Allwinner sunxi

Hello ! I am use A20-OLinuXino-MICRO-e4GB Debian server image with mainline kernel work fine with eMMC, but I need eMMC support in Ubuntu desktop with legacy kernel. How I can do it ? Sorry for bad English :-) I hope, you understood me :-). Thank !

I am running cubitruck wheezy 7.5 from 2014, Kernel 3.4.104 for over three years as homeserver with VGA display. How can I activate HDMI for a new display. (I cannot reinsall the whole system, growed up for all the years) I already changed the settings in fexfile: [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 3 screen0_output_mode = 6 screen1_output_type = 3 screen1_output_mode = 6 also changed fex to bin and reboot, but no HDMI-output Can anybode give me a hint?

HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

SBC is banana pi M1 I tried the banana pi at church today, things went great as for the Libreoffice impress presentations but it was hard to navigate to menus because the banana's resolution was set to 1920X1080p. Everything was too small in the projector, we need something like 1280X1024 or 800X600. I tried `a10disp changehdmimodeforce 4` to change it to 720P, on the projector but display became unstable and I had to reboot to get it back. We have two modes for projector, VGA (HDMI->VGA converter cable) or plain HDMI. Today I tried the VGA but we can also do HDMI. Please help. Thanks.

Hello, I use the BananaPi M1 as network bridge with tranparent http proxy and filter with 2nd ethernet (USB adapter with AX88179 Gigabit Ethernet). But since latest update with kernel update, the network seemce to be go down often or the sytem is going bad. I can't find any solution and need some help. If you need some more information, please tell me what I should send. Thank you! Edit: The system is stuck on reboot... have to put of the power.

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Hello, I'm following this project : I was recently spending time on the activities to do with children, 3D printing and robotics, and in order to be able to try to follow https://docs.armbian.com/Developer-Guide_Build-Preparation/ i have bought a new laptop which respect the requirements (SSD, ram...). So now my next goal is to try to make a custom version of armbian dedicated to the schools. To start, for the first step, I would like to try make a localized version of armbian in French by default, in order to be more easier for the French speaking user. With the new evolutions of armbian for OrangePiPC+, there is an ubuntu…

Hello. I install the 5.35 Version on a OrangePiPc+, all run in good condition. I upgrade to the 5.38 without problem (kernel 3.x) I upgrade the kernel to 4.x, so long as i didn't reboot, all is in function (with Ubuntu) and my USB Tevii 662 is recognized (and run with TVHeadend). After reboot, no Ethernet and no USB, no possibility to login. I tried all versions with kernel 4.x, even desktop, no function. Anyone has a idea, how it will be run??? Thank's for any idea. P.S. OrangePI PC Plus, 1 GB RAM, 8 GB SSD-OnChip, Tevii S662 S2 USB, TVHeadend.

Hi all, can some kind soul tell me if this update will break my cubieboard installation? (I know that cubieboard a10 is no longer supported, nevertheless maybe someone can tell me after 5 seconds of thinking "yes" or "no" :)). XXXXX@cubieboard:/etc/apt/apt.conf.d$ apt-get -s -t stretch install dnsmasq NOTE: This is only a simulation! apt-get needs root privileges for real execution. Keep also in mind that locking is deactivated, so don't depend on the relevance to the real current situation! Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be instal…

Hello ! I know that there are already topic talking about that, but they didn't helped me. I have Armbian 5.38 Desktop. I plugged the camera, and I think it's on the right side: I followed instruction of Garlic here: Nevertheless, with motion I get a grey screen telling me that the camera is undetected: I noticed a very small impact on the cable after the delivery of the camera, but because it is very small, I don't think it's the cause. I don't understand, and any help is welcome. Thank you !

Hi all, I have an application running on an orange pi pc plus 2 over the emmc 8gb memory. Everything is in there (os, db sw) and what it does is acquiring data from some sensors and then pushing it over mqtt to a server. Now, due to frequent internet connection issues, the board is able to store up to ~ 1 month of data in a local db but this means quite a lot of writes per seconds (plus all the logs). I would like to have an idea of how much the emmc can keep up with this rates and thus I am trying to understand how to calculate the life span in years (hopefully nothing less). Can anyone help me on how to do that? I am using right …

Hello. this is my first post. I was looking through the forum but I did not find a similar problem. About power supply - until now I did not have any problems, I use a computer power supply. After a few months of non-use of my device, I downloaded an updated, latest version (Armbian_5.38_Lime2_Ubuntu_xenial_default_3.4.113_desktop) to an old, previously functioning card. When I connected the device, it did not turn on. I tried to turn it on manually, but nothing happened except the short flash on the connected mouse. A while ago, I uploaded an older desktop version to NAND. I used the sd card to start up. Is it possible that this older version loaded on NAND c…

http://ix.io/NWB Hi, above i posted armbianmonitor -u out. I tried dettaching usb disk due errors in btrfs for continuos recording, disk was mounted in ro mode. Now, with only microsd happen same thing, no btrfs errors obviusly, but orangepi plus 2e go down time to time, light are on, but don't have ssh access or ping. Please someone could show some light in it, thank you. Edit: sorry, I forget say my wlan config is make in plain /etc/network/interfaces, with fixed IP, the SBC work fine up to go down.

I'm trying to follow this tutorial here https://www.pyimagesearch.com/2015/07/27/installing-opencv-3-0-for-both-python-2-7-and-python-3-on-your-raspberry-pi-2/ but nothing I do works when I get to install numpy, opencv, or darknet. When I try to build OpenCV following default instructions (or any for that matter) I get: don't know what to do and there's nothing online that helps me out. the only thing that worked was apt-get install python-opencv but it installs a very old version which I can't use for my project. Also when I try to make darknet I get:

1. Orange pi pc cant shut down ,remains blink. 2. Cant eject usb /sda file directory not available. 3.funny with much updates still cant connect to Internet with clearing block interfaces from armbian config.

Hello, I have decided to try out Ubuntu 16.04 legacy on my original banana pi for the first time and to my surprise the first problem I noticed is that the usb ports weren't working at all. I tried two keyboards which are working fine on all my Linux computers all running on mint 18.3 (logiItech k360, and insignia nsc5011-c) they are both wireless keyboard + mouse combos they did not work at all on the banana. I previously had bananian on it prior to today and all usb ports were working fine as I was able to connect external usb hard drives to it. I decided to connect the banana to my LAN and ssh to it from my laptop, did an apt update…

I am building armbian with mainline kernel (4.14.19) on jessie for OrangePi Lite... Sometimes on booting my Pi Lite, the wifi does not work. I cannot create hotspot and connecting to existing networks will not work. A short time after booting I see the following messages in the dmesg log [ 102.077151] sunxi-mmc 1c10000.mmc: send stop command failed [ 102.077184] sunxi-mmc 1c10000.mmc: data error, sending stop command If I remove and reload the 8189fs module I will see the following error in the dmesg log [ 572.371452] rtl8189fs: probe of mmc1:0001:1 failed with error -110 If I don't see the mmc errors after startup (say 5 minutes) the w…

Unfortunately I don't have a USB keyboard or USB UART cable around... is it possible to compile an image that has my wifi information baked in?

Hi, I was wondering if anyone was having issues with the ethernet port using the legacy kernel ? It does seem to kind of work ... it will get DHCP from the router and configure the routing tables etc but after that it goes wonky. When I do a ping test from the router I get "50/50 transmitted, 15/50 received, 70% loss". A ping test from the opi-win to the router gets a similar result. If I try a ping/ssh from a PC connected to the router I get a 95% packet loss Everything else seems to work fine ... HDMI, USB, WiFi (AP/STA modes) which is really, really nice. Thanks TB

Hello, i have a old Banana Pi M2 with the current Armbian in use. I use the green LED with Heartbeat Signal. Today i try to connect with putty but after Username and PW nothing happen. Samba Service work normal. Then i have look at the Banana and the green LED was lightning constant and no heartbeat blinking. Maybe the trouble was because in a few meters distance sawed with a circular saw. Has perhaps caused interference or power fluctuations. No idea and maybe just coincidence. I have been using Armbian for only two days. Previously, the manufacturers ran Distribution for two years. I have Google and found out t…

Please help me build driver for usb wifi adapter Tenda u12 (RTL8812AU chip). Board Orange Pi+2 (Armbian OS https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z) adapter driver link http://tendacn.com/en/download/detail-2863.html build log with error Spoiler root@orangepiplus:/home/alex/Desktop/RTL8812AU_linux_v5.1.5_19247.20160830# sudo sh ./install.sh ################################################## Realtek Wi-Fi driver Auto installation script Novembor, 21 2011 v1.1.0 ################################################## Decompress the driver source t…

Hi I want to install some packages, but it not found on sources. When i do update repositories by sudo apt update command, the following messages shown that means the repositories is broken. Err:1 http://httpredir.debian.org/debian stretch InRelease Could not resolve 'httpredir.debian.org' Err:2 http://httpredir.debian.org/debian stretch-updates InRelease Could not resolve 'httpredir.debian.org' Err:3 http://httpredir.debian.org/debian stretch-backports InRelease Could not resolve 'httpredir.debian.org' Err:4 http://security.debian.org stretch/updates InRelease Could not resolve 'security.debian.org' Err:5 http://apt.armbian.com stretch InRelease Could …

I'm trying to get a 4K 5.5" LCD to work (only console mode needed ) . U-boot can get it on at the desired resolution : 2160x3840 ( yes it's a portrait mode ) and display correctly . Seems that U-boot is reporting the correct information to set up simpleFB , but I don't get any display after kernel loading . The display adapter (HDMI>MIPI) have 3 options ( switching between 3 different EDID ) , the 2 others are working correctly ( 1080x1920 , 1440x2560 ) . I 'm wondering if this is related to simpleFB limitation , or memory allocation ... problem is that I'm a complete noob ... I can provide any information needed as long as you tell me what…

Hey. I got an orange pi zero + 2 that I'm trying to run armbian on. I've downloaded the both the ubuntu and debian server, and installed to the sd card using Etcher. It boots, but when the boot process reaches "starting kernel", it reboots, and keeps in that loop. Here's a link to a screenshot of what's shown on screen just before it reboots: https://www.dropbox.com/s/xt6ebsdzi0nkf19/Fil 19-02-2018 18.12.04.jpeg?dl=0 I've also tried the images listed on orange pi's own website. They boot up fine to a working desktop. Any help?

Hi, I tried two builds for my OPI Zero. Armbian_5.35_Orangepizero_Debian_jessie_next_4.13.16.7z Wifi works but no audio. (and instabel ethernet connect) Armbian_5.35_Orangepione_Ubuntu_xenial_default_3.4.113.7z Audio works but no WiFi In witch build works both ?

I'am running a PiOne with 4.14.14 Stretch. I have installed acpid and give the command acpi_listen When pussing the button in Stretch and I didn't see any logging. With the old kernel in 5.38 Jessie on the same PiOne I saw button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 In the output of dtc /boot/dtb/sun8i-h3-orangepi-one.dtb I saw key_pins@0 { pins = "PL3"; function = "gpio_in"; linux,phandle = <0x39>; phandle = <0x39>; }; Means gpio_in defined as an input? Is the button function not yet implemented in 4.14.14? Or is something going wrong?

Hi every body, I have a Orangepi Plus 2E as you know with 16GB eMMC. Have installed armbian via SDCard before and executed nand-sata-install to copy it to eMMC. But currently need to get an image to install on another one. So there must be an opposite action like install_to_sdcard (in raspbian) but I couldn't find it.

Hi I've downloaded v5.38 firmware for my Cubietruck device and replaced on an older version due to my problem with new updates. Etcher was my tool for writing image on SD card and i have cleared SD card before writing new image. When new image installed and device booted up, but WiFi is not working and WiFi module is neither listed in lsmodule output nor module list file. It seems that WiFi driver is not installed or WiFi hardware is not detected. Is there any way to fix this issue? @Igor

Hi there, I'm trying to run luma.examples using an SSD1322 display via an SPI interface. I think I got the wiring right but the software is responding with errors. The app is expecting D/C and RESET parameter via a GPIO pin numbers to control the display.. I'm not sure how the Nano PI NEO Air physical pins are mapped to a GPIO port under Armbian. Where can I get a list of mappings for the physical pins to the GPIO pin numbers? How does this work? Is this an OS specific thing? Thanks in advance. PS: `uname -a` : Linux nanopiair 4.14.15-sunxi #23 SMP Sun Jan 28 12:46:39 CET 2018 armv7l GNU/Linux

Hello all! I'm running armbian on a cubietrack wich I use for transmission and samba purposes. The Cubietrack is always on, and today I realized that was responding to ping but I couldn't log with ssh. When I restarted the system it hanged on this screen: The Cubietrack have ping response, but can't do anything. Any ideas? Thank you!

I have cubieboard2 nand chinese usb-modbus stik with ch340 chip. when I connet ch340 chip to usb cubieboard is freezed, ttyS0 is blocked. cubieboard is work but is very very slow, ssh is not disconnected but don't answer by my command. when I disconnect ch340 chip cubieboard will bee unfrozen but ttyS0 is blocked until I don't make hard (power) reset. Software reset is not unfroze ttyS0. I cannot found src for ch340 chip diver. Driver from china web is not compiling. uname -a Linux cubieboard2 4.14.18-sunxi #31 SMP Fri Feb 9 11:11:15 CET 2018 armv7l GNU/Linux dmesg [ 1129.203974] usb 4-1: new full-speed USB device number 4 …

I have tried to run the h3consumption monitor program (https://github.com/armbian/build/blob/master/packages/bsp/h3consumption) in an up to date Armbian 5.38 stable Debian Stretch 4.14.14 on a PiOne. After the command 'sudo h3consumption -h' and other commands it gives 'This tool requires legacy kernel on H3 devices. Exiting.' Is there any solution for this? Can I change the 3.4.*) to 3.4.*|4.14.*) in the script without any problems? https://github.com/armbian/build/blob/180112d72d31ec3629896f272a1d59ef3d83dc8d/packages/bsp/h3consumption#L123 # check platform and kernel case $(uname -r) in 3.4.*) HARDWARE=$(awk '/Hardw…

Hello, i have cubieboard2. This board boots and runs successfully with Armbian-5.xx-Cubieboard-Debian(Ubuntu)-xx-4.xx.xx image, but i have NO success to boot and run any Armbian_5.xx_Cubieboard2_Ubuntu_xenial_default_3.4.xxx_desktop.img image. Except, that i was able to boot and run Armbian_5.38_Cubieboard2_Ubuntu_xenial_default_3.4.113 image once and it worked for few hours, i was able to install some SW. After power up in the morning cb2 boots until kernel starts, show some flickering colorfull screen and in a second red power led is off and board is not showing any progress. HDMI display says no signal. Maybe someone has the same problem ? So to make it s…

I tried to build the armbian on my Orange Pi Zero Plus 2 to work on my astro project. I'm planning to connect the board to the camera module, which I'd assemble with a small scope (120mm focal length), and with a small TFT screen to make it a electronic finder scope. When I build and install the stretch server I've encounter several instability. There were some random crashes and finally I was able to get it stable. I'd like to share it here in case anyone is encountering the same. Here's the info: First I was experiencing random crashes and the exception message shows there's a problem at the high resolution timer. I simply disable the hr timer …

Hi Iam a newbie working on OrangePi and I have an orangepi pc plus board and I have installed Armbian_5.38_Orangepipcplus_Ubuntu_xenial_default_3.4.113_desktop on it. I have two user account created on the OS. Lets say user1 and user2. When i reboot the orangepi, it auto logins using user1, instead i want it to auto login using user2. Kindly help me. Thanks in advance, Girish

Hi, I installed pyA20 on my Orange pi PC2 and running one of the test files I'm getting segmentation fault. I am running ARMBIAN 5.34.171029 nightly Ubuntu 16.04.3 LTS. Can somebody help me troubleshoot the problem? Thanks,

Hello All, Trying to get sound working on my A20 micro. After switching to the Mainline kernel, the sun4i_codec loads and everything seems to be there. But alsamixer, aplay, etc all say that there's no such device. Running as root does not help so this is not a permissions issue. mute@micro:~$ uname -a Linux micro 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux mute@micro:~$ dmesg |grep sun4i-codec [ 10.491588] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok mute@micro:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevic…

Hi, I have been working on this problem for a few days. I have a orangepi plus2e and orange pi 5'' lcd. When I make all the connections and give power to the orangepi, I can not see anything on the LCD. At first only a white light comes out. Later on, I looked at the 5 inch screen produced by OrangePi with 640x480 resolution and the LCD settings on the H3 boards. I tried to set the resolution with the h3disp command, but I did not see the proper resolution. I did these on a different computer screen, and when I changed the resolution, nothing appeared on this screen.

The pcduino discussions appear to be centred here and the A10 appears to be a cutdown A20 so please forgive me if this is in the wrong area. I've been playing with an old pcduino2 and have got the latest mainline server version of Armbian installed on it. Very impressive. However, it appears to have only a single I2C bus and no SPI devices. It looks like there should be a sun4i-a10-spi-spidev.dts file somewhere or else some way to build the appropriate kernel modules but I have been unable to find this. I understand that this is a deprecated board but I should (hopefully) be able to perform any kernel builds required and am more than happy to feed the resul…

Hi , sorry for my english guys after Update /Upgrade to armbian 5.38 , my sytem did not rebooting anymore , before it was Fine for Long Time with Reboot Every Night I have not so mutch Experience with Linux i hope Same one can give me a hand, Best is a Step by step List I‘m connected directly to The Board via hdmi, i did not have a Network cable conected at Moment Because i‘m not at Home and i took The cubitruck with me to My workplace 2 pictures : https://picload.org/view/dagwdolr/fd49eb8f-23bb-4b4d-9763-e9bd87.jpg.html https://picload.org/view/dagwdola/6f5eea…

I have spent two days on LIRC. I am going to give up if no one can help me on this. My software conf are ARMBIAN 5.38 stable Ubuntu 16.04.3 LTS 4.14.18-sunxi and ARMBIAN 5.35 user-built Ubuntu 16.04.3 LTS 4.13.16-sunxi # cat /etc/lirc/hardware.conf # /etc/lirc/hardware.conf # #Chosen Remote Control REMOTE="None" REMOTE_MODULES="sunxi_cir" REMOTE_DRIVER="default" REMOTE_DEVICE="/dev/lirc0" REMOTE_SOCKET="" REMOTE_LIRCD_CONF="" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="None" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="audio_alsa" TRANSMITTER_DEVICE="hw@48000,r" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTE…

Hello all, i 've followed the steps from "sudo armbian-config" to create a hotspot. The hotspot is well created but doesn't start on next boot. I have to go back to armbian-config/manage hotspot to start it.. How can i do to get the hotspot autostart? With best regards Thanks Pierre Orangepi+2e with armbian 5.38 Ubuntu desktop

One of my orange pi zeros eth seems to be only negotiationg down to 10Mb/s full duplex. Not sure why. Below are examples of a stock nightly build. it only happens on one of the pis. [ 4.177634] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 4.181353] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 4.348951] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 4.349026] dwmac-sun8i 1c30000.ethernet: No regulator found [ 4.349104] dwmac-sun8i 1c30000.ethernet: Will use internal PHY [ 4.349331] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 58000) [ 4…

Hi all, I am using an Orange Pi PC PLUS2 with everything in the emmc for controlling another device through a serial connection (rs485) with a serial converter using FTDI chips. I am using docker containers to embed my application and easily deploy/share it. using uname -a gives me: Linux host-test 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux The problem is that randomly I get the following error: [135431.500807] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate [137213.011801] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate [138650.664850] ftdi_sio ttyUSB0: ftdi_set_ter…

Hello. I just wanted to let you know about a possible bug I have found in the kernel installation script. I was using my OPi+2e with the default kernel, and today I installed next to test it, using armbian-config. Everything went fine, and seemed very stable overall (I didn'd use it for more than two or three hours, though). But then I wanted to revert to default, so I used armbian-config again. When I rebooted, the board started the u-boot sequence, but it got stuck on "Starting kernel". No other messages after that. I tried several times, with the same results. Since I have no logs, the only info I can give you is that I have an external USB HDD …

Orange pi zero running Pihole. The web interface stopped updating and I found the /var/log file was 100%. Only way I could get it working again was to delete some of the files . How do I stop this filling up again please? From what i read it may be a armbian issue more than a pihole?

I had bought 3 Orange Pi Zero h2+ cpu (1x256mb ram and 2x 512mb ram) I'had tried Armbian Debian and Ubuntu based, but nothing changed or solved, i'had also tried DietPi(a debian base as armbian), but the kernel still the same: root@192.168.1.181's password: ___ ____ _ _____ / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARM…

I've gotten the board up and running and on Wifi, but this is supposed to be a dim wifi 'lamp'. Just to start out: how do I connect the +- to the board How do I tell the board to power on the leds And for more advanced: Is it possibly to do voltage-limiting dimming as opposed to PWM If no: what's the best way to do PWM? (I'm perfectly fine with creating a c program that simply turns it on and off at a specified hz, but there may be a more elegant tool I'm not aware of) Thanks

Hi. I'm working on it.I tried different systems ubuntu_lxde_desktop vs... Armbian 5.35 3.4.113 desktop board. gives a pink image error like in the photo. h3disp -m 1080p60 -d I've tried h3disp -m 1080p60 -c 1 I've tried h3disp -m 1080p60 -c 2 I've tried h3disp -m 1080p60 -c 3 I've tried but still no image how can i fix it ????

Hello, I installed the Ubuntu desktop image from: https://www.armbian.com/orange-pi-pc/ to the SD Card with: sudo dd bs=4M if=Armbian_5.38_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img of=/dev/sdb conv=fsync The orange pi does not boot, it took some time and the red LED is flashing on the top side and the screen is black. Maybe I did something wrong? Regards, caro

Hi to everyone, I'm using "Armbian_5.38_Orangepizeroplus_Debian_stretch_next_4.14.14" on a Orange Pi Zero Plus H5 I'd like to test this new board by working with processor overclocking. But it seems to me that it is leased at 816Mhz maximum. Can someone tell me how to take it to 1200Mhz or more? Thanks Antonio

I installed the kernels from and flashed them to sd card. Then i copied the modified .ko files from image that i built for latest non-rt kernel using the compile.sh. My orange pi zero is running rt version. When i try to modprobe the modified and copied module it gives me error: modprobe: ERROR: could not insert 'libcomposite': Exec format error I read that incorrect arch could cause this so i ran the file command. libcomposite.ko: ELF 32-bit LSB relocatable, ARM, EABI5 version 1 (SYSV), BuildID[sha1]=3a49e12c7809bbbdbdc3c5c5bd0fcd53e77dde44, not stripped i think module i built is not compatible with rt kernel i downloaded. I need to rebuild kernel…

Hello to all! I'm using Armbian on my BananaPi board. I've the following version: ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.15-sunxi BOARD=bananapi BOARD_NAME="Banana Pi" VERSION=5.35 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage I need to follow these instructions to wire a radio on the board: https://www.mysensors.org/build/orange But I cannot find the script.bin file. Why? I can remember the file was here on old releases. Any help or suggestion? Thanks, Simon

Hello everyone, Looks like i have some issue after last upgrade. I'm using a Banana Pi Pro as a file server at home (with samba mainly). The system is some kind of freezing after a few hours : i'm watching a movie and cannot go to the end of it. The system disappears from the network : no more access via samba/windows network, no more ssh, no more ping... Fortunately i am logging remotly so i can see that the system is still working somehow because it goes on sending syslogs. Last syslog is (the system "froze" at 20:10) : Feb 7 20:02:01 localhost CRON[3118]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Feb 7 20:05:…

Hi, Over the last couple of weeks, I have been trying to get Pi-hole working (and more importantly, stable) on the Orange Pi (along with the relevant Orange Pi zero H2+ ARMbian OS) without success. I realize that I am using "Tested" but as yet not marked "Stable" code, however I'm hoping this can help somebody here perhaps in terms of developing a stable OS for these little boards. I have rebuilt the SD card from scratch several time now. The SD card is of reputable make (Sandisk) and in fact I have tried two different cards, just in case this was a card issue. I'm using a reliable power supply, which I have verified by continuously monitoring it with my …

Hello! I am using armbian on orangepi zero. Currently SPI_CS line is LOW in default state and goes HIGH when selecting. Does it possible to invert it's state to be HIGH in default state and to be pulled down during line selection?

I have installed the latest stable Ubuntu desktop Legacy on BPI M1. The OS boot directly into the GUI. I am planning to use xrdp to remote desktop into OS from windows machine on same network. So I think it will be a good idea that BPI to boot directly into console to save some memory. If I need GUI then I can remotely connect from a windows machine. Is it a good approach? If yes, then how to configure to boot into console with minimum memory footprint.

In the 3.4 Kernel I could call: rmmod dhd modprobe dhd op_mode=2 To set the wifi module to Access Point mode. But with the latest Kernel 4.14(?) neither of these modules exist. Does anyone know what the equivalent of this code would be for 4.14, or some other way to enable AP mode?

OrangePI PC2 Problem report of the current state and improvement favor. --------------------------------------- Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop Keyboard and the monitor resolution.. other All kinds' setting, reboot, when, everything goes off. Therefore it isn't used. --------------------------------------- Armbian_5.34.171121_Orangepipc2_Ubuntu_xenial_next_4.13.14_desktop A keyboard is the monitor resolution only. It's preserved and it's practicable somehow. (1) Setting of other than above, reboot, when, please disappear. I close. (2) Cash of Root becomes full right now, even Mozc, install, can. ---…

Hello, First of all, I did check/tried anything i could find on similar issues, for similar SBCs Main issue: only 2/4 USB ports are powered, but they don't recognize any device (keyboard, mouse, memory stick), although, if i plug in an USB hub, it lights up. I also tried an Android and and an Ubuntu LXDE, same problem. What bothers me is that mouse and keyboard worked with the original Android that came pre-installed on the board. Config: - Orange Pi plus 2E (the one with 4 USB ports) + heat sink + HDMI to VGA converter Power source: I tried 4 so far, currently using a PSU of 5.15 V and 4 Amps, through the DC input, jack ba…

Hi, I just realized that my Orange Pi Zero running Armbian now shows a completely wrong temperature reading using cat /sys/class/thermal/thermal_zone0/temp This has not been the case until I updated to Armbian 5.38 by apt upgrade some days ago. Before that the reading was plausible. Not sure which exact version I was running before. I have a cpu temp monitoring script running and just realized that it now gets garbage. At the moment I get a reading of -12°C when outside temp is about 0°C (the OrangePi is in a water proof box outside on my roof). Not a serious problem, but seems to be a bug, so would be nice if it could be addressed :-) . …

Hi, we've been running 5.31 with VDPAU support for a long time now, and I've tried to "apt-get dist-upgrade" to newer version of Armbian. With 5.31 VDPAU works well, with 5.38 all calls to vdp_imp_device_create_x11() fail with "Error when calling vdp_device_create_x11: 25" Demonstratable on "vdpauinfo" Spoiler # Armbian 5.38 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 VDPAU capture: Enabled vdp_imp_device_create_x11(0x9c7f10, 0, -, -) -> 25 Error creating VDPAU device: 25 # Armbian 5.31 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 …

Hello on mainline stretch debian 9 Armbian 5.38 with cubietruck cubietruck is connected to eth0 and wlan0 My problem: when i disconnect eth0 i can not connect to wlan0 ( ssh and explorer page ), on my router i look wlan0: 192.168.1.119 and all is ok config: Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.15-sunxi System load: 0.36 0.59 0.64 Up time: 1 day Memory usage: 15 % of 2011MB IP: 192.168.1.161 192.168.1.119 CPU temp: 35°C Usage of /: 43% of 7.2G Battery: 100% charged result ifconfig: eth0: flags=4163<UP,BROADCAST,R…

Hi all, With a fresh install of version 5.38 (jessie 4.14.15, idle since 5 min.), I've a CPU throttling and load issues : Spoiler root@OPZ2:~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 07:29:43: 1200MHz 1.11 23% 13% 8% 0% 1% 0% 44.5°C 0/8 07:29:48: 1200MHz 1.18 1% 0% 0% 0% 0% 0% 43.1°C 0/8 07:29:53: 1200MHz 1.15 0% 0% 0% 0% 0% 0% 43.0°C 0/8 07:29:58: 1200MHz 1.14 0% 0% 0% 0% 0% 0% 41.7°C 0/8 07:30:04: 1200MHz 1.13 0% 0% 0% 0% 0% 0% 41.6°C 0/8 07:30…

Hi all, I've been using the A20-Lime2 together with Armbian for about two years now and I love the effort that the developers and the community have put into this amazing product. Until not too long ago I was on Debian 8 (jessie) on the legacy kernel for webcam compatibility reasons (after having tried switching to mainline from time to time). With the release of Debian 9 I finally had everything that I was looking for in the mainline kernel so I decided to upgrade to Debian 9 and then switch to the mainline kernel. I'm currently on ARMBIAN 5.38 stable with 4.14.15-sunxi and just had to force a reboot. The server I'm running is mainly a webserver, …

Hi , I have an orange pi zero . I installed armbian_5.38_Orangepizero_ubuntu_xenial_next_4.14.4 my orangepi zero. when ı use 'sudo nmtui' , it does not see wifi networks. I read many questions and answers about this issue but ı dont solve. I am waiting for your answers.

Hello, I'm running a Cubietruck with legacy kernel (3.4.113) since a long time. The use of the legacy kernel is mainly due to the fact that I'm booting from onboard NAND and this was not supported by the mainline kernel for a long time. Meanwhile Armbian's mainline kernel became Stretch in its server flavor and I'm thinking about migrating. However I'm suspicious this will still break NAND boot, despite the fact that the documentation claims plus "missing NAND support" is not listed under "known issues" for the Cubietruck. Can anyone confirm or deny that mainline kernel meanwhile does/does not support booting from NAND on Cubietruck? And if…

Hi all, I'm trying to understand how to make an infrared tx/rx module working. This is the module: https://www.aliexpress.com/item/5V-IR-Infrared-Remote-Decoder-Encoding-Transmitter-Receiver-Wireless-Module/32528109291.html Is there a way to make this works in userspace? Overlays? From the docs I was only able to understand how to enable existing overlays. I enabled cir, this is from my armbianEnv.txt: overlays=cir i2c0 but I don't know how to configure pins: which is rx which tx. Do I need to write down a new/custom overlay? I think that configuring pins is crucial to enable IR communication at some level but …

Hi.Can you help me fix this problem.Can't use usbwifi wl167g(need like reciever). Network-manager show(wifi enable) but firmware missing. Tried to install RT73_linux_STA_DRV1.0.3.6, have error, when step make, rtmp_main.c error "-march=i686". In new version desktop ubuntu wifi working, but shows slow video(I guess many improvements "use" a lot of resources).

Hello! It's about installing Armbian on OPi+ 2E without a reliable sdcard and with no proper card reader - U-Boot goes to sdcard, Armbian image goes to USB dong then installed to eMMC. I did this once but can't remember what device was the sdcard in Android, if anybody knows it would be great to share. It mounts as /dev/block/vold/179:1, but writing (dd) u-boot.bin to 179:0 or 179 doesn't result in a bootable sdcard (the OPi boots from eMMC, and as far as I remember if it has bootable sdcard inserted it should boot from it no matter what is on the eMMC). There was also an issue with the nand-sata-install - I had to remove some lines as it wouldn't allow writing …

Hi you all, I have flashed a good, tested and reliable 32GB SD card with the last build for Orange PI Win (armbian 5.38) and when first updating, it stucks in "waiting for headers" for too long. I have read that this is caused in Linux systems because one installs third party software whose repos take long to answer, but since here it is a first and fresh update, with nothing but armbian inside, I ask myself if it is normal or there is a problem with the servers at this moment. Only apt-get update ca take up to 1h 30 min, so it is really an annoying issue. Is anyone out there experiencing the same problem (and hopefully with a solution) ?? Thank you guys!…

Hello, I am trying to use g_serial but it does not work. I'm using fresh install of armbian (Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.7z), with apt-get update/apt-get upgrade/armbianconfig Install headers. Linux orangepilite 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux This is the overlay I use to enable OTG: sudo /usr/sbin/armbian-add-overlay usbotg.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&usb_otg>; __overlay__ { dr_mode = "otg"; status = "okay"; }; }; }; After rebooting OPi there are several erro…

Hello, I have "destroyed" my actual Kernel with TV Carddriver from here DVB Sky Website, ( the Media build ). Now the system dont found the TV Card and dont load the correct drivers. I wish to start the "old" Kernel (4.13.16) - delete the actual Kernel (4.14.15) with my problems - and install the Kernel 4.14.15 new ... Did you see what I will do - is it possible ? Can you help me please ? I found this - is it so easy ? apt-get install --reinstall linux-image-$(uname -r) Hardware: Cubietruck uname -a Linux wetterserver 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l armv7l armv7l GNU/Linux ll /usr…

Hi. When you install RPi monitor on a board using legacy 3.4 kernel (in my case, Orange Pi Plus2e), you can notice an error message in the "Memory" section of the web interface, as well as a very weird big number of used memory. That is caused because it tries to read some value from /proc/meminfo (named "MemAvailable") that wasn't implemented in that version of the kernel (I think it was implemented in 3.14, if I remember well). So I have made a custom version of the memory module, which gets the value for used and available memory using the same algorythm as HTOP, which has been many years around being very useful. I am attaching the file "memory_legacy…

Hi, I met another weird issue: I tried to setup a static IP address for my NanoPi NEO, which should actually bundle the NanoPI NEO's GigE MAC address and the static IP. Whenever I reboot the NanoPI NEO, its GigE MAC address changes, and an random IP address is automatically allocated, via DHCP. I mean, the previous MAC address did bundle to the static IP address that I allocated. However, there always exists a 2nd HOST name NanoPINEO which has a NEW MAC address and is allocated to a NEW IP address automatically. I'm not sure if this is an issue of the latest kernel I've just built? Or it is an issue of the FriendlyARM BSP for AllWinner H3 ? I posted …

ARMBIAN 5.38 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i Shows: Bus 004 Device 002: ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter But ifconfig -a show only eth0 adapter. No ra0 link I've tried sudo apt-add-repository ppa:thopiekar/mt7601 sudo apt-get update sudo apt-get install mt7601-sta-dkms But still no results.

Hello. I have an OPi +2e, with Ubuntu 16.04 and legacy kernel 3.4.113-sun8i. I tried to install Nextcloud via a Snap package, but got this error: error: cannot perform the following tasks: - Run configure hook of "nextcloud" snap if present (run hook "configure": cannot open mount namespace of the init process (O_PATH): No such file or directory) I googled for the message, and found out that there are some bits needed in the kernel, for Snap to work (see https://forum.snapcraft.io/t/nextcloud-snap-install/2674/3 ). Has anybody got this to work? Maybe with mainline kernel?

I am using an OPi+ 2e as an OMV box. Tonight I updated to 5.38 (4.14.15 kernel). After the update, the network connection drops between the router and the OPi at random intervals. At least once in a hour, sometimes within 10 minutes. Tried restarting the device and the router, to no avail.

I've followed the instructions below and cannot get past the "couldn't find avaliable UDC" error. help? https://vjordan.info/log/fpga/nanopi-neo-usb-otg-with-armbian-mainline-4x-kernel.html

Hello. When the browser starts (chromium), the board hangs, the screen turns gray. when in LibreOffice Writer I build graphics or draw figures or lines, the board hangs, the screen turns gray. load on the processor and memory for 100% console applications - all in order. What is the problem?

Hello. How I can to set the 480x800 resolution? I have LCD display with portrait orientation and no one display mode from h3disp does not fit. On boot display is working fine, but after booting everything is bad. Booting video: After booting:

Hi I installed armbian on orange pi plus win and I sow the resolution isn't good. so I tried h3disp command but I got this What is the resolution software in this model? I tried to install h3disp but it isn't in repository!

Hi there, I noticed there are up to date builds for Pine64 for Debian and also up to date ones for Ubuntu for the Orange Pi Win. But none for Debian and Orange Pi Win, newest ones are from November probably with legacy kernel? Is this just some kind of build script hiccup? If not, do you have an idea about a timeframe for new Debian builds? (I'd rather not use Ubuntu if it's just a few days/weeks I'd have to wait for Debian.)

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Aud…

Hello! I have problems with Banana Pi and for today - updated all packages, and I can't connect via SSH nor FTP to my Pi. I have not changed anything, but there is automatic script which dist-upgrades the whole system, it is running once a day. Till 12.34pm CET everything was working fine - from logs, even I think till past 4pm I have connected via SSH to Pi, but then after kernel upgrade (seen note after logon) and reboot I can't access Pi in any way. I've tried to see logs: connect SD card to laptop with Linux to check if there is any problem, but didn't found nothing special. I've also tried to attach HDMI monitor but no signal. Seem…

Hello everyone. I would like to create an update system, which via a link on a web page, will check on an ftp server and if a version is newer, download the img file and install it. it is the installation part that poses me big problems. to write an img on the sd we must use the command dd if = ..... of = ...... But since the sd is used it does not work. I had thought of going through berryboot but a priori it is not functional on the m2. If someone has an idea thank you

root@orangepizero:/boot# iptables -nL modprobe: ERROR: ../libkmod/libkmod.c:586 kmod_search_moddep() could not open moddep file '/lib/modules/4.14.14-sunxi/modules.dep.bin' modprobe: FATAL: Module ip_tables not found in directory /lib/modules/4.14.14-sunxi iptables v1.6.0: can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. root@orangepizero:/boot# uname -a Linux orangepizero 4.14.14-sunxi #1 SMP Thu Jan 25 12:20:57 CET 2018 armv7l armv7l armv7l GNU/Linux root@orangepizero:/boot# Can someone help me how to fix this issue on Orange Pi Zero - 512 MB board ? I am running Armb…

My problem with Cubieboard3: input audio file hallo.mp3 with content "Hallo Otto" play hallo.mp3 --> Output on analog audio clipped to: plop lo otto plop It looks like the audio channel must be switched on and off for use. What can I do?

I have to clear possible blocked interfaces everytime I log on to get access to Internet. I m connected to network but if i dont clear that button i dont get access. Can help me .

Hi, Firstly my thanks to the team for an outstanding job on ARMbian. I'm relatively new to this particular flavour, using it on my Orange Pi H2+ board with a few different builds under my belt now. Recently I have been having some troubles getting Pi-hole to work on the little Orange Pi board. Twice I have had it up and running perfectly, with full DNS and DHCP control of my home network, accommodating about 10 devices. However after about 6 - 12 hours of operation, they ceased to function. First time around I was not home to witness it, but when I returned later, the Allwinner chip was running pretty warm (around 60 degrees C core temp) and non-responsive, even to s…

I've installed armbian 5.38 debian stretch 4.14.14 on my Orange Pi PC .. after changing notwork settings (by using "armbian-config") from DHCP to Static , then back to DHCP, eth0 is not able anymore to get IP address.. "newtorkclt" return: IDX LINK TYPE OPERATIONAL SETUP 1 lo loopback n/a unmanaged 2 eth0 ether n/a unmanaged every suggestion will be usefull..

Hello again. I am beating my head against the network configuration again and would dearly love some help. I have two orange pi pc boards with static ip's in the 192.168.1. range. They are only connected to each other. They can ping and ssh each other just fine. I am trying to set up nfs shares between them without success. In /etc/exports I have: /home/martin/folder 192.168.1.*(rw,sync,no_subtree_check,nohide) I have "ALL: 192.168.1." in my /etc/hosts.allow. In /etc/fstab I have: 192.168.1.XXX:/home/martin/folder/from_lev /home/lev/folder/to_martin nfs rw,sync,noauto,user,x-systemd.automount 0 0 And vis-versa on the other pi. The fold…

Hello everyone, This post shows one of our users ported the Mender open source (over-the-air) OTA updater to the Orange Pi PC Plus: https://mender.io/blog/guest-post-on-porting-mender-to-the-orange-pi

I should have known better..... today i did an apt update and saw thet there was an update to 5.38. Installed it and like with nearly every last update the device (OrangePi +) didn't boot. Did you even test updates in the stable repo before ? Don't know whats going wrong, so i will test it, but thats annoying.....

Hi, I use OPI0+. Bluetooth works well when using WiFi as a client. In access point I got an error like"Invalid command" "ConnectionAttemptFailed". Is there any way to fix it?

I think 16 seconds is the max. value of the watchdog timeout of H2/H3, However, I cannot set it to 16 seconds. When watchdog-timeout = 16 in /etc/watchdog.conf, the timeout is 11 seconds : /etc/watchdog.conf max-load-1 = 24 watchdog-device = /dev/watchdog realtime = yes priority = 1 watchdog-timeout = 16 interval = 3 root@orangepizero:~# systemctl status watchdog.service ● watchdog.service - watchdog daemon Loaded: loaded (/lib/systemd/system/watchdog.service; enabled; vendor preset: enabled) Active: active (running) since Mon 2018-01-29 11:10:27 HKT; 3min 31s ago Process: 851 ExecStart=/bin/sh -c [ $run_watchdog != 1 ] || exec /usr/sbin/wa…

Hello, I tried to install the four versions available for orange pi plus 2e, and none of them works. I can't even log in via SSH. I know they are nightly versions, the version with legacy kernerl works great... I just write this, because I have a spare orange pi plus 2e, and i'd like to offer to try any new version.

Hi everyone. When I tried plug in my banana pi to tv (rca video(AV),). I can see only boot(where label armbian). maybe need special resolution, i tried 800x600, 640x480, nothing.

Hi to you all. I've had a functional boot from USB flash drive on my OrangePi Zero and when I've updated kernel yesterday from main repository and reboot_ed boot stoped working. I've tried on another fully functional OrangePi Zero with same rom on it and still not working. I've tried to put new "virgin" image to USB flash drive and still nothing. Tried to erase spi and write it againe and still nothing. Any idea what could happened. I'll try today to get serial console to see what is going on during the boot proces.

I have a NanoPi Neo Air (Allwinner H3 SoC) with onboard wifi and a serial interface. Unfortunately during some late hour hacking I managed to accidentally connect 5V onto its TX pin, I think effectively screwing up its UART0. I can no longer connect to it via a USB to TTL Serial cable. Looking at the NeoPi Nano Air's pinout diagram, it seems to have more UART devices (UART1 and UART2 even) so I wonder whether there's a way to set up armbian to communicate via these during boot? Another idea I had was to try to bypass the UART completely and to hook up the board via the wifi. Now, without having any access to a serial console, I need to …