCT6 U-Boot advances to v2026.07, and reComputer RK3576/RK3588 receives U-Boot fixes for SPI boot, NVMe, and rockusb. Several Rockchip and Qualcomm device trees are correcte…

This week's updates center on new board enablement, Rockchip platform refinements, and tooling and kernel maintenance. Board support expanded across multiple silicon families, with the addition of Seeed Studio reComputer RK3576/RK3588 DevKits and the Anbernic RG DS handheld image. The EasePi A2/R2 received substantial revisions to its board configurations and device trees, alongside a vendor logo transition to Linkease. SpacemiT K1 boot support was updated, and per-SoC LINUXCONFIG separation was introduced for the TQ family to better isolate kernel configurations. Rockchip received the bulk of low-level improvements. Notable changes include AUX recovery for USB-C DP Alt M…

Happy New Year from the Armbian Team! As we step into this exciting new year, we at Armbian would like to extend our warmest wishes for a Happy New Year to our amazing community! Thank you for your continued support and contributions that make Armbian what it is today. Together, we look forward to achieving great things and exploring new possibilities in Linux and open-source innovation. Armbian Updates Summary Week 1 (v25.2.0-trunk.274): What’s Changed in the Past Week Armbian continues to push the boundaries of Linux performance and hardware compatibility with its rolling release updates. The latest changes in version v25.2.0-trunk.274 bring exciting enhancements in…

Sharing latest packages, images or application deployments can be tedious and time-consuming. Mistakes are made very easily when time is not on our side. And as containerized micro-services increase, it becomes challenging to detect integration issues, which can impact release timelines and extend lead time for changes or LTC (Lead Time to Change). Armbian is a community-driven open-source operating system that solves this challenge by providing optimized Debian and Ubuntu Linux images for ARM development boards and ARM-based single board computers. This allows software teams to streamline the development process, speed up release to production, and deploy and maintain…

JetHome (Shenzhen JetHome Technology Co.) donated a build server for Armbian. The server compiles Armbian images, kernels and U-Boot packages. Thank you, JetHome. HW Specifications CPU 2 × Intel Xeon Gold 6148, 80 threads Memory 384 GB Storage 3.84 TB SSD, plus 20 TB of disk Network 2 × 1 Gbit/s, bonded Build runners 40 That is about a tenth of the fleet's capacity, running up to 3 kernel or 40 full image builds at once. The server also remembers work it has already done: Compiled code is reused. A rebuild takes under a minute instead of three.Software packages are downloaded once and shared by all 40 b…

Running Gemma 4 E2B on a Mali GPU with LiteRT-LMThis guide should work on any armbian minimal/console (trixie) system with a working Mali-g610 GPU. DO NOT USE DESKTOP Verified on: Orange Pi 5 Max (Rockchip RK3588, Arm Mali-G610 MC4), Armbian/Debian 13 (trixie), aarch64, 8 GB RAM. Status summary: Both CPU (XNNPACK) and GPU (WebGPU/Dawn → Vulkan → panvk → panthor) work on the mainline panthor kernel — numbers below. The GPU path needed one line of local patching in Mesa's panvk driver (raise maxImageDimension3D 512 → 2048 to meet the WebGPU minimums that LiteRT's Dawn library enforces; recipe in §5, rationale in §7.1). The model is multimodal (Text + Vision + Audio): the …

We're releasing Armbian Imager 2.0. We rebuilt the whole thing, the interface and the flashing engine underneath it. The part you'll notice first: your board boots already set up. Username, password, Wi-Fi, timezone, language. You tell Imager once, it writes that into the image, and the board comes up configured on first boot. No monitor, no keyboard, none of that blind first login. Set it up once. It configures itself.This is the big change in 2.0. You build a profile in settings: username and password, an SSH key, your Wi-Fi network and country code, timezone, locale, shell. Imager writes it straight into the image's filesystem while it flashes. Power on the board, it r…

I'd been putting this off for years. Every March, I'd read someone else's embedded world recap, tell myself "next year", and go back to my terminal. This year I actually went and I'm still processing everything I saw. First things first: the teamBefore I talk about any stand or chip, I need to tell you what made this trip different from anything I've done before. There were five of us from the Armbian team at the show: Igor, Werner, Meko, amazingfate, and me. Five people. Four countries. Some of us had worked together for years and never met in person. You know how it is in open-source, you collaborate through GitHub, you argue about patches on the mailing list, you revie…

Armbian's next release boots the FriendlyElec NanoPi M5 end-to-end from UFS on a mainline U-Boot, with no proprietary recovery image in the loop. It is the first RK3576 board in the catalogue to reach this state, and the integration pattern paves the way for the others. UFS, the storage class that replaced eMMC in phones, is packet-based and full-duplex with command queuing. The practical gain over an SD card shows up in random I/O, in latency under concurrent load, and in write endurance that holds up over years of deployment. FriendlyElec ships UFS on the M5 because the RK3576 has a native UFS controller, a sensible choice for any board destined for kiosks, robots, or i…

Dear Armbian Community, We are excited to announce that our new release is approaching quickly, with an estimated release date of May 25th. Our team is working actively on the final touches, focusing on stability and fine-tuning advanced features such as 3D and video acceleration. We’re utilizing the best available methods, as there are multiple options to consider. We are adjusting our build targets to include stable, rolling and application-specific builds. Stable Releases: For those who prefer a more reliable and tested environment. Rolling Releases: For the latest updates and experimental features. Applications: Optimized builds for specific applications. We will…

The Milk-V Duo S is a very cheap and small board. It runs a Sophgo SG2000 with an Arm Cortex-A53 and a RISC-V C906, 512 MB of RAM, and a physical slide switch decides which one boots. Armbian now supports both architectures. PR #10326 landed the port (175 files) as two thin board targets – milkv-duos-arm and milkv-duos-riscv – over a single shared family include, so the bootloader pins can't drift apart. PR #10510 moved the edge branch to kernel 7.1. Standing on the shoulders of othersThere are at least 2 projects the port owes a lot to: queenkjuul/milkv-duo-ubuntu (Ubuntu on a mainline kernel 7.0, RISC-V) and Fishwaldo/sophgo-sg200x-debian (Debian sid, vendor kernel 5.10…

Dear Armbian Community, At Armbian, we’re committed to providing stability without compromising on cutting-edge features. With that in mind, we deliver four point releases per year alongside our daily rolling releases, ensuring you have access to the best of both worlds. We’re gearing up to roll out new point release images featuring the latest kernel and packages by the end of May! Focus on Testing and Bug Hunting It’s time that we all shift our focus towards testing and bug hunting. Let’s prioritize closing any pending issues that require minimal effort, reserving the rest for post-June 1st. Notable Changes in the Pipeline Enabling Ubuntu Noble builds while keep …

As we approach our next point release, the focus shifts entirely towards bug fixing and stabilization. Feature development is on hold this month to ensure that core functionalities like network connectivity, video output, and booting processes are solid. We aim to resolve as many issues as possible during this period. However, we encourage users to report any recognized problems here so that they can be addressed in future updates. Target for next release We are targeting kernel v6.6 for our current builds and v6.10 for edge builds, while vendor kernels will remain at their latest versions—6.1.y for Rockchip 3588 and 5.15.y for Meson64 legacy. Video acceleration for Rock…

As we approach our next point release, the focus shifts entirely towards bug fixing and stabilization. Feature development is on hold this month to ensure that core functionalities like network connectivity, video output, and booting processes are solid. We aim to resolve as many issues as possible during this period. However, we encourage users to report any recognized problems here so that they can be addressed in future updates. Target for next release We are targeting kernel v6.6 for our current builds and v6.12 for edge builds, while vendor kernels will remain at their latest versions – 6.1.y for Rockchip 35xx and 5.15.y for Meson64 legacy. Video acceleration for Ro…

As we approach our next point release, the focus shifts entirely towards bug fixing and stabilization. Feature development is on hold this month to ensure that core functionalities like network connectivity, video output, and booting processes are solid. We aim to resolve as many issues as possible during this period. However, we encourage users to report any recognized problems here so that they can be addressed in future updates. Target for next release We are targeting kernel v6.12 for our current builds and v6.13 for edge builds, while vendor kernels will remain at their latest versions. We are releasing major upgrade on Rockchip vendor kernel. We focus on providing …

Modernizing SBC Storage: From Qualcomm EDL Flashing to SPI-to-NVMe Boots For years, single-board computer (SBC) storage followed a simple, predictable pattern: flash an image onto a microSD card or eMMC module, plug it in, and turn on the board. However, as modern embedded hardware approaches laptop-grade performance, that legacy approach is starting to break down. The latest quarter of Armbian development highlights a major shift toward modern storage pipelines. By combining Qualcomm Emergency Download (EDL) flashing in Armbian Imager 2.0 with a redesigned installation engine, Armbian is making high-performance hardware far easier to set up. Direct Qualcomm Flashing with…

When you download an Armbian image, flash it to your SD card or SSD, and boot your board, a huge amount of automation has already happened behind the scenes. That invisible engine is what you can see at https://actions.armbian.com. Think of it as the mission control center of Armbian’s infrastructure. It doesn’t look flashy, but it represents one of the most important parts of the project: the system that builds, tests, validates, and maintains Armbian for hundreds of boards, kernels, and configurations. Armbian isn’t just an operating system. It’s an automated production platform for embedded Linux.What is actions.armbian.com?actions.armbian.com is Armbian’s public autom…

A friendlier, faster, snap-free desktop install in armbian-configIf you've installed a desktop environment with armbian-config over the last few months, you may have noticed things feel different: there's a tier you can pick, the browser actually works on every arch, uninstall doesn't take half your system with it, and there's no snap pop-up surprising you on Ubuntu builds. That's not by accident — the desktop submodule has been quietly rebuilt from the ground up. Here's what landed, why we did it, and what it means for you. Pick the desktop you want — at install, and afterThree tiers, instead of one all-or-nothing install: minimal — DE + display manager + a terminal. Abo…

01Space “ESP32-C3-0.42LCD” is a small (23.5 x 18 mm) board equipped with ESP32-C3 RISC-V WiFi and Bluetooth microcontroller, a 0.42-inch display, and a Qwicc I2C connector to easily add modules such as sensors. The first time I saw it, the form factor immediately reminded me of the nRF52840-based XIAO BLE Sense board I just used to test Edge Impulse machine learning framework. Both boards should have similar use cases, but XIAO BLE Sense includes a 6-axis IMU sensor, and I had to connect an OLED display, while the ESP32-C3 board already integrates a display, and I would have had to connect an external Qwicc module with an accelerometer. ESP32-C3-0.42LCD specifications: So…

We’ve just written about an open-source hardware Allwinner V851S camera board from YuzukiHD, but he/she has made another interesting board with the YuzukiLOHCC PRO HDMI to USB 3.2 video acquisition board based on MacroSilicon MS2130 HDMI to USB chip, as well as MS9332 one-to-two active splitter, and MS8003/MS8005 microcontroller. YuzukiLOHCC PRO stands for Yuzuki Loop Out HDMI Capture Card PRO, and there are two HDMI ports, one for input and one for output, as well as a USB Type-C port to connect to the host and capture the video input. YuzukiLOHCC PRO key features and specifications: Main chip – MacroSilicon/UltraSemi MS2130 USB 3.2 Gen 1 high-definition video and audio …

“Adafruit Feather RP2040 with DVI Output Port” is another Raspberry Pi RP2040 board with an HDMI port that can output DVI video signal (no audio) to most TVs or monitors with an HDMI input port thanks to the PicoDVI project. The board builds upon the company’s Adafruit Feather RP2040 with the HDMI port adding just a few dollars. Adafruit Feather RP2040 with DVI Output Port specifications: MCU – Raspberry Pi RP2040 dual-core Arm Cortex M0+ microcontroller ~125 MHz (but it should be overclocked for DVI output) with 264 KB RAM Storage – 8MB SPI flash Video Output – 1x HDMI port for DVI output up to 320×240 or 400×240 resolution with 16-bit pixels, I2C signals to read EDID da…

Axelera M.2 AI accelerator module is said to deliver up to 214 TOPS of AI inference and up to 3200 FPS with ResNet -50 in a compact M.2 2280 form factor. Few details are available at this time, but the module is based on the company’s Metis AIPU (AI Processing Unit) using in-memory computing based on arrays of SRAM memory devices used to “store a matrix and perform matrix-vector multiplications “in-place” without intermediate movement of data”. This technology is said to “radically” increase the number of operations per computer cycle with without suffering from issues such as noise or lower accuracy. The Metis AI platform delivers 50+ TOPS per core (RISC-V-controlled dat…

Xiaomi Moaan InkPalm Plus is a 5.84-inch eReader powered by the same Rockchip RK3566 processor found in Pine64 PineNote 10.3-inch Linux eReader, and currently selling for 999 CNY, or about $150 US, on JD.com after a 100 CNY discount. The device looks more like a smartphone than an eReader with its relatively small display, but there must be demand for this type of hardware since it succeeds the earlier InkPlam 5 eReader with Allwinner B300 quad-core Cortex-A7 SoC, plus an even smaller 5.2-inch display. Inkpalm Plus specifications: SoC – Rockchip RK3566 quad-core A55 processor @ 1.8 GHz with Arm Mali-G52 EE GPU, 0.8 TOPS NPU (AI accelerator) System Memory – 2GB RAM Storage…

Morefine M9 is one of the first mini PCs I’ve seen sold with the 6W Intel Processor N100 Alder Lake-N quad-core processor and the price is not too bad with $199 asked for a barebone model on Aliexpress. The mini PC supports up to 32GB DDR4 RAM, is sold up with up to 1TB NVMe SSD, and features two 4K-capable HDMI 2.0 ports, Gigabit Ethernet, a WiFi 6 & Bluetooth 5.2 module, as well as four USB 3.2 ports. Morefine M9 specifications: SoC – Intel Processor N100 quad-core Alder Lake-N processor @ up to 3.4 GHz (Turbo) with 6MB cache, 24EU Intel HD graphics; TDP: 6W System Memory – Up to 32GB DDR4-3200MHz Storage M.2 2280 PCIe/NVMe socket fitted 128GB, 256GB, 512GB, or 1TB …

NVIDIA Jetson Orin Nano system-on-module (SoM) is an update to the Jetson Nano entry-level Edge AI and robotics module that delivers up to 40 TOPS of AI performance, meaning it’s up to 80 times faster than the original module. The new SoM features an hexa-core Arm Cortex-A78AE processor, an up to 1024-core NVIDIA Ampere architecture GPU with 32 Tensor cores, up to 8GB RAM, and the same 260-pin SO-DIMM connector found in the Jetson Orin NX modules. Two versions are offered with the following specifications: That means the Jetson Orin family has now six modules ranging from 20 TOPS to 275 TOPS. There’s no specific development kit for the Jetson Orin Nano SoM since it can be…

Sparkfun has launched a Satellite Transceiver Kit based on the Swarm M138 satellite and GNSS modem that allows low-bitrate two-way connectivity for IoT projects anywhere on earth. Remote IoT applications have benefited from LPWAN standards such as LoRaWAN and NB-IoT, but in some extreme cases coverage may still be challenging, so satellite communication may be the only practical option. It used to be really expensive, but Swarm makes this more affordable, and companies like SigFox and Semtech also have (or had?) plans to use low-earth orbit satellites for their respective LPWAN technologies. Swarm M138 kit content and specifications: Swarm M138 mini PCIe satellite modem a…

Inovato Quadra is an Arm Linux mini PC based on Allwinner H6 quad-core Cortex-A53 processor with 2GB RAM, 16GB flash, and running Armbian-built Debian 11 Bullseye 64-bit. If the device looks like a repurposed Android TV box, it is because it is based on the T95 Mini model with one HDMI 2.0 port, USB 3.0 and 2.0 ports, a microSD card slot, a Fast Ethernet port and WiFi 4 wireless connectivity. Inovato Quadra specifications: SoC – Allwinner H6 quad-core Arm Cortex-A53 processor @ up to 1.7 GHz with Arm Mali-720 MP2 GPU System Memory – 2GB RAM Storage – 16GB eMMC flash, MicroSD card slot Video & Audio Output HDMI 2.0 port up to 4Kp60 3.5mm AV port with video composite an…

SENSE is a compact multi-sensor board supporting measurement of air quality, sound, light intensity, temperature, proximity, etc… and designed by Zack Seifert, a seventeen-year-old electronics enthusiast and president of his school’s robotics team. SENSE can work with any microcontroller or processor with I2C (hardware or implemented with bit-banging), including Arduino and Raspberry Pi boards. and an extra Qwiic connector allows for additional sensors. SENSE board specifications: Storage – MicroSD card holder Sensors BME688 4-in-1 air quality sensors with pressure, humidity, temperature, and VOC measurements (also used to estimate CO2), as found in Arduino Nicla Sense M…

Raspberry Pi Smart Display Module is a CM5 carrier board compatible with the Intel Smart Display Module (SDM) specification, more specifically the SDM-L form factor (as opposed to the smaller SDM-S option). The Intel SDM standard has been around for years, and we first wrote it in 2018, covering the Axiomtek SDM300s (SDM-S) module. These cards are designed to be plugged into compatible digital signage displays, kiosks, point-of-sale systems, and so on. They feature a standard 98-pin PCIe edge connector with USB 3.0, HDMI 1.4/2.0, I2C/UART/SPI signalling, as well as Ethernet, HDMI, USB ports, and an M.2 expansion socket. Raspberry Pi Smart Display Module specifications: Co…

AMD Xilinx Kria KR260 Robotics Starter Kit features the Kria K26 Zynq UltraScale+ XCK26 FPGA MPSoC system-on-module (SoM) introduced last year together with the Kria KV260 Vision AI Starter Kit. Designed as a development platform for robotics and industrial applications, the KR260 is said to deliver nearly 5x productivity gain, up to 8x better performance per watt and 3.5x lower latency compared to Nvidia Jetson AGX Xavier or Jetson Nano kits. We’ll have a better look at the details below. Kria KR260 Robotics Starter Kit specifications: SoM – Kria K26 module with: MPSoC – Xilinx Zynq Ultrascale+ custom-built XCK26 with quad-core Arm Cortex-A53 processor up to 1.5GHz, dua…

DshanMCU Pitaya Lite is an MCU development board based on yet another STM32 alternative: MindMotion MM32 Arm Cortex-M3 microcontroller that is said to be compatible with STM32. The MCU can be clocked at up to 120 MHz, embeds 128KB SRAM, 512KB flash, and the board offers two USB Type-C ports for USB and DAP debugging, a MicroSD card slot, a few buttons, I/Os are routed via through holes as well as a mini PCIe connector that can be used to connect a display. Pitaya Lite specifications: MCU – MindMotion Microelectronics MM32F3273G8P Arm Cortex-M3 microcontroller @ 96MHz (standard) to 120MHz (max) with 128KB SRAM, 512kB Flash; LQFP100 package Storage – MicroSD card Display – …

As expected, Sipeed has now launched the Sipeed M0S IoT module based on Bouffalo Lab BL616 RISC-V microcontroller with 2.4 GHz WiFi 6, BLE 5.2, and Zigbee connectivity along with the “Sipeed M0S Dock” development board. The M0S is a tiny module (11×10 mm) with a 320 MHz wireless MCU, a ceramic antenna, and castellated holes for I/Os, and the Sipeed M0S Dock places the module on an easy-to-use board with a USB Type-C port, a BOOT button, and a 12-pin 2.54mm pitch header. Sipeed M0S module specifications: MCU – Bouffalo Lab BL616 32-bit RISC-V (RV32IMAFCP) microcontroller @ up to 320 MHz (384 MHz overclocked) with 480KB SRAM, 4MB flash, 2.4 GHz WiFi 6, Bluetooth 5.2 dual m…

Seeed Studio has introduced a new CAN Bus Grove module based on 120 MHz Gigadevice GD32E103 Arm Cortex-M4+ microcontroller with support for CAN FD at up to 5Mbps and controlled by AT command over a serial interface. The new module appears to be a drop-in replacement for the company’s $19.90 Serial CAN-BUS Grove module based on Microchip MCP2551 and MCP2515, and the main benefit of the new GD32E103 module is that it is much more cost-effective going for only $4.90 including shipping. GD32E103 CAN BUS Grove module specifications: MCU – Gigadevice GD32E103 Arm Cortex-M4F microcontroller @ up to 120 MHz with 64KB to 128KB flash, 20KB to 32KB SRAM CAN Bus – 2-pin terminal bloc…

Intel has just launched the Alder Lake-N processors and a duo of ACER Aspire 3 laptops are some of the first platforms to feature the Core i3-N305 octa-core processor, after the introduction of the MSI Cubi N ADL mini PC last week. Both models are equipped with 8GB RAM and a 256GB SSD, but the Aspire 3 A314-36P-360X comes with a 14-inch display while the Aspire 3 A315-510P-3905 features a 15.6-inch display both at Full HD (1920 x 1080) resolution. ACER Aspire 3 “Alder Lake-N” laptop specifications: SoC – Intel Core i3-N305 octa-core processor @ 1.80 GHz / 3.80 GHz (Turbo) with 32EU Intel UHD graphics @ 1.25 GHz; TDP: 15W System Memory – 8 GB LPDDR5 Storage – 256GB NVMe …

NVIDIA Jetson Orin Nano Developer Kit is an upgrade to the popular Jetson Nano Developer Kit that delivers 80 times the performance, up to 50 times the performance per watt, and gives the developers the ability to design entry-level AI-powered robots, smart drones, intelligent vision systems, and more. The Jetson Orin Nano has a similar form factor as the original Jetson Nano, but is fitted with a Jetson Orin Nano 8GB module with up to 40 TOPS AI performance, and is equipped with a DisplayPort video output, USB 3.2 Gen 2 ports, two M.2 Key M sockets for SSDs, Gigabit Ethernet, a pre-installed Wi-Fi module, and connectors for cameras. NVIDIA Jetson Orin Nano Developer Kit …

MuseLab USB-HS-Bridge is an inexpensive ($5) board based on WCH CH347 chip with a USB 2.0 Type-C interface that acts as a bridge for I2C, SPI, UART, and JTAG interfaces, as well as GPIOs. It’s notably useful to debug and download bitstreams to FPGA development boards, but it can also be used to connect various peripherals such as I2C sensors, SPI flash devices, UART devices to basically any host with a spare USB 2.0 host port. USB-HS-Bridge specifications: Chip – WCH CH347 high-speed USB to UART, I2C, SPI and JTAG chip (See link to the datasheet for details) USB – 1x USB 2.0 Type-C port with up to 480 Mbps data rate I/Os – 2x 16-pin header with 2x UART interfaces up to 9 …

Banana Pi’s BPI-PicoW-S3 is a development board following the Raspberry Pi Pico W form factor, but based on Espressif System ESP32-S3 dual-core microcontroller offering both WiFi 4 and Bluetooth LE connectivity. The Raspberry Pi SBCs have inspired many designs, but the Raspberry Pi Pico MCU boards less so. So far, I had only seen the WeAct RP2040 board with the same layout except for a USB Type-C port and a 16MB flash. But the Banana Pi BPI-PicoW-S3 provides a direct alternative to the Raspberry Pi Pico W with a more powerful microcontroller, vector instructions for AI acceleration, BLE, and about the same price at $5.5 plus shipping. Let’s see how the BPI-PicoW-S3 specif…

So far LILYGO’s ESP32 boards with an E-Paper display such as the TTGO T5 or Mini E-Paper Core featured smaller displays from 1.02-inch to 2.9-inch. But the company is now offering a larger 7.5-inch display that works with most of its T5 boards excluding the one used with a 4.7-inch display. The black and white e-paper display offers a resolution of 800 x 480 pixels, is Arduino programmable and backward compatible with earlier T5 E-paper solution, and should be one of the most cost-effective to way to make a wireless E-paper display. LilyGO 7.5-inch E-paper display specifications: Panel SKU – DKE DEPG0750_U790F3 (See PDF datasheet. note non-secure link so your browser may…

M5Stack CoreS3 is a battery-powered ESP32-S3 IoT controller with WiFi and Bluetooth connectivity, a 2-inch touchscreen display, a 0.3MP camera, a microSD card slot for storage, several sensors, plenty of I/Os, a USB Type-C OTG port, as well as a 9V to 24V DC input port. That’s the second ESP32-S3 IoT controller from M5Stack we’ve seen this year, as the CoreS3 follows the smaller M5Stack AtomS3 with a 0.85-inch display, only a few I/Os, and fewer features overall although it does come with an IR transmitter that’s missing from the larger CoreS3. M5Stack CoreS3 specifications: Wireless MCU – Espressif Systems ESP32-S3FN16R8 dual-core 32-bit Xtensa LX7 microcontroller with A…

Last year, Michael Klements made a nice-looking DIY Raspberry Pi 4 mini server with an OLED information display and a 52Pi UPS Plus module with 18650 batteries. It also included the company’s Ice Tower module for cooling, but if you wanted one you had to make your own with a 3D printer and a laser cutter. 52Pi appears to have noticed and liked the design, as they created something similar with the Raspberry Pi Mini Tower NAS kit taking one M.2 SATA SSD instead of using the UPS module. There are also a few tweaks to the mechanical design with the OLED display at an angle for easier reading. 52Pi Raspberry Pi Mini Tower NAS kit features and content: Designed for Raspberry P…

Microsoft has just introduced the Windows Dev Kit 2023, that’s basically a Windows 11 Arm mini PC powered by a Qualcomm Snapdragon 8cx Gen 3 processor designed for developers of Windows programs. Previously known as “Project Volterra”, the system comes with 32GB RAM, 512GB NVMe storage, mini DP video output, Ethernet, WiFi 6, and Bluetooth 5.1 connectivity, as well as five USB 3.2 Gen 2 ports, and more. Windows Dev Kit 2023 specifications: SoC – Qualcomm Snapdragon 8cx Gen 3 compute platform with CPU – 4x 3.0 GHz Prime cores, 4x 2.4 GHz Efficiency Cores GPU – Unnamed Adreno GPU with DirectX 12 (DX12) API support DSP – Qualcomm Hexagon Processor, Qualcomm Sensing Hub AI – …

Based on its name, the DongshanPI-PicoW board/module aims to be an Arm Linux alternative to the Raspberry Pi Pico W with a SigmaStar SSD210 dual-core Cortex-A7 processor with 64MB RAM, an SSW101B USB WiFi 4 chip, plus a good amount of I/Os thanks to four 12-pin headers. The module also comes with a 128MB SPI flash to run Linux, takes 5V power input, and offers a display interface up to 1280×800, USB 2.0, audio interfaces, and more in a small 31×31 mm form factor with 48 through and castellated holes that should be easy to integrate into compact devices. DongshanPI-PicoW specifications: SoC – SigmaStar SSD210 dual-core Arm Cortex-A7 at up to 1.0GHz with FPU, NEON, MMU, DMA…

Lolin S3 is the first ESP32-S3 board from the company, but instead of using the more compact D1 mini form factor, the board features a longer design with two rows of 20 pins offering up to 31 GPIOs. Based on ESP32-S3-WROOM-1 module, the board features 16MB QSPI flash, 8MB SPRAM, two USB Type-C OTG and UART ports, a Lolin I2C port, an RGB LED, as well as Reset and user buttons. Lolin S3 specifications: Wireless module – ESP32-S3-WROOM-1 module with: Espressif Systems ESP32-S3 dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 2.4 GHz WiFi 4 and Bluetooth 5.0 LE with support for long-range, up to 2Mbps data rate, mesh networking…

Netgear “Nighthawk” RS700 is the first WiFi 7 (802.11be) router from the company, with the tri-band router being rated “BE19000” meaning it can deliver a combined ~19Gbps link rate on all three bands. The router is based on the Broadcom BCM67263 Arm processor and with that kind of wireless bandwidth it comes with two 10GbE ports one WAN port to connect to the internet, and one LAN port to connect to the local networks plus four extra Gigabit Ethernet ports, and a USB 3.0 port for network storage. Netgear RS700 specifications: SoC – Broadcom BCM67263 quad-core WiFi 7 processor @ 2.6 GHz System Memory – 1GB RAM Storage – 512MB NAND flash for OS Networking 802.11be WiFi 7 Wi…

FriendlyElec has come up with a low-cost version of the NanoPi R6S with the NanoPi R6C router/SBC based on the same Rockchip RK3588S octa-core Cortex-A76/A55 processor but offering just one Gigabit Ethernet port and one 2.5GbE port, and adding an M.2 NVMe SSD socket for storage. The NanoPi R6C is also offered with 4GB or 8GB RAM, an optional 32GB eMMC flash soldered on the board, a Micro SD card socket, an 8K capable HDMI 2.1, USB 3.0 and USB 2.0 ports, and a few extra features we’ll discuss further below. NanoPi R6C specifications: SoC – Rockchip RK3588S octa-core processor with: CPU – 4x Cortex-A76 cores @ up to 2.4 GHz, four Cortex-A55 cores @ 1.8 GHz GPU – Arm Mali-G6…

Seeed Studio is now selling the “A203 Mini PC” industrial Linux mini PC based on an NVIDIA Jetson Xavier NX module with 8GB RAM, and a 128GB SSD loaded with JetPack 5.0.2 (Ubuntu 20.04). If the name is familiar it’s because it is based on the Leetop A203 carrier board introduced about a year ago, with HDMI, two USB 3.0 ports, RS232, and other I/Os. The mini PC also offers Gigabit Ethernet, WiFi, and Bluetooth connectivity, and is designed to operate in the -20°C to 80°C temperature range for embedded, industrial, and functional safety applications. A203 mini PC specifications: System-on-Module – NVIDIA Jetson Xavier NX with hexa-core Armv8 processor, 384-core Volta GPU, 8…

Banana Pi BPI-R2 Pro is an update to the Banana Pi BPI R2 router board that replaces MediaTek MT7623A quad-core ARM Cortex-A7 processor with a much more powerful Rockchip RK3568 quad-core Cortex-A55 processor. The Banana Pi BPI-R2 Pro board looks very similar to the first generation R2 board with the same dimensions, 2GB RAM, HDMI & DSI display interfaces, five Gigabit Ethernet ports, one SATA port, two USB 3.0 ports, and one mPCIe socket, but it also adds one M.2 socket, support for MIPI CSI cameras, and extra storage with a 16GB eMMC flash. Banana Pi BPI-R2 Pro specifications: SoC – Rockchip RK3568 quad-core Arm Cortex-A55 processor @ 2.0 GHz with Mali-G52 GPU, 0.8 …

The Banana Pi PPI-M2S is a single board computer (SBC) powered by either Amlogic A311D or S922X processor with 4GB RAM, 16GB eMMC flash, HDMI 2.1 and MIPI DSI display interfaces, one MIPI CSI camera connector, two Gigabit Ethernet ports with one PoE capable, as well as optional WiFi 5 & Bluetooth support. When we first covered the Banana Pi BPI-M2S over a year ago, all we had were some 3D renders of the board and some preliminary specifications. The company has now manufactured the board, provided some documentation, and started to take orders for the board on Aliexpress for $95.79 or $100 depending on whether Amlogic S922X or A311D is selected. Banana Pi BPI-M2S spec…

Motorola Defy Satellite Link is a Bluetooth device that can affordably bring 2-way satellite communication to any smartphone thanks to the latest 3GPP NTN (Non-Terrestrial Network) technology implemented in the MediaTek MT6825 connecting to the Bullitt Satellite Connect platform. Satellite phones and hotspot has been around for years through products such as the Iridium Go! Satellite Wi-Fi hotspot that goes for over $1,000 without a data plan, pricing that does not make it conducive to mass adoption. But silicon vendors and phone manufacturers have started to add more affordable 2-way satellite connectivity to smartphones, for example with the Snapdragon Satellite initiat…

WCH CH32V003 is a new ultra cheap RISC-V microcontroller (MCU) clocked at 48 MHz with 2KB SRAM, 16KB flash, and a bunch of interfaces that sells for under 10 cents in quantities. The MCU offers up to eighteen GPIOs, UART, SPI, I2C, an 8-channel 10-bit ADC, and several timers in TSSOP20, QFN20, SOP16, or SOP8 packages, and a small development board is also available. WCH CH32V003 specifications: CPU – 32-bit “RISC-V2A” core up to 48 MHz Memory – 2KB SRAM Storage – 16KB flash Peripherals Up to 18x GPIO with interrupt support 1x USART interface 1x I2C 1x SPI 10-bit ADC up to 8 channels 1-Wire debug interface General purpose DMA controller Timers 16-bit advanced timer 16-bit …

Last year, Jean-Luc introduced the T113-S3 processor and the small MangoPi-Dual board with T113-S3. This time, I will introduce a development board with relatively rich resources, the 100ASK-T113-PRO, which consists of a core board with T113-S3 and a carrier board with a large number of peripheral interfaces, and the upcoming Allwinner T113-S4 SoC with 256MB DDR3. 100ASK-T113-Pro Allwinner T113-S3 industrial board While the T113-S3 and D1s/F133 RISC-V processors are pin-to-pin compatible, the T113-S3 is a dual-core Arm Cortex-A7 processor with HiFi4 DSP, CAN interfaces added (CAN is not mentioned publicly, but can be seen in the T113-S3 Datasheet) and 128MB DDR3 on-chip m…

The 100ASK-V853-Pro board is a development kit consisting of an Allwinner V853 system-on-module board (SoM) and a feature-rich carrier board with a large number of interfaces. Allwinner V853 supports up to 1TOPS of NPU computing power and is mainly for AI vision application development. The core board contains a DDR and eMMC as well as a PMU chip (AXP2101) and is connected to the carrier board through a board-to-board connector. All the functional resources of the V853 are drawn out through the carrier board. The carrier board comes with 2-channels CSI camera interfaces as well as RGB and MIPI DSI display interfaces. Although 1 TOPS of AI computing power is not outstandin…

FHDM TECH DSO-500K is a 2-channel 500kS/s WiFi oscilloscope based on Raspberry Pi Pico W board that can also work over USB, and offers an analog bandwidth of up to 150kHz. We previously had seen the Raspberry Pi Pico board used as a logic analyzer, so it should come as no surprise that somebody has also come up with a Raspberry Pi Pico W-based oscilloscope that enabled visualization on Android over WiFi or USB. DSO-500K specifications and features (through the Scoppy app): MCU board – Raspberry Pi Pico W board with RP2040 dual-core Cortex-M0+ microcontroller, 2MB SPI flash, WiFi 4 and Bluetooth connectivity Sample rate – Up to 500kS/s sample rate (250kS/s with both channe…

Banana Pi has started selling an inexpensive 2.5Gbps SFP to RJ45 adapter for their Banana Pi BPI-R3 WiFi 6 router board that goes for $17.89 plus shipping ($25 shipped here) on Aliexpress. The BPI-R3 router includes five Gigabit Ethernet RJ45 ports as well as two 2.5GbE SFP cages, but since not everybody has equipment that takes SFP cables, they used to sell it with a $30 TP-Link adapter. The company now appears to have found a cheaper model marked “SFP-2.5G-T” module that works with their board. It’s designed to be inserted into one of the 2.5GbE SFP cages and provide a more common 2.5GbE RJ45 port to the user. There’s very little information about the module except its …

Sphery vs. shapes is an open-source 3D raytraced game written in C and translated into FPGA bitstream that runs 50 times more efficiently on FPGA hardware than on an AMD Ryzen processor. Verilog and VHDL languages typically used on FPGA are not well-suited to game development or other complex applications, so instead, Victor Suarez Rovere and Julian Kemmerer relied on Julian’s “PipelineC” C-like hardware description language (HDL) and Victor’s CflexHDL tool that include parser/generator and math types library in order to run the same code on PC with a standard compile, and on FPGA through a custom C to VHDL translator. More details about the game development and results a…

CNXSoft: This is a guest post by Florian Robert (1technophile) of the OpenMQTTGateway project about using a 433 MHz LoRa transceiver on an ESP32 board for home automation, specifically to talk to 433 MHz sensors Everyone is talking about Matter, Bluetooth, Zigbee, and Zwave, but before these complex communication technologies, we had one simple, robust one that our sensors and devices used to leverage: 433MHz. It may be too simplistic to talk about 433 MHz as a technology as there are different and various usages of this frequency. You can find it being used in numerous devices around your home, from your outdoor temperature sensors, and security sensors to the tire press…

ThinkCore TC-RV1126 is a USB AI camera powered by Rockchip RV1126 quad-core Cortex-A7 processor with a 2.0 TOPS NPU and equipped with a Sony Starvis IMX415 CMOS image sensor with 4K resolution (3840 x 2160). The Linux-powered camera module features a USB Type-C port compatible with UVC & UAC protocols so that it can work without drivers on Windows, Android, Linux, Mac OS, and most other operating systems with a USB stack. TC-RV1126 camera specifications: SoC – Rockchip RV1126 quad-core Arm Cortex-A7 @ 1.5 GHz + RISC-V MCU @ 400 MHz, 2D graphics engine, 2.0 TOPS NPU with support for INT8/ INT16, 14M ISP System Memory – 2x DDR3 chip (128M x 16), so that should be 512MB …

We’ve already seen compact Raspberry Pi CM4 based router boards with two Ethernet ports from DFRobots, Seeed Studio, and MCUZone. 52Pi CM4 Router Board expands on the same principle but also offers HDMI output, a 40-pin GPIO header for Raspberry Pi HAT expansion boards, and a small OLED information display. The board also includes two Gigabit Ethernet, plus the WiFi and Bluetooth connectivity from the Raspberry Pi CM4, and the extra features make the board larger (146x50mm) than competitors. But that makes the platform that much more flexibly, and can be used as a gateways for all sorts of projects thanks to the wide range of Raspberry Pi HAT available in the market. 52Pi…

5G is often associated with Gigabit speeds when found in mobile handsets or connected laptops, while there’s also 5G LPWA for battery-powered IoT devices. 5G RedCap, which stands for Reduced Capability, offers a middle ground for industrial IoT applications that keep some 5G features such as low latency, low power consumption, enhanced security, and network slicing while limiting the bandwidth to around 85 Mbps. 5G RedCap, also called NR Lite, will be part of 3GPP Release 17 scheduled for later in 2022, and further improved in Rel 18 in 2023. It will be first found in applications currently relying on LTE Cat 1 through Cat 4, and can be considered a light version of the 5…

Wireless power, no matter how inefficient it may be, sounds good and even looks good with the “5V remote wireless power supply LED pack” we feature in this post. It also feels magical with the LEDs lighting up thanks to magnetic resonance coupling technology. The solution comes with a coil as a transmitter and each LED bead also includes a small coil as a receiver. When the two are coupled, energy can be transferred from the transmitter to the receiver through the air, paper, or plastic casing, and the LEDs will light up. The magnetic field intensity in this technology is said to be similar to that of the Earth’s magnetic field, and it will not be harmful to human health …

If you are looking for an ultrawide display to show information on your PC or Raspberry Pi, there’s a 7.9-inch IPS display with 1280×400 resolution that may meet your requirements. The display is powered through a USB port and outputs video through an HDMI 1.4 input port, so it should work with any hardware equipped with HDMI input and a USB port. LR79 display specifications: Display – 7.9-inch TFT-LCD IPS display with 1280×400 resolution @ 60Hz, no touch function 178° field of view 5:16 aspect ratio Response Time: 40ms(Typ.)(Tr+Tf) Contrast Ratio: 900:1 Brightness: 500cd/㎡ Color Gamut: 70% NTSC Display Colors: 16.7M Backlight: WLED (19.2V) Connector: 30-pin ZIF Display I…

Puya Semiconductor (Shanghai) PY32 Arm Cortex-M0+ microcontroller family may be the world’s cheapest 32-bit Arm MCUs with one of the parts – PY32F002AL15S6TU – selling for under 8 cents per unit in 5K+ orders with 3KB SRAM, 20KB flash in an 8-pin SOP-8 package. Back in 2016, when I searched for the world’s cheapest MCU, I found Holtek HT48R002 8-bit microcontroller, and a few years later (2019), Padauk PMS150C “3 Cents” MCU came to my attention. However, both are 8-bit microcontrollers that come with OTG (One-Time Programming) ROM, meaning they can’t be easily used for development or updated. The Puya PY32 microcontrollers are in the same price range but offer a 32-bit A…

Firefly EC-A3588Q is a fanless 8K AI embedded computer powered by a Rockchip RK3588 processor and fitted with up to 32GB RAM, SATA or NVMe storage, offering dual Gigabit Ethernet, WiFi 6, Bluetooth 5.0, and optional 5G/4G cellular connectivity, dual 8K video outputs, etc… It is a higher-end and larger version of the Firefly EC-R3588SPC industrial mini PC based on the Rockchip RK3588S processor that adds a 4K HDMI input port, a VGA output port, gets two GbE interfaces and support for WiFi 6/Bt 5.0, offers more USB ports, and replaces some terminal blocks with DB9 interfaces for RS232, RS485, and CAN Bus interfaces. Firefly EC-Q3588Q specifications: SoC – Rockchip RK3588 oc…

Amlogic S928X multi-core Cortex-A76/A55 8K media processor, which may have been initially known as S908X, is being showcased at ICB2022 in Amsterdam in the “SEI 8K Box” developed by SEI Robotics. Amlogic S908X/S928X was first discovered in a roadmap in 2019 and was expected to launch by the end of 2020 at the time. But after a long wait of nearly three years, the Amlogic S928X processoris finally showing in SEI 8K box with an HDMI 2.1a 8K video interface, supports for HDR and advanced audio codec like Dolby Atmos and DTS, and support for Smart Home functions through an IoT module with WiFi 6E, Zigbee and more. SEI 8K box preliminary specifications: SoC – Amlogic S928X mul…

9Tripod Pico Pi V2.0 is the third Rockchip RK3588S SBC offering a powerful alternative to Raspberry Pi 4 while keeping the same form factor. It follows the Cool Pi 4 and Radxa ROCK5 Model A single board computers introduced in the last couple of months. The Pico Pi SBC, not to be confused with the Raspberry Pi Pico :), comes with 1GB to 32GB RAM, 4GB to 128GB eMMC flash, and pretty much the same port layout as the Raspberry Pi 4, except for one of the micro HDMI ports being replaced by a USB Type-C port with support for DisplayPort. 9Tripod Pico Pi V2.0 specifications: SoC – Rockchip RK3588S CPU – Octa-core processor with 4x Cortex-A76 cores @ up to 2.2-2.4 GHz, 4x Cortex…

GL.iNet are better known for their routers, but the company is also offering IoT gateways and Smart Home hubs such as the GL-S10 BLE to MQTT IoT gateway. The company is now preparing to launch the GL.iNet GL-S200 Thread Border Router in early April, and I’ve been asked to do some beta testing before launch, so GL.iNet have sent me a kit with the GL-S200 and three Thread development boards acting as IoT nodes. A Thread Border Router acts as a WiFi or/and Ethernet gateway connecting to battery-powered Thread sensor nodes equipped with a low-power 802.15.4 radio. In this first post, I’ll go through the hardware and specifications, before reporting my finding in a separate po…

Mark Himelstein, Chief Technology Officer, RISC-V International, and Dr. Philipp Tomsich, Chief Technologist & Founder, VRULL GmbH hinted that we may see a RISC-V laptop in 2022 in a presentation entitled “From Technology to Product – Maturing the RISC-V Ecosystem” with one of the slides showing what could be a RISC-V laptop prototype and The Register suspected it might come from the Institute of Software at the Chinese Academy of Sciences (ISCAS) since it was planning to build 2,000 RISC-V laptops by the end of 2022. But there’s at least one more potential RISC-V laptop project coming our way with StarFive asking users to fill out a survey about a laptop, mini PC, or…

ARES-500AI is another embedded box PC from AAEON, but instead of the usual Intel or NVIDIA Jetson accelerators, it integrates a Huawei Atlas 200 AI accelerator module based on the Ascent 310 chip delivering up to 22 TOPS of AI performance, and is designed for the Chinese market. The Linux computer supports up to 8GB RAM, SSD and MicroSD storage, and is equipped with four Gigabit Ethernet ports, some USB 3.0 ports, but somehow no video output port. Designed for industrial computer vision applications, the system supports a wide 9V to 36V power input, ARES-500AI Specifications: AI module – Huawei Atlas 200 based on Ascend 310 with 22/16/8 TOPS INT8, 11/8/4 TFLOPS FP1…

AAEON BOXER-8224AI is a thin and lightweight AI edge embedded system solution based on NVIDIA Jetson Nano system-on-module and designed for drones, or other space-constrained applications such as robotics. AAEON BOXER products are usually Embedded Box PCs with an enclosure, but the BOXER-8224AI is quite different as it’s a compact and 22mm thin board with MIPI CSI interfaces designed to add computer vision capability to unmanned areal vehicles (UAV), as well as several wafers for dual GbE, USB, and other I/Os. BOXER-8224AI specifications: AI Accelerator – NVIDIA Jetson Nano CPU – Arm Cortex-A57 quad-core processor System Memory – 4GB LPDDR4 Storage Device – 16GB eMMC 5.1 …

It’s not often we come across an Intel Xeon SBC, but that’s just what AAEON EPIC-TGH7 single board computer offers thanks to a choice of Intel Tiger Lake H processors up to the Xeon W-11865MRE octa-core/16-thread processor. So far, we had only written about Tiger Lake H-based COM Express and COM HPC modules from companies such as ADLink, Congatec, and Portwell, and the EPIC-TGH7 is the first proper SBC we’ve seen with the industrial processors. It supports up to 64GB RAM through two SO-DIMM sockets, SATA and NVME storage, offers 2.5GbE and Gigabit Ethernet ports, five video interfaces, eight USB 3.2/2.0 interfaces, and more. AAEON EPIC-TGH7 specifications: Tiger Lake-H So…