Allwinner sunxi

Help I'm trying to get my t230 dvb stick to work with my orange pi pc2 I copied the .fw files across and reboot but it will not load the firmware can anyone help please

Hi all Need's help, my devoces orange pi plus 2 and distibtion os armbian server, me need hardware acceleration on plexmediaserver, i used more ways, did not help.

It seems I have to install either of them for my chromecast to play nice. I have no prior experience with neither of them nor do I know which one is better. There are various threads on the internet but would be interested which one the community uses / trusts, cause I am a bit hesitant on adding random repos. My use case: Stream mkv on local with subs or transcode if it can't show subs. Board: Orange Pi Pc OS: Debian Stretch on 4.14.18 Would appreciate any feedback even if it's only a link to your preferred software / guide.

I have problem whit armbian i have orange pi pc plus and is load but last loaded informacion is cpu heat, memory capaciti... What i must press ? Pls help

Hello My system is installed on the internal eMMC. After a system update my OPi will not boot anymore. Perhaps anyone can help. Thx.. Gesendet von meinem WAS-LX1A mit Tapatalk

I need to make custom intro on my bigtreetech cb1 when i try plymouth some time give me error and sometimes the system startup normally as normal Plymouth without pics only 3dots in middle of screen i want examples or guidelines to make it and when i make update to initremfs files it’s give me error such as error to create hard link what I should i do

Hi! Is PMP support build-in in newer armbian images? I installed ARMBIAN Debian GNU/Linux 8 (jessie) 4.4.3-sunxi on my banana pi. Or is a recompile still needed? With the default image i can see a dmesg "error ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP". If recompile is needed can someone please post a link where to find step-by-step instructions how to recompile armbian with PMP support? Is the guide on htpcguides.com still correct? Thank you

Hello all, I used using opi one with (Armbian_5.90_Ubuntu_bionic_4.19.57) image. and used the uart0 pins for hardware pwm but the output was around 330mv pwm not 3.3v as i want. my initial thoughts was either the uart0 isn't disabled or there are no pull ups activated, although i tryed using this: https://github.com/iboguslavsky/pwm-sunxi-opi0 Remap pins in FEX: ; Disable debug UART0 [uart_para] uart_debug_port = 0 uart_debug_tx = port:PA04<2><1> uart_debug_rx = port:PA05<2><1> ; Enable PWM0 on PA05 [pwm0_para] pwm_used = 1 pwm_positive = port:PA05<3><0> bu…

Hey folks, I'm trying to play back a couple test files, H.264, 720p. These play without dropping frames on the stock Android ROM for a little while but then freeze, seemingly on certain keyframes? It's always in the same place. Anyway, I tried playing them with mpv on Armbian 5.38 desktop install and it drops frames like crazy. I know the stock Android ROM can play back Youtube content (in the app) without dropping frames - it seems like this should be doable based on what I understand about the capabilities of the A20 and on hardware support in the legacy kernel in the Armbian image ... is there tuning I should be doing? Or options for mpv that I can try? I've used VLC f…

Hello, I am using a NanoPi Duo2 with Armbian 22.11 and Kernel 5,15,80. This device uses an AP6216 wireless interface, which I have noticed are pretty common on sunxi based boards. I ran some bandwidth tests and had pretty poor results: [ ID] Interval Transfer Bandwidth [ 3] 0.0000-1.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 1.0000-2.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 2.0000-3.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 3.0000-4.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 4.0000-5.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 5.0000-6.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 6.0000-7.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 7…

I have spent hours trying to get any activity on my new Orange Pi PC I just purchased. I have been downloading and burning different images, reformatting / trying different SD cards, 2 power supplies, using DD, WIn32DiskImager, Rufus, scanning my SD using F3, etc lots of "pain". The solution - which I found somewhere halfway by accident - is that some boards do not have card slots mounted correctly, but you can flex the card to make it work. So yes, I flexed the SD card and applied power, and like magic I got actual LED activity. OMG it boots now! Would have worked the entire time but it did not make contact with the SD card. My solution for now is to stick a laye…

Hello. How I can to set the 480x800 resolution? I have LCD display with portrait orientation and no one display mode from h3disp does not fit. On boot display is working fine, but after booting everything is bad. Booting video: After booting:

Hi, I seem to have "fried" the default Debug TTL UART (the 3 pins next to the hdmi connector). (connecting the ground of the usb-ttl to TX of the UART and leaving it there for a few minutes is not a good idea it seems :-)). The orangepipc+ still works when booting from emmc (armbian 5.17 debian jessie, kernel 4.7.3) but does not seem to want to boot from microsd (tried console only 5.17/4.7.3, 5.21/4.8.1). So I would like to debug that but whatever usb-ttl I connect I don't see anything (tried 3 different usb-ttl to make sure it was not the usb-ttl device)> My question: is it possible to see uboot messages (or at least the kernel boot) via a different port…

Hi guys, I bought the orange zero and then I realized how poor wifi. I had some wifi modules from old tablets at home, they are rlt8188eu. After I joined the orange, there was another problem. Wifi driver could not be initialized, because I knew that these modules can operate on orange pc out of box, I began to research the problem. Cause I am linux ZERO, it took me longer time, but I finally found soulution. Problem was in fex file for orange zero, wifi_usbc_type = it´s without parameter, after I added some parameter ( "5" from working orange pc fex), wifi work like a charm. I´m not sure if it´s purpose, or bug, so I write you....

I was testing the orangepi PC+ armbian build 5.20 (Armbian_5.20_Orangepipcplus_Debian_jessie_3.4.112_desktop) when messing with it it seemed to have random reboots. I thought initially it was because it was lacking a heatsink or fan. So I added both and the issue persisted. Thinking maybe if I flashed to emmc it might resolve the issue it froze in emmc install and is effectively softbricked from what I can tell sadly. I also tested a second OPIPC+ but was unable to get it to boot. I tested with multiple new power cables as well.

Hey Guys, IM finally trying to make use of my OPi0 and Im planning on creating a daughterboard/hat/shield similar to the expansion board they sell, but with only the bits i need. One thing i'm wondering is if its possible to feed the power (5v) via the pins on the expansion board and not using the OTG input. Im trying to keep it as clean as possible and dont want to have the OTG connection for power. Is the regulator only on the OTG? Last I checked, my power supply gives out a steady 5.3v feed @5amps (driving some power hungry pixels). In regards to sound. I wanted to use an LMA386 amp on my custom daughter board to boost the output for a 4 ohm speaker i'…

I'm using an Orange pi zero H2 and currently have the pi configured as an access point. I want to be able to SSH into pi using access point wifi, then switch pi onto my home wifi network. When I use the "nmtui" utility I no longer see any available wifi networks. Is it possible to see available wifi networks when I am using the pi as an access point? Thanks, orangepi noob

Hi, Orange PI Lite Armbian 5.25 (latest download available at the time of this post) ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i I would like to have the Pi boot without the desktop environment, and either start it manually over SSH. I found a tutorial that said to edit /etc/default/grub and change GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" to GRUB_CMDLINE_LINUX_DEFAULT="text" but that file does not apply, so I'm not sure how to impliment this for armbian. I don't want to remove the desktop environment completely, but rather have it bootup to command line only, and if I need the desktop environment log into via SSH and either re-edit "a file" and…

I've been trying out the latest version (4.3) of armbian on my Banana Pro and I noticed that the power button does no work as expected (apparently pressing it results in a hard reset). It looks like the OS can see the power button but I can't find a way to receive the button pressed event, the OS always halts first. Did anyone find a way to get the power and reset buttons to work?

Hello! There is a common issue with my Orange Pi PC +. I didn't find any solution for it. When I "shutdown -t 0" my device, it continues to consume power and the chipset is warm. Is it possible to turn the power off completely through the command line? Thanks in advance!

After figuring out how to enable analog audio on the Lime2 (https://forum.armbian.com/index.php?/topic/4224-analog-audio-on-lime2-with-stable-kernel-version-49/), I now have the problem that there is a clearly noticeable mainline hum whenever no sound is playing. The hum goes away as soon as any sound is playing on the device, and it returns a couple seconds after the sound stopped. It appears like some kind of power saving feature kicks in. With the legacy kernel the hum goes away during boot and does not return. Any ideas?

Hi specialists, I'm trying to understand how the axp209 on Banana Pi works with the A20. In the Banana Pi schematics I see, that they are connected with only four lines. Two lines are used for I²C (TWSI), one is from axp209 PWROK to RESET# of A20 and another one is connected from axp209 IRQ and GPIO2 to NMI# of A20. When system is off and I press my Power Button (K1) on the Pi, the system is booting. System is running and I long press the Power Button, System shuts down. But can anyone say whats happening? What does axp209 do with IRQ, GPIO2 and PWROK pins? Wich way does the A20 recognize, that it has to shutdown? Yours Martin

Hello! Brand new user here to the NanoPi Neo and even the forum. I'm planning to use a NanoPi Neo as hardware "interactor", the main idea is to connect a NanoPi Neo to a smartphone (Android or iOS), power the board from the USB cable and work in Host Mode to interact with de smartphone with libimobiledevice or adb. OTG does not support charging + data at the same time without a "special" OTG adapter. What I want to do is power the NanoPi by using the smartphone and even interact with it in host mode, like a regular computer will do, in simple terms, using a single cable, but getting power from it. Is this possible using NanoPi microUSB+OT…

Hello! I use cubieaboard2, setup "trusty_3.4.110_desktop", on first boot the cubieboard2 itself off. Power Off after the kernel load labels. Debian_jessie_4.4.1 work fine. Why may power off spontaneously?

Hi all, i need a little help. On a CB2 powered from vbus and with a lipo battery i cannot shutdown in any way. When i issue poweroff command it reboots instad of shutting down. Tried also shutdown -h now. Any suggestion?

I have read through the forum that Banana Pi Pro does not support directly powering drive over USB as it might be too much for this board. In my setup I use 2 A power adapter for my Banana Pi and an active HUB with power supply of 1 A, but with limit of 500 mA for HDD. Still, when connecting HUB to Banana Pi and HDD to HUB the same issue appears as when no HUB is used - the red diode turns off and Banana Pi looses power. I have already tried several HDDs (500 GB, 320 GB, 2 TB) - all with the same result. Anyone has some idea why this might be occuring despite powering drives from external source? Does Armbian have any software limitations that are creating this issue? …

Hello, I have been looking for days without finding an answer, so here goes. I want to know if there is a way of turning on the banana pi, without using the onboard switch. Because the Banana pi r1 doesn't power on automatically when powered by the battery connector. And i don't want to solder wires on the pwr button, but i would also like to avoid using the usb connections because of the lower power throughput. Thank you in advance for the information.

Hi, I did read a lot about temperature and power consumption on this forum. Most is about bad parameters for the Orange Pi H3 boards. I use armbian 5.25 stable with 3.4.113-sun7i kernel. On both i run this same version, the only difference is that i use an other script.bin on the orangepi. The script.bin who is in the distrubution. I dont use a heatsink on both. I noticed the following On the Orange Pi: Load1 is max 0.50 with 2 values of 1.00, avg 0.20-0.25 Load15 is between 0.08 and 0.14 The temperature is between 49 degrees and 52 degrees Celcius The PMU current is between 400 and 800 mA PMU Consu…

OK

Good morning all. I was trying to power up my nanopi M1 through the VDD_5V and GND pins shown in GPIO.jpg image and/or the power pins on the debug GPIO pins, the schematics of the board power electronics are attached too on page 7 and 8, may by I'm wrong but what I see on those schematics is that all the power switchs and DC/DC converters can be powered through those pins but when I do that using a USB cable cutted on the micro USB side and prepared with the right terminals to fit the pins -with a 5V USB charger- then the tension drops aproximatelly to 4.60-4.67 DCV, the board starts by lighting dimly the power LED (as normally) but when the power LED lights strongly also…

Hi, I understand that powering the Orange Pi Zero through the USB OTG interface is convenient but suboptimal due to low power, especially if you have other devices attached to the board. I've seen recommendations that powering the board directly via the 5V and GND on the GPIO from a clean and sufficiently powerful power supply is preferable. I know in theory what needs to be done but I don't know how to physically connect to the board. The GPIO is a 2x13 row of conductive holes in the board. (Is there a name for this sort of thing, by the way?) Say I have two wires, 5V and GND. How do I physically attach a wire to one a hole? Do I need to …

After a (sudo) poweroff, the ethernet port leds turn off, the usb sockets' power supply too, but the green led remains on. I would like the green led to turn off after a sudo poweroff. How can I do that? What's the best way to do it? It's an Orange Pi PC with ARMBIAN 5.60 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i Thanks.

Hello Forum, please excuse my bad English. I try setting up a stratum1-server. Based on GPS. For this I use the Banana Pi with kernel 4.6.2 and the Adafruit GPS. The GPS is connected to GPIO J12 and works. RX/TX is not the problem. The problem is the right pin for the PPS-signal. dmesg|grep pps* [ 0.001207] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.067281] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 [ 3.260009] pps_core: LinuxPPS API ver. 1 registered [ 3.260018] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>…

I made this simple dts file for my GPS NTP server running on Zero2/3 and Zero2w On Zero2, use PC9 as PPS in , and on Zero2W use PI5 . It should be configured in /boot/armbianEnv.txt, but I unsuccess on zero2w, so you must comment out two lines and compile it by yourself. Maybe help someone. sun50i-h616-pps-gpio.dtso

Hi! I didn't find much info in the forum on how to correctly apply RT patch to the Armbian (Orange Pi Zero Plus H5 board). Here is how I did: Built Armbian as follows: 1) I downloaded patch-5.4.22-rt13.patch from https://mirrors.edge.kernel.org/pub/linux/kernel/projects/rt/5.4/ and placed into ~/build/userpatches/kernel/sunxi-current ( I saw from the logs that this is the folder for the builder to search for user patches in my case) 2) Started ./compile.sh --> FULL OS image for flashing --> Show a kernel configuration menu before compilation --> orangepizeroplus (H5) as target board --> current (recommended , which is 5.4.23…

Hi! I've coded a script that allows me to create a bootable disk of my favorite systems for different boards. it does a dd of the mbr (446 kb), then with fdisk and mkfs create the partitions, and at the end copy all the data for the root partition and others. This works for raspberry pi2 pi3, but for the orange pi it works only if the sd card is the same of the one used to backup the system, so i've investigated if the fstab or boot.cmd has some uuid of the disk but everywhere i found the device name instead of the uuid identifier. I don't understand why the orange pi lite don't boot with a different sd card if it have the same mbr and the same partitions. app…

Hi, I'm using a xenial system with Kernel 4.9.11-sunxi on LIME2 (actually it's an Olimex A20-SOM with external RTL8211 PHY) and trying to prevent the ethernet from coming up on boot. When turning the system on, the ethernet interface will assign a random MAC address; later on my script sets a proper MAC from an assigned range. Until then the eth0 interface must stay down to prevent the network from being spammed with bogous messages. This is because the ethernet interface chooses a random MAC address when the system boots up; later on a script sets the proper MAC address from an assigned range (along with IP and route configuration); The link must stay down un…

Can someone post the printenv for a NEO PLUS2 because i think i f*** up my device and doesn't boot from SD or USB .... the only i get is the boot menu. Or any ideas to help me to fix this ?

Hello! I have Orange Pi Zero 3 I got Armbian image from this link - https://github.com/armbian/community/releases/download/24.5.0-trunk.474/Armbian_community_24.5.0-trunk.474_Orangepizero3_bookworm_current_6.6.28_minimal.img.xz Of course I've made apt update and apt upgrade And now I'm tying to install zigbee2mqtt using this guide - https://www.zigbee2mqtt.io/guide/installation/01_linux.html So, I can't list USB devices root@orangepizero3:~# ls -l /dev/ttyACM0 ls: cannot access '/dev/ttyACM0': No such file or directory root@orangepizero3:~# ls -l /dev/serial/by-id ls: cannot access '/dev/serial/by-id': No such file or directory I have …

Hello I have a problem with my Xunlong Orange Pi PC Plus, if I put an SD card with Armbian_20.11.3_Orangepipcplus_buster_current_5.9.14 or focal (format with Etcher) it will boot with the MMC is not with the SD card i have an error Trying to boot from MMC1 ... MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment ... mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr ... EHCI failed to shut down host controller. Loading Ramdisk to 4969c000, end 49fff9c3 ... OK Loading Device Tree to 4962b000, end 4969bfff ... OK Starting kernel ... and after…

Hello, im new to linux and armbian systems, but im really interested in the topic, recently im working with an a20-Olinuxino-Lime2 , and my goal was to put another OS, for that i followed some tutorials to install a Linux Mate system on the sd card, i configured it to access the internet thought my router but after a point that i changed the kernel , i lost connection to the internet, all my "interfaces" files are the same and i can ping to my router, but i cant ping from my computer to it booting up it gives some errors opening lib modules: systemd-udev(439) could not open builtin file : "/lib/modules/3.4.109-sunxi/modules.builtin.bin" modprob : ERROR: ../lib…

Goodmorning, I've upgraded my Orange Pi-PC to 5.11 Upgrading process OK then rebooted. Now PI continue rebooting (leds turn on as usual but after a while they turn off) and i'm not able to access it. Have you any advice? is there a way to reset it? thanks in advance

Hello. I have a annoying problem each time i burn with 'dd' a armbian*raw image (custom) in linux my orange pi lite not boot, i must format and write in windows (write32...) then works. any idea? [ 998.313215] usb 3-7: new high-speed USB device number 6 using xhci_hcd [ 998.443018] usb 3-7: New USB device found, idVendor=058f, idProduct=6331 [ 998.443026] usb 3-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 998.443030] usb 3-7: Product: Mass Storage Device [ 998.443033] usb 3-7: Manufacturer: Generic [ 998.443036] usb 3-7: SerialNumber: 058F091111B [ 998.443733] usb-storage 3-7:1.0: USB Mass Storage device detected [ 998.446321] scsi host…

Hi, in the last weeks I'been trying to use the serial ports 5 and 6 (tty5, tty6) of the cubieboard2 using DTB but still not working. First of all, I must said that i'm not a linux expert, only a linux user with some experience and all the information below is the result of multiple weeks of internet research. for the moment i'm able to get the cubieboard2 to recognize the ports, and using a c++ program I write on all serial ports, i get a response from tty0 but can't get the gio pins of the serial ports 5 and 6 to work. here is what I have done so far: first, I downloaded the device tree compiler sudo apt-get install device-tree-compiler then, nav…

Hi, can anybody please help me with device tree overlays to enable serial uarts? Maybe I'm missing a step or I'm doing it wrong? UART3 and UART4 are not working on Cubieboard2 and Cubietruck running the latest mainline armbian image. I've added the dto by following command: echo overlays=uart3 uart4 >> /boot/armbianEnv.txt dmesg shows they are enabled: root@cubieboard2:~# dmesg | grep tty [ 0.000000] Kernel command line: root=UUID=871ffecf-ac1f-4168-bca0-f4ba6a2d8f33 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ub…

hi guys i have an orange pi one and download "Armbian_5.20_Orangepione_Debian_jessie_3.4.112" and "Armbian_5.20_Orangepione_Debian_jessie_3.4.112_desktop" for this , after write image with "Win32DiskImager" or "Etcher" , use this for orangepi and this is good. but after i want connect this to computer and get a backup , windows dont detect this drive and come error "you need to format the disk in drive. . . " i test this with all of usb port in computer and use some sd ram for this but dont work...

Hello, I get an error when i try to use the PH5 pin as digital output. PH5 is the number 229 according to the following equation: (8-1)*32+5 = 229 echo 229 > /sys/class/gpio/export -bash: echo: write error: Device or resource busy If i use other pins like PH13, PH19, PH20 or PH21, all work correctly. For example, for PH13 as digital output: echo 237 > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio237/direction echo "1" > /sys/class/gpio/gpio237/value echo "0" > /sys/class/gpio/gpio237/value echo 237 > /sys/class/gpio/unexport I get the same error in the Cubieboard2 …

Hello guys ! 1) New SD card 16 Gb 2) Install on it armbian 5_14 desktop 3) Install apache 2 reboot ---> OK 4) install mysql server and client reboot ---> OK 5) install php5 reboot ---> OK 6) install phpmyadmin reboot ---> OK 7) install java8 reboot ---> OK 8) install netbeans 8.1 + plugins reboot ---> OK 9) install other programs and services reboot ---> OK 10) install igorpecovnik/hostapd reboot ---> Problem as I told in other post This happens three times today , to be sure before write that. So pratically this is the price to pay if I want an access point ? :( What I have to do ? …

Hello to all! I have banana pi m2+ with Allwinner H3. OS: ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i I program linux kernel driver. And I am can't run R_UART. I write to register any value, and read value alway zero. It seems that APB0 bus is not cloked. Or device R_UART reset asserted. What I do wrong? Sincerely, Dmitriy.

Hi to All, Today I try to re-build Armbian (with legacy kernel 3.4 and Debian Jessie) customized by me a week ago and get into trouble to buld and boot it. I am fixing also: BOOTBRANCH=v2015.10 REVISION="5.05" At build process I see that kernel was migrated from version 3.4.110 to 3.4.111 but it builds with no problems. Unfortunately, USB redirector build did not succeed displaying bunch of errors: [ o.k. ] Installing external applications [ USB redirector ] In file included from /data/armbian-legacy/sources/usb-redirector-linux-arm-eabi/files/modules/src/tusbd/usbd.h:67:0, from /data/armbian-legacy/sources/usb-redirector-linux-arm-eabi/files/mo…

Hello everybody! There is a big problem with the Banana PI Pro. The system is installed on the micro SD, when updating the packages I get the following result: root@bananapipro:~# apt-get install mdadm Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: libc6-dev : Depends: libc6 (= 2.19-18+deb8u9) but 2.19-18+deb8u7 is to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). root@bananapipro:~# apt-get -f install Reading package lists... Done Building dependency tree …

Hi, I found a similar thread about space problem on /boot when upgrading the kernel, but it was with debian jessie, not Ubuntu, and the proposed "trick" doesn't seem to work anymore: This is what I get: Actually, I am facing this problem since I set up my system a year ago, but didn't take the time to solve it. But now, I would like to finish the aimed set up of the device (home server) and would like to get this out of the way. Thanks for any suggestion.

I'm trying to use a few of the GPIO pins as output pins on an Orange Pi PC+ running Armbian 5.26 and legacy kernel 3.4.113-sun8i. When I look at the FEX file, it appears that the GPIO pins have all been disable d by default: [gpio_para] gpio_used = 0 gpio_num = 0 I don't recall them being disabled by default in previous versions of Armbian. I s this a recent change? Anyway, I edited the file and changed it to: [gpio_para] gpio_used = 1 gpio_num = 3 gpio_pin_1 = port:PA13<1><default><default><default> gpio_pin_2 = port:PA14<1><default><default><defau…

I got a banana pi plus like the one this web page https://www.armbian.com/banana-pi-plus/ and downloaded legacy jessie server on it. After applied the last step on the page： sed -i '1isetenv fdtfile sun7i-a20-bananapi-m1-plus.dtb' /boot/boot.cmd mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr ln -fs bin/bananapim1plus.bin /boot/script.bin reboot the board just can't boot up. anyone have same problem?

Hello, Recently I found that audio stopped working on my Banana. Last time (3 months ago) I was using shairport to stream audio over LAN and all was working just fine. Now I see that somehow information about audio card was removed: root@bananapi:~# alsamixer cannot open mixer: No such file or directory root@bananapi:~# cat /etc/asound.conf cat: /etc/asound.conf: No such file or directory I already try apt-get update && apt-get upgrade && apt-get dist-upgrade. My system information: root@bananapi:~# uname -a Linux bananapi 4.9.12-sunxi #4 SMP Thu Feb 23 19:46:51 CET 2017 armv7l GNU/Linux root@bananapi:~# lsmod Module …

I am lost, the soundcard used to work when I first started with this board but now I get a "aplay: device_list:270: no soundcards found..." error. When I tried to enable the analog codec using armbian-config I get an empty screen. This also used to work the first time. So I created a new SD card using Armbian Stretch this time but with exactly the same result. I am desperate! The diagnostic output is here http://ix.io/1x25 Kind regards, Hans C

For a long time, for more than three years, I did not use my BananapiPro board. And recently I decided to launch it again.I downloaded new Armbian image distribution. But the system when loading gives out an error. After the initialization of the devices, a message appears: Device 0: unknown device ethernet@1c50000 Waiting for PHY auto negotiation to complete......... done Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.2.200 (5ms) *** Warning: no boot file name: using 'COA802c8.img' Using ethernet@1c50000 device TFTP from server 192.168.2.1; our IP address is 192.169.2.200 Filename 'COA802C8.img'. Load address: 0x42000000 Loading: T T T …

cant build dahdi on armbian 5.2 how it make on arm? /usr/src/dahdi-linux-complete-2.11.1+2.11.1# make all make -C linux all make[1]: Entering directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux' make -C drivers/dahdi/firmware firmware-loaders make[2]: Entering directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi/firmware' make[2]: Leaving directory '/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi/firmware' make -C /lib/modules/3.4.112-sun8i/build SUBDIRS=/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/drivers/dahdi DAHDI_INCLUDE=/usr/src/dahdi-linux-complete-2.11.1+2.11.1/linux/include DAHDI_MODULES_EXTRA=" "…

I am using legacy Armbian_5.14_Orangepi2_Ubuntu_xenial_3.4.112.7z and a Logitech C110 and I cannot set some params. However I can set this in my PC under x86_64 3.13.0-91-generic. Below is the output of v4l2-ctl in orangepi2. Any idea? $ v4l2-ctl -l --verbose VIDIOC_QUERYCAP: ok error 22 getting ctrl Brightness error 22 getting ctrl Contrast error 22 getting ctrl Saturation error 22 getting ctrl Hue error 22 getting ctrl White Balance Temperature, Auto error 22 getting ctrl Gamma error 22 getting ctrl Power Line Frequency error 22 getting ctrl White Balance Temperature error 22 getting ctrl Sharpness error 22 getting ctrl Backlight Compensation …

Hi, I'm using fbtft with legacy kernel in orange pi zero to be able to use 3.5 inch raspberry LCD with ILI9486 (not sure). Everything works and I can get image from the LCD (although it is terribly slow). But I have one big problem. LCD freezes after some time or when screen screen changes or even sometimes during initialization . Is there anything wrong with the spi driver in armbian ? How can I get over this issue ? I'm sure there is nothing wrong with the lcd because I have tested same lcd on raspberry pi and I have about 500 of these lcds for a project. This is the my fbtft options : modprobe fbtft_device custom name=fb_ili9486 gpios=dc:18,reset:2 busnu…

Hi to All! Currently i am using 3.4.107-cubietruck #14 SMP PREEMPT Wed Apr 29 11:57:42 CEST 2015 armv7l GNU/Linux including a WLAN USB Adapter AWUS036AC from ALFA. First question: Does anybody got this adapter to work with a cubietruck as a WLAN-AP? Second question: If yes, what driver did you use for the successful implementation? Third: How to disable the onboard WLAN? I want to use it as a 5GHZ (AC-standard) WLAN-AP! Many thanks in advance. Regards, Ireng

Installed Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop. After a while, namely the clock after 5 work OrangePi Plus 2 disappears from the internal network. Do not pass the ping, connection to the SSH. But you can connect from the outside through the routed ports of the router to the SSH. Pings from it pass only to the router (192.168.0.1). Prior to other devices in the local network, pings also do not reach. This is when the internal network disappeared. Before its disappearance with pings and connections on the SSH, there are no problems. What could be the problem? armbianmonitor -u - http://ix.io/17Ni

Hi people, I have a problem after restarting my cubieboard, I had an installation in nand (older install with old files) and now I can not get it started. It is possible to mount that nand or repair it to restart ... Thank you

Hi all and thanks for the great work done. I'm trying to install armbian on the eMMC of my NanoPi M1 Plus, the system boot from SD and I create the user then I start the nand-sata-install command. In the "choose an option" I have only "1 Boot from eMMC - system on eMMC" and then I choose ext4. The process complete and I launch the "dd if=/dev/zero of=/dev/mmcblk0 bs=1024 seek=8 count=1" command directly after. The system does not boot anymore with and without the SD inserted. On serial console, in both cases, I get: U-Boot SPL 2017.05-armbian (Jun 13 2017 - 15:14:45) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl…

Hi Igor, while trying to reproduce/fixing my boot problem, I stumbled across some weird things regarding your new update script. I've put a complete new image on sd-card only (Armbian_4.5_Cubietruck_Ubuntu_trusty_4.2.3) which works fine, boots and reboots. Then I've tried to use your update script which I called via: wget -q -O - http://upgrade.armbian.com | bash with the letter O and a blank between the minus and http, is this correct? First strange thing I noticed is, that it starts but doesn't run through completely. It ends with this output: Don't think that this should be the normal behaviour!? And remember that this wasn't the case when I tried…

Hello. I have the following problem with my Orange Pi PC: When I turn it on, only the green and orange LEDs of the ethernet port are flashing. There is no output on the HDMI port. I have already tried different microSD cards and different images. It used to work perfectly, but all of a sudden it stopped working. Maybe an issue with the power supply (it is the offical power supply 5V 3A DC jack).

device: orange pi pc soft: Armbian_5.14_Orangepipc_Debian_jessie_3.4.112.7z my log via serial: U-Boot SPL 2016.05-armbian (Jun 05 2016 - 09:45:23) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 05 2016 - 09:45:23 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scanning bus 0 fo…

1.Only OpenGL ES2.1 and 1.x work: chenyifei@orangepi3:~$ glxinfo|grep OpenGL OpenGL vendor string: Panfrost OpenGL renderer string: Mali T720 (Panfrost) OpenGL version string: 2.1 Mesa 20.2.0-devel OpenGL shading language version string: 1.20 OpenGL extensions: OpenGL ES profile version string: OpenGL ES 2.0 Mesa 20.2.0-devel OpenGL ES profile shading language version string: OpenGL ES GLSL ES 1.0.16 2.glx did't work with panfrost dri: chenyifei@orangepi3:~$ cat /var/log/Xorg.0.log|grep GL [ 10447.384] (II) Initializing extension GLX [ 10447.384] (EE) AIGLX error: sun4i-drm does not export required DRI extension [ 10447.395] (II) IGLX: Load…

root@orangepipcplus:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 1002 0 0 eth0 0.0.0.0 192.168.30.1 0.0.0.0 UG 1024 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.30.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

Hello everybody! I'm trying to make a carPC based on Armbian (5.25 Bananapi Ubuntu xenial default 3.4.113 desktop) and a banana pi, almost everything works except for sound in navigation. root@bananapi:~/7ways# ./7ways root@bananapi:~/7ways# ALSA lib pulse.c:243:(pulse_connect) PulseAudio: Unable to connect: Connection refused root@bananapi:~/7ways# ALSA lib pulse.c:243:(pulse_connect) PulseAudio: Unable to connect: Connection refused root@bananapi:~/7ways# ALSA lib pcm_dmix.c:968:(snd_pcm_dmix_open) The dmix plugin supports only playback stream root@bananapi:~/7ways# ALSA lib pcm_dsnoop.c:545:(snd_pcm_dsnoop_open) The dsnoop plugin supports only capture stream root@b…

Source for kernel in package : linux-source-4.19.38-next-sunxi is for 64BIT architecture , is not possible to get source for 32bit architecture

Hi all, first of all, I'm new to this forum even if I've been using Armbian on my Olimex Lime2 since lot of time and I find it a great project; thanks and keep up the good work! Now: I would like to use the Lime2 SPI #2 on pins "b" in master mode to communicate with a single slave device. What I did was: 1) downloaded Armbian v5.31 (latest available release at the time I write) 2) following the guide at https://docs.armbian.com/User-Guide_Allwinner_overlays/ I modified /boot/armbianEnv.txt to contain: verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=8cf9ed72-8225-4db8-a3a2-a242d648d…

Hi, I use armbian distribution on opi+2e , in order to operate the Jeedom home automation system. I occasionally encounter crashes of my opi, which becomes inaccessible in SSH. We are several users of this system to encounter the same problems. In logs, date is 1970, so we suspect a time synchronization problem. We use timedatectl for ntp synchronization, but it appears that rtc clock (fake clock) is not stable. Why? Any solution to keep rtc clock synchronous with ntp? Somes members of Jeedom community try with hardware RTC clock on I2C, and it seems working. But any existing other solutions? Thanks.

I have Orange PI Zero running the stable Ubuntu image. Kernel: Linux orangepizero 3.4.113-sun8i. I'm writing a python3 app to communicate with an Arduino using UART. The app works fine for a few hours and then it stops being able to send or receive commands to/from the Arduino. Is there some known issue with the UART on OPI Zero? It looks like the file descriptor for the serial port becomes unavailable somehow.

Hello I'm using my Banana pi Pro as a domitic box with a Zwave Key connected on USB (aeotec Gen5) This morning, unfortunately, I made a apt-get Upgrade which updated the following packages armbian-firmware armbian-tools-jessie base-files bash ca-certificates dbus dbus-x11 e2fslibs e2fsprogs file fonts-opensymbol libc-bin libc-dev-bin libc6 libc6-dev libcairo-gobject2 libcairo2 libcomerr2 libdbus-1-3 libdbus-1-dev libgnutls-deb0-28 libgnutls-openssl27 libgudev-1.0-0 libhogweed2 libmagic1 libnettle4 libpam-modules libpam-modules-bin libpam-runtime libpam-systemd libpam0g libpng12-0 libpng12-dev libreoffice-base-core libreoffice-common lib…

Hi all I have a banana pi running armbian. After the update to kernel 4.8.4 I am experiencing problems in enumerating USB device during boot (meaning device connected before powerup) I get errors like: [ 6.572517] usb 4-1: not running at top speed; connect to a high speed hub [ 6.578537] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.578547] usb 4-1: can't read configurations, error -61 [ 6.789488] usb 4-1: new full-speed USB device number 4 using ohci-platform [ 6.848598] usb 4-1: not running at top speed; connect to a high speed hub [ 6.853598] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.853620] usb 4-1:…

Hello, I've problem use i2c features on newest CTDebian3.8 Jessie os. Exactly i using CT3 with DVK570 extended board witch deploy any signals from CN8 and CN9 slots. I can't see any i2c devices though that i see two buses after used i2cdetect -l: root@ctdev:~# i2cdetect -l i2c-0 i2c sunxi-i2c.0 I2C adapter i2c-1 i2c sunxi-hdmi-i2c I2C adapter root@ctdev:~# i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- UU -- -- -- -- --…

ARMBIAN 5.38 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i Shows: Bus 004 Device 002: ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter But ifconfig -a show only eth0 adapter. No ra0 link I've tried sudo apt-add-repository ppa:thopiekar/mt7601 sudo apt-get update sudo apt-get install mt7601-sta-dkms But still no results.

Hi i cant connect my orange pi pc plus via wifi. I have install armbian 5.20 and then "sudo apt-get update" and "sudo apt-get upgrade" I try to configure with nmtui, but i cant or dont know how to do Can anyone help me with a tutorial please?? Thanks a lot

Hi, I just got a NanoPi Neo Plus2 for which I must prepare an image for our software. Basically I must have a working Ethernet-over-USB, Wifi and NIC. I started with your current Debian image compiled with uses Armbian v8.75 and Linux kernel v4.19.20. In this image Wifi works, but loading the g_ether module does not seem to work. I assume I need to patch the kernel to make this happen, which means I need to build my own images. So I created a Virtualbox environment as described in the documentation, and compiled an image with all the defaults (apart from a date-tag I add to the kernel name for identification). I installed the image to the eMMC and b…

I am using orange pi pc plus after using armbian system, there is an infinite network with WLAN0 and WLAN1, but at present there is no law to use both networks at the same time and connect different SSIDs. Error: Connection activation failed: (7) Secrets were required, but not provided. pi@orangepipcplus:~$ cat /etc/os-release PRETTY_NAME="Armbian 24.5.0-trunk.512 jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.4 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy ID=ubuntu ID_LIKE=debian HOME_URL="https://www.armbian.com" SUPPORT_URL="https://forum.armbian.com" BUG_REPORT_URL="https://www.armbian.com/bugs" PRIVACY_POLICY_URL="https://www.armbian.co…

Hello I tried to install xrdp in opi one,but it doesn't work.

Edit: --------------------------------------------------------------- OrangePi PC+ ARMBIAN Buster and Focal v20.05.x Problem: I can't get UBoot to rotate the screen. Solution: I still don't know. --------------------------------------------------------------- Hi. I am using a Tablet Display with a controller (link) as a monitor, the case is that the controller is vertical (1536x2048) and I want to use the monitor in landscape mode (more normal). The ARMbian system of my OrangePi PC + single terminal without desktop starts rotated (vertical). Once started from the command line I can write: echo 3 | sudo tee /sys/class/graphics/fbcon/rotate_all …

hi! I'm running vanilla cli-version of armbian v4-2 on my olimex lime2. However, decided to run it from a sata-attached hdd to improve speed and durability. the procedure i used is descibed here (and got a lot of help from the creator of the website, thanks!): http://papermint-designs.com/dmo-blog/blog.php?id=3, but i will shortly sum up what i did. flashed the sd with armbian cli image 4-2 let it reboot for it to use the whole card created a 10gb partition for rootfs and swap on the sata drive changed fstab to mount the rootfs on the sata (removed everything but defaults and noatime because system booted in ro-mode otherwise while running from hdd) : #/dev/…

Hello! I have problems with Banana Pi and for today - updated all packages, and I can't connect via SSH nor FTP to my Pi. I have not changed anything, but there is automatic script which dist-upgrades the whole system, it is running once a day. Till 12.34pm CET everything was working fine - from logs, even I think till past 4pm I have connected via SSH to Pi, but then after kernel upgrade (seen note after logon) and reboot I can't access Pi in any way. I've tried to see logs: connect SD card to laptop with Linux to check if there is any problem, but didn't found nothing special. I've also tried to attach HDMI monitor but no signal. Seem…

Hi there, I have upgraded from Jessie to Stretch, apt-get update apt-get upgrade change repo name in apt config files update, upgrade. Now I lost some functionality: - X does not start, nor automatic nor manual, message "no screens found" - Firefox crashes even before main window open, no error message (remote X). In armbian-config I tried to install desktop, but command returns quite fast (much faster than on fresh Stretch). It seems no distribution problem, because I have installed Stretch on another card and there everything works fine. (except extreme slow screen update on remote X). What to c…

First of all I have to mention, that my knowledge of linux is very small. I started with raspberry about two years ago and switched to cubietruck. First I didn't use Igor's image, because I wanted to have a graphical front end. After getting used to putty and ftp I swithed to Igor's image - it was very convenient, small and fast. So I also bought a banana, when Igor published an image for it, and a cubox i Pro. All of those images worked out-of-the-box - it was a pleasure to work with it, especially for a noob. In the meanwhile I switched to RasPi2 for a while, but yesterday I wanted to start again with the other ones. So I downloaded the latest images. But big s…

Hello Community, I am trying to install Docker on my Cubietruck. As a guide i used the official guide by Docker https://docs.docker.com/install/linux/docker-ce/ubuntu/#upgrade-docker-ce When I am at actual installation step I walking in this following error msg. Does anyone have a idea where to start looking ? Thx.blub474

Hi, I can't seem to mount any drives with journaled user/group quota. I just get this error: root@bananapipro:~# mount -o rw,defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0 UUID=56790abd-531d-43b7-8cf8-9bfc85105f6a /media/56790abd-531d-43b7-8cf8-9bfc85105f6a mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so. If I run the mount command without the quota stuff the drive mounts without any problems and is browseable.

I have set up a server on a nanopi-r2s running Armbian version 5.15.25-rockchip64. It all works fine apart from one thing: while other devices can successfully use BIND on the server, the server itself cannot find the local BIND. If I type in this command host device.localdomain 127.0.0.1 it returns the following: device.localdomain has address 192.168.0.20 192.168.0.20 is the correct address for device.localdomain from the local BIND. If I omit the 127.0.0.1 from the command, it does not find the correct address.: device.localdomain has address 36.86.63.182 device.localdomain has address 36.86.63.182 Host device.localdomain not …

Hi, I have problems with the versions "Armbian 5.25 Orangepizero Debian jessie default" and 5.26. When i install Nginx, the directory "nginx" is created in /var/log/. After a "reboot" the directory is then "disappeared", not possible to start Nginx. I can create the folder with error.log and access.log and restart Nginx. After this, it runs. After a reboot again, nginx is missig again... Any hints? The same happens with 5.25 and 5.26 on OrangePiOne, so far tested... I thing i'm not the only one with this problem. (I testet with "root" permissions only)

Hello Everybody, Iḿ using a Cubietruck (Cubieboard3) I ve tried to install the Jessie Server and the Xenial Server with the vanilla Kernel. Both effords failed. The bootprocess from SD Card starts, but it dosen t come to an end. The following things happen: In the beginning there is a short warning regarding mmc. After that the bootprocess starts, but then the message "Running /script/local-block..done" appers many times. Then there is another error message and the process starts from the beginning. Details in the picture. I don t think that the SD Card or the Cubieboard is the problem, because the Jessie Server with the legacy kernel and the old cubian are…

hi all, I've been running into an issue where the kernel starts throwing error messages (https://pastebin.com/bmPJPeq0), the board becomes very slow and the cpu load goes to 11 and stays there. This seems to happen when I change the CPU freq using armbian-config to anything lower than 528MHz. Any ideas how I could resolve this?

Dears, I have done the last update. I lost dkms, and when trying to recompile/reinstall it, I started get strange errors. It seems binaries in linux-headers are compiled for Intel. I would even the kernel is configure for Intel. Was not able to compile the module actually. Was there some mishap? Rui

I should have known better..... today i did an apt update and saw thet there was an update to 5.38. Installed it and like with nearly every last update the device (OrangePi +) didn't boot. Did you even test updates in the stable repo before ? Don't know whats going wrong, so i will test it, but thats annoying.....

Hi, I have serious problems with the 5.25 images of armbian on a cubietruck. After a fresh install and apt-get update apt-get upgrade I get errors with : dpkg: error processing archive /var/cache/apt/archives/linux-libc-dev_4.4.0-78.99_armhf.deb (--unpack) This is for the Armbian_5.25_Cubietruck_Ubuntu_xenial_next_4.9.7 image, with other images this concerns a different package. Only Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113 works. After this error, the filesystem seems to be defect and is remounted ro. On another try, I removed the rmount ro on error option from the fstab and the /var/lib/dpkg directory was corrupted. …

I am experiencing serious problems with booting Armbian on OrangePi Lite. I flashed SD card with a fresh image of Armbian_5.20_Orangepilite_Debian_jessie_3.4.112_desktop.img At the first boot it always freezes right after this line: Started WPA supplicant. It stays there forever and I have no choice but power off the system. At each subsequent boot the system freezes very frequently but at different lines so again I need to reset it. However sometimes it succeeds at the second boot and I am able to login as root and then create new user and enter the desktop after that. I was very happy that it finally started and everything was working fine (inc…

Hello, I've got some problems with a Cubietruck. First thing to state is that the com-port apparently has died. It was connected via a USB-converter 3,3v and worked flawlessly for a long time. I replaced it with a new one but no go. In the beginning no problem, I could use SSH. Second thing is that the hard disk became erroneous. I bought a bigger model but no boot. I thought that the UUID-entry in /etc/fstab caused this and changed it via tune2fs to the old one, but still no boot. Thus I could no longer use SSH! And I cannot mount the old harddisk, it's to erroneous! Third thing is that I tried with a new image, and the cubie seems to fina…

Hi, we bought several Lime2 and tested them. Unfortunatelly, the GBit-Lan did not seem to work reliyable. Later ping tests revealed a packet loss on many boards of 1% to 20%. (eg. "ping -s 9000 -i 0.0001 -c 5000 fritz.box"). Some boards dont have any problems, other more. On heavy access with SSD it's increasing a little. It's happens also without SSD. Other boards worked fine at the same power and network cable. Its possible thant this strange TX_DELAY isn't set correctly? Are there other problems known? I used the wheezy image with kernel 3.4.105-lime2 and 3.4.107 from you latest wheezy image. The image with Kernal 4.0.4 stopped after "restarting sshd",…

Hello, I'm using the Wheezy Image with Kernel 3.4.107-cubietruck, downloaded 25th May 2015, on my Cubietruck. Working through the Guide "Enable Access point mode" I ended up having a running hostapd with a ESSID which my clients can see but can not connect. I tried with default config given by the image (ssid=cubietruck and wpa=2 with wpa_passphrase=12345678). I also tried disabling wpa (wpa=0). But no client can connect. Starting "hostapd /etc/hostapd.conf" prints root@cubietruck:~# hostapd /etc/hostapd.conf Configuration file: /etc/hostapd.conf nl80211: Could not re-add multicast membership for vendor events: -2 (No such file or directory) Using inte…