Allwinner sunxi

Hello, How to shutdown or reboot correctly with armbian jessie server 5.25 on Beelink X2 ?

Hello, bit of a strange one here. Using Armbian 21.02.3 Bionic with Linux 5.10.21-sunxi on a NanoPi Neo Core. Using nmtui to set a static IP on the Ethernet interface and all is good. On reboot, a second interface is added (dhcp) and the static interface disabled. Any help at keeping a static IP that survives a restart would be very much appreciated, Cheers Rob

Hello, How to enable the TouchScreen from olimex on olinuxino micro ? The display work fine, but the TS version do not control the mouse. the original distro from olimex works with TS, but how to enable TS on armbian ? (really better than olimex distro) Thanks.

Hello guys, at first I want to says thanks for the great OS that you deliver. I use it since 8 months on a bunch of nano-pi neo2's and it runs rock solid. However i rebuild from time to time the image I use from scratch in order to see that the installation is reproducable and repeatable. Today it has encountered that the installation of 'apt-get install python:armhf python-dev:armhf' failed with: # dpkg --add-architecture armhf # sudo apt-get update .... Reading package lists... Done # sudo apt-get install -y python-pip python:armhf python-dev:armhf Reading package lists... Done Building dependency tree Readin…

Banana Pi M1+, kernel 4.19.38-sunxi, Debian stretch I needed to get bus i2c-2 working so I went to armbian-config, ticked i2c-2. After reboot I found some information from PMU were missing, some i2c buses were removed and some added. before crw-rw---- 1 root i2c 89, 0 May 26 18:24 /dev/i2c-0 crw-rw---- 1 root i2c 89, 1 May 26 18:24 /dev/i2c-1 after crw-rw---- 1 root i2c 89, 2 Jun 11 10:29 /dev/i2c-2 crw-rw---- 1 root i2c 89, 3 Jun 11 10:29 /dev/i2c-3 crw-rw---- 1 root i2c 89, 4 Jun 11 10:29 /dev/i2c-4 armbianEnv.txt verbosity=0 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=078696…

Hi, i would like to read continously from Orangepi zero SPI. I download the latest kernel from https://www.armbian.com/orange-pi-zero/. Now i need to enable the SPI. I tried with changing my /boot/armbianEnv.txt file here i'm attaching it. Then i reboot and loged then i can see spidev0.0. But i want to use SPI1. How to enable SPI 1. armbianEnv.txt

cant build dahdi on armbian 5.2 how it make on arm? /usr/src/dahdi-linux-complete-2.11.1+2.11.1# make all make -C linux all make[1]: Entering directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux' make -C drivers/dahdi/firmware firmware-loaders make[2]: Entering directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi/firmware' make[2]: Leaving directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi/firmware' make -C /lib/modules/3.4.112-sun8i/build SUBDIRS=/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi DAHDI_INCLUDE=/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/include DAHDI_MODULES_EXTRA=" "…

Hi, Perhaps it is documented elsewhere but I could not find a direct solution after googling few minutes. My u-boot partition was stuck at the same version on the nightly. I needed to fix the reboot issue. I've tried few things like apt upgrade or direct dpkg -i... Anyway, this is what I did on a EMMC installation (/dev/mmcblk2) after I've built and download my own version of the package: dpkg -i ./linux-u-boot-dev-orangepi3_5.86_arm64.deb cd /usr/lib/linux-u-boot-dev-orangepi3_5.86_arm64 cat sunxi-spl.bin u-boot.itb > u-boot-sunxi-with-spl.bin dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2 bs=1024 seek=8 reboot I'm my case I had to u…

gcc-arm-linux-gnueabihf Unable to install？

I have Orange Pi PC plus. When I install Jessie Desktop it doesn't start desktop and only runs command prompt. Tell me how to start Desktop

Hi! Can I install a clean Armbian from within Armbian, without flashing a SD-Card? One idea: After installing Armbian, I used the NAND-SATA-install to copy my files to a harddrive. But on the SD-card there is still the old system. Can I switch back to boot the SD-system? Wittenborg

Hello i have orange pi one, so i would like to connect my ipcamera into orangepi eth0 port and it should be accessable to internet over wlan0 my settings like this eth0 has static ip address 192.168.2.20 ipcamera has static ip address 192.168.2.200 wlan get ip from my home network router (dhcp) 192.168.2.210 my home router ip is 192.168.2.1 normally orangepi has internet access when ethernet cable unplugged, when i plug the ethernet cable i can reach ipcamera interface on browser by typing 192.168.2.200 but internet gone. also i've checked - Use this connection only for resources on its network - section at the …

Hello, I am making a board coupled to a NanoPi Neo Core, and a RS485 converter to its UART2. The chip is a MAX1478 and I use the RTS (PA2). this is my armbianEnv verbosity=1 bootlogo=false disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=cpu-clock-1.2GHz-1.3v i2c0 i2c1 uart1 uart2 usbhost0 usbhost1 usbhost2 rootdev=UUID=a37457d6-57d2-4f17-a684-157b1a309a73 rootfstype=ext4 user_overlays=neo-core-stable-mac double-spi ds1307 param_uart2_rtscts=1 param_uart3_rtscts=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u if i run the command, cat /proc/tty/driver/serial |head -8 uart:16550A mmio:0x01C28800 irq:53 tx:120 rx:0 RTS|DT…

Hi everyone, I am experiencing a persistent boot issue with my Orange Pi Win Plus running Armbian, used as a headless server. The Problem: Whenever the board suffers a power loss (unplugged) or I issue a system reboot, it fails to start automatically. The power LED stays on, but the system/network never comes up. To get it to boot, I have to go through a frustrating manual routine: manually holding/pressing the power button, sometimes plugging/unplugging the HDMI cable, and repeating this process a couple of times before it finally kicks in. What I have already checked/ruled out: Power supply is NOT the issue: I have tested multiple different power ada…

Hello. My friend and I are comparing performance results with our cubietruck's. I'm using Armbian (Trusty vanilla latest update) and he's using ArmArchLinux. We tested a few dozen phoronix-test-suite tests and most results are the same except one. We both have a fresh OS install with no extras installed. The problem is with the phoronix-test-suite ramspeed integer copy test, I'm getting 812.03MB/s but he's getting 1479.73MB/s. Other ramspeed tests are giving proportionally equal results. What can explain such difference? Is my RAM running slower?

Hi, I am trying to create some kind of audio streaming server on orange pi zero. I've installed Qt5 and tried to start streaming audio using UDP datagrams. The problem is that sending one datagram takes a lot of time(~50-100ms) so there are interrupts in audio streaming. What is more I found out writing datagram gives me this message in dmesg: Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev- instead. I am using Xenial with Linux orangepizero 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l GNU/Linux That is my lsmod output: usbt…

Hi all, First of all sorry if i posted in the wrong directory I'm currently facing some issues with my orange pi one and in particular with node red and my dht22 temperature and humidity sensor i installed the stable buster version on my sd card this works perfectly and after that i installed node-red on it. in node red I installed the dht sensor pallet and added it to my flow but here is were the issues are starting, i need to select which pin it is connected to and what gpio i use. i can only select bcm gpio, rev1, rev2 or wiringpi 1 or 2 and then which pin it is connected to. i have the sensor connected t…

Hello, I am trying to run Armbian on my Orange Pi 3 LTS. The official Orange Pi image works normally: Orangepi3-lts_3.0.8_debian_bullseye_server_linux5.16.17 However, when I flash the Armbian image: Armbian 26.2.1 Minimal / IoT I get several boot errors during startup: [FAILED] Failed to start Apply Kernel Variables. [FAILED] Failed to start Dispatcher daemon for systemd-networkd. [FAILED] Failed to start Helper to synchronize boot up for ifupdown. [DEPEND] Dependency failed for Raise network interfaces. The system continues booting, but these errors appear every time. Hardware: Board: Orange Pi 3 LTS Image: Armbian 26.2.1 Minimal /…

Good day, I use prebuild Armbian Stretch mainline kernel 4.14.y. And I want to connect pcf8563 rtc through i2c protocol on TWI1_SCK/PB18, TWI1_SDA/PB19 hw A20 pins. pcf8563 slave address is 0x51. If by default, no i2c are enabled through overlays= in armbianEnv.txt, I still get i2c-1 device with addresses 0x51-0x57 occupied: root@lime2:~# ls /dev | grep i2c i2c-0 i2c-1 root@lime2:~# i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 30: -- -- -- -- UU -- -- -- -- -- -- -- -- -- -- -- root@lime2:~# i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 50: UU UU UU UU UU UU UU UU -- -- -- -- -- -- -- -- If I enable i2c1 through over…

Environment: (H2+) + linux-sunxi + ov5640 It can be registered by kernel ,but I can't capture any picture from camera . Here is my kernel demsg: ===================================================================================== # dmesg |grep VFE [ 1.720292] [VFE]cci probe start cci_sel = 0! [ 1.720328] [VFE]cci probe end cci_sel = 0! [ 1.720359] [VFE]cci_init end [ 1.720372] [VFE]Welcome to Video Front End driver [ 1.720514] [VFE_DEBUG]vfe_probe [ 1.720638] [VFE]pdev->id = 0 [ 1.720644] [VFE]dev->mipi_sel = 0 [ 1.720650] [VFE]dev->vip_sel = 0 [ 1.720655] [VFE]dev->isp_sel = 0 …

Hi, my Armbian Reports as 23.02.2 with Kernel 5.15.93. According to website there is already 23.5 with Kernel 6.x. How can I upgrade my existing installation? I tried apt update dist-upgrade and the "Update all packages and firmware" option in armbian-config. best regards thommy

i use oprange pi PC . i do ffmpeg -s 320x240 -f video4linux2 -i /dev/video0 /home/orange/out.mpg then i get video . i do arecord --device hw:0 -r 44100 -f S16_LE /home/orange/1.wav then i get sound . but i cannot get both at once . by using cheese , i have no sound . i guess alsamixer and i must do something , but i donot know the followings . aplay -L is null Discard all samples (playback) or generate zero samples (capture) sysdefault:CARD=audiocodec audiocodec, Default Audio Device dmix:CARD=audiocodec,DEV=0 audiocodec, Direct sample mixing device dsnoop:CARD=audiocodec,DEV=0 audiocodec, Direct sample snooping device h…

Hi. Is there any way to download armbian mainline kernel 4.11.6 source? (I want to compile small kernel module) There is only 4.9 source package available...

Hi all, I've connected a Serial-TTL converter to my Macbook Pro on one side, and an OrangePi Zero on the other, when I power up the Zero, I'm getting the following, what looks like an output with missing characters: I'm connecting with "sudo screen /dev/cu.usbserial 115200" and the adapter's driver in the network connections is set to 115200. The adapter is an Adafruit USB to TTL Serial Cable with a Prolific chipset. Any ideas?

After some months not using my OrangePi One, yesterday I installed Armbian 5.90 buster 4.19.57 (previously I had a stretch release). I did a clean install, downloading the image and burning the microSD with it. I noticed the button now works for 1st time since I bought the OrangePi One. It shuts down the device, no need to install or configure nothing. But, previous Armbian versions I had, were able to set the machine CPU speed at 1.2 and 1.1 GHz. Now (with Armbian 5.90) the maximum is 1 GHz. On previous releases, the file /sys/devices/system/cpu/cpufreq/policy0/scaling_available_frequencies contained: 240000 480000 648000 816000 912000 9…

On the 20.08.2 Buster release (Kernel 5.8.6) the headphone jack is not currently working. HDMI audio seems to be supported. aplay -L returns only the HDMI audio interface. (sun50i-a64-hdmi) but is not showing the headphone interface (should additionally show sun50i-a64-audio as in other working builds) This is also the case with the current development build (Armbian_20.11.0-trunk.32_Lime-a64_buster_current_5.9.7) A look at the device tree shows “<stdout>: Warning (unit_address_vs_reg): Node /sound/simple-audio-card,dai-link@0 has a unit name, but no reg property” on the first line of the DTS of sun50i-a64-olinuxino, sun50i-a64-olinuxino-e…

Hello, i want to compile an new Kernel for my BananaPi and used the great script from Igor. (Thanks for your support). Everything works perfect, but there are one error by the development of the Kernelmodul tusbd.ko. Do you know them? [ ok ] Installing external applications --2015-07-03 21:56:33-- http://www.incentivespro.com/usb-redirector-linux-arm-eabi.tar.gz Auflösen des Hostnamen »www.incentivespro.com (www.incentivespro.com)«... 74.52.236.44 Verbindungsaufbau zu www.incentivespro.com (www.incentivespro.com)|74.52.236.44|:80... verbunden. HTTP-Anforderung gesendet, warte auf Antwort... 200 OK Länge: 1851845 (1,8M) [application/x-gzip] In »»usb-redire…

Hello! I had a problem. I noticed for the third time in a week. After one day of standby (idle) is disabled WLAN. Not connected for SSH. It is unacceptable. How to fix it? ------------------------------------------------------------- BananaPi Pro (yellow/black) Vanilla Jessie.

So we get the Banana Pi M2+ killer soon it seems, just stumbled accross the 'NanoPi M1 Plus' in FriendlyARM repo: https://github.com/friendlyarm/h3_lichee/blob/master/tools/pack/chips/sun8iw7p1/configs/nanopi-h3/boards/sys_config_nanopi_m1_plus.fex According to fex file we get: H3 with primitive voltage regulation (1.1V/1.3V) and therefore 1200 MHz max eMMC AP6212 Wi-Fi/BT 40 pin header identical to M1 2 leds as usual (red/blue) Gigabit Ethernet 24 pin camera connector compatible to M1/Air 1 x USB OTG, 3 x host 2 x host (maybe the 3rd host port somewhere on headers) I would assume same board layout as NanoPi M1 now but one USB type A receptacle less and there the e…

Hi there, I am using Workstation edition on OPi PC+, system quite up to date. Problem: wired ethernet looks hardwired to DHCP (client) and I want to use static address(es). There is Network Monitor but I can't edit / delete "ifupdown(eth0)" connection. I can create another connection for wired eth in NM, static address, but it does not go active on system startup. I can switch off "eth0" and activate another connection from NM desktop, but I want system to start automatically with static IP (w/o user action).

Igor, Firstly, many thanks for some fantastic work.... I use your images for Audio streaming via USB. I have a cambridge Audio DAC sitting on the USB port and it works 99% flawlessly, even at 192k/24bit with only the occasional pop etc. I've noticed though that after a while, the "server" starts to have problems and the browsing of server stops working, with unused devices disappearing. A reboot is the only way to resolve. I've also noticed a possible memory leak and with a bit of googling, I see there's a problem with.. "Kernels versions 2.6.25 through 2.6.28.8 have a bug in USB EHCI controller driver that leads to large memory leaks with isochronous devices like …

Hello, I’ve just tried to boot the theoretically universal Armbian_5.72.1_Olinuxino-a20_Debian_stretch_next_4.19.17 image (taken from ftp://staging.olimex.com/Allwinner_Images/A20-OLinuXino/1.latest_mainline_images/stretch/images/) on my A20-SOM device, but with no success. The following output is displayed: **File not found /boot/dtb/ ** libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via “fdt addr ” command. Aborting! ** File not found /boot/dtb/overlay/sun7i-a20-fixup.scr ** … ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree SCRIPT FAILED: …

Greetings, can the NAS HAT for the Zero work on the Zero Plus2 H5? I have the Zero HAT, which connects to the Plus2 board, but when I connect a usb keyboard, it does not power it. Although a usb mouse lights up. I can't test the mouse fully because I'm using ubuntu server on the Plus2 which has no GUI. So again, is the problem that the Plus NAS HAT does not work on the Plus2? I see that there is a NAS HAT for the Plus2 with the same connectors that the Plus HAT has but it's smaller. Thanks in advance iomari

Hey Guys, i own a Lemaker Banana Pro device. The hardware itself is very fine, no issues with it, but the software support is pretty low. When i check internet, i see at least two images for it: Armbian Bionic - mainline based kernel 4.19.y Armbian Stretch- mainline based kernel 4.19.y I recognize that Armbian Stretch is based on Debian 9, which is the old Debian Version at all, so i am not willing to install it. But i wonder how it is with Bionic? Is Armbian Bionic based on Ubuntu Bionic Beaver? Is it that what i means? How long will the support run for this Bionic image? For me it doesnt matter if i install debian or ubuntu …

Hello everyone ! I'm facing a hard issue that I still cannot solve. On my Raspberry, on Raspberry Os, to be able to use Rustdesk (https://github.com/rustdesk/rustdesk, an open source Teamviewer ) I needed to add some tweaks to the /boot/config.txt file: hdmi_force_hotplug=1 (See doc) hdmi_group=2 (See doc) Now, I'm trying to replicate these behaviours on Armbian for Opi zero 3 (but it could probably work for all Allwinner cpus if a solution is found) When looking on the Armbian documentation for Sunxi, I've found this (See doc) : For example to always use the hdmi connector, even if no cable is inserted, using edid info when available and …

Hi, I have written a program with python e tkinter. The Gui automatically starts and runs well only I do access through remote desktop. How can I do that orangepi pc simulates the connection and starts my Gui? Sorry for my english, I hope I was clear enough. tx Ema

I recently updated the OS (apt-get dist-upgrade), for one of my test systems, and subsequent to this Kismet has stopped working with the wlan0 interface. Everything was working properly before this update. I see it (and wlan0mon) showing Promiscuous mode in the output of iwconfig. I'm not really a Linux person, so any pointers on how I can diagnose/repair?

hi there,the 4.19 kernel on win plus is great to play with but it really takes hours to boot. it stucks at starting kernel step. any advice?

Hello, I'm trying to read temperature from DHT22 on armbian using OrangePi's WiringPi library. The moment I call digitalWrite the whole system freezes. Previously I had raspbian and it used to work just fine. Am I missing something? Should I do some configuration maybe? Any help is appreciated. Thank you

Hi I'm auto-login using nodm with orange pi. I run my udp.py file by creating a file named udp.desktop under the .etc/xdg/autostart folder at startup. but I need to play the wav file using pygame in the .py file, but I get a warning that the audio device could not be initialized. If I trigger my .py file manually, I can play the wav file without any problems. probably unable to load sound drivers during autostart. Can you help with this.

The page for the Banana Pi image says: "Known bugs or limitations Latest 3.4.107 image have some stability issues. Build from sources or wait for update." I have some questions about this: - What kind of stability issues should I expect? I am seeing some network problems currently, however a lot of hardware in my network was replaced recently so I'm not sure if the banana pi is the source of these problems. The banana pi never locks up/show kernel oops/etc. - How would building from source help? I would expect to get the same image with the same problems. - When can I expect a new image to be available? Is it enough to download an old kernel from the archive? Or is t…

Hi Everyone. I have an Orange Pi One and I can use the micro USB (otg) port as a standard USB port - I can plug in a memory stick or USB speakers and it works fine. Is it possible to have the same functioniality with the OPI Zero? I tried and it does not work - I am powering the board through the GPIO header. Even if I plug in USB speakers that have an LED indication - no LED lights, so I guess no power. I looked at the fex file from the OPI One and could not see the difference there in the OPI Zero. I know it is in beta, so I do not expect it straight away, but it would be good to know if it is possible Thanks for any help. J

Hello together, I'm trying to activate composite output on my BananaPRO. First of all, I've added setenv command to my boot.cmd: setenv video-mode sunxi:1024x768-24@60,monitor=composite-pal,hpd=0,edid=0,overscan_x=32,overscan_y=20 then mkimage -C none -A arm -T script -d boot.cmd boot.scr copied boot.scr to sd-card and reboot. In u-boot I see: but my monitor (DELL 2007FP with composite input) and my TV (Panasonic Plasma) are still black. Any ideas? Thanks!

It seems the links to download the new Focal build for the nanopi neo core 2 are dead. https://www.armbian.com/nanopi-neo-core-2-lts/ Neither direct nor torrent seem to be working.

Hi, I've decided to make a fresh install on a bigger SD card using Armbian 22.05 Bullseye on my Opi PC+. The aplay command doesn't output any sound, and alsamixer show the card is H3 codec. I don't know if the sound is output to the HDMI port or any other problem. Anyone could help ? Than you

Hi, I am using orangepi+ with armbin debian jessie 5.20. I want to use softAp. orangepi+ have rtl8189etv, but when i am using Hostapd with isc-dhcp-server,if i enter to command line "iwlist wlan0 scan " , i can see kernel panic on screen. when i use bluetooth dongle (rtl8192cus), i can use hostapd and get scanlist.. rtl8189etv is not supported softAP?... or other problem? thanks...

DTS overlay to activate I2S DAC 5102a on Armbian Buster 5.4.43 armbian-add-overlay sun50i-h5-i2s0-out.dts If you don't have headers armbian-config (software->headers) Manual install whithout headers mkdir /boot/overlay-user/ dtc -I dts -O dtb sun50i-h5-i2s0-out-no-header.dts -o /boot/overlay-user/sun50i-h5-i2s0-out.dtbo add user_overlays=sun50i-h5-i2s0-out to /boot/armbianEnv.txt sun50i-h5-i2s0-out.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h5"; fragment@0 { target-path = "/"; __overlay__ { pcm5102a: pcm5102a { #sound-dai-cells = < 0x00 >; compatible = "ti,pcm5102a"; status = "okay"…

The program nand-sata-installer doesn't work to put the image on the onboard storage with all 4.X kernels (orange pi plus wifi/nand). When i use the older kernel it works fine without any issue. Also when i compile this image by myself it doesn't work either Is there a way to put the SD image to the local storage and how can i do this with this 4.x kernel?

I am running Ubuntu Xenial (legacy version) on my Orangepi zero 256 Mb version and using it as a web server with light torrenting. The SoC temperature reading in armbianmonitor reaches above 80 C easily. When i log in via ssh after boot the temperature reads usually 60-65 C and normal operations easily cross 70 C. This is my first SBC so I am not sure if this is normal? Can anyone tell me if these temperature readings are fine and should I do something about it?

I compared two boards （opi zero h3 and opi zero plus h5) and found that cpu pins for 26 gpio are the same . so I modify the code in wiringPi about cpu detection to force return true value . and it works. the step: 1. git clone https://github.com/xpertsavenue/WiringOP-Zero 2. modify the code in WiringOP-Zero/wiringPi/wiringPi.c (or using the attached file to replace）。 3. make && make install 4. run "gpio readall " to test 5. run "gpio write 30 1" (the red-led on, wiringpi pin 30 control red-led status). wiringPi.c

Hello I'm quite new with armbian and Banana Pi, but have some experience with Raspberry PI. I started with Banana PI M2 Zero and armbian because of current unavailibility of Raspberry PI which is needed for some of my DIY pinball projects https://lisy.dev/ With a 5.15.48 Kernel Image I noted that the internal ethernet of M2 Zero is set to disabled, where with a 5.10.60 Kernel from the archive it works. After some investigation I used the "sun8i-h2-plus-bananapi-m2-zero.dtb" overlay from the 5.10 Kernel with a 5.15.43 Kernel and was happy that eth0 was working again. However as I think it is not advisable to mixing Kernel version…

Hello everyone, I’m looking for an old Armbian image: Armbian 5.73 stable for NanoPi NEO Air, specifically the one based on Debian 10 (Buster) with the 4.19.20-sunxi kernel. Unfortunately, it’s no longer available in the Armbian archives. If anyone still has a copy of this image (e.g., Armbian_5.73_NanoPiNeoAir_Debian_buster_next_4.19.20.img.xz), I would be very grateful if you could share it or point me to a working download link. Thanks in advance for your help!

Hi, I'm testing the new Rev.K board and facing troubles with uplink performance. Downlink is ok. I already asked on Olymex forum but no response so far. $ iperf3 -c 192.168.0.110 Connecting to host 192.168.0.110, port 5201 [ 4] local 192.168.0.104 port 45700 connected to 192.168.0.110 port 5201 [ ID] Interval Transfer Bandwidth Retr Cwnd [ 4] 0.00-1.00 sec 3.59 MBytes 30.1 Mbits/sec 708 4.24 KBytes [ 4] 1.00-2.00 sec 4.14 MBytes 34.8 Mbits/sec 964 2.83 KBytes [ 4] 2.00-3.00 sec 4.19 MBytes 35.1 Mbits/sec 956 2.83 KBytes [ 4] 3.00-4.00 sec 4.16 MBytes 34.9 Mbits/sec 944 2…

Hi everyone, I want to create an USB device, for this i am following this tutorial : gadgetfs. It works fine, but when i want to have an endpoint superior to 4, i cannot. I just changed to Unfortunately, in the folder created i have only this files : ep1in ep1out ep2in ep2out ep3in ep3out ep4in ep4out musb-hdrc I thought a usb device can have 32 endpoints. So, is it possible to have an extra endpoint ? And i have an extra question, as a kernel noob, I don't fully understand how this guy came out with thi…

Does anyone use an infrared remote control with the Lirc / rc6 / mce program..and have a verified configuration? I can't configure the above to work on Orange pi 3 lts But I want the Lirc program and not the ir-keytable 🙂

While analog audio output (through the GPIO connector) works out of the box using the legacy kernel 3.4.113-sun7i, I could not get it to work with the stable kernel 4.9.12-sunxi. Since the driver is not activated in the stable kernel, I added the following to the dts: &codec { status = "okay"; }; This lead to the following `dmesg` output: sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok `aplay -l` gives: **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 However when I play back some audio file, no sound is genera…

Thanks for your effort on this project. Much appreciated. I was able to follow this tutorial (10 minutes, 24 seconds in) on the Debian image to get the TV out working. I'm building scripts to modify the networking between a number of modes - super helpful to get a console access when I break something and lose all networking access. Is there support for this on the Ubuntu side? The simple "add 'tv' to the bottom of "/etc/modules" doesn't do anything. Please advise. Thanks!

I'm trying to use armbian on orange pi one, and it does not start. Previously I used the armbian, however I needed to format the card, now I am putting the same version of armbian 5.25 server and desktop does not work, I tried version 5.35 and tbm does not start, the non-image card does not light any led. However, when using both debian xfce and ubuntu xfce for orange pi one of orangepi.org, the board called displayed video and is working.

I am getting significant graphical issues with most programs on the "Jammy Gnome desktop" version. I also saw similar issues under KDE desktop after clicking a button relating to OpenGL in the graphics settings (and couldn't figure out how to get that dialog back or undo the setting). I would prefer to stick with Gnome, I assume this issue has something to do with hardware/graphics acceleration having an issue, the application launcher seems to be immune from the issue. Sorry, I am quite a noob when it comes to Linux/programming related stuff, I couldn't find any other mentions about similar issues in this forum. The issue happens on both this 5" LCD and an HDMI TV at 4k.

Hello, I have a problem on my orange pi 3 lts. Namely, I have armbian 23.03 Jammy Xfce installed and on some screens it shows normally, on others the image does not appear. I also tried using the Uart converter and it loads everything normally, but then the following message starts appearing every second. [ 161.905394] panfrost 1800000.gpu: js fault, js=0, status=INSTR_INVALID_PC, head=0xa005bc0, tail=0xa005bc0

Hi folks! I'm a proud owner of 120 Orange Pis. Now I want to do git deployment and reboot the device. I've enabled the ttyS3 for serial connection. Now I want to reboot the device. Sadly enough the device shuts down when executing a reboot or "sudo init 6"command. And when I type shutdown, the device is still on. I've search all kinds of forums, but I cannot find a suitable fix for this. Thanks in advance!

Hi I'm going use the terminal armbian and send AT commands to the gsm SIM800L, but I am uable to write these commands. I used screen and minicom like this : screen /dev/ttyS0 115200 & minicom -b 115200 -o -D /dev/ttyAMA0 I use to connect to ttyS3 but nothing happen i think the uart3 or pins 8 and 10 is not working or not enable of course i have ttyS3 in ls /dev list but not working. I've connected according to the following guidelines: i use : orange pi plus 2 board armbian for orange pi plus 2 SIM800L v2.0 image of my connection and board :

TL;DR: The small H2+/H3 boards unlike their bigger siblings are all prone to overheating due to smaller PCB size (on the larger boards the PCB's groundplane acts somewhat as a large heatsink dissipating heat away from the SoC). Due to mainline kernel settings not being optimized currently all these boards are slower under constant load compared to legacy kernel. This should change but won't unless someone is looking into it and spends some time on this. Two areas that deal with this overheating tendency or are somewhat related are thermal protection / throttling: use the thermal sensor(s) inside the SoC to downclock various engines if specific tre…

Hi, how you decode video on Nanopi Duo with hardware acceleration? Have you any images or instruction how i could test hardware acceleration by using Nanopi duo? Mainline kernel doesn't support hardware acselleration, right? I tried build image with legacy kernal (3.4.x), but it doesn't run. Any ideas?

Hello everybody! I upgraded my armbian on my Bananapi M1 to... armbian 20.08.17 Buster with Linux 5.8.16-sunxi Unfortunately I don't have any internet access anymore now. I can still SSH into the board, but I can not ping any server with it. What more information do you need to help? Thank you very much for your attention!

hi guys, i'm using NanoPi neo core using a battery and a volt booster. and I want to control the voltage booster to turn off all peripherals to conserve power and prevent battery drainage. I figured there's a PWR-LED pin connected to GPIOL10, which turns off when the system shut down. is there a way to map another GPIO in the same way so i could know when the system has shut down - so it will be safe to cut power off? thank you so much.

Pink screen on monitor Acer AL1716. Armbian 5.35 legacy OrangePi PC HDMI with DSUB convertor new installation In previous version 5.24 works monitor fine. If I connect OPI to second monitor LG1752S and restart OPI, screen is OK. After reconnect back to AL1716, screen is still ok. But after restart with AL1716 is screen again pink. Tested some different resolutions with h3disp, but still get pink screen. Looks like problem with monitor detection at start. Is possible to disable detection after start with working monitor and set as default? Any other solution? Edit: I found…

Hi forum members, the apt utility in my bpi m2 zero can't find neither dnsutil nor bind9-dnsutil for bullseye, here the output: pi@fewo-relais:~$ sudo apt install bind9-dnsutils Paketlisten werden gelesen… Fehler! E: Encountered a section with no Package: header E: Problem with MergeList /var/lib/apt/lists/deb.debian.org_debian_dists_bullseye_main_binary-armhf_Packages E: Die Paketliste oder die Statusdatei konnte nicht eingelesen oder geöffnet werden. pi@fewo-relais:~$ pi@fewo-relais:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=bananapim2zero BOARD_NAME="Banana Pi M2 Zero" BOARDFAMILY=sun8i BUILD_REPOSITORY_URL=h…

Bpi M2 Zero Armbian 23.02.0 sid can't change volume alsamixer said: This sound device does not have any controls. How can I fix this issue ?

I have an OrangePI h3, I upload the Armbian in the SD card, but independent if the SD card is in or not, the Orange pi always display the both network leds turned on. Therefore I do not know if my problem is related to the SO or any hardware problem.

Env is ARMBIAN 5.31 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i When I run Kismet on this system (which creates a new interface in Monitor mode - wlan0mon), the original WiFi interface loses any connections, and will no longer function properly. Is this a expected behavior? Is there any way to get both monitor and normal mode to co-exist? I've looked around and don't see any obvious driver updates that would address this. Any suggestions (beyond adding a second WiFi adapter)?

I have a 320x240 ili9341 based lcd. Based on the instructions on this forum I hooked it up to my orangepi pc (latest desktop) , loaded the fb kernel driver and run some tests. MPlayer (sudo SDL_VIDEODRIVER=fbcon SDL_FBDEV=/dev/fb8 mplayer -vo sdl -framedrop test.mpg) runs fine. The display shows the video without any problems. Also some python scripts work fine (clock etc..) But anything else fails.... con2fbmap 1 8 does nothing Using FRAMBUFFER=/dev/fb8 startx (or any other program) just starts everything in the main display (hdmi). I need to be able to run any program I want on the spi lcd. Am I missin…

Hello, when I shutdown or reboot my cubietruck nothing happens. Just the green LED flashes 2 times, pause, flashes 2 times again, pause, and so on. Here is the link to my System diagnostic information: http://ix.io/1bcg Best regards

I want to drive 2 SPI devices on my orangepi zero. I enabled `spi-spidev` and `spi-add-cs1` overlays and set `param_spidev_spi_bus` to 1. But by I still get only `/dev/spi1.0` available. When I add `param_spidev_spi_cs=1`, I get `/dev/spi1.1` but `/dev/spi1.0` disappears. Do I see it correctly that I can choose *either* `/dev/spi1.0` *or* `/dev/spi1.1` but not both with that overlay? How can I activate both cs pins? There are a bunch of example custom files out there, but none are meant specifically for the setup where I need spi1 (instead of spi0) and need to use a GPIO pin for cs1. And I can't really find any docs on how to write my own overlay. So any help is appr…

Hello, I have problem that wireless interface only reachable when ethernet cable plugged to my orange pi zero. I use nmtui, to setup my WiFi connection. All connects fine and works. But when I disconnect ethernet cable, I lost also WiFi connection. I see this post: https://forum.armbian.com/topic/4098-orange-pi-zero-wifi-issues-when-disconnect-ethernet-cable/ But even after rebooting without ethernet cable, WiFi connnection doesn't work. Then in a new clean image, I try to run nmtui without connecting ethernet cable. WiFi connects without any errors, but doesn't work. Please, help! Spoiler This is my ifconfig -a, when …

Hi there, I tried your images for orange pi, but doesnt work on orange pi mini 2. I tried ALL the images on the factory site, but somehow they placed copies of images for other models. (debian images are the same) Only image so far worked: lubuntu, but when i login, ssh session is killed. (as well root/orangepi as orangepi/orangepi) its driving me nuts to get this working. Any ideas? Great work btw!

Hello, Im trying to get 2 Uarts working on an Orange Pi Zero+2. Im using armbian Buster image for OPiZ+2 Linux orangepizeroplus2-h3 5.4.43-sunxi #20.05.2 SMP Mon Jun 1 18:26:22 CEST 2020 armv7l GNU/Linux I added UART1, UART2 and UART3 to armbianEnv.txt and was able to read / write on ttyS2 on pins 8 (PA00) and 10 (PA01). But couldnt find which pins ttyS1 or ttyS3 are on. I read at that UART 3 should be Tx PA13 Pin 24 Rx PA14 Pin 23 Is anyone able to suggest which pins I can use for a 2nd UART and is there a file I can look in to find the configuration for the UART Overlays ? Thanks Chris …

Hi, I have installed Wheesy 3.4.108 on my Banana Pro. connected to it using SSH from xterm on my linux box, did various housekeeping, set up user squeeze Installed logitech media server works OK Installled Squeezelite ---- needed to set up alsa, ran sudo alsamixer, Alsamixer ran OK but when I hit Fkeys on host machine to select various alsa menus, alsamixer terminates and drops back to Banana pro CLI, obviosly F key keybindings are not what alsamixer expects. Fails under both xterm and putty and on two linux host systems. What do I do to make banana pro use the Function keys F1-F6 to work as alsa requires? I note that there are lots of…

Hi all, on orange pi zero plus with allwinner H5 I have problem to install python library pyA20 to controll gpio. On H2 it was easy to do this. Same suggestions? Thanks in advance

hi guys i have little problem i connect my orange pi zero directly to relay but not work the realy is HUI KE hk19f-dc 5v-sh in yellow box , but if i attach 3v and gnd of gpio work o_O anyone can help me?? thankz

Hello My system is installed on the internal eMMC. After a system update my OPi will not boot anymore. Perhaps anyone can help. Thx.. Gesendet von meinem WAS-LX1A mit Tapatalk

Hello, I am using OrangePi Zero v1.1 board with 512MB DRAM and 8GB Class4 microSD card. I am trying to flash Ubuntu 18.04 LTS downloaded from Armbian site .. Everything goes well till the login point and then suddenly nothing moves. PS - USB adapter 5V, 1.6 Amp rating FTDI converter std. connected to UART of the board. Heatsink mounted on top of the IC. Please Help resolve the possible issue. Thanks !! Rajat Below is the boot up process as captured. U-Boot SPL 2019.04-armbian (Nov 18 2019 - 23:36:05 +0100) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2019.04-armbian…

Hi, I had until yesterday an Armbian version from a year ago on the board, until then I never had problems with my network (WiFi). Yesterday I had then made an apt update + upgrate. After that, however, I suddenly had the problem that some access points are no longer found. This is so that my access point (Fritzbox), my mobile hotspot from smartphone (Samsung) and a network of a neighbor is no longer found. Other access points are still found, so there are still WiFi access points available but I can no longer find mine. Now I have installed the latest version today and still the same problem. Manual entry unfortunately brings nothing because the connecti…

I was able to write to a Samsung sd card the image for my orange Pi lite. The overscan is bad on my TV but I got past initial setup. Once it boots to the desktop there is no response from the mouse and I thought the keyboard. No keyboard shortcuts work. But I was able to drop to terminal and type. What could be going on? I've tried different cards, keyboards, and mice. Edit: I've tried different power supplies too!

Help me. Armbian view my USB-HID joy in /deb/bus/usb/xxx/xxx, and my device not work in emulator(nes, sega and etc.) I think that my joystick mast be /dev/input/jsx. I find information, that module "joydev" direct the joystick, but "lsmod" show, that "joydev" is not run. Modules "joydev.ko" and "hiddev" is absent in filesystem.

Hello, I recently installed Armbian 5.85 legacy on my new Orange Pi Lite in order to try out my new Orange Pi camera, but it's not being recognized at all, even after following the instructions in this topic: I already tried doing the following (as root) unsuccessfully (no errors returned, but still can't detect camera): sunxi-pio -m "PG11<1><0><1><1>" #DOVDD sunxi-pio -m "PE15<1><0><1><0>" #Power_Down sunxi-pio -m "PE14<1><0><1><1>" #reset modprobe gc2035 modprobe vfe_v4l2 Here's the output of lsusb: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001…

Hi, I've just wrote today's latest image for my Orange Pi PC: Armbian_21.02.1_Orangepipc_focal_current_5.10.12_desktop At first boot, I am asked to make my user and everything is fine and I end up in the XFCE desktop. All works fine. Then, I reboot the system. I see it booting and when X is starting, the screen goes blank (all black). If I do Ctrl+Alt+F1, I can log in in text mode, but X shows nothing. Thank you for your hard work on Armbian! -Alexandre

HI.. I have an opi zero and I want to copy the card and use it in a NanoPi Neo I plugged it in and it works but displays Orange Pi Zero on the login screen. What steps should I take to make it work best in the NanoPi Neo? Thanks. V.

I've installed Armbian_5.14_Orangepiplus_Debian_jessie_3.4.112_desktop on a ORANGE PI PLUS 2 H3 QUAD CORE 1,6Gz / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) _ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | |_| |_ | |_| | | | (_| | | | | (_| | __/ | __/| |_ _| \___/|_| \__,_|_| |_|\__, |\___| |_| |_| |_| |___/ Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i System load: 0.52 Up time: 1 min Memory usage: 14 % of 2013Mb CPU temp: 59°C Usage of /: 19% of 15G then installed lightdm and running the xfce4 desktop with HDMI monitor of 1920x1080 I can't…

i have Downloaded the Image for the Orange PI PC H3. the Image flashed over the MAC with DD are only this screen. Then i think ok i testing windows have testet win 10 with Rufus and win 7 with Suse flasher with is in the Package. Are all the same. how its the Problem?

I'm using g_ether to connect OrangePiPc+ to network over USB OTG. On legacy kernel, that was giving 140 Mbits/sec IN (download from network to OrangePiPc+) and 170 Mbits/sec OUT. After upgrading to mainline kernel 4.19.62 (or 5.3.9), IN throughput degraded to 93-98 Mbits/sec (while OUT improved reaching up to 210 Mbits/sec in CDC EEM mode). This easily reproducible on both my boards OrangePiPc+ and OrangePiZero with latest Bionic images (clean installations + "modprobe g_ether iProduct="Linux-USB Ethernet/RNDIS Gadget" iManufacturer="Netchip Technology, Inc." dev_addr=02:81:05:F0:5C:24 host_addr=02:81:05:F0:5C:23 use_eem=0" ). Any ideas where is the bottleneck…

Hi , I just move my banana pi pro which was running bananian up to now to buster minimal. I'm using it as domoticz server. It requires few usb port to have all my gateway working. So I need to make USB OTG running in HOST mode. I did lot of testing, read many thread, but quite stuck right now. Here is what I have already done : First I have activated in DTB usb@1c13000 , and change mode to host. I have also activated usb0-vbus. I added also regulator-boot-on in usb0-bus. and last test I did is adding usb0_vbus-supply = < 0xb1 >; in phy@1c13400. For those who may need later on, here is the command I did: …

Hi, I am using Nanopi Neo board and I need RS485 driver to control DE pin automatically. I have prepared DTS Overlay file: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&uart1>; __overlay__ { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&uart1_pins &uart1_de_pin>; rs485-rts-gpios = <&gpio6 8 0>; /* PG8 active-low */ linux,rs485-enabled-at-boot-time; rs485-rts-delay = <0 300>; }; }; fragment@1 { tar…

hi all, I use cubietruck Linux 3.4.104-sunxi I would like to understand partition ramlog-tmpfs on /var/log type tmpfs (rw,relatime,size=524288k) in fstab is not present. I have the problem that it is always full, more than 90% My cubietruck it is install on nand, I would like to mount the partition of sd, how can I do? regards

Hi, Does anyone has image for Orange Pi Zero 2+ H3 Ubuntu Dekstop Kernel > 4.x? Thanks.

Hello everyone, I've got an orange pi pite 2, I install in my sd card armbian, it start but when I login and create a new account and reboot, I see termianl and not the desktop of armbian, If i reboot it ask me again to login, but I can'f see the terminal.... PLEASE HELP....... THANKS

Hi, After upgrading linux-image-current-sunxi64 package from 21.08.1 to 22.02.1, bringing kernel version 5.15.25, the CPU temperature raised abnormaly on my olimex teres board. Temperature is above 60°C at startup, whithout any activity or load average. The issue persists with latest 5.16.16 kernel from linux-image-edge-sunxi64 package. I noticed temp at startup around 30°C with 5.4.88-sunxi64 kernel, 40°C with 5.10.60-sunxi64 kernel and above 60°C with 5.15+ kernels. Does anyone have cpu temp issue with 5.15+ kernels ?

Good evening. I am preparing an Orange PI Plus 2 in order to be the first computer for my 8 years old son. The idea is that he could learn Scratch by watching some video tutorials in YouTube The problem is that actually, if you pause a video, and the you want for it to restart, only video does it. Sound doesn't starts again.It remains muted. Then, if you click to watch another video, sound come back. But you loose it again if this second video is also paused. It's a bit annoying. Do you have the same issue ? Best regard. Maesstrissimo.

Hi! My Banana pi Pro with Armbian v5.20 does not boot since i issued a 'init 1' command. While booting, it show only that; Starting kernel ... Uncompressing Linux... done, booting the kernel. How to activate the boot debug mode. I tried many keyboard keys without success. Thank you!

Hi everybody, I have an OPZ board (256 mb). I couldn't manage to start work wifi in automatic mode. I tried manual configuration then tried nmtui in both cases wifi starts only after Ethernet plug was connected. OS: ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i How can I solve this problem? Thanks!