Sorry,pls https://drive.google.com/file/d/1wZulOr6_Sur_btcqqzBFTpjPmhPX0fZ1/view?usp=sharing

17 hours ago, sputnik2022 said:

Sorry,pls https://drive.google.com/file/d/1wZulOr6_Sur_btcqqzBFTpjPmhPX0fZ1/view?usp=sharing

Thanks bro...👍👍👍👍👍

Guys, i'm kind of lost here. Got the board, great stuff. But can how i use armbian with working network card and wifi? Do i have to compile something? From where? With what patches?

On 4/22/2022 at 2:38 AM, sputnik2022 said:

Sorry,pls https://drive.google.com/file/d/1wZulOr6_Sur_btcqqzBFTpjPmhPX0fZ1/view?usp=sharing

 

 

It says armbian, but also focal. So is it armbian or ubuntu?

4 minutes ago, FilSan said:

 

 

It says armbian, but also focal. So is it armbian or ubuntu?

Both.

https://docs.armbian.com/#what-is-armbian

please help me... i learned to install ipset but the result is always the same...

 

 

How to fix...please..

 

 

 

So, so,,  ARMBIAN isn't working but in command line mode?  NUTS! 

Was wanting to use it with this case.  

Getting error during --FIX-broken install.

Any documentation on this?  

I don't want to fall down the command line rabbit hole for a week or nothing.

https://www.thingiverse.com/thing:5361389

5 hours ago, Narly9999 said:

Getting error during --FIX-broken install.

What are you trying to install? Full logs.

 Nobody here has a 2nd sight.

Also take note of your support contract with Armbian: https://github.com/armbian/build#support

15 hours ago, Werner said:

What are you trying to install? Full logs.

 Nobody here has a 2nd sight.

Also take note of your support contract with Armbian: https://github.com/armbian/build#support

 

 Installing the OS. Orange Pi ZERO 2. Either distro gives errors.  

NM, I'll deal with it on my own.

 

 

If somebody is bored they could give the most recent patch series from Andre another shot: https://github.com/apritzel/linux/commits/h616-v10

On 4/22/2022 at 2:38 AM, sputnik2022 said:

Sorry,pls https://drive.google.com/file/d/1wZulOr6_Sur_btcqqzBFTpjPmhPX0fZ1/view?usp=sharing

 

 

Doesn't boot. Shows nothing on the screen. Light stays red.

1 hour ago, FilSan said:

Shows nothing on the screen.

HDMI could have troubles. Did you try serial console?

8 minutes ago, Igor said:

HDMI could have troubles. Did you try serial console?

 

I don't have serial console. It works on another monitor  tough. I just found it odd it didn't on my main one.

15 hours ago, Igor said:

HDMI could have troubles. Did you try serial console?

 

 

How can i get a serial console cable? I'm very new to this small board world

I mean, i suppose it's a kind of usb cable that connects to some of the pins?

19 minutes ago, FilSan said:

I mean, i suppose it's a kind of usb cable that connects to some of the pins?

 

Costs from 2 USD on and its a very valued tool in this world:
https://linux-sunxi.org/UART

Anyone know how to set the compile.sh script to use a newer kernel instead of the 4.9 series?

sudo ./compile.sh KERNEL_ONLY=no KERNEL_CONFIGURE=no CLEAN_LEVEL=make,debs,images,cache BUILD_MINIMAL=yes BOARD=orangepizero2 BRANCH=edge RELEASE=jammy EXPERT=yes

 

https://drive.google.com/drive/folders/1HsD11VGl-CSv98GgmWoVSlnFYEE1jMNM?usp=sharing

 

Guys, i'm running version 22.02.0-trunk.0046, from the download page. System load is always above 1. CPU temp is 53º. Is this normal? I have nothing running on it. Completely idle.  I notice these processes take the most cpu:

 

systemd-udevd

cec thread

hdmi proc

 

Is this normal?

 

EDIT: Nothing connected to the HDMI port.

I have quit on this board. Temps were reaching 70+ Cº yesterday and even 82º today! Completely iddle. The NIC stopped working. I always used a standard charger or connected it to the router via a usb cable. No idea what might have caused this. To me orange pi is just a low quality clone board. I'll get a raspberry pi when it comes available.

This load-when-idle thing is kind a persistent issue. When the first images from xulong for OPi1+ with H6 SoC were released they had the very same issue.

Later somewhen on mainline kernel it re-appeared and was gone again somewhen.

Now it is back with the H616 which is kind a small brother of the H6 chip....

On 4/29/2022 at 7:33 PM, Werner said:

This load-when-idle thing is kind a persistent issue. When the first images from xulong for OPi1+ with H6 SoC were released they had the very same issue.

Later somewhen on mainline kernel it re-appeared and was gone again somewhen.

Now it is back with the H616 which is kind a small brother of the H6 chip....

 

 

Is there any image i can download without that issue? To see if i can resuscitate it.

4 minutes ago, FilSan said:

 

 

Is there any image i can download without that issue? To see if i can resuscitate it.

I don't know. I'm not much into H616 stuff...

Good day,

 

Thanks to all participants here, some great insight’s when starting journeys with orangepizero2.

 

I choose not to download the stable Focal 5.16.y image, which could have suited my use case.

 

Essentially I’ve done two working builds of Armbian 22.05.0-trunk Bullseye with bleeding edge Linux 5.17.5-sunxi64, one which applied the reboot patch editing during the build. I had satisfied my basic criteria, and had already moved along to look into the issues of my builds more thoroughly.  For myself with the images I’ve built so far, properly functioning led’s, cpu frequency, and basic use of some pins would suffice. This venture would also deepen my understanding of here eco-system.

 

I’ve noticed as of yesterday that there is a jammy(autobuild) 5.17.5 in the download variants.

 

My question is there a specific reason the maintainer/s are not bumping the bullseye images?

 

Thanks

Hello, UART works on this board? If yes, how to activate it on the bullseye version?

Not exactly sure what you after, or what version you using, (UART) serial is enabled you don't need to activate it.

 

alistair@orangepizero2:~$ dmesg | grep ttyS
[    0.000000] Kernel command line: root=UUID=bd87b5aa-cec1-4440-a5bf-9887cc6626a8 rootwait rootfstype=ext4 console=ttyS0,115200 consoleblank=0 loglevel=1 ubootpart=98cd8c29-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
[    1.558847] printk: console [ttyS0] disabled
[    1.558931] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 32, base_baud = 1500000) is a 16550A
[    1.559090] printk: console [ttyS0] enabled
alistair@orangepizero2:~$
 

Orange Pi has released new debian images this week : https://drive.google.com/drive/folders/1Xk7b1jOMg-rftowFLExynLg0CyuQ7kCM

I haven't tested it yet but it says 5.16.17 which should be a nice step from the previous 4.9 images if they managed to make all features to work.

 

They also updated their ubuntu images https://drive.google.com/drive/folders/1ohxfoxWJ0sv8yEHbrXL1Bu2RkBhuCMup

but still with 4.9 kernel

https://github.com/orangepi-xunlong/orangepi-build

 

so wee need to wait for 3.0.0 to shwo up on git to use the device trees form 5.16.17.

 

best regards

 

 

Does it allow for the user to change the apt repositories?

 

vor 20 Stunden schrieb ilpaco:

Does it allow for the user to change the apt repositories?

 

what do you mean by chanige apt repositories ?? change the sourelists to something else ?

Does the latest Orange Pi distro allow the user to change the repositories/mirrors so that updates can be pulled from other apt repositories other than the ones included in the distro? I have found that to be a challenge in versions of Ubuntu and Debian that I have downloaded from Orange Pi's site. It seems to fail when source.list is edited to replace the repositories.