Allwinner sunxi

I want to downgrade the kernel because auf random freezes on my Banana Pi and was following this tutorial to downgrade to Mainline stable kernel (Armbian 5.31): At apt.armbian.com I can find all required packages except for: linux-firmware-image-next-sunxi According to the linked thread I need this package otherwise the system may not start anymore. Could someone tell me where to find that package? Thanks :-)

I got AT070TN90 display and I am trying to get 800x480 resolution on it. root@orangepipcplus:~# uname -a Linux orangepipcplus 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l GNU/Linux trying "h3disp -m 800x480" and "h3disp -m 31" does not give any results , it is working on -m 32 but everything is too small .... than I tried to edit script file , but with no success any ideas ?

Hi, I'm using an Olimex Lime 2 board with the debian jessie image and 4.1.6-sunxi kernel. Is there a way to look at the battery state?

Normally the 'shutdown now' sequence makes my monitor 'lost connection' message appear but with this image the shutdown process do not finalize correctly...

Maybe a discussed problem. Using Armbian Jessie on Banana Pi M1. Using USB keyboard and Mouse. Can use usb wifi adapter but presently unused. Power supply standard PS for Banana Pi normal output from lsusb and lsusb -t But it won't read files from usb key. Why ? can you help?

I have a NanoPi Neo Core with eMMC..I have installed armbian os from "https://www.armbian.com/nanopi-neo/" to sd card and tried the "Armbian configuration utility" and "nand-sata-install" to install os to eMMC. But it is showing "there are no targets..please check your drives."..If we give "fdisk -l" command it is not detecting the eMMC. How to solve this issue??

Orange pi one refuse to add spi to /dev/. It's 5.73 armbian kernel 4.19.20-sunxi. I've activated spi dev from armbian-config but no device after reboot. Gpio and i2c work great . Anyone had problem like this? Послато са Redmi Note 6 Pro уз помоћ Тапатока

Hi, I want to use g_ether on NanoPi Neo Plus2. For Neo Air, I have already figured out how to do this and I can see usb0 in config. But with armbian 5.85 (4.19.38-sunxi64), the same instructions fail at sudo ifconfig usb0 up with the message "usb0: ERROR while getting interface flags: No such device". Could somebody tell me how to activate USB OTG on NanoPi Neo Plus2 and then use g_ether. I think the same holds true for g_serial. This could be an alternative, but I would prever ethernet connection. My target: Connect NanoPi Neo Plus2 with NanoPi Neo Air via Ethernet Thank you for your help! Steps I followed for g_ether:

Just a quick question due to having just updated and rebooted my Cubietruck.... I was running 5.38 mainline Stretch, but I see that armbian-firmware 5.45 was installed over 5.38... so shouldn't the welcome screen now be saying "Welcome to ARMBIAN 5.45" instead of "Welcome to ARMBIAN 5.38" still? Or is that package not the one that determines the Armbian 'version'? Maybe a better question would be what would update /etc/armbian-release ? The update process was otherwise smooth and doesn't seem to have rise to any nasty surprises . I also look forward to trying out the pineH64 image since I see that has just made a big jump, as well as th…

Is there a way to compile MAME for the OPI PC? Many thanks in advance!

Hello Armbian-Folks, more than two years ago I purchased a CubieTruck and installed Cubian with kernel 3.4.79 on the microSD. The system is running since then and serving as airprint server, boinc client and monitoring device for my internet connection. Basically I use it more or less as a headless server. Now I would like to have this system more future ready and looking for an upgrade path. The kernel is quite old and the distro is based still on debian wheezy. Also Cubian is dead and not maintained anymore. Are you able to help or provide some good starting tipps to upgrade my system to new kernel and maybe armbian (debian jessy) as distro? I was search…

Hi, is it possible to run xfce4 on mainline on a Orange Pi Zero? I'm doing it with jessie legacy (I need to have a mumble client running, accessing it with X11vnc) but I wanted to upgrade. I've tried the same setup but without any luck. apt-get install --no-install-recommends xserver-xorg apt-get install --no-install-recommends xinit apt-get install xfce4 xfce4-terminal tango-icon-theme gnome-icon-theme lightdm lightdm fails to start on boot and startx tells me: Fatal server error: (EE) no screens found(EE) Have somebody done it and can it be done easily?

Hi there, i needed to recreate my cubietruck as a VDR with a brand new image. I´ve choose the plain http://mirror.igorpecovnik.com/Armbian_4.2_Cubietruck_Debian_jessie_4.1.6.zip image to install but after booting it got stuck at "Welcome to Debian GNU/Linux 8 (jessie)!" and after many minutes " (TIME) Time out waiting for device dev-ttyS0 device. (DEPEND) Dependency failed for Serial Getty on ttyS0." appears. I downloaded the 3.4.108 kernel image which installed and ran ok apart of that the USB connection dropped after a while which is a problem for my VDR: [ 8.301636] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 8.306840] eth0: PHY ID 001cc915 a…

The eth0 device does not work when using 6.1.47-current-sunxi64 and 6.12.20-current-sunxi64 kernels. There will be the following errors in the kernel log. pi@orangepi3:~$ dmesg | grep eth0 [ 16.997431] dwmac-sun8i 5020000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 16.998219] dwmac-sun8i 5020000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19) [ 19.284111] dwmac-sun8i 5020000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 19.284754] dwmac-sun8i 5020000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19) [ 19.308140] dwmac-sun8i 5020000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 19.308738] dwmac…

Hi guys, Quick question about the USB ports on the Cubietruck. Once I am done with the usual setup procedure (changing the root password and setup a user) system reboot. I sometimes end up in situations where I need to access the Cubietruck directly and not through ssh. In such situations I noticed that my usb keyboard and mouse do not respond at all, eventhough if these are the exact same ones hich I used to the 1first time setup. What could be the reason for this ? Thx,blub4747

Hi, to resume the problem I encounter please let me introduce the network I use. 1) a main modem/router called BBox2 which is a Sagem F@st 3464 connected in LAN-WAN to a 2) a secondary router called Lamobo R1 (also named Banana Pi R1 = BPi R1) 3) a laptop connected to the BPi-R1 4) I think to connect IP camera to the BBox2 then need to stay in the same network range (so I presume I need to change the conneciton used in 1) from LAN-WAN to LAN-LAN isn't it ?) Here is the connections and IP Addresses : BBox2 is connected in LAN-WAN to the BPi-R1 ISP -> BBox2 (LAN) -> (WAN) BPi-R1 (LAN) -> (LAN) Laptop 192.168.1.1 (DHCP->) 19…

I got OPi with the 2xUSB official HAT and noticed that it is running very hot: 52 when starting and going to 62 after a while - just idling: Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:56:12: 912MHz 0.20 2% 1% 0% 0% 0% 0% 55°C 18:56:17: 240MHz 0.18 2% 1% 0% 0% 0% 0% 54°C 18:56:23: 240MHz 0.25 2% 1% 0% 0% 0% 0% 56°C System is: # cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepizero BOARD_NAME="Orange Pi Zero" VERSION=5.24 LINUXFAMILY=sun8i BRANCH=default ARCH=arm Linux orangepizero 3.4.113-sun8i #50 SMP PREEMPT Mon Nov 14 08:41:55 CET 2016 armv7l GNU/Linux (no SPI flash,…

Hello, The Orange Pi 3 ARMBIAN image is no longer available on ARMBIAN Website, is there any way to get it ? https://www.armbian.com/orange-pi-3/ Thanks

Good day Armbian Forums! I'm having some trouble with builds of Armbian (up to and including 21.08.6 | kernel 5.10.60-sunxi) seeing wireless access points that are configured to channels 12 & 13 on my Orange Pi Zero Plus2 boards (H3 + 256mb RAM). Specifically, the default Android image (a generic Chinese-language Android multimedia system) that's loaded onto these boards can see and connect to access points that have been set to all channels (1-13) successfully, but any Armbian image I have tried fails to see anything (and subsequently cannot connect) to routers on channels 12 & 13. Due to the nature of this, I believe it may be a region setting or dri…

im using banana pi m1 trying to play around with gpio therefore tried almost every library for it, but found nothing working is there anything else i should do other than installing libraries?? like wiring 2 python LMK.GPiO etc. where should i start from as a beginner??

Hi all, I've one minor issue with my Lamobo R1. I've to set the coherent_pool to > 256KiB to get my USB DVB device working. But every time I set the coherent_pool to e.g. 2M and regenerate the boot.scr the device gets in an endless boot loop (starting uboot - starting kernel - changes resolution and starts to load drivers - but then crashes with graphic errors and starts all over again). Is there something I can do against this? I've compiled the v3.0 with Jessie 3.4.107 with following kernel paramters configured (and sunxi uboot v2015.04): MEDIA_SUPPORT=m VIDEO_DEV=m SOUND=m GMAC_FOR_BANANAPI=y CMA=y CMA_SIZE_MBYTES=16 Greetings, Oliver

If I open the image file for NanoPi NEO, I don't see the FAT32 boot partition. > fdisk -l Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img Medium Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img: 1,4 GiB, 1488977920 Bytes, 2908160 Sektoren Einheiten: sectors von 1 * 512 = 512 Bytes Sektorengröße (logisch/physisch): 512 Bytes / 512 Bytes I/O Größe (minimal/optimal): 512 Bytes / 512 Bytes Typ der Medienbezeichnung: dos Medienkennung: 0xbcf97591 Gerät Boot Start Ende Sektoren Größe Id Typ Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img1 8192 2908159 2899968 1,4G 83 Linux If I flash…

Hy, I use Cubietruck / Armbian I have a problem with I2C connecting to an Arduino. my Python program returns me an error when I use the SMBus module : read_byte_data the function (address, reg) bug while writing functions work well. here is my Arduino code : #include <Wire.h> #include <LiquidCrystal.h> #include <string.h> #include <ctype.h> const int RS = 12; const int E = 11; const int D4 = 5; const int D5 = 4; const int D6 = 3; const int D7 = 2; LiquidCrystal lcd(RS,E,D4,D5,D6,D7); #define SLAVE_ADDRESS 0x12 byte regs[3]; int regIndex=0; byte lastExecReq = 0x00; char message[20]; void setup (void){ regs[0] = 0x00; regs[1] = 0x00; …

Hello, I am new to Nanopi platform. I want to use nanopi m1+ as a wifi access point. How should I go after it from starting?

Hi, I tried two builds for my OPI Zero. Armbian_5.35_Orangepizero_Debian_jessie_next_4.13.16.7z Wifi works but no audio. (and instabel ethernet connect) Armbian_5.35_Orangepione_Ubuntu_xenial_default_3.4.113.7z Audio works but no WiFi In witch build works both ?

I am having a problem setting up the wireless on OrangePi PC Plus. Kernel module 8189fs is loaded, but no wlan0 interface appears. Here is my lsmod output: root@orangepipcplus:~# lsmod Module Size Used by rfcomm 32863 4 bnep 9617 2 bluetooth 174065 8 bnep,rfcomm mali_drm 2732 1 drm 178255 2 mali_drm sunxi_cir 1601 0 pcf8591 3363 0 bmp085 3487 0 mali 123208 0 ump 29379 3 mali 8189fs 1050451 0 hid_logitech_dj 10040 0 ifconfig and iwconfig do not show an…

RT, i am trying to use git and aarch64 tools to compile a lastest u-boot by my own,but ,it failed. there're the steps i was doing: 1. downloads the latest u-boot source code from offical web: git clone git://git.denx.de/u-boot.git 2.downloads the ARM Trusted Firmware from offcial web: git clone https://github.com/ARM-software/arm-trusted-firmware 3.compile the ATF for BL31 by using this cmd: sudo make CROSS_COMPILE=aarch64-linux-gnu- PLAT=sun50i_h6 all and then move the BL31 file into the u-boot root fold. 4. compile the u-boot for H6 by using this cmd: sudo mak…

Hello, I just updated my pcduino3 nano with armbian mainline 4.9.7 download on SD card and now the onboard ethernet port fials. I am using a USB to ethernet for now with no problems. Below are the messages I get during boot Feb 22 14:35:23 localhost kernel: [ 2435.162554] sun7i-dwmac 1c50000.ethernet: Failed to reset the dma Feb 22 14:35:23 localhost kernel: [ 2435.168668] stmmac_hw_setup: DMA engine initialization failed Feb 22 14:35:23 localhost kernel: [ 2435.174517] stmmac_open: Hw setup failed I have tried several times to reset via cli and NetworkManager with the same results. ip a & ip link show as down seen in ifconfig but not able to ch…

Hello, Thanks for making ARMBian! I would like to be able to use it with my Orange Pi Zero LTS to make a PI-Hole. I'm using Armbian_19.11.3_Orangepizero_buster_current_5.3.9 However, I keep having problems with locales, such as : Warning: Invalid locale (please review locale settings, this might lead to problems later): locale::facet::_S_create_c_locale name not valid How can I fix it ? Thank you.

Dear Sirs and Madams! I am working on custom minimal image for NanoPi NEO and I've managed to solve majority of problems, however, if I observe boot process via /dev/ttyUSB0, I still get these two errors: HELLO! BOOT0 is starting! boot0 version : 4.0.0 boot0 commit : 1b3a1b587482affdd18aba923de7fe38eb7d5ee1 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V1.3 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the ch…

Hello, i can't hear any audio out of my cubietruck. This is my system: root@cubietruck:~# uname -a Linux cubietruck 3.4.109-sun7i #4 SMP PREEMPT Sun Oct 11 14:32:15 CEST 2015 armv 7l GNU/Linux root@cubietruck:~# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 8.3 (jessie) Release: 8.3 Codename: jessie root@cubietruck:~# cat /proc/asound/cards 0 [sunxicodec ]: sunxi-CODEC - sunxi-CODEC sunxi-CODEC Audio Codec 1 [sunxisndspdif ]: sunxi-sndspdif - sunxi-sndspdif sunxi-sndspdif 2 [sunxisndi2s ]: sunxi-sndi2s - sunxi-sndi2s sunxi-sndi2s …

Hi, I have recently upgraded Armbian as suggested with: apt-get update apt-get upgrade apt-get install -f apt-get upgrade apt-get autoremove -y After that i2c-0 stopped working: Output if i2cdetect -y 0 before upgrade: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- --…

My Orange Pi PC running Armbian gets disconnected from both SSH and VNC after maybe 20 minutes or so out of nowhere, no matter if idle or doing anything. I can't connect back until I restart the entire SBC by keyboard. The pi is useless to me if I can't run it "headless". I'm wondering if it's a MAC problem. I have a pfSense router I built myself and have had different subnet addresses. I've made sure the MAC address isn't repeated on another subnet address, though. I know the Raspberry Pi has a way to change it, but does the OPi PC as well? The MAC "problem" is just a guess, though. I really don't know what's with the disconnection issues. I'm no …

Hi, couple of month ago I installed Armbian on my Cubietruck. I didn't really use it much, but today I decided to start using it, and obviously the right way to do so is to update to the latest version. So when I started, I had this version on my Cubietruck: ARMBIAN Ubuntu 14.04.4 LTS 3.4.112-sun7i I followed Igor's instructions at http://docs.armbian.com/User-Guide_Getting-Started/#how-to-update : apt-get update apt-get upgrade apt-get install -f apt-get upgrade apt-get autoremove -y However, I received the following error message after the first instance of "upgrade": ... Setting up linux-firmware-image-sun7i (5.20) ... Setting up linux-headers-sun7i (5.20)…

Hi there, I am new to OrangePi and Linux as well and that's probably why I have faced my first problem I could not find an answer on web. I use OP Lite with the latest debian jessie. And there is the problem (or just a bug): after some time of using WiFi (and wwan) I wanted to disable it in order to reduce "excessive" power consumption. So firstly I had disabled it via "nmcli" and after a while I found out about "h3consumption" command. But recently I wanted to install (and download) but none of the above commands were able to re-enable them. Any ideas how to re-enable (besides loading new OS image) ? In addition, I noted that changind "h3consumption" is not a…

I'm trying to figure out what happened in my device this morning. the process that i'm monitoring was interrupted and restarted and i'm want to know that reason, is it internal code reasone or system failure that caused to my process to crash. i'm attaching the /var/log/message piece of logs when my process crashed. can you tell me what happened? I'm using NanoPi2 NEO with latest armbian version for this specific board, Thanks alot Spoiler Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1753] dhcp4 (eth0): address 10.0.0.5 Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1822] dhcp4 (eth…

When I have to use Jessie version dev with kernel NEXT 4.13.5. The alsamixer have different options to setup audio compare to ARMBian with stable kernel 3.x I must switch on DAC Reversed to have audio output in speakers. I don't know it is correct but works for me. The input mic is very sensitive and must be lower value to have good quality sound I don't know why is displayed option for MIC2 , the orange pi zero has only one microphone input

Hi All I use Cubieboard2_Debian_3.8_wheezy_3.4.107.raw for my Cubie2 (2012-09-09). Looking at [uart_para3] in the fex (created with bin2fex after nand install) [uart_para3] uart_used = 1 uart_port = 3 uart_type = 4 uart_tx = port:PH00<4><1><default><default> uart_rx = port:PH01<4><1><default><default> uart_rts = port:PH02<4><1><default><default> uart_cts = port:PH03<4><1><default><default> I check if the pins is used by other 'function' And found that it used by lcd1_para [lcd1_para] ...snip... lcdd0 = port:PH00<2><0><default><default> lcdd1…

I'm looking at GPIOs and I'm not sure - can I buy an "old" (26 pin) Raspberry Pi gpio adapter-breadboard-cable package (like this one) and use it on Orange Pi Zero GPIOs as on Raspberry Pi GPIOs?

Hi, I am using Linux nanopiair 3.4.113-sun8i distribution on my Nano Pi Neo Air and trying to get the g_ether works. After using modprobe g_ether and set up the network/interfaces auto usb0 iface usb0 inet static address 192.168.0.2 netmask 255.255.255.0 then edit /etc/modprobe.d/g_ether.conf: options g_ether host_addr= 06:7b:95:4c:59:d7 After reboot it shows: [ 6.868451] usb0: MAC 06:7b:95:4c:59:d7 [ 6.868475] usb0: HOST MAC 5e:5b:65:8f:94:85 [ 11.484526] systemd[1]: Found device /sys/subsystem/net/devices/usb0. [ 16.249726] ADDRCONF(NETDEV_UP): usb0: link is…

Hi Experts, I have a strange issue while Armbian installation to my Orange PI PC boards. So there are two SD cards with the same parameters: 1. smartbuy 8gb sdhc class 10 2. OltraMax 8gb sdhc class 10 The problem is that when I use smartbuy card I can install Armbian and it works fine. But when I use OltraMax card I can install Armbian but after first login it asks me the following: Warning: a reboot is needed to finish resizing the filesystem Please reboot the system as soon as possible Ok, I do a reboot and Orange PI PC can't boot Armbian after. Moreover as can I understand I get a boot loader (u-boot) console …

Which system to install on Orange Pi Plus 2 ? http://www.armbian.com/orange-pi-plus/???

Hi, I moved from Jessie to Stretch. On Jessie i looked under a scope and generated SCK (Orange Pi Lite is Master) is clean. However, after i switch to Stretch, my SPI Slave doesn't work anymore and further investigation reviews that it has similar problem as previous builds that extra clock cycle is generated before data is transfered. The behaviour is exactly similar to following image posted by another forumer but for earlier builds. I am not sure whether any of you experience the same problem. Thanks my armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=…

So.. this neat board has mainline kernel but with no video output and it has a mali panfrost GPU. My question to all you dev pros of the kodi tv boxes is... Is there anyone capable to fix video output on this wee board that has it on radxa 5.15 default debian kernel?

It used to function fine, however after not using it for awhile it has quit working. It starts booting normally, then hangs with what's visible on the screen being a bunch of systemd messages, with the last being either something about system variables or mounting FUSE file filesystem, when it's the latter it's followed up with a kernel panic. I've reflashed several times using both the server and desktop images freshly downloaded, no difference. The power supply I'm using worked before, as did the SD card. Unfortunately I have no way of showing you system logs or such for the time being. Any help would be appreciated.

I am not able to run this on Cubietruck. Just struck on starting kernel.......it does not go beyond this. I have tried both 3.4 and 4.1 kernels...... Thanks.

I just got 4 NanoPi Duos v1.1 and the OTG port functions (unlike v1.0)! This is with the FriendlyElec image. I was wondering should I compare the FriendlyElec's sun8i-h2-plus-nanopi-duo.dtb to the one on Armbian? I already tried messing with Armbian's sun8i-h2-plus-nanopi-duo.dtb by changing usb@01c19000 status = "okay" and adding dr_mode = "host". I'm not sure I can just drop in the dtb? Any way, I'll see what I can figure out. I'm excited the OTG port works now for more than just power since that saves you from buying the Mini Shield if you have a simple project that just needs a USB drive or camera.

TKaiser. If you install the Desktop version of Armbian 5.10 then the following list of codecs (containing h.265 with 8 bit but not 10 bit!) is available for HW accelerated decoding: http://linux-sunxi.o...ed_codec_matrix Is 8 Bit versus 10 Bit a limitation. Can the Orange Pi PC with Armbian 1.10 decode all HEVC 8 or 10 bit encoding to 8 bit decoding, or can it ONLY do 8bit encoded to 8 bit decoding? Seasalt

Hi, in the last weeks I'been trying to use the serial ports 5 and 6 (tty5, tty6) of the cubieboard2 using DTB but still not working. First of all, I must said that i'm not a linux expert, only a linux user with some experience and all the information below is the result of multiple weeks of internet research. for the moment i'm able to get the cubieboard2 to recognize the ports, and using a c++ program I write on all serial ports, i get a response from tty0 but can't get the gio pins of the serial ports 5 and 6 to work. here is what I have done so far: first, I downloaded the device tree compiler sudo apt-get install device-tree-compiler then, nav…

Hi there, I have configured (successfully with NetworkManager GUI, or TUI, it was quite ago, can see it in /etc/NetworkManager/system-connections/ ) my OPi3 as an WiFi AP. (Needed this as sharing "normal" LAN traffic with video surveillance on same WiFi channel was a disaster). It works, but in "scan" on OpenWRT routers this WIFi shows only as WPA not WPA2 protected. Armbian Buster 21.02.3. Why? How to correct this? Laurent

I installed the image Armbian_20.08.1_Orangepiplus2e_focal_current_5.8.5_desktop.img on my Orange PI Plus 2E and I installed RetroArch to setup a retro gaming board. Everything installed ok but all games even weak games like for Super Nintendo, are running slow and no audio, does anyone here already tried to get RetroArch working on this board? Audio is not working , it uses pulseaudio and it's installed already. I already tested RetrOrange Pi image, it uses Armbian too I guess, most of the games runs at full speed, the reason I am not using is that is a little outdated, some emulators doesn't work and some are missing and I personally …

Hi, Just as my last post. I want to know if it is possible to wakeup opi3 after I switch its state to "mem" or "disk" using gpio on CON12. I have doing some reasch but I don't know if it is right: PL/PM port can be used as wakeup source. PF/G/H/L/M port support interrupt event. PC/D didn't support interrupt. But when I try to write a device tree file, but it just report some error with error code -22. My device three is like this: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h6"; /* * This fragment is needed only for the internal pull-up activation, * external pull-up resistor is highly recommended if using long wires */…

LANG=en_CN.UTF-8 I have it+SD card+usb TouchScreen+HDMI Screen which work with http://www.orangepi.org/'s image. I've downloaded https://dl.armbian.com/orangepilite2/Debian_stretch_next.7z,verified the sha256 checksum,burn SD card,verified checksum of SD card... After UBoot, nothing was displayed,but `fdisk -l /dev/sdb` changed -------------------------------- Disk /dev/sdb: 30 GiB, 32220643328 bytes, 62930944 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x16977123 Device Boot Start En…

Look at the description https://docs.armbian.com/User-Guide_Armbian_overlays/ when I set UART I2C in armbianEnv.txt it should be overlay_prefix=sun50i-h616 overlays=i2c3-ph uart5-ph as described on the given page But when I use armbian-config and go to Manage Overlays my settings are not seen and I have to set them but the names of all overlays are preceded by the prefix. After selecting and saving the settings in armbinEnv.txt it is overlay_prefix=sun50i-h616 overlays=sun50i-h616-i2c3-ph sun50i-h616-uart5-ph as a result the defined overlays are not loaded Is it supposed to be like t…

Hello, i update my OrangePiZero OS from Linux 5.10.43-sunxi to Linux 5.10.60-sunxi my screen fbtft spi lcd stop working , the screen is black. If there is a solution to this issue I would love to get help, thanks! here my configuration (work on 5.10.43). (Armbianmonitor link of 5.10.43 on top) (Armbianmonitor link of 5.10.60 Attached as a file ) fbtft.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; }; }; fragment@1 { target = <&pio>; __overlay__ { spi1_cs_pins: spi1_cs_pins { pins = "PA13"…

Is there a kernel package with PREEMPT-RT for OrangePi PC Plus? I'm trying to get linuxcnc running - which works, but without USB. I used this guide: https://orangecnc.gitlab.io/quick-start.html. Kernel there is 5.4.18, which has the USB-not-working-bug for Orange Pi Plus.

Sorry if I miss something, but it seems debian is no more available for download on this page https://www.armbian.com/orange-pi-zero/ Do you have any information please?

Hello, Has anybody successfully used the IR sensor on Banana Pi M2? From this, after I load the sunxi-cir module, I should see the sensor in /sys/class/rc/ but I see nothing. Nothing on dmesg either. Anyone who could point me in the right direction?

Hello guys, apparently there is a new product in the orangepi lineup. It is the PC+ (PC Plus), which has 8gb EMMC and a Wifi chip onboard. The rest of the features seems to be the same as the plain OrangePI PC. The new SBC can't be found on the orangepi official site, but it is available on aliexpress: http://www.aliexpress.com/store/product/Orange-Pi-PC-Plus-ubuntu-linux-and-android-mini-PC-Beyond-Raspberry-Pi-2/1553371_32668618847.html

Hello everyone I have an orangepi zero with a Micro-USB (OTG) socket and an A-USB socket integrated into the board. Using the Armbian_5.35_Orangepizero_Ubuntu_xenial_next_4.13.16 system, a micro-USB cable connected to a Windows computer will have an ELMOG MAS COM device that makes it easy to manage orangepi zero. However, this Micro-USB socket is easily damaged after many times of plugging and unplugging. Can I use the A-USB socket as the USB device mode? thank you all

Is it possible to include an older kernel in my build? Something along the 3.x era? I really need to get an OV5640 working, and it would seem that 5.x kernels don't work with it. The thread is for an orange Pi, but I have a banana pi. Either way, it's an allwinner A20 and I've struck out getting the camera to be detected.

Hi Forum, "modprobe g_mass_storage file=/dev/sda1 removable=yes stall=0" doesn't work on 3.4.112 but works on 4.6.2. [ 363.575922] [sw_udc]: [sw_usb_udc]: binding gadget driver 'g_mass_storage' [ 363.581661] [sw_udc]: alloc request: ep(0xc0a75608, ep0, 64), req(0xee461c00) [ 363.590722] WRN:L2728(drivers/usb/sunxi_usb/udc/sw_udc.c):ERR: usb device is not active [ 363.597754] usb open backing file: /dev/sda1, 0xee42fa00 [ 363.604178] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11 [ 363.608029] g_mass_storage gadget: Number of LUNs=1 [ 363.612001] lun0: LUN: removable file: /dev/sda1 [ 363.619227] ep_matches, wrn: endpoint already claimed, e…

Greetings, I've got 2 M1 boards in front of me. The FA is running their latest distribution: http://www.mediafire.com/file/kc44mm1mdahslho/nanopi-m1_debian-jessie_4.11.2_20170905.img.zip By default the device tree for the FA has the USB controller (usb@01c19000) marked as disabled and is missing the dr_mode = "OTG" attribute. Enable the controller and Add the dr_node property and the board comes up as a mass storage device in both Windows and Linux. The board running Armbian has exactly the same device tree entries, dmesg shows the USB controller is loaded and visible with lsusb -t. When a gadget module is loaded all appears to work on…

No nameserver in these files too /etc/resolvconf/run/resolv.conf /run/resolvconf/resolv.conf The nameserver is set in this file only /run/NetworkManager/resolv.conf This is the content of /etc/NetworkManager/NetworkManager.conf [main] dns=none plugins=ifupdown,keyfile [ifupdown] managed=true [keyfile] unmanaged-devices=interface-name:p2p0 These are relevant lines from systemd journal: Oct 29 21:47:24 orangepilite NetworkManager[507]: <info> [1509306444.9814] dhcp-init: Using DHCP client 'dhclient' Oct 29 21:47:29 orangepilite NetworkManager[5…

HI All, I am trying to install the driver for Dlink (DWA 131 - Rev E1) wifi (usb dongle ) on my Olimex A20 borad (with Armbian ubuntu - legecy kernel 3.4.113-sun7i ) . folllowing this procedure 1. I downloaded the Offical D-Link Driver here 2- install the kernel header files : - sudo apt-get install linux-headers-sun7i - cd /usr/src/linux-headers-3.4.113-sun7i/ - make scripts 3 -make ARCH=arm // this make is for driver compiling but I got a bunch of errors like : /usr/src/linux-headers-3.4.113-sun7i/rtl8192cu-fixes/core/rtw_security.o: In function `is_multicast_mac_addr': rtw_security.c:(.text+0x1f94): multiple defi…

Hello, is the new Orange pi Zero LTS supported by Armbian? It's the same chip and same stuff but they claim they have reduced the power consumption and lower the board’s temperature. Do you think they have archived that by manipulating the hardware or by lowering the frequency and stuff via software?

Hi every one I installed armbian on my orange pi win plus. I want to use all uarts. uart1, uart2 and uart3. uart2 is enabled by default but the others are not. I add "overlays= uart1 uart2 uart3" in armbianEnv.txt but they don't work. Additionally, there is not /alwinner/overlays directory in /boot/dtb. And there are ttyS0, ttyS1,ttyS2 and ttyS3 in /dev directory.. So..How can I enable the other uarts? thank you

Hello, I've been trying to interface Kedei hdmi 3.5 inch hdmi lcd (480x320) with orangepi one. So far i"ve been unable to display anything on lcd using Armbian mainline kernal image. But with legacy kernal using h3disp command i was able to change the resolution but the lcd than gave message " Not Supported". Can someone please help me how to do this?

Hi all Given that the node that H3 consumption uses to change DRAM frequency no longer exists on H5 on the mainline kernel, how would one go about altering this?

Hi All, I seem to be encountering an issue with setting the MTU for the 8189fs driver on the 4.10.0-sun8i kernel I am trying to set the MTU for wlan0 to 1532. Note this works on the 3.4.113-sun8i kernel without issue. #uname -a Linux orangepipcplus-02c0008115dff7be 4.10.0-sun8i #10 SMP Sun Feb 12 16:51:59 AEST 2017 armv7l armv7l armv7l GNU/Linux /etc/network/interfaces ---------------------------------------------------------------------------------------------------------------------------------- auto wlan0 iface wlan0 inet6 manual wireless-channel 1 wireless-essid batnet6 wireless-mode ad-hoc wireless-ap 02:13:13:13:13:13 …

i have banana pi m2plus and compile latest armbian after starting x11, i get "could not connect to wicd's d-bus interface..." no error shown in /var/log/wicd/wicd.log and wicd seems to be working also bcmdhd loaded, but when trying to connect wifi, cannot get ip any idea?

Hello, my external USB3.0 HDD is only recognized with USB 1.1. dmesg | grep usb: [ 0.180455] usbcore: registered new interface driver usbfs [ 0.180455] usbcore: registered new interface driver hub [ 0.180455] usbcore: registered new device driver usb [ 2.470043] usb 2-1: new high-speed USB device number 2 using sunxi-ehci [ 2.610042] usb 2-1: device descriptor read/64, error -71 [ 2.694427] usbcore: registered new interface driver usb-storage [ 2.716481] usbcore: registered new interface driver ums-alauda [ 2.728259] usbcore: registered new interface driver ums-cypress [ 2.740098] usbcore: registered new interface driver ums-datafab …

I'am running a PiOne with 4.14.14 Stretch. I have installed acpid and give the command acpi_listen When pussing the button in Stretch and I didn't see any logging. With the old kernel in 5.38 Jessie on the same PiOne I saw button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 In the output of dtc /boot/dtb/sun8i-h3-orangepi-one.dtb I saw key_pins@0 { pins = "PL3"; function = "gpio_in"; linux,phandle = <0x39>; phandle = <0x39>; }; Means gpio_in defined as an input? Is the button function not yet implemented in 4.14.14? Or is something going wrong?

https://paste.armbian.com/faquvejaxo works ok for my alternate 2G4 network. Scanning wifi does not show any 5G8 networks. From dmesg: bananapim2plus:brcm:% dmesg |grep -i brcm [ 7.495253] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 7.497405] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.bin failed with error -2 [ 7.497440] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.bin [ 7.871128] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.txt faile…

First, I have installed latest Armbian 23.8 Bookworm CLI, boot works fine, I can login Then, I have installed wireguard. As a dependency, wireguard install linux-image-6.1.0-12-rt-armmp After reboot device is unavailable in network (orange LAN LED blinking while green does not, I assume ethternet broken with this kernel)

Hello everybody, I have installed the banana pi image Bananapi_Ubuntu_2.8_trusty_3.19.7. Almost everything works fine but I am missing a usb driver: https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx All my attempts of installing the driver failed: - when I try to use a ko-file from a different ubuntu version, I geht the error: "Exec format error" - when I try to compile the source from the link above, I get an "compiler too buggy" error - when I update the compiler and try to make the source, I get: make[2]: *** No rule to make target `arch/arm/tools/gen-mach-types', needed by `include/generated/mach-types.h'. Stop. make[1]: *** [arch…

Hi, if anybody can suggest if mentioned situation is OK? Thanks in advance. Originally all my OPI boards have been running on 624 MHz for DDR frequency. 2 days ago I decided to remove fans from My Orange Pi+ 2e and Orange Pi+ 2 (following suggestions from forum as fan is maybe not required). 1. Orange Pi+ 2e (this is running all my services which is: nextcloud, mail server, svn and web server to access mentioned) - originally with heasink and fan (as you can see downtime on Oct 14th - when I have removed fan and keep only heatsink). But something happened - with fan ddr frequency was always 624 MHz. Without fan some time after reboot it is increasi…

I don't know why fan doesn't work on my OPI +2E i even connected fan on gpio pin 4 and 6 . I'm noob but learning stuffs None of the gpio pins is working . Please tell me how to turn this 2 pin on for my fan. Please help me !!!

Hi there, I tried your images for orange pi, but doesnt work on orange pi mini 2. I tried ALL the images on the factory site, but somehow they placed copies of images for other models. (debian images are the same) Only image so far worked: lubuntu, but when i login, ssh session is killed. (as well root/orangepi as orangepi/orangepi) its driving me nuts to get this working. Any ideas? Great work btw!

I'm trying to use the WiFi module included with the Orange Pi PC Plus, when I try connect to a WiFi network (using just iwconfig and 'ifconfig wlan0 up') it doesn't connect, resulting in a kernel panic. [ 1029.575558] ------------[ cut here ]------------ [ 1029.591494] WARNING: at net/wireless/sme.c:531 cfg80211_connect_result+0x50/0x120() [ 1029.611113] Modules linked in: bnep bluetooth sunxi_cir pcf8591 bmp085 8189fs [last unloaded: scsi_wait_scan] [ 1029.611234] [<c0016a20>] (unwind_backtrace+0x0/0xe8) from [<c0687850>] (dump_stack+0x20/0x24) [ 1029.611283] [<c0687850>] (dump_stack+0x20/0x24) from [<c0029720>] (warn_slowpath_common+0x5c/0x7…

Hello everyone, Around July 2018 I was able to successfully build an Armbian image for NanoPi Duo using provided documentation: https://docs.armbian.com/Developer-Guide_Build-Preparation/ The reason I decided to build the image was that I needed it with legacy kernel 3.4.113. For some reason there were significant problems with using the mainline kernel with direwolf application which is an amateur radio APRS modem. The device hanged with mainline kernel after few hours of operation without any reason and this was not an overheat problem (temperatures below 50 degrees and a huge heatsink). I believe that it is some problem with audio driver for H2 wh…

I read few in the net about the ahci-driver of the A20-Board. I have a Cubietruck and I want to use a hdd with more than 2TB. Is it - theoretical or in principal possible? My HDD is found but only 2TB of it.

Hello, I have an Orange Pi PC with Armbian. I like the distribution very much, but I face a strange problem. After around 5 minutes of use I cannot longer open applications. When I switch to tty I see the following error: end_request: I/O error, dev mmcblk0, sector 3477952 mmcblk0: timed out sending r/w cmd command , card status 0xe00 mmcblk0: not retrying timeout At first I thought the problem was in the SD card, I scanned it - no bad sectors. Then I tried with the card from my Raspberry Pi which works perfectly with it. I copied the image with DD and I had the same error again. What could the problem be? A software one, or something in the power supply, becau…

hallo, for bananapim2 i can build jammy legacy and current, cli and xfce, on my pc-ubuntu-jammy. I just coppy bananapim2.eos to bananapim2.conf, removed box86 files while my pc-ubuntu-jammy seems have problems with build-script to download addition softaware from some git or ppa. Current-jammy goes off on boot on "starting kernel", but if i build with linux-sunxi-legacy.config renamed to linux-sunxi-current.config, boot is successful. On all builds i cannt becomme LAN over eth0, but wifi is ok. I can see eth0 and wlan on Networkmanager(cli too) and ifconfig. I tryed to disable all broadcom drivers i knew thru blacklisting, but wifi is working. Configuring NetworkManager a…

The guy just added a raspberry pi build to the server builds. I tested it and it works on Orange Pi Zero 512MB. There's a little lag, but I think it's playable. It's a really fun game, you should check it out: http://www.files.froemling.net/bombsquad/builds/

Update: checking download file, it seems that I downloaded Armbian_4.5_Cubieboard2_Debian_jessie_4.2.3.zip so it's not 4.81 no matter what the download pages said. I'm trying to install upstream kernel on Cubieboard 2 and kernel never starts. Attached is output from boot (I'm getting same on serial port). I did try different sdcard (to rule out problems with it) but I'm worried about ext4fs_devread read error and partition error. Is there something more that I can try? Legacy kernel works well, but I wasn't able to just upgrade kernel and u-boot on it, but that resulted in unbootable system -- which packages I have to install to migrate from legacy to upst…

I just reinstalled my Cubietruck with the Debian jessie, image from http://mirror.igorpecovnik.com/Cubietruck_Debian_4.1_jessie_3.4.108.zip. Only one core is available. What could I do so that the two cores are detected? For what it's worth, the bootloader briefly displays a "checksum error" message. Could it be that I'm still using the old bootloader from the previous installation? (It was Debian wheezy in summer 2014.) Thanks in advance for advice.

Hello, I'm interested in how to run the application calculated for a normal computer x86_64 (ubuntu), since the architecture arm is not supported, you need to do it as a bypass, in the application I post the script that I need to install. This is a radio bot. help me please sinusbot_installer.sh

Hello everyone, I'm trying to set up a system as musicjukebox supporting -MPD -USB Audio -WlanAP -7"Display With the Raspbian Image of banana-pi(dot)org with Kernel 3.3 lcd works but usb-sound not. With kernel 4.2 it is the other way around. The support is very bad in my opinion, so I'm looking somewhere else. Is armbian able to satisfy my needs? Or do I have to do much compiling/programming, which would be all new to me as a linux beginner... Regards Andre

Hi ! Ref : Olinuxino LIME2 4G with new 3.4.112 kernel When installing to NAND, on the console I see a lot of : PHY_PageRead : too much ecc err,bank 0 block 276,page 4 PHY_PageRead : too much ecc err,bank 0 block 276,page 18 and so on ... Sometimes the installation succeeded, sometimes not, but the system is often instable, and finally, fully unusable. I tried all the precompiled images, then I compiled myself, but the same problem ... Until now, I used 3.4.106 without problems Thanks for support ! Greetings ,

Hi, This is my first post and I want to say thank you to all the developers and contributors of this great eco system. I've build an image for odroid xu4 with the openmediavault script. This is really great because the software packages and kernel ist up to date and running like a charm. Then I tried to get my DVB card working but that is work in progress. The card is not supported by the 4.9 Kernel and the usual way is to compile the media_build package from hier: https://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers But with an cross compiled system as armbian i…

I'm running Armbian_5.20_Micro_Debian_jessie_3.4.112 on an Olimex A20 micro board. I find that opening serial port device `/dev/ttyS2` causes the system to crash. The board heartbeat LED either stops or blinks rapidly. The board itself is not pingable. I can reproduce this issue with a simple from the shell using: cat /dev/ttyS2 or from c code using: fd = open("/dev/ttyS2", O_RDWR | O_NOCTTY | O_NDELAY); `/dev/ttyS2` is linked to UART6. In the fex file, I have configured it like so: [uart_para6] uart_used = 1 uart_port = 6 uart_type = 2 uart_tx = port:PI12<3><default><default><default> uart_rx = port:PI13<3><default><defau…

Hi there, My question is to Orange Pi Zero owners. I've read is has DDR3 RAM shared with GPU. What is a minimum value of GPU memory? I'm looking for headless setup so it would be good to know how much memory can be used by OS. Thank you in advance.

hi all, I've been running into an issue where the kernel starts throwing error messages (https://pastebin.com/bmPJPeq0), the board becomes very slow and the cpu load goes to 11 and stays there. This seems to happen when I change the CPU freq using armbian-config to anything lower than 528MHz. Any ideas how I could resolve this?

Hi, I would like to share an issue concerning the OPI Zero 2+ with the camera module. I was not able to work with it and I got usual error : [ISP] isp platform_id = 5! [CSI_ERR][GC2035]sensor_read err at sensor_detect! [CSI_ERR][GC2035]chip found is not an target chip. I finally found that the FEX was incorrect. On line 384, the port definition was wrong and should be PA08 : vip_dev0_power_en = port:PA08<1><default><default><default> Then the camera is recognized : [ 8652.370168] [ISP] isp platform_id = 5! [ 8652.447812] [CSI][GC2035]V4L2_IDENT_SENSOR=2035[CSI][GC2035]disalbe oe! And worked properly with f…

First, thanks to the developers for creating a system that works very well, much better than the official distros. The question is if you could add to repositories Amule and their add-ons: Amuled, amule common, amule-utils and Gnome-support. Thank you.

Hi everbody, I am trying to get my GPS dongle connected to my USB but it does not work. The idea is, to have Opencpn installed and GPS connected to it. My system: Orange Pi 1 ARMBIAN 5.59 stable Debian GNU/Linux 9 (stretch) 4.14.65-sunxi GPSD installed My ifonfig: wlx20e816009606: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.50 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fd9b:3717:53b3::3e2 prefixlen 128 scopeid 0x0<global> inet6 fd9b:3717:53b3:0:7f5f:c66e:cfc3:ca21 prefixlen 64 scopeid 0x0<global> inet6 fe80::db2f:fae5:558e:15b prefixlen 64 scopeid 0x20&lt…

Hi everybody, I have an Orange Pi One run Armbian Server image. I want to write an GUI application by QT on the my computer and compile/run on Orange Pi One. I read and follow some tutorials, but not success. Are you suggestions for me? Many Thanks!

Hi i have orange pi lite board, i run :ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i on this boards and works fine, but when I turn on the card there is no text in the hdmi output until it finishes loading the operating system, how i can configure the armbian to see the boot text?? i can see the boot text by USART port, but i want to configure by HDMI monitor. Best Regards Nelson

@dear Igior and others My R1 fw1 run fine past 2 month with the 3.19.3. now its time to move to 4.0.x Igor - many thanks for KERNEL_CONFIGURE at your scripting implementing . This shortcut my work with automated rebuild kernel an bit -- but not fully. I have the need to been able to push my own kernel .config into your https://github.com/igorpecovnik/lib in an automated way. But how about to push an custom .config into that? welll ... My suggestion are here top add i.e at your compile.sh : KERNEL_CUSTOM_CONFIG="/path/file" if file env set , use it instead from default patched kernel .config How you think about this Idea ?