Allwinner sunxi

In case anyone wondering, AW859A / 20U5622 Wi-Fi modules (uwe5622 driver) do not support WPA3. GCMP-128/GCMP-256 are not listed as supported in iw output, SAE or WPA-PSK-SHA256 wpa_supplicant key methods are not recognized as valid. # iw phy Wiphy phy0 wiphy index: 0 max # scan SSIDs: 12 max scan IEs length: 2304 bytes max # sched scan SSIDs: 9 max # match sets: 9 RTS threshold: 2353 Retry short limit: 10 Retry long limit: 9 Coverage class: 0 (up to 0m) Device supports RSN-IBSS. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5…

Hello dear members, I have built complete mainkernel on orange pi zero. I compiled u-boot, busybox, mainline kernel, and obtained dtb file. So, my pure system is running now. But, I do not how should I continue? For example, how can use wi-fi, how can use gpio drivers and how can import some libs like wiring pi to my pure system. What is next for development? Best Regards.

I am searching for an LCD 10 inches or above that works with the LCD connector on the Orange Pi Win Plus A64. Does anyone know of one that works and can you provide a link to it so I can purchase and use it? Thanks.

Hi. I would like to know if someone can help me. I was successfully able to compile armbian 6.6.30 with all of @Stephen Graf patches for my orangepi zero 3 having Full Audio working even on HDMI. see below for reference. Now I have a 2nd project. It runs the h616 with 2GB DDR3 RAM with AXP313. Can someone help me with a patch for the AXP313 on h616. Or alternatively, could my h618 orangepi zero 3 setup work if I patch it to run with DDR3? If so where can I find such a patch. Thanks in advance.

As the title says, my OpiPC don't want to boot. It starts to boot, with UART console I can see u-boot loading and doing its job, but just when it would start the kernel the console gets borked with non-ascii characters. After this, the board just hangs there. I've tested with 3 different images (written out by Etcher), checked the images checksum and checked the SDcard with F3. This setup worked fine a month ago, when I last had the time to play with it. Since than, the board was just lying on my desk, turned off.

Hello, everyone. I searched long time to run cocos2d on Armbian_5.38_Orangepizeroplus2-h3_Ubuntu_xenial_default_3.4.113_desktop. Now it run but very slow because device is orange pi zero plus 2 (mini com like arm). when build project, it automatically works for desktop with opengl. We already compile & run new cocos2d-x-3.15.1 cpp project on Armbian. FPS is 30. If we make this project work on opengles, fps will rise. Have you got issue? I guess if i change this to opengl es then speed will be ok. Because on Android on same device, apk's fps is 60. Please help me.

I have 1 "Customised Olimex Lime A20 SBC with RTL-SDR chip installed in the board (AirNav XRANGE). Currently the OS I'm using is the Lime A20 Armbian Stretch 4.14.84, everything is works fine except for the 2 GPIO LED. I have no idea how to let it work. I have the edited "sun7i-a20-olinuxino-lime.dtb" from Armbian Jessie 4.11.5 which is mainly for the board. May I know is there a way to incorporated the "Armbian Jessie 4.11.5's sun7i-a20-olinuxino-lime.dtb into the A20 Armbian Stretch 4.14.84 so that the 2 LEDs will work again? The edited dtc for LEDs to work "sun7i-a20-olinuxino-lime.dtb" attached. Hope to get so…

I've seen this question asked quite frequently here and all the posts end before there is a solution. I think it's time we had a crystal clear discussion on how it can be done. Not just for my curiosity, but for the people who've asked before and for the people who will ask in the future. The reason: Many hats/shields designed for RaspberryPi would otherwise be compatible with OrangePi if Armbian/u-boot didn't direct the debug output to UART0. UART0 is the most commonly used serial connection for hats/shields designed for RaspberryPi. OrangePi has multiple UART gpio so it would make sense for the O.S. (Armbian) to use the one that least impacts the…

Hi i wonder why ISR result is strange first i test in orangepi zero Plus H5 that result is repeated infinite recall function summary - recall infinite function if i input interrupt pin(button) i test result repeat second i test in orangepi zero(H2) that result is only called function once #include <wiringPi.h> #include <stdlib.h> #include <stdio.h> #include <unistd.h> void signal_both(void){ printf("Signal Both\n"); }void signal_falling(void){ printf("Signal Falling\n"); }void signal_rising(void){ printf("Signal Rising\n"); }int main(int argc, char **argv){…

Hello, [OPI PC+] u-boot : starting USB... don't start automatically what i did: - got 'Armbian_5.35_Orangepipcplus_Ubuntu_xenial_default_3.4.113.img' - extracted 'u-boot-sunxi-with-spl.bin' from above .img and put it on some USB key - booted from SD card with Armbian 5.35 (above) - wrote 'OpenELEC-H3.arm-7.0-devel-20161026221641-r23113-g64b34b3-opipcplus.img' on eMMC: dd if=/mnt/usb/OpenELEC-H3.arm-7.0-devel-20161026221641-r23113-g64b34b3-opipcplus.img of=/dev/mmcblk1 conv=notrunc,noerror bs=4k (boot okay without SD) - and finaly, wrote u-boot & SPL onto the eMMC: dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk1 bs=1024 seek=8 …

I'm trying to use the kernel-driver (1) for a DHT11 (or DHT22) humidity sensor with my NanoPi NEO. I'm already got this sensors working with some little C example-programs in userspace. I figured out that I need to apply a Device Tree overlay because the driver (dht11.c) needs to know the gpio-pin where the sensor is connected to. So - I don't know how to write such a file from scratch - I customised a existing overlay file - "sun8i-h3-pps-gpio.dts" (2) - only the lines "pins" (PG6) & "compatible with" (dht11) & "gpios" (&pio 6 6 1) /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { …

Hello. After burning Efuse to the Nanopi Neo Core, I can't boot from emmc. It works from the SD card, so I try loading everything into emmc: spl, uboot. But spl doesn't find u-boot, as far as I understand. I'm using the u-boot and dts config from the Nanopi Neo, with some edits to mmc2, since it's not available in the Neo. U-Boot SPL 2024.07 (Feb 25 2026 - 15:51:42 +0300) DRAM: 512 MiB Trying to boot from MMC1 CMD_SEND:0 ARG 0x00000000 MMC_RSP_NONE CMD_SEND:8 ARG 0x000001aa RET -110 CMD_SEND:55 ARG …

Hello! when I connect to the OrangePi mini TV / AV, TV wrote "no signal" If you connect to hdmi ok FEX: [disp_init] disp_init_enable = 1 disp_mode = 2 screen0_output_type = 3 screen0_output_mode = 3 screen1_output_type = 2 screen1_output_mode = 11 fb0_framebuffer_num = 3 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb1_framebuffer_num = 3 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 [tv_out_dac_para] dac_used = 0 dac0_src = 4 dac1_src = 5 dac2_src = 6 dac3_src = 0 and [tv_out_dac_para] dac_used = 1 dac0_src = 4 dac1_src = 5 dac2_src = 6 dac3_src = 1 [tvout_para] …

I can get WiFi working on the M2+ but not with encryption, I am using the latest Armbian has anyone had wifi success with this board ?

Hello, [OPI PC+] u-boot : boot.scr issue Oracle VM: Linux cross-compilation 4.10.0-42-generic #46~16.04.1-Ubuntu SMP Mon Dec 4 15:57:59 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux DS413J as DHCP and PXE/TFTP server with these files (copied from /dev/mmcblk0p1) on the TFTP root: boot.scr (mine but original one works well) script.bin KERNEL Same issue if i put my boot.scr onto the eMMC... Every single command works well on u-boot prompt. boot.cmd as follow, compiled with this command from Armbian doc: # OpenELEC Boot (philip63 - 02.12.2017) gpio set PL10 gpio set PA15 setenv machid 1029 …

Hi, my 1st post here. I have serial over OTG between Win10 PC and Zero working, fine as long as I use it for console login. (serial-getty@/dev/ttyGS0. If I stop the getty service, No usb/com port is opened @ PC side, when I plug it. I still see the /dev/ttyGS0 on the PI (stty -F/dev/ttyGS0) but apparently the device is not opened to the external world. I would expect that any send command to the device would open it, e.g. ls > /dev/ttyGS0, but nothing opens at the Win10 PC. What does getty do, so that the PC discovers the new usb serial connection and what do I have to do to achieve a device opening on the PC, not using getty on …

hi ( armbian stretch over orangepiPC ) i try to use OPI 5MP Camera OV5640 - Auto zoom with wide-angle lens for Orange Pi PC /Pi One/PC Plus/Plus2e However , video0 device doesnt appear on /dev/ folder. what can i do ? thanks

Hi, I followed the following link to create encrypted root. However, every time I boot, i don't see any prompt for password. My armbianEnv.txt is following", but nothing display at "Console" (HDMI) or "Serial" (debug 3 pins next to USB port). ~ Has anyone had any success? I did this for OrangePi Lite 2 (64-bit) H6 and no issue. Thanks

During the last days the system crashed twice - by crashed I mean that no SSH or other connections was possible and I had to force-power off. I used it for months without crashes before so its probably related to a new SATA drive. I wanted to look at the syslog and I noticed that /var/log/syslog only shows entries starting from the current boot and the /var/log.hdd/syslog is empty. Do I understand correctly that armbian logs only to /var/log which is a ram drive so the logs (or at least the syslog) is never persisted? How can I find out whether the SATA drive is responsible and why? Maybe it has a too high power consumption under special circumstan…

Hi, I've had a PcDuino3 for some time now, but I have barely used it because linksprite work was shoddy; so I never bothered to give the pcduino much time. I Also own a banana pi (A20), an O-DROID XU-4, several rPi's and an Orange Pi PC. All non rPi's are running armbian; you are all awesome for your work! I think I understand this problem with 4.x has something to do with the device tree .dtb files, but no clue what to do to get it to boot and display through HDMI. I'm actually wanting to use it as a headless server, but initial setup requires me to see the screen only because the onboard wifi is not working either (despite manually editing /etc/wpa_supplicant/wp…

Hi All, I used armbian for a few month and it works pretty good for me. Everything start going bad since I update it with RAID 1.1 board. Current system: Cubietruck + RAID board + Armbian (actual Ubuntu Xenial next) The issue is that board do not want to accept HDDs without reformatting them in a first row, ok, I made a full backup and after new installation from SD to the RAID just restore it --> It does not boot up even if I change fstab and armbianenv.txt in a boot section. I change /boot/armbianenv.txt (or how it called) parameter UUID to SD card back and could boot again, but system is on SD card. I perform…

Hello, I have a main WinTV dualHD http://www.hauppauge.de/site/products/data_dualhd.html, unt wanted this under Debian Stretch with the image from here https://www.armbian.com/cubietruck/ Mainlaine Kernel, use, according to this page https://git.linuxtv.org/media_tree.git/commit/drivers/media/usb/em28xx?id=11a2a949d05e9d2d9823f0c45fa476743d9e462b or even this https://www.mail-archive.com/ linux-media@vger.kernel.org/msg113120.html this should work ha. However, when I plug in the stick, I get this message: dmesg https://pastebin.com/mtyLnARP I also tried this here https://wiki.ubuntuusers.de/v4l-dvb/ but also without success dmesg | grep -i dvb [25.680224…

I try connect 3.5' LCD screen, but i have error ---------------------------- Jan 4 12:24:38 pls-home kernel: [ 54.977794] fbtft: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.981924] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.982417] fbtft_device: unknown parameter 'gpios' ignored Jan 4 12:24:38 pls-home kernel: [ 54.982696] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 Jan 4 12:24:38 pls-home kernel: [ 54.982947] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 …

Hi, I try to install Armbian Bulleye on my Nanopi Neo Plus 2. Well it completed the install, but when it reboot, I keep getting kernel panic. I try installing with the official Friendly Arm image (kernel 4.14 though) and it was fine (both on SD card and EMMC). Below is the serial console dump, also it seems to crash in random places too. Any help will be greatly appreciated. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.12.09 21:53:09 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2022.07-armbian (Nov 30 2022 - 10:43:13 +0000) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(debug):af220ebb-dirty NOTICE: BL31: Built : 10:4…

I built the newest image Armbian_5.24_Orangepiplus_Debian_jessie_3.4.113_desktop.img to work with my opi+2 board. I need 1280x1024 resolution and it works perfectly. However wifi connection keep asking password, but it worked well with Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112_desktop.img. It's weird that wifi scanning worked well, just failed to connect. How do I fixed this problem? thx

I'm trying to use an OrangePi Zero as an Alexa device, using github.com/alexa-pi/AlexaPi. This is headless, but I need analogue out and in. Given that it's headless, I thought I'd use the mainline kernel instead of headless. Everything installs fine, but ALSA does not see anysound card hardware. aplay: device_list:268: no soundcards found... I can try legacy, but I'd prefer to use mainline if possible.

Hi all, Recently i bought a orange pi +2E . I want to display it on a 2K display. with specs 2560x1440 resolution. https://www.alibaba.com/product-detail/New-5-5-LS055R1SX04-2K-1440_60694188895.html?spm=a2700.7724838.2017115.428.5a541062gAX23i I bought this board as it supports resolution upto 4K. But i failed to interface it with 2K. I m using armbian OS. I tried most of the modes in h3disp. Can anyone help me please . Thanks in advance

Is there a plan for supporting the "NanoPi Duo2" from"friendlyarm" in the future? http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2

Orange Pi Zero Plus2 H5 I currently am booting from the onboard 8GB EMMC. As I am still experimenting with this board, sometimes I would like to wipe and start from a backup remotely, keeping a copy of my backup on an SD card that's in the machine used for extra storage space. I use timeshift on my Mint laptop that restores a snapshot of / from an SDcard, but it is a graphical utility. Is there a similar CLI utility for Armbian? Or one that can be installed? Thanks.

hi can somebody fix repostiory install list error for chromium as chrome-commen and chromedriver wont install problem: chromium/noble 9:126.0.6478.182-1~deb12u1+narmbian1 arm64 web browser installs with version therefore chromium-common and chromium-driver,will not install because its looking for dependency chromium 126.0.6478.182-1~deb12u1+n1 Without the ":9" i presume he following packages have unmet dependencies: chromium-driver : Depends: chromium (= 126.0.6478.182-1~deb12u1+n) E: Unable to correct problems, you have held broken packages. please can somebody fix

Hi, I am running headless mainline jessie image on my cubietruck smoothly for some months now. The only drawback is that i need from time to time to play some videos on the tv. I have been waiting for hardware video acceleration in order to install mpv and play videos without GUI. I have been looking at the sunxi mainline effort and I see that for kernel 4.8 they plan the display engine clocks (TCON, FE, DE). As I am not a developer, it is not obvious to me (I have already googled it but no luck) if the display engine clocks are what we are waiting for hardware video acceleration on the mainline kernel. Can someone please explain (this noob question) what are displa…

Hello folks, I'm having trouble booting to Armbian. The green LED turns on, and the LAN lights work, but outputting to HDMI always ends in no signal. I have tried: - Using official Orange Pi operating systems, they work, but are unstable. - Using f3 to check if my SD card is corrupted/fake. Returns working. - Using different power bricks, will still turn on leds, but not output to HDMI - Using different Armbian kernels, no success Any ideas lads?

Hi, yesterday I moved my root partition to a 128GB SSD by running "nand-sata-install" Everything works fine. Now I got a SD-Card in my Banana Pi with one big partition: fdisk -l Disk /dev/sda: 128.0 GB, 128035676160 bytes 30 heads, 63 sectors/track, 132312 cylinders, total 250069680 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93d6d043 Device Boot Start End Blocks Id System /dev/sda1 2048 250069679 125033816 83 Linux Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 46 heads, 9 sectors/track, 18706 …

hi all i have an orange-pi zero that boots from network. the kernel and some other files are loaded over TFTP and the root path is mounted by NFS and every thing works fine. also i have a 3.5 inches LCD that works with fbtft_device module. the problem is when the board boots over network, the LCD dose not initialize completely but when i boot the board by SD card the LCD init's 100% fine. there are no error in dmesg but the LCD is 1/3 black and 2/3 white. dmesg: [ 51.270008] fbtft_device: SPI devices registered: [ 51.270303] fbtft_device: spidev spi0.0 33000kHz 8 bits mode=0x00 [ 51.270362] fbtft_device: spidev spi1.0 33000kHz 8 bits mo…

I have OPI 2 running latest armbian mainline with MQTT broker and home assistant only. And I've started to experience hard freezes that only power re-plug helps :/ At first I thought that only networking was gone, but I've triggered hearbeat on red onboard led and this led is just stopping blinking on freezes. I've even got rid of Network Manager and setup iface in old good way via /etc/networking/interfaces. Then I've connected to serial console, run minicom in screen with logging to file. Just to see if serial console would show some kernel panic or so...but nothing, no output on serial console. Anyone experienced such behaviour? How to debug it? My sec…

I have installed ~$ uname -a Linux orangepioneplus 5.4.18-sunxi64 #trunk.038 aplay -l **** List of PLAYBACK Hardware Devices **** card 0: allwinnerhdmi [allwinner-hdmi], device 0: 5091000.i2s-i2s-hifi i2s-hifi-0 [5091000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Device [USB PnP Sound Device], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1 works good alsamixer When choosing allwinner-hdmi

For some reason, the CPU frequency in Ubuntu is set to 1416000 while the hardware can reach 1512000, which is an improvement of about 6 and a half in CPU performance. I would appreciate a change or explanation. Thank you very much for everything.

Hello everybody, I can't run OpenGL ES on my OPI One's. I tried with a fresh new install distro : Armbian 5.13 (Armbian_5.13_Orangepione_Debian_jessie_3.4.112_desktop) with an HDMI-to-DVI screen ( h3disp -m 720p60 -d) This is what I've got : Any idea ? Does someone have the same issue ? Thanks all.

So I'm pretty new at using serial ports in linux so not even sure if this is the right place. I'm playing around with MIDI using the serial ports on the Orange PiLite - it uses the baud rate of 31250 to achieve this you use setserial to get the base_baud (which it reports as 1500000) and you divide by the speed you want to get the divisor i.e. 1500000/31250 = 48 this becomes >setserial /dev/ttyS1 divisor 48 speed_cust So now when you use 38400 as your baud speed it actually becomes 31250.... ...in theory after some fiddling I found the divsor is actually 50 as 48 gives you weird results which would suggest that the base_baud is actually 1562…

Hello, I would like instructions to install the mali 400 drivers for my orange pi pc +, I tried to install but I did not succeed, could help me?

Hello, guys! I'm trying to make use of gpio-poweroff procedure. I'm trying to understand the consequences of the approach I've used. Here's what I did 1) Added power_ctrl: power_ctrl { compatible = "gpio-poweroff"; gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; force; }; to arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts 2) Recompiled the device tree blob and put it where it belongs The gpio-poweroff's code got probed but failed due to `pm_poweroff_handler` being set to something. So I figured it out that it's set to `psci_sys_poweroff` in [drivers/firmware/psci.c](https://github…

Hi, i have a small/big problem because i`m not able to change the system time. The same with ntpdate, its not able to adjust :( and i didnt have any idea whats wrong. My cubie3 runs with Debian Jessi. Here are some logs what i tried to adjust my time. Can anybody see whats wrong and what can i do? You see, a "date -s" has no result in adjusting system time root@www:~# date -s "15 MAY 2018 09:47:00" Di 15. Mai 09:47:00 CEST 2018 root@www:~# date;hwclock Di 15. Mai 10:22:58 CEST 2018 Di 15 Mai 2018 10:02:04 CEST -1.711357 seconds same, to success with timedatectl root@www:~# timedatectl Warning: Ignoring the TZ variable. Readi…

Hi, I'm trying to create a DT overlay for my Cubietruck running 4.19.62 and I've placed it in /boot/overlay-user and changed the user_overlays entry in boot.scr to load it. It is being loaded but I'm getting FDT_ERR_NOTFOUND when trying to apply it. The overlay is meant to change the label and default-trigger entries for the four LEDs in the leds node. I'm using dtc 4.1.4 and it does compile this overlay. Can anybody tell me how I can change this overlay so it will work ? Or perhaps tell me if this is not possible. /dts-v1/; /plugin/; / { compatible = "allwinner,sun7i-a20"; fragment@0 { target = <&leds>; …

hi! I update kernel for cubie a10, bud do not know how tu update boot loader. As i know boot loader used uboot. In 1st part of microsd i have files drwxr-xr-x 3 root root 1024 Jun 18 2015 . drwxr-xr-x 5 root root 4096 Jun 12 2014 .. -rw-r--r-- 1 root root 12288 Jun 18 2015 .uEnv.txt.swp drwx------ 2 root root 12288 Nov 17 2014 lost+found -rw-r--r-- 1 root root 44240 Nov 17 2014 script.bin -rw-r--r-- 1 root root 215 Jun 18 2015 uEnv.txt -rw-r--r-- 1 root root 6544616 Nov 17 2014 uImage As i understand i need change uImage file. Ok. I goint in /boot And export VERSION=4.3.3 mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -…

hy all! i need little help.... i have one orange pi plus2e and try make wireless access point... OS: armbian 5.23 Net connection: PPPOE 200/100Mbit (username/password) i read several topik about in this theme. try many settings... ap option not work my plan: I would like to do wifi access point with NAT,Firewall,DoS protection,UPnP,PortForward,IP/MAC filter function...automatic reconnection,WPA2 wifi protection i very amateure in this theme. I really prefer it if I did OpenWRT,But reading support.not available. I very big thanks help...

Hi all. i say goodby rental server , hello orange pi . by the way i run nginx as basic authentification . /etc/nginx/nginx.conf is ------------------------------- events { worker_connections 800; } http { include mime.types; default_type application/octet-stream; index index.html index.htm; keepalive_timeout 65; server_tokens off; server { listen 80; server_name localhost; #<-for test root /var/www/d1; } server { listen 80; server_name n------------a.dip.jp; root /var/www/d0; } server { listen …

Hello Folks, sorry for popping up here with a technical problem first thing - but I have some trouble. I have a circuit where an attenuator is connected to PA19. Sadly, the port seems to have a pull up which stays active even when I use wiringPi to set the port to input - in fact, even if I short the pin to low via my Keithley ammeter, it still shows up as high. Re things which I already tried: I tried to reduce the fex file to look like this: [product] version = "100" machine = "orangepi-lite" [platform] debug_mode = 1 eraseflag = 1 next_work = 2 [target] boot_clock = 1008 storage_type = -1 [key_detect_en] keyen_flag = 0 [fel_key] fel_key_max = 7 fel_key_m…

I have changed to 1080p and its almost stable but pull up any window that has maybe moderate workload to say heavy such a chromium the screen starts bouncing around. Think you know what I mean by bouncy, stuttery flashy. I thought that would just be fbturbo drivers and just the fex script but nope and a bit stuck. There is an image for Xenial as using the legacy version on the OrangePi site that is rock solid @ 1080p so it must be fixable but not sure what. Jan 2019 of xenial. I ran into some permission errors with NodeJS & PM2 so thought I would give Armbian another go as first image I tried was the latest less stable Bionic/Stretch which also at 1080p are …

Hello, I have an OrangePi Zero H2 which until recently was running almost flawlessly with the Armbian_5.38_Debian_stretch_4_14_14 image. When I did a kernel upgrade using "apt-get dist-upgrade" (because I had earlier the error message ~"failed to Load Kernel Modules", and dist-upgrade was recommended), and this dist-upgrade failed inbetween (probably because of power consumption), the SD card was left in unbootable state. (error msg see below [1]) I concluded that the /boot directory was corrupted, so from a new installation of Armbian_5.38_Debian_stretch_4_14_14 made elsewhere I copied all the /boot directory over to my SD card. This m…

armbianmonitor -u hastebin - yadagozohu (armbian.com) Using https://redirect.armbian.com/region/NA/orangepipc/Jammy_current image Attached is the output from the serial console for uboot etc. The console is using about half the vertical resolution, and a little under half the horizontal resolution of the HDMI monitor. In contrast, the orangepi.org built image is using the full resolution. Image: Orange Pi PC 2.0.8 based on Debian Buster Kernel: root@orangepipc:~# uname -a Linux orangepipc 5.4.65-sunxi #2.0.8 SMP Mon Oct 26 10:20:38 CST 2020 armv7l GNU/Linux In Armbian, I've tried using …

Hi armbians, I was wondering how do you trigger the red LED for other devices like USB r/w or wifi tx/rx . echo mmc0 > /sys/class/leds/orangepi:red:status/trigger works like a charm for microSD r/w. I want to trigger it for my wifi interface which is "wlx0013ef6d5c23" . Any thoughts? Detailed log uploaded at http://sprunge.us/gCjP

Hi everybody, I asked to forum in the past about game library for C but it is very hard to develop our software in C. As I told in the past, I don't develop a game, I using it to draw some graphs in 2d or 3d. I am here again to ask that, Is OPI Zero can run a game software from Monogame framework. We can port our windows C# software which is written with XNA framework to Linux enviorment with MonoGame. Thanks

Hi! I've been using Armbian on my a20 olinuxino lime2 board without issues for over a year now. Yesterday i decided to reflash the installation image onto the SD board. I've tried to flash it to different SD cards using the same method (SD card formatter + etcher), all of them booted but the SSH server always refuses the connection. Are there any workarounds to this?

Hello few day ago I install one again ARMBIAN in my OPI WIN PLUS this version https://dl.armbian.com/_old/orangepiwin/archive/Armbian_19.11.4_Orangepiwin_bionic_current_5.3.13_desktop.img.gz When I was typing armbian-config The loading config setting was missing sudo apt-get install armbian-config and after install. when I login via putty I see screen like below before that I don`t have any main screen Could You advice what`s heppen (when I was first install those image (.5.3.13_desktop.img.gz) I`m remember the OPI WIN screen.

Hello, on a Banana Pro, is there a way to disable on board wifi? I am using Armbian Buster. Thank you, Alex.

I haven't solved the problem of spdif-out on mainline kernel. But, on legacy kernel 3.4.112, spdif-out works. but, has a limitation upt 48khz? doesn't work of 88khz, 96khz, 176khz on my Nanopi Neo Air 1.0. Is it correct to have a limitation. Thanks in advance.

Hello community.. I strugling with hardware acceleration on Orange PI +2E. I read all forums and used google..but all what I found are old threads. I would like to know where can I find some tutorials how to install drivers for HW encoding in h264. Compilation of ffmpeg is not a problem, I did it and tried to encode 720x576 mpeg2 live stream to h264 @ 1000kbps with fdk-aac, and it works but..all cores are around 70%, and it sometimes starting the buffering when I watching on for example on POT player or Vlc. I would like to achive two thing: 1) to be able to use hw acceleration to encode h264 from mpeg2 stream. 2) to be able to use hw de…

I was curious to see how Mainline kernel performs on GbE test against a Legacy kernel. For the Armbian side i chose the nightly dev Armbian_5.27.170602_Orangepiwin_Ubuntu_xenial_dev_4.11.1_desktop.img (Desktop) and for the Legacy i chose my own build with all "Bells and whistles" (full Desktop, hdmi, camera, bt and wifi). I did not optimized Armbian Mainline, just installed and run stock. For the Legacy i optimized as usual. If there is some optimization to do on Mainline side, i missed. I have some observations about the board and results: * Board is without Heat-sink, * Legacy subsequent test got lower values, i suspect it runs h…

Hi, I was wondering if anyone had been able to get this working ? And, yes i know that OPI-Win is WIP/testing. I read some stuff here & on the linux-sunxi irc log that seemed to say that it should work & I've tried the following without luck. I was wondering if someone with alittle more knowledge about this may be able to help or point me in the right direction. I also tried to compile u-boot v2017-09 but it fails with a sdram too big error I tried to backport some of the config to 2017-07 but that'll take time i expect ... /boot/armbianEnv.txt (many combinations of this) disp_mode=720p60 disp_dvi_compat…

I'm working on Orange-pi zero (H2 +)board. Sometimes , after rebooting of system , I Noticed that MAC address is changed. From where It is reading MAC Address?? any help on that?

Hi, I have the following problem when a extern USB disk is connected the Banana Pi won’t boot., if I unplug the USB disk the Banana PI boots from the SATA disk fine. I’m using debian jessie and use the nand-sata-install to boot from SATA disk Kind regards,

orange pi one armbian xenial When I obtained the orange pi one I installed armbian xenial. I booted the orange pi one. During boot I cannot recall if a red light flashed next to a steady green flash. The desktop worked. The orange pi one was connected to a hdmi display. Resolution 1280 x 720. I wanted to use a 1024 x 768 vga display by hdmi vga converter. The desktop would keep the 1280 x 720 resolution when displaying the desktop. I tried different things in order to get a 1024 x768 resolution. Did not work. One configuration resulted in trashing the power supply. I connected another power supply. The power suppl…

Hi I want make VPU work on OPI 3 with mainline kernel I apply the LibreELEC Kernel patch and /dev/video0 is registry. I also apply LibreELEC FFMPEG Patch and build with v4l2-request But when I decode videos,VLC did't decode frames and kernel say's : cedrus 1c0e000.video-codec: Missing required codec control Why? What should I do?

Hello First of all, thank you for the great effort of the Armbian project. In second place: I have a NanoPi Duo device, which has been working fine with an old version of Armbian. But when trying to use the latest version, it happens that the serial port console continuously gives the following message and does not allow login ... ... [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Started Network Manager Script Dispatcher Service. nanopiduo login: root (automatic login) Authentication failure nanopiduo login: root (automatic login) Authentication failure n…

Hi, Is there any testing utility/exerciser for OPi PCPlus eMMC? I'm geting strange problems when fast and large writes happen in eMMC. /Edit this is what I get by running 'armbianmonitor -c ~/healthtest' WARNING: It seems you're not testing the SD card but instead healthtest () Starting to fill healthtest with test patterns, please be patient this might take a very long time Free space: 3.59 GB Creating file 1.h2w ... OK! Creating file 2.h2w ... OK! Creating file 3.h2w ... OK! Creating file 4.h2w ... OK! Free space: 369.04 MB Average writing speed: 6.95 MB/s Now verifying the written data: SECTORS ok/corrupted/changed/overwrit…

Hello, i want to use my Cubietruck with an Portmultiplier. So, i want to add this Kernel-Parameter: How can i do this. Spider.Mann

Hey, I've got an Orange Pi Zero Plus 2 (H3) with Armbian 5.41 and mainline 4.14.18 with Debian Stretch. If I try to run X11 with: sudo startx I get the following error: X.Org X Server 1.19.2 Release Date: 2017-03-02 X Protocol Version 11, Revision 0 Build Operating System: Linux 4.9.0-4-armmp-lpae armv7l Debian Current Operating System: Linux orangepizeroplus2 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l Kernel command line: root=UUID=bab2d356-e17e-4857-836a-5fc44cbf541f rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=451adc…

Hello I am a new user of the armbian software. I installed the latest version of vanilla to armbian in the description of the material, I saw that the buscan was activated. I have a banana pi pro, I would like to know how to install the software for CAN bus. I read that can4linux was the driver to install. I read on this forum they've installed patches, but how do I installed a patch? Thank you for your help. PS: I speak French and I use a translator.

After upgrade to latest kernel (4.19.38) my device only boots into maintenance mode. System is on emmc and no problems before. I started armbian-config and switched back to previous kernel, but it doesn't boot system. Even with all USB devices disconnected it didn't start (as i see there are some usb errors in log), file system seems to be clean, just didn't start system in normal mode.... Any advice? Thx Update: OK, solved, after installing latest updates within maintenance mode its ok again....

hello please help to install and configure wifi usb edup ep n8553 on OPI pc dongle unrecognised and no working drivers. riz

hi, I'd like to ask regarding the behavior of eht: I want to use eth wire connection as primary ISP connection and wireless connection (using wifi dongle, different network) as backup ISP connection. But when I disconnect the cable physically, the eth0.101 subinterface is sill up, keeping it's IP address. Here's the config: cat /etc/network/interfaces # In real world, this is used on the same situations of auto but the difference is that it will wait an event like "plug the cable" on ethernet interfaces. allow-hotplug eth0 . . . # receive IP-Address from your DSL- or cablemodem auto eth0.101 # Replace "dhcp" with "manual" in the next line, if you are g…

I recently switched from a Raspberry Pi 2 running Arch Linux to a Banana Pi (the original) running Armbian for music streaming using MPD. My output device is an XMOS-based Gustard U12 asynchronous USB transport feeding my DAC via AES/EBU. Using Armbian on the Banana Pi, all my 24-bit/192kHz music is being played back as 24/96, according to the display on the transport and DAC. All other sample rates (44.1, 88.2 etc.) are being played back in their native sample rates, as expected. Is ALSA on Armbian system-wide limited to 96 kHz? I have never had an issue like this before, and I don't know where to begin in regards to troubleshooting. I'm guessing th…

Hi, Can anyone share a version of nightly build for Orange Pi Zero Debian Jessie with kernel 4.11.12 or newest for testing? I don't have the possibility to build own version of Armbian but I can try and tests existing distributions armbian. At current, I have use armbian Debian Jessie with kernel 4.11.5 Regards

I want to control a fan via a script. I found a bunch of tutorials for pwm, but they were either for older version of Armbian, or for another board. I could not find a tutorial for Allwinner H6 boards. Apparently simple overlays=pwm doesn't work anymore. Anyone have any pointers as to how to go about it? my goal is to do something like $ ./setfan.sh 50 Setting Fan Duty Cycle to 50%... Nothing more complicated. I have a 5V fan for the system and I just want to tune how fast it should run - now it's going full 100% and it's louder than I'd like. I planned to do this with a trimmer but because the world situation and distances, the trimmer…

Hello, i am new here and need the line in from MCU audio codec(U1-3 Pin AB20 & AB21), located wired on CSI connector(CON1 Pin 1 & 2), active. Is it possible? Regards Mario

i use armbian on my cubieboard2(based on Allwinner A20 Chip) with default HDMI. i have some problems. the first is default font of Terminal emulator and XTERM is so small. how can i changed their font size ?????!!! the second is i cant edit/create network connection with network manager. the ipv4 nad . .. are disable. is there anyone to help me plz.????

first off: I'm totally new in the Linux world, but it's really fun to play with *Pis! currently I'm on a OPILite but I have some RasPis lying around and just ordered a nanoPieNEO2. I'm trying to setup a filesystem that supports deduplication, as far as I can tell that's ZFS or BTRFS. After a lot of reading and learning I got BTRFS with bedup running, but bedup is only file-wise deduplication. The solution for block-wise would be duperemove, but I can't find/get/install/build it for armhf. Has somebody tried block-wise deduplication before and can point me in the right direction? I'm running armbian 5.31 on 4.11.5

The system displays two WLANs, but in reality, there is only one onboard wireless network card. The network connection is slow and disconnected. The official system of Orangepi is normal, this issue occur in the new version of the Armbian system. logs：https://paste.armbian.com/eborebaviq

I posted this in the Orange Pi Zero 3 topic earlier but got not response. **How would one go about to get the default u-boot config that is flashed to spi to have netretry turned on?** > If anyone is interested, here is a guide to netboot (pxe) the orange pi zero 3: https://raymii.org/s/tutorials/Netboot_PXE_Armbian_on_an_Orange_Pi_Zero_3_from_SPI_with_NFS_root_filesystem.html

Hello! Faced the problem that in new versions of the system does not work sound! in the / dev / snd / folder is empty. Who faced this problem how to solve it?

Hello: I have an issue with one of my opi pc boards: When I connect it to hdmi tv and tv is not connected (switched on before booting the soc), I get just a red screen. Armbian is up and ready. I can log through ssh. Tested in Armbian_5.38_orangepipc_Ubuntu_xenial_default_3.4.113_desktop and openelec (last version). Same problem in both. I'm looking for mods in the .fex file (if there are any that applies to this case). So far I checked http://sunxi.org/Fex_Guide without luck. Time ago, I had a similar problem with an raspberry pi. In this case it was solved with a parameter in the config.txt (hdmi_force_hotplug=1). With thi…

Dear all, I discovered that the leds section is missing in the devicetree of orangepizeroplus2 H5 (at least upto kernel 4.14.39), and had to write an overlay to get them to work. The overlay has been attached. I've added this overlay file to /boot/overlay-user/ and added the overlay in /boot/armbianEnv.txt as follows: Kind regards, Dennis sun50i-h5-orangepi-zeroplus-leds.dts

I want my armbian (running on OrangePi lite) to output 2560x1440p60 resolution. the h3disp tool has an option for 2048x1536 (3:4) but not for 1440p. How can I get 1440p output?

Just a FYI Previously using nmtui-connect and adding a Wifi Config would survive across reboots. With nightly: Armbian_5.26.170226_Orangepipcplus_Ubuntu_xenial_dev_4.10.0 I find that I must repeatedly use nmtui-connect and even then it creates additional NM connection profiles # nmcli c NAME UUID TYPE DEVICE MyWifi 60caede4-0d67-4e72-9696-6e9f76f9ec0a 802-11-wireless -- MyWifi 1 a4f778ff-e8b9-431c-ad70-98d3e32252bc 802-11-wireless -- No other OS mods (such as /etc/network/interfaces) were made After nand-sata-install only nmtui-connect was utilized

Hi everyone! I wonder if modifying the "fbdev" driver to use Mali GPU to improve gaming performance is possible. I enabled `gpu` dtb, but according to "glxinfo -B" it uses "Device: llvmpipe, Accelerated: no". I'm curious if this can be improved somehow. BTW I found this old commit for Odroid C2: link

Hi folks, I tried to run jdownloader on orange pi pc under armbian 5.25 but it was not successful, i noticed that java uses more than 100% of cpu, is it normal ? Best regards. Adel.

Hello again, I downloaded the latest Orange Pi Win Ubuntu server – legacy kernel and installed it. It works fine, but when I connect from my win10 notebook via ssh with “putty” or “Windows power shell” the connections stops after the input of the right password. If the Password is wrong i have to re type it. Service ssh status: pam_unix(sshd:sessions): session opened for user root (uid=0) So it looks like the ssh on my “OPI win” works, but on putty I have only a blinking cursor. When I connect ssh via my android phone it works, without problems. Had anyone ells this problem? greeting…

I got a non-booting BPiM2+ after running `apt dist-upgrade`. I started with a fresh installation using the `Armbian_20.05.2_Bananapim2plus_focal_current_5.4.43_desktop.img` image. After log in I get from dpkg: ii linux-image-current-sunxi 20.05.2 armhf Linux kernel, version 5.4.43-sunxi ii armbian-firmware 20.05.2 all Linux firmware Then I updated the system via apt dist-upgrade and now I have ii linux-image-current-sunxi 20.05.3 armhf Linux kernel, version 5…

Hello, I hope someone might help me on this. Is anyone here using the ENC28J60 Ethernet port on an Orange Pi Zero 2W or Orange Pi Zero 3? If so, can you please share the file .dts (or .dtbo) that is working for you? I've generated a .dtbo using the file in https://github.com/armbian/sunxi-DT-overlays/blob/master/examples/spi-enc28j60.dts, with: dtc -I dts -O dtb -o /boot/overlay-user/spi-enc28j60.dtbo spi-enc28j60.dts but still it doesn't work. It says "chip not found". I'm using the same cable pinout as in my Raspberry Pi Zero 2W and it works successfully, but not in the Orange Pi Zero 2W. Any idea?

Hello everybody! I'm trying to make a carPC based on Armbian (5.25 Bananapi Ubuntu xenial default 3.4.113 desktop) and a banana pi, almost everything works except for sound in navigation. root@bananapi:~/7ways# ./7ways root@bananapi:~/7ways# ALSA lib pulse.c:243:(pulse_connect) PulseAudio: Unable to connect: Connection refused root@bananapi:~/7ways# ALSA lib pulse.c:243:(pulse_connect) PulseAudio: Unable to connect: Connection refused root@bananapi:~/7ways# ALSA lib pcm_dmix.c:968:(snd_pcm_dmix_open) The dmix plugin supports only playback stream root@bananapi:~/7ways# ALSA lib pcm_dsnoop.c:545:(snd_pcm_dsnoop_open) The dsnoop plugin supports only capture stream root@b…

I first noticed this on my Orange Pi Zero. The latest Armbian releases (4.13.x) have some kind of gap between bytes when transmitting over SPI. I have an SPI performance test built into my SPI_LCD code: https://github.com/bitbank2/SPI_LCD If you run the demo program, it measures how many frames per second it can write to an SPI-connected LCD. On older Armbian builds with kernel version 3.x, it would usually get 27-33FPS on the H2/H3 boards. With the mainline kernel builds and running the same code, I'm seeing 9-17FPS (depending on the board). The H5 doesn't seem to be affected (I'm using an Orange Pi Zero +2 H5 for testing also). Anyone else seeing…

Problem was, that via same file /etc/rc.local was started dnsmasq which crashed and rc-local.service didn't continue with starting wvdial , Hello All, Could someone please help me to start command wvdial during booting-process? When I star wvdial command from command line, LTE USB modem is started and ppp0 interface is activated and everything works fine, but I want it to be started automatically during booting-process. I tried add wvdial to end of file /etc/rc.local, but wasn't successful. I also tried to add record to file /etc/network/interfaces as: auto ppp0 iface ppp0 inet wvdial None of these mentioned above helped.…

When i first tried out my orange pi prime in october 2020 i thought i recalled that the wifi worked. With a current armbian image, the wifi can't authenticate. I tried several of the available kernel images. I'm sure that the wpa2 password is correct because I control the router and other devices connect all the time. If i plug in an ath9x usb wifi dongle, that is able to connect, so it would appear to be an issue with the onboard rtl8723bs driver.

I noticed that the Nano Pi Neo has a pin or 2 labeled 3.3V out. How much current is available from this source? I have a CODEC and a few other things that need 3.3V power. I need to know what the 3.3V output can deliver safely, or if I should just add my own 3.3 regulator for the external circuitry.

Hello, I am still using my cubieboard1 for openhab2. A few days ago I installed the system on an USB stick, then I thought that the 32Gb SD card is the for nothing. And I am planing to replace the 32GB sd card with a 128MB sd card. but i am stuck in prepairing the smaller SD card. Could somene advice me how to do this change? Until now I just formated the small sd card into ext4 and copied the /boot from larger sd card, but didn"t booted. Help is much appreciated.

Greetings. For anyone interested FriendlyArm have a Github repo which contains a working AW CSI driver. and has device tree files for NanoPi M1+ and Neo Air. See https://github.com/friendlyarm/linux.git. The branch is sunxi-4.16.y This is a work in progress but the setup is vastly simplified compared to the VFE subsystem in the 3.4/3.10 kernels. The OV5640 driver does produce video but I'm getting some odd images at the moment. Possibly colorspace related. As a bonus USB OTG is also working ... fa@FriendlyELEC:~/src$ v4l2-compliance Driver Info: Driver name : sun6i-video Card type : sun6i-csi Bus i[593…

I met a problem that kernel showed allwiner H6 ethernet internal error. link: It is hard to loacate what makes that error occur, I wish that kernel can show my log added to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c. my work below: 1 Added printk to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c, and made patch with git format-patch, move patch to userpatchs/kernel/sunxi-next. 2 run ./compile.sh to compile armbian, I am sure that patch work, have checked drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c after compile.sh completion 3 burn Armbian_5.71_Orangepioneplus_Ubuntu_bionic_next_4.19.13_desktop.img to sdca…

Hello all, If i detach battery all works ok. With attached battery system reboots instead of shutting down. Anyone experiencing this issue again with 5.4.21 kernel? Is there a workaround to solve it, maybe in u-boot or somewhere else? Armbian 20.05.0-trunk built from source Thank you

I recently bought an Orange Pi Lite and installed Armbian on it. Everything works fine except I can't write to USB drive. I'm not logged in as root. USB mounts automatically but other users can't seem to write to it. I searched this issue on the internet but could not figure out how to change permission as this is the first time I'm using a Linux machine. Any help would be greatly appreciated. Below is what I see when I open up USB properties. Thank you.

Anyone with a full functionging Retro OrangePi on OPI PC using just analog out(NO HDMI)? Need to know what I'm missing. EMU Analog - Video = working Analog - Audio = working Controller = working GAME Analog - Video = working Analog - Audio = NOT working Controller = partial working Once game start, no sound until exit.