Allwinner sunxi

Hi, I have some armbian 5.38 (kernel 4.11.5) installations and recently updated them. With this update I got kernel 4.14.18. When I executed command "armbianmonitor -m" I used to get something like this: :~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC 10:52:13: 528MHz 0.35 21% 2% 18% 0% 0% 0% 40.8°C 41.0°C 10:52:18: 528MHz 0.52 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C 10:52:24: 528MHz 0.47 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C Now after update, and kernel 4.14.18 among other new packets, I got this: …

I have a board of Orange Pi One Plus with installed pihole (https://pi-hole.net/). Armbian image is Armbian Buster with latest updates. PRETTY_NAME="Debian GNU/Linux 10 (buster)" Each 2-4 hours the device hangs and not able to respond to any command until I reboot it. The max uptime that I was able to gain was ~25 hours. I've changed power adapters, powered it via microUSB - same result. Looking at the logs I really have no clue why it stucks. Attaching debug, kern and syslog. Probably someone may pinpoint what's going on. P.S. Previous OPi One (not Plus) worked for that purpose like a charm. Didn't know that bying Opi One+ for upgrade will buy me loos…

Hi, guys. I'm using the last Armbian Cubieboard image (Armbian_23.11.1_Cubieboard_bookworm_current_6.1.63.img.xz) on my "Gemei G9" Allwinner A10 tablet. But via serial/UART the boot process stuck forever in "Starting kernel ...". Any tips on how to get the kernel to start? Thanks in advance Here is my boot log: U-Boot SPL 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) DRAM: 1024 MiB CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 ns16550_serial serial@1c28000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 U-Boot 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech…

Hello again, since I use the NAND-Flash to boot and I want to use the new kernel, which doesnt support NAND yet, I'm curious if its possible to use both: 1. Can I boot the new kernel from NAND? Since the new kernel is started after uboot, it should be possible? 2. Afterwards I have no possibility to update the kernel again. Or do I have? (Without SD-Card) a.) the nand-tools requires the nand-driver??? Or is there a possibility to writea prebuild image to nand without kernel-nand-support? b.) is it possible to start an old kernel from the new for upgrading? Tried "kexec uImage", but it doesnt work. Maybe I need the zImage instead of uImage? best regards

After i've upgraded to 5.00, and upgraded the legacy kernel to vanilla (mostly for hardware crypto), i've noticed strange errors: blocky video play from dlna, and from samba too. So i did some test, copied few files on my cubieboard2, and compared the sha hashes of both version, and sometimes the cb2 version is changed, sometimes not. Also i see that a lot of synced files became different on cb2. Is there a way to do some in memory tests to verify how the hw crpyto works? For example random numbers -> hw encrypt -> decrypt -> check if still the same. These test i've made: -as i'm using the encrypted HDD as a backup storage too, i've compared the sour…

Hi, First, i'am french, excuse my bad english... I have a problem with my orangepi zero using a bme280 weather sensor with i2c. (I have 2 sensors) After long search and try, i've found the way to make this sensor working with the orange pi zero, by reading the datasheet where it's indicated that you must put CSB to Vdd to select i2c interface. !!! - I never wired this pin to my rapsberry pi and it always work , never see in any tuto too!!! Th problem is that I don't read good values, it seem that the values are always the same, based on calibration . I try to figure out what happen but i'm not so friendly with i2c pro…

Hi! I've coded a script that allows me to create a bootable disk of my favorite systems for different boards. it does a dd of the mbr (446 kb), then with fdisk and mkfs create the partitions, and at the end copy all the data for the root partition and others. This works for raspberry pi2 pi3, but for the orange pi it works only if the sd card is the same of the one used to backup the system, so i've investigated if the fstab or boot.cmd has some uuid of the disk but everywhere i found the device name instead of the uuid identifier. I don't understand why the orange pi lite don't boot with a different sd card if it have the same mbr and the same partitions. app…

Good afternoon. The problem is indicated in the title. The computer is connected to my monitor via HDMI and the screen resolution is only 1024x768. Which is inconvenient to use. I saw a similar topic raised on the official forum of a single-payer in 2019, but no one answered there. Is this a problem of the computer itself or the Linux kernel or drivers?

Hi. Recently i upgraded to Armbian_5.65_Orangepilite_Debian_stretch_next_4.14.78 and i have two problems. I can not read the thermal zones properly with neither of those: cat /sys/class/thermal/thermal_zone0/temp cat /sys/devices/virtual/thermal/thermal_zone0/temp cat /etc/armbianmonitor/datasources/soctemp because i have results like "30371". But when the system starts the correct temperature is displayed: Welcome to ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.19.20-sunxi System load: 0.07 0.15 0.10 Up time: 10 min Memory usage: 29 % of 493MB IP: 192.168.1.46 CPU temp: 33°C Usage of /: 10% of 15G and with armbianmonit…

Did someone try to compile latest mysql 5.7 on cubietruck? I've got this error: In file included from /mnt/data/tmp/mysql-5.7.10/include/lf.h:20:0, from /mnt/data/tmp/mysql-5.7.10/mysys/lf_alloc-pin.c:98: /mnt/data/tmp/mysql-5.7.10/include/my_atomic.h:62:4: error: #error Native atomics support not found! # error Native atomics support not found! ^ In file included from /mnt/data/tmp/mysql-5.7.10/mysys/lf_alloc-pin.c:98:0: /mnt/data/tmp/mysql-5.7.10/include/lf.h: In function ‘lf_pin’: /mnt/data/tmp/mysql-5.7.10/include/lf.h:97:3: warning: implicit declaration of function ‘my_atomic_storeptr’ [-Wimplicit-function-declaration] my_atomic_s…

Hi, Creating a build for OPiPCPlus, mainline/dev/4.11, xenial,desktop. Need to enable the UDA1380 device in my local kernel build, yet I see some ..obstacles.. Tried initially to do a KERNEL_CONFIGURE="yes" in compile.sh but after started the compile and reached the point of menuconfig the UDA1380 option did not got presented (might be because there is no tristate string in mainline sound/soc/codecs/Kconfig..) so I reverted it back to normal. After the first attempt, I tried by modifying the lib/config/kernel/linux-sun8i-dev.config and added "CONFIG_SND_SOC_UDA1380=m", tried the compile again and waited to finish, yet at the end, although the ot…

I am try to activate the audio for cubieboard 2 with the OS armbian with the kernel 4.1.4 and I do not get it by the output jack. Before I install this distribution, I had a cubieez and this OS worked the audio with alsa. Is impossible have audio with this kernel? Thanks in advance!

Hello I am using Orange Pi Zero 3 and I installed the latest armbian version on it I have the picture through HDMI, but there is no sound!!! Isn't one of the main uses of these boards multimedia?! Why shouldn't this board have sound?!!! I have checked all the settings. Thank you. If there is a way, please help me My armbian version: Armbian_community_24.5.0-trunk.667_Orangepizero3_jammy_current_6.6.31_gnome_desktop

Hi, I'm still experimenting with different "Linuxes" on that boards.. to get an LCD Display (LVDS) and the Ethernet part working. It cost me days to figure out that there seems to be an ugly glitch. with the stone age "cb2-dvk-sdcard-lubuntu-lcd v1.0.img" I get an working X11 Desktop with 800x480 ..but Ethernet doesn't work. I've checked those fex files (script.bin, script.fex) but couldn't figure out what's going on. I think that doesn't interest someone besides me, ok., got that. Now I've tried the actual "Armbian_community 24.5.0-trunk.667 Jammy with Linux 6.6.31-current-sunxi" that I've downloaded from somewhere here (…

On my new orange pi zero I hooked a pl2303 usb converter to the three serial pins and use "screen /dev/ttyUSB4 115200" to connect. This gives garbage on boot, with occasional strings of meaningful info like "Orange Pi" or "Debian". Same converter worked fine on my Raspberry Pi Zero. I'm suspecting the Orange Pi is just too fast and either the pl2303 or my Debian system can't keep up. Does anyone have the serial console working? Should I try a cp2102 instead, or maybe reconfigure to a slower speed? When I configured a DHCP server and hooked it up via ethernet, I can get in fine. Armbian 5.25 jessie, 3.4.113 kernel. 64GB sandisk Ultra plus uSD card, power from…

Hi, I have an Orange PI Lite on to which I'd like to install the latest Armbian release. I had Armbian Xenial installed on the Pi Lite quite some time ago for test purposes and put it to one side while I got hardware for my Pi Lite set up for its intended use. I wiped the SD card and I was ready to download, install and set up the latest Armbian Xenial on my Orange Pi Lite when I notice the sub-heading "desktop legacy kernel 3.4.y". I'm not sure if this description appeared previously but my question is does this mean that this version, i.e. "Armbian Xenial desktop legacy kernel 3.4.y", although currently supported is no longer being updated and will theref…

Hi folks, I'm trying to figure out what the current status of USB OTG support is, as applies to the Orange Pi Zero. I'm trying to use the HID gadget features, but I'm triggering a segfault and stack dump when I try to set it up. I'm using the hidonly.sh script found here (https://github.com/crmulliner/hidemulation), with a tiny modification to make it more generic: - echo ci_hdrc.0 > UDC + ls /sys/class/udc > UDC On running the script, I get the following (using the serial console): I found this report, which appears to be identical, but I'm not sure what it means, or what I should do to get working OTG support on the OPi Zero. Is the…

Ethernet was working fine for me, up until I rebooted the board. The LEDs on the ethernet port blink briefly during boot, but once booted they are off, and the board does not have an IP address. Via serial console I undid the change I made prior to the fateful reboot (adding 'overlays=uart1' to '/boot/armbianEnv.txt') and rebooted again, but to no avail. Having searched for the issue, I also confirmed that my power supply is sufficient; running 'stress -c 2 -m 2', and measuring across pins 2 (5V) and 6 (GND) of the 40-pin header, I get 5.05V. As I don't have a network connection, I did not run 'sudo armbianmonitor -u', but I gathered the following …

I created a Jessie image for BananaPi with the latest / next kernel, and when booting the image, it get's stuck on "A start job is running for LSB: Raise network interfaces". It never seems to complete raising the interface, and since there is no time limit, this goes on forever. Creating a Wheezy image seems to work fine (also using latest / next kernel). Any suggestions on how I can get the Jessie image up and running? Thanks.

Hello, I have a fully working customized Armbian on OrangePi PC Plus. There are two partitions, one for the rootfs, second mounted as /home I want to convert the root partition to squashfs, and use the squashfs file to boot from. I already converted the root partition to squashfs file, I can mount squashfs file, and the contents are correct. I even tried to mount it via fstab and it works. I searched everywhere, obviosly not enough, but I cannot find a way to boot directly from the squashfs file. The idea is to have only squashfs file and rw partition for /home Please, can somebody help me, or point me to the right instructions ?

Hello I've just started struggling with Lamobo-R1 SATA problems and I'm facing the well-known bad customer service from SinoVoip. With the help of this forum I got finally the HD spinning but I've not seen anything yet related to hd-idle package. I'd like to know if anybody uses it and if the instructions on http://hd-idle.sourceforge.net/ are correct to recompile for the BPI-R1 board. As a matter of fact I'm stuck at the line saying "Run "dpkg...." Thanks! V.

I compared two boards （opi zero h3 and opi zero plus h5) and found that cpu pins for 26 gpio are the same . so I modify the code in wiringPi about cpu detection to force return true value . and it works. the step: 1. git clone https://github.com/xpertsavenue/WiringOP-Zero 2. modify the code in WiringOP-Zero/wiringPi/wiringPi.c (or using the attached file to replace）。 3. make && make install 4. run "gpio readall " to test 5. run "gpio write 30 1" (the red-led on, wiringpi pin 30 control red-led status). wiringPi.c

Hi. I want to install RTL8188fu on this orange pi pc but I have no luck. Bus 003 Device 005: ID 0bda:f179 Realtek Semiconductor Corp. RTL8188FTV 802.11b/g/n 1T1R 2.4G WLAN Adapter I'm using this repository https://github.com/kelebek333/rtl8188fu , but....: orangepipc:~:# sudo dkms install ./rtl8188fu Creating symlink /var/lib/dkms/rtl8188fu/1.0/source -> /usr/src/rtl8188fu-1.0 Error! Your kernel headers for kernel 5.15.93-sunxi cannot be found. Please install the linux-headers-5.15.93-sunxi package or use the --kernelsourcedir option to tell DKMS where it's located. sudo apt install linux-headers-$(uname -r) Reading package lists…

Hello, with 3.4. kernel I could use my csi-cam on my R1: #5.0 Mega Pixel Banana PI Camera Module for Android #and Linux. OV5640 chipset, CSI connector #Price: US $24.00 / piece from aliexpress sudo modprobe ov5640 sudo modprobe sun4i_csi0 #video stream #mplayer tv:// #snapshot mplayer tv:// -vo png -frames 1 Now I switched to armbian 4.7 with 4.2.6 to use new wifi-usb-drivers but I saw that those modules are not supported in the new kernel. :-( Source of drivers: https://github.com/LeMaker/linux-sunxi/tree/lemaker-3.4/drivers/media/video/sun4i_csi https://github.com/LeMaker/linux-sunxi/blob/lemaker-3.4/drivers/media/video/sun4i_csi/device/ov5640.c Did a…

Hello to all! I have banana pi m2+ with Allwinner H3. OS: ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i I program linux kernel driver. And I am can't run R_UART. I write to register any value, and read value alway zero. It seems that APB0 bus is not cloked. Or device R_UART reset asserted. What I do wrong? Sincerely, Dmitriy.

Hello, I have a Cubieboard2 and armbian in a vanilla kernel with jessie flavor. This board has a 2 cores processor. When I am logging in, load average is shown and becomes red when it is greater than 1.0. Since, there are 2 cores, it should be colorized only when it reaches 2.0. Is it possible to have this feature (taking care of each board's number of cores) ? Thank you

Hello, a few months ago I wrote a tutorial to enable the 7" touch display for Banan Pi and Banana Pi Pro. Unfortunately the files (*.dts e.g. sun7i-a20-bananapro.dts) have changed and I don't know how to integrate the patches in the current armbian version. Does anybody know how to do it? Is there already a overlay to enable it? Thanks. Steffen

Hello, Upgrading uboot 5.25 to 5.35 on Armbian_5.25_Lime2_Ubuntu_xenial_default_3.4.113 fail to boot at next reboot. It's a lime2 Nand with SD card system, last rev hardware I don't find any solutions for the moment, because serial output doesn't output very much ... here is the 5.35 boot U-Boot SPL 2017.09-armbian (Nov 22 2017 - 15:21:35) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.09-armbian (Nov 22 2017 - 15:21:35 +0100) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Olimex A20-OLinuXino-LIME2-eMMC I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 *** Warni…

Hello, I am using nanoPi Neo Core with mini shield nanoPi NEO CORE/CORE2. The OS that i am using is Armbian stretch downloaded from this link : https://www.armbian.com/nanopi-neo/ The armbian image that I am using is : Armbian_5.65_Nanopineo_Debian_stretch_next_4.14.78 If I try to enable SPI without doing update and upgrade, it works. If I do update and upgrade and then try to activate SPI, it is not working. I dont find the spi device in /dev. Any idea what could be the problem? P.S: Before last week, I didn't have this problem. So I think it is related to a recent update done on this image. Thanks in advance. …

I have a question for more experienced users. Quite a long time ago I built an internet radio based on OrangePi Lite + DAC I think in the I2S interface with the module: PCM5102 ... PCM5102 DAC Decoder I2S -Aliexpress unfortunately the board broke down. I have another model, the aforementioned Pi 3 lts but it seems to be less supported. Can I connect the above-mentioned PCM5102 module to this model? Or maybe buy some other supported model that will work just as well as Pi lite with this DAC model or another? Ps. it would be nice if it had the ability to upload Armbian firmware to emmc flash memory I installed Armbian/Ubuntu on Pi3lts but I get some erro…

Hello! I'm running CB2 board as home server for a long time and after recent upgrade I've got an issue with LXC container. LXC container has "Ubuntu" inside and provides TOR functionalty + access point via connected USB wifi. USB adapter passed to container like this: lxc-wait -n tor -s RUNNING lxc-device -n tor add wlan0 I'm not using it recently, but recently I found, that after connection to AP nothing happens (no internet, DNS servers are IPV6 :)) and host system (CB2) is completely frozen. After reboot I've connected via SSH and retried to connect to access point - again freeze, and screen is populated with this: …

Today I updated my BananaPI M1 board, replaced the Bananian OS with Armbian Armbian_20.05.4_Bananapi_focal_current_5.4.45.img. I'm not getting the SATA with connected 1TB WD10JFCX working. The HD worked before with the Bananien kernel 3.4.x What can I do, how can I test, how can i get more information about the reason? The board is powered via the Micro USB and armbianmonitor reports DC-IN voltage > 5V

Armbian Jammy (Minimal CLI) boots/works fine from an SD Card. (Armbian_23.5.2_Nanopi-r1_jammy_current_6.1.30_minimal.img.xz) apt update && apt upgrade -y && apt autoremove apt install armbian-config -y armbian-install I choose option #2 - Boot from eMMC - System on eMMC Accept the warning. I choose option #1 - ext4 The install appears to move along smoothly. I choose the "Power Off" option. Pull the power, remove the SD Card. Reconnect the power. I never see the "heartbeat" on the "System"(red) LED. The NanoPi never boot or obtains an IP address.

Hi! Is it only me or there are no updates to packages? Let me explain, I'm running jessie server on A20 latest stable kernel and when I run apt-get update, apt-get upgrade there are never updates available. I have experienced this for some of the latest releases and now I'm starting to thing that something is wrong with my system. Especially because I have a raspberry pi and that (yes, I know is raspbian) is getting updates to packages from time to time. I haven't modified or customized anything in the sources list. And the thing is that I'm getting updates for firmware/kernel when they are available. Any ideas? Is it something normal for armbian (/debian)?

Hello. I have a problem with SPI interface I already tried to compile SPI interface as module in kernel config and then to turn it on, but what I get is: root@bananapi:~# modprobe -v spidev insmod /lib/modules/4.13.4-sunxi/kernel/drivers/spi/spidev.ko root@bananapi:~# lsmod | grep spidev spidev 16384 0 root@bananapi:~# dmesg | grep spidev *nothing* root@bananapi:~# ls /sys/class/spi_master/ spi32766 I found a topic about enabling SPI on Banana Pi Pro here. But after repeating same steps(I mean decompiling dtb, adding spidev and compiling it back) for Banana Pi M1 it doesn't boot any more. After U-boot the cursor blinks for about 10 seconds a…

Armbian_20.05.3_Orangepizero_buster_current_5.4.45.img apt install cryptsetup lvm2 thin-provisioning-tools All ok if install any two, size problem?

hello, my recent installation of armbian come to failure pretty quickly I was greeted after login by message, that kernel was updated and restart is required. So i did, but it never came up. Not sure if related to update, i didn't even knew armbian has autoupdates enabled. There is not much in uboot log - https://pastebin.com/zyc4WZpf possibly this: Wrong image format for "source" command SCRIPT FAILED: continuing... libfdt fdt_check_header(): FDT_ERR_BADMAGIC Should I increase logging level? MMC boot folder is found fine. My device setup Cubiraboard2 A20 #1 mmc uboot with /boot folder #2 sata h…

Who can share their valid /etc/apt/sources.list for an armhf SBC? Some past update has messed mine up a bit. Mine is: # deb http://gb.archive.ubuntu.com/ubuntu/ jammy main universe restricted multiverse deb [arch=armhf] http://ports.ubuntu.com/ubuntu-ports/ jammy main universe restricted multiverse # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. # deb http://archive.ubuntu.com/ubuntu/ jammy main restricted # deb-src http://archive.ubuntu.com/ubuntu/ jammy main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb [arch=armhf] http:…

Hi, I tried the instruction provided on topic http://forum.armbian.com/index.php/topic/1526-armbian-in-read-only-mode/?hl=overlayfs#entry11877 but I received kernel panic and the system doesn't boot any more. I mount the SD card on my laptop, I comment the line overlayroot="tmpfs" in /etc/overlayroot.conf and the system boot again. The package apt-get install overlayroot is not available. In installed it manualy from http://packages.ubuntu.com/en/xenial/overlayroot When I installed the package cryptsetup it return un error that cannot determine the root partition from /etc/fstab Please be so kind and write step by step instructions howto make the root file s…

Hi all, I've been struggling with the issue in the topic for a few days now. Actually the ideal solution would be a read-only root file system (with a writable overlayfs on top), so that I can just turn the power off, without risking any SD-card/filesystem corruption. There seems to be an easy solution for that according to this page: https://docs.armbian.com/User-Guide_Advanced-Features/ section "How to freeze your filesystem?". But the package "overlayroot" that is mentioned there does not seem to be available for Debian (Armbian Stretch). A quick attempt to adopt the overlayfs-startup scripts to Debian failed, because Debian is using systemd and the…

This is with standard Armbian Debian GNU/Linux 8 (jessie) 3.4.112-sun8i at the stock 1.296GHz CPU speed, and there is a fan+heatsink to stop overheating. I've disabled swap. # memtester 239 5 is OK, while # memtester 240 5 crashes out almost immediately: [10933.657662] Out of memory: Kill process 17061 (memtester) score 89 or sacrifice child [10933.657673] Killed process 17061 (memtester) total-vm:246992kB, anon-rss:245380kB, file-rss:28kB If I enable a small 32MB swap file, memtester seems to work fine up to 1200MB (still 750MB reported free, and no swap used) and crashes out for any larger values?? I'm getting the same out of memory problems trying to run the …

I would like to connect reed switch to OrangePi Zero with H2 processor. Can I use this? https://github.com/duxingkei33/orangepi_PC_gpio_pyH3 Under examples, there are two examples I think I could use: - read_button.py - read_key_PG7.py I have two questions. 1. Where is the pinout? read_button.py has this code: led = connector.gpio0p0 # This is the same as port.PH2 button = connector.gpio3p40 read_key_PG7.py has this code: led = connector.gpio1p38 # This is the same as port.PH2 button = connector.gpio1p40 #CHOW Which pins are which, where to get the picture of GPIO pins? (And why LED's…

As tkaiser would say, Lamobo-r1 has terrible design but the concept is good (multiple usage possible: network, misc services) But let's be honest, perfection is when you are dead. Like sleeping & coffee some weeks ago, I was wondering (right or wrong) if a DMA config for the lamobo-r1 GMAC would help the bandwidth issues. One CPU core is 100% with all the gazillions of interruptions to handle. Now the DMA for A20 is in the mainline kernel but I am missing some tech glue. I have read an example in the kernel 4.3 doc with DMA config (DTS) for DWMAC (*if* applicable, not only for STMMAC, but also for A20-GMAC ???) links: stmmac kernel 4.3 documentation d…

I know it's not an officially supported board, but it's been working really well so far, so I'll give it a shot. Today I updated my kernel to 5.9.0-sunxi (coming from 5.9.0-rc7-sunxi) and after rebooting the (wired) network was dead. Everything looked fine, ethernet driver is loaded, interfaces were up and had IP addresses, but packets were not being sent. Pinging anything but the Banana Pi itself says "destination host unreachable". Routes were set and looked correct - even tho they should not even be necessary as I was pinging the gateway. tcpdump on eth0 showed nothing at all, almost as if the kernel doesn't know where to send the packets. Anyon…

Hello, friends. I am using legacy Armbian 3.x kernel on my development boards where I run Stella emulator with some special USB joystick. The joystick is detected as XBOX controller, hence I guess it uses xpad driver. The problem is that this driver is not present in the latest Armbian so this joystick does not work. I would like to use latest Armbian to have the latest packages, using it as a print/scan/radio server and would like also to play some Atari game from time to time. I tried to build it from the source using this https://github.com/paroj/xpad I can load it with modprobe, the joystick seems to be detected, but it is not working in Stella, I cannot eve…

Hi all, I recently bought a Banana BPI M2 Zero for a personal human-machine interaction project as this was the only (cheap) available option w.r.t. my specs (HDMI, entry-level OpenGL GPU, enough CPU power for the task). I got a version with Allwinner H3 (which in my view is good) and also read through the H3 buyer's guide. According to that guide, the CPU should be sourced by 1.3V, but to my (positive) surprise, I measured only 1.15V at the output coil (after the coil and against GND, of course) of the SY8113 regulator. However, there's certainly something not working as expected from the schematics: both, the SY8113 and the SY8089 1.2V regulators (SYSTEM+CPU…

Hello! I'm trying to make image for olinuxino lime A10. Prebuild image does not have /dev/uinput and /dev/hidraw for my touchscreen, and built without CONFIG_DRM_KMS_HELPER, so i can't replace broken EDID for my HDMI display. A month ago i succesfully build ubuntu image with uinput and hidraw support. But now - i need to rebuild it again, but kernel compilation fails with this error: LD drivers/media/usb/built-in.o LD drivers/media/built-in.o make: *** [drivers] Error 2 [ error ] Kernel was not built [ @host ] And I don't know where to find error description. The last error was missing libssl-dev. Regards.

Issue found! Orange PI changed eMMC from KLM8G1GETF to KLM8G1WEPD. The difference is eMMC 5.0 vs 5.1 and maybe more. The key things is that Armbian (checked using 5.35 and the latest one) does not see this memory (fdisk -l)!! I have noticed it on OPI0 Plus 2 H3. PCB boards are the same, only memory model no. difference. Someone solved it or noticed the same? Confused 🤨

Bonjour, je viens d'acquerir une opi win plus j'ai téléchargé et installé sur une carte scandisk ultra 32gb et au boot j'ai le message can not setup simplefb node not found l'image utilisée est Armbian_5.32.170705_Orangepiwin_Ubuntu_xenial_dev_4.11.8.img. Need help tks

Today I was going through my cupboard and did find a original pcDuino (v1) with A10-CPU and 1GB of Ram. In my mind I got the pcDuino v2 download-page of armbian. As JohnGo did wrote May 2016 on this page is a picture of the pcDuino v1: So I checked the specifications v1 <--> v2 and found ony that v2 has only a WiFi-Board soldered where on the v1 is a additionally USB-Port. Also the v1 is missing the Arduino-Headers, but has some other pin-rows for GPIO and so on. CPU (single-Core 1Ghz) and Ram (whopping 1GB for 2012) is the same I wrote the pcDuino v2 Image to a uSD and booted it without problems. (and changed /etc/upd…

I'm running what I believe is the latest experimental for the neo2 - 5.27.170601. This could well be a problem related to something that doesn't yet work in this build. I've built strongswan on the neo and everything built fine and installed. ipsec starts and I'm able to bring a tunnel up to a remote vpn server that I know is fine and is verified working from some other box with identical connection and key configuration that I'm using on the neo2. When the tunnel is brought up on the neo2 it seems I'm not able to get any traffic to flow i.e. curl api.ipify.org should return the public ip of the remote vpn server but it just hangs. When the tunnel…

Hi, just installed Armbian 5.38 mainline (both debian server or Ubuntu server fresh installation). There are two processs eating cpu (kworker), and I read some other users have the same issue, but there is a solution? Other problem: I use this board with Bluetooth dongle to monitor my solar plant. Sometimes Bluetooth dongle disappear from lsusb or hcitool scan tell me device is busy with no reason, just unplug and reconnect usb dongle and all restart to work again (tried with two different Bluetooth dongle, this dongle works with no problem at all in another orange pi pc, no disconnection or disappear). The pow…

I am using Orange PI PC for running a Deluge (torrents) and FTP server. I have noticed that when Deluge is downloading something, the RAM is getting filled up. At some point the kswapd0 kicks in and start using 100% of one CPU core. This is going on until I manually release the memory, eather with reboot or with "echo 1 > /proc/sys/vm/drop_caches". Here you can see kswapd0 with "top": However, the kswapd0 is not visible on htop, but it shows one core at 100%. The memory usage is 111 MB. But "free -m" command shows that 865 MB of memory is used.

I need to run btrfs for a headless web server on an Opi PC. The armbian 3.4 kernel btrfs is too green to be used. I was able to install the 4.7.3 kernel (and remove the 3.4.x) using apt. I got btrfs and support for some USB devices, but lost HDMI and 3 cpu cores. Is there a better option I could try? This board seems to be running like a champ with just one core but I would like to have it fire on all 4 and have at least some video output if I wanted to. Is it ok to ask for recomends as to what board I might better choose? I require a modern Ubuntu/kernel, decent usb, decent network (gigabit if possible), and low cost. They will be used for personal cloud an…

I'm trying to check if UART on my Orange PI is working. I've enabled UART via armbian-config and rebooted OPi. root@orangepipc:~# dmesg|grep tty [ 0.000000] Kernel command line: root=UUID=e5185d19-ff08-47bb-8673-1779ef917d92 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=530c2b83-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 [ 0.000189] console [tty1] enabled [ 1.975487] console [ttyS0] disabled [ 1.995…

Hello all, I am very excited to install armbian debian jessie on my cubietruck ! I managed to get the Armbian_5.31_Cubietruck_Debian_jessie_next_4.11.5.img to an SD card, plugged it in, switched it on and everything went perfectly fine! Great! Now, I am trying to get this OS on the CT Nand. Sadly, the nand-sata-install doesn't work, returning the message : "There are no targets. Please check your drives". One very strange thing to me is the output of the /proc/partitions files that shows the following : major minor #blocks name 1 0 4096 ram0 1 1 4096 ram1 1 2 4096 ram2 …

Hi after half a year using orangepi PC have upgraded system and it hangs when compiling headers.... After that have to reformat sd card and installed last version of armbian and the problem still remain when try to upgrade it... fresh system... đ then apt-get update root@orangepipc:~# clear root@orangepipc:~# apt-get update Hit:1 http://ports.ubuntu.com xenial InRelease Get:2 http://ports.ubuntu.com xenial-security InRelease [102 kB] Get:3 http://ports.ubuntu.com xenial-updates InRelease [102 kB] Get:4 http://apt.armbian.com xenial InRelease [14.1 kB] Get:5 http://ports.ubuntu.com xenial-b…

4.14.65-sunxi on an Orange Pi Zero. Trying to set the i2c bus speed to 400kHz using the following dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { clock-frequency = <400000>; }; }; }; Which produces: Error: dtc does not support compiling overlays Please try to install matching kernel headers Installed linux-headers-next-sunxi and still getting the same thing. Device tree compiler version: DTC 1.4.2. What am I doing wrong? Spoiler

Hi! I have recently installed Armbian 4.5 (Debain Jessie and Ubuntu trusty) at Banana Pi M2, and I’ve noticed that the computer doesn’t reboot after the command. It simply switches off, and the red diode lights up. How it could be corrected?

hi guys sorry for simple questions , i installed Armbian_5.91_Bananapi_Debian_buster_next_4.19.59.7z on banana pi M1 , after login i try to statx for have desktop but not start , tell me not found , i try to search in google but not find nothing about this , i saw all tutorial start automatically the desktop enviroments, is possible install ?? or exist a guide?? thankz and sorry agin for simple questions

Hi, I am developing application that will show graphics in console mode using frame buffer access in system with Orange Pi PC board. Several Debian images I tried until now from Orange Pi downloads always set up 32bpp frame buffer. Calling 'fbset -depth 16' causes screen corruption. Changing script.bin setting (fb0_format = 5) did no change. Any suggestion?

I just recently acquired a few Orange Pi Zero Plus 2 boards. I need to get them working for a Bluetooth application. After a somewhat rough start with the WiFi they appear to be running smoothly now. The first problem I am noticing is that sata-nand-install does not exist on the distribution for the H5. Can anyone shed some light on what is necessary to get these boards to boot from eMMC? Is there anyone currently working on this problem? If not, what is the correct version of that script that I should download to begin trying to port it, and what utilities will I need to adapt to make it happen? Any advice on how to begin? On another front, doe…

Hello, guys, has anyone ever faced issues with SPI controller on BananaPi M2 ? I am having a weird issue which is confirmed by at least 2 peripherals: Waveshare 3.5 LCD and NRF24 wireless chip. The data incoming from MISO is always shifted by 1 bit to the left. , i.e. reading STATUS register of NRF24 gives 0x1C instead of expected value 0xE. The same story with other registers. Saleae logic analyzer is always showing correct pictures !!! See attached image as an example of reading STATUS register from NRF24: master is sending 0x07 and receiving 0x0E (14). I have tweaked byte rate and other parameters - no result. I have finally tried to connect using…

Thanks for your effort on this project. Much appreciated. I was able to follow this tutorial (10 minutes, 24 seconds in) on the Debian image to get the TV out working. I'm building scripts to modify the networking between a number of modes - super helpful to get a console access when I break something and lose all networking access. Is there support for this on the Ubuntu side? The simple "add 'tv' to the bottom of "/etc/modules" doesn't do anything. Please advise. Thanks!

wget https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.6.6.tar.xz tar -xpJf linux-4.6.6.tar.xz ln -s linux-4.6.6 linux make oldconfig make menuconfig make-kpkg clean CONCURENCY_LEVEL=3 fakeroot make-kpkg --initrd --revision=14082016.01 kernel_image kernel_headers But USB do not work! I do not found CONFIG_AXP20X_POWER in new config. After manual add its gone! How to solve this ?????

Hello friends, I found these cameras for Orange Pi: https://www.aliexpress.com/item/Orange-Pi-Open-source-IP-Camera-with-wide-angle-lens-Smart-Home-Control-Device-for-PC/32652476606.html https://www.aliexpress.com/item/2MP-Camera-module-for-Orange-Pi-PC-Zero-One-PC-Plus-Plus2-Plus2e-Zero-Plus-2/32833966539.html Can it work directly with Orange Pi Zero Plus2-h3? Or is there any difference with h5? Do you know how many fps with which resolution does this camera have? Thanks.

I have tried a few different suggestions that I have seen online to implement wifi on Orange PC with a wifi dongle. However, none them can work reliably. OrangePi zero works but wifi speed is very slow (about 1-2Mbps). I recently tried using Raspberry Pi with wifi dongles. It is almost plug and play and very reliable. I hope there is a way to do the same on OPi. If anybody know one, please let me know. I will be happy to try it out and report back.

hi guys, I have reported this on to etcher folks at https://github.com/resin-io/etcher/issues/1466 Not sure if it's a feature or a bug. Cubie truck 3 Any ideas? Etcher version: Etcher-1.0.0-win32-x64.exe Operating system and architecture: windows 8 Image flashed: https://dl.armbian.com/cubietruck/archive/Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113_desktop.7z Do you see any meaningful error information in the DevTools? Filesystem Size Used Avail Use% Mounted on udev 941M 0 941M 0% /dev tmpfs 189M 5.5M 184M …

Hi all, I'm new here. Since I bought my OPi One I didn't try any of the official images, but only armbian legacy kernel. The first OPi one I thought it was broken, no led on the board only the eth ones, nothing happend on the screen (homemade power cable with 1.4 plug and a xiaomi ac power adapter 5V 2A almost correctly given, tested with a multimeter). The image was burned on a 4gb kingston micro sd card with etcher formatted with sd formatter. So I bought another one, and I have the same identical issue. So, I started to study and I found out that I could connect to the OPi through SSH. So it what I tried to do all the night. Again image burned with e…

I have a BPI-M2 and I am trying to patch kernel 4.4.1 with contents of archive patches-4.4.1-rt6.tar.gz for RT-Preempt while making Debian Wheezy xfce desktop image. I have tried putting patches in /userpatches/kernel/sunxi-dev and /userpatches/kernel/sunxi-dev/linux-vanilla/v4.4.1 nether worked. Made image but patches were not applied Any help would be appreciated Tim

Whats the suitable image for Orange Pi PC H3 Quad-core ( https://www.banggood.com/Orange-Pi-PC-H3-Quad-core-Learning-Development-Board-p-1010455.html )? Thank you!

Hello. Has anybody tried to encode h264 on h5 via ffmpeg cedrus264? any help would be appropriated. thanks in advnace.

Hello Community, Now I encountered the following problem when testing my "orange pi zero plus": I tested the processor load (stress-ng) at a working frequency of 624mhz for 25 minutes. Settings: mainline sunxi64-next (4.14.y) Spoiler armbianmonitor -m 10:53:44: 624MHz 4.50 100% 0% 99% 0% 0% 0% 100.1°C 1/1 [ 3314.299373] thermal thermal_zone0: critical temperature reached (105 n Message from syslogd@localhost at Dec 3 10:53:51 ... kernel: [ 3314.299373] thermal thermal_zone0: critical temperature reached (105 C), shutting down Stopp…

Hello. I have the following problem with my Orange Pi PC: When I turn it on, only the green and orange LEDs of the ethernet port are flashing. There is no output on the HDMI port. I have already tried different microSD cards and different images. It used to work perfectly, but all of a sudden it stopped working. Maybe an issue with the power supply (it is the offical power supply 5V 3A DC jack).

Hi All, I am looking for h3consumption utility to change ddr freq (I want to set ddr and processor as low as possible) Could someone help me ? Best Regards, Boris

Hi guys, I've been having problems on my NanoPi Duo implementing a music streaming service using Alsa PCM to output the audio. When calling snd_pcm_open with the nonblock flag set, I had snd_pcm_writei returning a broken pipe error several times per day (when continuously playing). I noticed not setting this flag and, thus, allowing snd_pcm_writei to block until there was enough room in the Alsa PCM buffer, did not show this problem. This was however unusable because the blocking behaviour slowed down the rest of the software enough to be annoying. I think I solved it now by checking with snd_pcm_avail_update if there's enough room available, …

Hello , How do I get RTC working on Banana Pro. I think I have 2 options 1. Built in one 2. External [DS3231] Here is some info about the setup i got. dmesg | grep -i rtc [ 1.928725] sunxi-rtc sunxi-rtc: Warning: RTC time is wrong! [ 1.934023] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 hwclock --test -D hwclock from util-linux 2.27.1 Using the /dev interface to the clock. Last drift adjustment done at 1506000286 seconds after 1969 Last calibration done at 1506000286 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... select() to /d…

OrangePi PC Armbian 5.35 with LXDE desktop Firefox 57.0.1 I haven't done anything with my OPi for 6 months, so when I tried it again, it booted normally except for not looking quite right on my big HDMI screen. I remember fiddling with this in the old immediate-post-boot phase, but http://armbian.com says to use "sudo armbian-config". There were 250 MB of updates, which took forever. Meanwhile I tried to run Firefox, which repeatedly crashed on startup. Installing v61.0.1 didn't help. Also Konqueror, but not Dillo or Midori or Chromium-browser. Back to fixing the display, I tried running it but didn't have the armbian-config, so I downlo…

Hello everyone. I encourage you to write these lines after I spend all day reading and trying to solve the problem without success. Knowing that there are other many post about, I write this new that existing ones are already very old and refer to applications and concepts that no longer exist in the latest versions of ARMbian. The fact is that I bought a new OrangePi Lite with a new SDHC Clase10 (80MBs) SanDisk and basically not I connect to the WIFI 2.4 g connection of my house where work perfectly without any problems other Zero OPI and OPI PC + with ARMbian 5.35 Ubuntu. The summary problem is it asks me again the password and does n…

I was able to upgrade Armbian to 18.04 bionic beaver on my Banana Pi M1, and it's working (almost) fine! I used the command to update the sources.list to bionic: apt update && apt dist-upgrade -y && apt autoremove -y && apt autoclean apt install update-manager-core do-release-upgrade -d Fetched 403 MB in 8min 43s (769 kB/s) I gave "yes to all" to almost everything, except on replacing config files like KEYMAP, sshd and bind All these services I use are working correctly: network, SSH, bind, mail, cups, minidlna, SATA, USB printer, Samba This is not working: qbittorrent-nox 4.0.4 (misses libboost-s…

Hi, I have Cubieboard with armbian. ARMBIAN 5.36 user-built Ubuntu 16.04.3 LTS 3.4.113-sun7i # apt-get upgrade Setting up linux-firmware (1.157.14) ... ln: failed to create hard link '/boot/initrd.img-3.4.113-sun7i.dpkg-bak' => '/boot/initrd.img-3.4.113-sun7i': Operation not permitted update-initramfs: Generating /boot/initrd.img-3.4.113-sun7i gzip: stdout: No space left on device root@cubietruck:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/nand1 32M 24M 8.6M 74% /boot Can you advise me something to solve this issue? Thank you.

I just bought an orange pi pc and i want to hook it up to an old pc monitor i had laying around. The monitor requires 60 Hz and a resolution of 1024x1280, it uses a vga port. Is there any way to get this to work? Regards AcidWizard

Hi, I'm here to dig into low power consumption with allwinner H6 boards, I own an OrangePi one plus and I'm already doing some tests. With an H3 board and legacy kernel I would simply tweak fex file to turn off the unnecessary, and there is already good material around this argument. But with mainline kernel there is no documentation about lowering power consumption. I would really appreciate some hints on how to tweak down consumption for H6 boards and mainline kernel, probably editing DT overlay or some other config/patch files, and re-building? I already tweaked the simplest things like: -Using fast ethernet instead of gigabit -Lowering max CPU frequency (…

I found that it is not easy to use the Dallas one-wire temperature sensors and the composite TV-Out on the Banana Pi with the current Armbian version. I have searched for posts on these topics in the forum. The posts that I have found in this forum describe solutions for outdated Armbian versions or do not give enough detail. The following posts in this thread will describe how to solve these problems for the current Armbian version for the Banana Pi M1.

Hi, I would like to use wiringPi for my NanoPi Neo Air, but after installing wiring P, I only get unable to determine board revision as output from gpio readall. I tried this approaches already: Could someone please explain me how to build wiring P for NanoPi Neo Air so that it is working? On NanoPi Neo Plus 2, I did not have to change anything when installing wiringNP under Armbian.

Hello, I've been running Armbian for a while on an Orange Pi Zero without any issue. Every now and then I perform an apt update && apt dist-upgrade on that board but today the upgrade process failed with the following error and I'm not sure how to fix it. renaud@AnetA8:~$ sudo apt update && sudo apt dist-upgrade -y Hit:1 http://ports.ubuntu.com focal InRelease Hit:2 http://ports.ubuntu.com focal-security InRelease Hit:3 http://ports.ubuntu.com focal-updates InRelease Hit:4 http://ports.ubuntu.com focal-backports InRelease Hit:5 http://armbian.hosthatch.com/apt focal InRelease Reading package lists... Done Building dependency tree Readin…

I use armbian 5.16 or 5.17 on my OPI-PC (I do not remember which of the two, I read Firmware: #14 from OPI-monitor). I installed h3consumption tool a few days ago with these instructions: sudo -s wget -q -O /usr/local/bin/h3consumption "https://raw.githubusercontent.com/igorpecovnik/lib/master/scripts/h3consumption" chmod 755 /usr/local/bin/h3consumption then I used "h3consumption - g off" and after a reboot "h3consumption - e off" (because I use a USB3toGigabit ethernet adapter). Now I have: $ sudo h3consumption -p Active settings: cpu 1296 mhz allowed, 1200 mhz possible, 4 cores active dram 624 mhz hdmi/gpu off usb ports active eth…

Hello, I'm newbie with linux and the Cubietruck. What is the difference between the version Wheesy, Jessy and Trusty ? Thanks François

Hi Guys, is there a plan to build a version for the Allwinner A80 boards? I have a Tronsamt Draco AW80 http://www.tronsmart.com/products/tronsmart-draco-aw80-meta.html, and want to use Debian on it. But they don't have any Debian Version to download, only Ubuntu. best regrads Roland

hello there! after update rpimonitor to 2.13-beta6 by Xavier Berger, can't monitor, any temperature , memory usage. But CPU freq, Sd card and network work OK. my spec : Orange pi pc + ARMBIAN 5.38 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i

Out of curiosity, and according to several articles/posts including this one http://forum.lemaker.org/thread-1847-1-1.html the A20 has support for hardware watchdogs. Has some successfully configured and used the watchdog kernel module sunxi_wdt.ko in a banana / lamobo R1?

Hi. Please help me to understand how hardware encoding works in nanopi with H3 chipset. I have newest version of armbianos: cedrus and related modules is loaded by kernel There are following hardware acceleration methods and encoders Please explain me what i am doing wrong here : and here: Thanks a lot.

Hello. Can't run x11 on Debian 11. I am using Nano Pi AIR (Allwiner h3). Since the board is not officially supported, I built the image on debian 11 myself. root@nanopiair:/# uname -a Linux nanopiair 5.15.44-sunxi #trunk SMP Wed Jun 8 08:41:04 UTC 2022 armv7l GNU/Linux The LCD is connected via SPI, chip is ili9486. Device tree file has been created, I can see the loading process and the console on the screen. I'm trying to start the X-server by "startx" from ssh session, but for some reason it ends immediately after the start. I tried using fbdev or fbturbo as driver. I also tried to remove the config with the driver in general (section "Devi…

Hello. Good day. I'm trying to use the SPI on a OragenPI One Plus (Allwinner H6), and, although I have enable it via the /boot/armbianEnv.txt configuration, communication is not working. Here's the armbianEnv.txt armbian@orangepioneplus:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun50i-h6 rootdev=UUID=19c1886e-0b74-45b8-b9f5-5fbd4bdeb5c2 rootfstype=ext4 overlays=spi-spidev param_spidev_spi_bus=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u And here's the SPI device listed under /dev armbian@orangepioneplus:~$ ls -la /dev/sp* crw------- 1 root root 153, 0 nov 28 15:…

In this post tkaiser says disabling HDMI and the GPU on H3 boards can reduce power consumption by 200mW. Is it possible to do this on a headless Orange Pi Zero 2+ H5? I don't believe I can use h3consumption or edit FEX files because I'm on the H5 mainline kernel. I tried setting monitor=none in armbianEnv.txt, but I didn't notice any appreciable difference using an inline USB power meter.

Hello all, The board has a 2MB NOR FLASH chip what would be enough for storing u-boot and booting the system over network. Unfortunately u-boot says there is no ethernet. Is there anybody who knows how to enable ethernet on this or similar board like OPi PC2 or Nanopi NEO2? Is it just a matter of configuration or is RTL8211E as PHY generally not supported on H5 chips? Thank you very much for your help. --DieHackbeere

I experencing the following error upgrading orangePI-PC with connected a WiFi ralink key: # apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-firmware 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 1,617 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue? [Y/n] Y Get:1 http://apt.armbian.com/ jessie/main armbian-firmware armhf 5.25 [1,617 kB] Fetched 1,617 kB in 11s (138 kB/s) …

I have tried 3 Orange Pi 3 images on my orange Pi 3 LTS. None of them will mount the root fs and continue booting. It shows btrfs, but the partition is ext4 and the armbianEnv.txt file has the correct UUID and ext4 stated. I can boot an image from the OrangePi website, so I am 99% certain it is not the power supply or sd card.

Hi, I'm running the following kernel on my Orange Pi Lite: Linux lights 5.3.9-sunxi #19.11.3 SMP Mon Nov 18 18:49:43 CET 2019 armv7l GNU/Linux I'm getting the following crash in the WiFi driver (copy-pasted from dmesg) after some time (about 10 hours if I read the output correctly?). [36792.103947] ------------[ cut here ]------------ [36792.104326] WARNING: CPU: 3 PID: 1108 at drivers/net/wireless/realtek/rtl8189fs/core/rtw_mlme.c:2622 rtw_stadel_event_callback+0x41/0x1fa [8189fs] [36792.104331] Modules linked in: snd_soc_hdmi_codec snd_soc_simple_card snd_soc_simple_card_utils sun8i_codec_analog sun4i_i2s sunxi_cir sun8i_adda_pr_regmap snd_…

Dear All, I get frequent and random disconnection from orangepizero3 onboard wifi with armibian community (self-built) both trunk and 24.02 current kernel, 6.6.26 and 6.6.28 message is always [21738.338021] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21848.116072] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21915.426734] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection sm_state (5), status: (2)! [21915.426817] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection Vodafone-CSC failed status code:1! [21919.477424] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share …