Beginners

Hello, I would like to have some help with the video in Armbian. I have migrated to it and I want to make it the best possible. I hope there is some things I can do to make it run smoother. It is ok with small screen but not with full screen. I have a Tinkerboard S.

Hello, My mic works on my laptop, but I tried to do the computer, but the mic is not working. I tried a troubleshooter, allowing audio to be recorded. I have tried to reinstall the drivers, but nothing seems to be working. Even after doing a lot of research, the solution was not found. Then after going to the settings, after looking at the setting of the microphone, it came to know that the microphone needs permission to run in the device which was disabled. At the same point, after I have given permission in the settings, the microphone was not working due to not giving it, then the https://mictests.net is checking the mic from the site and see if…

I loaded a kernel module from the official Linux Github repo, compiled and placed it within /lib/modules/......... Now if I make changes to this kernel module, and recompile it and reboot, the old one still gets called. If I rmmod and modprobe however, the new module gets loaded. The module I'm talking about is qcaspi. This issue doesn't occur on RPi so I'm thinking it could be an Armbian issue or an oversight by me. Any help please?

Hello, I run a clearfogpro, this problem is not board specific, but I would like to use a huawei e3372h-153 USB 4G dongle on this board which has a USB3 port. The current version of armbian is Debian Buster Linux 4.14.135-mvebu. This dongle is in stick mode, as opposed to the hilink mode. In stick mode, when plugging the dongle, two devices appear : /dev/ttyUSB0 and /dev/cdc-ncm1. With the former I can issue AT commands to the dongle, the latter is the modem itself with the NCM protocol, known to be faster than PPP. There is also an wwan interface appearing with ifconfig -a. However, I do not know…

Hello, I just started a new SD card with 21.02.3 Buster on a OrangePi PC+. In armbian-config I can't install on eMMC: it says nand-sata-install: command not found. thanks Mathieu http://ix.io/2UhB

Hi !as title say i can not fully boot after reboot for electric failure. I have the boot partition on my sdcard then normaly boot on the encrypted ssd system debian buster with 5,4 system.(Linux gre 5.4.102-odroidxu4 #21.02.3 SMP PREEMPT Mon Mar 8 07:55:51 UTC 2021 armv7l GNU/Linux) I can access to initramfs run cryptroot-unlock script ,unlock the encrypted drive, then initramfs disconnect me and ... nothing, i can not view my HC1 on the network So I tried to boot on the sdcard system and could unlock the SSD and chroot on the ssd. i see logs but nothing helps me to resolve my problem. I share you my log if you can help me : messagesmessa…

I have a carrier board from codico: https://www.codico.com/en/carrier-board-h-home-control-evb-for-red-yellow-beet-modul I've followed the pdf file from the above link to set up a Rasperry Pi and it all works fine. However, when swapping for my NanoPi Neo Core, even though the drivers load correctly, and I see SPI comms going back and forth on the oscilloscope, I am not connected to the internet. This is what ifconfig returns: What could be the difference between rpi and this board that this happens? Any guidance on how to resolve it would be deeply appreciated!

Hi all, I have a working Pinebook Pro Focal build with LUKS encryption enabled. The only issue I have is that when booting no progress or password prompt is displayed. As soon as I enter the password and hit enter I see the boot logo or console output depending on what is set in armbianEnv.txt. I will be continuing my research and learning about the boot process in general but wanted to check in here to see if people had any obvious pointers to share or whether maybe this is a known limitation that is going to be hard to resolve. Thanks, Matt

Hello I put an image of Armbian on a micro-disk and was able to start with, and was able to start an HC1 with it. Now I put the disk in an HC2 it does start also fine. But I could not find the IP address on the network. Not with nmap and not with the utility on the provider modem. What could be wrong? Freerk Jongsma

I installed buster (5.10.21-sunxi) on an Orange Pi zero. I'm trying to install a package using a python venv which required python 3.8 but buster comes with python 3.7. I tried to update using this set of commands sudo wget https://www.python.org/ftp/python/3.8.2/Python-3.8.2.tgz sudo tar xzf Python-3.8.2.tgz cd Python-3.8.2 ./configure --enable-optimizations make -j 4 sudo make altinstall I tried to create a virtual environment with python3.8 -m venv /srv/myapp but I get this error Error: Command '['/srv/myapp/bin/python3.8', '-Im', 'ensurepip', '--upgrade', '--default-pip']' returned non-zero exit status 1. What does it mean? How c…

Hello folks, I have been banging my head on this for a few days now and after many searches what should work it is not working :-( I'm setting up an NTP server on a NanoPi Neo3 board (RK3328) running Armbian and I'm stuck on getting the PPS to work. I have a GPS connected issuing the PPS signal on pin 16 but I don't seem to be able to make it visible to the NanoPi. Here are the usual reports to show what OS I'm running. "cat /etc/armbian-release" # PLEASE DO NOT EDIT THIS FILE BOARD=nanopineo3 BOARD_NAME="NanoPi Neo 3" BOARDFAMILY=rockchip64 BUILD_REPOSITORY_URL=git@github.com:armbian/build.git BUILD_REPOSITORY_COMMIT=e846ef656…

I am building a media player using BananaPro (also called BananaPi M1+?). I am doing: 1. Burn a SDCard. 2. Boot and set user and password. 3. Enable USB Massage Storage insmode g_mass_storage.ko file=a_sdcard_partition_or_a_big_file removable=1 echo "2" >/sys/bus/platform/devices/sunxi_usb_udc/otg_role stuck here 4. Install a media player and get H264 HW decoder working 5. ... And I found that /sys/bus/platform/devices/sunxi_usb_udc/otg_role is not exist. Than edited usb@01c13000 part in dtb file to change status = "disabled" to change status = "okay", and the board would not boot any…

Hi guys! I need to run some game on full screen, and they are old school windows one. the thing is that adding the modeline worked perfectly fine on rpi4, not on armbian sadly. it seems to change the resolution and then it go "out of signal". I used the same parametes than on rpi4. also generated new ones just in case. the thing is I cant make it to work and maybe iut's something deep into armbian. exaple: xrandr --newmode "640x480_60.00" 23.75 640 664 720 800 480 483 487 500 -hsync +vsync xrandr --addmode HDMI-1 640x480_60.00

Hello everyone. I have to change drivers code in ./cache/sources/linux-mainline/linux-5.10.y/sound/soc/codecs/ Which is the best way to compile a single sound driver without building all the kernel and without lost modification. I would like to work in my Ubuntu pc build Armbian directory.

I burned a xz compressed image of Armbian Focal onto a good SD card using BalenaEtcher as instructed on the Armbian website. I placed it into my NanoPC T4 - which currently boots from the eMMC, and held the boot button while powering on. It tried to boot - but it kept reporting there was no bootloader file and seemed to be trying to load something from the internet, not the SD card. If I dont press the boot button, it simply ignores the SD card and boots from eMMC. I reburned the SD card several times, and each time it verified fine. Does anyone know what I did wrong?

I have a Ubuntu Server 18.04 with postfix installed and configure it the same way as I did on my Helios64 running Armbian 21.02.3 Focal. Last week, one of my older drives died in the Helios, but I didn't get an email about this. My Ubuntu Server 18.04 will send me mails as soon as there's an issue in the SMART values from the drive. I didn't had to configure anything to do that apart from postfix. I can send a test mail from both my Ubuntu Server 18.04 and my Helios64 Armbian and receive both. Any idea what the reason is that my Ubuntu Server 18.04 is sending me those emails by default and how I could enable this on my Helios64?

Hello All, It there a way to install Amiberry (Amiga Emulator)? I'm trying to set this up on my XU4 w/ Armibian Buster. Thanks

I have tested different desktops, window managers, OS and kernels, but the problem persists. The problem: When I move a window on the desktop, the cursor icon flicks. If I use no GPU driver (LLVMpipe), no problem! Tested on; SBC: Odroid-C4 OS: Focal, Buster and Hirsute Desktop: Xfce, Mate, Gnome, LXQT Window Manager: OpenBox, Mutter, Xfwm4, Metaccity Panfrost: 21.0 and 21.0.rc5

Hello. I'm using the latest image from https://www.armbian.com/rock64/ installed today. As description say, it is possible to overclock the board to 1.5ghz, but it didn't work. root@rock64:~# cat /sys/devices/system/cpu/cpu{0,1,2,3}/cpufreq/scaling_available_frequencies 408000 600000 816000 1008000 1200000 1296000 408000 600000 816000 1008000 1200000 1296000 408000 600000 816000 1008000 1200000 1296000 408000 600000 816000 1008000 1200000 1296000

Hello all, I'm trying to install a WireGuard docker's container on my Odroid HC4 with installed "Armbian 21.02.3 Buster" with "Linux 5.10.21-meson64", but I have a problem... When I try to deploy, I get this error in the log: **** Kernel headers don't seem to be available, can't compile the module. Sleeping now. . . ****, **** No kernel headers found in the Ubuntu or Debian repos!! Will try the headers from host (if mapped), may or may not work **** I tried to run: sudo apt install linux-headers-$(uname -r) but the result is: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package l…

I'm trying to update in Htoo_Armbian and being prompted for my [sudo] password. I almost always use one password for all my Linux devices, so I may have set up a password during initial install of Armbian--don't recall. How do I recover my password, enter a new one w/o reinstalling the whole OS?

Hi there. I have some audio project on different SOM/SOC boards, now my task is to bring an i2s DAC on RK3399. I use external high-quality clock for i2s and need to make the Rockchip the masterclock slave. This is the case where I find no tail to pull yet, due to VERY cumbersome device tree, poorly documented and poorly explored. For instance, the CPU datasheet says that I2S_MCLK is output only, whilst I could find the opposite in the TRM. Moreover, the clock tree explained there, says that I can use CLKIN_I2S not only for i2s interfaces, but for spdif also! (Also there is explained some "bitclock slave mode", it's even implemented in the DAI driver,…

I'm trying to build an image for an Olimex A13-Som board. So far it starts booting, but halts when it gets to: "Starting Raise network interface...". I've tried all the available distribution in the builder, (Bionic, Buster, Stretch, Focal etc.) and it's the same for all of them. I quite can't figure out how to get it to move past that point - anyone got a suggestion? Regards.

Hi, in my case the test is on a Rock64 (4GB, v2 edition) using latest current Buster or Focal. The problem is in the first init configuration assistant. When selecting the "User language based on your location", after selecting es_AR.UTF-8 (I am from Argentina) it "auto-detects" my keyboard layout as AR which belongs to Arabic iirc (which is wrong). After this of course I can't type anything right on terminal. I had to fix it over ssh by issuing the command: sudo dpkg-reconfigure keyboard-configuration.

hello dear all - good day I need a Operating-System for - Alwinner /banana Pi A 20 - Udoo Quad Makerboard Rev. D. - Orange PI Prime rev 1.0 which one to take!? btw: see the data for the UDOO - Quad Makerboard Rev. D. found the following specs Note i want to build up a NAS/ Samba server. can i do that with this UDoo quad I look forward to hear from you btw: plz keep up this great project - it rocks!

I'd like some help please. The ethernet device naming seems inconsistent and sometimes changes following reboots. Sometimes one interface comes up as eth0 and sometimes as eth1, and sometimes not at all. The enp1s0 interface seems to reliably come up, but not with the right config (sometimes it uses the config for enp1s0 and sometimes for eth0). I am trying to assign status IP addresses (on different networks) to each interface, but because of the unreliable bringup of the network interfaces, I can't get a config that starts up correctly and consistency on reboots or cold boots. As a test I ran the friendly-core-lite-focal from …

I'm finally realizing that I have no swap and zram is not enabled. I just checked /etc/default/armbian-zram-config and ENABLED=false I'm running Armbian buster with Linux 5.4.49-rockchip64 on a RockPi4A. Is zram turned off by default? Did I screw up/miss a step when setting up my system (quite a while back)? My system boots from an SD card. I have no SSD in the system just SATA and USB HDD. I've been having system hangs when memory runs out (which has not been frequent but is very annoying) I run most things in Docker, so if I needed to rebuild from scratch it's not the worst thing in the world. Espe…

Hi all, I think i have made a mistake but i don't know what. Do someone know what goes wrong? Yesterday i have played with the PCIe port on the Orange Pi 4 with the original extension module. Plugged in a Dell (Ericsson) 5560 HSPA in the board and it works all fine. It was detected. Did not get the connection working with sim tray but ok. It works and reacts on AT commands. So far so good. Then i tries to plugin a wifi card (doesn't know exactly wich one. I thought Intel 6230) but didn't want to boot and a green led lights up on the PCIe board what i has never seen before. After that i thought: ''hmm, there is here laying a old Dell Latitude D630. …

I have read a few forum posts on the topic but I'm still not convinced. Which one is safer and more stable for Armbian based NAS? I previously had issues and data loss on BTRFS. However I now hear that it's much more stable. I been using ZFS on FreeBSD without any issues for years and I would prefer it but it seems that it's a hit and miss to get it working. I just did and it was very easy but I read that people have random issues with upgrades etc. Any thoughts? Thanks! a

I am running rsyncon my rockpi nas pulling from another nas and the performance initially pretty good at around 90MB/s and after a while, it degrades to 39Mbs with high io/wait times - any ideas/suggestions are welcome. Here are the outputs of amrbianmonitor -U Time big.LITTLE load %cpu %sys %usr %nice %io %irq CPU C.St. 15:33:55: 600/1416MHz 0.85 4% 1% 0% 0% 1% 0% 41.7°C 0/6 15:34:00: 600/1008MHz 0.78 1% 0% 0% 0% 0% 0% 41.1°C 0/6 15:34:05: 816/1200MHz 0.72 1% 0% 0% 0% 0% 0% 41.7°C 0/6 15:34:10: 1800/1200MHz 0.66 10% 5% 4% 0% 0% 0% 46.9°C 0/6 15:34:16: 2016/1512MHz 0.85 39% 2…

HI folks, I wonder how to do that.. it's that simple. on RPI OS is just ctrl + alt + F4, maybe here is more complex.

Hi Igor, did you change your sig? # gpg --keyserver ha.pool.sks-keyservers.net --recv-key DF00FAF1C577104B50BF1D0093D6889F9F0E78D5 gpg: key 93D6889F9F0E78D5: public key "Igor Pecovnik <igor@armbian.com>" imported gpg: Total number processed: 1 gpg: imported: 1 # ls -la total 384004 drwxr-x--- 2 dev dev 80 Mar 12 01:38 . drwxrwxrwt 21 root root 540 Mar 12 01:38 .. -rw-r--r-- 1 root root 396181864 Mar 12 01:12 Armbian_21.02.3_Nanopineo2_buster_current_5.10.21.img.xz -rw-r--r-- 1 dev dev 833 Mar 12 01:38 Armbian_21.02.3_Nanopineo2_buster_current_5.10.21.img.xz.asc # gpg --verify Armbian_21.02…

Hi I've installed Armbian_21.02.3_Tinkerboard_focal_current_5.10.21.img on my Tinkerboard. # uname -a Linux tinkerboard 5.10.21-rockchip #21.02.3 SMP PREEMPT Mon Mar 8 07:34:33 UTC 2021 armv7l armv7l armv7l GNU/Linux I'm not able to create a bridge with a WiFi interface: brctl addbr br0 brctl addif br0 eth0 brctl addif br0 wlan0 can't add wlan0 to bridge br0: Operation not supported wlan0 is the onboard WiFi. I also tried several usb WiFi dongles with the same result. Any hint? Regards, Chris

After flashing the last release (21.02.3) of Buster for Orange Pi One Plus H6 I discovered that no sound card was available. aplay - l gave: Then flashing a one year old version (20.02.1) the hdmi audio was available. But after making the updates, apt-get update , apt-get upgrade and enabling the Desktop aplay -l gives : no soundcard found. Please Help Regards https://www.fiatb.fr

Hallo After apt-get upgrade my pi-hole and transmission is not working. Both running and I can see it when type htop. But I cant use web interfaces. It is without graphic.

Lubuntu Focal / Panfrost Download the latest current version of Focal (Panfrost drivers included) for your device and follow the instructions https://www.armbian.com/download/ After the first login type ... exit (exit from root, login with the new user id entered in step 1) Download the Panfrost Tester script git clone https://gist.github.com/8f8b0cd40e95ac18c539cd29ecd4c3d2.git install-panfrost-tester cd install-panfrost-tester Version 21.0.0-rc5 will be installed. If you wish, you can modify the mesa branch using: nano installPanfrostTester.sh (ex: go to install mesa line and change from 21.0 to master…

Hi, I am using OV5640 in Nano PI duo 2 kernal: Linux nanopiduo2 5.10.16-sunxi #21.02.2 SMP Sun Feb 14 21:12:17 CET 2021 armv7l armv7l armv7l GNU/Linux I found that NanoPi Duo2 - FriendlyARM WiKi which is kernal 4.14 supports camera OV5640. Do Armbian Focal (mainline based kernel 5.10.y) have support? if not Please say how to do it? I am new to this armbian kernal Thanks in advance

Hi, I'm trying to work with the CedarX/Cedrus Video Engine (running in Allwinner A20). It works smoothly with my patched FFmpeg; for example: ffmpeg -f v4l2 -r 30 -pix_fmt nv12 -video_size 1280x720 -i /dev/video0 -vcodec cedrus264 -pix_fmt nv12 -qp 15 -f rtsp -rtsp_transport tcp rtsp://192.168.10.11/live/test I need to use pixel format RGB24, but as far as I understand, I'm limited to work with NV12 (or NV16) pixel format. Does this limitation is due to: My FFmpeg patch (I think not...) CedarX/Cedrus driver implementation. Hardware limitation. Thanks for the help, Joseph

Dear All, I managed to install Armbian on my H96 Max RK3399 box by using the nano-pc-t4 image Armbian Focal, and rockpro64 dtb. I am also able to boot to Armbian Twister OS by using Armbian Reforge u-boot as I mentioned in my previous post: Everything works fine. Even I managed to activate the internal wifi QCA9377 (ath10k_sdio) by installing the Full Armbian Firmware via armbian-config. I also installed the bluetooth module via armbian-config. The buetooth status is active But the bluetooth is not working. $ service bluetooth status ● bluetooth.service - Bluetooth service Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor…

Hi, I'm trying to work with the CedarX/Cedrus Video Engine (on Allwinner A20). It works smoothly with my patched FFmpeg; for example: ffmpeg -f v4l2 -r 30 -pix_fmt nv12 -video_size 1280x720 -i /dev/video0 -vcodec cedrus264 -pix_fmt nv12 -qp 15 -f rtsp -rtsp_transport tcp rtsp://192.168.10.11/live/test I need to use pixel format RGB24, but as far as I understand, I'm limited to work with NV12 (or NV16) pixel format. Does this limitation is due to: My FFmpeg patch (I think not...) CedarX/Cedrus driver implementation. Hardware limitation. Thanks for the help, Joseph

If possible, I would like to shutdown or wake up the Odroid N2 using a GPIO button. I followed the guide here: https://wiki.odroid.com/odroid-n2/application_note/gpio/gpio_key_wakeup. The button LED works, but the button does not trigger shutdown or wake up using pin 9 and 11. Has anyone gotten a power button to work on the Odroid N2? Is there a specific Odroid module/software that isn't installed by default in Armbian? Additions to /boot/boot.ini setenv gpiopower "479" setenv bootargs ${bootargs} gpiopower=${gpiopower} After these additions, /proc/cmdline shows "gpiopower=479" as expected. I'm running Armbian 21.02.2 Buster on the Od…

Hi, I'm trying to run with a PREEMPT_RT kernel to get a real-time (lowest latency as possible) performance. But in addition to the PREEMPT_RT patch, I want to make sure the system doesn't go to sleep (or using power save modes) to avoid additional wake-ups latencies (that the PREEMPT_RT patch cannot reduce). I've reviewed the AXP209 datasheet and tried to understand if I can somehow disable the system from going to sleep, but I didn't find the answer for that. I do know that register 0x31 can control the entrance to sleep mode if we write '1' to bit-3, but I can't prevent other drivers or applications from doing it. Question: Is th…

Hello all, I want to build armbian for Pinebook Pro with LUKS enabled but I'm hitting this error. This is happening regardless of build environment (I've tried virtualbox, docker, vagrant) or board selection (most recently I tried building orangepipcplus). .... ] Installing [ armbian-focal-desktop-gnome_21.05.0-trunk_all.deb ] [ error ] ERROR in function install_deb_chroot [ image-helpers.sh:148 ] [ error ] Installation of /root/armbian-focal-desktop-gnome_21.05.0-trunk_all.deb failed [ pinebook-pro focal yes rockchip64 ] [ o.k. ] Process terminated [ o.k. ] Unmounting [ /root/build/.tmp/rootfs-712d9aa2-7aa7-4e20-ae2e-21136ed09662/ ] [ er…

Hello, I have an Odroid C2 with Armbian 21.02.2 Buster with Linux 5.10.16-meson64 I use a bluetooth usb key (CSR 4.0) but hci0 is down and I can't get it up. root@jeedom:~# lsusb Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port Bus 001 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@jeedom:~# hciconfig hci0: Type: Primary Bus: USB BD Address: 00:1A:7D:DA:XX:XX ACL MTU: 679:8 SCO MTU: 48:16 DOWN RX bytes:1468 acl:0 sco:0 events:48 errors:0 TX by…

Trying to set frequencies and governor for both types of CPUs on this processor. armbian-config sets the max freq and governor correctly for the two big proccesors but no config for little. Tried cpufreq-set for little, but it does not respect governor. If its set to a freq is stays there indefinitely, and if conservative governor is set the max freq goes back to 1.5. How do we set max freq to 1.2 for little, and governor to conservative and have both stick like big does with armbian-config?

Having downloaded the Armbian OS for my Cubox-i, I am using Gparted on MXLinux to prepare my 32Gb microUSB card for installing the extracted image. My initial problem is that I have to select the partition table type to install, from a list with msdos being the default. Is msdos the correct type or should I use one of the others offered (sun, gpt, bsd, dvh, aix, loop, pc98, amiga, atari, mac) Once that is done, what filesystem should I use to create the new partition as there are so many choices available. I appreciate any help you can provide to get me going. Thanks Ashdown

Hello, From the subject of this topic it may sound like a very common and must-know question. But trust me I am struggling to add my custom prebuilt apk in to the Android 10 AOSP to include it in my custom ROM. What I have tried so far; 1. I have added a directory of my_app_name in <aosp_dir>/packages/apps/. Added an Android.mk file with below content in it, Placed my apk with that Android.mk in same directory. This did not work, I am not able to find any my_app_name.apk in out/targte/product directories. LOCAL_PATH := $(call my-dir) include $(CLEAR_VARS) LOCAL_MODULE := my_app_name LOCAL_MODULE_CLASS := APPS LOCAL_MODULE_TAGS := o…

Not related to armbian distribution, just curious. I googled but had no luck to find an answer. For Allwinner SoCs, there is FEL boot tool to download bootloader, kernel and initramfs to ram and to boot the system directly, without writing those stuff onto flash storage and performing a reset; I wonder whether there is a tool to achieve the same function for rockchip SoCs? or we could modify the usbplug and rkdeveloptool to implement the function? or there are any limitations to prevent it? any comments or advices?

I can run device with compatible dtb(but has bug),so I write for myself. But the dtb that I compile can't start. So I want to compile dtb quick and debug. I only know `compile.sh` to build complete img but to slow, How to only compile dtb?(like `make ARCH=arm64 dtbs`)

Hi, I'm a beginner for orange pi series, so I bought an orange pi pc+ and I tried to use load cell with HX711. I've searched all github links and common forums but I couldn't find anything about to reading HX711 by orange pi pc+ or any device using armbian os. If I need to explain in more detail, I've checked the HX711 libraries to use reading functions of gpios. Is there anybode help me. I want to use Orange Pi in my bachelor thesis because it is cheaper than Raspberry Pi so I really need help.

Dear members of the forums. I am shopping for a new single board computer, already have a few manufacturers, but I am not sure yet. Couple years ago I bought BPI-M2U from Sinvoip, and I regretted that soon. Sinvoip was not providing good documentation nor open source contributions of drivers. So to avoid the same situation, I'd like to ask which manufacturers are co-share, contribute to open source and don't sell boards with schematic errors? Orange Pi (4) Khadas (Vim3) Friendly Elec (m4) Odroid (N2) Thank you in advance and sorry if this is not the right forum.

I'm having an aggressive memory leak issue I can't place: Within 5 minutes the 4GB are full. htop and top don't show a massive program growing unbouded. `df` doesn't show a tmpfs that is too large. Only `slabtop` is imforative: OBJS ACTIVE USE OBJ SIZE SLABS OBJ/SLAB CACHE SIZE NAME 26638624 26638624 99% 0.12K 832457 32 3329828K kmalloc-128 So `kmalloc-128` is growing without bounds. As I understand it kmalloc is a collection of smaller memory allocations? I've tried using a previous kernel version (5.10.16 and 5.10.12) but nada. I've disabled docker, and that along with omv were the only services running…

Hello ! Since last armbian update (5.10.16-meson64 #21.02.2 SMP PREEMPT) the quirks option added to the armbianEnv.txt file is not added to the boot command line at boot time armbianEnv.txt verbosity=1 console=both overlay_prefix=meson rootdev=UUID=722afb48-c000-4b51-a382-ae3a7b132c86 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u,0x2109:0x0715:u Boot log Kernel command line: root=UUID=722afb48-c000-4b51-a382-ae3a7b132c86 rootwait rootfstype=ext4 console=ttyAML0,115200n8 console=tty1 loglevel=1 no_console_suspend fsck.repair=yes net.ifnames=0 elevator=noop hdmimode=custombuilt cvbsmode=576cvbs max_freq_a53=1896 max_fr…

Hi Can anyone provide information about how to overclock and to what values in TwisterOS? Cheers JB

Is it possible to read the serial number on NanoPI R2S ? In the kernel log, there is a line: [ 4.171269] friendlyelec-board board: Serial : 7e088f783b44571e I am not sure this is the serial number, I can not match it in any way with the number on the sticker attached to the the board itself (10407692 )

Hello! I have Armbian running on a Lime2. It runs from the microSD. The board has eMMC and I have also connected a SATA SSD through USB because I would like to move the system to the SSD. I have tried doing so through the nand-sata-install.sh script but it always shows the following message: There are no available partitions. Please create them. I get that message no matter if I choose to have the boot partition on eMMC or on microSD. And I don't know much about partitions. What partitions should I create? Where should I create them? How should I create them? Thank you!

Hi, I've got an Odroid HC2 with Armbian Buster and OMV on it, and the SD card I used it with got corrupted. So I salvaged all the files from it and backups, and restored the whole file structure onto a new SD card, with an ext4 MBR primary partition. Now, my concern is, how can I make this bootable? I can boot the HC2 off a throwaway newly installed Armbian, and access the target SD card through a USB card reader. I could google that armbian-config is used to install the bootloader, but apparently it can only do that to the card which has been used to boot the device in the first place. Any suggestions? thanks

I have installed latest Armbian Buster Linux orangepi3 5.10.16-sunxi64 #21.02.2 SMP Sun Feb 14 21:17:31 CET 2021 aarch64 GNU/Linux Than I have complied ffmpeg 4.3 from https://github.com/Kwiboo/FFmpeg/commits/v4l2-request-hwaccel with parameters ffmpeg version 9236ad7-Kodi Copyright (c) 2000-2020 the FFmpeg developers built with gcc 8 (Debian 8.3.0-6) configuration: --extra-libs='-lpthread -lm' --bindir=/root/bin --enable-gpl --enable-gnutls --disable-libaom --enable-libass --enable-libfdk-aac --enable-libfreetype --enable-libmp3lame --enable-libopus --enable-libdav1d --enable-libvorbis --enable-libvpx --enable-libx264 --enable-libx265 --enab…

Hi there, I would like to have a Docker container accessing the GPIO on the Orange Pi Zero. For the time being, I'm using OPi.GPIO as a library to make a LED blink, but will use Java-Periphery and SSD1306 later on. As for now, the LED is blinking, all is fine. What I would like to do now it to create a Docker image from Armbian doing the same thing, so I was thinking of starting the image from scratch with Armbian root directory. How could I find/make a minimal Armbian root directory to build my Docker image upon? Thanks.

Hi, I am running armbian on a RockPi4 C with a penta-sata hat and OMV5 - I am unable to upgrade the kernel , other than this the system is stable apt upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: linux-image-current-rockchip64 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. Need to get 0 B/39.9 MB of archives. After this operation, 19.5 kB of additional disk space will be used. Do you want to continue? [Y/n] y (Reading database ... 61066 files and directories currently…

In the newest image "Armbian_21.02.1_Rockpro64_focal_current_5.10.12_desktop.img" I downloaded the "Armbian config" the Source download choice box does not have the version "5.10.12" as a choice. The "headers" option does download the proper version. How do I get the source for it?

Hi, after apt upgrade, armbian-zsh package is upgraded and breaks ZShell on Armbian Focal Desktop. During initial setup of Armbian on Odroid C4, zsh has been selected as default shell. After recent upgrade of armbian-zsh package, shell is switched back to bash w/o notice. Unfortunately, armbian-config is not able to switch between shells, so I am stuck with bash and cannot return to zsh. Is there a way to switch between the shells manually and enable some kind of debug log to see what is going wrong switching shells? BTW: Switching between bash and zsh on a clean recent Armbian Focal Desktop installation is also not possible. So th…

My OTG port is not functioning

Im trying to boot from network with ORPI-One-Plus, but seems to be no support for boot direct from u-boot. is possible to boot (kernel, uboot) from sdcard, and leave only / (root) on NFS? When i try to compile/boot only u-boot-sunxi-with-spl.bin

So I am in school and worked with CENTOS with these two command to save iptables iptables-save > /etc/sysconfig/iptables service iptables save I have tried googling and nothing seems to be armbian focused iptables save. Goal is to set up iptables instead of everything allowed........ armbian will be used for pi hole soon. Thank you.

I am trying to set up a WiFi access point on Hummingboard 2 which has Armbian Bionic. I am having trouble setting up WiFi AP on the HummingBoard 2. I was able to set this up in a Raspberry Pi using a combination of hostapd and dnsmasq, but having issues on Hummingboard 2 and Armbian. We are operating a sensor using the Board and would like to transfer files using the WiFi generated by the board. /etc/rc.local has the following: sleep 5 rfkill unblock wifi /usr/sbin/hostapd /etc/hostapd.conf systemctl restart dnsmasq iptables-restore < /etc/iptables.ipv4.nat NetworkManager.conf has the following: [main] dns=defau…

Hey everyone, I am using a odroid c2 board with Armbien Buster image. I have a cheap bluetooth dongle and a usb sound card connected to the board. I am trying to use the board as bluetooht to aux input for my car. The board is working as expected when the a2dp profile is in use. But as soon as i place or receive a phone call i am getting garbage sound(garbage meaning a bunch of click like sound) after a while my phone drops the bluetooth connections and gives the sounds to earpiece on the phone. Also when the phone call places my syslog gets filled with "Bluetooth: hci0: SCO packet for unknown connection handle 0" I am using bluez5, alsa and pulsea…

Hello! For some weeks now my BPM1 behaves a bit strange concerning video output. I used to connect my Banana to my monitor via a HDMI-DVI cable, which worked well for a very long time. Now, when I reboot the system, my monitor says "no signal", when I use that cable, as it does also when I use a pure HDMI-HDMI cable. The only way to make the Banana's video output work, is by using a HDMI-DSUB converter. But here comes the even stranger mystery: after I booted the Banana, using that converter, I can change the cable to whatever I want: HDMI-HDMI or HDMI-DVI, they both suddenly work again! But if I reboot the Banana again, not using the H…

I have an OrangePi PC and a BananaPi M1, and both of them are able to switch to USB host mode or device mode by editing dr_mode in corresponding .dtb file. But seems that both board are not able to support HNP protocol. From my understanding, OrangePi PC and BananaPi M1 only has perpherial-only OTG, please correct me if I am wrong. Is there any board that can support HNP? I need something that can switch USB mode(from host mode to device mode or the other way around) without reboot the board Any advice is appreciated

Hello, Please help with this issue: No Сapture selection in alsamixer or amixer. root@cubieboard2:~# arecord -l **** List of CAPTURE Hardware Devices **** card 1: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0] Subdevices:1/1 Subdevice #0: subdevice #0 root@cubieboard2:~# amixer -c 1 sget 'Line Boost' Capabilities: volume volume-joined Playback channels: Mono Capture channels: Mono Limits: 0 - 7 Mono: 7 [100%] [9.00dB] root@cubieboard2:~# amixer -c 1 sset 'Line Boost' cap amixer: Invalid command! root@cubieboard2:~# …

Hello everybody, im running a Helios64 with most current Debian Buster5.10.16 image. I was freshly setting up the device and i am now failing to assign a static ip address to it. I installed Pi-hole, Home assistant and openmediavault over softy. During the pihole installation i can setup a static ip address, but after a reboot i still get the old DHCP addess. I assigned it over the OMV interface but its not applied after a reboot, the armbian-config tool doesnt open when i want to change to static and i also tried netplan. DHCP is also turned off on my router and switch. i rebooted all of the devices mult…

Hello, I need to use the UART interface ttyS0 to connect other hardware, so I would like to disable its debug function, removing the console output that is directed to it. I've tried this: I commented the following line in /boot/boot.cmd: #setenv console "both" And compiled: mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr I was not successful, could someone instruct me on how to do what I want?

No sound is output from the line out (Orange Pi2+). An ordinary old VGA monitor is connected to Hdmi via an Hdmi-Vga adapter. Alsamixer line-out volume 100% (no MM!). Armbian-config checkerd System->Hardware->"Analog-codec" and "CIR". I run ...but nothing... Here is the output of the commands: aplay -l **** Список PLAYBACK устройств **** карта 0: Codec [H3 Audio Codec], устройство 0: CDC PCM Codec-0 [] Подустройства: 1/1 Подустройство №0: subdevice #0 карта 1: allwinnerhdmi [allwinner,hdmi], устройство 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [] Подустройства: 1/1 Подустройство №0: subdevice #0 amixer Simple mixer c…

Hi, I’m running Armbian 20.11 on a RockPro64. I have a Dell DW316 CD/DVD drive and would like to use it to burn data CDs, however so far I have not been able to get it to work. I have tried to burn using Brasero, KD3 and others but no luck. The Brasero log mentioned something about ‘adapter’ error but have tried a different USB cable. I was having an issue with ejecting media in the GUI with Armbian but managed to fix that but makes no difference for this (https://forum.armbian.com/topic/16863-failed-to-eject-media-warning/?tab=comments#comment-117961). The Drive makes a whirling noise for a few seconds then stops and does that repeated…

Hi all, I played around with home assistant on my Odroid HC1 (running NCP as main task) and now wanted to remove home assistant completely because I don't need it anymore. I tried to uncheck the software in Softy but that doesn't have any impact. How can I completely remove home assistant? Thanks!

Hi I would like to use the UART on physical pins 3 and 5 (https://wiki.radxa.com/RockpiE/hardware/gpio) Does anybody know how to activate it? There is an overlay uart4 but it doesn't do what I expected it to do :-) Thanks Chris

Hi ! I spent several hours looking for the solution, here and elsewhere, I didn't find. The Radxa wiki speaks about 2 SPI: 1 and 2 The device tree README speaks about 4 SPI: SPI 0 pins (MOSI, MISO, SCK, CS): GPIO3_A5, GPIO3_A4, GPIO3_A6, GPIO3_A7 SPI 1 pins (MOSI, MISO, SCK, CS): GPIO1_A7, GPIO1_B0, GPIO1_B1, GPIO1_B2 SPI 2 pins (MOSI, MISO, SCK, CS): GPIO1_C0, GPIO1_B7, GPIO1_C1, GPIO1_C2 SPI 3 pins (MOSI, MISO, SCK, CS): GPIO2_B2, GPIO2_B1, GPIO2_B3, GPIO2_B4 So, the correspondence seems to be: radxa SPI 1 <=> DT SPI 1 radxa SPI2 <=> DT SPI 3 With the latest kernel (5.10.12-rockchip64, Deb…

Dear all, My system logs: http://ix.io/2Pgj I consistency get a crash with dtc on both orangepi, nanopi neo+2, nanopi neo3 when I try to see the current devicetree via the filesystem, e.g.: $ dtc -I fs /sys/firmware/devicetree/base/ <stdout>: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name <stdout>: Warning (clocks_property): /soc/spdif@1c21000:clocks: cell 0 is not a phandle reference <stdout>: Warning (clocks_property): /soc/spdif@1c21000:clocks: cell 2 is not a phandle reference .... /dts-v1/; / { [1] 16929 segmentation fault dtc -I fs /sys/firmware/devicetree/base/ …

I have a Retro-bit gamepad but it does to seem to be detected in Twister OS, any one know of what is supported or what I need to do to get mine working?

NanoPi M4v2 with official NVME hat kit, boot from EMMC with OS: Armbian w/ Debian Bullseye, Linux 5.10.12-rockchip64 SSD: Kioxia XG6 (Thinkpad part) That also happened with 5.9 kernel. Not tested with other OS. When doing cold boot, always got kernel messages like: Feb 11 01:14:34 localhost kernel: [ 3.102606] nvme 0000:01:00.0: enabling device (0000 -> 0002) Feb 11 01:14:34 localhost kernel: [ 3.106554] input: gpio-keys as /devices/platform/gpio-keys/input/input0 Feb 11 01:14:34 localhost kernel: [ 3.107121] of_cfs_init Feb 11 01:14:34 localhost kernel: [ 3.107161] of_cfs_init: OK Feb 11 01:14:34 localhost kernel: [ 3.129048] dw…

Dear all, I'm frequently losing GPIO interrupts on various boards, which seem to be caused by bursty processes. When I shield the cores that have those interrupts according to /proc/interrupts with e..g. "cset shield --cpu=0,1" , way less interrupts are lost (e.g. for 4kHz interrupts one in hours instead of once per minute). Most of these (ADC) interrupts are handled by my own kernel module, but couldn't find how to restrict them to e.g. CPU0, and they are not movable using /proc/irq/*/smp_affinity. HomeCT1:~:% grep ads /proc/interrupts 66: 166559 0 0 0 sunxi_pio_edge 1 Edge ads131a04 162: 27…

nanoPi M4 running Armbian 21.02.1 Buster with Linux 5.10.12-rockchip64. Attached are two identical B25 USB Bluetooth Transmitter Sticks which are supposed to transmit the same MP3 stream (provided by Mopidy or Shairplay Sync). The following screenshot shows just a single B25 stick attached, the second one has yet to arrive. I expect them to all have the same USB ID ID 0a12:1004: Here’s the problem: After each reboot the system (or ALSA?) gives the B25 stick a different card number in aplayer -l (in the screenshot above B25 is card #2, on the next reboot it could switch position and be #1). Question therefore: How can I make two id…

I'm trying to run NixOS on my NanoPC-T4, and it's having trouble detecting the NVMe drive connected to the M.2 port. I've tried running Armbian, specifically Armbian_21.02.1_Nanopct4_focal_current_5.10.12.img downloaded from here, and it appears to detect it just fine. On NixOS I'm running a stock 5.10.13 kernel, which is newer than the 5.10.12 that Armbian is using. I'm assuming that I'm missing some kind of specific patch that makes this work on Armbian. I examined the kernel I was running on Armbian: qwe@nanopct4:~$ ls -l /boot/ | grep rockchip total 63872 -rw-r--r-- 1 root root 221399 Feb 3 19:55 config-5.10.12-rockchip64 l…

I failed my password attempts (5 times) a few days ago. The account is still not allowing for a login. I have attempted to remove the password from /ect/shadow but I am still getting prompted for a password, so either I didnt do it right or it didnt save.

Hello. I am a real newbie at Linux and so I really need your help. I set up a new odroid N2+ with Open Media Vault, and it doesn't show anything. I'm assuming that the id/password I used wasn't the admin id/password. So, I used Putty to get into my new machine, and I used the following to change the password of "root": root@odroidn2:~# passwd root New password: Retype new password: passwd: password updated successfully root@odroidn2:~# exit However, I couldn't sign in to OMV with that id:root and the password that I just changed it to. Does anyone know what I'm doing wrong? (Please excuse the basic ignorance of this quest…

Hello! I have a stash of OPi H3 boards and it just occurred to me that there's no way to interface them with a storage device in any decent way. What am I missing here??? I also have a lot of 100 GB SATA SSD's, and I thought to myself, wouldn't it be great if each SBC could have its own SSD. But then I realized... how the hell am I going to get any kind of decent IO? If it's not possible with SSD's connected locally, let's forget them and then think, what other storage device can I use so that my OPi boards have some respectable IO device to work with? Please tell me where the gap in my understanding is?! Thanks!

Goodmorning, I'm Tiziano from Italy. I would like to manage all the delicate functions of my reef aquarium through an Orange Pi Lite card. I saw that both the Armbian Buster program and the Armbian Focal program are available for my card, I kindly ask you to understand if there is a fundamental difference between the two and which. I have tried successfully in any case to install and run both programs on the microSD and to start the two programs. The card starts up and the whole procedure is performed correctly. The problem is that in the end I am only asked to choose the "default system command shell" between "bash" and "zsh", no option to start a desktop …

Hello, I am using Armbian 21.02.1 Focal with Linux 5.10.12-sunxi (Armbian Focal from https://www.armbian.com/orange-pi-zero/). I use the default logrotate configuration (ratate logs in /var/log) but I have a problem that the /var/log/syslog file is still growing (even if logrotate is run daily). Currently the logrotate process takes place in 3 steps (see /etc/systemd/system/logrotate.service -> [Service] section): 1) ExecStartPre =/usr/lib/armbian/armbian-ramlog write (ramlog write files to update log.hdd before rotation) 2) ExecStart =/usr/sbin/logrotate /etc/logrotate.conf (Logrotate) 3) ExecStartPost =/usr/lib/armbian/armbian-ramlog postrotate (r…

Hi, I Would like to connect orangepi PC to 1280x1024 dvi monitor, as I used to with few years old armbian before. Tried h3disp but it reports that board/kernel is not supported. Is there some new method for that?

Hello, i have an orangpipc h3 and i'm trying to install homeassistant supervised using this script curl -sL https://raw.githubusercontent.com/home-assistant/supervised-installer/master/installer.sh | bash -s and i get the error [error] missing: apparmor so i ran armbianmonitor -U and i get AppArmor: AppArmor disabled by boot time parameter Is it possible to enable apparmor? if so how do i do that? i tried searching the forum for the same message but it appears in a lot of posts simply when ambianmonitor is pasted.. which reminds me.. Spoiler 1 2 ### Activated 1 lzo zram swap devices with 499 MB each 3 …

Hello there, I am using Armbian 20.11.6 Buster with Linux 4.4.213-rk3399 on a Nanopi M4V2, I have connected 3 SATA HDDs and use mdadm (for a RAID 5 Array of those drives), luks lvm and ext4 (in that order, more details below) to store my backups. `armbianmonitor -u` link: http://ix.io/2NYv Recently I have received errors in borg backup, about mismatching checksums. To confirm that this error is not a borg specific error, I wrote this little zsh script to write data and generate checksums. for ((i = 0; i < 100; i++)); do dd if=/dev/urandom bs=4M count=256 | tee $i | md5sum | sed '/^a/!s/.$/'"$i"'/' > $i.sum To be more precise…

Hello, I've the Pi One H3 version that I always used with a HDMI to VGA adapter that worked ok until lately that stopped working. So I was thinking to connect the board to a TV monitor having DVI connection. I've tried both stable and experimental version of Armbian o.s. and it shows the same problem, basically it boots ok at native resolution (1280x768 60Hz) until it starts the desktop GUI and it goes to "no signal". If I return to the text console mode the monitor feel the signal again and at the same native panel resolution. I've tried both HDMI to DVI adapter at the monitor side and also an HDMI to DVI adapter and using a DVI cable on the board side and noth…

http://www.cubietech.com/ website is available and even lists CB9 for sale ! But http://cubieboard.org/ website which provides support for CubieBoard (and O.S images) is down ! What gives ? Is CubieTech dead or alive ? Where can I find any (new or old) Linux images ? (for Cubieboard 4, specifically; I also had Cubieboard 3 / CubieTruck lying somewhere, but I can't find it anymore ...) A new Debian like v10 "Buster" or v11 "Bullseye" will support outdated Cubieboards ? Thanks in advance,

I am using Pine A64 1Gb as a development board where I am using Armbian 20.11.7 Buster with Linux 5.10.4-sunxi64 as my OS and i tried installing Numpy either directly on board through terminal or from SSH after running for few minutes it freezes and i have to power reset the board. I am using command: pip3 install --verbose numpy and it freezes after these last few lines: aarch64-linux-gnu-gcc: numpy/core/src/umath/ufunc_object.c aarch64-linux-gnu-gcc: build/src.linux-aarch64-3.7/numpy/core/src/npymath/ieee754.c aarch64-linux-gnu-gcc: build/src.linux-aarch64-3.7/numpy/core/src/npymath/npy_math_complex.c aarch64-linux-gnu-gcc: numpy/core/src/npymat…

I have the same problem on Orange Pi PC rmbianmonitor -m 12:15:42: --- 0.06 15% 4% 9% 1% 0% 0%/usr/bin/armbianmonitor: line 388: read: read error: 0: Invalid argument /usr/bin/armbianmonitor: line 389: [: -ge: unary operator expected cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepipc BOARD_NAME="Orange Pi PC" BOARDFAMILY=sun8i BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=fef01045-dirty DISTRIBUTION_CODENAME=bionic DISTRIBUTION_STATUS=supported VERSION=20.11.6 LINUXFAMILY=sunxi BRANCH=dev ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMGE_TYPE=Image

Hello. I'm running "Armbian 20.11.6 Focal" on an Odroid-C2 board. Today, after an "apt-get update" and "apt-get upgrade", the OS name changed from "Armbian 20.11.6 Focal" to "Ubuntu 20.04.2 LTS". The changes has been done from the package "11ubuntu5.3" (https://launchpadlibrarian.net/519827877/base-files_11ubuntu5.2_11ubuntu5.3.diff.gz) on the files "/etc/issue" and "/etc/issue.net". Well, is that a problem under an "Armbian" point of view? Should I replace "Ubuntu 20.04.2 LTS" with "Armbian 20.11.6 Focal" on the files "/etc/issue" and "/etc/issue.net"? Thanks.

I'm using Buster on the Neo3 but am having an issue using an MT7610 USB wireless NIC. I believe the 7610 is on the list of supported devices, so am not sure if I'm hitting an issue with the build? Image Info: Armbian_20.11.10_Nanopineo3_buster_current_5.9.14.img.xz Error message from dmesg: [ 385.819703] usb 4-1: new high-speed USB device number 4 using xhci-hcd [ 385.983275] usb 4-1: New USB device found, idVendor=0e8d, idProduct=7610, bcdDevice= 1.00 [ 385.983299] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 385.983314] usb 4-1: Product: WiFi [ 385.983330] usb 4-1: Manufacturer: MediaTek [ 385.9…

Dear all, I used win32diskimager to write the armbian image on a 8G sd card and everything works good. when I finish working on the image I read the final image also by using win32diskimager, the size of this image is right now 8G since the sd card size is 8G. After that I wrote this 8G image on a 16 G sd card. when I check the size of this new sd card after writing the 8G image it shows that the sd card size is 8G not 16 G. So, please how can I read an image from a 8G sd card and write it to a 16 G sd card and the size of the sd card remains 16 G to be used later. Best regards

Hi! Can someone point me to a tutorial/documentation on how to setup a DS3231 RTC module on Armbian Buster? I'm currently using a Tinker Board S with Armbian 5.9.14. My RTC is correctly connected to my board. It is detected: sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- 68 -- -- …

Hi All, I have a RockPi4B and am using Armbian buster 5.9.14 downloaded from the RockPi page. One of my main motivations for getting the RockPi4 was its hardware AES capabilities. I can confirm this via $ grep aes /proc/cpuinfo Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid Features : fp asimd evtstrm aes pm…