Allwinner sunxi

Hi, I have just received some shiny new NanoPi Neo 2 boards, hardware v 1.1, model 1711 with 1Gb RAM. I have installed Armbian Stretch mainline kernel 4.19.y with no issues at all however I have noticed that the green LED is pretty well ignoring anything I ask of it. ls -la /sys/class/leds/ total 0 drwxr-xr-x 2 root root 0 Jan 25 16:14 . drwxr-xr-x 52 root root 0 Jan 1 1970 .. lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:green:status -> ../../devices/platform/leds/leds/nanopi:green:status lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:red:pwr -> ../../devices/platform/leds/leds/nanopi:red:pwr cat /sys/class/leds/…

Hello, There seems to be scant details about the NanoPi Neo 2 LTS, so I thought I'd contribute some. My testing is much less formal than how some would measure it. What I especially like to do in the way of network speed testing are the "worst-case scenarios". My way of invoking a sort of "torture test" is to mostly test upload speeds (as they tend to be slower than download speeds), both large files (much easier), as well as uploading many tiny files (much more gruelling to store, so is therefore a major "torture test"). Having said that, I'll usually favor all-GbE networking (noting which I'm using, GbE or wifi), because I know GbE will b…

Hi there! I have been playing around with my NanoPi Neo 2 plus, I managed to get initramfs working thanks to the kernel config of armbian. I have just noticed a problem: only the first of the two USBs works. The second is completely dead. Big disclaimer: I am using an HTC PSU that provides only 1A, not the 2A that should be fed, although I do not know if this could be the cause of the issue. Aside from this problem, I cannot see other issues. Wifi is working and I disabled bluetooth. lsusb without anything plugged in to USB: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID…

I just booted the NanoPi Neo2 with the latest "Server images with Armbian Linux v6.6" running Ubuntu 24.04 (Noble). After logging in via SSH, I saw a message stating that this image is for development use only and not for production. Based on your experience, how stable is the development image? Am I correct in understanding that there is no stable image for NanoPi Neo 2 ?

(Edit: it's a red herring for me to worry about swap. Please see a few posts down...) Hello. My NanoPi Neo 2 only has 512MB RAM. I'm using it for OpenMediaVault. It starts swapping very badly (totally paralysing it) when I FTP 60GB worth of tiny files into an attached 500GB SSD SATA drive (attached with the NAS kit). Yes, ProFTPd is RAM-hungry! I know how to create and work with traditional linux swap files. I'm a noob to this whole zram thing, which I suspect is more trouble than it's worth. I would prefer to not use zram, and use a traditional swap file on an attached 6TB 3.5" SATA drive (attached over USB 2.0 with UAS). It's a backup dri…

I am building kernel 5.10.4 sources on NanoPi Neo 2 with Armbian 20.11.10 Focal and get following error: nanopineo2:~:% cd /usr/src/linux-headers-5.10.4-sunxi64 nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make headers_check nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make scripts nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make prepare scripts/Makefile.build:414: warning: overriding recipe for target 'modules.order' Makefile:1407: warning: ignoring old recipe for target 'modules.order' make[1]: *** No rule to make target 'arch/arm64/kernel/vdso/vdso.lds', needed by 'arch/arm64/kernel/vdso/vdso.so.dbg'. Stop. make: *** [arch/arm64/Makefile:182: vdso…

Just flashed Armbian 20.11.9 for NanoPi Neo 2 with kernel 5.10.4. I have run armbian-config to install kernel 5.10.4 source, but there is no any option for 5.10.x kernel sources, I see only options for 5.8.x and 5.9.x.

Hello, The NanoPi Neo 2 has an H5 SoC. When I look at the Linux mainlining effort chart at Sunxi, I see that Ethernet support for the H5 only came in the 4.15 kernel. But the kernel in the Armbian downloads for the NanoPi Neo 2 only have the 4.14.y kernel. So can one expect the GbE to work, on a NanoPi Neo 2, with the current Armbian (Bionic or Stretch)? Maybe you already backport the 4.15 Ethernet-related code (for the H5) into that 4.14.y kernel?

I have a NanoPi Neo that's been up about 4 months and I am using it for DHCP and DNS caching (using dnsmasq). This has been working fine over SSH until after the update. Previously, I could log in, edit the dnsmasq settings, and restart the service without issue. Now, when I attempt to restart a service (not just dnsmasq, I tested a couple others), it hangs and looks like it's waiting for a password entry on the TTY. (I'm logged in over SSH and I do not have a TTY connected). ... in first SSH session, this just hangs forever until I ctrl-C: root@nanopineo:/etc# systemctl restart dnsmasq ... in second SSH session, PS shows: root 1825 783 0…

Hello, I'm looking for an efficient way to update the eMMC-memory of multiple NanoPi NEO Air's (roll out a production image). I was thinking about integrating my own image in to the eflasher from FriendlyElec but then found this possibility to access the integrated memory via USB-OTG and FEL. https://forum.armbian.com/topic/1580-nanopi-neo-air/?page=9 Wherefore basically two repos are used: sunxi-tools fel-mass-storage I tried following the instructions, build and installed the sunxi-tools (sunxi-fel) and used "dd" to copy "fel-sdboot.img" to an empty SD card. For testing I took a brand new NanoPi NEO Air, connected UART0 with my P…

Hello, Is it possible to get a WiFi Direct connection from Nanopi Neo Air to for example smartphone and send a file to it? I mean with not using router. Thanks in advance for every answer!

Hi, I see in the /usr/lib/armbian/armbian-firstrun script that it runs the command: update-rc.d ap6212-bluetooth defaults for nanopi neo air (and some other boards) However if I try to run this script sudo /usr/lib/armbian/armbian-firstrun start The result is: update-rc.d: error: unable to read /etc/init.d/ap6212-bluetooth setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel versio…

Hello, as already described in this topic: https://forum.armbian.com/topic/5619-nanopi-duo-sound-delay/ I have the same problem with delayed audio. -> " if I run speaker-test -t wav, instead of the sound playing "front left" it just play the work left, the continues playing "front left" correctly." When I run an audio-output-command two times, the audio is played well with the second command. But the greater problem in my case is a loud cracking noise when audio stops. Is there anyway to prevent the shutdown of the amplifier? I have to repeatingly start and stop audio files from nodejs. Thanks for your help, Jimmy

uname -a : Linux nanopiair 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux i installed i2c-tools, libi2c-dev, python-smbus but if i try like this i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- --…

I have a NanoPi Neo Air (Allwinner H3 SoC) with onboard wifi and a serial interface. Unfortunately during some late hour hacking I managed to accidentally connect 5V onto its TX pin, I think effectively screwing up its UART0. I can no longer connect to it via a USB to TTL Serial cable. Looking at the NeoPi Nano Air's pinout diagram, it seems to have more UART devices (UART1 and UART2 even) so I wonder whether there's a way to set up armbian to communicate via these during boot? Another idea I had was to try to bypass the UART completely and to hook up the board via the wifi. Now, without having any access to a serial console, I need to …

Hi all. I install Ubuntu_xenial_default with kernel 3.4.113 and want record video from CAM500B with ov5640 image sensor. I had edited camera section in fex file with next options: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 vip_csi_pck = port:PE00<2><default><default><default> vip_csi_mck = port:PE01<2><default><default><default> vip_csi_hsync = port:PE02<2><default><default><default> vip_csi_vsync = port:PE03<2><default><default><d…

Hi, I am using Armbian for NanoPI NEO AIR + CAM500B. I am unable to see any /dev/video0. I am able to get the camera working with FA default image. Here is my dmeg output. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.112-sun8i (root@xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #14 SMP PREEMPT Wed Sep 14 20:29:31 CEST 2016 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cac…

I try to make LIRC work on NanoPi Neo Air ! A very nice board For the moment I get nothing when I run : mode2 -d /dev/lirc0 It should return pulse and space when I trigger 5V/GND on pin6 : (ref http://nanopi.io/nanopi-neo.html) cat /sys/kernel/debug/gpio GPIOs 0-383, platform/sunxi-pinctrl, sunxi-pinctrl: gpio-10 (blue_led ) out lo gpio-354 (? ) out hi gpio-362 (green_led ) out hi Does lirc pin is accessible on connector ? I guess I can check on which Gpio is it connected, but where....

I compiled full-armbian image for nanopi air. root@nanopiair:~# uname -a Linux nanopiair 4.19.25-sunxi #5.76 SMP Wed Feb 27 13:46:35 KST 2019 armv7l GNU/Linux and by armbian-config, on armbianEnv.txt overlays=spdif-out root@nanopiair:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [On-board SPDIF], device 0: spdif-dit-hifi dit-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@nanopiair:~# speaker-test -tway -c2 -Dhw:0 speaker-test 1.1.3 Playback device is hw:0 Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Rate set to 48000Hz (requested 48000H…

Hello everybody! How can I create access point with nmtui ? I spent some time playing with nmtui, and finally my nanopi got address something like 10.42.0.1. But it doesn't look normal, I can't create default gateway like 192.168.0.1 So, I couldn't see my hotspot from another device( android phone or other pc ) Maybe somebody resolved this problem?

Hi, I'm want to use my old Nanopi Neo Air with CAM500B as wifi webcam. I flashed the latest armbian bionic image, installed v4l-utils and tried to list the cameras properties with `v4l2-compliance` and `v4l2-ctl --all` but the tools always crash and I can't kill them. `dmesg` shows a NULL pointer exception: [ 56.994526] 8<--- cut here --- [ 56.997657] Unable to handle kernel NULL pointer dereference at virtual address 00000068 [ 57.005825] pgd = c774af94 [ 57.008606] [00000068] *pgd=00000000 [ 57.012243] Internal error: Oops: 5 [#1] SMP THUMB2 [ 57.017122] Modules linked in: brcmfmac brcmutil sun8i_codec_analog sun8i_adda_pr_regmap su…

Hi there, I recently purchased a NanoPi NEO Air from FriendlyElec with a CAM500B module. It works alright with the mjpg-streamer and their provided Ubuntu Core. I built an Arabian 5.27 Nano Pi Air Debian Jessie image with the default kernel and the device is no longer found. I've forced the load of ov5640 and vfe_v4l2 in /etc/modules, but /dev/video0 isn't appearing. The kernel log has this in it when the module is loaded: [ 116.519650] [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11 If I boot back to Ubuntu Core via SD, the camera is back.

All, I downloaded and built WiringNP according to the FriendlyARM instructions. Running 'gpio read all' gives me an error saying piBoardRev: Unable to determine board revision from /proc/cpuinfo for the rest the Neo Air Armbian runs fine. any ideas what's wrong?

Dear Community, I currently want to reduce the transmission power of the NanoPi Neo Air. This means that I simply want to be able to set the Wifi transmission power in 10% steps, for example. What I have already tried: Instructions according to Wiki: OpenWrt image is not flashed. No access via browser. But it doesn't matter: max. transmission power is used in AP mode. Setting as in the Wiki image "TransmitPower:auto" probably does not apply here anyway. Network Manager TUI via "sudo nmtui" has no such settings. Adjust the NVRAM files in "/lib/firmware/brcm" or "/lib/firmware/ap6212" step by step. All changes are …

Hello, I am working on a project in which we need to use a Nanopi Neo Air (based on SoC Allwinner H3). In this project we need to use the USB serial interface to communicate with another part of the project. We need to configure the Nanopi Neo Air USB interface as a peripheral USB . Nanopi Neo Air's USB serial interface is configured by default as a USB host, and in "armbian-config" there is no way to change this configuration. The USB host (which is the other part of the project) will send data to the Nanopi Neo Air whenever there is new data. Is it possible to configure the Nanopi Neo Air as a peripheral USB? How can we do this configur…

I installed the experimental version of the NanoPi Neo Air distribution on my Air a month or two ago. At the time I believe Bluetooth was not working on that version. I don't see any indication that it is not working now, but it doesn't seem to be working on my install. Is Bluetooth working on the experimental kernel? If so, should I just re-install, or is it not hard to get it working on an existing install? I just installed the latest updates and rebooted, and that didn't fix it. The symptom that I'm seeing is that if I run bluetoothctl it prints a prompt, but seems to lock up.

Hi all. I have a board nanopi neo air with armbian linux on it. We with my colleague try to setting up ffmpeg with cedrus264 for hardware accelerated capturing video from ov5640-like camera device. There is my armbianmonitor. There are my v4l2-ctl -d /dev/videox -D out: Spoiler Driver Info: Driver name : cedrus Card type : cedrus Bus info : platform:cedrus Driver version : 5.4.51 Capabilities : 0x84208000 Video Memory-to-Memory Streaming Extended Pix Format Device Capabilities Device Caps : 0x042080…

Nanopi Neo AIr Kernel Module Loading problem when dynamically loading from VirtualBox Built .Ko files.

Hi there, I'm trying to run luma.examples using an SSD1322 display via an SPI interface. I think I got the wiring right but the software is responding with errors. The app is expecting D/C and RESET parameter via a GPIO pin numbers to control the display.. I'm not sure how the Nano PI NEO Air physical pins are mapped to a GPIO port under Armbian. Where can I get a list of mappings for the physical pins to the GPIO pin numbers? How does this work? Is this an OS specific thing? Thanks in advance. PS: `uname -a` : Linux nanopiair 4.14.15-sunxi #23 SMP Sun Jan 28 12:46:39 CET 2018 armv7l GNU/Linux

Hi, First of all, thank You for your work. On a project we are using Nanopi Neo Air boards with an Allwinner h3 processor and a 8GB eMMC flashed with an Armbian OS: $ uname -a Linux <DEVICE_HOSTNAME> 6.6.75-legacy-sunxi #1 SMP Sat Feb 1 17:37:57 UTC 2025 armv7l GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye Recently we have been getting increasing reports of the boards being stuck on boot, on message 'Starting Kernel ...' (checked from logs available on COM port). Although this behavior is highly undesira…

Dear community. I like to get the NanoPi Neo air work as HID Gadget using libcomposite. I am using the dev kernel (4.10) and libcomposite is loaded. Following this tutorial http://isticktoit.net/?p=1383 the usb gadget init script is running without errors on startup. But there is no entry in /sys/class/udc/ and i get no /dev/hidg0 device Did i missed something? is there a special overlay directive for the usb controller? or is something missing in the kernel? is it better to use the g_hid module?

Hello guys, I've been trying for the past month to get USB OTG and I2C to work on a NanoPI NEO AIR running Armbian, without any success. For OTG what I've tried was adding the following to "sun8i-h3-nanopi-neo-air.dts": &usb_otg { dr_mode = "otg"; status = "okay"; }; I have also enabled OTG and I2C in the kernel config menu, but for I2C I couldn't find what to put inside the DTS file. Can someone give me pointers on how to solve this, please? Yes, I am a very inexperienced developer when it comes to embedded systems and have very poor understanding of how to properly configure a device tree source file. Any help wo…

Hello, I have downloaded and installed Armbian Buster mainline based kernel 4.19.y & Armbian Bionic mainline based kernel 4.19.y from https://www.armbian.com/nanopi-neo-air/ With both versions I have the same problem: WiFi is not working at all ! Before the installation I was running the Friendlyarm factory image and had no problems with WiFi. As I have no internet connection, I can not upload the ArmbianMonitor log. Running this gives no errors. root@nanopiair:~# armbianmonitor -v Starting package integrity check. This might take some time. Be patient please.. . It appears you don't have any corrupt files or packages! …

I am trying out the latest Armbian Debian Buster release for a Nanopi Neo Air. It is working fine. I've loaded Armbian into the eMMC and I can boot off of it. I have done `apt update && apt upgrade`. Using armbian-config, I have configured Wi-Fi and can SSH in. However, Bluetooth does not work: # systemctl status ap6212-bluetooth.service * ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Thu 2019-10-24 04:12:56 UTC; 6min ago Docs: man:systemd-sysv-generator(8) Process: 1928 ExecStart=/etc/init.d/ap6212-bluetoot…

Hi all, I am trying get wifi working on Nanopi neo air with the Mainline kernel v4.12.12. I enabled brcmfmac driver in the kernel. Downloaded the corresponding firmware(brcmfmac43430-sdio.bin) for AP6212 from : https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/plain/brcm. I have applied patch to the device tree to enable wifi (https://www.spinics.net/lists/arm-kernel/msg563666.html) I couldn't get the firmware loaded properly. Here's the log. [ 85.922929] brcmfmac: brcmf_attach Enter [ 85.922967] brcmfmac: brcmf_proto_attach Enter [ 85.922990] brcmfmac: brcmf_fweh_register event handler registered for PSM_WA…

Hi! Sorry if it is already covered but I didn't find a complete answer on the subject on the forum... So I have activated the uart3 overlay and enable CTS and RTS on an own-build Armbian 5.27 dev flavor for my NanoPi NEO Air. But I was unable to get the AP6212 Bluetooth working, I've try some infos/commands found elsewhere without any luck My question: Is Bluetooth on Nanopi NEO Air (or any H3 board with AP6212) still WIP on Armbian? Thanks. Emmanuel.

Using Armbian 5.33. What am I missing? I know the hardware is good as I've had this working before. The modules listed in /etc/modules include hci_uart which is missing. When and how is this built? It does not appear in the 3.4.113 kernel menuconfig options TAIA Jerry $ uname -a Linux nanopiair 3.4.113-sun8i #22 SMP PREEMPT Mon Sep 25 13:11:21 BST 2017 armv7l GNU/Linux # this did work! $sudo nmcli r wifi on $sudo nmcli dev wifi # lists available WAP's $sudo nmcli dev wifi connect <WAP name> password <your password here>

Hi, I'm using my NanoPi NeoAir as a bluetooth streaming sink and as a webserver for several configurations and monitoring of the device. Bluetooth works fine as long as I don't disable the powersafe mode of wifi. Even in powersafe mode the bluetooth performance is not the best. If I disable wifi at all the bluetooth performance is great. My system is: Ubuntu 16.04.3 LTS 4.11.2 iwconfig: wlan0 IEEE 802.11 ESSID:"Teebeutel" Mode:Managed Frequency:2.412 GHz Access Point: 2C:41:38:FB:D7:30 Bit Rate=54 Mb/s Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off…

First sorry for starting a similar thread here and in [1]. I try to read a DS18B20, which does not work with Armbian, DietPi, and Friendlyarm's Ubuntu. This morning, my idea was to slow down the CPU - and it worked. In detail: By running some useless cpu consuming python scripts, reading the DS18B20 works fine. As soon as i stop them, reading the sensor immediately fails. So there might be some timing issues in the implementations of w1-gpio and w1-gpio-board. Are there any hints how i can get these issues fixed? Thanks! Thomas [1] http://www.friendlyarm.com/Forum/viewtopic.php?f=47&t=393

Hi there, I've received 4 NanoPi Neo (with heatsinks as suggested by @tkaiser) recently. Here is my my first impression and also I've come across some minor issues. I hope It would be useful. I've installed Armbian_5.27.170403_Nanopineo_Ubuntu_xenial_dev_4.10.3. Also tried dietpi (kernel 3.4) and h3-mainline-ubuntu-core-qte-sd4g-beta-20170228.img (FrendlyArm, kernel 4.10) So far for good. Armbian works like a charm I have been able to install Docker and I've performed some simple tests. Awesome job guys! I've found one issue so far MAC address changes at every reboot. The issue was mentioned in some threads on the …

Hi there! I just downloaded the available image for the NanoPi Neo root@nanopineo:~# uname -a Linux nanopineo 3.4.112-sun8i #24 SMP PREEMPT Thu Aug 4 20:56:33 CEST 2016 armv7l armv7l armv7l GNU/Linux Audio output is only supported for HDMI (but there is no HDMI connector on the PCB). Analog output and SPDIF are not available in the device list. root@nanopineo:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@nanopineo:~# It is mentioned that also analog should work, but it is not listed as device as you can see above. root@nanopineo:~# d…

New toys to play The NanoPi Neo Core and Core2 are the Core-PCB without Connectors. Only Pin-holes in 2.54mm Pitch. But as the Pictures did show - there will be a Docking-Board like on the NanoPi Duo The price for the normal NanoPi Neo jumps from $7,99 to $9,99 and the new Neo Core now costs $7,99 (256MB and no eMMC) BUT has optional - also like the Neo Core2 (here 8GB default) - 8GB eMMC (512MB and 8GB eMMC = +$10 on the $7,99 Neo Core) The Neo Core2 does cost $24,99 but do have 1GB of Ram and (default) 8GB of eMMC (more options later). (long description show also - a obsolete? - option for only 512MB. But the board…

I successfully installed Armbian Focal¹ on my Neo Core 2 with MiniShield² and SSD. I find no issues after booting boot from SD-card. But I fail to boot from eMMC with System on SATA using nand-sata-install: In the serial console i see the boot process to stick after «Started udev Kernel Device Manager». Any hints how I can unblock from here? [...] U-Boot 2020.04-armbian (Sep 02 2020 - 09:50:54 +0200) Allwinner Technology CPU: Allwinner H5 (SUN50I) Model: FriendlyARM NanoPi NEO Core 2 DRAM: 512 MiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In: serial Out: serial Err: serial Net: …

Hi guys, I am trying to install `ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi64` to the internal MMC with `nand-sata-install` but it seems that the internal MMC is not available after booting from SD. I tried to set the `sdc_detmode` as described here: https://forum.armbian.com/topic/1702-orange-pi-plus-2e-where-is-16ghz-and-sd/?tab=comments#comment-13163 But there is no `script.bin`. Any idea on how to flash the internal MMC on a Neo Core 2? Cheers! Robert

Hy Just installed the Armbian Bionic image. Tried to attach different usb devices but they did not got registered. So I tried to look at the settings under Hardware in den armbian-config but it's gone.... I remember in the Armbian Stretch build it was Variable... Can someone help me Andy

Hi all, I am new to armbian, it is a wonderful project. I just have a nanopi neo core board, fellow the guide doc, it can be boot from the SD card, but the board has internal 8GB emmc. how can I install the armbian into it, so it can boot from emmc without using SD card? Thanks!

hello everyone, I managed to make a WaveShare's 3.5" SPI LCD (actually designed for arduino) work on NanoPi Neo Core running on armbian Bionic 4.19.57, but now i"m having some issues with the touchpanel (using the same SPI). i'm trying to figure out how where to connect the touchpanel cs pin, which from what i have read suppose to connect to CE1. could someone help me find out which pin is it? maybe this will help: root@nanopineo:~# dmesg | grep "spi0.1" [ 8.334791] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.335492] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.348670] ads7846_device: spidev spi0.1 1000…

Hi, Please see my comments in the other thread: Essentially when booting a Neo Core using the current air/core mainline image, the onboard fast ethernet is not being initialised. At a guess its because this is not included in the device tree (dtb/dts) for the nano pi air image or in uBoot config - however, if the image is to serve both boards it almost needs to - or they need to be separated. Both are probably reasonable options. Right now i'm trying to understand where the board defs for ethernet are collected during the image build using the armbian build environment and try and get a functional image with fast ethernet for the core…

hi everyone, I'm running latest Armbian 20.08.1 Buster with Linux 5.8.5-sunxi on a Nanopi Neo Core. I cannot understand why I cant turn GPIOA0 on\off, can't configure it as output. I have no problem with any other GPIOs, just this one. command i'm using: gpio mode 0 output gpio write 0 1 I managed to make the GPIO as Output using this command, but still no go - the output cannot be set. echo 0 > /sys/class/gpio/export echo out > '/sys/class/gpio/gpio0/direction' dmesg don't show any errors. I checked H3 documents, there's no conflict in the mux with other GPIOs, and just to be sure i turned UART every…

hi guys, i'm using legacy kernel (because im using fbtft). a couple month ago i followed a tutorial on how to install SPI touch and lcd support, now when i try to install it again - im facing issues with downloading the headers - i see the download is not available anymore. so i tried to download the current headers - using: apt install linux-headers-current-sunxi and when i try to run "make" - i face errors regarding SSL certificates and more issues. i followed the exact steps i tired in the past with a clean installation. tried ubuntu and debian (both used to work properly). what am i missing? Maybe i ne…

Good morning, I am having some problems with the i2c-1 bus, as it sometimes gets stuck even though I have external pull-up resistors. I need to be able to reset the bus to fix it and check the status of the channels, but I don’t know which Linux GPIO corresponds to the physical pins that the kernel associates with PA18 and PA19. I have tried using wiringPi, but it doesn’t indicate this. Can anyone help me? Thanks!

Good morning, I have a NanoPi Neo core where I am trying to use the usb ports (USB1, USB2 and USB3), the first thing to say is that all usbhost is active in armbian-config. The system does not recognize me anything in any of the 3, not a pendrive, or Wi-Fi or anything. If I go to armbian-config, I see that the DTB system that has loaded is that of the NanoPi air, I do not know if it can influence. USB devices receive power when connected. Any idea if I have to activate something else or modify the DTB or something? I have tried adding to armbianEnv.txt this line at the end fdtfile = sun8i-h3-nanopi-neo.dtb but nothing. Thanks and best r…

Preamble: I have done numerous hours of reading and searching (due diligence). See end. I have a FA NanoPi NEO Core-2 LTS with shield and 64G M.2 (This shield uses JMS567-LGBB1A chip USB to sata for M.2 access). I have successfully installed Armbian from SD to and booted from the eMMC. Armbian Stretch mainline kernel 4.14.y - This image https://dl.armbian.com/nanopineocore2/Debian_stretch_next.7z armbianmonitor -u results http://ix.io/1xAA Logs indicate formatting did occur correctly as far as I can tell. The volumes are formatted as I selected - along with an 'extra' ext4 volume that looks like it is just for boot. NOTE: Since…

I have board which has 2 slaves on the SPI bus, requiring ce0 and ce1. My system: Armbian 23.8.1 Bookworm with Linux 6.1.47-current-sunxi I applied overlays: spi-add-cs1 and spi-spidev, there's an spi in the system. As soon as I apply spi-double-spidev-bus.dts, the spi disappears. Скрытый текст /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&spi0>; __overlay__ { #address-cells = <1>; #size-cells = <…

board: http://nanopi.io/nanopi-neo-core.html image: Armbian Bionic mainline based kernel 4.19.38 from https://www.armbian.com/nanopi-neo/ There are two SPI separated buses with separated pins on NanoPi Core: SPI0 and SPI1 /boot/armbianEnv.txt: ... overlay-prefix=sun8i-h3 overlays=analog-codec i2c0 spi-spidev uart1 usbhost3 param_spidev_spi_bus=0 ... /dev/spidev0.0 presents How to activate a SPI1?

Dear Sirs and Madams! I am working on custom minimal image for NanoPi NEO and I've managed to solve majority of problems, however, if I observe boot process via /dev/ttyUSB0, I still get these two errors: HELLO! BOOT0 is starting! boot0 version : 4.0.0 boot0 commit : 1b3a1b587482affdd18aba923de7fe38eb7d5ee1 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V1.3 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the ch…

First up, I did have a good dig around but couldn't find anything discussing my problem but if there is a thread already existing please just link to it, no need to get huffy. I have a problem with armbian on NanoPi NEO where USB devices are not properly detected at start up (warm or cold start). Armbian version details: BOARD=nanopineo BOARD_NAME="NanoPi Neo" BOARDFAMILY=sun8i VERSION=5.67.181115 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=nightly BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage I have also tried nightly build Armbian_5.65_Nanopineo_Debian_stretch_next_4.14.78.img. The…

hello guys, tried to flash the latest debian trixie os from armbain on nanopi neo using armbian-install, but it would never boot up again. any clue?

I'm using a NanoPI NEO (v1.31 Lite, 512M RAM) which has an Allwinner H3 cpu; running Armbian Stretch from here: https://www.armbian.com/nanopi-neo/ When changing the init system from the default systemd to sysV init as described at http://without-systemd.org/wiki/index.php/How_to_remove_systemd_from_a_Debian_Stretch_installation on the next boot, the boot process freezes. Installing the package sysvinit-core conflicts with systemd-sysv, depending on which resolution I choose (install systemd-shim and some libraries, or remove systemd-sysv and NetworkManager), the boot process freezes at one of the following 3 lines: [....] Starti…

Hi all, Somebody has any problem with NanoPI NEO using g_hid as keyboard ? I'm using the code below to send the keyboard report to /dev/hidg0, but the it throws an error. https://www.kernel.org/doc/Documentation/usb/gadget_hid.txt NanoPi NEO - Linux 3.4.113-sun8i jessie [ 373.427509] g_hid gadget: adding config #1 'HID Gadget'/bf064548 [ 373.427678] g_hid gadget: adding 'hid'/c527075c to config 'HID Gadget'/bf064548 [ 373.427782] gadget_is_softwinner_otg is not -int [ 373.427837] gadget_is_softwinner_otg is not -int [ 373.427881] gadget_is_softwinner_otg is not -int [ 373.427932] gadget_is_softwinner_otg is not -int [ 373.429424] g_hid gadget: cfg 1/bf064548 s…

Hi guys, I am new here. I bought a NanoPi Neo (H3). I am new to Armbian, but not new to Debian. The NanoHat OLED works fine with UbuntuCore 16.04 and kernel 4.14. Now I installed a new microSD card with latest Armbian Bullseye. But the NanoHat doesn't work. Armbian is up-to-date: uname -a Linux nanopineo 5.15.48-sunxi #22.05.3 SMP Wed Jun 22 07:35:10 UTC 2022 armv7l GNU/Linux cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 5 (v7l) BogoMIPS : 48.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc…

The problem seems to be kernel version 6.1.30; Just writing image file 'Armbian_23.5.1_Nanopineo_bookworm_current_6.1.30_minimal.img' to SD-card gives the following output via serial console: U-Boot SPL 2022.04-armbian (May 27 2023 - 19:27:28 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.04-armbian (May 27 2023 - 19:27:28 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 33 devices, 12 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: seria…

If I open the image file for NanoPi NEO, I don't see the FAT32 boot partition. > fdisk -l Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img Medium Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img: 1,4 GiB, 1488977920 Bytes, 2908160 Sektoren Einheiten: sectors von 1 * 512 = 512 Bytes Sektorengröße (logisch/physisch): 512 Bytes / 512 Bytes I/O Größe (minimal/optimal): 512 Bytes / 512 Bytes Typ der Medienbezeichnung: dos Medienkennung: 0xbcf97591 Gerät Boot Start Ende Sektoren Größe Id Typ Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img1 8192 2908159 2899968 1,4G 83 Linux If I flash…

Dear Sirs and Madams! I am trying to reconfigure https://github.com/friendlyarm/h3_lichee BSP's kernel via make menuconfig which is producing following .config file: # # Automatically generated file; DO NOT EDIT. # Linux/arm 3.4.39 Kernel Configuration # CONFIG_ARM=y CONFIG_ARM_HAS_SG_CHAIN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_USES_GETTIMEOFFSET is not set CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_KTIME_SCALAR=y CONFIG_HAVE_PROC_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GE…

Back in March I ran into problems with the community builds for the NanoPi Neo, for Debian Bookworm. It would boot up initially, but within 30 minutes or so, it would crash. So I did a fresh install from the last official build I had saved from June 2023: Armbian_23.5.2_Nanopineo_bookworm_current_6.1.30 And then I froze these packages to keep the working firmware and kernel: armbian-firmware/bookworm,bookworm 24.2.1 all [upgradable from: 23.05.1--1-SAfece-B6ae3] linux-dtb-current-sunxi/bookworm 24.2.1 armhf [upgradable from: 23.05.1--6.1.30-Sa343-D8bc9-P73a0-C162eHfe66-HK01ba-V014b-B9c18] linux-image-current-sunxi/bookworm 24.2.1 armhf [upgra…

/sys/class/leds is not populated when running jammy with kernel 5.16.11

Using a clean install of Armbian 22.02.1 with Linux 5.15.25-sunxi on a NanoPi NEO the green & blue LEDs no longer work. Previously they have worked with both Armbian and DietPi. # uname -a Linux nanopineo 5.15.25-sunxi #22.02.1 SMP Sun Feb 27 09:23:25 UTC 2022 armv7l GNU/Linux # cat /sys/devices/platform/leds/leds/nanopi:green:status/trigger cat: '/sys/devices/platform/leds/leds/nanopi:green:status/trigger': No such file or directory # cat /sys/class/leds/led{0,1}/trigger cat: /sys/class/leds/led0/trigger: No such file or directory cat: /sys/class/leds/led1/trigger: No such file or directory # ls -lha /sys/class/leds/ total 0 drwxr-x…

hello guys, sorry i had to tag orangepione, only because i could not find nanopi neo in allwinner h3 category. anw, my question is where can i find the older releases of the armbian os, i visited archive but i could not find the image i downloaded like one year earlier which is armbian v25.11 linux kernel 6.12.51 sunxi, there used to be a legacy option in the page related to nanopi neo where i could find all the older releases but looks like it is gone.

Hi guys. I am testing a NanoPi Neo for an IoT project. I ordered one with unsoldered ethernet and USB ports. I am trying to use a miniature WiFi adapter plugged in the OTG port while powering the board from either the debug +/- pins, or from the 5V bus on the GPIO. The problem is that no mater what option I choose, the board powers up just fine, I can login using the debug port serial-over-consolem however the WiFi adapter doesn't pop up in the lsusb list. Using an OTG USB hub with external power, fires up the WiFi, however this is the only working way and my project has to have minimum cable clutter. I need to be able to plug in the NanoPi Neo on a PCB using its GPIO …

Tried installing Armbian_23.11.1_Nanopineoplus2_jammy_current_6.1.63.img and it is super slow during first boot process regardless of SD type. Localization craps out with "Failed to set time zone: Transport endpoint is not connected". I boot with wired Ethernet and when I get to a prompt I can ping outside locations. apt update produces "Hash Sum mismatch" Anyways, doing my part testing legacy boards, hahahaha

FriendlyARM has recently launched a new board in its NEO family: NanoPi NEO Plus2 As of Armbian_5.32.170704_Nanopineo2_Ubuntu_xenial_dev_4.11.8.img, few things aren't working: out of 1GB RAM, only 512MB is visible the USB socket closer to the edge (USBN1) is not visible, even with overlays Wifi and Bluetooth are not visible (AP6212A) (it's not a complaint, but just a statement

Hello, I have a NanoPi Neo Plus 2 I used to run Ubuntu Core on it but i wanted to switch out as i had less storage space available 4.7gb out of 8 and other issues as it was also out of date. I installed Armbian first on SD then on eMMC but the problem i am facing is that only 479mb of ram is available. Now in the first post on this board by Stanislav Sinyagin on July 18, 2017 it was stated that only 512 mb of ram was available but later on i saw posts of people with the whole 1Gb of ram being used. Due to the limited ram i get compilation problems among other things i am using this board headless as a server. i flashed all versions for download multiple times along with t…

Hello. Has anybody tried to encode h264 on h5 via ffmpeg cedrus264? any help would be appropriated. thanks in advnace.

Hello, I am trying to use my NanoPi neo Plus 2 rev 1.2 board as KVM with help of (kvmd-armbian) and USB-HDMI capture card and USB-A to USB-A cable as OTG for emulation of Keyboard and mouse as HID. I discoverred that If I install "Armbian 23.02 Jammy with Kernel 5.15.y" like the install script from srepac/kvmd-armbian recommends, updated it and installed the srepac/kvmd-armbian piKVM, it installed properly and it is working BUT to my OTG USB HID connection to work I had to convert sun50i-h5-nanopi-neo-plus2.dtb to sun50i-h5-nanopi-neo-plus2.dts and in there find "dr_mode" and change it to peripheral (or otg) to get my HID OTG input to work w…

Recently I wanted to give another try to a NanoPi NEO Plus2 but I noticed that it is marked as not supported and there is no Armbian Bionic image for it (the links in https://www.armbian.com/nanopi-neo-plus2/ return 404). So I checked about other FriendlyElec H5 boards: https://www.armbian.com/download/?tx_soc=h5&tx_maker=friendlyelec (I had to edit the URL as otherwise one cannot add multiple filters) And I picked the K1 plus as a close relative; the Bionic image seems working without any issue, I will keep testing and report back. The only minor issue that I could find so far is that htop will show 0 Mhz for all cores. I have report…

Sorry for the minimal info provided in this report but, due to the possible data corruption which the bug may cause, I'm not willing to reproduce this again on my board which runs in production. One week ago, I experienced data corruption happening on the nanopi. Actually it was some time (more than one month) that I saw the board acting weird: - long ssh transfers would sometime brake (via https://github.com/dooblem/bsync) - `apt update` reported invalid keys for the official armbian repository - on rare occasions, the board would freeze (not respond to ssh, requiring manual power cycle) After experiencing data corruption, I …

Sorry to ask that, i know there are tons of powerconsumption-discuss an optimization, and tewaking but i got lost. I just need to know how much Ampere a Nanopi NEO drains on fullload (4Cores), connnected with ethernet, no additional USB Hardware in default (no special h3consumtion). Especially boooting (i think armbian is throtteling on boot right?) is also very interessting. I need to buy a Powersupply which is sufficient for 15 NanoPi Boards in min and max consumption. Got very confused in reading the threads... But it seems 5V/2A is just a "be save in every situation" thing, and i think there is a "window" of throtttled booting and full-load 4 Core... So would…

With a little shell script I can switch gpio6 on/off: #!/bin/sh # PWM1 / GPIOA6 P=6 G="/sys/class/gpio/gpio${P}" if [ ! -d "${G}" ]; then echo "Exporting GPIO${P}" echo ${P} > /sys/class/gpio/export echo out > ${G}/direction fi i=100 while [ "$i" -gt 0 ]; do i=`expr $i - 1` sleep .2 echo 1 > ${G}/value sleep .1 echo 0 > ${G}/value done if [ -d "${G}" ]; then echo "Unexporting GPIO${P}" echo ${P} > /sys/class/gpio/unexport fi but I dont see anything which could enable PWM on this pin: root@nanopineo:~# ll /sys/class/gpio/gpio6/ total 0 -rw-r--r-- 1 root root 4096 Feb 21 11:38 active_low lrwxrwxrwx 1 root root 0 Feb 21 11:38 …

I want to use an ESP-12F to add wireless to my NanoPi Neo, but I don't think the Neo has broken out all the connections I'd need. Hackaday desctibes how to interface a Raspberry Pi B+ to an ESP-12F (https://hackaday.io/project/8678/instructions), but the Neo seems to lack some of the required pins. I like this idea since I've liked the performance and ability of every esp8266 system I've used. Their wifi network is solid, and they're low cost. Is this a lost cause or is it possible? Or perhaps this is a dumb idea? I'm not sure how well it'll perform vs a usb wifi modules, but the idea has captured my imagination.

Hi All. First post here (and quite a newbie). I have installed Armbian on my new NanoPi Neo and followed the instructions. It is all booting OK and I now wondering how I can attach a speaker directly to the header 10 LINEOUTR LINE-OUT Right Channel Output 11 LINEOUTL LINE-OUT Left Channel Output 12 GND 0V Will this work? How can I test it as I cannot see it with ALSAMIXER. TIA.

I'm missing something essential. I have NanoPi Neo v1.4 with Armbian 23.5 Jammy CLI (Linux nanopineo 6.1.30-sunxi). My display is Nokia5110 LCD or PCD8544 With spi-spidev DT I can successfully via `spidev0.0` with `spi-tools`. I.e. I confirm that spi is working. Now, I studied about DTO and fbtft driver, found that it supports pcd8544. I wrote this kind of DTO and added it to `armbianEnv.txt` /* * Device: LCD5110 (nokia5110) 1.6"(84x48px) SPI display Module PCD8544 * Module Connector * SDI(MOSI) <- PC0 * SCK <- PC2 * CS <- PC3 * RESET <- PA1 * DC/RS <- PA3 * LED <- PA2 */ /dts-v1/; /plugin/; / { compatible = "all…

Hi, I have a nanopi neo based on allwinner h3 chipset. I am trying to use an SPIDEV based driver for RF2401L (2.4 Ghz wireless module). I have used npi-config to enable the /dev/spidev0.0 device. However, when I try to use it to read status register of my module, I get wrong values. My SPI settings are Speed: 10kHz Bits: 8 Mode: 0 (CPOL=0, CPHA=0) To debug the issue I used a logic analyzer and found the clock signal rising up just before the MISO/MOSI activity. It shouldn't do that. When CPOL = 0, clock should be idle at 0. I am setting the SPI mode to 0. Here is the code void SPI::init() { uint8_t bits = RF24_SP…

Hi, i am actually a bit confused. I thought that a NanoPi Neo V1.0! which is set to 1200Mhz Clockspeed, enabled USB and enabled GPU should burn a additonal 1A (fast) Fuse while doing a 100% Stresstest. It doesn't. Just get more speed and heat... I added an additional Wlan Stick for more powerconsumption... but this doesn't help either. In my opinion and the always stated "on 912Mhz" max 2 Watts... it should kill the 1A on 1200Mhz no? 5V 2W = 1A ... I do a small cluster here and i want to save the GND Rail for shortage to save the other nodes if one Node is melted down and cause shortage. I thought a 1A Fuse has to burn up... but reality is kicking my …

I'm powering my NanoPi Neo V1.4 1801 through the USB type A port beside the Ethernet RJ45. I'm using Armbian 23.11.1 bookworm with kernel Linux nanopineo 6.1.63-current-sunxi. Now I want to enable the Micro-USB port (usually used for powering) to act as an USB host so that I can plugin an USB-stick. I found very few instructions for e.g. Orange Pi. There the device tree needs to be changed for usb@1c19000 and usb0-vbus. Also in armbianEnv.txt the line param_usb0_mode=0 should be added. But none of the instructions work for my NanoPi Neo. In the schematics, a SY6280 is connected via GPIOL2/USB0-DRVVBUS to the H3 cpu. …

Thanks to the latest Armbian and my own script - I now have a NanoPi Neo (two of them actually) running everything I want - Node-Red, Mosquitto, SQLITE3 etc..... got control of serial ports - marvelous. I have only one problem - I have no idea despite several experiments - how to get WIFI working on the standard cheap Wifi dongles you get on Ebay. (usually say 802.11n on the black plastic end). Anyone succeeded with this? Pete.

Hello all I want to control some GPIO pins on my NanoPi Neo (H3) board and installed WiringNP. Executing commands results in the error piBoardRev: Unable to determine board revision from /proc/cpuinfo I've traced the source of the error down to this line, where WiringNP tries to open /sys/class/sunxi_info/sys_info to determine which board it is running on. This path is not present in my Armbian os. I'm using 4.11.12-sun8i #20 SMP armv7l armv7l armv7l GNU/Linux Am I missing something here? Or are there alternatives to using WiringNP?

I'm running an updated armbian stretch mainline on a nanopi neo and hitting a wall where I thought there would be no obstacles in my path. I'm using 433Mhx Tx and Rx devices so I'm building WiringNP (from FriendlyArm) and rfoutlet (from github.com/timleland/rfoutlet.git). I'm getting errors such as wiringPi ISR: Not implemented when running RFSniffer. [This is the current error, it's been one after another]. My mind is muddled at the moment since I've done this kind of thing several times in the past on other devices including the Orange Pi Zero. Can someone tell me if this is me, or if it's a NanoPi Neo-thing? Shouldn't this be straight-forwa…

Don't quite know what to expect here. The download page implies that there should be a gadget serial connection but there is nothing. I don't even see the USB DRC getting registered. Is this a known issue and is there a solution? TAIA. # nanopineo:~$ uname -a Linux nanopineo 4.11.3-sun8i #3 SMP Wed Jun 7 13:28:34 CEST 2017 armv7l armv7l armv7l GNU/Linux # nanopineo:~$ lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M # nanopineo:~$ lsmod Module Size Used by evdev 20480 1 brcmfmac 172032 0 brcmutil …

I didn't see support specifically for NanoPi NEO-LTS https://www.friendlyarm.com/index.php?route=product/product&product_id=132 Does one of the other images work on this particular board?

Hi, There is a fresh new install. armbian-config fails with a message "There are no targets. Please check your drives". BOARD=nanopineo BOARD_NAME="NanoPi Neo" BOARDFAMILY=sun8i VERSION=5.65 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage System diagnosis http://ix.io/1sm3

Nano Pi Neo, Armbian (Armbian_5.27.170422_Nanopineo_Ubuntu_xenial_dev_4.10.11) External USB device works fine when connected via USB-A jack, but doesn't work when connected to 2.54 pin header (2,3). Is there some additional steps to activate internal (usb1, usb2) ports, or it's hardware problem?

anyone running a neo+ 2. don't bother with neo2 image, it doesn't recognise emmc or wifi card the nanopi K1plus image works beautifully and supports both emmc and wifi module

As per the Subject, the I2C bus 0 is enabled and detected, but I don't see an addresses being returned when I try the i2cdetect -y 0 command. I have a single PCF 8574A connected with address 0x38. and have double checked the wiring. The PCF8574A did respond on the I2C bus on another SBC. Thanks John

Today I did get my NAS-Case "Neo Station NS-120B" for my NanoPi Neo2 (also useable with a normal NanoPi Neo). Because I already did use the Neo2 with armbian (and had soldered all pins on the mainboard - I ordered only the case without a new Neo2 with soldered pins) I didnt want to write the FriendlyARM Image for NAS to my uSD. After completing to built the Neo2 and the 2.5 HDD inside the case (and using the 12V PowerSupply I had) armbian did start up and I could normally SSH into my Neo2 - BUT I cant see the HDD or the HDD-controller (which should be connected via USB). ( @tkaisernow here the Neo2 do get his power over pins and not via the Mic…

Good day! I've had the Nanopi Neo2 v1.0 for sometime now, used for mostly for NAS solution. the v1.0 is the one being carried by my supplier here. No v1.1 yet Lately I installed armbian monitor to monitor system resources. Then I stumbled upon the min and max frequency when I checked using # cpufreq-info -p 408000 816000 ondemand I've read on some internet writeups that one can set the max frequency to 1008000 tried editing the cpufrequtils scaling_max_freq scaling_available_frequencies scaling_setspeed I was able to lower the minimum frequency to 120000 using the following entry…

Hi! I've recently bought a nanopi NEO2 which features an Allwinner H5. On FriendlyArm website (and on Allwinner's too) it is stated that the H5 is clocked 1.5Ghz. I need to perform some heavy job and and noticed that the cpu frequency hits, at full power, only 1Ghz. I checked using cpufreq-info and I got: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: 244 us. hardware limits: 120 MHz - 1.01 GHz available frequency steps: 120 MHz, 240 MHz, 312 MHz, 480 MHz, 624 MHz, 816 MHz, 1.01 GHz available cpufreq governors: conservative, ondemand, users…

NanoPi NEO2 Debian jessie 4.11.1-sun50iw2 mount.cifs doesn't load if iocharset=utf8

Hi,I want to know how to disable serial console /dev/ttyS0 on NanoPi NEO2 with allwinner H5. My Environment: Board:NanoPi NEO2 uname -a: Linux nanopineo2 4.14.4-sunxi64 #11 SMP Thu Dec 7 11:55:12 CET 2017 aarch64 aarch64 aarch64 GNU/Linux dmesg | grep tty: [ 0.000156] console [tty0] enabled [ 1.655315] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 24, base_baud = 1500000) is a U6_16550A [ 1.655383] console [ttyS0] enabled [ 1.678058] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 25, base_baud = 1500000) is a U6_16550A [ 1.700706] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 26, base_baud = 1500000) is a U6_16550A [ …

I used the Armbian test image. I did apt-get upgrade I changed eth0 to static IP. But now, I started it up and eth0 green light won't stay on. Can't ping it or SSH. I connected a USB PL-2303HX from my PC to the NanoPi Neo2 (first time for me ever connecting to a Linux computer's serial console) With no configuration at all I got this output in minicom. U-Boot SPL 2017.09-armbian (Sep 17 2017 - 03:48:48) DRAM: 4096 MiB Trying to boot from MMC1 …

Today I did update my 3 NanoPi Neo2 via apt update/upgrade, but only one is accessable via ssh after the update. (without SSH/SSL-conect also no conection via SFTP/WinSCP because if the timeout) The one which is accessable has after the update Welcome to Armbian 23.02.2 Bullseye with bleeding edge Linux 6.7.12-edge-sunxi64 ( Machine model: FriendlyARM NanoPi NEO 2) The two other do show prompts for user/password but doesnt login via ssh - and after some time they time out and I can reenter user/password After connecting via TTL-serial I can also enter user/password and then the Neo2 shows me: _ _ ____ _ _ _ …