Allwinner sunxi

I got 2 x Orange PI pc+ running Armbian (install by same SD card on eMMC). My two orange pi pc+ got same wlan0 mac address. I did research on forum and saw some suggestion about bug of Network-Manager. I try remove (purge) Network-Manager but see no difference. I also try look in u-boot but don't know how to set mac address on the u-boot part. How should I make my 2 pc+ board have difference mac address? want to run these two board under the same wifi network. Please suggest. Thank you very much in advance.

I apologize for asking such a basic question. I have recompiled the wifi module on an Orange Pi PC+ to operate in concurrent mode so it can act in both station and AP mode at the same time, allowing it to be a wifi repeater. The problem is, this feature is lost on every kernel upgrade, requiring me to recompile the module each time I upgrade the kernel. The kernel module driver often changes slightly between kernel versions, and I have to track down and fix new bugs in the source code that prevent it from compiling when concurrent mode is enabled. I'm happy with how the wifi module performs now, but don't want to lose the ability to get needed kernel updat…

I have an H618 Android TV Box with 8GB of RAM and 256GB of storage. Any build option results in an error. I would be immensely grateful for any help. Thank you. armbianarm_errors.txt

Hi all. Strange thing happens. I've tried to run a fresh installation of the 4.4.3 kernel version of armbian 5.04. The first boot takes forever (I gave up after 2 hours; a few times). It started and hung up at updating packages. Every try; tried about 10 times. If I switched to 5.04 with kernel 3.4.110 - the first boot takes about 1minute and cubietruck rebooted once, so everything worked perfectly. Any idea what could happened? Some extra info: If I logged in during this "updating packages" period, the normal process of creating a new user worked as normal. After that I could restart the cubietruck normally. So my question: Do I get some problems if I …

Hi everyone, I'm trying to connect Tiny LCD to OrangePiOne. I bought this cheap LCD display with touch panel. http://www.aliexpress.com/snapshot/7757492669.html?orderId=75894630877559 --My environment-------------------------------------------------------------------------------------------------- Orange Pi One Armbian Jessie Desktop with legacy kernel DS1302 RTC module(work with WiringOP) 720p DVI Display 2.8" SPI Serial Port 240x320 ILI9341 TFT LCD Display Screen Touch Panel Backlight Module ------------------------------------------------------------------------------------------------------------------------ I connected and tried to configure the L…

Hi, how are you? I'm trying configurate my OPI zero to manage users of my network using Dalo Radius (Tutorial of this forum), but I need configurate to work with ETH1 (a Gigabit USB adapter) and no have find the configuration for change this... And if I connect the adapter, I'm loss the connection with OPI... I'm using a TP-Link Archer C60 to distribute my network via Wi-Fi, but using a PSK. I want to remove the password and use via radius to add and remove users of my network, with the vantage of captive portal. Via ETH1 I don't have any idea to where start, via Wi-Fi of Orange PI I'm no try because is not usual for me... *Sorry for my bad english..…

orange pi PC has only three USB ports . so i look for ways to save USB ports . one way is to use wireless keyboard & mouse , but this also occupy one USB port . so i use vnc . at orange pi aptitude install x11vnc and /etc/rc.local -------------------------- x11vnc & exit 0 then at debiandog linux　 xtightvncviewer 192.168.100.xxx (orange pi's address) then apear . and more i attach usb camera , and click cheese , the next sｃｒｅｎ appears.(camera aims at TV). this is a monitoring camera . i thik the conbination of drone and orange pi PC has big ability . but debian dog has no sound . how to get now so…

Unfortunately I don't have a USB keyboard or USB UART cable around... is it possible to compile an image that has my wifi information baked in?

Hi guys, today a archive to run an orange pi one with a 5v dedicated power ac (not usb one used for smartphones). i try either official. Ubuntu ldxe image and armbian (burned with etcher on Samsung sd) On my first try I saw on my 720p TV (hdmi) some write then nothing else, no signal. And a green led lights up with a red led blinking. on next tries no video signal at all and only the red led is still light on. I can't try android img cause phoenixcard app give me error. Is there something I could try? Thank you or just you can tell me what that leds means

I'm trying to set up my OPI PC+ with a static IP address on wlan, but it doesn't seen to be working. This is my /etc/network/interfaces file: allow-hotplug wlan0 iface wlan0 inet static address 192.168.25.160 netmask 255.255.255.0 gateway 192.168.25.1 dns-nameservers 8.8.8.8 8.8.4.4 wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf I tried both with wpa supplicant line commented and non commented, but every time I boot up the board, it is still with the DHCP address.

Screen capture mpv and mplayer with vpdau outputs it is not possible, on players places window area is black. I tied with fbgrab and shutter. What screen capturing program we have to use for vpdau outputs capture?

Hello I was build image for my orange pi pc2 devices: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.46 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=custom BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image I was faced with strange thing: After burning another image and lunch it on the device - on the first (and every) boot I see "first start panel window". And when I do formatting this SD card, and burning again - everything alright (first start panel window dose not appear) I have been already burn 10 SD cards with same image and met th…

Good morning, I have a NanoPi Neo core where I am trying to use the usb ports (USB1, USB2 and USB3), the first thing to say is that all usbhost is active in armbian-config. The system does not recognize me anything in any of the 3, not a pendrive, or Wi-Fi or anything. If I go to armbian-config, I see that the DTB system that has loaded is that of the NanoPi air, I do not know if it can influence. USB devices receive power when connected. Any idea if I have to activate something else or modify the DTB or something? I have tried adding to armbianEnv.txt this line at the end fdtfile = sun8i-h3-nanopi-neo.dtb but nothing. Thanks and best r…

Hi specialists, I'm trying to understand how the axp209 on Banana Pi works with the A20. In the Banana Pi schematics I see, that they are connected with only four lines. Two lines are used for I²C (TWSI), one is from axp209 PWROK to RESET# of A20 and another one is connected from axp209 IRQ and GPIO2 to NMI# of A20. When system is off and I press my Power Button (K1) on the Pi, the system is booting. System is running and I long press the Power Button, System shuts down. But can anyone say whats happening? What does axp209 do with IRQ, GPIO2 and PWROK pins? Wich way does the A20 recognize, that it has to shutdown? Yours Martin

My newly received Orange PI Plus 2 gets stuck in a reboot loop, if I try to boot headless (no USB, no HDMI; UART is connected to see boot messages). Is such a problem known here? I have the same issue with some other linux images from other distributions, but hope to find some experience here. In detail: Power supply: Regulated Power Supply set to approx 5.2V (max 2A, built-in analog amperemeter shows max 1.4A during boot). No cables connected except power supply and UART I tried various SD-Cards (8GB or 64GB SDHC) --> The Orange PI Plus 2 boots till USB initialization and then reboots (sometimes it freezes). …

I had a rather crazy idea (in my opinion) of trying to hook up a bluray drive to an Orange Pi Zero Plus that i have a spare of, then possibly set that up as an iscsi target with LiO to create a network attached BD drive. However, I'm already stuck even getting the BD drive to work with the OPi in the first place. I have the optical drive hooked to an externally powered USB 2.0 to ATA bridge (has a SATA port on it as well, this hardware config was tested in windows and worked great) and that's plugged into the single USB port on the board. The problem i seem to be having (not entirely sure I'm correct, very new at this) is that sr_mod is not enabled or present. T…

Hi, I am building a voice assistant on OrangePiPc on latest Armbian 23.11.1 Bookworm \l root@orangepipc:/etc/alsa# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sun9ihdmi [sun9i-hdmi], device 0: SUN9I-HDMI PCM i2s-hifi-0 [SUN9I-HDMI PCM i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 For some reason when I plan an audio file using cvlc or play cli tools, about 1 first second of audio is skiped for some reason. I guess this time DAC is initialized. How I can solve this issue?

I am failing creating a bootable SDcard. I download latest image and flash it using etcher. Everything goes smoothly. But when the SD is inserted in the device and the device is powered on, nothing happens (no video output, no LEDs blinking, no network LEDs blinking). I am facing this issue with bananapi M1 (and pine64, but I need to get bananapi working only). This is not SDcard issue, since other distros are running smoothly. This is not PSU issue, since other distros are running smoothly. I was testing Debian Jessie Next 4.9 and 4.11.

Hello, i like to work with 1wire 18b20 sensors on my Oragne Pi one , with the latest Armbian Bionic . root@orangepione:~# uname -r 4.14.65-sunxi In this forum and in the orange pi forum, there are some instructions, but I think they are out of date. 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot Edited by nopnop2002 at 2017-8-5 17:10 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot 3.driver load sudo modprobe w1-gpio su…

Dear community, I am experimenting with MangoPi board, trying to communicate with the CC2530 Zigbee board . To do so, I need an available UART port, the UART0 (/dev/ttyS0, pins 8 and 10) seems to be occupied by the console, but there should be two other UARTs according to the schematic. Some info: pi@nezha:~$ uname -a Linux nezha 5.19.0-rc1-d1 #trunk Fri Jul 22 12:44:22 MSK 2022 riscv64 riscv64 riscv64 GNU/Linux pi@nezha:~$ setserial -g /dev/ttyS* /dev/ttyS0: Permission denied /dev/ttyS2, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS3, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS4, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS5, UART: …

After upgrading my Cubietruck with the latest armbian image (Vanilla Debian Jessie) I noticed that command line access is restricted to two parallel consoles (via ALT+F1, ALT+F2, -) only. Is there a way to overcome this limitation? Any remedial hint would be greatly appreciated. Thanx in advance. By the way, SSH terminal access seems to be possible almost inititely in number.

Hello,I have a bananapi m2+ I would like to install kodi version 17 to the standard repositories is the only version of 15 which doesn't suit me. tell me how to install the 17 version? I'm new to Linux and don't understand much,if there is a possibility lay out the user manual which would have helped with the installation. I want to install on server version armbian and that would be after the launch of the banana pi automatically instead of a desktop was loaded kodi interface, so it is possible to do?

Hello, I tried to install the four versions available for orange pi plus 2e, and none of them works. I can't even log in via SSH. I know they are nightly versions, the version with legacy kernerl works great... I just write this, because I have a spare orange pi plus 2e, and i'd like to offer to try any new version.

Hi, I'm using Armbian Linux on a Cubietruck A20 device configured as a media, file and backup server. Unfortunately while trying to fix a persistent SATA-cable connection problem I accidentally pushed the FEL button on the device. Now the device is always booting in FEL mode searching for USB devices, and I'm unable to reverse this. I have been looking at multiple pages about the FEL mode but I'm unable to find useful information on how to quit or exit this FEL mode and to have the cubietruck booting as it did before. Although I'm not a Linux novice, the information about FEL is quite complex and I have to admit I'm clueless about how to fix this s…

I have installed the 'watchdog' package (apt-get install watchdog' on an Orange Pi Plus 2E, and it does not seem to be working as I would expect. If I write output to /dev/watchdog the system will reboot, but if I stop the watchdog service (and wd_keepalive) the system does not reboot. I did un-comment the path to /dev/watchdog in the settings file, but have generally not changed anything else. Is there some other required setup needed to allow this to function?

Hello, I'm using the last Kernel (4.13.3) and U-boot (2017-09). I noticed that the device does not reboot each time we ask for it. It sometime get stuck and I have to start it manually, this is really annoying for my needs. I figure it out that the Device Tree from 4.13.3 introduce some improvement on AXP209 and power management. I tried Device Tree file from 4.11.x and everything seems fine. Does any body noticed it ? Thanks

Hello, First I want to thank you for wonderful linux distribution it was been awhile since I last used it, and lot of things changed for me. So I need someone to point me in right direction to catch up with some changes. i'm using Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14 First thing I do not see is script.bin - I use to configure gpios, which one gonna be uart, spi ........ etc. How can I do that now. Second thing is h3consumption tool, I usually use it do disable some system components, like usb in order to lower cpu temperature. I found answers to other things so far using google. So if someone point…

Hello All, I am on NanoPiAir, I really want to use my home made ir receiver with this board haha So I try : insmod /lib/modules/3.4.113-sun8i/kernel/drivers/media/rc/gpio-ir-recv.ko and I have : insmod: ERROR: could not insert module gpio-ir-recv.ko: Unknown symbol in module In another side I tried to build a lircgpio.ko with a patch but I can't find the .ko generated despite kernel compilation succeed. If someone can help, this should be great

how can I force set HDMI output like 1024x768 60hz or something like that? hello I have OPI lite 2, I use Armbian_5.61.180927_Orangepilite2_Ubuntu_bionic_dev_4.18.10.img, when I boot OPI I can see preboot information then after 1-3 sec I have no signal on my monitor I tried different hdmi cables without luck uname -a Linux orangepilite2 4.18.11-sunxi64 #312 SMP Sun Sep 30 00:22:52 CEST 2018 aarch ps: monitor dell 2414h I tried different OS like android (native, zidoo h6 pro, beelink gs1) also ubuntu 16.04 without any monitor issue, at least video output worked at any cases but they have another issues

Well, I have this old M1 lying around. I found use for it. However HDMI output seems to be broken and I have composite video USB dongle at my hand and it boots... but I can not do anything with it. The question becomes: How on earth can I make it "ssh login"-able from the first boot (preferably with mdns)? What should I do with the image? Auto configuration tools - as handy and nice those are - are not for this. Thanks.

Greetings, Some time ago, I built armbian with kernel 5.4.51. I applied a patch to two dts files that allowed for the OV5640 camera to work. By "work", I mean /dev/video0 was present in the system and /dev/media0 was also present. I could set camera parameters with media-ctl pointing to /dev/media0. Now, I've updated, and using a legacy kernel, 5.4.65, I cannot reproduce this. I've applied the same dts changes, but upon booting this image /dev/media0 is missing. I've compared the two kernel configurations, and there are very minimal differences: # diff config-5.4.51-sunxi /boot/config-5.4.65-sunxi 3c3 < # Linux/arm 5.4…

Hi, I am having a hard time getting Armbian to boot on my Cubietruck. I have recorded some serial output but it does not show anything helpfull (at least for me). It just stopps at "Starting kernel". Verbosity is set to 7. Serial output 21.02.3 https://pastebin.com/DMWRzTgn Serial output 21.02.1 https://pastebin.com/a9Hasywc I tried the same SD-card and power supply with Arch for ARM. Arch boots fine. Serial output Arch Linux: https://pastebin.com/bMPf3gfx What further options do I have to debug this? As I am not really familiar with Arch I'd rather run a Debian / Ubuntu based OS. Best regards, Albert

From the CLI that is. I plan on using the OPi as a headless MIDI processor, and I'd like to be able to switch remotely the audio output of ALSA between the default audio-out, the HDMI out and a USB sound card (CM108-based, tested working with the current kernel). ALSA documentation isn't well maintained, most of it is old and doesn't correspond with the current state of the software (config files locations and names, contents etc). I tried various examples I found on several bulletin boards, but none really worked since Armbian seems to do things a bit differently. So I'm asking here: on Armbian, how do I switch remotely the output audio device in ALSA? No remote …

Hi, for all my automation projects I use BananaPi and BananaPro. As far as I know the difference is the script.bin file. Is this right? I will not maintain two Images. Right now I use the Image for the BananaPro 5.14. I changed the sym-link to BananaPi.bin. But the hardware-info after login shows "BananaPi Pro". Is there anything more I have to do? Thanks. Steffen

Hello, I want to read data from UART3 on OrangePi One. I want to use UART3 (pin 8 & 10), so I enabled uart3 overlay at /boot/armbianEnv.txt. Now I expect to read data via minicom -b 115200 -D /dev/ttyS3 but I read nothing unfortunately. What am I missing? Any help is appreciated. I'm using Linux orangepione 4.19.38-sunxi (sorry, armbianmonitor doesn't generate link) Thank you, Regards

I have an OPi PC+ running Armbian. Bought an RTC called "DS3231 for Pi" and connected the 3.3V, ground, SDA and SCL pins to the GPIO connector. Ran "sudo i2cdetect -y 0" and it prints a table with "UU" in position 0x68. Ran "hwclock -w -f /dev/rtc1" and the response was "bash: hwclock: command not found" I looked in a subdirectory of /etc/ and found fake_hwclock and hwclock.sh Can anyone tell me what is wrong? Perhaps I should have modified something else before running hwclock? Thanks...

Hello armbianers ! Armbian 22.11.1 Bullseye with Linux 5.15.80-sunxi on a banana pi m1 I've connected a lipo battery to my bpi m1, and now when I try to shutdown -h 0, it ends up in a kernel panic and instead of shutting down it remains powered up. Is there anything I can do to fix that? I'd know how to shut it down talking to the axp209 via i2c, but I'm not sure how/where to put that, or if that would be or not the proper way to go. Thanks, George.

Hi! I just installed Armbian Jessie on my Cubietruck to replace the outdated CubianX-distro. Title: Armbian 4.81 Cubietruck Debian jessie dev (unofficial) Kernel: Linux 2016.01-rc3 Build date: 28.12.2015 I use the Cubietruck as an owncloud-server and as a tvheadend-server. Tvheadend doesn't work properly. There seems to be a hardware-issue with the DVB-S2-receivers. One of them fails sometimes. Tvheadend often stopped. But now i found one (the?) reason in the syslog: lowmemorykiller Feb 4 08:29:04 localhost kernel: [11909.498000] lowmemorykiller: Killing 'tvheadend' (622), adj 0, Feb 4 08:29:04 localhost ke…

I am having a problem setting up the wireless on OrangePi PC Plus. Kernel module 8189fs is loaded, but no wlan0 interface appears. Here is my lsmod output: root@orangepipcplus:~# lsmod Module Size Used by rfcomm 32863 4 bnep 9617 2 bluetooth 174065 8 bnep,rfcomm mali_drm 2732 1 drm 178255 2 mali_drm sunxi_cir 1601 0 pcf8591 3363 0 bmp085 3487 0 mali 123208 0 ump 29379 3 mali 8189fs 1050451 0 hid_logitech_dj 10040 0 ifconfig and iwconfig do not show an…

How can I disable or lock my opi + 2e's microphone with a password to prevent anyone from hearing thnks

Hey all Testing with an Orange Pi Zero with mainline kernel. I've just noticed that none of the usb devices show up which are connected to the pin-header usb ports Is there any quick fix for this? e.g. enabling something somewhere? i think i remember maybe enabling something before to use these ports but i can't quite remember now. checking armbian-config thank you elliot

I have just received an Orange Pi PC Plus, and am mostly happy with it. Linux orangepipcplus 4.14.18-sunxi is installed on a microSD card. There is a minor problem with IP addresses. When I first turned it on I forgot to plug in the network cable, so naturally ifconfig showed no IP address. I plugged in the cable, waited a minute, and tried again. Still no address. Maybe it's not hot-pluggable. Reboot, and I got an address. Since it was outside the range my server accepts I assigned a static address in the router, and rebooted the router. ifconfig still showed the first address, even though the router's client list showed the new …

I would like to make Orangepi zero to capture USB output destined for a printer in order to log the output from a system. 1 ) Mimic the connected USB printer (so that the machine thinks it still has the original printer attached) 2 ) Capture the output from the machine 3 ) Send the captured output to the printer.

To replace my dead home server (which was just a dead laptop anyway), I picked up an Orange Pi PC for cheap locally. After solving power supply issues, I tested GUI and media performance on the board, with an aim to perhaps use the composite out for emulation, before concluding that this wasn't the best choice for the board. (That, and it'd kill my performance for the more useful server aspects.) While technically impressive, it wasn't really worth it when my PC is right there for me to use to play those video files I would on the board. Looking into the matter, it seems the ideal solution for a file server would be to install the Mainline kernel to benefit fr…

Hi Everyone. I expect I'm making a simple mistake here, but I'm pretty new to this and could use some help. I am trying to set a static ip address on an orange pi pc running armbian Jessie 5.36. I want a static ip to set up an nfs between multiple boards. I've done this before on debian desktops, but this time I'm getting errors. I have tried multiple ways (editing the /etc/network/interfaces, nmtui, nmcli) without success. For simplicity, here's a version of what I'm doing. I start with a clean install. The Opi connects to my router fine. I add and update all the packages I need, then use nmtui to change the name of the network connection from "Ethern…

Hello, Long time follower, first issue/bug post. I have read and tried several options over period of time to get this working, nothing helped. ReWrote Clean image, changed SD cards (and sizes 8 > 16 > 32 > 16g). Setting /etc/netwrok/interface allow-hotplug eth0. iface eth0 inet dhcp NetworkManager.conf [ifupdown] managed=true/false Tested for power consumption using ( have a 5v 4A supply ) and I know I have sufficient power stress -c 4 -t 10 stress: info: [1347] dispatching hogs: 4 cpu, 0 io, 0 vm, 0 hdd stress: info: [1347] successful run completed in 10s stress -c 2 -m 2 stress: info: [1359] dispatching hog…

I have my Orange Pi running for a while on the CLI release of Jammy with kernel version: 6.6.16. It has been working well. I was building another one up and I went to download Armbian and I noticed that OrangePiZero is community supported now (Don't think it was before?). The current version to download says that network issues are expected. I never had this on 6.6.16 so wanted to stay on that. I looked here: https://armbian.hosthatch.com/archive/orangepizero/archive/ But there is only minimal for 6.6.16, all/most others have minimal and CLI (typical, the one I want lol) Is there somewhere else I could find the CLI vers…

Hello, I try to build a headless music server, that can - boot from nand then from ssd - audio needs to work, SPDIF and analog - runs mopify - Power on / off via script All Images I tried so far - Ubuntu Trusty, Ubuntu Trusty upgraded to Vivid, Debian Jessie - do somehow not support the Power button. Same to Lubuntu 2.0 stock and Stefanius images. I did install acpid and acpi-support-base I configured systemd as described here http://www.forum-cubieboard.de/Thread-cubietruck-pwr-on-powerknopf?page=3 just does not work. If possible I'd like a latest system - Jessie or Vivid, but thats secondary. Cubietruck_Debian_4.0_wheezy_3.4.108 - apt-get update &am…

Hi, My Armbian Vanilla for Cubieboard1 is working las 2 months... Theres is an iissue with I2c, that I don't know how to avoid or stop Dmesg and syslog are flooded with this message Feb 7 11:09:05 localhost kernel: [172015.158063] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:06 localhost kernel: [172015.688415] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:06 localhost kernel: [172016.158440] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:18 localhost kernel: [172027.837841] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:18 localhost kernel: [172028.087760] i2c i2c-0: master_xfer[0] W, addr=0x34, len…

Hello, Has anybody successfully used the IR sensor on Banana Pi M2? From this, after I load the sunxi-cir module, I should see the sensor in /sys/class/rc/ but I see nothing. Nothing on dmesg either. Anyone who could point me in the right direction?

the entry in /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq (maybe the path is wrong, I haven't the machine and I'm going by memory) is readable only by root so it is not usable to a normal user to display the current frequency of the processor, There is a way to change this behaviour? My distribution is for Olimex-A20-Micro with legacy kernel 5.14 if i don't go wrong. TIA and regards

Hi everyone. I have a opz with H2+ and expansión board. I had installed Jessie before. And now, I upgraded to stretch. why espeak-ng sounds so bad?? in jessie that did not happen.

Look at the description https://docs.armbian.com/User-Guide_Armbian_overlays/ when I set UART I2C in armbianEnv.txt it should be overlay_prefix=sun50i-h616 overlays=i2c3-ph uart5-ph as described on the given page But when I use armbian-config and go to Manage Overlays my settings are not seen and I have to set them but the names of all overlays are preceded by the prefix. After selecting and saving the settings in armbinEnv.txt it is overlay_prefix=sun50i-h616 overlays=sun50i-h616-i2c3-ph sun50i-h616-uart5-ph as a result the defined overlays are not loaded Is it supposed to be like t…

Hello there, hope you been able to give me a hand; I've downloaded and installed without problems the current Xenial server Vanilla distro on my Banana pi. Then I've tried installing iptables, but for some reason, everytime I execute 'sudo systemctl start iptables' I receive the following error message: Failed to start iptables.service: Unit iptables.service not found. I know that something has got installed, as iptables -L provides the expected output; however, any systemctl command for iptables (start, stop, enable, restart) fails with the message above. Certinaly, searching for 'iptables.service' at file system returns no matchs, so file is really missing. My under…

Is there any real-time patch support for the Banana Pi M2+? Thank You

Hey folks, I'm trying to play back a couple test files, H.264, 720p. These play without dropping frames on the stock Android ROM for a little while but then freeze, seemingly on certain keyframes? It's always in the same place. Anyway, I tried playing them with mpv on Armbian 5.38 desktop install and it drops frames like crazy. I know the stock Android ROM can play back Youtube content (in the app) without dropping frames - it seems like this should be doable based on what I understand about the capabilities of the A20 and on hardware support in the legacy kernel in the Armbian image ... is there tuning I should be doing? Or options for mpv that I can try? I've used VLC f…

Hello. I have several new NanoPi-NEO Core devices. OS FriendlyELEC (Ubuntu 16.04.2) was already installed on them, and it does not allow me to boot from the SD card. There is an image created by a script emmc-backup.sh How do I deploy this image?

Hi Harness the Board Orange Pi + 2. I propose to add the configuration for it. sasha@ubuntu:~/orange/sdk/lib$ git diff master..add-orangepiplus2 diff --git a/config/boards/orangepiplus2.conf b/config/boards/orangepiplus2.conf new file mode 100644 index 0000000..5d37e8c --- /dev/null +++ b/config/boards/orangepiplus2.conf @@ -0,0 +1,11 @@ +# H3 quad core 2GB RAM WiFi eMMC +BOARD_NAME="Orange Pi+ 2" +LINUXFAMILY=sun8i +BOOTCONFIG=orangepi_plus_defconfig +MODULES="8189es #gpio_sunxi #w1-sunxi #w1-gpio #w1-therm #gc2035 #vfe_v4l2 #sunxi-cir" +MODULES_NEXT="8189es" +CPUMIN=480000 +CPUMAX=1296000 +CLI_TARGET="jessie:default" +DESKTOP_TARGET="jessie:default" +KERNEL_TARGE…

Hello, I've got some problems with a Cubietruck. First thing to state is that the com-port apparently has died. It was connected via a USB-converter 3,3v and worked flawlessly for a long time. I replaced it with a new one but no go. In the beginning no problem, I could use SSH. Second thing is that the hard disk became erroneous. I bought a bigger model but no boot. I thought that the UUID-entry in /etc/fstab caused this and changed it via tune2fs to the old one, but still no boot. Thus I could no longer use SSH! And I cannot mount the old harddisk, it's to erroneous! Third thing is that I tried with a new image, and the cubie seems to fina…

Hi All, Armbian boots fine from SDcard but when I run nand-sata-install the script complains that it has no target. A #ls /dev/mmcblk* shows /dev/mmcblk0 and /dev/mmcblk0P1 When mounted, just to see, the mmcblk0P1 partition contains the usual linux directories, so I suppose this partition is definitely the SDcard No EMMC device is present. Could this be due to me performing, yesterday a: dd if=/mnt/ArchLinux_Minimal.img of=/dev/mmcblk1 bs=4M ? I did this because I read somewhere that booting up from SDCARD followed by a dd worked in some cases. Note I originally wanted to run Arch, but since there is apparently no support at orangepi.org, after…

Hi all, Firstly, I want to say that I'm new to Armbian and embedded Linux. I have tried searching the solution for my problem on various sites but I haven't had any luck. I am using a Nano Pi Duo 2 (H3) board with Armbian Buster to communicate with another device through UART1 (TX1, RX1). I am able to communicate at 115200 bps with no problem. However, I need the baud rate to be at least 230400 bps (ideally 921600) for my application. I'm using WiringNP library. When I changed to those baud rates and performed a simple feedback test (shorting TX/RX), I can receive the data. But when I connect it to another device, the communication does not funct…

I installed armbian latest release. When i shutdown system desktop closed. After 1-2 seconds, desktop opened again And after 1-2 seconds closed again. Why desktop is launched again after closed? Is it a problem? How can i fix that?

Hello, Armbian shows me very low wifi coverage and fail to connect, with other distros the signal is good, any solution? I use Jessie Desktop 3.4.112 Sorry for my bad english Thnks

Hello, I have done my iso with script yersterday and when I start the Orange Pi Plus 2 the yellow led appear but nothing else doing ... Why ?

Hello I have an orange pi pc2 device with armbian-release on it. Yesterday I was faced with strange error: My orange pi pc2 was shut down, in auth log file I see "Power key pressed. Powering Off... System is powering down." But there is no power key and no one can press powering off by console or interface. Temperature in error moment was OK = 57 C How it can be, why orange go to powering off by him self? Spoiler armbian-release: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.78 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 …

Hi, I have a question about distro upgrde. This is the information on welcome screen: Packages: Ubuntu stable (jammy), possible distro upgrade (noble) Support: DIY (community maintained) I checked the release info on https://www.armbian.com/orange-pi-plus-2e/ and the noble is available. I used sudo apt dist-upgrade and it found no upgrade. Is there any wrong with that? And how I can do the dist-upgrade except writing a new image?

I am using the latest Armbian image on OPI+. I had a requirement to read a 64Gb USB flash formatted under Windows with the extFat filesystem. Much to my surprise it didn't mount. I thought it was a hardware problem 1st. But then it appeared, that mount doesn't support the the extFat filesystem by default. It is necessary to add the extra packages, but I didn't succeed: root@orangepiplus:/# apt-get install exfat-fuse exfat-utils Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: exfat-fuse exfat-utils 0 upgraded, 2 newly installed, 0 to remove and 9 not…

Hello, first of all many thanks to all the community that keeps this project alive. I recently bought a NanoPi NEO2 board and of course decided to drop the OS provided by Friendlyarm and give a try to Armbian's Ubuntu build for this board. Everything seems to work just fine, however I'm unable to get a reading on the CPU Frequency. I tried multiple tools and commands but somehow all end up with something like "cpuinfo_cur_freq: No such file or directory. For instance, here is the output of armbianmonitor: armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armb…

My problem with Cubieboard3: input audio file hallo.mp3 with content "Hallo Otto" play hallo.mp3 --> Output on analog audio clipped to: plop lo otto plop It looks like the audio channel must be switched on and off for use. What can I do?

Basic information: Board: Orange Pi Plus 2e Image: Armbian_19.11.3_Orangepiplus2e_buster_current_5.3.9.img Issue: No sound on HDMI output There has been quite a few suggestions for this issue here and and OrangePi Plus and none works for me. Tried following: 0. sudo apt-get update && upgrade 1. Created and Changed /etc/asound.conf Version 1: pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } Version 2: pcm.!default { type hw card 1 device 0 } ctl.!default {…

Hi guys! I have a problem with Orange Pi 3. After a night leaving the small board turned on I reboot the board and try to use a Bluetooth connector it shutdown. Again and again the same problem. When I touched the board it was so hot. Even when I use outside the case the board can't support a process for at least 30 minutes without turning off. I got the outputs of dmesg. As I don't know, I am a replay newbie, I ask for help here. Best regards. Paulo

Has anyone had any success with running a current/semi current OS and the NAS/RTC Enclosure/Hat from FriendlyElec. I was never impressed with the NAS/OpenMediaVault image that shipped with the board/hat. I have attempted to strip OMV out of the device and move the device forward with some success. The the Kernel is stuck at v4.14.52. But I would prefer to load a clean current OS and potentially use the correct overlays to enable the extra USB Ports, USB to SATA Bridge and RTC features. Question is does anyone have any information/guide to use a current version of Armbian/Community and the correct overlay file(s) to allow the the JMicron USB to SATA interface and …

Hi there, I've been trying for a few hours now to get the GPIOs working with the mainline kernel (ARMBIAN Debian GNU/Linux 8 (jessie) 4.5.2-sunxi). According to the board layout photo, I am using PG0, PG1, PG2 and PG3. With the legacy kernel, they export as GPIO1-PG0 a.s.o. accordingly and work perfectly. So I calculate the GPIO pin number: G is 7th letter, 7 - 1 is 6, 6 * 32 is 192. GPIO192 exports fine, I can set it to output, change the value to 1 but there's no voltage! Can anyone help me, please?

Hey guys, I have a OP3 H6 and I cannot seem to find out why the 4 x USB ports are not working only the single USB next to the HDMI works. Any Ideas? Cheers!

Hi, I've installed armbian for Orange Pi 3 (Buster) Everything works great, and the system boots, I even copied to the EMMC for booting from the Flash. The only problem is that the status LED stays "RED" and doesn't turn "GREEN" right after booting, like it does in the orangePi official debian. How can I make it GREEN? Thanks Leon

Dear Sirs and Madams! I am trying to reconfigure https://github.com/friendlyarm/h3_lichee BSP's kernel via make menuconfig which is producing following .config file: # # Automatically generated file; DO NOT EDIT. # Linux/arm 3.4.39 Kernel Configuration # CONFIG_ARM=y CONFIG_ARM_HAS_SG_CHAIN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_USES_GETTIMEOFFSET is not set CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_KTIME_SCALAR=y CONFIG_HAVE_PROC_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GE…

Hi, my environment is: Orange Pi One ARMBIAN 5.34.171031 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i WiringPi fork by WereCatf: git clone https://github.com/WereCatf/WiringOP.git -b h3 ./build small c++ programm: #include <stdio.h> #include <string.h> #include <errno.h> #include <stdlib.h> #include <wiringPi.h> #include <pthread.h> static volatile int globalCounter; void myInterrupt(void) { ++globalCounter; printf("InterruptCounter: %5d\n", globalCounter); //digitalRead(7); } int main(void) { if (wiringPiSetup() == -1) { print…

IPv6 is not working correctly for me although my connection information seems right, I am not able to ping6 to google.com for example. IPv4 is working fine. Is this a known bug? Or does anybody know a solution to this problem? In the pictures below you can see what error I'm getting and also my connection information.

The module ds2490 seem to be missing in the new release. Should be: /lib/modules/4.19.62-sunxi/kernel/drivers/w1/slaves/w1_ds2490.ko

Hello! I have installed image Armbian_24.2.1_Orangepizero_jammy_current_6.6.20_minimal.img from https://www.armbian.com/orange-pi-zero/ Orange Pi Zero H2+ 256M There are only utils root@mobi:~# armbian armbian-add-overlay armbian-install armbianmonitor https://paste.armbian.com/ayoxebogog

Hi there # uname -a Linux orangepipc 3.4.113-sun8i #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 armv7l GNU/Linux #apt-get install pciutils-dev pkg-config #git clone https://github.com/flashrom/flashrom.git #cd flashrom #make CONFIG_INTERNAL=no CONFIG_RAYER_SPI=no CONFIG_NIC3COM=no CONFIG_GFXNVIDIA=no CONFIG_SATASII=no \ CONFIG_ATAHPT=no CONFIG_DRKAISER=no CONFIG_NICREALTEK=no CONFIG_NICNATSEMI=no \ CONFIG_NICINTEL=no CONFIG_NICINTEL_SPI=no CONFIG_OGP_SPI=no CONFIG_SATAMV=no No work! hooked: spi_mosi = port:PC00 spi_miso = port:PC01 spi_sclk = port:PC02 spi_cs0 = port:PC03 root@orangepipc:~/flashrom# ./flashrom -p linux_spi:dev=/dev/spidev0.0 flashrom v0…

As title says, i am try to get the flash thing going on the UART0 on the OPI Zero (the debug ports i guess). But i got no luck, anyone has any experience with this? Thanks:)

I've been trying to change the I2C clock frequency on a NanoPi Duo doing the following: cd /boot/dtb sudo cp sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dtb.old sudo dtc -I dtb -O dts -o sun8i-h2-plus-nanopi-duo.dts sun8i-h2-plus-nanopi-duo.dtb sudo nano sun8i-h2-plus-nanopi-duo.dts in i2c@01f02400 section change clock-frequency = <0x186a0> to clock-frequency = <0x30d40> (200 KHz) sudo dtc -I dts -O dtb -o sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dts reboot Looking in armbianEnv.txt I have overlay_prefix=sun8i-h3 and cat /proc/device-tree/model shows FriendlyARM NanoPi DUO. The issue is that no mat…

Hello, I wonder how to use built in microphone on Orange Pi one +? root@orangepioneplus:~# arecord -l arecord: device_list:272: no soundcards found... Thanks

I remember that the maximum frequency was 1296Mhz back with Xenial, with kernel 3.x. It even says here Heat is not a problem since i have a large heatsink and temperature controlled fan, i was just curious about why the max frequency was bumped to 1368Mhz on the newer builds. What's the rationale behind it?

I have orange pi zero board ..i searched a lot for changing boot splash screen ( currently "armbian universal operating system" which is enabled by adding bootlogo=true in armbianEnv.txt ) I have tried Plymouth it is not working After searching lot i knew about if we can replace bootsplash.armbian , it can help because then neither we need to change uboot packages nor we have to add quiet splash like words etc in armbianEnv.txt. https://github.com/armbian/build/tree/master/packages/blobs/splash. With help of this bootsplash-packer Can anyone list me some steps ( in short ) How to run this script and create…

hey, it is nearly everything said in the title. I want to use my cubietruck for playing streamed videos on my beamer. I don'T want to take my pc to the living room everytime i want to watch tv on my beamer, so i hope, there is a way to get the cubietruck working with vlc mediaplayer. Any tipps?

Hey all, Sorry for the noob question, I posted this in another topic but it hasn't seen any action so I thought I would make a post. I have an Orange Pi PC, using the RetroOrangePi build which is based on Armbian. I'm having overscan issues on my 720p TV. I checked the options on the PC, there's no way to fix it there. They figured it out in this topic here (where I initially asked this question): The solution is to add code to u-boot in order to solve the overscan, or edit boot.cmd. My question is, will using u-boot be the best solution, or is it better to edit boot.cmd? Do I simply create a boot.cmd in something like note…

Hi, I am trying to interface I/O expander MCP23017 to Nano Pi Neo2(Hardware specs:1 GB RAM, Gigabit Ethernet . Software specs: Debian Buster with Armbian Linux 4.19.59-sunxi64 ) . The issue I am having is I am not able to see the device when I run sudo i2cdetect -y 0 . I have enabled i2c overlays in /boot/armbian.txt . I am using 10 K Ohm pull-ups on SDA and SCK . I get no activity while running i2cdetect on the oscilloscope on SCK and SDA lines . Is this an issue with the kernel ?

Hi, I have a beelink X2 and did: apt-get update apt-get upgrade apt-get install -f apt-get update apt-get autoremove -y I think i have version 5.20. If i look at: cat /etc/*-release # PLEASE DO NOT EDIT THIS FILE BOARD=beelinkx2 BOARD_NAME="Beelink X2" VERSION=5.20 LINUXFAMILY=sun8i BRANCH=default ARCH=arm PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" So i think i have version 20 But if i do an: cat /proc/version Linux version 3.4.112-sun8i (root@xenial) (gcc…

Hi, I'm trying to make a hotspot with the beelink x2. I have some problems with resume after suspend. So i have a question about the beelink x2. Does anybody know if it is possible to start the beelink after a shutdown with the power-button. If i want to restart it, i have to re-insert the power-cord and the beelink will boot. Button does nothing. Thanks. Erik

We want to merge eMMC/non eMMC images and in theory, it should work. eMMC version works on my Lime2 but just to make sure I need some feedback from Micro with and without eMMC, especially most recent ones. Lime2 with or without eMMC https://dl.armbian.com/lime2/Debian_stretch_next_nightly.7z Micro with or without eMMC https://dl.armbian.com/micro/Debian_stretch_next_nightly.7z Thank you.

Hi Everyone After several weeks (maybe months) seeking for a solution for my problem I decide to post it here and hope to get a fix for it. At first I still run an Cubietruck with Armbian (everytime the latest Version) with just a few services (Pi-Hole, RPi-Monitor) and for future use Apache, MariaDB and PHPmyadmin (just installed and running, but with no content). Now to the problem itself: The Cubietruck runs approximatly 6 to 10 days and then it's get stuck. Only a reset solve the problem for the next 6 to 10 days. On every crash I checked the syslog and it always show the following lines as latest entries: Jun 29 15:17:28 localhost systemd[1]: St…

Ethernet was working fine for me, up until I rebooted the board. The LEDs on the ethernet port blink briefly during boot, but once booted they are off, and the board does not have an IP address. Via serial console I undid the change I made prior to the fateful reboot (adding 'overlays=uart1' to '/boot/armbianEnv.txt') and rebooted again, but to no avail. Having searched for the issue, I also confirmed that my power supply is sufficient; running 'stress -c 2 -m 2', and measuring across pins 2 (5V) and 6 (GND) of the 40-pin header, I get 5.05V. As I don't have a network connection, I did not run 'sudo armbianmonitor -u', but I gathered the following …

Gentlemen, I've spend time looking for the GPIO pinout for the Orange Pi Win I am using with Armbian. Specifically I would like to use SDA and SCL. Does Orange Pi publish some information on this subject? Thanks in advance for your information.

Hello, I'm following my investigation to make possible an Open Hardware & Open source solution for schools (cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-37422 ) I can't use the WiFi. I didn't found information on the forum for Orange Pi PC+ on board wifi (found some but it was for USB wifi). I have downloaded Ubuntu desktop – legacy kernel on https://www.armbian.com/orange-pi-pc-plus/ and installed it on class 10 SD card with Etcher ( Armbian_5.30_Orangepipcplus_Ubuntu_xenial_default_3.4.113_desktop.img). I'm using 3A 5V power …

Hello, first post here, so sorry if did not provide enough information. I need to change spi buffer length to 8192. So far tried: 1) modprobe spidev bufsiz=8192 creating the file /etc/modprobe.d/spidev.conf and adding to it the line "options spidev bufsiz=8192" When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 2) Add to /boot/cmdline.txt: spidev.bufsiz=8192 When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 3) cd /sys/module/spidev/parameters chmod 666 bufsiz echo 65536 > bufsiz did nothing. 4) /boot/armbianEnv.txt added options spidev …

Hello, After i made the Focal update i2c is very slow and armbian-config does not start. So I made a fresh installation with Armbian Focal mainline based kernel 5.10.y But no I have the same problem. What could be the reason? Is it possible too test the i2c bus? thx greetings

Hello everyone, I am using Orange Pi Zero LTS 512MB (H3 Cpu) hardware. As an image; I am using "Armbian 22.08 Jammy Kernel 5.15.y, Updated: Sep 24,202". The MAC address changes every time the Wi-Fi is turned on. I tried several different images. I tried a few simple fixes posted on the forums, but only managed to fix it for ethernet. But it was not successful for Wi-Fi. I need an image or solution that does not change the MAC address. Is there anyone who can help with this?