Other families

When cubox is configured to run wifi, it takes 60+ seconds for it to start up with no network cable plugged in. Where as when I plug in a network cable to the network port it will start up under 10 seconds. Hardware: Cubox-i4 Pro Running Ubuntu Trusty image found here: http://www.armbian.com/cubox-i/ Any advice would be appreciated.

Hi, I'm trying to use desktop community build for Windows dev kit 2023 but it is not working. Current image: Armbian_community_24.8.0-trunk.554_Wdk2023_noble_wdk2023_6.7.0-rc6_gnome_desktop.img.xz When using etcher to flash to usb, it will flash but fail at validation step say "Cannot validate, the image could be corrupt" or something like that. If still use that usb in WDK, it won't boot. The lite version Armbian_community_24.8.0-trunk.554_Wdk2023_bookworm_wdk2023_6.7.0-rc6_minimal.img.xz is still working fine.

Hello, I have a brand new cubox-i4x4 and am attempting to install Armbian Stretch mainline kernel 4.15.y I downloaded the image from https://dl.armbian.com/cubox-i/Debian_stretch_next.7z used keka and etch to extract and write image to the SD card. After installing the SD card in the cubox and powering on, it gets stuck at: U-Boot SPL 2017.11-armbian (Jan 24 2018 - 22:39:16) Trying to boot from MMC1 U-Boot 2017.11-armbian (Jan 24 2018 - 22:39:16 +0100) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 24C Reset cause: POR Board: MX6 Cubox-i DRAM: …

Hello I have a nanoPc t3 plus board and I cannot boot it. I searched and I found a related topic that has the same problem but there is no answer. I believe the problem is because of different mem chip but the same revision (1709) Can boot armbian whit compiled friendlyArm Uboot? topic URL my memory chip picture and logs (from the topic) \

How to Reset armbian 24.5.1 jammy, the device long time I not power on, but just now I power on can't log with ID Root & Password 1234. already many things still can't resolve it. If have any suggestion please let me know.

Is there lvds screen compatible with humming board pro version on armbian and if not wich lvds 30pin will u recomend to modify or assist to work on the HB pro

Hi, I've been using my cubox-i 4x4 for close to one year and now after one reboot no hard drive connected to Esata port works. I tried with different debian isos and they work fine on the sd card and hard drives connected to usb ports too.... Any help?

Wheezy: deb http://repo.jm0.eu/BSP:/Cubox-i/Debian_Wheezy/ ./ Repository is online but installations is untested by me.

I am using your Debian (wheezy) on a SolidRun Hummingboard-i2eX. uname -a Linux cubox-i 3.14.14-cubox-i #2 SMP Mon Aug 31 19:36:11 CDT 2015 armv7l GNU/Linux In /dev, it looks like there are two IMX serial devices: ls -l /dev/ttymxc* crw-rw---T 1 root dialout 207, 16 Feb 4 2001 /dev/ttymxc0 crw-rw---T 1 root dialout 207, 19 Feb 4 2001 /dev/ttymxc3 I can send/receive data from /dev/ttymxc0 (uart1) by using pin 8 (Tx) and pin 10 (Rx) of the 26-pin header on the board. But how can I access /dev/ttymxc3 (uart4)? Is there a pin somewhere on the board that I can connect to so I that I can send serial input to uart4? Thank you.

Hello, I deployed the latest image "Armbian Buster mainline based kernel 5.8.y" and after initial setup, I cannot activate the analog sound card. What I did: The "Hardware" section in "Settings" section of armbian-config was missing, so I installed the following packages: "linux-dtb-current-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.9.5-sunxi, linux-dtb-dev-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.10.0-rc2-sunxi" and after that changed: /boot/armbianEnv.txt by adding overlay_prefix: "sun8i-h3". This was the only way I could make armbian-config to correctly display the "Hardware" device tree. I tried to put: i…

Hi, I have used ARMBIAN Debian GNU/Linux 8 (jessie) 3.14.79-cubox the upload speed was horrible about 2,5 Mbytes/s Now I switched the kernel to vanilla ARMBIAN Debian GNU/Linux 8 (jessie) 4.8.4-cubox the upload speed is now about 8,5 Mbytes/s On booth kernels the download speed is ok about 48 Mbytes/s root@tombase:~# ifconfig eth0 eth0 Link encap:Ethernet Hardware Adresse d0:63:b4:00:c4:04 inet Adresse:192.168.15.7 Bcast:192.168.15.255 Maske:255.255.255.0 inet6-Adresse: fe80::d263:b4ff:fe00:c404/64 Gültigkeitsbereich:Verbindung inet6-Adresse: 2003:84:ab4c:ac00:d263:b4ff:fe00:c404/64 Gültigkeitsbereich:Global …

Hi, I have Connected i.MX6 Single Board Computer. https://dl.dropboxusercontent.com/u/6943408/ConnectCore/DSCF0496.JPG I need to boot Debian-based system from SD card. I tried a lot of images - without success. Only original Yocto image from Digi.com company boot: ftp://ftp1.digi.com/support/digiembeddedyocto/2.0/r3/images/82003940_C/ccimx6sbc/x11/dey-image-qt-x11-ccimx6sbc-20160811150718.rootfs.sdcard http://www.digi.com/resources/documentation/Digidocs/90001945-13/task/yocto/t_faq_boot_from_usd_yocto.htm but I need Debian-based OS, not Yocto. From dozens of image for other board I have "success" only with http://www.armbian.com/donate/?f=Armbian_5.20…

Hi, I just tried last Debian iso from solidrun where bluetooth is working. It is the only issue I have with my Cubox-i 4x4 working with debian from armbian. But there is always a but..... I can't copy the system to the hard drive and make it work after reboot, only works from sd card. So my point is How can I use the benefits of armbian (it's tools) on another iso where drivers look work fine? thanks.

Hi every one, Im new on this form and this is my first time, when Im working with HummingBoard. On my HummingBoard is connected a little board with HDMI input and is connected with DVD Player. One another HDMI, which is on HummingBoard, is connected with Monitor, where I can see my console. So, my question is, how can I install, that my little board will become a video from DVD Player and streaming it to the HummingBoard, so, that I can see this video on my Monitor. Im using the Debian wheezy image Sorry for my english, hope for fast help

Dear Armbian Team, I have a BPI M64. all the images for BPI m64 have "Audio Codec" except the armbian image. so i cannot configure my 3.5 audio jack because it needs "Audio Codec" card in alsamixer. i cannot hear any sound from the jack because it needs to be configured with alsamixer over the "Audio Codec" card. there is only sun50i-a64-audio and sun9i-hmdi. but no "Audio Codec". can you give me any solution?

Hi there, I see `iw list` is showing that the i4 pro's internal chip supports AP mode. [1] However, when I try to run `/usr/sbin/hostapd /etc/hostapd.conf` it errors out with no driver entry or driver=nl80211 in hostapd.conf [2] Configuration file: /etc/hostapd.conf Failed to create interface mon.wlan0: -95 (Operation not supported) wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE wlan0: Could not connect to kernel driver Using interface wlan0 with hwaddr 40:2c:f4:ae:16:c6 and ssid "aa" Failed to set beacon parameters wlan0: Could not connect to kernel driver Interface initialization failed wlan0: interface state COUNTRY_UPDATE->DISABLED w…

Hi There ! Finally managed to Get the Cubox up& running well . Upgraded from Wheezy to Jessie . Still Stock 3.14.14 Kernel. Well, next step: The graphics card/hardware acceleration. Is there a quite straight "Do this,get that, then do that" howto to get it working ? Thanks so far! ###edit### Things are geting quite weirder today. Did a further SD-Card with Cubox-i_Debian_2.6_wheezy_3.14.14 to get GPU-Suppport by the Wheezy releases . corrected sources: deb http://repo.maltegrosse.de/BSP:/Cubox-i/Debian_Wheezy/ ./ deb-src http://repo.maltegrosse.de/BSP:/Cubox-i/Debian_Wheezy/ ./ apt-get update / upgrade Did apt-get install…

I installed "Armbian_5.25_Cubox-i_Ubuntu_xenial_default_3.14.79_desktop" because I am having many other troubles with "Armbian_5.25_Cubox-i_Ubuntu_xenial_next_4.9.7_desktop". Everything looks working fine until I noticed I can't use firefox over a RDP, in any user session. Also I would like to comment I can't make work chromium, getting all time a white page with a "Aw, Snap" message. Any idea about how to fix these two problems?

I've tried two releases of Armbian for the Jetson Nano and was struggling to get SPI enabled on the Jetson. To check if SPI is enabled, I've been reading its status is through: cat /proc/device-tree/spi@7000d400/status which just returns disabled Here's what I tried: - enabling spi-spidev through armbian-config, but this option doesn't exist in armbian-config as it does for other releases for devices - making a custom device tree dts file and pointing extlinux.conf to it (below is the relevant snippet): spi@7000d400 { compatible = "nvidia,tegra210-spi\0nvidia,tegra114-spi"; reg = <0x00 0x7000d400 0x00 0x200>; inte…

Hello Solidrun has updatet their microsoms to v1.5. MicroSOM rev 1.5 Wifi: 802.1 b/g/n - 2.4 / 5 Ghz, single or dual MIMO with Bluetooth V4.0 (TI Wilink 8 WL18xx) http://wiki.solid-run.com/lib/exe/fetch.php?media=imx6:microsom:docs:sr-usom-mx6-pcn-20160915.pdf This is from the solidrun website: Make sure that your kernel .config has the following enabled either as modules or statically part of the kernel, in order to build the TI WiLink8 WiFi drivers -CONFIG_WL18XX=yCONFIG_WLCORE=yCONFIG_WLCORE_SPI=yCONFIG_WLCORE_SDIO=yCONFIG_WILINK_PLATFORM_DATA=yCONFIG_WL_TI=y# CONFIG_WL1251 is not set# CONFIG_WL12XX is not setThe firmware i…

the current filogic kernel has no info [in github] for where it was forked from, and trying to apply incremental patches from kernel.org I found it contains pieces of 6.14 in an ostensibly 6.12 branch. @chainsx might you be able to divulge where you forked it from?

I don't see it specifically listed, but does Armbian run on the Beaglebone black?

First of all, sorry if I'm asking something really obvious, but I'm new in Linux. Hi! I just have a new fresh install of Armbian Stretch on my Cubox, and I just realized that Armbian isn't using the Predictable Network Interface Names but the old one. root@opl-cubox:/home/lpuerto# ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.6 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::d263:b4ff:fe00:8297 prefixlen 64 scopeid 0x20<link> ether d0:63:b4:00:82:97 txqueuelen 1000 (Ethernet) RX packets 411 bytes 50456 (49.2 KiB) RX errors 0 dropped …

This post is, more or less, a continuation of something I started here, but adapted to Armbian. I will start with an overview of what I have done (maybe this is relevant) and finish with my questions. What I've done: I have a Hummingboard Gate with a Mikrobus RS485 click 3.3V (this one: https://www.mikroe.com/rs485-33v-click). In order to make this work I need to change a few things in de device tree. The dtb that my board uses is 'imx6dl-hummingboard2.dtb' so I copy that file to my home directory for safe keeping. cd ~ sudo cp /boot/dtb-4.19.18-cubox/imx6dl-hummingboard2.dtb . Then I convert this dtb to a dts: sudo dtc -I dtb -O dts -o im…

U-Boot 2017.05-armbian (Nov 30 2022 - 10:45:39 +0000) for ODROID-XU4 CPU: Exynos5422 @ 800 MHz Model: Odroid XU4 based on EXYNOS5422 Board: Odroid XU4 based on EXYNOS5422 Type: xu4 DRAM: 2 GiB MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 MMC Device 0 ( SD ): 59.5 GiB Card did not respond to voltage select! mmc_init: -95, time 11 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Press quickly 'Enter' twice to stop autoboot: 0 ** File not found /boot.ini ** ## Executing script at 43e00000 Wrong image format for "source" command 12548 bytes read in 44 ms (278.3 KiB/s) ## Executing script at 43e00000 111 by…

The hummingboard edge has a RS485 port on UART2? What would it take to get to get this running? The latest build does not have ttymxc1 enabled. And I think the driver for the RS485 is different than the normal RS232 Driver. thanks

Hi Guys, First thanks fo rthe hard work, but as in other threads here every now and again we get an issue moving up kernel versions. Mostly this is a post to flag up I had issues, so might you and that reverting the kernel fixed it for me. I did an apt-get update; apt dist-upgrade (I run this every other day normaly) and it did a kernal update from Linux cubox 5.9.14-imx6 #20.11.3 SMP Fri Dec 11 20:57:51 CET 2020 armv7l GNU/Linux to Linux version 5.10.12-imx6 It appears to all work.... however I use my Cubox-i to be a server for Kodi. When I play flac files (which are quite big) it down loads th…

Hello, I have problem with sata port multiplier. I can't make it work. All recommended changes for boot.cmd made. Any single SATA drive could be detected, but doesn't works via pmp. What else can be done? Dmesg attached. dmesg.txt

Hey guys, since noone seems to care at the solid-run forum, I ask here. I would like to compile SDL2 with opengles and vivante support. I've installed the drivers from this post http://forum.solid-run.com/linux-on-cubox-i-and-hummingboard-f8/about-opengl-drivers-and-binary-blobs-packages-for-t2013.html With both versions of debian (armbian and the official) ./configure can't find these drivers, all I get is "dummy" for the video driver. With arch linux there were no problems at all, it worked right out of the box. Does someone have a hint for me. This is my last hope. Thanks in advance McCarthy

Hi, I am making Asterisk PBX over Orange Pi - 2g IoT, I have tried Armbian as well as Ubuntu. Everything is working fine, but I am stuck on two issues, a. How to add built-in GSM module of Orange Pi 2g IoT board in asterisk, so that A GSM trunk call/text can be transferred on SIP extension. I know chan-dongle, but asterisk is not detecting GSM module. I ahve tried different versions of asterisk. b. How to change IMEI of Orange Pi 2g IoT Looking for solutions Regards

Hi all, I was an early adopter of cubox-i (and cubox before) By that time I was able to install Ubuntu 12.04.5 LTS server and use my cubox-i to host owncloud, resourcespace, phplist, roundcube and other applications. Now I would like to upgrade (using another sd card) to Armbian_5.38_Cubox-i_Ubuntu_xenial_next_4.14.14.7z Everything seems fine, except the fact that I can't import mysql data from mysql Ver 14.14 Distrib 5.5.54, for debian-linux-gnu (armv7l) to mysql version 5.7 (skip one version is not supported) Do you have any suggestions ? Thanks a lot

I installed a TPLINK wifi dongle, but when trying to set the interface up, i get the message of the subject. What can it be? Thanks! root@kraken:/etc/nginx/sites-enabled# ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,DYNAMIC,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether d0:63:b4:00:1d:57 brd ff:ff:ff:ff:ff:ff 3: wlan1: <BROADCAST,MULTICAST,DYNAMIC> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether c…

Hi everyone, since upgrading to the new stable build DKMS refuses to compile any driver package for the 8812au Wifi chip I could find on github: make ARCH= CROSS_COMPILE= -C M=/root/rtl8812AU modules make[1]: *** M=/root/rtl8812AU: No such file or directory. Stop. Makefile:1576: recipe for target 'modules' failed make: *** [modules] Error 2 I did change the makefile to reflect compiling for ARM. This procedure worked on the old stable kernel. Is there a way to modify the Makefile or kernel sources to accept the new kernel...or is something borked with my system? The error message does not point me to a direction to check for a fix. C…

Need help in finding a suitable Debian build for Sabre Board running imX6 Quad from Freescale.

Hi Igor, is there a possibility to compile HummingBoard image with libmmal.so, from Raspberry Pi?

Hello, I have an orange Pi i96, and I can't find a USB device. In /dev, I have a serial folder, then by-id in which I have : usb-1a86_USB_Serial-if00-port0 But it doesn't disappear when I remove the USB device ... And the USB output doesn't change whether the device is plugged in or not. Dmedg gives nothing related to usb and lsusb gives this: Bus 001 Device 002: ID 1a86:7523 QinHeng Electronics CH340 serial converter Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And it doesn't change depending on whether the USB port is busy or not. Am I missing something? Have a nice day I know it's the wrong ta…

Hello good people, I recently started "porting" linux to my Huawei mate 9. Its one of those projects plagued with silly issues and a sad lack of docs and unreliable hearsay. I was hopeful someone may have started something similiar, or maybe commit logs/discussions from when Hikey960 support was added. Ive found commits but praying that maybe more exists. I just have a handful of basic questions, most unfortunately involve things like the android bootloader. Which partitions related to boot can safely be replaced with non signed images, how do i stop fastboot from combining the appended dtb with those in dts partition. Just to give a general sense of what im l…

Hi, I installed Armbian on a Cubox 4x4, I realize this was designed for a different board, but in general it works. But I found there was a problem with the system clock, it kept booting up with the time: Thu 01 Jan 2015 10:07:23 AM CET After some investigations, I found that this board has two hardware clocks: /dev/rtc0: Thu 01 Jan 2015 10:05:17 AM CET -0.616496 seconds /dev/rtc1: Fri 13 Nov 2015 08:23:47 AM CET -0.603090 seconds It looks like rtc1 has a battery and survives reboot, but /dev/rtc0 does not. I tried setting the clock using "ntpdate" on boot, but I found that something kept resetting the time. I found it is /etc/rcS.d/S06hwclock.sh …

Hi, I installed Debian wheezy I tried to connect via ssh with ethernet connection and it works well , but if I try to connect with the wifi connection is blocked after entering the password , it is a bug cubox? . If you can serve the ouptu ssh -vvv it is : marco@kali:~$ ssh -vvv 192.168.x.x OpenSSH_6.0p1 Debian-4+deb7u2, OpenSSL 1.0.1e 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.x.x [192.168.x.x] port 22. debug1: Connection established. debug1: identity file /home/marco/.ssh/id_rsa type -1 debug1: identity file /home/marco/.ssh…

Hi I have spent a lot of time with the Hummingboard2 Edge over the last months and i would like to share my experiences here. My Configurations is: Hummingboard 2 Edge with SSD Sata and MC7304 PCIE Lte Modem. Carrier Board is V1.2. Microsom is version 1.5. They are available since end of 2016. The difference is the WLAN and Bluetooth Module. Solidrun has changed it from Broadcom to TI Wlink 1831. First of all. If you have an unfused Microsom and you want to use the bootjumpers. (Only Carrier Board V1.2) Boot from SD: Set Jumper to SD (J5005 Pin 7 and 8) and (Connect J23 Pin 11 with J24 Pin 2 and with J21 Pin 5 Boot from MMC: Set Jumper…

Hello, i have Hummingboard 1 with mainline kernel 4.11.6. And i have problem with GPIOs, after exporting GPIO 72 (also i try 73,71,1 / pin 11,13,7), set direction to OUT and value to 0 i have still 3.3V on pin 12 (11,13,7...). Also try 72 as OUT value 1 and 73 as IN ... and short this pins 11-12 by wire. gpiochip2: GPIOs 64-95, parent: platform/20a4000.gpio, 20a4000.gpio: gpio-68 ( |PCIe reset ) out hi gpio-69 ( |gpio-ir-recv ) in hi gpio-72 ( |sysfs ) out hi gpio-73 ( |sysfs ) in lo gpio-83 ( …

Finally got an UDOO quad Trusty image built. How do I get it out of the virtual environment? Shared folder?

Hello, I am trying to run urbit on my CuBox-i 4×4 and it looks like ARMBIAN 5.25 stable has some kind of kernel config that limiting the memory usage: ./urbit -c mytestcomet ~ urbit 0.4.4 urbit: home is mytestcomet boot: mapping 2048MB failed see urbit.org/docs/using/install for adding swap space I have added a 4GB swapfile but it seems it's not addressable by the urbit process, I also tuned the setting vm.swappiness without any success. Could this be related to the kernel config CONFIG_VMSPLIT_2G? Details: ---- Kernel setting cat /proc/config.gz |zcat |grep -v "^#" |grep VMSPLIT CONFIG_VMSPLIT_2G=y top top - 20:24:55 up 4 min, 1 user, l…

Hello! I'm trying to boot latest releases of of Armbian (following images: Armbian_21.02.3_Cubox-i_buster_current_5.10.21.img and Armbian_21.02.3_Cubox-i_focal_current_5.10.21.img) on a Solid-Run Hummingboard2 Gate V1.4 board. (Board V1.2 freeze during Uboot) I'm getting to the "Starting kernel" message but after that things stop. Switching on the verbose output in ArmbianEnv.txt result in the output below where the kernel always stop at message: [ 0.000000] Freeing unused kernel memory: 2048K Do anyone have any thoughts/ideas here on what could possibly be the problem stopping the kernel from booting? U…

Hi All, Looking for assistance with getting an old SmartQ5 Mobile Internet Device running with Armbian. I was able to locate Github page (https://github.com/tpruvot/smartq-magicsd) which references booting from SD but need assistance getting armbian compiled and configured for the device. Any help is appreciated! SPECS: Samsung Mobile Application Processor S3C6410 based on ARM11 core at 667 MHz/800 MHz 128 MB DDR 133/333 MHz SDRAM 1 GB NAND FLASH (256 MB usable for storage) AC97 audio codec & PCM 24-bit audio SoC graphics unit, OpenGL ES 1.1/2.0, 4M triangles/sec @133Mhz (Transform only) Integrated Wi-Fi 802.11b/…

Hello everyone, I am a beginner in Linux. I have a Hummingboard i2ex and I am running Armbian_5.30_Cubox-i_Ubuntu_xenial_4.11.4_desktop on it. Trying to use a CSI Tool, I have to compile and install this kernel : https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git Here are the steps that I did on the Hummingboard: ( you can see the tutorial: http://pdcc.ntu.edu.sg/wands/Atheros/document/Atheros-CSI-Tool-User-Guide.pdf ) 1) sudo apt-get install git (to clone the source) 2) sudo apt-get install libncurses5-dev libncursesw5-dev (to run makemenuconfig) 3) git clone https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git 4) Enter the dir ~/Atheros…

Hi there, Just loaded Armbian Vanilla Jessie (5.00, 4.4.1 kernel) on one of my Cuboxes. There's no sound from SPDIF, even though it's seen: root@cubox-i:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Speaker-test shows no errors: root@cubox-i:~# speaker-test -r 44100 -F S16_LE -c 2 -D hw:0,0 speaker-test 1.0.28 Playback device is hw:0,0 Stream parameters are 44100Hz, S16_LE, 2 channels Using 16 octaves of pink noise Rate set to 44100Hz (requested 44100Hz) Buffer size range from 64 to 16384 Period size range from 32 to 8192 …

I set up NanoPC-T3 as a router, the upsteam Ethernet port is connected to a router. However, the bandwidth drops dramatically whatever I’m using IPTables or network bridge to forward the data. This doesn’t happen on the other SBCs I have. How can I solve it?

Hi There, I would like to run Linux5 or Linux6 on Jetson nano, display using HDMI-DVI adapter. It worked fine with Jetpack4 (=Linux4). When I boot with armbian/Linux5.10, which is linux-image-current-jetson-nano, the display tells me it is out of sync then I would force the display as 1280x1024@60Hz, since it looks like Linux fb or X11 are trying to use 1280x1024@75Hz, so that I need edid/1280x1024.bin (maybe with video=1280x1024@60) using {linux-source}/tools/edid to maintain the resolution and sync. I tried both of gcc-10 and gcc-9 to build it, but failed with below error: edid.S: Assembler messages: edid.S:274: Error: cannot represe…