Allwinner sunxi

I use "./compile.sh BRANCH=default BOARD=orangepilite KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=xenial" to build the whole booting image for my orangepi lite, it works very good as the official prebuilt armbian image. Here, the usb otg port seems configured as peripheral mode already( g_searial module works as gadget in fact), I can use it as usb seraial well. However, I want to make it works as a usb storage, so, I though the g_mass_storage was the right module. I loaded it using following command: insmode g_mass_storage.ko file=/dev/mmcblk0p1 removable=1 then, I got kernel message like: [ 194.842091] usb open ba…

Hello All, I'm using a cubitruck and I'm still on 5.25 mainline. I just saw that there is already v5.30 available but there are no updates available. apt-get update && apt-get upgrade tells me there is nothing to update. What am I doing wrong? Gesendet von meinem LG-H815 mit Tapatalk

I hear that Orange Pi 2E has 1GB network speed and an USB3 port. In my project I paln to use an SBC as a network bridge and sniff traffic for problems. A simple network tap would otherwise be ok but they come only with 10/100Mbd speed limit. What I'd do have two ethernet ports on the Orange Pi, one regular and one via USB3. No to my question: are Orange Pi capable for this or is the advertised network/USB3 speed buggy/lacking? I have one Orange Pi PC for a file server and it has been running for weeks just fine. Raspberry Pi's are fine to (albeit still no 1GB ethernet). Raspberry Zero's have issues (mine seem to lock up after a couple of days).

Dont know whats wrong, but none of the images on the page are working, tried to burn them with ApplePI-Baker and Etcher, but no luck. Board boots fine with stock android image. There was someone in here that got it working with an image called Armbian_5.27_Orangepizeroplus2-h5_Debian_jessie_dev_4.11.0.img.xz but where do I download that image ?. And yes I know there is loads of problems, but wanted to test som perfomance on the board. Hope somebody can point me in the right direction

Hi, after the update from Armbian 5.23 to 5.25 on a Banana Pi M2+ board, the MAC address and CPU serial number have changed. This can be reproduced by just updating the u-boot package on Armbian 5.23: # ifconfig | grep HWaddr eth0 Link encap:Ethernet HWaddr da:c7:a0:49:24:d6 # grep Serial /proc/cpuinfo Serial : 2435501d0a0e4800004d # dpkg -i linux-u-boot-bananapim2plus_5.25_armhf.deb # reboot # ifconfig | grep HWaddr eth0 Link encap:Ethernet HWaddr 3a:89:a1:23:98:a6 # grep Serial /proc/cpuinfo Serial : 24005035871c481d0a0e Does anyone know the reason for this? Did u-boot change the way these numbers are generated? …

Hi, After reading a post about NAS for allwinner, I need some advices: So far I have same performance on my raspberry pi b+ and my orangepi2e : 2 hard drives 2 To 2,5" usb on a powered hub. (approx 11 Mb/s max through AFP/nfs share). Gigabit does not seem to be the bottleneck on the pi since it does not impact my bit rates. My question is simple : can I have better performance if I make a RAID via btrfs ? Do I have to format my hard drives ? What is the best distro ? (I used armbian but does not seem very stable compared to the raspberry, what about ubuntu server, or raspbian ?) Thanks

Hello, to all OrangePI PC enthusiasts. Well I'm in the community of those who definitely underestimated the Orange of the PI, but let me share my burden :-) for the fun of it. It started with the camera- gc2035 and vfe_v4l2 modules. Had to try a couple of images until I got it by luck I guess - after that I found out that every image I use is not capable of having a FTDI device connected to "ANY" USB Port (OK, you got me, I didn't try the microUSB and I won't). After that I tried no matter what I wanted to connect to USB it was not even recognized. Now I'm back in changing/swapping around Images until I found one that let me plug anything I …

Greetings, all! I've got a LeMaker A20 BananaPro, on which I'm using the Armbian mainline distribution (for a more complete description of my setup, please see below). I'm using a serial console to the board; I'm not connecting anything to HDMI for display. I'm running the distribution off of a brand new 8Gig SanDisk Extreme Pro. I would like to use alsa (at least in part) in the audio stack. I'm experiencing the following: When I have no audio playing through the audio out jack, I get a loud (powerline, probably) hum on my speakers. When I start audio playback (a wav through aplay, or an mp3 through mpd, etc.) the hum disappears, and the so…

Hi, im using an Orange Pi one with a camara. I bought it as a set: https://de.aliexpress.com/item/Orange-Pi-One-SET-9-Orange-Pi-One-and-Camera-Camera-with-wide-angle-lens-for/32660642513.html?spm=2114.13010608.0.0.8eWICb I've flashed armbian to the SD Card and fired it up. The Problem I have is, that I can't access the camara. Maybe I'm doing something wrong, or the camara is broken. What I've done so far, is following this tutorial: https://diyprojects.io/camera-2mp-orange-pi-unpacking-installation-test-motion/#.WSw0jbpuKUk and then red through following article: http://www.orangepi.cn/orangepibbsen/forum.php?mod=viewthrea…

Hi, This is my first post and I want to say thank you to all the developers and contributors of this great eco system. I've build an image for odroid xu4 with the openmediavault script. This is really great because the software packages and kernel ist up to date and running like a charm. Then I tried to get my DVB card working but that is work in progress. The card is not supported by the 4.9 Kernel and the usual way is to compile the media_build package from hier: https://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers But with an cross compiled system as armbian i…

Hello, my Orange Pi Zero CPU is constantlyrunning at 67-68-70°C (it is the same with/without passive cooler). Is this temperature ok for my board? Can I run it with this temperature long time (weeks, months, years)? Thanks for help.

Hello ppl. I have an Orange Pi Zero, and I have some issues using UART interface, it give me an output like this: ▒▒▒I▒%E▒Y=7▒g!=7▒Y=5▒[s▒i-''▒Y-9/▒Y=▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒Y=7▒c5!e=#=15Q=-▒a#'-#5▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒[5=9/57▒=5▒c5!-▒a'▒7==;=5▒57=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒}=9/5▒▒5;▒5▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒}7=#957▒muuu▒▒▒▒▒▒▒▒%=#=15%5#▒7=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒7-)▒5%5▒%!#-!▒7=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒Y=cW_▒7=5%!#▒▒▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒Y=7▒▒59▒▒'!9='▒y▒▒▒R▒%I▒▒▒▒%▒▒ai▒▒▒I▒%E▒Y=7▒gY{…

Hello, I'm trying to interface an I2C device to Orange Pi Zero with armbian. By running i2cdetect I obtain the following result: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- I've tried to load …

I've read many posts here and understand the OPi0 wireless chip isn't very well liked. I'm trying to setup hostapd with both client and AP functionality. I can get AP working only if I dedicate wlan0 to it. It seems that virtual devices (eg iw dev wlan0 interface add uap0 type managed; ip link set uap0 up) don't work with the current jessie image, making it impossible to have both AP and client simultaneously. I'm happy to help with testing the driver, but I'm no expert and certainly not knowledgeable enough to code this sort of stuff. If there's any help to be had, I'd be grateful.

Hi, I got a new nano pi neo air and wanted to add a microphone to record sound. First I tried my USB mic and it worked without any problem then I saw a topic in here: https://forum.armbian.com/index.php?/topic/3598-nano-pi-neo-air-mic-audio-out/ According to this topic, I can attach a mic to the pins that mentioned. But my big problem is what is the hardware name? I tried to use arecord -l and the output was: root@NanoPi-NEO-Air:~# arecord -l **** List of CAPTURE Hardware Devices **** card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 But it is the HDMI sound card which I think is…

Hello, I want to use the Banana Pi for VDR and need a dvb device - Geniatech T230 for example. Therefore I need i2c_mux enabled. On the 8. May 2017 I created a sd-card-image with your tool (virtualbox, ubuntu and "git clone https://github.com/igorpecovnik/lib --depth 1"), everything works fine. :-) But I forget to enable the remote controller adapter in the kernel... O.k., I started to rerun all the things and created a new sd-card-image. But the network is out of funktion. :-( The system doesn't reach the dhcp-server. The network with a static ip-adress is out of function, too. Anything was changed on the system, wasn't it? The…

Very grateful to armbian to provide such a good image！ Armbian has released many images that have been packaged with OMV。 I am follow this link for a long time：http://kaiser-edv.de/tmp/NumpU8/ I'm happy to see more and more mirrors available。 I used one of the images named OMV_3_0_72_Orangepiplus2e_3.4.113.7z and it works good，Special thanks to tkaiser！ There is another model（Orangepiplus2） that is better suited for NAS Because it has a sata interface https://www.armbian.com/orange-pi-plus-2/ Can Armbian provide OMV images of the above motherboards? At last, sorry for my poor English.

Hello guys here is a couple of questions regarding Mali/EGLFS on OrangePi One and Armbian v4.4.*. I am going to cross-compile and use Qt5 Embedded on Armbian v4.4.* and I strongly need QML engine for my development which requires eglfs plugin. Is Mali GPU supported on this version of OS ? How/where to get/compile user mode libraries (EGL+GLESv2) for this version of OS ? Thank you

When connecting my BPI-M2 the internet connects Wifi, so that there is no network cable connected to it, an interface "eth0: avahi" appears, so I do not have internet access. Can anyone help?

hi guys, I have reported this on to etcher folks at https://github.com/resin-io/etcher/issues/1466 Not sure if it's a feature or a bug. Cubie truck 3 Any ideas? Etcher version: Etcher-1.0.0-win32-x64.exe Operating system and architecture: windows 8 Image flashed: https://dl.armbian.com/cubietruck/archive/Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113_desktop.7z Do you see any meaningful error information in the DevTools? Filesystem Size Used Avail Use% Mounted on udev 941M 0 941M 0% /dev tmpfs 189M 5.5M 184M …

Hi friends, I have read a lot document about booting orange pi zero over usb flash. I flashed latest mainline u-boot to orange pi's SPI Flash. I can boot the system via the usb port which is next to the ethernet. Can I boot the system via the usb ports USB2 and USB3 that the h2+ has and the expansion card that can use it?. I can not see these USB's through u-boot terminal. thanks.

I think I know the answer to this but I'll ask anyways. Is there any command line software out there (e.g., VLC) that I could put onto an Armbian Server Edition version that would show a movie out on the HDMI port? I have a NanoPi M1 that has a HDMI port. But I'm assuming that without all the Desktop video driver, it isn't possible to do this on a headless server.

Hi Guys! I am experimenting with an Orange PI Zero H5 and have noticed that there is no CEC support in Armbian Is it something that is worked on and i should expect it to be present in the H5 Armbian builds anytime soon ? I have found some guides with Kernel Patches etc but i am a Linux noob and it's a nuclear physics for me atm. Anyone can clear that out for me ?

Good afternoon, I am using armbian 5.25 on orangepipcplus with legacy kernel. when visiting google.com site with firefox, I will only see the "mobile" site with restricted functionality. On the bottom of the screen there is a link "Google-Ansicht klassisch" which should bring me to the desktop version of google. But when pressing this a popup tries to come up but will not finish its presentation. Now this tab is blocked, I never get to accept google terms and conditions and can not use google. Do you see the same behaviour? Is there any known remedy? PS: Yes, I tried firefox "safe mode" - same thing! Thanks, gnasch

Hi, I am running the latest Armbian stable headless build with legacy kernel for a few weeks now without issue (tvheadend, cups, sane, shairplay-sync, pi-hole). Yesterday I added a dvb-c stick from sundtek which works pretty well. However, I noticed that only 1 USB port works (the one by itself). I can either connect the dvb-c stick or my printer/scanner. Attaching another device to either of the other 2 USB ports does not work... What am I missing?

Hi, I have serious problems with the 5.25 images of armbian on a cubietruck. After a fresh install and apt-get update apt-get upgrade I get errors with : dpkg: error processing archive /var/cache/apt/archives/linux-libc-dev_4.4.0-78.99_armhf.deb (--unpack) This is for the Armbian_5.25_Cubietruck_Ubuntu_xenial_next_4.9.7 image, with other images this concerns a different package. Only Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113 works. After this error, the filesystem seems to be defect and is remounted ro. On another try, I removed the rmount ro on error option from the fstab and the /var/lib/dpkg directory was corrupted. …

This I asked originally here, but in the wrong topic: Question: Now do these cheap but very popular BT Android/ iOS remotes-gamepads work on boards under Armbian, or Debian/Linux in general ? Quote this

I'm testing the GPS PPS function. If I use PA7 (GPIO PIN 12 in OrangePI Zero), get nothing. But if change to PA3, (GPIO PIN 15), it works well ether pps-gpio module or gpsd itself. Is any strange stuff on PA7?

Hi. I'm trying to change the setup I have running on a pi pc to my new pi pc2 running latest version of nightly (at least latest version of the packages) Every kernel version I tried does include the w1-gpio and w1_therm but it's missing the w1-sunxi that's required for it to work. Is it missing from the kernel or am I the one missing something?

Hi there, I have problem with recovering "sudo h3consumption -m 1200 -c 4" on Orange Pi Zero, where it activates just 2 cores. No idea why. When I used "sudo h3consumption -m 900 -c 1" it worked fine, but now, when I am trying to recover all 4 cores it activates just 2 cores. Which files h3consumption changes? (so I will be able to backup them with clean install and the restore them once needed to recover settings for all 4 cores). And I found out, that with "sudo armbianmonitor -m" it shows CPU changes 900Mhz, 1018Mhz (dont remember exact values) but now it just shows 480 P.S. I made backups of these files: sudo cp /etc/backup_2017_05_21…

Hello! Need help for installing KODI 16 or 17 on Orange Pi PC on Armbian 5.25 I managed to install KODI 15, but it's old and some of add-ons don't work anymore. When I tried to install KODI 16 I received errors on libcec4 and libshairplay Thank you in advance!

Hello I have a Problem with my Orange Pi I've started a update on my running Orange Pi Plus 2 when i suddenly had a Power Loss on my house. After I fixted my Power Problems the OPi won't boot anymore All what i from the Debug Port get is following in repeat: Spoiler U-Boot SPL 2016.09 (Oct 15 2016 - 14:24:41) DRAM: 2048 MiB Trying to boot from MMC1 Or with another Image: Spoiler HELLO! BOOT0 is starting! boot0 version : 4.0.0 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rt…

OK

Hello Armbian community. Recently, I decided do try new distros for the Cubieboard 2. and Armbian seemed to be a really good option. However, just booting the latest image started to cause problems. After writing the image with the proper software on a proper SD card as mentioned by this webpage, it just doesn't work at all. To be brief, I took pictures of what appears on the screen, first being what seems like to be an error displayed by text, then a really messed up screen, and finally the board shutting down by itself. I would appreciate any help or recommendations regarding this issue.

Is it possible to add some gpio chip select for support more than one chip select on board ? Loooked on https://github.com/armbian/linux ... ers/spi/spi-sunxi.c I am not found any support of gpio here. Also here https://github.com/armbian/linux/blob/sun8i/drivers/spi/spi-sunxi.h we can see that only one chip select can be used: /* About CS */ #ifdef CONFIG_ARCH_SUN8IW1P1 #define SUNXI_CS_BITMAP(ch) (ch%2 == 0 ? 1 : 3) #define SUNXI_CS_NUM(ch) (ch%2 == 0 ? 1 : 2) #endif #ifdef CONFIG_ARCH_SUN9IW1P1 #define SUNXI_CS_BITMAP(ch) (ch == 3 ? 7 : 1) #define SUNXI_CS_NUM(ch) (ch == 3 ? 4 : 1) #endif #ifndef SUNXI_CS_BITMAP #defi…

Hello, With wheezy and I can't use CB2 build in /dev/ttyUSB0. cannot access /dev/ttyUSB0: No such file or directory What should I do to enable it and use it?

I have an external audio card connected to usb lsusb Bus 007 Device 014: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controller I have a problem that after rebooting the system ... Once it is detected and another time it is not :-( dmesg|tail [ 40.820066] usb 7-1: device descriptor read/64, error -62 [ 41.110045] usb 7-1: device descriptor read/64, error -62 [ 41.400108] usb 7-1: new full-speed USB device number 11 using sunxi-ohci [ 41.580056] usb 7-1: device descriptor read/64, error -62 [ 41.870068] usb 7-1: device descriptor read/64, error -62 [ 42.150067] usb 7-1: new full-speed USB device number 12 using sunxi-ohci [ 42.570119] usb …

I did manage to use the rmbian_5.27_Orangepizeroplus2-h5_Debian_jessie_dev_4.11.0.img.xz image and things boot fine. I also get pretty console on hdmi. But no network, and I don't have a way to get the keyboard on. Any suggestions on what kind of an adapter I need to get power AND usb keyboard to the thing (since there are no extra ports on it)? Or is it serial? Good recommendation on proper 'converter". I did modify the initial armbian_first_boot to enable wifi with proper ssid / password, and even enabled static, but no dice. Thomas

Hi friends, I am trying to downclock my OPi Zero and set/disable unused cores 1,2,3, limit DRAM speed, limit max cpu core frequency, put voltage down. Is this possible on Opi Zero? I tried e.g. but when I cat /sys/devices/system/cpu/cpu3/online is is always 1. Any idea please? Some advice how to do all of this is highly appreciated. I am trying to downclock Opi Zero to push produced heat down.

I am trying to figure out how to make the Orange Pi Zero a USB gadget. Preferably a USB Vendor Device but a mass storage device would work for now. I was able to successfully create the ethernet gadget. (Using Armbian_3.4.112_g_ether_kernel.tar.bz2) That is pretty cool. But I would like the mass storage or vendor device. I was playing around with modprobe but I am not really sure what I am doing. Module g_mass_storage is not found. I have searched this site and online for the last few hours and just got more confused. Thanks for any help.

I have a rtl2838 based DVB-T dongle which was working beautifully under 3.4.112 on my cubietruck. I upgraded a couple of days ago and now I don't get any video data, although the dongle is still recognised. I see 113 includes a fat patch to the rtl2832 driver. Is there some way I can back that out, or a safe way to go back to 112?

Hi, I bought an orangepi zero H5 and I try to setup armbian on sd card. I write the image with etcher but there is no screen display when I boot. I wait long time about 10mn, my card is 16Gb, but no display on my hdmi tv. I test Armbian_5.27_Orangepizeroplus2-h5_Ubuntu_xenial_dev_4.11.0 , and the nightly build Armbian_5.27.170520_Orangepizeroplus2-h5_Ubuntu_xenial_dev_4.11.1 but it is the same story: no display. I test the official Ubuntu from Orangepi there is no problem, the boot is fast and I get display on my tv. Do you have some advice ? Thanks. G*

Hello world, this is my first visit in this forum and my first question, please don`t bite me, if somethings wrong (and sorry for my bad englisch too, I`m from germany, blackwood forrest....). I am using my cubietruck now since may 2014, everythings ok. Now i got a week holiday and i thougt about an update for my cubietruck, it`s not about the ubuntu 14.04, it`s more about my old 4 GB SD-Card. OK, 10 EUR and i got an new 16GB Card "up to 80 MB/Sec." which i dont believe, but the problem is at another place: + first writing the image to the new 16 GB card: https://dl.armbian.com/cubietruck/Debian_jessie_next.7z + next backup the old…

My third Orange Pi Zero came last week, yesterday I plugged it and had heating issues... So I started reading, learning and testing.... Setup: OPiZ-1: 256 MB, no SPI flash - Has extension board plugged - for comparison OPiZ-2: 512 MB, with SPI flash OPiZ-3: 256 MB, with SPI flash (new one with problem) Test conditions: All with (newish) Sandisk Ultra 16 GB Class 10 All new formatted (SD Formatter) and burned/validated (Etcher v1.0.0) with Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img All on my desk - side by side, ambient temperature 25.0-25.1 C (20 cm from boards, no air flow) No case, no pass…

What is the latest version of Armbian tested and proven working with a gc2035 camera module, please? I tried a few months ago and ran into so many issues, I gave up. Camera works in Android, didn't work in the Armbian I tried, and was eventually advised to try an earlier version that I couldn't easily find. I decided to defer the problem, but it is now more pressing. Thanks in advance for info and advice. Regards, Charlie

Hello! How exactly connect this device: ENC28J60 ethernet over SPI. Not understand about INT(IRQ) pin - is where number mapped this pin to plug in Zero and how configure FEX?

Hi, I am new to development on Orange Pi and as such new to the concept of overlays. For the application I want to run on Orange Pi, I need to disable all USB ports (host an OTG), bluetooth, HDMI and audio out. Is there a way to do it using overlays? Or can I use sunxi-pio utility for the same? I am using nightlu build of Debian Jessie with kernel 4.10.3 Appreciate any help. -Sunil

Just got mine Prime and installed on microsd Armbian-server for that. After setting up root password and new user, have edited /etc/network/interfaces to have uncommented these lines source /etc/network/interfaces.d/* auto eth0 iface eth0 inet static address 192.168.0.106 netmask 255.255.255.0 gateway 192.168.0.1 dns-nameservers 8.8.8.8 8.8.4.4 auto lo iface lo inet loopback every manual says it should be easy like that... but it doesn't work where to dig next?

Anyone know if this is possible? I've tried this: https://www.raspberrypi.org/forums/viewtopic.php?f=36&t=138730&start=25, but when I go to start hostapd, get this: nl80211: Could not re-add multicast membership for vendor events: -2 (No such file or directory) Could not set channel for kernel driver Interface initialization failed uap0: interface state UNINITIALIZED->DISABLED uap0: AP-DISABLED uap0: Unable to setup interface. uap0: interface state DISABLED->DISABLED uap0: AP-DISABLED hostapd_free_hapd_data: Interface uap0 wasn't started nl80211: deinit ifname=uap0 disabled_11b_rates=0

Orange Pi Plus 2e How do I clone the SD card and both have boot capability? I am new to the concepts of Pi's so I am looking to slowly add abilities to the pi and have a working clone which I can use when I stuff it up. I have also seen no mention of grub being used anywhere. My main computer is a amd 64 with Debian running but I can use my laptop with win 8.1 on it but would prefer a solution which I can use on Debian Thanks for your help Dave

I received my new Orange Pi Plus 2e and tried to set it up. I already got an Orange Pi PC2 running so it's not really something new to me. I used the latest Armbian images (desktop and server), flashed them to my SD card (with Etcher) and plugged it into the Pi. The green LED lights up and the device seems to be working. To this point it's the same as on my PC2. But after ~1min the red LED starts flashing twice over and over and nothing seems to be working. I get no signal over the HDMI out and the LED keeps flashing. I flashed the SD card three times to make sure it's not a flashing error. I tried the desktop image twice and the server image once. It always ends wit…

The Problem is retry count exceeded... I don't know why is this happening to me. I search the older post the same problem, but i don't know what is the exactly problem. My board is CubieTruck3 A20 Board and i use SD Card.

I'm sorry for the lame question, I just don't wanna regret anything before buying this fan, so I'm talking about this fan (3cm x 3cm) Spoiler I want to mount this fan right below the board by just screwing it in. Do the holes fit perfectly with the holes of the opiz board ? I've asked this before on facebook but someone suggested me to just glue the fan directly onto the board but I'm afraid it'll damage the board instead.

Dear.I run for years on my cb2 a home automation system..Only now i need some more power. [ my cpu is running to his max ]Can i speed up the cpu of the CB2?I hope that there ia someone that can help me to let live my cb2 longer..Thanks..

Today I encounter a rather significant packet loss at the wired ethernet connectionmy at my NanoPi NEO. The device is up-to-date running with Armbian 5.25 and Pi-hole. The system is the most of time idle and shouldn't suffer from heavy load or many simultaneous connections. From NanoPi NEO to Windows: --- 192.168.0.204 ping statistics --- 263 packets transmitted, 221 received, 15% packet loss, time 262004ms rtt min/avg/max/mdev = 0.358/0.457/0.729/0.049 ms From Windows to NanoPI NEO: Ping-Statistik für 192.168.0.10: Pakete: Gesendet = 249, Empfangen = 222, Verloren = 27 (10% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 0ms, Maximum = 0ms, Mi…

I booted up my OPi0 + $2 expansion board this weekend after reading through the doc on it warning about TVout problems. Used the legacy Xenial 5.25 build available. I used the USB-serial method and logged in from my PC via SSH later over WiFi. On the TV there was no desktop GUI display, just the regular login prompts CLI. So this is not a RCA composite cable issue, but likely a display one...my TV is 720p. 1. On the TV I just got the login prompt after the text based Orange Pi Welcome screen. After logging in it stays text, as if I were in Terminal. I tried to install: $sudo apt-get xorg lightdm xfce4 tango-icon…

Hi everyone, i want to wake up orange pi on any gpio pin. Current i only can wake up from button on orange pi. There is a section of wakeup_src_para in fex configuration file, but when i append a wakeup_src with any gpio port, does not effect anything to wake up. how can i do?

Hello Today i download Orangepi Zero Plus H5 Armbian OS then i tried gpio - i2c test but it's not work ... I did like this sudo apt-get install python-dev sudo apt-get install python-smbus sudo apt-get install i2c-tools sudo apt-get install libi2c-dev sudo nano /etc/modules -> add - i2c-dev, i2c-bcm2708 and i refer https://github.com/longsleep/linux-pine64/pull/17/commits/d915860a9c57a9a3ab3df7775c942ca205c8e16d this site i think adding I2C configs is not problem so give me some advice

Ping too high(OrangePi Zero) Armbian_5.25 What could be the problem?

Good day. I've purchased lcd 5'inch LCD. I have some troubles with HDMI connection (no image), but i fixed it using this topic: link. (drivers at disk doesnt take any effect) But i can not run touchpad. I used different hints but god no effect board - Orange Pi PC Plus kernel 3.4.113-sun8i module ads7846.ko at /lib/modules/3.4.113-sun8i/kernel/drivers/input/touchscreen My script bin: Spoiler [spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3&g…

Hi Does anyone know if the OPi Lite's WiFi is meant to automatically reconnect if the AP reboots or disappears and then comes back? What is the default behaviour supposed to be? Is it meant to automatically scan nearby networks? Thanks

Hello, actually i have "Bananian" with the kernel "3.4.113-bananian", and I would like to switch to the Armbian mainline kernel! My problem / question is how does it work with the GPIO in the mainline kernel? I use these commands under the legacy kernel... (I use the modified WiringPI from LeMaker) echo "17" > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio17/direction echo "1" > /sys/class/gpio17/value But these unfortunately no longer work under the mainline kernel! I don't understand how i calculate now the right GPIO Pin. (http://linux-sunxi.org/GPIO#Accessing_the_GPIO_pins_through_sysfs_with_mainline_k…

Dear All, I try to use the UART3 on my Orange Pi mini but it just won't work. I put a jumper on Pin 8 and pin 10 on the header. Also give read/write premmission to all users. Based on this UART3 is /dev/ttyS2 [ 0.000000] console [tty1] enabled [ 0.954713] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A [ 0.985810] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A [ 1.016890] sunxi-uart.3: ttyS2 at MMIO 0x1c28c00 (irq = 36) is a U6_16550A [ 1.047968] sunxi-uart.7: ttyS3 at MMIO 0x1c29c00 (irq = 52) is a U6_16550A [ 6.014770] systemd[1]: Expecting device dev-ttySAC2.device... [ 6.681738] systemd[…

Hi My cubie2 with a 2.5" HDD has exception Emask 0x10 SAct 0x80000 SErr 0x90300 action 0xe frozen [182296.803589] ata1.00: irq_stat 0x08400000, interface fatal error, PHY RDY changed [182296.803605] ata1: SError: { UnrecovData Persist PHYRdyChg 10B8B } [182296.803624] ata1.00: failed command: READ FPDMA QUEUED errors sometimes, which causes shutdown, spin up for HDD, with a big click sound, and it's not good for it. So i would try if it happens when the sata link is set to slower. But how can i do that?

I looks like there are more as one way to setup kodi on orange pipc. The latest version 17.1 of kodi with hardware exsaleration would be preferable. I wanted a setup where i could use the on board ir and some Remote i already own. Then an usb Keyboard. And i did not want that kodi starts at system start. I also wanted VNC be usable to do a login via VNC to be able to remote control from my Leptop. I did get Kodi 15.2 working but with drawbacks: Video is not smooth, not relay nice to view. VNC and IR did work and i could go back to the desktop to start internet browser or something else, all rather slow. Colors of the HDMI TV look …

Hello, first of all many thanks to all the community that keeps this project alive. I recently bought a NanoPi NEO2 board and of course decided to drop the OS provided by Friendlyarm and give a try to Armbian's Ubuntu build for this board. Everything seems to work just fine, however I'm unable to get a reading on the CPU Frequency. I tried multiple tools and commands but somehow all end up with something like "cpuinfo_cur_freq: No such file or directory. For instance, here is the output of armbianmonitor: armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armb…

As a newbie struggling for a month trying to find resources to set a static IP for Wifi DHCP and to get my PC to directly communicate to my OPZ via ethernet so I can be mobile... I am ecstatic to stumble across this solution, and had to share. Basically all you need to do is add a few bits of info to the /etc/network/interfaces file that is first made to setup wifi on the OPZ (https://www.youtube.com/watch?v=8zGRAPguaSQ). Here is the modified /etc/network/interfaces file contents that worked for me, in blue: auto lo iface lo inet loopback auto eth0 allow-hotplug eth0 iface eth0 inet static #last wor…

Hi to all! I'm taking my first steps with an Orange Pi PC+. Before I did projects with raspberry pi, but the extra functionality provided by emmc memory has made me decant for orange pi. So my problems are related to the compatibility of gpio functionality. I have two SPI devices (TFT and RFID reader), and I want use PA21 pin for SPI1_CS. I changed /boot/script.bin file for second SPI activate adding this lines: [spi1] spi_used = 1 spi_cs_bitmap = 1 spi_cs0 = port:PA21<2><1><default><default> spi_sclk = port:PA14<2><default><default><default> spi_mosi = port:PA15<2>…

Hi orange pi +2e with Distribution: Ubuntu 16.04.2 LTS Kernel version: Linux 3.4.113-sun8i armv7l rpimonitor installed with sudo armbianmonitor -r I use Rpimonitor to control temperature, upgradable packages and cpu frequency, nice tool ! Unfortunately it looks that rpimonitor has access to my external external hard drives, so no spin off . I change rpimonitor config files sudo nano /etc/rpimonitor/data.conf #include=/etc/rpimonitor/template/sdcard.conf and sudo nano /etc/rpimonitor/template/Allwinner_H3_Extended_Mainline.conf #dynamic.7.name=externaltemp #dynamic.7.source=/tmp/externaltemp #dynamic.7.regexp=(.*) #dynamic.…

The device gets unbearably hot as soon as it gets turned on, after ~30 seconds the Ethernet ports start to flash and the red light flashes for ~.5 of a second. I'm assuming it's toast, right?

Hello everyone, today I would like to show you how to compile Clementine on an Orange Pi PC (or PC Plus). I'm writing this because I couldn't find anything related to this topic on the internet, so I wrote this not very detailed guide. Step 1: Install all required dependencies for Clementine sudo apt-get update sudo apt-get install liblastfm-dev libtag1-dev gettext libboost-dev \ libboost-serialization-dev libqt4-dev qt4-dev-tools libqt4-opengl-dev \ cmake libgstreamer1.0-dev libgstreamer-plugins-base1.0-dev \ libglew1.5-dev libqjson-dev libgpod-dev libplist-dev \ libusbmuxd-dev libmtp-dev libcdio-dev \ protobuf-compiler libprotobuf-d…

How can I disable or lock my opi + 2e's microphone with a password to prevent anyone from hearing thnks

Hi everyone. I heard Armbian was the to-go distribution for the Nanopi NEO Air. I've got a bunch of these boards where I'd like to use the built-in Bluetooth and Wi-Fi capability in a small form factor for a project. I don't need video or audio or other functionality. I see a legacy kernel "stable build" and a mainline kernel "experimental" build. For the experimental build it lists the following known problems: No Mali drivers No hardware accelerated video decoding schedutil CPU governor may cause clicks and pops on audio output – change(d) to ondemand to work around this issue This sounds fine with me. I need no video, and…

Hi, I installed the main line kernel for Banana Pi and connected a USB/Wifi dongle. The device connects correctly to the wireless network but becomes unreachable after a while. When the issue occures and I try to ping the device, it answers the first ping and then becomes unreachable, via Wifi interface but also via the ethernet interface. I can wait for an hour or so, then I can do a ping (only one) then the device becomes unresponsive. I have to restart the device (power on/off) in order to be able to connect via ssh, but I can work for a few minutes only, then network goes down again. I don't have a screen to connect to the…

Hi, Recently I upgraded /sudo apt-upgrade/ my armbian and my wlan is now gone /it worked perfectly before/. Looks like xradio module is missing from the new kernel? I am trying to download driver from http://linux-sunxi.org/Wifi, especially from http://kaiser-edv.de/tmp/lGtv38/patch-add-support-xr819.tar.gz .... but the site is not working.

I just recently acquired a few Orange Pi Zero Plus 2 boards. I need to get them working for a Bluetooth application. After a somewhat rough start with the WiFi they appear to be running smoothly now. The first problem I am noticing is that sata-nand-install does not exist on the distribution for the H5. Can anyone shed some light on what is necessary to get these boards to boot from eMMC? Is there anyone currently working on this problem? If not, what is the correct version of that script that I should download to begin trying to port it, and what utilities will I need to adapt to make it happen? Any advice on how to begin? On another front, doe…

I'm trying to set up my OPI PC+ with a static IP address on wlan, but it doesn't seen to be working. This is my /etc/network/interfaces file: allow-hotplug wlan0 iface wlan0 inet static address 192.168.25.160 netmask 255.255.255.0 gateway 192.168.25.1 dns-nameservers 8.8.8.8 8.8.4.4 wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf I tried both with wpa supplicant line commented and non commented, but every time I boot up the board, it is still with the DHCP address.

Hi! Thanks for your amazing work, i'd like to have knowledge to give a hand After a few problems I've been able to boot my new Orange Pi Prime, but no keyboard is working on it. I've tried with an USB keyboard and a bluetooh one, but there is no way to make them work. No clues on dmesg, lsusn looks fine... Any idea about hoe to debug it?

Hi, After running the default image with legacy kernel for a few weeks, I am now trying the run a fresh SD card with the latest build of the mainline image. However, the MAC address of my device appears to be changing after each reboot - and I am running about of ideas to fix this issue. What I've tried so far: - Edit script.bin & add MAC address in the [dynamic] section - Edit armbianEnv.txt - Define an address in /etc/network/interfaces So far, I have not been able to solve the problem. Your help is much appreciated. Any suggestions on possible fixes for the issue?

Hi everybody, I have an OPZ board (256 mb). I couldn't manage to start work wifi in automatic mode. I tried manual configuration then tried nmtui in both cases wifi starts only after Ethernet plug was connected. OS: ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i How can I solve this problem? Thanks!

Hello, I am using Orange Pi PC Plus with Armbian Nightly. Since upgrade to kernel 4.11.0 audio stopped working, on kernel 4.10.11 everything was alright. When I am trying to open alsamixer i get error cannot open mixer: No such file or directory Can I fix it somehow? Can I still get last image with 4.10.11? Unfortunately it's not available at download page (too late).

Hi, I've tested Armbian this week-end to replace my Cubian distro, and I failed to get the sound out of my speaker. I went back to Cubian X as sound works with stock image. Anyone could help me with it please ?

Hi first of all Please excuse my poor English ! I install ubuntu lagecy server on my orange pi pc + and then install it on nand using : $nand-sata-install now when i power on my board with sd card (sd card without any image file) my root file system will mount on mmcb1k0p1 and if I insert my sd card after power on root will mount on mmcb1k1p1 (I now both mmcb1k1p1 & mmcb1k0p1 are my emmc) Now i need to automount my sd card and in my case I insert sd card before power on and as a result I add this line in fstab file #/dev/mmcb1k0p1 /mnt ext4 0 1 but it doesn't work ! how can i …

After figuring out how to enable analog audio on the Lime2 (https://forum.armbian.com/index.php?/topic/4224-analog-audio-on-lime2-with-stable-kernel-version-49/), I now have the problem that there is a clearly noticeable mainline hum whenever no sound is playing. The hum goes away as soon as any sound is playing on the device, and it returns a couple seconds after the sound stopped. It appears like some kind of power saving feature kicks in. With the legacy kernel the hum goes away during boot and does not return. Any ideas?

Hi, Creating a build for OPiPCPlus, mainline/dev/4.11, xenial,desktop. Need to enable the UDA1380 device in my local kernel build, yet I see some ..obstacles.. Tried initially to do a KERNEL_CONFIGURE="yes" in compile.sh but after started the compile and reached the point of menuconfig the UDA1380 option did not got presented (might be because there is no tristate string in mainline sound/soc/codecs/Kconfig..) so I reverted it back to normal. After the first attempt, I tried by modifying the lib/config/kernel/linux-sun8i-dev.config and added "CONFIG_SND_SOC_UDA1380=m", tried the compile again and waited to finish, yet at the end, although the ot…

Orange Pi Zero has two LEDs in the ethernet port and I want to control those leds for system notifications, right now I'm running OpenWrt on the OPiZ and I just need to know which file I have to trigger the LEDs. In GL.iNet router I can control the LEDs by doing echo default-on > /sys/devices/platform/leds-gpio/leds/gl-connect:green:lan/trigger But I don't know how to do that in OPiZ. Please tell me which file I have to edit in order to control the LEDs of the OPiZ

Hi, I have an Orange Pi Zero (256MB) board. I downloaded the prebuilt image named as "Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113.img" and used it without a problem. Then I cloned the project from github and cross compiled on an Ubuntu 16.04 computer (4.4.0-31-generic kernel) by using the "compile.sh" script. It created an image named as "Armbian_5.27_Orangepizero_Ubuntu_xenial_default_3.4.113.img". But this image halts after printing "ion_reserve_common: ion reserve: [0x47e00000, 0x50000000]!". You may find the log at the end of this post. I compiled the same project (5.27) with development kernel. It created the image name…

It used to function fine, however after not using it for awhile it has quit working. It starts booting normally, then hangs with what's visible on the screen being a bunch of systemd messages, with the last being either something about system variables or mounting FUSE file filesystem, when it's the latter it's followed up with a kernel panic. I've reflashed several times using both the server and desktop images freshly downloaded, no difference. The power supply I'm using worked before, as did the SD card. Unfortunately I have no way of showing you system logs or such for the time being. Any help would be appreciated.

While analog audio output (through the GPIO connector) works out of the box using the legacy kernel 3.4.113-sun7i, I could not get it to work with the stable kernel 4.9.12-sunxi. Since the driver is not activated in the stable kernel, I added the following to the dts: &codec { status = "okay"; }; This lead to the following `dmesg` output: sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok `aplay -l` gives: **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 However when I play back some audio file, no sound is genera…

Hello, I run Armbian (Ubuntu) on my Banana Pi Pro. -> uname -a Linux bananapipro 4.10.12-sunxi #7 SMP Wed Apr 26 02:44:12 CEST 2017 armv7l armv7l armv7l GNU/Linux Since the last days the boot process stops. The BPP shows the followings lines on screen: [ 10.943882] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d [ 11.233049] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30) [ 13.348258] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30) [ 100.212252] rc_core: Can't enable IR protocol cec After second 100 I'm asked for the root password t…

Below are supplementary quotes helpful to asking the question: can CPU presets be made into a desktop shortcut that could allow pre-defined CPU freq settings whether onthe fly or even reboot required? Is so, what would the code be? That's the question I can't answer. I ask because of the two Beelink X2s (one each of Armbian flavors); I'd like to get a hands-on feel for how high the temps can be expected to go. I probably won't be running hot for long, but then again I just received a bag of heat sinks and can also drill holes in the plastic box for better air circulation. QUOTE 1 for reference: Some boards allow to adjust CPU speed. nano…

Hi, I have an Oracle PI PC+ which will not boot without the hdmi connected. If you disconnect the hdmi once the board has booted it crashes or at least stops responding to ping/ssh over the ethernet. I've used pretty much all the builds I can find on armbian.com including the nightly builds with don't show a display at all but still fail without the hdmi. I've also tried booting from SD card and the emmc almong will messing with the /boot config files such as setting the console to serial and can't see anything interesting in the messages file. It shouldn't be a power issue as I'm using an Anker 2.4a PSU but I've tried other PSUs as well wit…

Hello together sorry for this long description but I want to provide all information I could save. I'm running armbian since 2(?) years and had never a serious problem with it. Today the system was not reachable anymore (services, ssh, ping) so I rebooted the server. Rebooting worked but all my data is on an external encrypted harddisk which I couldn't open anymore: root@MyCubietruck:~# cryptsetup luksOpen /dev/sda1 MyEncryptedHarddisk Enter passphrase for /dev/sda1: device-mapper: reload ioctl on failed: No such file or directory Failed to setup dm-crypt key mapping for device /dev/sda1. Check that kernel supports aes-xts-plain64 ciphe…

Hello, I have a 4x20 LCD display (with an HD44780 compatible adaptor) connected to my Banana Pi. It is running (freshly installed, switched from Bananian) on the mainline kernel: Linux bpi 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l GNU/Linux However, the display is not recognized. I checked the wire connections multiple times, they're okay and the backlight is on. So I assume this is a software issue. The output of "i2cdetect -y 1" is: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- --…

i downloaded the desktop for opi one and on first boot it wants me to change password but gives error msg and doesnt take new password

Hello, I try to setup my Orange Pi Lite with a thermal printer (http://www.ebay.de/itm/122418910118?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT). With my Arduino the printer works perfect, so it is actually ok. I just can't figure out how to use the ttl connection. I installed pyA20 and try to implement a kind of SoftwareSerial and it didn't worked really well: #!/usr/bin/env python """Basic blinking led example. The led on A20-OLinuXino-MICRO blinks with rate of 1Hz like "heartbeat". """ import os import sys import time if not os.getegid() == 0: sys.exit('Script must be run as root') from time import sleep from pyA20.gp…

sometimes the OrangePi PC freezes and I see the following error in kern.log May 6 11:17:14 orangepipc NetworkManager[554]: <error> [1494058633.9922] platform-linux: do-add-ip4-address[2: 10.45.168.13/24]: failure 17 (File exists) I use static! ip in my OPi and there is no other device using the same ip eth0 Link encap:Ethernet HWaddr 66:9b:7a:fd:fb:59 inet addr:10.45.168.13 Bcast:10.45.168.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2731 errors:0 dropped:24 overruns:0 frame:0 TX packets:3476 errors:0 dropped:0 overruns:0 carrier:0 …

hi, as of this morning, i tried updating my NanoPi Neo build (kernel=dev, os=ubuntu xenial, type=no graphics/server). Has been building fine for months. I think problem is in U-Boot (header missing ?) LDFLAGS="" python ./lib/libfdt/setup.py \ "-Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -include ./include/libfdt_env.h -idirafterinclude -idirafter./arch/arm/include -I./lib/libfdt -I./tools -DUSE_HOSTCC -D__KERNEL_STRICT_NAMES -D_GNU_SOURCE " lib/libfdt/fdt.c lib/libfdt/fdt_ro.c lib/libfdt/fdt_rw.c lib/libfdt/fdt_strerror.c lib/libfdt/fdt_wip.c lib/libfdt/fdt_region.c lib/libfdt/fdt_sw.c tools/libfdt_wrap.c tools/libfdt_wrap.c:147:21: fatal error:…

I have usb 802.11b/g that works as i plug it in UBUNTU Desktop on ACER Laptop. works on Armbian for OPIPC but doesn't work on RetroPie PC. on Desktop it is working with RT2800usb driver. Chip itself is RT2070L. on Retropie PC, it is listed when I'd LSUSB. I'd tried to download .deb driver for it but unsuccessful. what's other options do i have?

The following wifi dongle does not work with legacy kernel: Bus 002 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter $ uname -a Linux bananapi 3.4.113-sun7i #40 SMP PREEMPT Thu Feb 2 01:44:33 CET 2017 armv7l armv7l armv7l GNU/Linux Freshly flashed Armbian_5.25_Bananapi_Ubuntu_xenial_default_3.4.113_desktop