Beginners

I made a custom mini usb hub for the orange pi zero. I used the fe1.1s chip to do so. But for some reason iam getting the following error when running dmesg. And is also not recognized when running lsusb I have added both a pic of the error and a schematic of my custom pcb. ERROR 1 : https://ibb.co/HHP8DnB ERROR 2: https://ibb.co/3vHTztz Schematic: https://ibb.co/xsPv9KX Thank You for your time, hoping for a quick solution

I would like to create a LAN teaming on my Orange pi 5 plus. So combine both interfaces. The whole thing should run as load balancing so that the load is distributed evenly. How exactly do I set this up and can there be problems with something like this with Docker?

In the latest image for NanoPi M1 Plus, I enable the analog audio I/O on the card by adding overlays=analog-codec in /boot/armbianEnv.txt But the microphone on the card is disabled by default, because the ALSA control "Mic1 Playback Switch" is set to false by default on the card. Worse still, this mixer control does not appear in the alsamixer GUI, and the only way to set to true is to use the amixer command line utility, for example with: amixer cset name="Mixer Capture Switch" on on I can do this inside a first boot script, and then ALSA will persist the state between reboots. But does not seem ideal, and took me a very long time to …

Hello, I am trying to get i2c-0 working on my Armbian 20.11.3 Focal with Linux 5.9.14-sunxi64 After I run: i2cdetect -y 0 i see a plenty of dmesg errors: i2c i2c-0: mv64xxx_i2c_fsm: Ctlr Error -- state: 0x4, status: 0x0, addr: 0x77, flags: 0x0 I have enabled i2c-0 in armbian-config, tried what I could but no luck. Can anybody told me what mv64xxx_i2c_fsm: Ctlr Error means please? ls -l /sys/bus/i2c/devices -> lrwxrwxrwx 1 root root 0 Dec 22 13:05 i2c-0 -> ../../../devices/platform/soc/1c2ac00.i2c/i2c-0 The same wiring and installation (with i2c_bcm2708 and i2c_dev) works on Raspberry p…

If anyone needs to get the 3.5mm audio jack working on the N2+, here's one method. 1. Edit or create /etc/asound.conf with these lines. Copied directly from the Hard Kernel Ubuntu setup. pcm.!default{ type hw card 0 device 1 } ctl.!default{ type hw card 0 } 2. Run this script to turn on the 3.5mm audio in alsamixer. The settings are listed in the same order as in alsamixer. #!/bin/bash # 3.5MM JACK, set to max gain amixer sset 'ACODEC' '255' # 3.5MM JACK - set in/out channels (src/sink) amixer sset 'FRDDR_B SINK 1 SEL' 'OUT 2' || true amixer sset 'FRDDR_B SRC 1 EN' 'on' || true # 3.5MM JACK amixer sset 'TOACODE…

Hi all, I am using Trunk Image Hirsute(kernel 5.14) for Orange Pi Win Plus and follow below topic to compile the gstreamer: But when I am using the gst-play-1.0 --use-playbin3 --videosink="kmssink plane-properties=s,zpos=3" video.file to play the video, the whole system is hang. Then only reboot can recover the system Can you please give some suggestions? Regards, Tan

Hi Guys, My Orange Pi Zero LTS H5 had a short circuit and no longer power up. worst that it seems that i cannot find any replacement for it as market is full of H2 & H3 variants but non is H5. Perhaps its time to upgrade Armbian & Hardware by inserting the SD card in one of the below boards: - Orange Pi Zero 2 1GB RAM with Allwinner H616 - Orange Pi R1 Plus LTS 1GB RAM RK3328 -Nanopi NEO3 Mini RK3328 (though not Orange pi but seems very similar) Though i'm not sure OS would boot on different CPU / board, (i remember doing such upgrade from h3 to 5h or zero 2 to lts) I would like to avoid re-building the OS w…

On X86 and AMD64 systems they all have either the UEFI bios or the old bios. I don't know what the Raspberry Pi uses but I don't think it's UEFI. Do any of the ARM systems use UEFI? How does Armbian boot on the non-UEFI systems?

I have a project with "Orange PI PC PLUS" and a Realtek 8153B usb-ethernet adapter. My big problem is that the adapter lights do not come on, even if the rest is working. On windows systems the activity light of the adapter lights up, but in linux no (I tested on armbian 5.60 and ubuntu 18.04). I've successfully installed the linux driver from realtek's website, but the light still does not light up. Module r8152 installed and used for the device.

If you're getting poor/bad audio performance from an audio VST on the N2+, it can sometimes be the context switching between the BIG.little ARM cores. In my case, Pianoteq was giving me a lot of x-runs and wide fluctuations in performance when it switched between the 2x low-performance and 4x high-performance cores. One way to get more stable performance is to assign the application to the 4x high-performance cores like this. taskset -c 2,3,4,5 'Pianoteq 7' On the N2+ the 2x low-performance are numbered 0 and 1. The 4x high-performance cores are 2,3,4,5. 'Pianoteq 7 STAGE' is the name of the application being assigned. This is more useful …

rock@rock-3a:~$ dmesg |grep spi [ 6.279244] spi-nor spi4.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 6.279275] spi-nor: probe of spi4.0 failed with error -2 the armbianEnv is as below. verbosity=1 bootlogo=false extraargs=systemd.unified_cgroup_hierarchy=0 overlay_prefix=rk35xx fdtfile=rockchip/rk3568-rock-3a.dtb rootdev=UUID=6359cdcb-b9a7-4930-9257-30f4e34b0a4f rootfstype=ext4 overlays=spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=0 param_spidev_max_freq=40000000 Is there anyone know which version is ok for Rock 3a or rock p;i 4b?

So I was trying to compile a wifi driver for a somewhat new usb wifi device and it breaks during compilation because it expects a directory named /usr/src/<linux-headers>/arch/aarch64 but on NanoPi NEO3 the directory is named (on NanoPI R4S is the same case btw) /usr/src/<linux-headers>/arch/arm64 In order to make it work, I created a symlink under the "arch" directory called "aarch64" pointing to "arm64" and I was able to compile it. Here is what happens when I try to compile it without the symlink: pablo@callampa:~/repos/github.com/morrownr/rtl8852cu-20240510$ make clean cd phl ; rm -fr */*/*/*/*.mod.c */*/*/*/*.mod */*/*/*…

Hi All, I am trying to run Toxcore tests on OrangPi Zero inorder to run a tox client on this board. So far I tried clone git repositories of libsodium and opus. I did make and make install for both of them .I did not find any issues in installing them. I built them on OrangePi itself. I did not pass any crosscompiler prefixes to ./configure command while building them.My doubt is ,are these libraries compiled with armgcc or normal gcc ? I thougt whatever gcc is available on Orangepi is armgcc so I didnot pass any arguments to ./configure while building. make process was simple and passed without any isseus for bot libsodium and opus.But…

Out of curiosity, I installed the 'WiringOP' app so that I could view the 'gpio readall' output. Here is what happens when I do so: darren@frodo10:~$ gpio readall +-----+-----+----------+------+---+-Orange Pi+---+---+------+---------+-----+--+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.0 | ALT3 | 0 | 3 || 4 | | | 5V | | | | 11 | 9 | SCL.0 | ALT3 | 0 | 5 || 6 | | | 0v | | | | 6 | 7 …

Please forgive if this been posted before, I've done a search and found nothing. I'm running xfce desktop and as stated, window control buttons are missing from top right of windows.. I set up a temporary additional user, same on that one. Window configuration is correct.

Hello again, I was forced to reinstall OS and right now I have no sound at all. https://paste.armbian.com/omovipuyub I did try this but still no sound. cat /proc/asound/cards 0 [Codec ]: H3_Audio_Codec - H3 Audio Codec H3 Audio Codec 1 [sun9ihdmi ]: sun9i-hdmi - sun9i-hdmi sun9i-hdmi

I successfully run armbian, and I compiled Retroarch in the system, but after running it, I found that the video driver is missing. Can you help me? How should I install or compile the missing video driver

Hi, I'm having a problem with some timezones and I couldn't find anything in the web related with it. This is in a NanoiPi M1 with ARMBIAN on it. The problem is that when I run the following commands the result is not the as expected: echo "America/Indianapolis" > /etc/timezone && dpkg-reconfigure -f noninteractive tzdata and then result is: Current default time zone: 'America/Adak' Local time is now: Thu Sep 8 03:08:41 HDT 2016. Universal Time is now: Thu Sep 8 12:08:41 UTC 2016. but if I run: echo "America/Indiana/Indianapolis" > /etc/timezone && dpkg-reconfigure -f noninteractive tzdata the result is as expected: Current default…

hi everyone, I have this program that displays temperature and humidity on my orange pi, what string can I add to upload this data to the site? thanks from pyA20.gpio import gpio from pyA20.gpio import port #import RPi.GPIO as GPIO import dht11 import time import datetime # initialize GPIO #gpio.setwarnings(False) #gpio.setmode(GPIO.BCM) PIN2 = port.PA6 gpio.init() #gpio.cleanup() # read data using pin 14 instance = dht11.DHT11(pin=PIN2) while True: result = instance.read() if result.is_valid(): print("Last valid input: " + str(datetime.datetime.now()))

Hello, I am trying to make a acces point so when the orange pi has no internet i can still connect to the acces point and acces a python server that is running in a docker container on it. I managed to set-up the “hotspot” in the configuration, but once I take out the ethernet cable I cant view the site anymore from my phone that is connected to the orange pi hotspot. What can I do to make this work? https://imgur.com/a/5lecbHX

Hello, I found this Lightweight Device Mounter: https://github.com/LemonBoy/ldm I thought it was interesting enough to share it. install necessary dependencies: apt-get install libmount-dev libglib2.0-dev libudev-dev the systemd service needs ldm.conf file in /etc: nano /etc/ldm.conf with following contents: MOUNT_OWNER=usernameBASE_MOUNTPOINT=/mnt enable the service: systemctl enable ldm start the service: systemctl start ldm It should work, it does with me.

Hi I've just set up the Roseapple Pi with Armbian (legacy server Debian). As I often find (over a range of monitors) there's an overscan so bad I can't see the "login" instructions at the bottom of the screen... on all sides the text is off the edge of the screen. For the life of me I can't see WHERE to adjust the overscan - can anyone help. Pete.

Problem of top priority of Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop edition After it sticks to OrangePI PC2 Languege support. I have a favor to ask. All languages by which Languege support is besides English at present. The situation that it can't be used in the following error. org.freedesktop.PolicyKit.Error.Failed: ('system-bus-name', {'name': ':1.85'}): org.debian.apt.install-or-remove-packages In Languege support, Japanese, they seem able to establish it, when it is, the back, Mozc, install. It'll be in order to use it mostly. By this, most users. OrangePI PC2, mostly, they seem able to use…

hi I need to initialize csi camera model d-18fl271 v6 https://produto.mercadolivre.com.br/MLB-1011314593-flat-para-cmera-espia-mod-d-51fd618-v1-24-pino-_JM thank you for help

Hi all, Is there any reasonable way to login into Docker container and edit u-boot sources without running ./compile.sh script every time when container is created ? Is there any option to just create container and log into it ? I created Docker container by running command: ./compile.sh docker BOARD=bananapi BRANCH=next KERNEL_ONLY=no KERNEL_CONFIGURE=no RELEASE=stretch armbian Docker image is created. Now I want to edit some sources in u-boot directory but when I am running docker run -it armbian bash it immediately runs ./compile.sh script. I did check entrypoint definition in Dockerfile but still can't figure out how to actually …

Hi all, I had a need to install the latest version of Postgres possible across my various boards ( Nanopi4 v1 and v2 and a raspberry pi ) the only way I could find to do this, is, compile from source, I came across this howto written for the Ras Pi but it works perfectly for the other boards Here is the link https://blog.rustprooflabs.com/2019/07/postgresql-postgis-install-from-source-raspberry-pi

I have a Pinebook Pro and installed Focal xfce on its eMMC. I would like to swith to i3. So I have installed `i3`, `i3status` and `i3lock` using apt. Then I have altered the `user-session` config of lightdm from `xfce` to `i3` (actually did this at three places). With all this done, I still end up in XFCE. Hints on where to look further are welcome.

Following the Armbian Guide (Section - Fine Tuning), I was able to change the audio sink but the change is not permanent on reboot. What am I missing ? Any hints would be appreciated Thanks

Im trying to play video on CLI interface. Banana pi M1 im using.I installed VLC, MPV, mplayer but not successful. please help. my video is in pendrive.

I'm experimenting with video transcoding but am getting problems when using vdpau to decode and the hw video encoder. Using this https://github.com/stulluk/FFmpeg-Cedrus and https://github.com/uboborov/ffmpeg_h264_H3 software decode & hw encode = 15-20FPS but high CPU usage. it can do 60FPS encoding rate with 960x540 30fps h264 source dropping the compression helps a bit too (-qp 24, default is 30) hw decode & hw encode of 1080 h264 = 1FPS, using 4k h265 as the source gives 1.5 FPS ffmpeg -hwaccel vdpau -i 1080p30.mp4 -c:v cedrus264 -c:a copy -pix_fmt nv12 out.mp4 Is the video engine designed to do transcoding?

Hi, Is there anyone who know how to prepare armbian image for TBS 2910 Matrix Arm PC? HW specification you can find on tbsdtv page. - Freescale i.MX6Q, Quad Core ARM Cortex-A9 at 1.0GHz, Vivante GC2000, Quad core GPU, 2GB DDR3 Thanks for help. robert

If you have ever compiled buildroot from Amlogic, please help me. I am trying to learn develop app on amlogic based device. First I was getting compile error on 64bit Ubuntu 16.04. Something like this. Even though there was a file, 'bash' couldn't find or run. /bin/bash: /root/buildroot/x86/xxxx-gcc: No such file or directory Thinking it's something to do with 64 bit OS, I switched to 32 bit Ubuntu 16.04. However after about 2 hours I'm getting following error. /bin/bash: /root/buildroot_openlinux/output/meson8b_m201/host/usr/gcc-arm-none-eabi-6-2017-q2-update/bin/arm-none-eabi-gcc: No such file or directory /bin/bash: /root/buil…

My armbian is now very strange, I did not bind IP SSH and Pagoda Win software can login backstage, the same computer another browser login, enter the account number and password is correct, always say the account number or password error there are 5 times, cell phone connected to the same network can open Pagoda backstage login interface, enter the account number and password is correct, also prompted error. What is the problem?

Hi, I have a broken Odroid C2 from a customer. I've never used Odroid so I was wondering if I bought a Odroid C4 and insert the card will it run ok ? Don't know any info about what's in the sd card. The customer bought from a supplier he no long intends to work with ever again. Can anyone help me in any way ?

After much trial and error, I cross compiled opencv against a live armbian rootfs mounted via sshfs. I've documented the steps (including rationale and troubleshooting insights) on my blog: http://studiow.cf/blog/post/how-to-cross-compile-opencv-for-armbian-with-gtk

Hi guys, I have orange pi plus and am going to adopt camera on this board. I got GC2155 camera module from another project and it's pin compatible with Opi's Con1. Therefore I would like to use this camera module on the PIO plus. I tried to search about GC2155 from this site, but I couldn't get any information. Any guy can help about this topic?

Some people noticed that Pulseaudio mixes is showing "Built-in Audio" for all the audio devices of the SBCs. I investigated and found that the issue is related to ALSA: the devices are not really exposed by their real hardware connection (HDMI, SPDIF, ...) but just as "hw" devices. Pulseaudio is interpreting this as built-in audio because does not know anything else of the device. I'm no ALSA expert at all, copied some already existing configuration files without really understanding what I did, I found a solution. To solve the problem with SPDIF and HDMI you need to place the following two configuration files in /usr/share/alsa/card. Call the…

Hi everyone, I enabled on armbianEnv.txt overlays for uart1 uart2 and uart3 and also param_uart3_rtscts=1 param_uart2_rtscts=1 param_uart1_rtscts=1 but when I do "cat /proc/tty/driver/serial" I have: serinfo:1.0 driver revision: 0: uart:U6_16550A mmio:0x01C28000 irq:45 tx:68 rx:0 RTS|DTR 1: uart:U6_16550A mmio:0x01C28400 irq:46 tx:0 rx:0 CTS 2: uart:U6_16550A mmio:0x01C28800 irq:47 tx:0 rx:0 CTS 3: uart:U6_16550A mmio:0x01C28C00 irq:48 tx:0 rx:0 CTS I am using : ARMBIAN 5.83 stable Debian GNU/Linux 9 (stretch) 4.19.38-sunxi Can anyone help me to activate RTS on any of uarts please? Thank you

I'm trying to add a USB device using configfs to the zero but I don't want to break the pre existing serial connection on USB0 so I want to put it on USB3, the overlay has this as usbhost3 so before I spend hours designing a daughter board and trying to fix something that's never going to work the question is can I use this interface for a device.

Hello, I'm very familiar with Raspberry Pi, not so much Armbian. I have installed Armbian KDE Neon with Plasma 6 successfully and am very interested in possibilities with the Pi5.

The mailto: procedure attemps to get the default mail app from /usr/lib/x86_64-linux-gnu/xfce4/exo-1/exo-compose-mail-1 instead of /usr/lib/aarch64-linux-gnu/xfce4/exo-1/exo-compose-mail-1 Armbian Bionic desktop legacy kernel 4.4.y

Hello, Recently I installed docker on my armbian and motd got broken. Previously it was printing correctly information about traffic: RX today: 20,72 GiB But after installing docker and playing with some images motd is displaying following error: RX today: Error: Not all requested interfaces found in database or given interfaces aren't unique. The problem is that docker adds new network interfaces that are not initialized in vnstat. I've solved my issue by adding the new docker interfaces in vnstat: vnstat --add -i docker0 vnstat --add -i veth160e0f9 Perhaps /etc/update-motd.d/30-armbian-sysinfo script should somehow detect new interfac…

Hello, I'm currently working on integrating a custom-made driver into my Armbian build, but I'm facing some challenges. I've researched the process and found that it should be done through the kernel configuration. However, despite my efforts, I can't seem to find any option that allows me to add a custom driver. I've attempted placing the .ko file in a /driver folder, that I created within the source, as well as in the kernel/ folder under userpatches/, but unfortunately, it hasn't worked. I'm seeking guidance on whether it's possible to add a custom driver to an Armbian build and, if so, I'd greatly appreciate any insights or step-by-step instructi…

Hi, During the development time I keep trying and flashing the SD card all the time. Is there a way I can flash the SD card without taking out from the board with my board is connected to the computer?

Hello. I start this thread here because in not start it in 3399 forum section. I wanted preempt-rt kernel for my armbian rockpro64 so i have compiled and generated preempt-rt 4.4.167 deb kernel package. I have installed my custom kernel deb package but after reboot the system boot in old kernel not the custom kernel. How i can set the system to boot from custom installed kernel ?(4.4.167-rt176 is my custom kernel) s# ls -a /boot . boot.cmd dtb-4.4.174-rockchip64 System.map-4.4.174-rockchip64 .. boot-desktop.png Image uInitrd armbi…

Sorry if that already has been answered, couldn't find anything via search function: I have a 1920x1200 TFT attached, works well with 1080p but of course everything is a bit stretched. I tried to understand how boot.cmd/scr work, but essentially there are no entries in those files for that resolution. Search for fdt_disp_mode showed up exactly 2 hits on Google So I'm a bit lost. Is it possible at all?

I'm bringing up a custom Allwinner H3 board with Armbian. I created the required conf, u-boot and kernel patches and built the image. The SD card connector card detect pin is active high (high when card is inserted) unlike all the references available online. (Orange pis and nano pis) U-boot SPL refused to complete the boot sequence with the following error message: U-Boot SPL 2019.04-armbian (Jul 14 2019 - 17:19:54 +0000) DRAM: 512 MiB Trying to boot from MMC1: no card present spl: mmc init failed with error: -123 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Here is a snippet from the relevant part in the device…

I am trying to get the RS485 Waveshare CAN hat to communicate with the LePotato. I have Klipper and Mainsail installed which for most would be a good stopping point. I am using CANBUS on all of my printer builds and that requires a CAN hat. I am trying to get this working with this board as i can actually buy these boards. I have a few CAN hats working with Raspberry Pis so i know the original process. Does anyone have a good way to get this all working together? Even a point in the right direction would be a help. I did find a post that claimed to be able to do this but actually trying it as posted resulted with no know vendor as an error.

Hi, On my orangepi zero (256MB) running armbian image, I am observing some odd behavior that I do not fully understand. Spoiler Linux sinaspi 5.10.16-sunxi #21.02.2 SMP Sun Feb 14 21:12:17 CET 2021 armv7l GNU/Linux Distributor ID: Debian Description: Debian GNU/Linux 10 (buster) Release: 10 Codename: buster http://ix.io/3mQX In an effort to 'harden' the orangepi zero configuration (by making the user experience annoying), I have shortened the sudo password prompt timeout. On the orangepi zero board, the following setting results in a timeout of only 2 seconds, instead of 15 seconds: #[B…

$ cvt 3840 2160 # 3840x2160 59.98 Hz (CVT 8.29M9) hsync: 134.18 kHz; pclk: 712.75 MHz Modeline "3840x2160_60.00" 712.75 3840 4160 4576 5312 2160 2163 2168 2237 -hsync +vsync $ xrandr --output HDMI-1 --mode 3840x2160_60.00 xrandr: Configure crtc 0 failed $ xrandr --verbose Screen 0: minimum 320 x 200, current 3840 x 2160, maximum 7680 x 7680 HDMI-1 connected primary 3840x2160+0+0 (0x41) normal (normal left inverted right x axis y axis) 708mm x 399mm ... CRTC: 0 CRTCs: 0 I would like to setup 4k with a PI400. I found https://docs.armbian.com/User-Guide_Fine-Tuning/ and followed the instructions Did I something wrong, or is this simply…

Time_2018/02/26 OrangePI PC2 Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop s problem OrangePI PC2 Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop was downloaded yesterday. It was started and seen once again. Fortunately, language support, they seem to move, it was. 1. fumio@orangepipc2: ~/Desktop$ df -h filesystem size user Avail Use% Mounted on ............... tempfs-root 498M 498M 0 100% /media/root-ro overlayroot 498M 498M 0 100% / ...... ..... tempfs-roo and overlayroot…

Hi to all, My box was running in the same issue. So have I've had a look into the logs. In my case it was the knowing Bug https://bugs.launchpad.net/ubuntu/+source/lirc/+bug/1768291 > lirc is flooding the syslog with two lines each second [date&time] flupp lircd[1323]: lircd-0.10.0[1323]: Error: Cannot glob /sys/class/rc/rc0/input[0-9]*/event[0-9]* My solution was to uninstall lirc. Have nice day deBugger @moderator the thread https://forum.armbian.com/topic/6229-ramlog-full-no-space-left-on-device/ was closed feel free to join.

Hello, I tried to use the power button on my Rock 4 C+ running Armbian 23.02.2 Bullseye with Linux 5.15.93-rockchip64. It is able to power off. But I can't boot up the controller. When I use the debian based radxa image the button works like expected. I found this at the rk3399-rock-4c-plus.dts of the radxa kernel. &rockchip_suspend { status = "okay"; rockchip,sleep-debug-en = <1>; rockchip,sleep-mode-config = < (0 | RKPM_SLP_ARMPD | RKPM_SLP_PERILPPD | RKPM_SLP_DDR_RET | RKPM_SLP_PLLPD | RKPM_SLP_CENTER_PD ) >; rockchip,wakeup-config = < (0 | RKPM_GPIO_WKUP_EN | RKPM_PWM_WKUP_EN | RKPM_U…

Since u-boot can deal with the original initrd.img, do we still need to convert it into uImage?

Hi all! I try to run ./demo file, that must make diode blinks on 4 pin. But nothing happens... It finds correct board name (Running on a Orange Pi One), but blinking doesn't works. I also try simple c++ program: Spoiler #include <stdio.h> #include <stdlib.h> #include <stdint.h> #include <string.h> #include <unistd.h> #include <time.h> extern "C" { #include <armbianio.h> } int main(int argc, char **argv) { int i, rc; const char *szBoardName; // Initialize the library rc = AIOInit(); if (rc == 0) { printf("Problem initializing ArmbianIO library\n"); return 0; } szBoardName = AIOG…

Hi, installing a WiFi Hotspot eliminates the wlan0 from the network manager. Files like hostapd, dnsmasq must be edited manually. I have 2 files for hostapd: ll /etc/network/interfaces.d total 8 -rw-r--r-- 1 root root 163 Mar 25 18:55 armbian.ap.nat -rw-r--r-- 1 root root 154 Jan 20 12:16 orig_armbian.ap.nat hk@orangepizeroplus:/etc/dnsmasq.d$ cat /etc/network/interfaces.d/* # armbian NAT hostapd allow-hotplug wlan0 iface wlan0 inet static address 192.168.100.1 netmask 255.255.255.0 network 192.168.100.0 broadcast 192.168.100.255 # armbian NAT hostapd allow-hotplug wlan0 iface wlan0 inet static address 172.24.1.1 ne…

armbian-config has significantly changed in Bookworm/Kernel 6.6. It looks to me that its not reflecting the actual device settings. Please refer to the attached screenshot from /boot/armbianEnv.txt. Compared to Bullseye/Kernel 6.1.92 I see an additional line "fdt_overlays, where all the dtb settings from the new armbian-config appear, fdt_overlays=sun50i-h5-analog-codec sun50i-h5-i2c1 sun50i-h5-tve sun50i-h5-uart2 sun50i-h5-usbhost0 sun50i-h5-usbhost1 sun50i-h5-usbhost2 sun50i-h5-usbhost3 but they seem to not having any effect. In 6.1.92 this line does not exist. The real dtb settings are still in the line above overlay_prefix=sun50i-h5 overlays=i2c1 uart1 usbho…

Posting this because I want to share the solution. Got this error when trying to cmake OpenCV : -- Found PNG: /usr/lib/arm-linux-gnueabihf/libpng.so (found version "1.2.50") -- Looking for /usr/include/libpng/png.h -- Looking for /usr/include/libpng/png.h - found -- Found OpenEXR: /usr/lib/arm-linux-gnueabihf/libIlmImf.so CMake Error at /usr/lib/arm-linux-gnueabihf/cmake/Qt5OpenGL/Qt5OpenGLConfig.cmake:27 (message): The imported target "Qt5::OpenGL" references the file "/usr/lib/arm-linux-gnueabihf/libQt5OpenGL.so.5.3.2" but this file does not exist. Possible reasons include: * The file was deleted, renamed, or moved to another locat…

This is a quick notes Guide for the Installation of THINGER.IO MAKER SERVER & MongoDB on ARMbian My Device : Cubietruck OS Installed : Armbian Bionic mainline kernel 4.14.y or 4.17.y ************************************************************************************************************************************************************************ sudo apt update sudo apt upgrade sudo apt install git apt-get install snap apt install snapd snap install hello-world sudo snap install thinger-maker-server *******************************************************…

Hello to everyone! I'm trying to solve the issue which is currently being discussed here and I've been forced to revert back to the ancient version in the title. The problem is that along with my OPi PC I use a cheap wireless adapter based on the MT7601. Here, I've found out that the support for these cards had been merged to upstream since 4.2 kernel versions indeed with Armbian Focal 5.10.4-sunxi it worked out of the box like a charm. Unfortunately, it isn't the case with the version I'm currently on, this adding another massive headache! I've found this really interesting thread where it is discussed how to add support for the MT7601. Everything went fine apart …

Thanks to all the good contribution. I was able to follow the instructions by @janng0 and @xeniter and got the fuses burned. I was able to write TOC0 to SPL with the jemk script and put the SPL to my SD card and it is booting! But... The Bootprocess hangs after "Found device /dev/ttyS0" (i am using a dietpi image). I was using sunxi-spl.bin from git://git.denx.de/u-boot.git after checking out the same version of u-boot as in my dietpi image (2020.10) and compiling it leaving default configs in menuconfig. do I need to enable more features during u-boot compilation? Where did you get your sunxi-spl.bin get from?

Hello, I've installed armbian s912 stretch debian desktop 5.75 on my video game console board, Pandora's box X 3d or 7, they're the same. That's run perfectly but i have just one usb port functional and I want tu use an usb hub(4ports) for adding and use my mouse and a Wi-Fi adapter but it doesn't work because only one device work, if I plug 2 devices, that doesn't work much. and lsusb command doesn't show the 4 hub's ports. Thank you.

Dear all, My Orange Pi plus 2E was working fine before. I was able to install both the desktop / server version to the eMMC. However, one day I try to run a benchmarch & speedtest script from tocdo.net, the Pi freeze and unable to boot from eMMC ever since. I've tried to boot the Pi with an SD, it's working fine. I tried to format the eMMC - no problem at all, but when I tried to install the OS to the eMMC, it's always stuck at around 55% (for the server version) and 10% (for the desktop version). I try to run the command from URAT, SSH and the local PC itself but not working. Can you advise on this case? Below is the log from URAT: …

I'd appreciate some advice for using an Orange Pi running usbip as a host to extend a UPS's USB connection to a Windows desktop client on the same subnet. I've done a little research and from what I'm reading this should work but I'd like to hear which Orange Pi, arm OS and usbip version you recommend. Thanks!

Hi all, I use orange pi one + armbian + wavesahe 7 inch display. I got a problem with Touchscreen does not work. I look Waveshare used goodix gt811 touch controller, so when i check on the kernel /lib/module the driver not exist, only gt9x and gt82x. And then i check release log linux kernel, goodix gt811 just present start from kernel 3.5 while armbian is 3.4.x. So, how to make the Touchscreen to work? Thanks.

I have a Odroid XU4 board that I am trying to build an image for and it will not boot from any images I have built from the compile.sh pulled from github. The board u-boot led doesn't turn on (solid blue) and nothing is displayed from the hdmi port. I select SD card image and have tried writing it with Win32 imager, Etcher, and the dd command. I did get an Ubuntu image downloaded from Odroid to work so the board is not faulty. Nothing has worked and I'm at a loss as to why when I personally compile an image it does not work. Thanks for the help

I'm using an Orange Pi Zero Plus 2 trying to setup double spi. By configuring my boot armbianEnv.txt I am able to see two spi devices. verbosity=7 logo=disabled console=both overlay_prefix=sun50i-h5 overlays=analog-codec spi-add-cs1 spi-spidev uart1 uart2 usbhost2 usbhost3 param_spidev_max_freq=12000000 param_spidev_spi_bus=1 param_spidev_spi_cs=1 user_overlays=spi-double-spidev-cs sun50i-h5-spi-cs usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u However I only see one chip select working on the physical board. Is there something I need to do to assign with gpio the second chip select will be on? Thanks, Dan

About 6 months ago I started a music project with the Raspberry PI Zero 2W. The project is a module to generate weird and wonderful drone music/sounds (example here) Because of the fact that it's nearly impossible to got hold of the Raspberry PI Zero 2W, I want to "port" the project to an alternative and available board with the same footprint and pinout; the BPI M2 Zero would be perfect. I have quite a challenge though; See image: The exact setup below with an Raspberry PI Zero 2W (O/S: Bullseye 11) and the install procedure described here, runs absolutely fine --- but now I want this setup to run on the BPI M2 Zero (O/S: "Armbian_20.05.1_Ba…

Hi there. Any one have Schematic of LeMaker Guitar CPU Module? I found on a YouTube Video it was available before on official site download section but not available now. Only the Guitar Base Board Schematic now available. It will be very helpful if anyone can share. Thanks in advance. Regards.

Hi, I downloaded Armbian Bionic for OrangePi Lite from: https://www.armbian.com/orange-pi-lite/ and everything works fine, except audio recording from microphone. Error: root@orangepiserver:~# arecord test.wav ALSA lib confmisc.c:767:(parse_card) cannot find card '0' ALSA lib conf.c:4528:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory ALSA lib confmisc.c:392:(snd_func_concat) error evaluating strings ALSA lib conf.c:4528:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory ALSA lib confmisc.c:1246:(snd_func_refer) error evaluating name ALSA lib conf.c:4528:(…

How is i2c1 and i2c2 mapped on Nanopi Duo? I can configure in armbian-config, but all the Duo pin diagrams only show i2c0.

hi i used to compile a kernel for raspberry pi 3 and i forget to compile with debug info ..the kernel work correctly but when i recompiled it ihe z image not work and my raspberryy pi 3 can t boot..

I'm looking for the ability to extract coarse motion estimation from the h.264 encoder. These vectors are calculated as part of the compression algorthm and should be done on the hardware in real time - just a matter of extracting them. This extraction is done on the Raspberry Pi with "raspivid -x output". It is also exposed in picamera. Does anyone know if there is a similar capability to extract the motion vectors? If not, how one might go about doing this in python/c++? thanks, philip

I just had an OrangePi of mine at a customer site, die on me. It just stopped responding to ping, so I made them a new MicroSD card and mailed it out. Now I think the Pi hates the Stretch release or something and fries SD cards? Check this out: https://pastebin.com/KaMk70vS Literally first login! only been up 15 minutes

it says connected to local host but it wont connect to my printer it keeps saying cups error please help

Are there any commands to show information that could tell me about the level of power consumption ? E.g.: energy saving state of CPU or the like ? On the SBC i am using, i think the power consumption is lower when running the same setup with kernel 5.4, and higher with legacy kernel 4.4. Alas, 5.4 has other problems, so i want to try to figure out what settings/features reduce power consumption in 5.4 and maybe i can then configure them equally in 4.4. This is rockpi4a rockchip3399. If there is nothing generic enough about the topic, i can ask on the forum for that chip.

good morning . can you explain something? . is it possible to use voice control to transmit audio wirelessly to the speakers with nanopi + NanoHat PCM5102A as happens with google assistant + chromecast audio?

Hello, I'm trying to connect hw125 to orange pi r1, but nothing happens. I searched both on the internet and through gpt. The kernel is the latest, I compiled it myself.

There are already several boards with the small SPI flash installed. This is perfect for the u-boot storage. Than the board starts from this SPI flash and looks for the /boot folder on SD card and USB storage. I've moved the system from the SD to USB HDD included the /boot folder and removed the SD card. When I power-on the board, the HDD starts and everything works fine. But when rebooted, the HDD is suspended at the shutdown end and the u-boot doesn't wait until it starts again and the booting fails as "No USB storage found". Is there any way how to disable the HDD suspend in the system? I was looking around how to disable this function somehow in the HDD itself ( Maxto…

Hello, Trying use SNAPD on Rock64 board (4G RAM). After install SNAPD and LXD (or other SNAP app) everything works. But once I reboot board - it won't start and I see Kernel Panic on screen. Any ideas why and how I can try to fix it? Thanks.

How to change font / view size in qbitorrent. The menu items are very small. In the settings under Appearance no effect on the font size in qbittorrent. $ hostnamectl Static hostname: Icon name: computer Machine ID: 4147 Boot ID: 129d Operating System: Debian GNU/Linux 10 (buster) Kernel: Linux 5.4.20-rockchip64 Architecture: arm64 $ uname -a Linux RockHomeServer 5.4.20-rockchip64 #20.02.1 SMP PREEMPT Mon Feb 17 04:45:00 CET 2020 aarch64 GNU/Linux Thank you very much!

Hello, I want to connect my orange pi PC+ on my cathode ray television over the jack video output. All topic I found regarding that are based on very old armbian version what is the way to get this working thank you for your help in advance regards Guillaume

Hi Armbian Community, I Am Really New To This Forum, So Forgive Any Mistakes.... SO, I Have A X96 (Not Max Or Mini Just X96 Normal).Used It More Than 3 Years As A TV Box. But The System Can Do More Than Just A Android TV. So I Have Flashed "Armbian_20.07_Rk3328-tv_bullseye_current_5.7.8_desktop" To My X96 It Works Fine But I Need The Wi-Fi Chipset To Work. I Have A Home Router With Just 1 LAN Port. Which Is Currently Connected To My PC. What Can I Do Now?? Any Solutions?....

Hi Folks! Thanks for the great software. Install went very smoothly and my board is stable. Last step is to enable my DAC card. I know that it is used in the Volumio image for this board ... so I assume (!) that support is in Kernel already. Any hints on how to get it working? I was digging around for a dtoverlay to enable ... but no luck so far. thanks!

[ 11.799225] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, de v addr: 0x48) [ 11.804169] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, de v addr: 0x48) when using i2c-bus,there is too much log in the dmesg, how can i disable this kind of log ?

I’d like the red led to indicate wifi activity. The led triggers phy0rx and phy0tz are missing on OPiZ+ (H5) however. On OPiZ (H2) this worked fine – any ideas? Hammy

I have a carrier board from codico: https://www.codico.com/en/carrier-board-h-home-control-evb-for-red-yellow-beet-modul I've followed the pdf file from the above link to set up a Rasperry Pi and it all works fine. However, when swapping for my NanoPi Neo Core, even though the drivers load correctly, and I see SPI comms going back and forth on the oscilloscope, I am not connected to the internet. This is what ifconfig returns: What could be the difference between rpi and this board that this happens? Any guidance on how to resolve it would be deeply appreciated!

Hi: I recently installed Buster xfce desktop on Cubox i4pro. Everything works great, except I can not power off cubox. I tried various commands, shutdown -h now; systemctl poweroff; and hatl; but the system first appears to halt, where I can not ping the ip addrss of cubox, but then it reboots. Is there some way to powerfoff cubox? My current system is nightly, but I also tried stable with latest kernel. $ uname -r 5.10.21-imx6 $ cat /etc/os-release PRETTY_NAME="Armbian 21.08.0-trunk.26 Buster"

Has anyone managed to get armbian running on the Allwinner T113-s3? I've been looking into getting it running and there's really no alternatives to Tina linux that I can find. Looks like it works with AWBoot and XBoot as a bootloader so it shouldn't be impossible. I'm completely new to this so if anyone knows anything it would be greatly appreciated. 😄

Hey Igor, I noticed on another thread that you're running the ClearFog Pro on a 4.12 kernel; What did you do to get the mv88e6xxx working? Every build against mainline I do for either 4.4.96 or 4.13.11 ends up with a port that doesn't properly detect link status (up or down) and doesn't receive any traffic.

Hey there, has someone got bluetooth working on his Banana Pi M2 Berry? I looked up that the bluetooth chip (ap6212) is connected via UART3, so I changed the "ttyS1" to "ttyS3" in /etc/default/ap6212, but the service 'ap6212' crashes with several input/output errors. While reading about similar problems with different boards I discovered that the ttyS3 / UART3 is not enabled on my device, at least "dmesg | grep ttyS3" does not find anything, while "dmesg | grep ttyS0" and "dmesg | grep ttyS1" does show that these devices are enabled. There adding the lines "overlays=uart3" / "param_uart3_rtscts=1" helped them, but these lin…

Hi to all: I run a odroid N2: / _ \ __| |_ __ ___ (_) __| | | \ | |___ \ | | | |/ _` | '__/ _ \| |/ _` | | \| | __) | | |_| | (_| | | | (_) | | (_| | | |\ |/ __/ \___/ \__,_|_| \___/|_|\__,_| |_| \_|_____| Welcome to Armbian 20.11.6 Focal with Linux 5.9.14-meson64 System load: 18% Up time: 20 min Local users: 3 Memory usage: 20% of 3.55G IP: 192.168.5.70 CPU temp: 43°C Usage of /: 11% of 57G Try to install a sonso api on my system. After a reboot i get a strange error with python . …

can someone tell me which board hardware supports video decoding with armbian? preferably with (C)VLC? Thanks a lot for your help!

I have an orange pi lite, I want to use the lcd ili9341 TFT 320X240 2.8 Inch touch screen, and by header 34 pin and how the installation connections I don't know I need your help. I be very grateful. The OS is "Armbian_22.08.2_Orangepilite_jammy_current_5.15.69_xfce_desktop" And I'm looking for 2.8 inch LCD setup codes on Armbian for Orange Pi Lite!

Ramlog.service postrotate will execute a cat from /var/log.hdd directory to /var/log directory while rsyslog.service is always outputting stuffs in the background to /var/log directory. This in general has no problem except for some files which are mostly preoccupied with output from rsyslog during logrotate activation, namely syslog and a varieties of journals entries. I have found some of these postrotate failures with cryptic messages as write errors from cat and corresponding rsyslogd omfile module stating lost messages. I suspect two independent processes competing to send output to same files hence causing these errors. I don't know enough of detail but I think ther…

The current kernel version of the board is 4.9.7, and I am trying to update it to 5.9 with the Real Time Kernel patch. For compilation I first got the default sunxi config as follows: make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- sunxi_defconfig After that I enabled Expert Mode to be able to select the Preempt RT option in General Options of the make menuconfig. After that I started compiling, and after a while I got the following error: DTC arch/arm/boot/dts/sun4i-a10-a1000.dtb In file included from arch/arm/boot/dts/sun4i-a10-a1000.dts:46:0: arch/arm/boot/dts/sun4i-a10.dtsi:44:41: fatal error: dt-bindings/thermal/thermal.h: No suc…

I try to boot Armbian build for Rock Pi Model B but the screen stays black. The Armbian Download Page says for Model SE use Model B builds. Is there a configuration that i can change to make it work. I hope somebody can help me.

Hi I am referencing below from this closed thread: So currently I set up wifi through an initial ethernet connection, but the issue is when the wifi connection is successfully setup, that connection does not become active until ethernet is unplugged and board rebooted. Wifi is setup through nmcli...is there an option we are missing that is preventing both network interfaces from working simultaneously? currently just using "sudo nmcli dev wifi connect ssid password password"

Sorry but i can't change display resolution with armbian 5.75 in one orange pi pc plus: ARMBIAN 5.73 stable Ubuntu 18.04.2 LTS 4.19.20-sunxi -h3disp not found -armbianEnv.txt not working -Documentation not easy and don't work Thanks a lot.

Last time I tried to update to Buster I noticed OpenMediaVault had issues (due to missing repos I think). But now that OMV 5 has been (apparently) released it should be a non issue upgrading to Buster. Has anyone had isssues upgrading to Buster with OpenMediaVault installed as of recently? Thanks in advance.