Allwinner sunxi

Hi My cubie2 with a 2.5" HDD has exception Emask 0x10 SAct 0x80000 SErr 0x90300 action 0xe frozen [182296.803589] ata1.00: irq_stat 0x08400000, interface fatal error, PHY RDY changed [182296.803605] ata1: SError: { UnrecovData Persist PHYRdyChg 10B8B } [182296.803624] ata1.00: failed command: READ FPDMA QUEUED errors sometimes, which causes shutdown, spin up for HDD, with a big click sound, and it's not good for it. So i would try if it happens when the sata link is set to slower. But how can i do that?

I've upgrade armbian to 5.31, now I have 2 freeze in 2 days Here my log http://sprunge.us/gUeO

root@orangepipcplus:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 1002 0 0 eth0 0.0.0.0 192.168.30.1 0.0.0.0 UG 1024 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.30.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

i'm trying to make suspend on lid close work. i saw in this thread that some people are aware that there's a problem. i'd prefer to achieve this from within xfce4-power-manager. here's the thing: 1. using the normal xfce desktop * for "when laptop lid is closed", only 'lock screen' and 'switch off diplay' are available * "System sleep mode" is completely grayed out, as well as security 'lock screen when system is going to sleep' * the 'Ask' option is available only for "Buttons". Choosing it, then choosing "Suspend" from the dialog, causes the ui to hang (desktop darkened), but after a minute i can 'escape' …

As title says, i am try to get the flash thing going on the UART0 on the OPI Zero (the debug ports i guess). But i got no luck, anyone has any experience with this? Thanks:)

I've been trying to change the I2C clock frequency on a NanoPi Duo doing the following: cd /boot/dtb sudo cp sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dtb.old sudo dtc -I dtb -O dts -o sun8i-h2-plus-nanopi-duo.dts sun8i-h2-plus-nanopi-duo.dtb sudo nano sun8i-h2-plus-nanopi-duo.dts in i2c@01f02400 section change clock-frequency = <0x186a0> to clock-frequency = <0x30d40> (200 KHz) sudo dtc -I dts -O dtb -o sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dts reboot Looking in armbianEnv.txt I have overlay_prefix=sun8i-h3 and cat /proc/device-tree/model shows FriendlyARM NanoPi DUO. The issue is that no mat…

Hy I tried to play around with the GPIOs and found some nice threads here however I don't get past the modprobe gpio command. I get this error modprobe: FATAL: Module gpio not found in directory /lib/modules/4.14.29-sunxi64 Does my kernel build has no GPIO library inside? Linux 4.14.29-sunxi64 #64 SMP Sat Mar 24 11:13:51 CET 2018 aarch64 GNU/Linux Andy

I've tried both revisions (Bionic and Stretch) for this board located at: https://www.armbian.com/orange-pi-pc/ Both have the same issue. When I boot from sd card, run armbian-config, and attempt to transfer armbian OS to emmc I get an error 'no target'. I know that there is indeed built 8GB flash, because when I pull the sdcard, and power the board it boots into the pre-configured android OS. Here is a picture I took of the board: https://photos.app.goo.gl/5ELPTTnPbZXAybhe9 Any advise would be helpful. Thank You.

My PineH64, as well as OrangePI one plus (H6) were working fine using 4.18.rc7-bionic till I have tried apt upgrade I'm getting the following error on both. Any ideas? Thank you vm Starting kernel ... [ 2.104055] Internal error: Oops: 96000004 [#1] SMP [ 2.108938] Modules linked in: [ 2.111997] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.11-sunxi64 #5.67.181221 [ 2.119819] Hardware name: Pine H64 (DT) [ 2.123750] Workqueue: events deferred_probe_work_func [ 2.128887] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.133679] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.138121] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.142560] s…

Hello, I wonder how to use built in microphone on Orange Pi one +? root@orangepioneplus:~# arecord -l arecord: device_list:272: no soundcards found... Thanks

I am very confused. I don't know where the problem is. Have you ever encountered the same problem? Kernel 4.19.80-sunxi Debian Stretch armbian version 5.98 Orange Pi R1 No third-party hardware was added. Pure R1 bare board Start error message： [ OK ] Started LSB: set CPUFreq kernel parameters. [ 8.670214] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 8.681560] pgd = 95d3822c [ 8.684287] [00000000] *pgd=00000000 [ 8.687884] Internal error: Oops: 805 [#1] SMP THUMB2 [ 8.692942] Modules linked in: binfmt_misc 8189es zstd zram lima sun8i_codec_analog snd_soc_simple_card sun8i_adda_pr…

I remember that the maximum frequency was 1296Mhz back with Xenial, with kernel 3.x. It even says here Heat is not a problem since i have a large heatsink and temperature controlled fan, i was just curious about why the max frequency was bumped to 1368Mhz on the newer builds. What's the rationale behind it?

Hi, Just as my last post. I want to know if it is possible to wakeup opi3 after I switch its state to "mem" or "disk" using gpio on CON12. I have doing some reasch but I don't know if it is right: PL/PM port can be used as wakeup source. PF/G/H/L/M port support interrupt event. PC/D didn't support interrupt. But when I try to write a device tree file, but it just report some error with error code -22. My device three is like this: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h6"; /* * This fragment is needed only for the internal pull-up activation, * external pull-up resistor is highly recommended if using long wires */…

Hi. I've always had problem with the composite output (cutted edges) so i gave a try to the latest release. Unfortunatly the video does not show up at all. Anyone still using the old Opi0?

Hi, i am trying to get the Respeaker 2 Mic Pi hat working on a Banana Pi Zero M2. The HAT uses the WM8960 codec and generates its own I2S MCLK. After some trouble i got the i2c interface working and i2cdetect shows a device at address 0x1a which is correct. But i can not get the I2S interface working. I have added a user overlay with the following .dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { #address-cells = <0>; #size-cells = <0>; s…

I have orange pi zero board ..i searched a lot for changing boot splash screen ( currently "armbian universal operating system" which is enabled by adding bootlogo=true in armbianEnv.txt ) I have tried Plymouth it is not working After searching lot i knew about if we can replace bootsplash.armbian , it can help because then neither we need to change uboot packages nor we have to add quiet splash like words etc in armbianEnv.txt. https://github.com/armbian/build/tree/master/packages/blobs/splash. With help of this bootsplash-packer Can anyone list me some steps ( in short ) How to run this script and create…

hey, it is nearly everything said in the title. I want to use my cubietruck for playing streamed videos on my beamer. I don'T want to take my pc to the living room everytime i want to watch tv on my beamer, so i hope, there is a way to get the cubietruck working with vlc mediaplayer. Any tipps?

Hello, I have been looking for days without finding an answer, so here goes. I want to know if there is a way of turning on the banana pi, without using the onboard switch. Because the Banana pi r1 doesn't power on automatically when powered by the battery connector. And i don't want to solder wires on the pwr button, but i would also like to avoid using the usb connections because of the lower power throughput. Thank you in advance for the information.

Hm.. I'll write to you what I have done. Please tell me what's wrong. I have a cubietruck, and I downloaded this one, Legacy Jessie(http://mirror.igorpecovnik.com/Armbian_5.00_Cubietruck_Debian_jessie_3.4.110.zip), and installed it. Install was successful, and worked good. I tried to use nand and SD, and SD only. There were no differences. The result that I want to tell you below, is the same on both cases. ......................... After OS install, I followed this instruction, and I installed several packages. Instruction : wget -q -O - http://upgrade.armbian.com | bash Packages : NFS server Samba server Deluge Daemon(server) I have a 3TB sata disk …

comes to adding 131068 swap on /var/swap and further loading is not How to fix it? tried a USB flash drive to the new record, it is still the same, a reboot is not helping

Hey Community! I installed Armbian Jessie without any problem to SD Card. HDMI was the default screen output, and I changed to VGA with the help of this topic: http://forum.armbian.com/index.php/topic/445-debian-images-cubietruck-vga-output-problem/ The next boot went fine, VGA works. But, after the system upgrade-update, after the reboot the screen is HDMI again. I checked the card's file system with NAND ubuntu, the output order (the 4 row) is 4-4-4-4. So, I can't understand. The VGA monitor is fine, working in the next few phase before the kernel starts, but after that: just blinking. If I connect the Samsung HDTV, the desktop present there.... Thanks for t…

Hi i am using Orangepiplus and armbian 5.20 debian jessise. but i have problem. somtime it's stopped Point is => started LSB: set CPUFreq kernel parameters or => starting LSB: set CPUFreq kernel parameters, so i adjust boot clock using /boot/script.fex => boot_clock : 1080 -> 1180 and => boot_clock : 1080 -> 980 but it's failed. help me please. (i try to reboot command, 100sec (repeat))

I bough an Orange Pi PC set 9 which came with a camera ( https://www.aliexpress.com/item/Orange-Pi-PC-set-9-Pi-PC-and-Camera-with-wide-angle-lens-not-for-raspberry/32662572137.html?spm=2114.13010608.0.0.dIEdek ) After setting up armbian running etc. how do I do something with the camera (ie to see it works)? I have used raspberry and there I just type "raspistill -d" and a demo pops up. How do I do something like that? After browsing around I found that "modprobe gc2035" is along those lines but I only get "command not found". Doing a linux find does not find "modprobe". I reckon I have to install something else but what?

Hi all and many thanks to armbian team - it is a great distro. I installed armbian to my orange pi pc (just pc, not pc+) and it works. TV out works too. But no one of my usb wi-fi adapters are supported by default kernel 3.4. This is why I go to "kernel" tab at page https://www.armbian.com/orange-pi-pc/and follow instructions to switch to development kernel. Also I follow instruction at "Nighty releases" tab in order to get the newest versions of software. After installing new kernel I edit symlik /boot/script.bin to point to "bin/orangepipc.bin" instead of default "bin/orangepipcplus.bin" and reboot. Orange pi boots successfully and I can log in via ssh, but tv sign…

Like whaaaaaa... Okay, so long and frustrating story short, I have been having inexplicable stability issues on my Banana Pro. I have blamed the SD card, the power supply, the micro USB cable, but none of those leads seemed to actually lead anywhere. I connected up a Fluke multimeter to the SATA power output, set to peak min mode, to see if I get any undervolting... Nope, no problem there. I ran stress tests on my sd card on my computer - it was PERFECT. I was completely stumped... Until, after getting an Anker charging cable, and having a really good run with the new Armbian release - the system had been working for an hour without glitches, apt-get worked, I hav…

Hey all, Sorry for the noob question, I posted this in another topic but it hasn't seen any action so I thought I would make a post. I have an Orange Pi PC, using the RetroOrangePi build which is based on Armbian. I'm having overscan issues on my 720p TV. I checked the options on the PC, there's no way to fix it there. They figured it out in this topic here (where I initially asked this question): The solution is to add code to u-boot in order to solve the overscan, or edit boot.cmd. My question is, will using u-boot be the best solution, or is it better to edit boot.cmd? Do I simply create a boot.cmd in something like note…

I'm going to use MIPI DSI LCD with OrangePi Win. In default configuration MIPI DSI is disabled. I activated Samsung DSI panel in kernel configurator. But it seems it always compiles default configuration. I don't see mipi dsi in dmesg. And image size is always exactly same, doesn't matter make I change in configurator or not. So my question how to compile whole image with MIPI DSI support? Thank in advance!

Hi all, can some kind soul tell me if this update will break my cubieboard installation? (I know that cubieboard a10 is no longer supported, nevertheless maybe someone can tell me after 5 seconds of thinking "yes" or "no" :)). XXXXX@cubieboard:/etc/apt/apt.conf.d$ apt-get -s -t stretch install dnsmasq NOTE: This is only a simulation! apt-get needs root privileges for real execution. Keep also in mind that locking is deactivated, so don't depend on the relevance to the real current situation! Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be instal…

Hi, I am trying to interface I/O expander MCP23017 to Nano Pi Neo2(Hardware specs:1 GB RAM, Gigabit Ethernet . Software specs: Debian Buster with Armbian Linux 4.19.59-sunxi64 ) . The issue I am having is I am not able to see the device when I run sudo i2cdetect -y 0 . I have enabled i2c overlays in /boot/armbian.txt . I am using 10 K Ohm pull-ups on SDA and SCK . I get no activity while running i2cdetect on the oscilloscope on SCK and SDA lines . Is this an issue with the kernel ?

Hi, trying to install a char driver without any driver framework. The only thing I can not install is getting the Interrupt through to the interrupt servce routine err = request_irq(irq, handler, // IRQF_TRIGGER_RISING, IRQF_TRIGGER_HIGH, "can4linux", &can_minors[minor]); irq is the Interrupt number of the CAN controller, it is fixed in the A20 to 58. I do get no error messages, but the isr is not called. What I am missing? Greetings Heinz By the way, it worked an Bananian 3.x

Hi, I've got a pair of OrangePi 3 LTS boards running the CLI only install of Debian Bullseye with a kernel of 5.15.89-sunxi64 and all the latest updates applied. But when I run the 'top' command, I always see a load of 1.0 or higher. Even when the system is completely idle. I'm running the system of the eMMC, not SDcards. I realize that this is really more of a cosmetic issue, but I was hoping someone had a suggestion on how to fix it. The system is mostly idle, it's a test box or remote management system, so it's not really critical, and the load doesn't go high anyway. Cheers, John

Hello, sorry for my very bad english. I have installd the desktopimage for the bananapi m1. It works. But same programms does work because the autmatic login user is root. So exaile, chromium-browser does start. Synatipc starts from the gui after starting the AT-bus programm (see menu starting programms) Tunar needs to install the gvfs-backend, then you can see the computers in the network. To change the language in the gui you need to install the language-pack-de (for german). I have also a cubitruck and thin this problems also in the image for the cubietruck. The first problems can solved when the automic user is not root. The other w…

Before installing this Armbian legacy kernel (3.4.109), I was using a Bananian-based image with OpenMediaVault (the so called BanaNAS image) and was getting regular 30MB/s transfer rates to my Samba shared hard drives (USB and SATA). My PC and Banana are connected through a gigabit switch, and working at 1Gbps. After installing and configuring the new Armbian image, I notice my transfer rates were now around ~23MB/s which was odd. After trying to change some smb.conf parameters and getting nowhere, I decided to test just the network performance by setting up a simple web server on my PC and doing a wget -O /dev/null http://<my PC-IP>/test.zip of 3Gb. The values …

Hello, I just upgraded my system from 3.4.110 to the kernel 4.4.1 (Debian7) by Igor's script (Thanks Igor). But I have noticed that in this version of the kernel is no longer possible to set the green light to the disk activity. Is there a way, patch or other to fix it? Thanks Fred

Hi, I have a beelink X2 and did: apt-get update apt-get upgrade apt-get install -f apt-get update apt-get autoremove -y I think i have version 5.20. If i look at: cat /etc/*-release # PLEASE DO NOT EDIT THIS FILE BOARD=beelinkx2 BOARD_NAME="Beelink X2" VERSION=5.20 LINUXFAMILY=sun8i BRANCH=default ARCH=arm PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" So i think i have version 20 But if i do an: cat /proc/version Linux version 3.4.112-sun8i (root@xenial) (gcc…

Hi, Board: nanopi neo, running xenial ubuntu server from: http://www.armbian.com/donate/?f=Armbian_5.20_Nanopineo_Ubuntu_xenial_3.4.112.7z I am trying to enable the hostapd for nanopi neo, on Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter The default drivers cocam@nanopineo:~$ lsmod Module Size Used by rtl8192cu 61143 0 rtlwifi 45784 1 rtl8192cu rtl8192c_common 33420 1 rtl8192cu snd_usb_audio 80300 0 mac80211 358429 3 lrtlwifi,rtl8192c_common,rtl8192cu came with 3.4.112-sun8i looks ok and my wlan0 is AP-advertised, wlan0 Link encap:Ethernet HWaddr ec:08:6b:…

Hi, I just installed ARMBian on my Banana Pi M2+ (BPi-M2+) and think to do the same on my router Banana Pi R1 (BPi-R1). As the WiringPi is created for GPIOs from Raspberry Pi, I presume there are perhaps not the same on those Banana Pi boards. But I discovered there are many Wiring libraries for this GPIO use on the BPi. Does somebody give back its knowledge to know which Wiring library is the best for those two Banana Pi boards ? - WiringBP - WiringOP - MikuPi I want to use them for reading Temperature and Humidity (DHT22) and a sonar sensor (HC-SR04). And further with a NFC rader. Sincerely thanks for your help.

I am trying to control a relay board on OPI PC plus - armbian. I have used "orangepi_PC_gpio_pyH3" module in python before to control leds, buttons and an 16x2 LCD. This is the relay. To control the Relay module i connected VCC to 5V, GND to ground and IN to PIN 35 (Which is PA10 on my board). and used the code below to open or close the relay just to test but no luck. The code does not return any errors, it runs and finishes but no activity on relay. Both leds (Red and Green) on relay are on when connected. Any help would be appriciated.

I under stand OPi-GPIO is a drop-in replacement library for RPi.GPIO for the Orange Pi Zero. It added a new GPIO pin definition GPIO.SUNXI. However, I cannot find its definition. Can somebody let me know or point me to a link where it is defined? Thanks.

My Cubieboard 2 absolutely refuses to boot from microSD. It will boot into Android from flash when there is no microSD card inserted, but with a card in, it just produces a single red LED and no video output. Eventually it will respond by flashing green and powering down when the power button is depressed, so I feel like it's getting somewhere, but those are the only signs of life. I don't know how to look at serial output from this machine. I've tried two different power supplies, and two different monitors because one had I think been dodgy with this machine before. Same problem on all permutations. I also tested the SD card with F3 and wrote it with Etcher, and I've us…

I recently ordered 3 A20-OLinuXino-LIME2-e16GB devices (with 16GB eMMC) and received rev. K boards. Unfortunately, I have troubles with both "official" Olimex eMMC rel 16 image and latest (as of last week) Armbian Stretch images. Both images booted fine from SD card (also tried multiple SD cards, one of them bought from Olimex ) and I was able to run the emmc.sh / nand-sata-install scripts fine. Now the troubles started as I turned off the device, removed the sd-card and tried to boot from eMMC. All 3 boards had entered FEL mode. From fel mode I was able to use the `sunxi-fel` utility and push the uboot fine... Initially I was able to g…

Hi All, I am working on project using Qt(IDE), C++(language) and opencv libraries. The board I am using is Olimex Olinux A64. In the project I have a GUI that displays the input from a camera and has various status indicator labels. These labels indicate various states the system is in at any particular instance of time. I load different images in the labels to indicate different states. As of now the trigger to change the image of a label comes from soft buttons written in c++ using the Qt buttons layout. I am trying to find a way to control the change of images in the labels using hardware buttons that are connected to the GPIOs of the A64 board. Cou…

Hi, I try to connect Orangepi lite to SIM800l module. I don't have any response on AT commands. I checked the module with Arduino and it works. So I connected Arduino and Orangepi and I can send messages from Arduino to Orangepi, but I can't get any message from Orangepi to Arduino. 1, On Orangepi I allowed UART3 via editing /boot/script.bin [uart3] uart_used = 1 uart_port = 3 uart_type = 4 uart_tx = port:PA13<3><1><default><default> uart_rx = port:PA14<3><1><default><default> uart_rts = port:PA15<3><1><default><default> uart_cts = port:PA16<3><1><default><defau…

Hi, I could not able to download and install any packages, following is the eg. i was trying to install dkms package sudo apt install dkms Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package dkms in addtion apt update is running partial , throwing errors as below sudo apt update Get:2 http://ports.ubuntu.com bionic InRelease [242 kB] Hit:3 http://repository.olimex.com bionic InRelease Get:2 http://ports.ubuntu.com bionic InRelease [242 kB] Err:1 https://apt.armbian.com bionic InRelease Could not wait for server fd - select (11: Resour…

Hello After spending hours of trying to create an older DEV kernel (5.1.21) here are the following steps in order that it will work. I will describle here about the 5.1.21 kernel but I think it can work for any kernel. 1. create lib.config file under build/userpatches with the following: KERNELBRANCH='branch:orange-pi-5.1' 2. And this is what create the magic: download the Armbian files that matches that distribution and replace all the files in the build directory: for example I have downloaded from here - This link is the build version from the branch of the 5.1.: https://github.com/FireflyTeam/armbian-build/tree/e…

Hello, for my BananaPi I recently downloaded "Armbian_21.05.1_Bananapi_buster_current_5.10.34.img" and did not get the on-board CAN controller working with this image. I found out that in sun7i-a20-bananapi.dtb (uses sun7i-a20.dtsi) the group name for the CAN pins PH20 and PH21 has changed from "can0_pins_a" to "can_ph_pins" but in the sun7i-a20-can overlay this change had not been done accordingly, and the DT merging failed. So changing "sun7i-a20-can.dts" to: /dts-v1/; /plugin/; / { compatible = "allwinner,sun7i-a20"; fragment@0 { target = <&can0>; __overlay__ { pinctrl-names = "default"; pinctrl-0 = <&can_…

Why do I keep getting negative CPU temperature readings? pi@orangepizero:~/klipper_config/config$ armbianmonitor -m Running unprivileged. CPU frequency will not be displayed. Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 21:01:44: --- 0.18 4% 1% 2% 0% 0% 0% -3280°C 0/4 21:01:49: --- 0.17 2% 0% 1% 0% 0% 0% -2433°C 0/4 21:01:54: --- 0.15 2% 0% 1% 0% 0% 0% -2675°C 0/4 21:02:00: --- 0.14 4% 1% 2% 0% 0% 0% -2796°C 0/4 21:02:05: --- 0.13 2% 0% 1% 0% 0% 0% -2312°C 0/4 21:02:10: --- 0.12 3% 1% 2% 0% 0% 0% …

I have an issue with the latest releases since Yammy on a Orange Pi Zero LTS. Reboot is not working (system shuts, but not starting again)

I just reinstalled my Cubietruck with the Debian jessie, image from http://mirror.igorpecovnik.com/Cubietruck_Debian_4.1_jessie_3.4.108.zip. Only one core is available. What could I do so that the two cores are detected? For what it's worth, the bootloader briefly displays a "checksum error" message. Could it be that I'm still using the old bootloader from the previous installation? (It was Debian wheezy in summer 2014.) Thanks in advance for advice.

I have a "Banana PRO" One USB disk, 2TB with three partitions in ext4, the first partition is mounted (hdb1), the other two are not mounted. One USB disk, 4TB with a single ext4 partition mounted (hdc1). One SATA SSD disk with a single ext4 partition unmounted (hda1). Several aesthetic considerations: After the upgrade, reboot and login, the welcome screen and 100% battery!!! Hurrah!!! It seems that the MMC is 9% occupancy and ... oh! my hdb disk has only one partition? ah no, only reads hdb1. And the other two disks? I have two mounted partitions but only shows one. Turn off the system with the poweroff order and boot from the power button again, the battery is down to…

The built-in WIFI module doesn't switch to monitor mode. This makes me looking for rebuilding the module from the Git repository: https://github.com/rdm-dev/rtl8189ES_linux/tree/52ee6388111fbaf990ec60e93b086cafa6cc373a I am stuck with the following error: *** No rule to make target 'arch/arm/tools/gen-mach-types', needed by 'include/generated/mach-types.h'. What is necessary to rebuild and replace the module with a new one? Here is what was done so far: root@orangepiplus:/usr/src/rtl8189ES_linux# uname -a Linux orangepiplus 3.4.110-sun8i #18 SMP PREEMPT Tue Mar 8 20:03:32 CET 2016 armv7l GNU/Linux root@orangepiplus:/usr/src/rtl8189ES_linux# dmesg |grep 8189 [ 3.…

Hi, Nanopi M1 is so similar to Orange Pi One that you can use the amazing work provided by jernejsk and run Openelec using the VPU of the H3. Here are the links : * Main page * prebuilt images list * Github project * The issue I've opened I'm using the embedded IR Sensor with my remote (that was the toughest part) and the only modification I made was to change to cpufreq governor from performance to conservative but if you use the latest image you shouldn't have to do that. Well so far so good. I'm using a little heat sink and the cpu temperature is between 60°C and 80°C depending of the video I'm playing.

Hi, I'm trying to make a hotspot with the beelink x2. I have some problems with resume after suspend. So i have a question about the beelink x2. Does anybody know if it is possible to start the beelink after a shutdown with the power-button. If i want to restart it, i have to re-insert the power-cord and the beelink will boot. Button does nothing. Thanks. Erik

Hello, I'm running Armbian wiith Kernel 3.4.112-sun8i on an Orange PI PC. In addition I compiled WiringOP patched for Orange PI to check GPIO. I have connected a transmitter which communicates using SPI and an additional GPIO PIN to send interrupts. The device is not working yet and I try to find out the problem. It works fine with an Rasp. For example, I'm a little bit confused about the following: /sys/class/gpio/gpio5/direction shows me "in" "gpio readall" shows me: | 18 | 1 | OUT | GPIO.5 | 5 | 24 | Of course, I could change the mode using the gpio command, but I would expect, that both values match? Could it be too, that the inter…

Hello everyone, First of all, sorry for my bad English. Quick description of my problem: I recently buy three Orange Pi Plus 2E with official case and official AC adapter. On this three cards I want to use Armbian, I use the last version of Armbianfound here: https://www.armbian.com/orange-pi-plus-2e/ Write on SD card with Win32DiskImager. For information, I use a Samsung EVO 16G SD Card, same HDMI cable, same screen and official A/C adapter. For two cards, no problem, boot on Armbian on SD card and install on emmc in 10 minutes, but the last one have some problem... The last card won't boot on SD card with Armbian: black …

Dear All, I try to use the UART3 on my Orange Pi mini but it just won't work. I put a jumper on Pin 8 and pin 10 on the header. Also give read/write premmission to all users. Based on this UART3 is /dev/ttyS2 [ 0.000000] console [tty1] enabled [ 0.954713] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A [ 0.985810] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A [ 1.016890] sunxi-uart.3: ttyS2 at MMIO 0x1c28c00 (irq = 36) is a U6_16550A [ 1.047968] sunxi-uart.7: ttyS3 at MMIO 0x1c29c00 (irq = 52) is a U6_16550A [ 6.014770] systemd[1]: Expecting device dev-ttySAC2.device... [ 6.681738] systemd[…

Hi All Please can someone assist me. I'm at my wits end here. I have an Orange Pi Lite running Armbian 5.30 desktop edition. I want to rotate the display 90deg. I have had no luck with xrandr as it lists the display as 'default' and not a specific output and this seems to cause a problem. The option to rotate the display is also not available in the display manager. Thanks in advance.

Hello, i reinstalled the latest version of armbian with jessie on the cubietruck, on UART0 (ttys0) i plugged in a razberry but since the last version it is not recognized and does not turn on. Is it possible that UART0 is inactive? I have found on this forum for OrangePi with script.bin but not for cubietruck Where is script.bin ? thank you

I've updated to the latest kernel code, rebuilt and I I can now see /dev/video when I call "modprobe ov5640; modprobe vfe_v4l2" after booting into the nanopi. However, when I run the following ffmpeg -re -i /dev/video0 -c:v libx265 -preset ultrafast -x265-params crf=23 -f h264 ./out.mp4 I get the following error error [video4linux2,v4l2 @ 0x1a9a7f0] Dequeued v4l2 buffer contains 40960 bytes, but 38016 were expected. Flags: 0x00000001. The video format is yuv420p, 176x144, so it should be 176*144*1.5 bytes = 38016bytes. However the buffer seems to be slightly larger. I have written a few small c program…

We want to merge eMMC/non eMMC images and in theory, it should work. eMMC version works on my Lime2 but just to make sure I need some feedback from Micro with and without eMMC, especially most recent ones. Lime2 with or without eMMC https://dl.armbian.com/lime2/Debian_stretch_next_nightly.7z Micro with or without eMMC https://dl.armbian.com/micro/Debian_stretch_next_nightly.7z Thank you.

I've been having a rather odd issue with an entirely pink screen upon cold boot. I tried with Raspbian and it didn't occur there. This has actually prevented me from using the device at all now. When I first set it up, I was able to Ctrl C the setup stuff and type in reboot. When it rebooted, I was able to use it again. However, last night the Wifi completely died. I tried everything to revive it but it kept asking for the password repeatedly. Tried different networks, no luck. Figured power cycling might help. Bad idea. Now I can't SSH in to type in reboot, and I'm now permanently stuck on a pink screen. Doesn't matter if …

Hello. I install the 5.35 Version on a OrangePiPc+, all run in good condition. I upgrade to the 5.38 without problem (kernel 3.x) I upgrade the kernel to 4.x, so long as i didn't reboot, all is in function (with Ubuntu) and my USB Tevii 662 is recognized (and run with TVHeadend). After reboot, no Ethernet and no USB, no possibility to login. I tried all versions with kernel 4.x, even desktop, no function. Anyone has a idea, how it will be run??? Thank's for any idea. P.S. OrangePI PC Plus, 1 GB RAM, 8 GB SSD-OnChip, Tevii S662 S2 USB, TVHeadend.

Hi there, I am new here, and new to Armbian I have a Orange Pi Plus2 and I am trying to make a project to present Spotify as an iPod over USB, so that it can be used in vehicles / docks that support iPod connectivity via USB Some of this work has already been done here on the iPod USB gadget driver side https://github.com/oandrew/ipod-gadget Using the standard premade armbian builds I cannot compile the source code as the headers are missing. Therefore I compiled Armbian from source using INSTALL-HEADERS=yes, mainline Jessie. As there is no option for the Orange Pi Plus2 board, I used the Orange Pi plus config instead. …

Hi Everyone After several weeks (maybe months) seeking for a solution for my problem I decide to post it here and hope to get a fix for it. At first I still run an Cubietruck with Armbian (everytime the latest Version) with just a few services (Pi-Hole, RPi-Monitor) and for future use Apache, MariaDB and PHPmyadmin (just installed and running, but with no content). Now to the problem itself: The Cubietruck runs approximatly 6 to 10 days and then it's get stuck. Only a reset solve the problem for the next 6 to 10 days. On every crash I checked the syslog and it always show the following lines as latest entries: Jun 29 15:17:28 localhost systemd[1]: St…

Hello, does anybody found a working WiringPi version for the Orange PI Zero+ H5?

Today I re-installed my Cubietruck as it was really outdated. It had: Linux cubietruck 3.4.105-cubieboard #8 SMP PREEMPT Fri Jan 23 06:11:42 EST 2015 armv7l GNU/Linux still running without issues. I reformatted the SD card with: ARMBIAN 5.65 stable Debian GNU/Linux 9 (stretch) 4.14.78-sunxi Configured everything and now I want to move the data to my SSD. (just as I had before) However dmesg shows me: cubietruck ata1: SATA link down (SStatus 0 SControl 300) What did i miss??

Ethernet was working fine for me, up until I rebooted the board. The LEDs on the ethernet port blink briefly during boot, but once booted they are off, and the board does not have an IP address. Via serial console I undid the change I made prior to the fateful reboot (adding 'overlays=uart1' to '/boot/armbianEnv.txt') and rebooted again, but to no avail. Having searched for the issue, I also confirmed that my power supply is sufficient; running 'stress -c 2 -m 2', and measuring across pins 2 (5V) and 6 (GND) of the 40-pin header, I get 5.05V. As I don't have a network connection, I did not run 'sudo armbianmonitor -u', but I gathered the following …

Ok, so, first of all, I am a complete noob. I bought Banana Pi thinking that it is similar to Raspberry Pi's architecture but it's obviously not. I bought a 240x240 Waveshare 1.3 inch hat and I was wondering how to get it working on my Banana Pi Zero (H2+). On Raspberry Pi I can use Juj's fbcp-ili9341 driver but it's probably not compatible with Armbian, right? How do I go about it? Also, it would be nice to know how to detect buttons (that are on the hat) and convert them to key strokes. Thanks!

Gentlemen, I've spend time looking for the GPIO pinout for the Orange Pi Win I am using with Armbian. Specifically I would like to use SDA and SCL. Does Orange Pi publish some information on this subject? Thanks in advance for your information.

Hi, I've recently got a ZeroPi from FriendlyElec and I immediately installed Armbian Buster, so far is working great except for a minor issue with the Gigabit ethernet. I'm planning to use it with Wireguard as server so I've made some performance checks first to test the actual network speed with iperf3. What I discovered surprised me, the network throughput in upload from the ZeroPi is fine (900 to 950 Mbps) but the download seems to be limited to ~380 Mbps. ------------------------------------------------------- # UPLOAD TEST (ZEROPI ---> HOST) # $ iperf3 -c XX.XX.XX.XX ------------------------------------------------------- [ ID] Interval …

I don’t own banana pi but I’m thinking of buying it for the project we’re going to do. I have raspberry pi zero but mediapipe is not working. Can I install this library on m2 zero? I would be glad if you help. Thank you.

I'm on Armbian 22.11.1 Jammy / 22.04.1 LTS, kernel 5.15.80-sunxi. Orange Pi Zero LTS. I have the issue that using all available audio players, the first half a second or so of mp3s are cut off randomly. Meaning that sometimes the beginning plays correctly, sometimes part of the beginning is cut off. Repeadetly running the player sometimes works sometimes cuts off the audio. I have tried play, ffplay, both have this issue. The speaker is a small amlfier module, the LINEOUTL output is connected to it, but the right is the same. Any ideas where to look? This is driving me insane. Thanks! I have attached a test mp3, w…

Hello, I'm newbie with linux and the Cubietruck. What is the difference between the version Wheesy, Jessy and Trusty ? Thanks François

Hi. I'm a new user. I have a Banana PI M1+, that is connected to a monitor with maximum resolution of 1280x1024 and with only DVI port. I'm using Armbian_4.5_Bananapi_Debian_jessie_3.4.109, and I installed XFCE using tasksel. If I leave it without any user interaction, the monitor goes to sleep, and I'm not able to wake it up anymore. But it works, because I'm able to connect to it using putty from another computer. So I tried to install Armbian_4.5_Bananapi_Debian_jessie_3.4.109, but I have the same problem. I tried also to disable "Switch Off After" in the Display section of power management without success. Can someone help me please?

Hi everyone, I bought an Orange Pi oneas a cheap replacement for the unobtainable Raspberry Pi Zero for a little Emulation project. Right now I don't know if it was the right decision:) I wanted to add a waveshare 3.5" display to the orange pi, but I don't even get there. I downloaded the armbian distribution v5.10 legacy Jessy desktop. After the start of the desktop, icons, the taskbar and open windows disappear at random, icons return but the taskbar does not, The desktop is unusable. A similar problem happens in the console, I don't see the cursor where I'm typing. On the command line, thats acceptable but using an editor like nano I have no idea where I am. …

Hi Forum, My CT with "Armbian_5.14_Cubietruck_Debian_jessie_4.6.2" image doesn't shut down. Neither short push of power button nor shutdown -P (issued as root) doesn't really power off the board. The red LED is lightning and the display is ON, it halts after reporting "Reached Target Shutdown". The board is OK, for a long push of PB it powers off and with a Cubieez image it shuts down well. Has anyone seen this issue? What to do with it? Thanks, T

Hi all, Today my second OPi arrived, a +2E. I already have an OPi PC which is working like a charm. So I ordered a +2E as well. I have an older monitor (Dell 2007WFP) with DVI connector and a native resolution of 1680x1050. From previous experience from the OPi PC, I know that I had to run the 'h3disp' tool to set up this resolution and to make it work via an HDMI-DVI cable. So I connected my new +2E through a normal HDMI cable to my 1080p TV, installed Armbian (Jessie desktop, with legacy kernel), updated to the latest release through 'apt-get update && apt-get dist-upgrade' and after a reboot ran 'h3disp -m 36 -d', just as I had with the OPi PC. After r…

Hello, I managed to run OPi as a media player using OpenELEC (works charmingly fast - much much better than on RasPi), bun on Armbian (legacy kernel - 3.4.113) something went not too good Firsty, I burn desktop Xenial image onto SD card, dropped into Orange, and everything worked fine besides sound via HDMI - even locally played MP3 files were stuttering, not mentioning Youtube in Chromium - CPU usage was in range of 30-40 percent. Sound in TV speakers were annoying- one second of music, long pause, repeated until I press stop button. So I gave up with Xenial, write a Jessie server image (also legacy kernel), installed XFCE with all recommende…

Hello, actually i have "Bananian" with the kernel "3.4.113-bananian", and I would like to switch to the Armbian mainline kernel! My problem / question is how does it work with the GPIO in the mainline kernel? I use these commands under the legacy kernel... (I use the modified WiringPI from LeMaker) echo "17" > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio17/direction echo "1" > /sys/class/gpio17/value But these unfortunately no longer work under the mainline kernel! I don't understand how i calculate now the right GPIO Pin. (http://linux-sunxi.org/GPIO#Accessing_the_GPIO_pins_through_sysfs_with_mainline_k…

Hi All I'm having some problem with a fresh install of version 5.30 but had the same problem with 5.27 on my Orange Pi Lite. On reboot, I can SSH into the device with no problems. but after a while connection hangs. If I wait a while after a reboot I can't SSH into the device either. I also can't ping the device after a while. Using the network manager, if I disable and then enable the wifi then everything works for a while. I have checked that the power Managment of the wifi is off. The whole time I can still browse the internet from the device with no problems. Any ideas on where to look …

Hello, I'm following my investigation to make possible an Open Hardware & Open source solution for schools (cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-37422 ) I can't use the WiFi. I didn't found information on the forum for Orange Pi PC+ on board wifi (found some but it was for USB wifi). I have downloaded Ubuntu desktop – legacy kernel on https://www.armbian.com/orange-pi-pc-plus/ and installed it on class 10 SD card with Etcher ( Armbian_5.30_Orangepipcplus_Ubuntu_xenial_default_3.4.113_desktop.img). I'm using 3A 5V power …

Hello. I am trying read to directly access GPIO PL11 (IRTX) from nano Pi DUO without success, other pins with this same code work very well. Via Userspace work well echo "363" > /sys/class/gpio/export echo "in" > /sys/class/gpio/gpio363/direction cat /sys/class/gpio/gpio363/value Then i receive 0 or 1 (This proves that hardware is ok.) My example code To compile gcc gpio_lib.c simple_gpio.c -o blink #include <stdlib.h> #include <stdio.h> #include "gpio_lib.h" int main() { sunxi_gpio_init(); //gpio_PA3 sunxi_gpio_set_cfgpin(SUNXI_GPA(4), SUNXI_GPIO_OUTPUT); sunxi_gpio_set…

Hi guys, I've been having problems on my NanoPi Duo implementing a music streaming service using Alsa PCM to output the audio. When calling snd_pcm_open with the nonblock flag set, I had snd_pcm_writei returning a broken pipe error several times per day (when continuously playing). I noticed not setting this flag and, thus, allowing snd_pcm_writei to block until there was enough room in the Alsa PCM buffer, did not show this problem. This was however unusable because the blocking behaviour slowed down the rest of the software enough to be annoying. I think I solved it now by checking with snd_pcm_avail_update if there's enough room available, …

In a brainfart i thought the rpi gpio is compatible with most arm boards. so i took one witch i had laying around and i connected the Raspberry pi DVB-T HAT module (TV uHAT). I checked if the SPI bus pins where compatible and with the help of the "Hardware_Allwinner_overlays guide" i created a overlay for the rpi-tv (used the original from the raspberry pi github). to my surprise (after some struggle) it work. // rpi-tv HAT /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&spi0>; __overlay__ { /* …

my code works just fine when executed during ssh session on NANOPI NEO CORE (booted from emmc) ! when trying to make this code run automatically on startup which is something that i have done before, unexpected delay happens after 5 seconds of continuous taking data from mic to be sent on serial port ! could not figure out what is really going on ! does it differ in terms of configuration of the nanopi when logged in through ssh !? or is there some configurations that must be handle on startup scripting !?

1.Only OpenGL ES2.1 and 1.x work: chenyifei@orangepi3:~$ glxinfo|grep OpenGL OpenGL vendor string: Panfrost OpenGL renderer string: Mali T720 (Panfrost) OpenGL version string: 2.1 Mesa 20.2.0-devel OpenGL shading language version string: 1.20 OpenGL extensions: OpenGL ES profile version string: OpenGL ES 2.0 Mesa 20.2.0-devel OpenGL ES profile shading language version string: OpenGL ES GLSL ES 1.0.16 2.glx did't work with panfrost dri: chenyifei@orangepi3:~$ cat /var/log/Xorg.0.log|grep GL [ 10447.384] (II) Initializing extension GLX [ 10447.384] (EE) AIGLX error: sun4i-drm does not export required DRI extension [ 10447.395] (II) IGLX: Load…

Hello, first post here, so sorry if did not provide enough information. I need to change spi buffer length to 8192. So far tried: 1) modprobe spidev bufsiz=8192 creating the file /etc/modprobe.d/spidev.conf and adding to it the line "options spidev bufsiz=8192" When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 2) Add to /boot/cmdline.txt: spidev.bufsiz=8192 When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 3) cd /sys/module/spidev/parameters chmod 666 bufsiz echo 65536 > bufsiz did nothing. 4) /boot/armbianEnv.txt added options spidev …

Hello, After i made the Focal update i2c is very slow and armbian-config does not start. So I made a fresh installation with Armbian Focal mainline based kernel 5.10.y But no I have the same problem. What could be the reason? Is it possible too test the i2c bus? thx greetings

System: armbian, BananaPi Pro, sd card, sata ssd, usb hdd I manually moved my existing armbian system from sd card to a sata ssd. Then I changed the rootdev in armbianEnv.txt to the ssd´s UUID. After reboot I thought everything was ok. Then after a system update I figured out that the kernel version differs from the installed kernel modules. I think the new kernel and the modules are installed in /boot at /dev/sda whereas the kernel still boots from /dev/mmcblk0p1. How can I fix this? Here some information: root@pi-nas:/mnt/boot# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda …

Hello everyone, I am using Orange Pi Zero LTS 512MB (H3 Cpu) hardware. As an image; I am using "Armbian 22.08 Jammy Kernel 5.15.y, Updated: Sep 24,202". The MAC address changes every time the Wi-Fi is turned on. I tried several different images. I tried a few simple fixes posted on the forums, but only managed to fix it for ethernet. But it was not successful for Wi-Fi. I need an image or solution that does not change the MAC address. Is there anyone who can help with this?

Hi im not Linux user not all, can someone point me how to enable SPI ? I try this: Enabling SPI Enable the hardware through config: sudo armbian-config switch on SPI in System>Hardware>SPI-spidev & save Update /etc/modules: sudo nano /etc/modules to include the following line: spi-dev Update /boot/armbianEnv.txt : sudo nano /boot/armbianEnv.txt to include the following: param_spidev_spi_bus=1 #origianl is 0 but the resonance measurement.py module expects 1 so easier to fix here param_spidev_max_freq=100000000 The commands to verify the SPI bus should return output like: $ ls …

Hi, i've a tablet that has an Allwinner A20 socs. Can i install armbian? Which are installation steps? Thank You Luigi

Hi! I have a Hackberry and i've tried to install Debian jessie for Cubieboard. First I have installed a legacy version; hackberry boot up correctly but my keyboard don't work so i have replaced script.bin and overwrited u-boot-sunxi-with-spl.bin with the latest version (http://dl.linux-sunxi.org/nightly/u-boot-sunxi/u-boot-sunxi/u-boot-sunxi-latest/) and it's work. Then i've try to use Vanilla version. As the same, hackberry boot up correctly but my keyboard don't work. I've tried to recompile boot.cmd with correct dtb but nothing changed. Then i've tried to create uImage from zImage (linked to vmlinuz-4.2.3-sunxi) and overwrite u-boot.bin with the latest (…

No sound card on 5.0 trusty vanilla, but it works on jessie. trusty: aplay -l aplay: device_list:268: no soundcards found... on jessie: aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Both are armbian 5.0 with kernel 4.4.1, on Cubieboard2 Also warning on installing cryptsetup on trusty: update-initramfs: Generating /boot/initrd.img-4.4.1-sunxi cryptsetup: WARNING: failed to detect canonical device of /dev/mmcblk0p1 cryptsetup: WARNING: could not determine root device from /etc/fstab This error doesn't appear on jessie. Also, on trusty the ha…

hi all . i try clone sd card on running orange pi (cone 32GB to 16GB). original sd is 32GB , clone sd is 16GB . 1) insert USB sd converter ( 16GB sd is in ). this is recognized as sdb because i alredy attach USB HDD. 2) i alredy install boot loader into sdb (16GB). see -> http://forum.armbian.com/index.php/topic/897-backup-restore/ so mkfs.ext4 /dev/sdb1 3)mount /dev/sdb1 /mb1 and run the next shell script ---------------------------------------- cd /mb1 df pwd cp --archive /bin /etc /home /lib /opt /root /run /sbin /srv /tmp /usr /var /selinux /boot /media ./ mkdir -p boot dev sys mnt proc 4) then halt , and repl…

Hi all, some days ago I successfully built the image mentioned above (Build environment is Ubuntu 14.04/64 bit). The only remarkable issue was the ever-repeating "firstrun" script, which was easily solved with the method mentioned here: http://forum.armbian.com/index.php/topic/1100-post-install-scripts-on-every-reboot/#entry8509 (may be ALL of the scripts should be changed this way?) But today, after checking out the actual "master", I see a lot of failed copy and sed commands until the debootstrap-ng script finally fails at Mali-libdri2. The 1st occurrence of an error was during installation of "ramlog". I've inserted a breakpoint and looked into the imag…

Hi All. First post here (and quite a newbie). I have installed Armbian on my new NanoPi Neo and followed the instructions. It is all booting OK and I now wondering how I can attach a speaker directly to the header 10 LINEOUTR LINE-OUT Right Channel Output 11 LINEOUTL LINE-OUT Left Channel Output 12 GND 0V Will this work? How can I test it as I cannot see it with ALSAMIXER. TIA.

Has anyone seen these? Awesome! Sure it's missing a few of the basic I/O ports such as monitor and KB...but with a Ubuntu headless setup...who needs keyboards/mice/monitors I have an old Raspberry Pi B [the 512mb and single core CPU) for $35 at my house running some VPN software, a TOR relay, and mumble VOIP server, this thing costs $7.99 and has a quad core! http://www.friendlyarm.com/index.php?route=product/product&product_id=132 In fact check out all their really small boards...heck the NanoPC-T3 is insane!!! Just a FYI if you haven't seen them yet

Hi, I seem to be unable to create a working image for my Orange Pi PC+ with a 4.x kernel (I want to use Docker). I had a working 4.7.3 install but a recent (this week) apt-get upgrade installed a 4.8.x kernel (and probably a u-boot) after which my Opi PC+ will not boot anymore (my home-router shows the opi for a short time but it disappears before I can do a ssh to the Opi PC+). None of the images I have or create with a 4.x kernel seem to want to work. Only the 3.4.112 images that I download will work. Since I fried my uart0 and I haven't been able to use uart1 I have not been able to debug this. So I was hoping someone has a working image with a 4.x kernel …

Hi there, I am a new user of OPi PC+, downloaded, flashed Armbian_5.20_Orangepipcplus_Debian_jessie_3.4.112_desktop.img basic setup OK, got IP, changed passwords etc, GUI starts. As I don't have USB keyboard/mouse, I've opened SSH session, then set export DISPLAY=laptop2:0 , then xterm. OK. From BT side it also looks ok: adapter blinks, I can find my BT keyboard/mouse using hcitool scan Now the problem: if I launch bluetooth-applet / bluetooth-assistant it CRASHES (assistant) at step of PAIRING device. (applet still alive). So my quiestion is, how to pair this remote device without "assistant", and make it available as "normal" keyboard/mouse? [device …