Allwinner sunxi

1. hardware: orange pi zero /H2+ 512Mb 2. armbianmonitor -m got a negative temperature number。 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 17:34:31: 240MHz 0.10 1% 1% 0% 0% 0% 0% -16°C 0/7 17:34:36: 240MHz 0.09 1% 1% 0% 0% 0% 0% -16°C 0/7 17:34:41: 240MHz 0.09 1% 1% 0% 0% 0% 0% -16°C 0/7 3. uname -a Linux opizero 3.4.113-sun8i #4 SMP PREEMPT Wed Nov 22 13:45:28 CET 2017 armv7l GNU/Linux 4. using image Armbian_5.35_Orangepizero_Debian_jessie_default_3.4.113.7z

Hi guys, I have the bad idea to build up little by little some house automation with an opi1 that I don't use. Just for fun. So I'd like to start with armbian and build everything from there, with no precompiled images. The first thing I want to try is Google assistant. Can I use the assistant sdk that I can find on official website? Or there is something better for opi? Can I eventually integrate it with something like Hass.io or similar? I'm open for any advice. Thank you in advance

I am trying to install Tensorflow on my Orange Pi One. Everything seems okay on install, but pip says ERROR: Could not find a version that satisfies the requirement tensorflow ERROR: No matching distribution found for tensorflow My guess is that the OS is a 32bit version and that Tensorflow runs on 64bit ones only. However, I can't find any source of checking whether the Armbian version I have is 32bit or 64bit.

Igor please help me Tried again to run with 4.1.6. Cubietruck is needed online. He thought for a moment, then got all che need for dhcp and gave the console. Only one problem... can't lift the access point, ifconfig sees wlan0, iwlist sees wlan0, but hostapd does not work there is no BCMDHD module, (not running modprobe bcmdhd) what to do? Igor please help. root@gate:~# modprobe bcmdhd modprobe: FATAL: Module bcmdhd not found. How to translate the adapter in Ap mode? where to get the module? there are modules b43, brcm80211, rt2x00, rtlwifi but they are not suitable. in the distribution which was used before - it worked thanks in advance!!!

Hello, dear users and developers. Could you help me to enable SPI1 subsystem and use the corresponding device file /dev/spi... to test/probe SPI communications on my Orange Pi Win (Plus) machine? For the sake of that I am ready go migrate from currently good for me and quite fresh "raspbian for orange pi" where I've already implemented about 95% of required functionality. And it seems the only place where I can talk to people about SPI stuff in ready linux distributions is right here. I actually read here about some SPI issues on Orange Pi Zero but I have some troubles at getting possible packages to experiment at my current distribution and I am not skilled,at all, at …

I am a new owner of Nanopi K1 plus. Can someone tell me how to install a desktop version of my device?

Hi! I've tried to compile the lwjgl lib on my opiplus2, but I'm stuck on ant compile_native_es. ant jars_es finished successfully. The error: [apply] /usr/bin/ld: cannot find -lEGL Tried to install libegl1-mesa-dev package but it conflicts with the mali driver package. Is it possible to compile the lwjgl with opengl-es on the opi, or that's a dead idea? Thanks in advance!

hello everybody, I am new on the linux world but after some search and work , I managed to start my Orange Pi plus 2E with a stretch image armbian 5.38 and everything is working well. Recently after successfully installed several domotic solution like Jeedom and Zwave, I start to work on the integration of a 3G card, but I need to use some CLI to change parameters and it is when I discovered that I completely forgot Root password and the other SU abled user account. Since everything is running from the eMMC, i cannot access to any fils in the OS as explain in some other discussion with card using SD card. Is there a way to recover…

I was searching for a UPS for the Banana classic and then saw you just can connect a battery to it. What i can't find information about if it needs to be unprotected or if i can use my protected Keeppower 18650 Li-Ionen's that i already have for my flashlight anyway. And is there anything special i need to do in Armbian? Just connect the battery and it works? Hard to find information :-(

hey guys, led folder is missing from /sys/class/ and even in /sys/class/gpio_sw/ led is included in fex file. can anyone tell how does linux load configuration from fex to orange pi ?

https://pastebin.com/jpG4iGtX Not sure what else more to say. I included the whole upgrade process including the restart in the paste above. I'll now prepare another sd card using a fresh nightly image and check if this boots normal or if nightly is currently broken at all. Edit: Yep. Current nightly is broken. Pretty much the same errors https://pastebin.com/pGAG1iUy Armbian_5.51.180708_Orangepioneplus_Debian_stretch_dev_4.18.0-rc3 Edit2 Armbian_5.51.180706_Orangepioneplus_Debian_stretch_dev_4.17.4 confirmed working.

Hi, How to enable TV-OUT on Orange Pi Zero in Armbian mainline ( 4.19.20 - 5.75)??? I saw a post from one year ago with a patch that adds an overlay called tve, but is there a more integrated solution by now? Thank you

Orange Pi Zero 2 After installation Armbian 22.02 Focal stopped loading. help me please in UART outputs the following U-Boot SPL 2021.01-rc4-armbian (Jan 05 2021 - 03:01:27 +0100) DRAM: 1024 MiB

Hi, Is there any sleep or low power modes in orange pi with soft wakeup I want to wake up Orange pi zero at some specific time. For that i go through some forums and searched alot about that but could not found any way to do this. I also go through some 'rtcwake' commands but they didn't work. Any Idea regarding sleep modes and how to wake up would be great help for me. Thanks,

I am using orange pi + 2e, the distribution version of ubuntu I am currently using. How do I start my device under 2 seconds, is there a suitable linux distribution? On the device I only use the python programming language, and some image compression and sending operations are being done.I shut down units like Wireless and Ethernet,Desktop but I did not get much acceleration. What are your suggestions? How much acceleration can I record if I start the version of the armbian mainline in ram disk?

Hello, I just use the Zero Plus 2 H3 with extension, using Armbian 5.83 but failed to get the combo to play the sound I use the command aplay -l but return no sound card found How to install driver for sound in this board?

I'm trying to establish usb serial communication between an Orange Pi PC2 H5 running armbian and a samsung galaxy note 4. I'm configuring the micro USB port on the Orange Pi with libcomposite and opening up an acm port. On the android end I'm using a library by mik3y (https://github.com/mik3y/usb-serial-for-android) to establish the communication. The trouble that I'm running into getting Android drivers to support USB serial communication with the H5. I may just be just configuring the orange pi wrong. Here is the libcomposite setup script: #!/bin/bash/ modprobe libcomposite cd /sys/kernel/config/usb_gadget/ mkdir -p g1 cd g1 echo 0xa4ac > idProd…

sudo systemctl status bluetooth ● bluetooth.service - Bluetooth service Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled) Active: active (running) since Sat 2023-02-25 16:50:52 IST; 1h 41min ago Docs: man:bluetoothd(8) Main PID: 1131 (bluetoothd) Status: "Running" Tasks: 1 (limit: 2209) Memory: 1.3M CPU: 402ms CGroup: /system.slice/bluetooth.service └─1131 /usr/lib/bluetooth/bluetoothd Feb 25 16:50:51 orange systemd[1]: Starting Bluetooth service... Feb 25 16:50:52 orange bluetoothd[1131]: Bluetooth daemon 5.64 Feb 25 16:50:52 orange systemd[1]: Started Bluetooth service. …

Hi, Since latest update just a few days ago (Linux bananapi 4.5.5-sunxi) , the bananpi keeps telling me this: [ 5 updates to install: apt-get upgrade] . When i try to upgrade there arent anything to upgrade. In did apt-get update and apt-get upgrade and nothing to upgrade. I manually execute /etc/update-motd/40-updates and its true that it says that there are 5 updates. So there must be something there that its not chaning. Any tips on this? EDIT: ok i just fixed this by manually editing the file /var/cache/apt/archives/updates.number and setting it to 0 but i think this should be automatic and it wasn't working for some reason. (seemed like the script wasn't updatin…

AFAIK, from last year, there are some new driver for AXP209/202 PMU for mainline kernel. One of the main new features that i really like is custom sampling frequency compared to the original driver for linux kernel 3.4 (i just remember the interval are 2 seconds). I want to use AXP209 PMU for power/energy profiling and consumption study of some SBC such as Banana Pi/Pro and some other Allwinner based SBC as comparison. The question is How i want to know current sampling frequency from PMU and how to change the frequency? (25, 50, 100 or 200Hz) What is the reasonable/best practice to write the captured power consumption value (with timestamp) into some logf…

Hi: I was using version 5.30 at orange-pi-pc and orange-pi-one. it is very stable. I saw some irq complain about 5.35, but I don't know if these issues affect H3 boards. I use the boards as headless server with openvpn and some DI/DO. is version 5.35 stable enough for the work? or I should stick with 5.30? thanks a lot for advice.

I have banana pi m2+ with ampak AP6212. Install Armbian 5.75 with Linux kernel 4.19.20 Driver on wi-fi brcmfmac. Wi-Fi access point actived via armbian-config. ifconfig: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.20 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::81:fcff:fe71:785b prefixlen 64 scopeid 0x20<link> ether 02:81:fc:71:78:5b txqueuelen 1000 (Ethernet) RX packets 76186 bytes 46503714 (46.5 MB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 12755 bytes 2691167 (2.6 MB) TX errors 0 dropped 0 overruns…

Hello, on a fresh install (Armbian_22.08.1_Orangepi3_jammy_current_5.15.63), the ethernet eth0 interface doesn't retrieve any IP. Here comes the kernel ethernet related messages: After that, I have launched a dhclient command that took several minutes to stop. Then, an APIPA address is attributed to eth0 nterface. So I have launched armbian-config to set the eth0 to static. And it worked. But how to make DHCP works? Thank you PS all others devices on my network can retrieve an IP by DHCP. I also tried others OS on my Orange Pi 3 boards and the…

Hey everyone! I just got myself hooked up with an Orange Pi PC+ and I was wondering is it possible to send files over the usb-ttl dongle just like in Windows Explorer, from my pc onto the eMMC or the external sd card, which is in the slot. I am using TeraTerm as console. It always boots up in boot0 mode. I have attached a piece of the log, that I've managed so far. Regards. putty.log EDIT: In teraterm there is an SSH SCP Send-Receive window, with path choises, but it doesn't seem to work. Couldn't transfer any file from the pc to the sdcard. Any thought, ideas?! Without using card reader at the moment. …

Requirements: https://github.com/lthiery/SPI-Py https://github.com/mxgxw/MFRC522-python (for Raspberry Pi) https://github.com/kwanxian/OrangePiPC/tree/master/SPI/RC522 (for Orange Pi PC) sudo armbian-config System --> Hardware --> select "spi-spidev" --> Confirm --> reboot when reboot finish: sudo vim /boot/armbianEnv.txt under "overlays=spi-spidev",add this: "param_spidev_spi_bus=0" save & reboot again. then you can see spi enable in "/dev/spidev0.0". cd ./SPI_Python sudo python3 setup.py install cd ../RC522 sudo python3 Read.py you can test IC card like this: …

Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux I have managed by accident to get full USB3 speed on orange pi lite 2. I have bought a USB3 hub: "Bus 004 Device 002: ID 05e3:0612 Genesys Logic, Inc. Hub" , I have no idea which chip it has, it is in an aluminum case and looks like the one on the attached picture but black. By attaching atleast two usb devices in the hub USB3 somehow gets into full speed mode, one of them has to be USB2 device. I have managed to get with all devices I have ATM about 2000Gbs including iperf in both directions with rtl8153, hdparm -t on two usb2 memory sticks …

Hello, my orange pi device crashes to white screen at random times. And in this case USB, ethernet does not work.Which logs should I look at?

Hello, about a month ago I got MangoPi QM-Quad - quite nice board, but with small support. Hardware specification: https://mangopi.org/mqquad Review: https://bret.dk/initial-mangopi-mq-quad-comparison/ I needed a raspberry pi zero board with usb-c with both host and otg ports and external wifi antenna - so after some consideration I want with Mango-Pi QM-Quad. Sadly after some work with available distributions I finally give up with trying to compile / build everything I needed and moved to getting Armbian to run on the board. Thankfully board is almost identical with orangepi-zero2 - so modification with edge kernel only required m…

Hello! I've built my own sbc using the Allwinner H3 chip, and I'm looking to get a custom armbian image running on it. I've already successfully compiled an image by adding a new config to u-boot and armbian-build, and a device tree to the linux kernel. Now I'm looking to get the WiFi working, but I can't seem to find where I can change its pin definitions. I'm using the AP6212: the SDIO pins are connected to SDC1 (aka mmc1) like every other board, but the WL_REG_ON (aka WL-PMU-EN) and WL_HOST_WAKE (aka WL-WAKE-AP) pins are connected to GPIO pins different from all other boards, so I'll need to change their pin assignments in the kernel manually. B…

Hi everyone, I got a problem with my beloved Armbian. I switched form a (SD-killing) Pi1 to a OrangePi. Everything runs fine except my Busware SCC (a RF interface for Homematic home automation). The module sits on the extension header and uses Pins 8 and 10 for the UART as well as pins 11 for reset and pin 12 for the bootloader. For the device to work normaly, pin 11 (GPIO17 on the rpi) has to be set high, else the device will stay in reset. Pin 12 I just left as it was on the rpi, the manual says I'm running ARMBIAN 5.36 with kernel 4.13.16-sunxi. If I understood it correct, pin 11 should be GPIO1. To set it high, I use the following code in r…

Hello, I want to use a 595N serial shift IC with my cubietruck over SPI. I tested it with a raspberry pi and it worked. But I want to use the SPI ports of my cubietruck to read sensor data and process some output over the 595N. But I didn't find a good documentation, how to enable SPI support on armbian with a cubietruck. My system uname -a: Linux cubie-rostock 3.4.113-sun7i #16 SMP PREEMPT Wed Jan 24 19:20:59 CET 2018 armv7l GNU/Linux I changed the [spi2_para] part in the fex file to this: [spi2_para] spi_used = 1 spi_cs_bitmap = 1 spi_cs0 = port:PC19<3><default><default><default> spi_cs1 = port:PB13<2>&…

good day everyone, Just for fun , i try to run gpu miner on OPI win plus, with open CL. https://github.com/hominoids/sgminer-arm but i face several problems and It would be nice if some buddy could help me. I cant install all needed libs: root@orangepiwin:~# apt-get install mali-fbdev -y Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package mali-fbdev https://forum.odroid.com/viewtopic.php?f=98&t=29571 To install Download ARM Computer Vision and Machine Learning library, is that value true: usr/lib/arm_compute-v18.03-bin-linux/lib/linux-ar…

if anyone is interested https://github.com/igorpecovnik/lib/issues/311

I need small serwer and i need a AP wifi and dhcp for wifi clients. Anybody can help me and show configuration file to setup Wifi Hotspot and dhcp program (meybe dns lokaly for better communication, my eth0 is slowly) I using Orange Pi Zero

Recently I tested armbian stretch for orange pi lite2. If there is not other task except system, there work fine. But if there are some high cpu tasks, such as unzip, the system load will go high, and not go to lower level when task done. When the system load is higher than 4, the response of the system is laggy, when go higher, the system will go no response. I use uptime to test the system load, when boot, the 1min load will be at 3.xx and go down slowly. When no task, the load will lower than 0.5.

hello , I have Opi lite 2 I want to use it as low load server with minimal power consumption (min temp) I edited /etc/default/cpufrequtils like that min_speed=120000 max_speed=480000 governor=ondemand but it works on 888mhz constantly with load and without load (image 2) Ps: I have also OPi PC+ and edit of cpufrequtils works ok on it (image 1) what am I do wrong, or maybe armbian-config monitor doesn't work properly ? ARMBIAN 5.67.181202 nightly Ubuntu 18.04.1 LTS 4.19.4-sunxi64

Hi, sorry, I searched the forum but couldn't get any definitve answer to my questeion.... Is Video Decoding Hardware acceleration, CEC control and HDMI Audio Pass Through working on the OrangePiZero3 device? Thanks to its gigabit ethernet it would be the perfect replacement for my cheap amlogic Box which does only 4K25P due to hardware limitations..... Thanks for your input regarding this topic! Cheers Ford

Hi guys , I am a newbie for armbian. I want to set my Orange Pi One as NAT server via USB connected to IPhone or Android Samsung . -------- Frist , I try to install Armbian_5.30_Orangepione_Ubuntu_xenial_default_3.4.113 Second, sudo apt-get install ipheth-utils Third, Connect to my iphone 5s via USB port and start my hotspot BUT I failed to set my phone as hotspot , I can't ping to www... I don't know what's wrong ? May any one give me a hand

After some hack, I use the SPI port on OPi One to connect with a MAX6675 board. The SPI port on One is SPI0, so armbianEnv.txt should include these: overlays=spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=0 the MAX6675 connects to OPi One as: MAX6675 One GPIO ------------------------------------------ VCC PIN17 GND PIN20 SCK PIN23 CS PIN24 SO PIN21 Then use the attachment program to read f…

Hi, I a couple of days ago, I picked up the Mainline 4.9.7 Jessie image. It ran flawlessly untill last night when I installed samba/minidlna and mounted my hdds (3 usb hdds on a powered USB3 hub and 1 sata 3.5in hdd). When the minidlna was updating its library and keeping cpu usage up and while I was doing some network traffic the CT froze. I thought this was a physical network issue and I bonded the wlan0 and eth0 so that wlan0 acts as backup when eth0 is down. Usually I log on with ssh and keep this headless, but I remembered that I had the tv connected to the hdmi. I attached a pic (sorry for the quality) of the error message. It seems som…

Hi friends, I have read a lot document about booting orange pi zero over usb flash. I flashed latest mainline u-boot to orange pi's SPI Flash. I can boot the system via the usb port which is next to the ethernet. Can I boot the system via the usb ports USB2 and USB3 that the h2+ has and the expansion card that can use it?. I can not see these USB's through u-boot terminal. thanks.

Hi all! I have Orange Pi Zero with armbian kernel 4.14. i'm not sure about the topic name, but to me seems like that. I've managed to make spi tft work flawlessly on my zero. But after i've continued with touchscreen module, i've got problems. After X is started, i can confirm touch is working, because when i touch the display, mouse pointer moves. But in the strange way, very laggy (more than a second to respond), but is works only for ~10 secs, then display stops to redraw. And it is not because of bad contacts! Because i've soldered everything together. And it also freezes if i don't touch it. The system is still working tho,…

Guys! I have two of the original Pine64+ boards from the kickstarter (with LCD) and tried to launch the latest armbian image on them. Both of them freezes in u-boot after it tries to evaluate USB connections... Rather strange, they work well with the ancient original images. ``` U-Boot SPL 2019.10-armbian (Feb 17 2020 - 09:25:19 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.2(debug):9560593-dirty NOTICE: BL31: Built : 09:25:06, Feb 17 2020 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4095dd0, model: Pine64+ INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controlle…

I had to reapply u-boot image. So, I did it by armbian-config and later by "dd" command. In both situations this is failing (please see u-boot messages printed by serial). I was restoring the image (I have backup images of my SD card) and trying again. What may be the problem? I had linux-u-boot-orangepi*-current 22.08.6 installed. As below - please note Verifying Checksum ... Bad Data CRC BTW. I tried the same on Orange Pi PC and Orange Pi Zero - the same result (fail to boot). => version U-Boot 2022.07-armbian (Oct 18 2022 - 07:35:20 +0000) Allwinner Technology arm-none-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Archite…

Current UWE5622 driver(from the extension) will trigger a kernel warning raised by `void dev_addr_check(struct net_device *dev)`. The following patch seems fix the problem. The bug reporting guide told me not to post this to armbian/build so I decide to make a shout in the forum. diff --git a/drivers/net/wireless/uwe5622/unisocwifi/main.c b/drivers/net/wireless/uwe5622/unisocwifi/main.c index bf2ec6c..b83ab8e 100644 --- a/drivers/net/wireless/uwe5622/unisocwifi/main.c +++ b/drivers/net/wireless/uwe5622/unisocwifi/main.c @@ -15,6 +15,7 @@ * GNU General Public License for more details. */ +#include <linux/etherdevice.h> #include "sprdwl.h" #incl…

Hi, for my project I need to stream a video from IP camera and add some text from sensors into the final video. From armbian console I have installed ffmpeg (apt-get install ffmpeg).. The program works except the text is not included into streamed video: Example: ffserver.conf HTTPPort 8090 HTTPBindAddress 0.0.0.0 MaxHTTPConnections 2000 MaxClients 1000 MaxBandwidth 10000 CustomLog - <Feed monitoring1.ffm> File /tmp/monitoring1.ffm FileMaxSize 50M ACL allow 127.0.0.1 ACL allow 192.168.0.0 192.168.255.255 </Feed> <Stream monitoring1.mjpg> Feed monitoring1.ffm Format mpjpeg VideoCodec mjpeg VideoFrameRate 22 VideoBufferSize 80 VideoSiz…

Hello everybody, I would like to know what needs to be done to make this work. I simply copied over the sources of the r3p2 mali module into the 3.4.113 Armbian kernel source and the module wos built without error. Then I recompiled libump, libmali and fbturbu. But when I tried to put the gpu to work I got an error message: eglgetdisplay() returned no display. Since there was nothing helpful in the logs I coudn't investigate further where the problem lies. Has anybody had success with the newer mali drivers? Any hints are very welcome...THANKS! Paul

Hi, I would like to know if there is a way to set the display resolution to 640x480, to use with an old CRT screen from a IBM PS/1 model 2011 that I want to revive. I know about h3disp, but it only has high resolutions, and that old screen does not want to sync correctly to anything other than VGA. I use an Orange Pi One, with a HDMI to VGA adapter and Armbian 5.35, with legacy kernel 3.4.113 Thank you! -Alexandre

Hi, I am running Armbian on my Pinebook and want to install Kodi version 17. In official repository only version 15 is available. Is it possible to install version 17 and if yes, please tell me some instructions. Thank you in advance.

OrangePI PC2 Problem report of the current state and improvement favor. --------------------------------------- Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop Keyboard and the monitor resolution.. other All kinds' setting, reboot, when, everything goes off. Therefore it isn't used. --------------------------------------- Armbian_5.34.171121_Orangepipc2_Ubuntu_xenial_next_4.13.14_desktop A keyboard is the monitor resolution only. It's preserved and it's practicable somehow. (1) Setting of other than above, reboot, when, please disappear. I close. (2) Cash of Root becomes full right now, even Mozc, install, can. ---…

I have a NanoPi Neo Core and I'd like to analyse the SPI controller driver and why it toggles the lines the way it does. In the overlay file, all I see are mentions to 'spidev'. Where can I find out why the data lines shown below toggle the way they do? I.e. chip select goes low way before the clock line. The MISO line has a droop to GND briefly and the CLK line hangs high for a while before toggling... Thanks forum :). YELLOW: CS PURPLE: MOSI BLUE: MISO GREEN: CLK EDIT: I'm sending two bytes, 0xDA, 0x00 at spi mode 3. Ignore the decoder, it was set to read LSB first.

Hi. Kernel version : 4.11.7-sun8i My trouble is that clk is weird in using spidev. This is a oscilograph when i send a command with spi. First line is CLK and second line is CS0. My slave chip can not receive commands. and I think it due to this weird CLK. CS seems affect CLK. I just want to use spi with CS keeping active-low. But, following code setting mode of spi occured an error. "invalid argument exception" mode = SPI_MODE_1 | SPI_NO_CS; if (ioctl(file,SPI_IOC_WR_MODE32,&mode)<0){ perror("can't set spi mode"); return; } this work properly. mode = SPI_MODE_1; if …

I recently started playing around with OrangePi Zero with the Allwinner H2+ CPU. I want to test out the internal audio DAC. To do so I enabled "analog-coded" in armbian-config. After rebooting I saw a new audio device in the output of "pacmd list-cards", but it says that only mono is available. How can I configure stereo sound? I haven't played around with "/etc/asound.conf" much as I don't understand it. Also, I don't have anything plugged into the audio pins on the GPIO.

Hi, after a long search, I found how to use the display driver without fbtft https://www.raspberrypi.org/forums/viewtopic.php?t=124961 I used the display 3.5in TFT witch SPI on the OPi PC on Armbian jessie. lcd on ali: http://www.aliexpress.com/item/High-end-3-5-LCD-Touch-Screen-Display-Module-Board-320x480-RGB-For-Raspberry-Pi-2/32611946526.html?spm=2114.30010308.3.21.j1gFEx&ws_ab_test=searchweb201556_8,searchweb201602_2_10048_10047_10037_10017_10046_10033_10045_406_10032,searchweb201603_1&btsid=057be304-5a97-4dff-9905-87cf320dcb67 After some refinement because this interface is very very slow my modified code is attach https:…

I know that now mainline kernel is supported on orangepi zero so is there any way to activate the composite video output.?

Hi all! I may need some pointers. I'm using a 2.4" LCD at spi1 which works as /dev/fb0 on armbian bookworm (6.1.63) Meanwhile I've learned frambuffer is deprecated and to be replaced by drm., but ... - I could not find enough details to understand the drm architecture in general - there is a linux/drivers/gpu/drm/tiny/ili9341.c how is that used at all? - How to use drm in armbian? For my case any acceleration is not necessary (and likely not possible even if the H3 has Mali Hardware) but I want to avoid further changes if /fbX is really gone. btw. I want to add touch with shared SPI soon, work in progress. …

https://github.com/MaverickLong/MLIR-TIM-VX This is an MLIR-based lowering path from the TOSA v1 dialect to TIM-VX, VeriSilicon's OpenVX-based GPU/NPU ML Framework. It includes the lowering from TOSA v1 to a custom timvx dialect (mirrors the TIM-VX C++ semantics) and a full lowering to C++ source. It is currently on par in inference speed with the vendor ACUITY compiler pipeline while still giving you full control on the graph level. In my own testing, on a Radxa Cubie A7Z \w Allwinner A733, ResNet-50 takes 8.0ms to inference, while the ACUITY-compiled baseline takes 7.3ms according to Radxa. It all starts with Radxa/VeriSilicon's fa…

Hi, First of all: Thanks for the great work. I have installed the Armbian_4.5_Cubietruck_Ubuntu_trusty_3.4.109_desktop image and it runs smooth so far. After a while beeing idle the monitor goes black as it should, but the cubie doesn't wake up on mouse or keyboard entry. The only thing working is a reboot. Also I'd like to know, how I can deactivate the Micro-USB port. If I remember it right, this is responsable for the low volume high pitch noise. Thanks for all your responses. kauppi

Hello. I am using baresip for SIP communication. I have faced a problems with audio USB adapter (http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141629380416) with C-media chip. I have set it as default sound card. I make a call using baresip. Until I answer the call on another device it works, it rings. But when I answer, kernel errors occurs and Orange Pi hangs (cannot do anything): Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.378730] sunxi oops: enable sdcard JTAG interface Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.380906] sunxi oops: cpu frequency: 1008 MHz Message from syslogd@localhost at…

Hi all, Today I decided to pull my OPi Zero H3 out of its box and fire it up. Downloaded and installed Armbian Stretch mainline kernel 4.14.y to a SanDisk micro sdcard grade 10 and powered it up with a known good 5v 3a power supply I've used to power my OPi Zero's via GPIO (with all my Zero's I've soldered in GPIO headers - something I'm used to doing with RC helicopter and multirotor flight controllers). Connected my USB hub with keyboard and mouse connected. Disconnected my OPi One (RetrOrangePi gaming computer) from its HDMI connection and connected it to my Zero H3 and powered it up. Boot text is on display nice and clear. Then the …

Hi, i have managed to install a wiring Pi version for my Orange Pi lite following this tutorial: https://gist.github.com/lanefu/f16a67195c9fa35c466c6b50cdaeadea The basic examples with inputs and outputs are working fine. Since I want to use a rotary encoder and not loose any steps I want to use a interrupt driven callback. There is an example as well but that does not work. I get: wiringPiISR: unable to open /sys/class/gpio/gpio25/value: No such file or directory I also tried several other libraries but non was working. Has anybody managed to get GPIO interrupt based callbacks working with python an an Oragnge Pi ?

Hi evryone. I try to load camera module ov2640 using modprobe and get following error: root@orangepione:~# modprobe -v ov2640 insmod /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/soc_camera.ko modprobe: ERROR: could not insert 'ov2640': No such device Do you have any ideas how can solve this problem?

Dear Armbian team, I am using debian stretch with orange pi PC ( Linux orangepipc 4.19.38-sunxi #5.83 SMP Fri May 3 23:33:25 CEST 2019 armv7l GNU/Linux ). At the moment by default when I press the power button, it shutdowns the orangepi pc, and I have to plug off/on the power supply to reboot the device. I would like to modify this behavior, to program custom actions when the button is pressed. If possible it would be nice to be able to distinguish between short press and long press. I tried without success to follow the manual instructions, and add the custom overlay gpio-button.dts. Also tried the acpi package approach without a…

I got myself a Banana Pi M2 Zero (with H3 chip) and am running Armbian (Armbian_21.08.1_Bananapim2zero_buster_current_5.10.60) on it. I have enabled SPI by adding the spi-spidev dt overlay. Now I want to use both CS pins at the same time so that I can connect two devices. The spi-add-cs1 overlay doesn't change anything so I researched a bit and found this custom overlay. Unfortunately it didn't work too and there is still only a single spidev available. Is there any way to enable both of them at the same time?

Hi Igor, while playing with your Armbian and kernel to squeeze even more juice from my cubietruck, i would ask you if you think it would be possible to add to your kernel and u-boot build the support for KVM. Here one experiment with KVM: https://rwmj.wordpress.com/2013/12/13/kvm-working-on-the-cubietruck/ Then, partially related with this, it would be nice to have the watchdog enabled to fight the occasional low level hang that happens sometimes (all freezed with 4 led on).

Someone know how install step by step Glmark2-es for armbian ( Orange Pi PC ) ? I tried compile but no result

Hello guys here is a couple of questions regarding Mali/EGLFS on OrangePi One and Armbian v4.4.*. I am going to cross-compile and use Qt5 Embedded on Armbian v4.4.* and I strongly need QML engine for my development which requires eglfs plugin. Is Mali GPU supported on this version of OS ? How/where to get/compile user mode libraries (EGL+GLESv2) for this version of OS ? Thank you

Hi everyone, has anyone tried to make the above mentioned tuner work with Cubietruck? If so, were you successful? Again, if so, what are the necessary steps? It should be possible with kernel 4.11, since the latest LibreELEC distribution includes the drivers in kernel 4.9. Help would be appreciated! Thanks and cheers, chessplayer

Hi folks Im facing with strange behavior of my cubie a20 Im booting it from sdcard since mainline armbian not support emmc (as far i know), but it boot from sdcard only when FEL button is pressed. Without FEL pressed it boot into android from emmc. In documentation i read if sdcard is present cubieboard tries boot from it which is legit. This behavior sucks when power loss occurs. My home-made router with some other stuff is offline and all other is offline. I expect to always boot from sdcard or emmc if i flash it with latest armbian. Please help if you can

Hello. Can anyone provide any hint about configuring dts for sun7i, please.

Image of Armbian buster 4.19 Does not work on pine64 A64 2G. There is only a black TV screen. No image problem Armbian Xenial 4.75. help

Hello, i tried "Armbian_community_26.2.0-trunk.606_Radxa-cubie-a5e_trixie_edge_6.19.8_minimal.img" and wlan didn't work, i think the device tree is broken Radxa-cubie-a5e kernel 6.19.x as a quick fix, I copy the kernel 6.18.x "sun55i-a527-cubie-a5e.dtb" file to the /boot/dtb/allwinner directory to get wlan working.

Hello dear mates, first I want to thank zador.blood.stained for helping out with recompiling the DTB for A20 so we can enable PWM on Armbian. Link to his post :https://forum.armbian.com/index.php/topic/1817-using-pwm-without-rebuilding-kernel/ Now I'm seeking your help with this problem, after I added this code to the A20.dts file (I'm on a PCduino3 nano) &pwm { pinctrl-names = "default"; pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins_a>; status = "okay"; }; I'm able to compile the .dtb file, and after booting I can see the pwmchip0 on /sys/class/pwm. I can change the values for Polarity, Period, Duty_Cycle, Enable. The problem is, when I…

I have installed the latest stable Ubuntu desktop Legacy on BPI M1. The OS boot directly into the GUI. I am planning to use xrdp to remote desktop into OS from windows machine on same network. So I think it will be a good idea that BPI to boot directly into console to save some memory. If I need GUI then I can remotely connect from a windows machine. Is it a good approach? If yes, then how to configure to boot into console with minimum memory footprint.

i have an Orange Pi Zero. I add a simple Soundcard with sound in to the USB. I want to stream the sound comes from the AudioIn (usb) in to my local Wlan. What do i need? Is it possible with icecast2, darkice and Pulseaudio like in this Tutorial: https://michaelfranzl.com/2013/11/25/audio-streaming/ ?? or there other ways? thank you for help.

Hi form germany, i have problemes with my M1. The system hangs and only ping is working here the last timestamps: do, 14.04. 18:00 so, 01.05. 2:45 do, 05.05. 3:00 mo, 09.05. 15:22 i use Armbian 22.02.1 Focal with Linux 5.15.25-sunxi homeassistant + portainer (docker) mosquitto samba with sata 500gb ssd do we need some other logs? thanks to this nice work 🙂

Hello again... How can I activate the wifi network? I have a nanopi neo plus 2 with wifi, but armbian don't find it. Ifconfig and nmtui don't find the wireless connection. Thank you

Not sure if my keyboard is working in DESKTOP. Do I need to to install it? Though it is working in command prompt and retro. If not, how do I use it without a mouse? in Windows, you could tab/alt/spacebar/enter and etc but none of this works. Keyboard works in command prompt

Setup: Orange Pi One 16Gb SD card Running Armbian Stretch (Mainline Kernel 4.14) Using XFCE4 Desktop Environment eGalax Touch based 1503M 15 Inch 1024*768 Monitor HDMI (IN - FROM Pi) to VGA (OUT - TO MONITOR) Adaptor I have the monitor setup and working, everything boots through to XFCE however the touch panel is inverted and the 'active area' is smaller than the screen. Although the touch panel is responding I have the following issues X and Y crossed over Both Axis Inverted roughly 2cm 'Dead Zone' on the perimiter of the screen I have attached it to my laptop and the sc…

Preamble: I have done numerous hours of reading and searching (due diligence). See end. I have a FA NanoPi NEO Core-2 LTS with shield and 64G M.2 (This shield uses JMS567-LGBB1A chip USB to sata for M.2 access). I have successfully installed Armbian from SD to and booted from the eMMC. Armbian Stretch mainline kernel 4.14.y - This image https://dl.armbian.com/nanopineocore2/Debian_stretch_next.7z armbianmonitor -u results http://ix.io/1xAA Logs indicate formatting did occur correctly as far as I can tell. The volumes are formatted as I selected - along with an 'extra' ext4 volume that looks like it is just for boot. NOTE: Since…

raw_gadget compile failed make make -C /lib/modules/5.15.93-sunxi/build M=/root/raw-gadget-master/raw_gadget SUBDIRS=/root/raw-gadget-master/raw_gadget modules make[1]: Entering directory '/usr/src/linux-headers-5.15.93-sunxi' MODPOST /root/raw-gadget-master/raw_gadget/Module.symvers make[3]: *** No rule to make target '/root/raw-gadget-master/raw_gadget/raw_gadget.mod.o', needed by '/root/raw-gadget-master/raw_gadget/raw_gadget.ko'. Stop. make[2]: *** [scripts/Makefile.modpost:139: __modpost] Error 2 make[1]: *** [Makefile:1820: modules] Error 2 make[1]: Leaving directory '/usr/src/linux-headers-5.15.93-sunxi' I cat Module.sysmvers in /usr/src/linu…

OrangePi Zero (512 MB) Power from 5V 2A supply, connection via Ethernet. Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113 I am not strong on CLI so I have installed "lubuntu-desktop" and "gufw" and set them up. I also have NoMachine's Remote Desktop server installed, to share the Zero's virtual screen with my LAN. The project is to assess the Zero's ability to run a low volume mail server. So I have used the iRedMail script to install and set up the components of the mail server. It seems to be working - I have received the standard opening 4 emails OK. The problem lies with connecting to the Zero to find out what it's doing. …

I did a apt-get upgrade with the current Ubuntu/Debian images and the wifi sharts on the 512MB Duo. Didn't see anything in syslog to indicate an issue. A temp fix is to freeze the kernel updates in armbian-config.

need help to drive Orangepi pc plus with waveshare 3.5inch display with xpt2046 touch driver. OS:- Armbian 22.11 Jammy XFCE Desktop version Kernal :- Kernel 5.15.y link for the os :- https://www.armbian.com/orange-pi-pc-plus/ link for display :- https://www.waveshare.com/3.5inch-hdmi-lcd.htm can any one help to drive touch screen you can message if you need more information,

Hi, I need a help. I have waveshare 4inc lcd touch play display but I don’t know how to enable touch play. Please Help me.

Hello Everyone , Can anyone please guide me . I need to use nano pi neo's USB pins(2.54mm x 2 header pins) and looking for resources related to it. I am using armbian OS on it. I am struggling with it , I read many resources on the web but none of them provide detailed information. Any help will really be appreciated !! Thanks so much!!

I am trying to enable Winstar TFT display on Olimex Lime2 board under the kernel 5.4. Display spec is here: https://www.winstar.com.tw/products/tft-lcd/ips-tft/lvds-tft.html Up to the day we've been using the legacy kernel 3.4 and the display worked fine -- the u-boot was compiled with the settings (CONFIG_VIDEO_LCD_MODE, CONFIG_VIDEO_LCD_POWER etc) suggested here: When I try to use the same settings in the mainline sources of armbian, the display does not work. I've enabled backlight with a DTS overlay and the backlight works but the display stays blank. Here is the output of dmesg: [ 2.846134] printk…

Hello On my Banana PI infrared receiver is not detected at bootup. I'm running armbian 4.7 jessie. The only /dev/input device is that of axp20x-pekj, which I undestand to be a power controller. My issue is similar as found in this thread: http://forum.armbian.com/index.php/topic/475-bananapi-r1-no-infrared-device/ Except ofcourse the board is different From the other thread I gather I need to change something in regards to dtb-s, but I guess as the boards are different using the same one as mentioned is not a good idea.

I use two Orange pi PC for music studio use with Jack, Ardour and several midi software to use with midi surface controls and keyboards. Everything works great with an external USB DAC but when I try to use the on board DAC through the HDMI output the sound comes out slowed down to maybe a third of the speed making everything sound like it's in slow motion. Any help to fix this would really be appreciated.

Using Firefox Send, expires after 7 days / 100 downloads. My own build - works nicely for me & installs to eMMC. 203.6 MB compressed. Use xz to decompress. Filename: Armbian_5.77_Orangepi3_Ubuntu_bionic_dev_5.0.4.img.xz https://send.firefox.com/download/e2961cb805fba655/#rquCw2FsaPvGQpVviByLHA

I am listed as the community maintainer for the Banana Pi M2 Zero. I haven't actually done any maintaining but I am thinking about doing so now. But before I do, a couple of quick questions. 1) The latest build (as far as I can see), is Aug-31st, 2023. Do I have that right? Or am I missing something? 2) The main page for the Banana Pi M2 Zero (https://www.armbian.com/bananapi-m2-zero/) shows a link to Armbian_community_24.11.0-trunk.273_Bananapim2zero_bookworm_current_6.6.54_minimal.img.xz which is for "Minimal/IOT images with Armbian Linux v6.6". Is that a generic build for all community maintained sunxi hardware? Or is that a specific Banana Pi M2 Zero …

Greetings - I'm trying to use the UART2 port (Connector J11 pins 1 and 2) and I'm not having much luck with Armbian 5.0 Vanilla. There are /dev/ttyS0-7 listed, but I get nothing from them (save ttyS0 which is the main console and in use by getty). I found several other articles in here talking about how to expose the GPIO pins, but I could not see how to set the "mode" of them. Any assistance would be appreciated!

Hi, After the new update, the BLUE LED on the nanoPI M1 is not being used anymore. Cheers,

Good day, everyone! On the manufacturer's website Allwinner H5, it says: 2 Display device, dual display (same or different content) HDMI & CVBS. Can anybody tell me how to do this? I'm willing to pay for the development of drivers and / or firmware to be able to work on an Orange Pi Zero Plus 2 H5 device with two displays (1- HDMI, 2-TVout) - at the same time. With suggestions, please contact me at tigroidit@gmail.com

Hi all . i write down about armbian at the last part of http://orange-pi-2.blogspot.jp/2016/01/orange-pi-2g.html in English . anyway armbian support minidlna well , so i enjoy video by vlc ( =dlna client ) . https://www.youtube.com/watch?v=vpMs9TOdgu0&feature=youtu.be ---- regards , tuyosi

I'm working in a project that needs to use 12 GPIO pins (plus serial!) on the Orange Pi Zero. To achieve that, I need to disable at least one of the I2C interfaces in the 26-pin header. Following the instructions on https://linux-sunxi.org/I2Cdev, I have decompiled, edited and recompiled /boot/config.bin, but I still can't access any of the pins used by the I2C ports. Specifically, what I have done is to edit the decompiled script.bin.fex file, and in sections named [twi0] and [twi1], changed twi_used=1 to twi_used=0. After that, running a simple program that sets the pins to input and reads its status allways returns 1, even if the pin is connected to ground or…

I have an Orange Pi One, with Armbian installed. *sometimes* when I log in it displays: "Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi" Then some system statistics and a line with the CPU temperature, for example: "CPU temp: 58ºC" I can also get the current temperature with armbianmonitor -m or reading a file called "temp" in a directory under /etc/system (I don't remember the full path now). If I log in again, I see again the temperature in the welcome message, running armbianmonitor or reading the aforementioned file. Until I shutdown and boot again. Then, all 3 methods of getting t…

Hi, I've been getting a journal file full of this kind of entry lately, which is using up all my memory until I get an error "no space left on device". I have two Cubietrucks, this is only occurring on one of them, both running mainline kernel and both up to date. The one causing problems has a 2.5" hdd mounted via the sata connector. Oct 16 11:27:35 stpeter.nentura liblogging-stdlog[1048]: action 'action 12' resumed (module 'builtin:omfile') [v8.24.0 try http://www.rsyslog.com/e/2359 ] Oct 16 11:27:35 stpeter.nentura liblogging-stdlog[1048]: action 'action 2' suspended, next retry is Tue Oct 16 11:28:05 2018 [v8.24.0 try http://www.rsyslog.com/e/2007 ] …

Hello, I have spent a lot of time, trying a lot of Armbian versions, looking on a lot of dedicated topics, building Armbian... and I still cannot display a desktop on the 3.5" gpio lcd (XPT2046) So, I post this topic for anybody can or would like to help me please... Olivier

Dear Forum, First of all thank you for being a member here. Second is that I would need some help on selecting an image for my present CT board. I need the followings: 1. hostapd with dnsmasq 2. g_mass_storage 3. sata 4.spidev or equivalent Preferably: 3. I would need free up SD card slot, so nand or SATA boot would be preferred. Which image is the best for me even if I need to recompile it? Thank you in advance.