Allwinner sunxi

Working from the documentation here: https://docs.armbian.com/Developer-Guide_FEL-boot/#what-is-felnfs-boot. Not much luck so far with an FA NanoPi K1 Plus. Please see below for details. TIA.

Hello, electronics enthusiasts, I can't figure out how to activate the i2s bus and enable audio input and output, for example pcm5102(DAC) and pcm1808(ADC) My board Nano pi neo2

Hi! I was using armbian 5.60 with 4.14.70 kernel and WiFi AP worked flawsessly. Today I had to rebuild my sd card, so I downloaded the latest available build Armbian Stretch mainline kernel 4.19.y I can connect to WiFi from the board, also able to setup a WiFi AP on the board. But when I try to connect to the new AP I see the following message in terminal and the connecting device fails after several seconds: Message from syslogd@localhost at Jan 17 18:20:38 ... kernel:[ 349.842020] Internal error: Oops: 96000004 [#1] SMP Message from syslogd@localhost at Jan 17 18:20:38 ... kernel:[ 350.021242] Process RTW_CMD_THREAD (pid: 607, stack limit = 0x0000000…

Looking at the pinout table Pin 7 and PIN26, also the schematic, PWM is PA6 For this board, the overlay, is saying PWM is PA5, is it PA5? (sun50i-h5=pwm.dts) For SPI_1, CS_1 is PA10, but the table does not list a PA10, is that pin 26? (sun50i-h5-spi-add-cs1.dts)

I use a NEO2 (H5), with armbian linux 4.19.13-sunxi64, and have a StarTech usb2.0 to Gigabit-ethernet adapter, which I plug in the usb slot of the NEO2 and which gives me a new additional ethernet interface. iperf3 on this interface (against another NEO2 with its generic gigabit interface) gives maximum 111 MBit/sec, even with the tips in https://forum.armbian.com/topic/7001-slow-usb-speed-on-h5-devices-orangepi-prime-probably-cpu-governor-related/ (which actually dont change much) Using a raspberry pi (2B) with the same adapter and cable I get 170 MBit/sec, which is significantly more (although still not what one should hope for, which is up to 30…

Hello, I have Orange Pi 3 board. Panfrost drivers works fine bud I accelerated video not working. I have trouble with the drivers... I compile https://gitlab.freedesktop.org/vdpau/libvdpau and https://gitlab.freedesktop.org/vdpau/vdpauinfo When I run vdpauinfo I get: Failed to open VDPAU backend cannot open shared object file libvdpau_sun4i-drv.so No such file or directory Bud i dont know hot to make this .so file... Thank you. ==================================================================================== EDIT (i can post to here only one message per day...). Here is more informatio…

Latest kernel installed, compare attached dmesg-s. It starts working again after `reboot` invoked from serial console. dmesg-ok.log dmesg-watchdog-5.10.log

Hi all, I wanna try to use the hardware PWM on pin 7 of my orange pi one plus. Connect the fan. Toggle the SPI to enable, install wiring orangepi and all looks ok. But when in go to /sys/class/pwm i got a empty directory. I thought the should be a device pwmchip0 or something. I searched on the internet but can´t find a solution. This is what WiringOrangePi shows: Is there someone who knows what i do wrong or hwat i should do? Thank you!

My PineH64, as well as OrangePI one plus (H6) were working fine using 4.18.rc7-bionic till I have tried apt upgrade I'm getting the following error on both. Any ideas? Thank you vm Starting kernel ... [ 2.104055] Internal error: Oops: 96000004 [#1] SMP [ 2.108938] Modules linked in: [ 2.111997] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.11-sunxi64 #5.67.181221 [ 2.119819] Hardware name: Pine H64 (DT) [ 2.123750] Workqueue: events deferred_probe_work_func [ 2.128887] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.133679] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.138121] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.142560] s…

Hi, I'm here to dig into low power consumption with allwinner H6 boards, I own an OrangePi one plus and I'm already doing some tests. With an H3 board and legacy kernel I would simply tweak fex file to turn off the unnecessary, and there is already good material around this argument. But with mainline kernel there is no documentation about lowering power consumption. I would really appreciate some hints on how to tweak down consumption for H6 boards and mainline kernel, probably editing DT overlay or some other config/patch files, and re-building? I already tweaked the simplest things like: -Using fast ethernet instead of gigabit -Lowering max CPU frequency (…

Hi everyone ! I'm starting this new dedicated thread because I've got some new headache about this issue that we tried to figured out since months... I've received my PineH64 last week, and with this board I don't faced the reboot hang behaviour ! Today, since I've committed the OPi3 WIP scripts, and facing same reboot hang, I've decided to to try booting PineH64 image on this OPi3 board, but unfortunately reboot hang still occurs ... This brings me to a conclusion that it is not a software issue, but maybe hardware one ... I will dig on that during next few days by comparing PMIC and other between all those boards ... …

# uname -a Linux H6 4.18.13-sunxi64 #3 SMP Fri Oct 12 17:43:44 CST 2018 aarch64 GNU/Linux 1, burn the image to SD card 2, use nand-sata-install command, burn emmc 3, remove the SD card 4, reboot the board, can't boot, the error message: U-Boot SPL 2018.09-rc1-armbian (Oct 12 2018 - 17:39:13 +0800) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### root@H6:/mnt/emmc# fdisk -l Disk /dev/mmcblk0: 30 GiB, 32218546176 bytes, 62926848 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physic…

Hi. I would like to know if someone can help me. I was successfully able to compile armbian 6.6.30 with all of @Stephen Graf patches for my orangepi zero 3 having Full Audio working even on HDMI. see below for reference. Now I have a 2nd project. It runs the h616 with 2GB DDR3 RAM with AXP313. Can someone help me with a patch for the AXP313 on h616. Or alternatively, could my h618 orangepi zero 3 setup work if I patch it to run with DDR3? If so where can I find such a patch. Thanks in advance.

Hi! I have a Hackberry and i've tried to install Debian jessie for Cubieboard. First I have installed a legacy version; hackberry boot up correctly but my keyboard don't work so i have replaced script.bin and overwrited u-boot-sunxi-with-spl.bin with the latest version (http://dl.linux-sunxi.org/nightly/u-boot-sunxi/u-boot-sunxi/u-boot-sunxi-latest/) and it's work. Then i've try to use Vanilla version. As the same, hackberry boot up correctly but my keyboard don't work. I've tried to recompile boot.cmd with correct dtb but nothing changed. Then i've tried to create uImage from zImage (linked to vmlinuz-4.2.3-sunxi) and overwrite u-boot.bin with the latest (…

Hi, I would like to ask you guys if you have any experience in deploying a Hadoop Cluster on cubieboard2. I am using Debian jessie 4.1.4 and I am having a lot of trouble doing it. The problem is with the ports, they are not opening when I start the hadoop daemons, so my question is: Is it even possible to deploy hadoop on Debian Jessie 4.1.4? I have tried everything. Fresh install, deploy a configured hadoop cluster that was working on ubuntu 14.04 LTS, forcing the ports to open which took me to an unsolvable error( related to Protocol Buffers ), but the main problem is the ports not opening, giving the Connection Refused error. Please share your knowledge…

Hello, Is there a guide / tutorial on making Kodi run with hardware acceleration enabled on Armbian on Orange PI PC Plus? e.g. like how LibreELEC does it. I have found a bunch of information on different sites and forums, but I can't put it all together. What I know so far: * Apparently the HW-accelerated decoding is supposed to be done on Kodi's side via VDPAU API * The Kodi build in Armbian repos does not have built-in support for libvdpau (?) * ffmpeg, the video decoding library used by Kodi, doesn't support Allwinner GPU out of the box and needs patching * Kodi needs to be re-compiled with the patched ffmpeg vers…

Hi there, I would like to play hardware accelerated video with VLC on orangepi lite. Any idea how this can be done? When I tried it on RaspberryPi, it has option to select OpenmaxIL. Is this possible on Orangepi Lite, too? (I installed vlc but there is no OpenmaxIL option)

Hi all! I sadly found that I can't watch my videos. Everything's fine with youtube, nevertheless. But video I tested (h264 + avc1, m4v and avi containers) looks like fast slideshow, and sound is VERY ugly! I've tried to install mali-midgard-dkms, I've failed (see below). What should I do to watch the videos? Convert 'em all to some chosen codec? Add to sources.list kind of "unstable" thing and upgrade? Install another armbian image? Find proper mali drivers and compile it carefully? Please, help! armbianmonitor -u http://ix.io/2mXg __@opi3 ~ # apt-get install mali-midgard-dkms …

is this possible? chromium-browser --use-gl=egl [1800:1800:1212/194050:ERROR:gl_surface_egl.cc(479)] EGL display query failed with error EGL_SUCCESS[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(486)] eglInitialize Default failed with error EGL_BAD_DISPLAY[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(479)] EGL display query failed with error EGL_SUCCESS[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(486)] eglInitialize Default failed with error EGL_BAD_DISPLAY[1800:1800:1212/194050:ERROR:gl_surface_x11.cc(68)] GLSurfaceEGL::InitializeOneOff failed.[1800:1800:1212/194050:ERROR:sandbox_linux.cc(345)] InitializeSandbox() called with multiple threads in process gpu-proce…

Hello community.. I strugling with hardware acceleration on Orange PI +2E. I read all forums and used google..but all what I found are old threads. I would like to know where can I find some tutorials how to install drivers for HW encoding in h264. Compilation of ffmpeg is not a problem, I did it and tried to encode 720x576 mpeg2 live stream to h264 @ 1000kbps with fdk-aac, and it works but..all cores are around 70%, and it sometimes starting the buffering when I watching on for example on POT player or Vlc. I would like to achive two thing: 1) to be able to use hw acceleration to encode h264 from mpeg2 stream. 2) to be able to use hw de…

Hi, First of all sorry for my bad English. I am trying play video on my OrangePi Zero2+ H3 and 7inch waveshare touch screen. I couldn't get the touch screen work with Armbian 5.38 - 3.xx kernel. (I downloaded the Armbian Xenial desktop legacy kernel 3.4.y from website. In this version, mpv plays video with hardware acceleration) Then I updated to Armbian 5.44 - 4.xx kernel (I downloaded the Armbian Stretch mainline kernel 4.14.y from website.) then 7inch touch screen started to work but this time no hardware acceleration. It works "mpv vid.mp4" with dropped frames and very high CPU usage. But it gives error when I try to start video with "mpv --vo=…

Last night I downloaded "https://dl.armbian.com/orangepiplus2e/Debian_buster_next.7z" (OPi+2E) ... burned it to SD card and fired up the board ..later installed desktop and other software ...BUT when I was installing MPV I observed that few files with "Vulcan" in their names were also installed...so does that mean that mainline next 4.19.xx images for H3 are now fully suitable for multimedia desktops with Hardware graphics/Video acceleration fully supported ?

I had success with @ubobrov's sunxi-cedar-mainline driver before on H3 devices. I'm trying to get it to work on the Orange Pi 3 LTS (H6) however it keeps giving the following error: sunxi-cedar 1c0e000.video-engine: syscon failed... Any help would be much appreciated. dmesg: [ 6.167614] cedar_ve: loading out-of-tree module taints kernel. [ 6.167700] cedar_ve: module verification failed: signature and/or required key missing - tainting kernel [ 6.168445] sunxi cedar version 0.1 [ 6.168601] [cedar]: install start!!! [ 6.168654] cedar_ve: cedar-ve the get irq is 23 [ 6.168673] sunxi-cedar 1c0e000.video-engine: assign…

Is there the support for hardware interrupts on pcDuino3nano gpio2(GPIO231) or gpio3(GPIO230) in Armbian mainline, as it worked on Lubuntu ? How can it be installed/enabled ?

Hi all, I have a OrangePi Zero 2 Plus - H5 and installed Armbian buut when i build WiringOP it gives hardware line is missin message. I think so /proc/cpuinfo file is creating by armbian when bord is booting and lines contains all cpu informations. How can i fix the issue? There is any idea? Thanks in advance.

Hi all, Well i am trying to add 2 wireless board and 1 ethernet controler with out successful... The boards that i am trying are: Raspberry 2, BPI-M2 and in some weels Orange Pi Plus. The idea is add : a second ethernet 10/100/1000 to the board (enc28j60 module) one wifi card: http://www.sparklan.com/p2-products-detail.php?PKey=00b4zgTVJUGKMz3D2fh3hT0YqEY5pUo0Vq2M_xYD&WUBR-508N%20Module%20Series other wifi card: http://es.aliexpress.com/store/product/VIA-VNT9271-USB-Embedded-WLAN-Module/213061_633552912.html?storeId=213061 1. In the begining i try connect the ethernet enc28j60 module to the SPI, but in the banana sucks (http://lists.infrade...ary/2299…

Hi, how can I enable hardware decode of video h264 mpeg on H5 chip? I use a Orange pi pc2 but video goes slow and lag very much. H5 SoC has very value hardware but isn’t possibile use mali GPU yet? Thanks

Is there Hardware virtualization support available for orange Pi PC3, which have H6 family processor ? Can we port Xen hypervisor over it ?

Has anybody a good latency after the RT-PREEMPT patch? I'm using Orange Pi One (H3), Ubuntu Desktop and legacy 3.4.113 kernel patched with 30-real-time143-full-plus-rt-fixes.patch. Also I have the isolcpus=3 enabled. And latency test results for this config is master@orangepione:~/rt-tests$ sudo ./cyclictest -a -t -n -p99 # /dev/cpu_dma_latency set to 0us policy: fifo: loadavg: 2.18 2.49 1.19 1/299 3693 T: 0 ( 3034) P:99 I:1000 C: 364441 Min: 7 Act: 31 Avg: 23 Max: 3655 T: 1 ( 3035) P:99 I:1500 C: 242985 Min: 7 Act: 32 Avg: 23 Max: 3578 T: 2 ( 3036) P:99 I:2000 C: 182252 Min: 7 Act: 43 Avg: 20 Max: 2198 …

I noticed that the Cubie a5e would reboot when anything that draws moderate power (>100mA) was connected to the USB3 port. Thought it was my power supply or USB cable, but after changing that out and doing some testing, I have determined that the reboot problem doesn't happen with the Radxa Bullseye image, only with the Armbian Trixie. I haven't had a chance to test older Armbian builds to see if it broke somewhere along the way, but that's what I'll do next. Armbian boot (26.2.0 trunk 385): U-Boot SPL 2026.01_armbian-2026.01-S127a-P96c6-H560c-Va7f1-B2eb2-R448a (Feb 03 2026 - 12:13:55 +0000) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.13.0(debu…

Hello, I have a main WinTV dualHD http://www.hauppauge.de/site/products/data_dualhd.html, unt wanted this under Debian Stretch with the image from here https://www.armbian.com/cubietruck/ Mainlaine Kernel, use, according to this page https://git.linuxtv.org/media_tree.git/commit/drivers/media/usb/em28xx?id=11a2a949d05e9d2d9823f0c45fa476743d9e462b or even this https://www.mail-archive.com/ linux-media@vger.kernel.org/msg113120.html this should work ha. However, when I plug in the stick, I get this message: dmesg https://pastebin.com/mtyLnARP I also tried this here https://wiki.ubuntuusers.de/v4l-dvb/ but also without success dmesg | grep -i dvb [25.680224…

Hello, Environment : Cubieboard2 Linux 4.4.1-sunxi #10 Rootfs on 16Go SDCard Sandisk Ultra Systemctl (disabled ramlog) Hauppauge Nova-TD Stick plugged on a D-Link DUB-H4 Every time I boot my Cubieboard2, dmsg shows me: [ 6.082976] dvb-usb: found a 'Hauppauge Nova-TD Stick (52009)' in warm state. [ 6.083915] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 6.709580] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 6.712670] dvb-usb: Hauppauge Nova-TD Stick (52009) error while loading driver (-12) [ 6.712895] usbcore: registered new interface driver dvb_usb_dib0700 If I unplug and then …

Hello, can anyone share his hostapd.conf where he managed to get HT40 "width: 40 MHz" running on orange pi lite 2 while it is in AP mode ?

Hi, I am using ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i on my Nanopi neo air. uname -a says Linux nanopiair 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l armv7l armv7l GNU/Linux I think, since I made the last apt-get upgrade and rebooted, my bluetooth stopped working. lsmod gives: lsmod Module Size Used by bmp085 3487 0 pcf8591 3363 0 snd_usb_audio 80352 0 snd_hwdep 5562 1 snd_usb_audio snd_usbmidi_lib 17545 1 snd_usb_audio snd_rawmidi 17134 1 snd_usbmidi_lib gspca_ov534 9254 0 gspca_main 19688 1 gspca_ov…

Hi, I want to use my cubietruck to play the video in HD and with spdif pass-trougth and I want use mopidy. with last armbian jessie desktop : with mplayer2 : pass-trougth is ok but video is too slow with mpv : I heard a very loud noise at the output of the amplifier is not DTS decoding and is transmitted as the pcm.--> it is a kernel problem: the driver sends a sound that is not recognized by the amplifier. the SPDIF sound format is limited to 24 bits video is OK. mopidy is OK with last armbian xenial: it work because mpv is very old with mplayer2 : pass-through and video is ok but kernel panic when I put the video paused--> kernel bug solved : …

Hello I've just started struggling with Lamobo-R1 SATA problems and I'm facing the well-known bad customer service from SinoVoip. With the help of this forum I got finally the HD spinning but I've not seen anything yet related to hd-idle package. I'd like to know if anybody uses it and if the instructions on http://hd-idle.sourceforge.net/ are correct to recompile for the BPI-R1 board. As a matter of fact I'm stuck at the line saying "Run "dpkg...." Thanks! V.

Hi all, I run a BPi with Armbian 4.2 - kernel 4.2.2. A WD Red 3TB is connected via sata. I have tested hdd performance which seems to be very slow (for my opinion). Auto Mode Using Minimum Record Size 512 KB Using Maximum Record Size 8192 KB File size set to 2048000 KB Using maximum file size of 2048000 kilobytes. Command line used: iozone -a -y 512k -q 1024K -s 2000m -g 2000m -i 0 -i1 Output is in Kbytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 Kbytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. …

Dear All, I have been downloaded the Armbian Buster OS from "https://www.armbian.com/orange-pi-3/" link and flash on Orange pi3 board. We are tesing OPI3 board with TCL monitor [(Model : 55P8E) (Resolution: Ultra HD (4K) ) 55 inch ] but getting the blank screen on display. After that we changed the TCL monitor setting by HDMI 2.0 "OFF" from "Auto" mode then it's working fine. We have another monitor which does not have HDMI 2.0 OFF mode facility so we can't use our product in market due to this limitation. FYI : same thing we tested with fresh orangepi board (with default android image) and it working fine. It will be good if some…

Hi! Trying to setup HDMI audio on Banana Pi with Armbian Xenial mainline: root@bananapi:~# uname -a Linux bananapi 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l armv7l armv7l GNU/Linux I tried adding Alsa config in /etc/asound.conf root@bananapi:~$ cat /etc/asound.conf pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } root@bananapi:~$ speaker-test -twav -c2 speaker-test 1.1.0 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Playback open error: -2,No such file or directory Any suggestions?

I'm trying to get audio out work on Orange Pi Lite using HDMI. aplay -l lists sndhdmi as card #1 and I have set it up as default in ~/.asoundrc. aplay -v shows it being used, but my AV receiver doesn't recognise the Pi nor output any sound. The same cable & receiver works fine with e.g. Macbook Pro. Should the HDMI audio output work in the legacy Jessie server image for OPi Lite? If yes, how could I debug more why it doesn't seem to work?

Dear all, Recently I purchased Orange Pi Lite. I installed recommended Armbian with Legacy 3.4.113 kernel as there is no mainline image yet. When pushing the power button a logo appears, the screen goes black and after 10 seconds command prompt with login appears with no dmesg output on screen while loading kernel image and services that all is already loaded but no output shown. So far, I am happy with it, BUT when I run Vim command to open certain file, I see it opens the file and screen dimms in few seconds to complete darkness, the only way how to get out of this black screen is to switch to another console, when I switch back, it again appears a…

Hi, I am running a OrangePi One with Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l armv7l armv7l GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" And it seems that when I start the system without the hdmi cable and plug it afterwards, the HDMI is not handle correctly and my TV stays with a red screen. There is some way to configure the hdmi hot plug in this OS? I found that raspiberry pi has this option. (https://www.raspberrypi.org/documentation/configuration/config-txt/video.md)

i have orange pi pc plus and i use a hdmi monitor with it, i use xorg to run browser kiosk there is a problem with monitor if i connect hdmi before armbian starts monitor works well and show desktop but if i start orange pi (wait few seconds) and then connect hdmi cable then the monitor shows nothing

Had a bit of a success with HDMI audio and also video acceleration on OrangePi 3. What was needed was to apply some patches from LibreELEC, namely ones from projects/Allwinner/patches/linux/ . For HDMI audio to work you need 0004-sun4i-i2s-improvements.patch , which contains support for I2S on H6. When done right you should see in dmesg: asoc-simple-card sound: i2s-hifi <-> 5091000.i2s mapping ok Also what helped was an IRC chat that Jernej had with mirko some time ago: https://irclog.whitequark.org/linux-sunxi/2018-03-14 For video acceleration you need 0005-cedrus-improvements.patch and compile Cedrus driver. When done right you shou…

I had got a OrangePI One Plus (H6) on a few day ago. I had a problem with HDMI to VGA Converter that it do not work with my OrangePI One Plus. I guess it maybe about the Power of that HDMI on OrangePI One Plus was not enough for HDMI to VGA Converter's operation. Then I fix it by replace regular HDMI to VGA to be HDMI to VGA with 5V external port. And Yeah, it's work fine!!! but I had OrangePI One (H3), OrangePI PC2(H5) and OrangePI Prime(A64) too which All of them had no problem with HDMI to VGA Converter. I feel wonder with this problem on OrangePI One Plus.

Hello, installed nightly image on OPI PC 2. I get a black monitor saying "no signal" and screen is black. But it does not go into sleep mode. Dmesg output is : [ 1.273359] simple-framebuffer 7e05c000.framebuffer: framebuffer at 0x7e05c000, 0x1fa4000 bytes, mapped to 0xffff00000a000000 [ 1.273367] simple-framebuffer 7e05c000.framebuffer: format=x8r8g8b8, mode=3840x2160x32, linelength=15360 [ 1.420280] Console: switching to colour frame buffer device 480x135 [ 1.566153] simple-framebuffer 7e05c000.framebuffer: fb0: simplefb registered! AFAIK simple-framebuffer uses a framebuffer already initialized by the bootloader. So I suppose paramet…

Hello. I can't enable HDMI output for A64 on Orangepiwin platform - every time screen is blank (monitor not active). Monitor connected over hdmi to vga adapter. After linux kernel is loaded - monitor is alived. I try some options in boot.scr withnout effect for u-boot: video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0 and setenv console=tty0 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60 Need help.

I've got a fresh Orange Pi PC Plus 2 with the relevant Armbian loaded onto a new card. It seems to output just fine to HDMI on my workbench at home, using a relatively new monitor and a direct HDMI cable, but when I try other monitors I get inconsistent results. One is a Quimat 7-inch display that just shows a white backlight when connected to the OPi. However that display has issues with other boards so I'm not entirely worried about it. But the other display is a fairly modern ViewSonic monitor that exhibits a more confusing behavior. The monitor only has DVI/VGA so I'm connecting to it through a passive HDMI-DVI adapter. When I boot the board, the POST screen shows up …

Hi I was trying to setup an mini arcade to my room. I was using retrorangpi 4.2 full desktop (Debian Jessie) on my orangepipc. When it was booting, the screen is only red and the info showing in my monitor is DVI-HDMI 720p 60 but I am not using a HDMI TO DVI converter. I try to configure my display on armbian-config and I choose HDMI not DVI but the result is the same after rebooting. Can someone tell me how to fix this?

Can anyone answer here do bionic kernel supports HDMI output for Opi PC boards? Please suggest a solution as I have taken Opi PC board which has Armbian Bionic Image but no HDMI sound is coming out.

Hi Guys, I bought one of these pcDuino 4 (Nano Pi M1) boards: http://www.linksprite.com/pcduino4-nano/ Works great with Armbian Legacy Kernal. I got this screen with the HDMI + DSI Driver Board. Works fine with normal PC -> HDMI output but will not work with the Nano Pi.. https://www.alibaba.com/product-detail/LS055R1SX04-1440x2560-5-5-2K-LCD_60672828148.html?spm=a2700.7724838.2017115.1.3c93b095HGc0XS The LCD screen just turns on then off and on and off forever. It never locks on to the HDMI signal. The Nano Pi M1 works just fine with a regular monitor but not with the LCD/Driver combo. I have seen some purple images come up on …

Hi, I have the following issue: I installed Armbian 4.3 Debian (wheezy) 3.4.108 for Micro. My device is A20-Olimex-Olinuxino Micro with nand. I installed it to boot from NAND and store the rootfs on SATA /dev/sda1. When I powered it up with HDMI connected to the TV and micro sdcard plugged in, I see the red armbian logo shows up, but then display turns off and nothing. If I login with ssh I see that /boot is mounted to NAND and rootfs is indeed in /dev/sda1. If I boot without micro sdcard plugged I don't see any display output on the TV, but still the device boots up and the mounts seems the same, /boot on /dev/nand1 and /dev/sda1 is the rootfs. Perfect so I wante…

hello dear all on banana pi - i have connected all the wires but: no signal on screen what can i do now - plz advice update: found an very very interesting thread: see https://www.raspberrypi.org/forums/viewtopic.php?t=34061 presume, you have installed your selected OS on SD card. Boot sector of the SD card is normally accessible from Windows, so you can edit file config.txt. What you maybe need? Add into config.txt this line: Code: Select all hdmi_force_hotplug=1 well - this can be a good hint.. what do you say - btw. How to edit this line!? btw found some additonal texts: …

Hello, My OPi PC runs headless as a web and file server, I don-t need sound, gpu, video/hdmi, IR, microphone... only Ethernet and USB. Are these things that can be shut down to save power and perhaps memory too? How? Thanks,

I am running Ubuntu Xenial (legacy version) on my Orangepi zero 256 Mb version and using it as a web server with light torrenting. The SoC temperature reading in armbianmonitor reaches above 80 C easily. When i log in via ssh after boot the temperature reads usually 60-65 C and normal operations easily cross 70 C. This is my first SBC so I am not sure if this is normal? Can anyone tell me if these temperature readings are fine and should I do something about it?

Hi, if anybody can suggest if mentioned situation is OK? Thanks in advance. Originally all my OPI boards have been running on 624 MHz for DDR frequency. 2 days ago I decided to remove fans from My Orange Pi+ 2e and Orange Pi+ 2 (following suggestions from forum as fan is maybe not required). 1. Orange Pi+ 2e (this is running all my services which is: nextcloud, mail server, svn and web server to access mentioned) - originally with heasink and fan (as you can see downtime on Oct 14th - when I have removed fan and keep only heatsink). But something happened - with fan ddr frequency was always 624 MHz. Without fan some time after reboot it is increasi…

Hi, When I put a heavy load on my NanoPi NEO2, it locks up. The ethernet light keeps flashing, so there is still something alive? After a power reset, the NEO2 works again. I've already put a CPU fan on my CPU. CPU temp is at 25 degrees Celsius in rest, and goes up to 37 degrees Celsius under the heavy load. The heavy load is a "make -j4" of a C source code project Tips how to solve this? sander@nanopineo2:~$ while true; do date ; uptime ; cat /etc/armbianmonitor/datasources/soctemp; sleep 2; done | tee mijn-log.txt Tue Aug 22 11:46:37 UTC 2017 11:46:37 up 5:24, 2 users, load average: 0.00, 0.00, 0.00 28342 …

Hello guys, I am trying to blinking POWER_LED on my orange pi lite using google firebase but I couldn't find any resources on internet.... Here is my armbian info; http://sprunge.us/RhTM I want to develop ioT application using orange pi zero coz it has internal ethernet and wifi connection options and it is cheap. What I want to learn is: - I want to develop my ioT application using python - which version OS I should load - proper GPIO or related library for controlling GPIOs and rs-485 and i2c communications Thanks.

I installed ARMBIAN in a cubieboard2, then i insert a microSD card with 3 partitions and 1 of them cant be accesed directly from desktop... i receive the msg PERMISION DENIED. please i need help in that partition there is a program that i need to transfer to ARMBIAN to make my ARMIGA SYSTEM live again. How can i access it ?

Image of Armbian buster 4.19 Does not work on pine64 A64 2G. There is only a black TV screen. No image problem Armbian Xenial 4.75. help

So I've gone ahead and got an Orange Pi PC. I've already been using a few Raspberry Pi boards, as well as the Odroid C2. I wanted to see what the Orange looks like in comparison. It fails to boot properly. I've read a few things around the web, tried the official as well as a few of the Loboris images, including the Raspbian, Jessie and Slackware ones; used the newer script.bin and uImages, etc. But still no go. The board isn't dead, the power LED and the other 2 LEDs near the ethernet port light up. I get activity through the debug serial port, but that's about it. No image through the HDMI, no DHCP request to my router (I connected it through a wired connection…

Hi all, on orange pi zero plus with allwinner H5 I have problem to install python library pyA20 to controll gpio. On H2 it was easy to do this. Same suggestions? Thanks in advance

ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.34-sunxi, Orange Pi Zero board. Very limited Debian installed, wifi doesn't work. I found lines install xradio_wlan /bin/false install 8189es /bin/false in /etc/modprobe.d/blacklist.conf and removed it. In /etc/modules-load.d/modules.conf I added the lines 8189es xradio_wlan. No help, wi-fi didn't work, nothing about xradio or wifi in dmesg. I figured out that there was no drivers (modules) for wifi. Found this article https://linux-sunxi.org/Wifi I execute the commands from the article, section RTL8189ES / RTL8189ETV The driver has its own repository: git clone https://github.com/jwrdegoede/rtl8189ES_li…

can somebody help me create an ap using hostapd i was following this turorial https://seravo.fi/2014/create-wireless-access-point-hostapd but when i chirantan@orangepizero:~$ iw wlan0 info Interface wlan0 ifindex 4 type managed wiphy 1 i cant change the type to AP

Dear all, we need some help from Banana Pi M2 (not that important), Cubox-i/UDOO and ODROID XU4 users. Please look through this Github issue and also have look how we currently handle IRQ redistribution on various board families (example 1 and example 2) Since irqbalanced on ARM is broken (and if it would work it's often counterproductive) assigning IRQs statically to specific CPU cores increases overall system performance slightly for free. We do this for A20 boards for years (dual core --> sending Ethernet to second CPU core), extended this on H3 boards a few months ago (quad core and somewhat complicated due to the count of different boards exposing diff…

Hello people, I'm using Armbian 5.30 - kernel 3.4.113 on a Nanopi NEO. and I'm relatively new to this stuff, so please bear with me. I successfully managed to install an LCD screen on SPI (ILI9341) using this command: sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:201,led:6 speed=16000000 rotate=90 bgr=1 So far so good, but the resolution of the screen is too little and can't load anything - for example Dosbox. I would want to replicate the trick that already exists on Raspberry/Raspbian, and that is to framebuffer a higher res screen (at least 640x480) on the tiny LCD's resolution of 320x240. This is the p…

I'm developing a watchdog driver and I need get 3 gpios, from FEX file. I'm trying this: [wdt_para] wdt_used = 1 wdt_wdi_gpio = port:PH26<1><default><default><0> wdt_ign_gpio = port:PC20<0><default><default><0> wdt_off_gpio = port:PC19<1><default><default><0> if(SCRIPT_PARSER_OK != script_parser_fetch("wdt_para", "wdt_used", &wdt_used, 1)) { pr_err("%s: script_parser_fetch err. \n", __func__); return -1; } if(1 != wdt_used){ pr_err("%s: wdt_unused. \n", __func__); return -1; } …

I’m running ARMBIAN 5.38 stable on a Banana Pro and having the board go unresponsive regularly – meaning I can't login via SSH (getting a "port 22: Host is down" error) and applications stop running. I’ve used the Banana Pro board with an external 4TB harddrive via eSATA as a media/backup server with a similar software set up for several years (running regular updates). Occasionally it would go non-responsive, but I’d generally be able to run it for weeks without a restart. The need for a restart became more frequent until now it won't run for more than 12 hours without trying to log in via ssh and seeing “port 22: Host is down” and the programs like plex and …

Hi, This is my first post and I want to say thank you to all the developers and contributors of this great eco system. I've build an image for odroid xu4 with the openmediavault script. This is really great because the software packages and kernel ist up to date and running like a charm. Then I tried to get my DVB card working but that is work in progress. The card is not supported by the 4.9 Kernel and the usual way is to compile the media_build package from hier: https://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers But with an cross compiled system as armbian i…

Hello, I have got my Orange Pi PC+ reading a DS18B20, but it only gives 0.5 degree increments so I believe the resolution is set to 9 bit. This is nowhere near good enough for the application I plan to use it for. When I cat w1_slave I get: 90 01 80 01 1f ff 02 04 5c : crc=5c YES 90 01 80 01 1f ff 02 04 5c t=25000 I have attempted to use this: https://github.com/danjperron/BitBangingDS18B20 but it appears to be specifically for RaspPi. Does anyone know how I can change the resolution to 11 or 12 bit? Many thanks

Hello, i have some troubles with analog out of my Orange Pi PC. I thought i have the right cable which is assembled similar to this way: or more like this: But i almost break my device plugin it. This what have to be right channel (red) and pin 2 in the first picture, is shorted with pin 1 to GND when plugged. This confuse me a little, because the other way have to be similar to this: So before i resolder it this way, if anyone knows the correct order of jack pins, or have the right cable and can measure it, please let me know.

Hi I have problem with Cubieboard2 powering off during Legacy Armbian_5.14_Cubieboard2_Debian_jessie_3.4.112 boot. It had been explained a little bit here: http://forum.armbian.com/index.php/topic/1178-cubieboard-1-legacy-boot-failure/ So maybe I need uBoot upgrade. I had written SD card with command: dd if=Armbian_5.14_Cubieboard2_Debian_jessie_3.4.112.raw of=/dev/sdd bs=1M and upgraded uboot from here: http://phelum.net/temp/CB2/u-boot-sunxi-with-spl.bin with command: dd if=u-boot-sunxi-with-spl.bin of=/dev/sdd bs=1k seek=8 full boot output here: U-Boot SPL 2016.05-12902-g0e6e34a-dirty (Jun 19 2016 - 21:55:16) DRAM: 1024 MiB CPU: 912000000Hz, AXI/…

I have an orange Zero plus + H5 and it does not turn on anymore, I noticed that the problem is feeding it. Does anybody have his schematic to try to repair?

hy all! i need little help.... i have one orange pi plus2e and try make wireless access point... OS: armbian 5.23 Net connection: PPPOE 200/100Mbit (username/password) i read several topik about in this theme. try many settings... ap option not work my plan: I would like to do wifi access point with NAT,Firewall,DoS protection,UPnP,PortForward,IP/MAC filter function...automatic reconnection,WPA2 wifi protection i very amateure in this theme. I really prefer it if I did OpenWRT,But reading support.not available. I very big thanks help...

Good afternoon, please help configure the rotation of the logs. I am completely new to this system, unfortunately, I can not find a normal instruction on how to configure rotatilog. My problem is that the logs are full, and my necessary scripts stop working. If I constantly clear the logs manually, then the scripts work fine. I tried to configure the rotation in accordance with the instructions, it only works before the reboot, after the reboot, everything I fixed with the rotation changes the paths to /var/log.hdd/. Please help me make sure that all logs do not exceed 1m. and constantly spinning. I apologize in advance if not fully expressed his thought.

Board: Orange pi zero. wifi xr819 driver how to install and start it, step by step. please help

The latest mainline u-boot + lamobo R1 patch does not appear to work when you try dhcp or ping on a Lamobo R1 (also known as Banana Pi R1) board. I wonder if the u-boot code needs to be modified to take care of the specifics of the GMAC/switch chip on a Lamobo R1 board. The defconfig for Lamobo R1 is the same as that for Banana Pi. Please shed some light to this issue. Thanks a lot. JLu

Hi guys, does anyone know how to put a system indicator which is dock-able on the armbian panel similar to the photo below? I have tried installing "Indicator Multiload", "Multiload-ng" and "System Load Indicator" but did not have much success to make them work properly in the latest build of armbian. I am using Orange Pi PC+. Hope someone could help. Thank you very much in advance!

I am very confused. I don't know where the problem is. Have you ever encountered the same problem? Kernel 4.19.80-sunxi Debian Stretch armbian version 5.98 Orange Pi R1 No third-party hardware was added. Pure R1 bare board Start error message： [ OK ] Started LSB: set CPUFreq kernel parameters. [ 8.670214] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 8.681560] pgd = 95d3822c [ 8.684287] [00000000] *pgd=00000000 [ 8.687884] Internal error: Oops: 805 [#1] SMP THUMB2 [ 8.692942] Modules linked in: binfmt_misc 8189es zstd zram lima sun8i_codec_analog snd_soc_simple_card sun8i_adda_pr…

Hi everybody, I'm new to this forum so first let me say a big THANK YOU to the armbian team for the excellent work. I've been playing around with my orange pi pc for a while now, not really wanting to spend much time on it (family, children, work, you know the story) or dig into details, and did not find any PnP distro that was 100% satisfactory (always something missing, unstable,...), until I gave a try to armbian. Apart from a weird kernel panic at the end of every shutdown, everytying is running smoothly so far. I'm now in the process of installing OctoPrint to drive my 3D printer and I am facing a problem with python virtualenv. Basically trying to execute…

Hi All, I am trying to enable HID gadget on Banana Pi M2 Zero with latest Armbian OS for it. I followed the instructions in following link,but no luck: Switch USB port from OTG to HOST mode I get modprobe: ERROR: could not insert 'g_hid': No such device when I enter modprobe g_hid. I appreciate any help. Thanks

Hi, After upgrading linux-image-current-sunxi64 package from 21.08.1 to 22.02.1, bringing kernel version 5.15.25, the CPU temperature raised abnormaly on my olimex teres board. Temperature is above 60°C at startup, whithout any activity or load average. The issue persists with latest 5.16.16 kernel from linux-image-edge-sunxi64 package. I noticed temp at startup around 30°C with 5.4.88-sunxi64 kernel, 40°C with 5.10.60-sunxi64 kernel and above 60°C with 5.15+ kernels. Does anyone have cpu temp issue with 5.15+ kernels ?

My Orange Pi 3 LTS with Armbian 23.11.1 Jammy with Linux 6.1.63-current-sunxi64 is showing high load, but low CPU. The SBC crashed overnight. When I run htop, the following lines show state D: root lscpu root /bin/bash /usr/lib/armbian/armbian-hardware-optimization start root grep -q \<ondemand\> /sys/devices/cpu/cpu0/cpufreq/scaling_available_governors load average: 4.00, 4.00, 4.00 System load: 100% CPU usage: less than 1% sar -u 5 Linux 6.1.63-current-sunxi64 (hostname) 12/31/2023 _aarch64_ (4 CPU) 03:41:54 …

I should probably start a new thread for this but it seemed appropriate to post here at this time of nght.. So the OPi Zero Plus 2 boards arrived and I duly set up the image on a 8GB SD card, connected the serial TTL to USB adapter and booted. Everything came up fine so I set up the wifi to my local network using nmtui. Again no problems. I did an apt-get update and upgrade and rebooted, all OK again. Having SSHed into the device I get very sluggish performance and pinging from another machine on the lan I see hugely variable pings ie variations from a few ms to over a second. I installed wavemon and it shows a very strong wifi signal (as expected). The ping…

Hi all.. I can't solve one issue with nanopiair h3. I was tried to set the speed of ttyS1 using stty -F /dev/ttyS1 230400 min 0 time 5 -isig -icanon -iexten -echo -echoe -echok -echoctl -echoke -opost -onlcr that works no err messages..but my data at port is like garbage... I see this err under dmesg 21 03:10:02 2017] sw_uart_check_baudset()429 - uart1, select set 1, baud 230400, uartclk 24000000 beyond rance[30000000, 120000000] on the other hand when I check the status of uart root@FriendlyARM:/boot# cat /sys/class/tty/ttyS1/device/status uartclk = 24000000 The Uart controller register[base: 0xf1c28400]: [RTX] 0x00 = 0x00000000,…

Hi, I am running same distributed processes on my RaspberryPI Model 2B running Raspbian Jessie and two OrangePI PC's running Armbian 5.05. Though i have enough ram available i found that there is high SWAP utilization on my OrangePI PC's. Also one CPU will be always 100% in OrangePI PC's. I have swappiness = 1 for both OrangePI PC's and Raspberry PI. ulimit -l = unlimited for RaspBerryPi and ulimit -l = 64 for OrangePI PC's. Attached is the screenshot:- From left:- (1) RaspBerryPi. (2) OrangePi PC, (3) OrangePi PC. How can i limit the swap usage and high CPU for OrangePI PC? Regards, -- Avinash

Hello, I installed ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi on H3 OpiZeroPlus2 board and temperature is 60C (just after boot, nothing is running, CPU 0.5%) Is it normal? P.S. I saw overheating problem on H2+ OPi boards, but no idea if H3 also suffers from this.

After upgrading from the official version with kernel 6.1 to the CSC version with kernel 6.6 I noticed an increase in CPU temperature of as much as 10 degrees. Is this normal? Honestly, seeing 52 degrees at idle worries me a bit

Hello all, I'm working on a project where I need at least 460800 baud on a UART on the NanoPi Neo Air. Works great at lower baud rates but can't seem to get it much faster than 115200. Any thoughts on clock adjustment or CPU speed? I'm using Armbian 5.24 with the 3.X kernel

Hello, I'm new to working with Armbian and Linux in general, but I have a HiLetgo VK172 G-Mouse USB GPS/GLONASS USB GPS receiver connected to my Orange Pi PC. When I open it with MINICOM, I get a response, but it doesn't give me the coordinates: $GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30 $GPGSV,1,1,01,27,,,22*7D L,,,,,203410.00,V,N*4E $GPRMC,203411.00,V,,,,,,,031223,,,N*79 $GPVTG,,,,,,,,,N*30 $GPGGA,203411.00,,,,,0,00,99.99,,,,,,*63 ... But I want to open it for serial communication in /dev/ttyACM0. Thank you very much, and any help you can give me would be appreciated.

Hi, please find attached a file where I describe how to install a home server on a Cubietruck, and the problems I encountered. Once the problems are solved, this could be a basis for an installation instruction. Any help much appreciated! Sincerely Engelbert Installation.pdf

Hi, I have some problem about softAp mode. I am using orangepi+ and, Armbian debian jessie server 5.20version. I want to connect web page using SmartPhone. and connect other AP(Client ap mode). so i set dhcpd server. and hostapd. But, If i use "sudo iwlist wlan scan" command , kernel is rebooting with panic.. how can i set hostapd.? It's my setting. /etc/hostapd.conf ctrl_interface=/var/run/hostapd ctrl_interface_group=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_pairwise=TKIP rsn_pairwise=CCMP wpa_passphrase=12345678 driver=nl80211 wme_enabled=1 wpa_group_rekey=86400 interface=wlan0 hw_mode=g channel=6 ssid=TEST_AP /etc/network/interfaces…

Hi every body, Tanks igor for your great job with your linux versions for cubietruck. I installed jessie with kernel 3.4. I'm trying to make a media server with minidlna. Cubietruck is connected to the router with ethernet when i'm at home and minidlna stream fine. I sucessfully installed hostapd with your interfaces.hostapd file. Ethernet plugged, i can connect to wlan0 and access to minidlna. My problem is when ethernet is unplugged and i reboot the cubietruck. I cannot access to minidlna via wlan0. I set network_interface=br0 in minidlna configuration. Do i need to manually configure dhcp or something like that?

I downloaded the lastest Armbian image for my Nanopi Neo (Armbian 23.02.2 Jammy with Linxu 5.15.93-sunxi). I then connected my WiFi dongle (D-Link DWA-131) and tried to create AP using armbian-config utility. Unfortunately, the hostapd fail to start even though the status shows "active". root@armbian:/etc# systemctl status hostapd ● hostapd.service - LSB: Advanced IEEE 802.11 management daemon Loaded: loaded (/etc/init.d/hostapd; generated) Active: active (exited) since Thu 2023-03-02 12:32:58 CST; 5s ago Docs: man:systemd-sysv-generator(8) Process: 3656 ExecStart=/etc/init.d/hostapd start (code=exited, status=0/SUCCESS) CPU: 61ms Mar 02 1…

Hello, on my cubietruck, I tried to upgrade a working hostpad install with the one provided by the armbian repository. After upgrade, hostapd fails to start. Is there any particular prerequisite to using the armbian version ? Thanks in advance for your time.

Hi Sorry my english and my ignorance in linux I'm trying to activate hostapd on orange pi light. I think realtek driver. Nework appairs, but i cannot associate, it says wrong password (12345678) iwconfig has not password item: Spoiler iwconfig lo no wireless extensions. br0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"ARMBIAN" Nickname:"<WIFI@REALTEK>" Mode:Master Frequency:2.432 GHz Access Point: 2E:98:51:56:D5:65 Bit Rate:72.2 Mb/s Sensitivity:0/0 Retry:off RTS thr:off Fragment thr:off …

There is a patched version that enables noscan=1 , but the one I'm using seems like it hasn't been patched. When there is no AP's around HT40 kicks in ok without noscan=1. With noscan=1 and AP's are around hostapd won't even start in HT20 mode. Any help? root@orangepilite2:~# modinfo 88x2bu|grep version: version: v5.8.7.1_35809.20191129_COEX20191120-7777 srcversion: 43C721C4A870A632EBDE0B5 parm: rtw_chip_version:int root@orangepilite2:~# uname -a && hostapd -v Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux hostapd v2.9 User space daemon for IEEE 802.11 AP management, IEEE 802.…

Hi, In my OPi PC, the image "Armbian_5.20_Orangepipc_Debian_jessie_3.4.112" resolves .local hosts well, e.g. ` ping rpi1.local ` but the image "Armbian_5.20_Orangepipc_Debian_jessie_3.4.112_desktop" does not, it gives 'ping: unknown host rpi1.local', and it's quite odd, because an ` avahi-resolve -n rpi1.local ` works... uname -a Linux orangepipc 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:06:55 CEST 2016 armv7l GNU/Linux Any ideas? Thank you

I've been trying to learn how to do that by looking at the [leds_para] in https://linux-sunxi.org/Fex_Guide#.5Bleds_para.5D but the [leds_para] in the script.bin of my Orange Pi PC are very different: [leds_para] leds_used = 1 green_led = port:PL10<1><default><default><1> green_led_active_low = 0 red_led = port:PA15<1><default><default><0> red_led_active_low = 0 I'm lost... Can you help me? It's an Orange Pi PC with ARMBIAN 5.60 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i Thanks.

Hi, thank for your work i need to make a hotspot with cubietruck I test all debian images for cubietruck but impossible Configuration - connexion VGA - ethernet connected - microsdcard 16G sandisk ou 32 g - clavier with doogle usb all image is dowload today ** Cubietruck_Debian_3.7_jessie_4.0.3 last message Welcom to Debian GNU/Linux 8 (jessie)! [TIME] Timed ou waiting for device dev-ttyS0.device. [DEPEND] Dependency failed for serial Getty on ttyS0. ** Cubietruck_Debian_3.7_jessie_3.4.107.raw Cannot Display This video mode ** Cubietruck_Debian_3.7_wheezy_3.4.107.raw Cannot Display This video mode ** Cubietruck_Debian_3.7_wheezy_4.0.3.raw ... fai…