Allwinner sunxi

Hi, I am building small file server. Is it possible to boot from mmc AND have data on sd card without the need of removing sd card on every reboot? I've installed armbian on smaller sd card, used nand-mmc-* script to write armbian onto mmc. Now, everytime I reboot I need to remove sd card, wait for system to load and put sd card back. I edited .fex file, setting sd card mode to 1, but it didn't helped. Any ideas/manuals on that? Thank you in advance.

Hello, I am just trying to set up a pcduino3 nano with Debian Jessie. I downloaded 4.9.7 and put it onto SD card, booted, logged into my sudo account, and then apt-get install lightdm followed by apt-get update apt-get upgrade as per "Getting Started" guide. I now have 4.9.12 LIghtdm fails to start with following message: systemctl status lightdm.service -l ● lightdm.service - Light Display Manager Loaded: loaded (/lib/systemd/system/lightdm.service; enabled) Active: failed (Result: start-limit) since Tue 2017-03-07 21:41:18 CET; 17min ago Docs: man:lightdm(1) Process: 1460 ExecStart=/usr/s…

I am using the latest Armbian image on OPI+. I had a requirement to read a 64Gb USB flash formatted under Windows with the extFat filesystem. Much to my surprise it didn't mount. I thought it was a hardware problem 1st. But then it appeared, that mount doesn't support the the extFat filesystem by default. It is necessary to add the extra packages, but I didn't succeed: root@orangepiplus:/# apt-get install exfat-fuse exfat-utils Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: exfat-fuse exfat-utils 0 upgraded, 2 newly installed, 0 to remove and 9 not…

Hi, I just saw ARMBian has been upgraded to 5.00 version. Then I though to check if my initial problem (for my first ARMBian test with the previous 4.5 version) could be solved with this new version : http://forum.armbian.com/index.php/topic/616-lamobo-bpi-r1-network-issue-sudden-reboot-quick-usb-uart-how-to/?hl=miguipda What I encounter now with the 5.0 is a Lamobo R1 seems stable because no blinking green led. Just keep the red led switched on and wan with lan usable (I may contact website like you now ;-) ). Even with the connected harddrive. But... As my modem has the IP 192.168.1.1 and says that two IP are distributed with DHCP I saw the 192.168.1.4 …

Hello! I wrote the legacy image to a sd card and put it into the card slot. I can see something like diagnostic message and then "starting kernel". After that there is no video output. Neither over VGA nor over HDMI. Is that wanted? I tried 3 different monitors, but no chance. I can connect via ssh after a few minutes, but using a monitor and a screen would help, when there is no network. What am I doing wrong? Greetings, Pille

I have dd'd Armbian "stretch" onto a 16GB SD card and it's booting my CubieTruck fine. But I have no clue how to move it from there (mmcblk0p1) to my attached 128GB SSD (sda1). I've tried the nand_sata_install shell script but it appears to be a bit old (2 years), created a bunch of weird temp directories: root@cubietruck:~# df -h Filesystem Size Used Avail Use% Mounted on udev 939M 0 939M 0% /dev tmpfs 202M 4.0M 198M 2% /run /dev/mmcblk0p1 15G 1.1G 14G 8% / tmpfs 1006M 0 1006M 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 1006M 0 1006M 0% /sys/fs/cgroup tmpfs …

Hello, Is there a guide / tutorial on making Kodi run with hardware acceleration enabled on Armbian on Orange PI PC Plus? e.g. like how LibreELEC does it. I have found a bunch of information on different sites and forums, but I can't put it all together. What I know so far: * Apparently the HW-accelerated decoding is supposed to be done on Kodi's side via VDPAU API * The Kodi build in Armbian repos does not have built-in support for libvdpau (?) * ffmpeg, the video decoding library used by Kodi, doesn't support Allwinner GPU out of the box and needs patching * Kodi needs to be re-compiled with the patched ffmpeg vers…

Hello everyone, I need use gpio pins in my Orange Pi Zero. I found the pyA20 library: orangepi_PC_gpio_pyH3: https://github.com/duxingkei33/orangepi_PC_gpio_pyH3... I bought the DHT11 sensor, but I could not get it to work in any way. Is there anyone working on this subject? For example, my code block: #!/usr/bin/env python from pyA20.gpio import gpio from pyA20.gpio import port from pyA20.gpio import connector from time import sleep def bin2dec(string_num): return str(int(string_num, 2)) data = [] #GPIO.setmode(GPIO.BCM) PIN = port.PA6 gpio.init() gpio.setcfg(PIN, gpio.OUTPUT) gpio.output(PIN,gpio.HIGH) sleep(0.025) gpio.output(PIN,gpio.LOW) sleep(0.02…

I tested with Armbian Stretch image on NanoPi-NEO-Core2. PJSIP VoIP Client. MIC input does not work. Additional USB sound cards work well. In FriendelyARM original firmware, MIC input works well. I hope that this issue will be resolved. Please help me.

I am using a orangepi win plus. I have attached a ssd1306 OLED display to the board, using i2c1 interface, using the luma.oled library as driver. import sys from PIL import Image from PIL import ImageDraw from PIL import ImageFont import subprocess from luma.core.interface.serial import i2c from luma.core.render import canvas from luma.oled.device import ssd1306, ssd1325, ssd1331, sh1106 from time import sleep serial = i2c(port=1, address=0x3C) device = ssd1306(serial, rotate=0) width=device.width height=device.height image = Image.new('1', (device.width, device.height)) # Get drawing object to draw on image. draw = ImageDraw.Draw(image) # Draw a black filled…

Hello i've updated the kernel from the legacy to the dev using the procedure To make sure you won’t run into conflicts within newly installed packages, remove them all before upgrade: 1 2 aptitude remove ~nlinux-dtb ~nlinux-u-boot ~nlinux-image ~nlinux-headers aptitude remove ~nlinux-firmware ~narmbian-firmware ~nlinux-$(lsb_release -cs)-root Proceed with install: 1 2 3 4 …

Hi I want to install a tv-server (vdr) on my orangepi with a usb-dvb-stick from astrometa. I read this post and try to reproduce it. I build my own image ARMBIAN 5.27 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i (linux-sun8i-default.config )and install v4l driver with no errors. Unfortunately it don't work. The system don't recognize the stick (see file orangepi_Astrometa.txt and dmesq_media_build.txt ). Useful for comparison my raspberrypi with the stick (raspberry_Astrometa.txt) . Can anybody help? Ciao nepo

hi all, i had a orange pi zero board that worked fine until yesterday. MY BOARD IS ORANGEPI ZERO (not 2) i upgraded the OS armbian : Linux orangepizero 6.6.31-current-sunxi #1 SMP Fri May 17 10:02:40 UTC 2024 armv7l GNU/Linux the board worked fine until the last reboot in order to test octopi startup, but before this reboot the OS was upgraded and rebooted the issue now is that the wlan0 seems to be always down i do a lot of setup but it still to remain down, i am not a very expert with these board but i am very new with this kind of issue. can anyone help me with the troubleshooting ? …

Hi everyone! That's getting me off... I though it was plug&play but didn't, Anyone can help me giving me the solution to this problem? Thank you very much Kind Regards

Hello, I have lubuntu installed on Cubieboard 2's NAND and I want to test Armbian. I've downloaded Armbian_5.10_Cubieboard2_Ubuntu_trusty_3.4.112 and write the image on a SD card using sudo dd if=Armbian_5.10_Cubieboard2_Ubuntu_trusty_3.4.112.raw of=/dev/rdisk2s1 But the cubieboard does't boot from the SD card, I get these error messages

Hi i have a problem trying to load the drivers of this camera, could you help me? Issue: mobprobe: FATAL: Module ov5647 not found in directory /lib/modules/4.14.84-sunix Board: Orange Pi Lite Camera sensor: OV5647 fisheye OS: Ubuntu - Armbian 5.65

Hello there. I'm owner of nano pi m1 board. I want use hid usb gadget on this board, but no success. First I use prebuild image from download section. I fugured out, that the image contains android_usb gadget and it's works (i didn't go deep, but i see, that after some manipulations with files my computer see nano pi as mass storage). Ok, this shows that nanopi board can be used as device. Go next. I need to load g_hid module, but there is no such module in the default image. Ok, time to compile custom kernel (with Igor's script this is easy). I included hid usb gadget via menu. Booting and "modprobe g_hid". Failed. "No such module" turns into "No such device". Hm...…

Hello there. I've got an Orange Pi PC+ SBC running desktop Armbian Xenial 5.38 kernel 3.4.113 from its eMMC that showed up pink screen after intermittent Power Up. I was using a 5V power adaptor that became faulty and intermittently became on and off. After replacing the power adaptor and booting up my device to a HDMI monitor, I found out that it now displays nothing but pink screen! Here's what I've done to no avail: 1. Turning on the HDMI monitor before and after I turn on the machine 2. SSHing from UART0 and suing command h3disp -m 5 (or 6 or 33 or 34...). No dice 3. Booting using the same Armbian OS but from SD card. SSH shows me the hostn…

Previously worked, but not now. I am stuck in the login line and cannot login with the keyboard from the putty screen. I cant login with keyboard on USB2. Also HDMI not working. HDMI previously worked too. I am newbie. Thanks in advance. I cant remember which version loaded on the eMMC. U-Boot SPL 2019.04-armbian (Jul 06 2019 - 20:55:41 +0200) DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: BL31: v2.1(debug):bb2d778-dirty NOTICE: BL31: Built : 20:55:33, Jul 6 2019 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: BL31: Found U-Boot DTB at 0xc079e78, model: OrangePi 3 INFO: ARM GICv2 driver initialized NOTICE: PMIC: …

hello after updating from cat /proc/version Linux version 4.14.84-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #3 SMP Sat Dec 1 07:18:41 CET 2018 to Linux version 4.19.13-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #5.70 SMP Sat Jan 12 15:43:21 CET 2019 my one wire thermometer stopped working - is there some additional steps needed now? I didn't change my configuration overlays=w1-gpio param_w1_pin=PB10 param_w1_pin_int_pullup=0  and now I have dmesg [ 1174.451457] w1_master_driver w1_bus_master1: Attaching one wire slav…

I notice there is a 16mb spi flash on the bottom of my orange pi zero. I read it is possible to boot off it. Has anyone done it, and is it useful? Is it possible to run without the sd card? I am interested in locking the sdcard to read only for reliability during power loss, and storing application configuration data to the spi flash if possible. Can it be mounted with a filesystem, or is it better to use a ramdisk and store it periodically to flash?

Hi, I'm trying to run a DHT22 Temperature & Humidity sensor on my Cubieboard2 but I seem to fail at the beginning on how to use the GPIO Pins correctly What I have: Cubieboard2 Armbian Linux version 4.11.6-sunxi (root@devel) (gcc version 7.1.1 20170510 (Linaro GCC 7.1-2017.05) DHT22 (worked on a Raspberry Pi3 before) What I've done so far: According to this Overview (http://docs.cubieboard.org/cubieboard1_and_cubieboard2_gpio_pin) I connected the sensor on 3v3, GND and on PD25 (LCDDE). As far as I understood the LCD pins can be also used for other things. Followed "Accessing the GPIO pins through sysfs with mainline kern…

Hello, I'm running a banana pro on the last armbian without any issues on a 16 gb SD Card. I wanted to make a try on a 64 gb card and burn the image on it, I think something went wrong, but now I cannot format or burn anything on the SD card, it says that the media is write protected. I tried to wipe out using parted or some tutos I saw creating an additional Registry key, but nothing worked ! Is my SD broken ? Thanks Greg

As per the title, I am using the 5.05 Jessie Server image on a OrangePi PC. Every time I shut it down (shutdown -h now) when I power it back up I get errors reading the SD card and it wont boot. I have tried 3 cards, all with the same issue, I can reboot the device with issue and a fsck is clean after every reboot. I do not have a linux machine to scan the card after a power off, so can't check it after it fails. Does anyone have any ideas?

Hi to all, sorry if it is already described anywhere. I found some similar issues but no solution, except ...has to be modified.. or anything similar. Two days ago I updated my Armbian Jessie server on may Cubietruck with apt-get update && apt-get upgrade After that my homeautomation didn't show the SoC temperature any more. first I looked for an error in the software, then after a lot of reboots I noticed the temperature also missing in the armbian startscreen. The command cat /sys/devices/virtual/thermal/thermal_zone0/temp was responsed by cat: /sys/devices/virtual/thermal/t…

Hello, I have Orange Pi One Plus with the kernel 5.15.80 of Armbian 22.11.1 and work well. , but after upgrading to 23.8.1 kernel 6.1.47 the network interfaces stop working at all. Even I try the 23.05.1, 23.05.6 all have same error which because the kernel is 6.1.x. Currenly I limited the internet access without the the network. May I know how to fix it in the console or someone can help to generate the 23.11.1 image for fixed this error. Thanks The error message like as below in the console terminal. [ 9.899195] dwmac-sun8i 5020000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19) The spec of …

Hello, I have started on Armbian Ubuntu on a Orange Pi PC and have some difficults to follow the tiny font on the terminal emulator. In order to change the fontsize, I used the command "dpkg-reconfigure console-setup" and choosed the Terminus font with a bigger size. But no effect after reboot. With which trick a modification can be performed? What is with the fonts marked with "framebuffer"? If a modification is not possible with the Armbian terminal emulator, can I use an alternative? So I miss a property button as available on Raspian. Thanks for yor help and best regards Walter

Greetings, I recently purchased an Orange Pi Zero for the purpose of Pi-Hole. I have been running Pi-Hole on a Raspberry Pi-1 under Jessie and the stability was great. I never had to worry about it. However, with Orange Pi Zero, running Armbian/Jessie as well, I get a maximum of 2 days of up-time. This is a standard armbian/jessie installation with only pi-hole installed. Since there is no video output (I did not purchase the extension board), I had to perform a power-off/on. Without ruling out the possibility of hardware fault (SD card or USB power supply), does anyone have stability problem of Armbian/Jessie on Orange Pi Zero? …

Using Nanopi neo. Linux Lap 3.4.113-sun8i #4 SMP PREEMPT Wed Nov 22 13:45:28 CET 2017 armv7l GNU/Linux I've tried both the Jessie and Ubuntu versions on the site and tried changing the the kernels to 4.x with the next and dev versions. I get similar results in each. Tried to upload diagnostics but got server error I have an IP camera connected directly to the ethernet port with static IP on both the camera and the port. I ssh to the nanopi via wifi. The wifi port is forwarded to the ethernet connection so I can get images from the camera. The ethernet connection seems to drop at random intervals but the time that it down/up are…

Hello I received my first OrangePi today, a Zero, and I'm a bit lost. Installed armbian xenial, upgraded to beta/dev and installed dev kernel as documented. (working!) But after this upgrade only one CPU core is in use. I've searched, and think my problem may be uboot, can anyone point me in the right direction? (is there a working 4.x kernel with quadcore support?) Thanks! Info: olekvi@orangepizero:~$ uname -a Linux orangepizero 4.9.0-sun8i #16 SMP Fri Jan 6 05:03:52 CET 2017 armv7l armv7l armv7l GNU/Linux olekvi@orangepizero:~$ cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 5 (v7l) BogoMIPS : 48.00 [..] o…

So I have been struggling with my new Orange Pi Zero the last couple of days, I tried everything but was unable to get it working. I followed all debugging steps I could find through google and through this form so i am at the end of the rode. I have tried 2 different SD cards, on which I ran h2testw 1.4 with the following result: Spoiler Card 1: Test finished without errors. You can now delete the test files *.h2w or verify them again. Writing speed: 20.3 MByte/s Reading speed: 63.9 MByte/s H2testw v1.4 Card 2: Test finished without errors. You can now delete the test fi…

# uname -a Linux H6 4.18.13-sunxi64 #3 SMP Fri Oct 12 17:43:44 CST 2018 aarch64 GNU/Linux 1, burn the image to SD card 2, use nand-sata-install command, burn emmc 3, remove the SD card 4, reboot the board, can't boot, the error message: U-Boot SPL 2018.09-rc1-armbian (Oct 12 2018 - 17:39:13 +0800) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### root@H6:/mnt/emmc# fdisk -l Disk /dev/mmcblk0: 30 GiB, 32218546176 bytes, 62926848 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physic…

Ununtu 14.04 in a VirtualBox VM Latestes Armbian ./compile.sh BOARD=orangepiplus KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=wheezy KERNEL_CONFIGURE=yes KERNEL_KEEP_CONFIG=yes COMPRESS_OUTPUTIMAGE=no BUILD_DESKTOP=no ..... [ o.k. ] Installing packages for [ Armbian ] Reading package lists... Building dependency tree... Reading state information... E: Unable to locate package f3 [ error ] ERROR in function create_rootfs_cache [ debootstrap-ng.sh:245 ] [ error ] Installation of Armbian packages failed [ o.k. ] Process terminated [ error ] ERROR in function unmount_on_exit [ debootstrap-ng.sh:539 ] [ error ] debootstrap-ng was interrupted …

Hi, As I saw some people were able to use docker on CubieTruck : https://dzone.com/articles/cross-platform-hybrid-cloud https://dzone.com/articles/big-data-processing-arm-0 As there are also some images for Raspberri/docker like http://blog.hypriot.com/getting-started-with-docker-on-your-arm-device/and as in the changelog of the kernel, docker is mentionned, I would like to know how to install & use docker on my cubietruck. Did someone achieve that ? I'll be quite interested to do a docker cluster of my Rasp & Cubietruck for my self hostiing needs Maybe this could help too : https://github.com/umiddelb/armhf/wiki/Installing,-running,-using-docker-on…

Hi all, Creating a DietPi image for BPi Pro based on ARMbian. I finally got a chance to test do_expand_rootfs() from /etc/init.d/firstrun. Now works with multiple partitions, thanks for doing that Having an issue with the onboard WiFi on the BPi Pro (Lemaker). It appears to be enable, active and ready for use, however, I can not get it to scan/connect to a SSID, or even work in AP mode. Built the image using your excellent build tools: [ o.k. ] Building [ Armbian 5.17 Bananapipro Debian jessie default ] root@DietPi:~# iwlist wlan0 scan wlan0 No scan results Fails to set country code. Always returns 00. root@DietPi:~# iw reg set GB root@Die…

Hi, Can someone help me on how we can set a uBoot splash screen (with a .bmp) instead of the running boot text? Need this in a OPiPC, legacy (3.4.113). Any help is welcome. Christos

Hi I have an Orange Pi PC running "ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.113-sun8i". Can I update to Armbian Strech kernel 4.14 directly without lose of data and configurations? How can I do it? Thanks.

Hi, do you remember my issue with 2 opi1? Well, today I burned again an armbian image with etcher and connect either of the two opi one, to a usb-ttl converter (an arduino). ok, when I put the power on the result is what you see in the attach... the two freeze on DRAM: always. the power is a xiaomi power adapter 5v2a (double checked with a multimeter) and a handmade cable (checked with the multimeter too, 4.8v/4,9v always) so...can I finally tell that my two board are faulty? or there is something I could do? thank you in advance

When installing snaps I get the following error: error: system does not fully support snapd: cannot mount squashfs image using "squashfs": mount: /tmp/sanity-mountpoint-910419852: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error. It worked about a mouth ago but now whenever I build the images and try to install a snap I get that error. Steps to reproduce: 1. Build Nanopi Duo2 image with kvm and squashfs 2. Connect to device and install snapd 'sudo apt install snapd' 3. Install snap to test it 'sudo snap install hello-world' Expectation: …

Hello. I have problem with SSH on Armbian 23.8 Bookworm Orange Pi 3 LTS. Orange seems like booting ok, DHCP works too, since I see Pi's IP in my router settings, also I can ping it, and I'm 100% sure its Pi's IP since I have only my PC connected to LAN. I waited for 5 mins, and still couldn't connect to SSH. I tried to do port scan on Pi's IP and nmap says that only 5555 port is open. I am using 2A Adapter, so there should be no power issues. Here are some logs. Spoiler ping 192.168.1.82 Pinging 192.168.1.82 with 32 bytes of data: Reply from 192.168.1.82: bytes=32 time=2ms TTL=64 Reply from 192.168.1.82: bytes=32 time&lt…

Took me over a year to isolate this bug. Randomly, I have found that /boot/armbianEnv.txt had unconsistent content. Examples: .tty1tty1LOGIN.8 ¹[fU7ttyS0tyS0LOGINusbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="Demaine_40_Grd_Rue_Chambre-BP" #psk="1234567890" psk=693d195a3bf2ab6defbcc0b54604ced4286a067996138db6dc793d8648f67d79 } usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="fabste" #psk="1234567890" psk=95342031a4b28398045e1761f9c64f8454902e80d37102e5476fa…

After updating to 5.9.14 from 5.8.16, framebuffer is broken. No output after booting, hdmi monitor goes to sleep. [ 1.455763] ------------[ cut here ]------------ [ 1.455791] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:287 __arm_ioremap_pfn_caller+0x13f/0x14c [ 1.455796] Modules linked in: [ 1.455810] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.9.14-sunxi #20.11.3 [ 1.455814] Hardware name: Allwinner sun7i (A20) Family [ 1.455846] [<c010cce9>] (unwind_backtrace) from [<c010945d>] (show_stack+0x11/0x14) [ 1.455862] [<c010945d>] (show_stack) from [<c093b0ab>] (dump_stack+0x77/0x84) [ 1.455878] [<c093b0ab>]…

Hi I have added some drivers in the kernel source code in the cache folder and I am not sure how to rebuild the kernel with the new changes. I am trying to rebuild the mainline kernel. Using compile.sh overwrites the changes with default files. I have changed the following configurations in my config file. KERNEL_ONLY="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 3 KERNEL_CONFIGURE="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 4 CLEAN_LEVEL="" # comma-separated list of clean targets: "make" = make clean for selec 5 # "debs" = delete pac…

Hi, Over the last couple of weeks, I have been trying to get Pi-hole working (and more importantly, stable) on the Orange Pi (along with the relevant Orange Pi zero H2+ ARMbian OS) without success. I realize that I am using "Tested" but as yet not marked "Stable" code, however I'm hoping this can help somebody here perhaps in terms of developing a stable OS for these little boards. I have rebuilt the SD card from scratch several time now. The SD card is of reputable make (Sandisk) and in fact I have tried two different cards, just in case this was a card issue. I'm using a reliable power supply, which I have verified by continuously monitoring it with my …

So i'm using Orange Pi PC with the latest armbian desktop image. I've noticed this issues: -Booting takes a long time with wifi adapter (realtek 8188etv), stucks at "lsb raise network interfaces" for 2 minutes, than continues -Browsing shares via thunar results in this error -No chrome/midori in repos ?

I have a question ...is it possible to run : Medion X10 (WiFi) remote control ? http://www.x10receiver.net/info_supportedremotes Unfortunately, after the command irw I do not get any information ...... I'm not too good at linux :-( Armbian system detects this as a pilot ! lsusb Bus 006 Device 003: ID 0bc7:0006 X10 Wireless Technology, Inc. Wireless Transceiver (ACPI-compliant) cat /proc/bus/input/devices I: Bus=0003 Vendor=0bc7 Product=0006 Version=0100 N: Name="X10 WTI RF receiver" P: Phys=usb-sunxi-ohci-1.2/input0 S: Sysfs=/devices/platform/sunxi-ohci.2/usb6/6-1/6-1.2/6-1.2:1.0/rc/rc1/input9 U: Uniq= H: Handlers=kbd event9 B: PROP…

I've been using pyA20 as H3 gpio library in Orangepi. Recently we've moved to nanoPi M1 . But the problem is H3 on nanoPi has more gpio pins than orangePi and A20 gpio library does not recognize these pins. Is there any H3 gpio library like pyA20 available ? (Please note WiringOPI is for C not python) Thanks.

Hi.Can you help me fix this problem.Can't use usbwifi wl167g(need like reciever). Network-manager show(wifi enable) but firmware missing. Tried to install RT73_linux_STA_DRV1.0.3.6, have error, when step make, rtmp_main.c error "-march=i686". In new version desktop ubuntu wifi working, but shows slow video(I guess many improvements "use" a lot of resources).

I have OrangePi Zero (basic version without HDMI) and OrangePi PC+. However, devices came with almost no documentation, so I would like to know the pinout for GPIO pins. Is there any documentation available? BTW, I need to solder GPIO pins to OP Zero, but it is OK.

I received NanoPi NEO and NEO Air boards along with the NanoHat PCM5102a that FriendlyArm is selling: http://www.friendlyarm.com/index.php?route=product/product&product_id=169 It's a good quality audio stereo out addon board compatible with NEO and NEO Air. I got it working with Armbian on NEO Air! I adapted commits from FA's repo to match Armbian's tree and get that DAC working, (original commits here: https://github.com/friendlyarm/h3_lichee/search?utf8=%E2%9C%93&q=pcm5102a+&type=Commits). Add these to 'userpatches/kernel/sun8i-default`: https://gist.github.com/Simon-L/c8c119c86d7d3fe4316387c3ae818379 Add this config to 'userpatches' to have t…

Hello All, I'm trying to set-up MCP2515 on 8mhz on orange Pi one on SPI0 running recent installed Armbian 5.9 / Linux 3.4.113-sun8i can bus support orange pi zero i was reading trough above for pi Zero and trying get the unit up and running, but no luck till now, CAN unit is modifed, so 3v3 for mcp and 5v for can tranciever, connections: pin1 3v3 power on vcc for mcp2515 pin2 5v power for cantranciever pin6 gnd pin19/PC0(GPIO Orange PI) MOSI - (MCP2515<->CAN) SI pin21/PC1(GPIO Orange PI) MISO - (MCP2515<->CAN) SO pin23/PC2(GPIO Orange PI) CLK - (MCP2515<->CAN) SCK pin24/PC3(GPIO Orange PI) CS - (…

Hi everyone, I'm trying to connect Tiny LCD to OrangePiOne. I bought this cheap LCD display with touch panel. http://www.aliexpress.com/snapshot/7757492669.html?orderId=75894630877559 --My environment-------------------------------------------------------------------------------------------------- Orange Pi One Armbian Jessie Desktop with legacy kernel DS1302 RTC module(work with WiringOP) 720p DVI Display 2.8" SPI Serial Port 240x320 ILI9341 TFT LCD Display Screen Touch Panel Backlight Module ------------------------------------------------------------------------------------------------------------------------ I connected and tried to configure the L…

I can't make bluetooth work on my OPi0+ Is it a known bug? Am I doing it wrong? thank you

Hello, I'm new to armbian, and I have a few questions. The image on the downloads page uses the legacy kernel (default branch), I used the desktop version of armbian 5.30. But is it possible to upgrade the kernel to the mainline version (4.11)? If so how? and are there any disadvantages? For example will hardware acceleration still be possible using mpv and so on? If it is better to stay on the legacy kernel, then I let everything as is.

Can someone please add support for the onboard microphone to armbian for the Lite2?! It is missing in armbian-config, there is no h6-analog-codec.dtbo in /boot/dtb/allwinner/overlay The microphone is wired up the same way as on the other h6 boards. Thank you very much!

Good day friends! I have Orange Pi PC and I decided to try Armbian. Excellent build! My congratulations to the developers Before, I used the image of 'loboris'. I had a problem with the management of the LED in Armbian. How to make u-boot turn red led to the kernel boot? Edit fex file no avail

hello i have a new sbc board cubie a5e 1GB Ram starting via sdcard 32GB and tried to boot it with armbian cli image. Very early while the boards stuck with: RADXA Cubie A5E 1GB RAM Armbian CLI stuck while uboot via sdcard seems to be an issue with the uboot which hangs very early. With original debian image from radxa the board is b ooting and running. But i intend to use the armbian version with newer debian and kernel. What can i do? Regards Rolf

Hello, I want to buy this display https://www.adafruit.com/products/2354 will seamlessly work with ubuntu on bananapi m1?

Hi, Firstly, congratulations for your amazing work… it's impressive. I have a question regarding the SD image for A10 Lime (Linux 4.x)… Can I enable a raw serial device on /dev/ttyS1 which will use the uart0 of the FEX file? If I understand the FEX documentation, the FEX is no longer used on this kind of image, in favor of DTB files. So, how can I manage to modify the DTB file in order to customize my uart settings ? And, finally, how can I obtain a raw serial device on /dev/ttyS1 which will use it ? Regards, Anthony.

Kinh nghiệm mở shop đồ chơi trẻ em? Đồ chơi trẻ em là luôn luôn cần thiết và là sở thích tất yếu của con trẻ ,giúp con trẻ phát triển các kỹ năng trí tuệ toàn diện, nhất là những sản phẩm mang tính giáo dục. Các bậc phụ huynh ngày càng có nhu cầu cao về những sản phẩm, đồ chơi an toàn cho con,, giúp con phát triển về tinh thần, trí tuệ và thể lực. Chính vì lẽ đó mà cửa hàng đồ chơi đã ra đời và thu hút nhiều khách hàng. Đầu tiên để kinh doanh thì bất kì mặt hàng nào chúng ta cần có nguồn vốn ổn định và đồ chơi trẻ em thì cũng không ngoại lệ. Nếu bạn cảm thấy thiếu vốn thì có thể Vay tin chap tại các ngân hàng, lãi suất cũng rất thấp. Bạn phải dự tr…

There is a patched version that enables noscan=1 , but the one I'm using seems like it hasn't been patched. When there is no AP's around HT40 kicks in ok without noscan=1. With noscan=1 and AP's are around hostapd won't even start in HT20 mode. Any help? root@orangepilite2:~# modinfo 88x2bu|grep version: version: v5.8.7.1_35809.20191129_COEX20191120-7777 srcversion: 43C721C4A870A632EBDE0B5 parm: rtw_chip_version:int root@orangepilite2:~# uname -a && hostapd -v Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux hostapd v2.9 User space daemon for IEEE 802.11 AP management, IEEE 802.…

Hi, is it possible to install RealVNC Server with the title setup ? I use around 7 Devices with RealVNC. I prefer to use this for the 8th too.

Hello everybody, I tried building an in-kernel module for USB Dongle Bus 001 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU] on my OrangePi Plus. Armbian supplied module from aircrack-ng/rtl8812au has become aging and raises exception errors on modprobe -r. It was deactivated : root@orangepiplus:/etc/modprobe.d# vi blacklist-88XXau.conf #blacklist 88XXau I made a fresh install of Armbian minimal image, then switched to : root@orangepiplus:~# uname -a Linux orangepiplus 6.15.4-edge-sunxi #1 SMP Fri Jun 27 10:13:43 UTC 2025 armv7l GNU/Linux root@orangepiplus:/usr/src# cat /proc/version Linux version 6.15.4-edge-sunxi (build@…

Hello, guys. I use debian server version for my board. But I can't use WiFi to connect my router. I have tried wpa_supplicat, but no result. I used many resources for information, such as https://www.blackmoreops.com/2014/09/18/connect-to-wifi-network-from-command-line-in-linux/ https://unix.stackexchange.com/questions/283722/how-to-connect-to-wifi-from-command-line Maybe, I do something wrong. Can you help me please?

Looking for some guidance on how to play mp4/h264 files from the command line.......tried numerous method but not getting any joy (mplayer / mpv). Any definitive guide out there or help appreciated......pulling my hair out with this

I have Orange Pi Plus 2 running Ubuntu Bionic with Armbian Linux 4.19.62-sunxi and I would like to upgrade it to recent Armbian build based on Ubuntu Linux Server and move OS to SSD connected to one of USB ports. I tried to use Armbian_22.08.2_Orangepiplus_jammy_current_5.15.69.img.xz but it does not connect to both HDMI and network. I tried unofficial command line interface images from product page and weekly released unsupported community builds. Behavior of all these builds is the same - no output to HDMI, no network connection. Finaly I found that recent image for Orange Pi Plus / Plus 2 which boots is Armbian_22.08.1_Orangepiplus_jammy_current_5.15.63.img.xz.…

Hello there, I tried to use on OPC3 bionic the ttyS1 for communcation with a serial device and didn't get it to work. ttyS3 works fine. Configuration is done for both. But now I need to communicate with a second and possibly a third serial device. So I hoped for updates. But now I can't find a download of the bionic version and i have to make decision how to go further on. Does it make sense to switch to buster or stretch? Is bionic only temporarily or finally offline? Whats the reason? Any idea when there is a chance to get a stable release. Possibly with 6 Months or surely not within 6 months. Which version is more likely to …

Hello. I have my cubietruck (cubieboard 3) configured to boot from sd card, and other files stored on hdd (sata). Few weeks ago (~15.06.2017) I updated armbian by "apt-get dist-upgrade". It worked well until I switch power off. Now it can't boot from sd card. If I remove it - boot from nand is ok. Whet sd card installed - no activity on display, just blinkin LAN port. If I boot from nand, I cat mount both SD and HDD and explore filesystem. But I can't find any logs, updated since 17.06 (time then I switch it off). My guess problem is new kernel, from 4.11.4 to 4.11.5. Please help me fix this, I can take files and content from SD and HDD, but I don…

Dear friends! Please help me! What am I doing wrong? I have Orange Pi Pc Plus. I am using Armbian. 4 months ago I bought a CSI camera OV5640 from Steven Zhao: https://www.aliexpress.com/item/32869355445.html With expansion board! It's working under Android, but /dev/video0 does not appear in Armbian! ~$ sudo uname -a Linux smart 3.4.113-sun8i #2 SMP PREEMPT Wed May 8 15:09:43 CEST 2019 armv7l armv7l armv7l GNU/Linux :~$ sudo modprobe ov5640 :~$ sudo modprobe vfe_v4l2 :~$ dmesg | grep -i ov56 [ 6555.158751] [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11 [ 6563.092176] [OV5640@lex]CSI_SUBDEV_PWR_ON! [ 6563.16004…

Hi. My platform is Orange Pi Plus. I connected SATA HDD and installed Armbian. Using nand-sata-install I created the following scenario: boot from SD, system on SATA. I also installed lighttpd. Several days everything works fine and than: ...file system on the root filesystem failed … rebooting automatically due to panic= boot argument... After that the PC just reboots constantly and I can do anything. The only solution I found is to repeat the process of boot SD creation. But after that I need to install everything again. All this I already did for several times... What maybe the reason of this error? Can I exclude the SD card and use eMMC instead? Is there anythi…

Hello! I have armbian jessie on cubietruck. I am using it with asterisk software. After 4 or 6 days its hanging. I was change hdd to ssd disk, decrease temperature to 44C, and problem is not solved. Please help me find the way.. i have no battery, and battery on board is not 3v - 1,7v now.

In a brainfart i thought the rpi gpio is compatible with most arm boards. so i took one witch i had laying around and i connected the Raspberry pi DVB-T HAT module (TV uHAT). I checked if the SPI bus pins where compatible and with the help of the "Hardware_Allwinner_overlays guide" i created a overlay for the rpi-tv (used the original from the raspberry pi github). to my surprise (after some struggle) it work. // rpi-tv HAT /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&spi0>; __overlay__ { /* …

Hi all. Firstly, sorry I had posted this query in the wrong forum. I´m trying to add support for a raw SPI comunication through SPI0, as it´s a custom comunication with a little auxiliary board, I think best option is to have a spidev device. My scenario is: Banana pi m2 ultra Armbian 5.4.35-sunxi, server (No gui). I have been modifying .dts and .dtsi files, here are parts of the files that I modified: sun8i-r40.dtsi spi0_pins: spi0-pins { pins = "PC0", "PC1", "PC2"; function = "spi0"; }; spi0: spi@1c05000 { compatible = "allwinner,sun8i-spi"; device_type = "spidev"; reg = …

Hello ladies and gentlemen, I am working on a project for which I use a Nanopi Neo Core with its mini shield. With this mini shield I encountered some problems. The first problem is when I want to know the IP address for an Ethernet connection I got the following answer: pi@nanopiair:~$ sudo ifconfig lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 0 bytes 0 (0.0 RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 …

I am using Orange Pi Zero Plus(http://www.orangepi.org/OrangePiZeroPlus/), but there's no armbian for it. I download armbian for Orange Pi PC2(here) and it works! However, PC2 does not have on-board wifi, so my zero plus cannot find a wlan device. The onboard wifi of zero plus is Realtek RTL8189FTV, and the driver source seems to be this I compile it on my orange pi and add "modprobe mac80211" before "insmod", it is loaded but there is still no wlan0 device So what should I do to enable wifi?

Hello, I can't boot my new OrangePi One v.1.1. I have used various SD cards including Sandisk Ultra 32GB. On the serial console I every time see: U-Boot SPL 2018.05-armbian (Oct 26 2018 - 22:09:12 +0200) DRAM: 512 MiB Trying to boot from MMC1 MMC Device 0 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Power supply is 5V 3A. Ethernet is unplugged and nothing is connected to USB. What I tried: - Flashed on two different computers (MAC and Windows) - used both etcher and dd - checked cards with h2testw for errors (…

Will cryptsetup (missing crypto modules), and USB audio (or the onboard analog audio) work on vanilla kernel?

Hi Dear Friends! I'm having trouble using the onboard analog soundcard from my OrangePi Zero +. I already enabled analog-in in armbian-config, but when I try to run some application that uses the sound card, it has an error. In this example I'm trying to use the direwolf app that serves to decode FSK audio. The error also repeats when I try to use svxlink.

It seems I have to install either of them for my chromecast to play nice. I have no prior experience with neither of them nor do I know which one is better. There are various threads on the internet but would be interested which one the community uses / trusts, cause I am a bit hesitant on adding random repos. My use case: Stream mkv on local with subs or transcode if it can't show subs. Board: Orange Pi Pc OS: Debian Stretch on 4.14.18 Would appreciate any feedback even if it's only a link to your preferred software / guide.

Hello everyone, this is my first post so please be patient. I am using armbian for a long time on my cubietruck, but this time I got a problem with my Orange Pi One. I have build a Embedded Cluster [1] out of a cubietruck, 5 Orange Pi PC and one Orange Pi One system. Since yesterday I have modified my cluster chassis. Maybe but just maybe a short circuit happened on my OPiOne because of some assembly issues I had during it's installation. The problem is that it OPiOne does not boot any more. The red and green LED are still turned off. The two LED'S of the ethernet port are always switched on. Nothing to see on a screen attached to the HDMI port. It a…

Hello to all, I installed Armbian ( legacy kernel ) on my OPI plus 2 H3 but all usb ports not work, only micro usb Otg. I can t use mouse or keyboard someone help me please?

Hi, Thank you very much for all the work. I recently purchased 4GB RAM version of Orange PI RK3399. Was able to install armbian WIP version: 4.4.180-rk3399 I'm trying to capture video via HDMI IN port using gstreamer but I see the following error messages in kernel log, Spoiler Jun 12 03:19:37 localhost kernel: [ 3.956986] tc358749xbg 1-000f: probing... Jun 12 03:19:37 localhost kernel: [ 3.957006] tc358749xbg 1-000f: GPIO lookup for consumer int Jun 12 03:19:37 localhost kernel: [ 3.957016] tc358749xbg 1-000f: using device tree for GPIO lookup Jun 12 03:19:37 localhost kernel: [ 3.957101] tc…

HI! I have debian wheezy with kernel 3.4.106. When I ran nand-sata-install script, it executed successfully. But after that system doesn't boot from nand. Just black screen. Any help please?

I have done a fresh installation of the Debian image (http://mirror.igorpecovnik.com/Armbian_4.5_Cubietruck_Debian_jessie_4.2.3.zip), but since that the linux does not report any information on power and the battery. There is no information in /sys/class/power_supply. As I am not an linux expert, any useful informationhighly welcome

Good evening, I'm using a NanoPi Neo Air for streaming audio via bluetooth to a I2S sink. It's working in general but the audio data breaks away every second. It's always a on/off. I'm pretty sure it's connected to the speed between H3 - AP6212a but I'm not able to get it to work propably. I set the UART ttyS3 speed to 1500000 bit/s: My Fexedit looks like that: [bt_para] │ │bt_used = 1 │ │bt_uart_id = 3 │ │bt_uart_baud = 1500000 │ …

Hey all, Sorry for the noob question, I posted this in another topic but it hasn't seen any action so I thought I would make a post. I have an Orange Pi PC, using the RetroOrangePi build which is based on Armbian. I'm having overscan issues on my 720p TV. I checked the options on the PC, there's no way to fix it there. They figured it out in this topic here (where I initially asked this question): The solution is to add code to u-boot in order to solve the overscan, or edit boot.cmd. My question is, will using u-boot be the best solution, or is it better to edit boot.cmd? Do I simply create a boot.cmd in something like note…

Hi, as I need to use an OS allowing me to have Cozy and Gladys (both node.js) on my router (using them it as server) I tried to use armbian for the first time. I sucessfully installed armbian on a SD Card and boot it. My BPi-R1 is not connected to a display or other periherals (keyboard / mouse). Because I do not have those materials I sold them. It is just connected with RJ45 and has a HDD connected on the SATA port. I then connected my modem RJ45 connector to my BPi-R1 on the WAN port. I connected my computer on the first port (near the WAN one). I saw my laptop do not get an IP certainly due to the fact that LAN port seems to be manually activated. …

I've got a NanoPi Neo Core 2 and a NanoPi Neo Air. It bothered me that the USB OTG did not function in host mode. Turns out, the included Armbian .dtb's don't have the parts necessary to define the regulator which pushes power back to a client device when the board needs to run in OTG host mode. You can see the regulator on page 8 of the schematic http://wiki.friendlyarm.com/wiki/images/6/6b/NanoPi_NEO_Core2-V1.0_1707.pdf I found an upstream patch at https://patchwork.kernel.org/patch/9921097/ which defined the missing parts for a Neo Plus 2. I put the relevant parts into an overlay dts file (attached) that can be loaded wit…

Hi,I have a problem with the ssh wifi connection with the nanopi neo air it has every faith that I connect it is too slowI have disabled the NetworkManager with the following commandsSystemctl stop NetworkManager.serviceSystemctl disable NetworkManager.serviceAnd configured my network connection with the / etc / network / interfaces fileAnd also i have disabled iwconfigIwconfig wlan0 power offalways remains the problem of SSH slowthenks for your help

Hi, I'm trying to set up an Orange Pi Zero with Armbian, so that I can use it as a Network Card (i.e. when I plug it into a computer it's automatically recognized as a Network Card). It seems there isn't enough documentation about this issue. Can anybody help me, please? Thanks in advance. Kind Regards.

Hi, I had set up my orange pi pc a long time ago and kinda forgot about it. I am looking at upgrading from debian 8 to debian 9 and I am not sure how it works with armbian? Do I just change the sources.list from jessie to stretch? or do I need to do something special? sources.list deb http://httpredir.debian.org/debian jessie main contrib non-free deb-src http://httpredir.debian.org/debian jessie main contrib non-free deb http://httpredir.debian.org/debian/ jessie-updates main contrib non-free deb-src http://httpredir.debian.org/debian/ jessie-updates main contrib non-free # security packages come always from main repository deb http://s…

Hello everybody, I have a orange pi zero h2 and when I connect the gpio on some pcb, sometime the pcb inject file inside the linux and create dpkg error. is it possible to enable something to protect the system. thx you

Boot from SD without any problems, then install to NAND (no error)... In NAND boot it comes in the log... (transcription from a photo) [ OK ] Started LSB: Set preliminary keymap. Starting Remount Root and Kernel File Systems... [FAILED] Failed to start Remount Root and Kernel File Systems See 'systemctl status systemd-remount-fs.service' for details. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems (Pre). Mounting /boot. [ OK ] Started Load/Save Random Seed [ OK ] Mounted /boot. The 'Failed' message is the only error in the log. Problem: Can ssh locally ('ssh localhost') but can't from outside (it shows nothing). ping is responding. If I …

Since U-Boot v2025.04 works very well on Orange Pi Zero v3 and has a shorter boot process time, if there was a possibility to switch to U-Boot v2504 for Orange Pi Zero V1, I would be grateful, as would probably other users of this SBC Regards

PSA - trunk 130 is not a bootable image. trunk 100 works fine.

I have two NanoPi R1s, both with Armbian Buster. I want to use both as wireless access points, however the wifi seems to be problematic. It always works at first, but not anymore after updating, changing the config and rebooting. My hostapd config is the following: # # armbian hostapd configuration example # # nl80211 mode # ssid=[myssid, contains some numbers] interface=wlan0 hw_mode=g channel=6 [11 on the other one] #bridge=br0 driver=nl80211 logger_syslog=0 logger_syslog_level=0 wmm_enabled=1 wpa=2 preamble=1 wpa_psk=[random thing armbian-config generated] wpa_passphrase=[secret] wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP wpa_strict_rekey=1 wpa_dis…

Hello, I know there is documentation about it, but I think I've tried everything and my orange pi is still not displaying on my hdmi screen. The green LED is active, and the red one is blinking. I've written a Raspian image to the sd card, corresponding with the board. I have read about bin2fex but I can't have access to my sd card data on my Windows, to execute bin2fex. Thank you for your help !

Hi, Perhaps it is documented elsewhere but I could not find a direct solution after googling few minutes. My u-boot partition was stuck at the same version on the nightly. I needed to fix the reboot issue. I've tried few things like apt upgrade or direct dpkg -i... Anyway, this is what I did on a EMMC installation (/dev/mmcblk2) after I've built and download my own version of the package: dpkg -i ./linux-u-boot-dev-orangepi3_5.86_arm64.deb cd /usr/lib/linux-u-boot-dev-orangepi3_5.86_arm64 cat sunxi-spl.bin u-boot.itb > u-boot-sunxi-with-spl.bin dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2 bs=1024 seek=8 reboot I'm my case I had to u…

Hi all, Recently i have purchased an orange pi lite2 board(H6) for codec audio streaming.I would like to establish the interface between Orange pi Lite 2 (H6) and AC108(codec board) for audio recording.I have downloaded Android source code and start making changes in Fex file, but couldn't get any luck. I am confusing in which I2S driver need to be used for H6 to communicate with codec (AC108). I am totally new to orange pi boards. so, please clarify following doubts... 1).which i2s driver needs to be map with codec(AC108) driver? 2).what all changes are required in Fex file? 3).How to set sysclk, clkdiv, fmt ? Please clarif…

Thanks for the hard work on Armbian. I finally got the EmulationStation GUI to run under OpenGL ES @ ~88fps on OrangePI PC. The trick was mostly building SDL2 from source and not installing it with apt-get per the instructions. Really want to avoid anything "mesa". IIRC, I configured SDL2 with a similar command before making: ./configure --host=arm-linux-gnueabihf --disable-video-opengl Then building EmulationStation from source using: cmake -DGLSystem=OpenGL\ ES . make make install FWIW I did symlink some shared objects into /usr/lib/ (like libMali.so) Next is sorting out libretro stuff.