Allwinner sunxi

It was set to mount cifs in fstab, but seem not automatically mount. Since this is not supported?

Nach dem upgrade kann OMV nicht installiert werden Hallo an Alle Seit gestern geht das Installieren von Openmediavault nicht und zwar auf Armbian 4.8.4 und 4.9.5 Wenn ich Update friert das ganze System ein. Hello everyone Since yesterday, the installation of Openmediavault does not start Armbian 4.8.4 and 4.9.5 If I update freezes the whole System

WiringNP does not work on NanopiDuo2, both in 18.04 and Ubuntu 20.04 Error piBoardRev: Unable to determine board revision from /proc/cpuinfo -> Is not NanoPi based board. -> You may want to check: -> http://www.lemaker.org/ open /sys/class/su Armbian /proc/cpuinfo content: processor : 0 model name : ARMv7 Processor rev 5 (v7l) BogoMIPS : 136.80 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc07 CPU revision : 5 processor : 1 model name : ARMv7 Processor rev 5 (v7l) Bo…

I have an Orange Pi PC that I bought from eBay a while ago and it works absolutely fine, has done for a month or so now. I have just bought 5 more from Xunlong's Aliexpress store, they arrived very quickly, however they don't appear to boot... Power rails are fine, 24MHz clock is fine, reset line is fine, fel mode registers with my PC fine, however no UART output, no apparent attempt to boot from the SD card. If boot it with the SD card in, I get absolutely nothing, if I boot it without the SD card, it gets into FEL mode and I can talk to it with sunxi-fel nick@nick-desktop:~/sunxi-tools$ sudo ./sunxi-fel ver AWUSBFEX soc=00001680(H3) 00000001 ver=0001 44 0…

please enable green led Banana-pi M1 Armbian 5.75

Just started with Orangepi and ARMbian ... ARMbian is a very nice OS. Especially since there's a RAW image for Orange pi! Thanks! I've got two DS18B20 working perfectly with my Orange pi pc! But now I've troubles with the BMP085 /BMP180. With my old Raspberry pi it was pretty easy, but how can I get the BMP180 running? I 've read there are modules for ARMbian, but I've read as well I've got to compile my own module. Does anybody know where can I find the files /module to load or compile?

Help please! I have a bp2 which was bought almost a year ago, and use Armbian_5.14_Bananapi_Debian_jessie_3.4.112.raw as the image for couple of months. Today, I'm try to upgrade to the Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw image, but the pi can't boot at all. What I do to prepare the sdcard with the following procedure: 1. remote the old partitation, and create a new fat32 partitation 2. dd bs=1M if=Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw of=/dev/sdc; and sync 3. mark the written partitation as bootable with fdisk ps: I'm using fish shell, and the syntax for the dd command is valid So, what's wrong with my steps? How can I troubleshoot? …

How do I copy sdcard image to nand . I tried to use the ./nand-sata-install script and it returns the following message " There are no targets. Please check your drives. "

I'm powering my NanoPi Neo V1.4 1801 through the USB type A port beside the Ethernet RJ45. I'm using Armbian 23.11.1 bookworm with kernel Linux nanopineo 6.1.63-current-sunxi. Now I want to enable the Micro-USB port (usually used for powering) to act as an USB host so that I can plugin an USB-stick. I found very few instructions for e.g. Orange Pi. There the device tree needs to be changed for usb@1c19000 and usb0-vbus. Also in armbianEnv.txt the line param_usb0_mode=0 should be added. But none of the instructions work for my NanoPi Neo. In the schematics, a SY6280 is connected via GPIOL2/USB0-DRVVBUS to the H3 cpu. …

Hi all, I build Armbian for my NanoPi Air with both Linux 3.4 and Linux 4.X, and config usb to be an USB Ethernet Gadget but it does not work with Linux 4.X. There is nothing showing when "dmesg | grep gadget" on Linux 4.x But in Linux 3.4 I got following messages: root@nanopiair:/# dmesg | grep gadget [ 2.559263] g_ether gadget: using random self ethernet address [ 2.565929] g_ether gadget: using random host ethernet address [ 2.582905] gadget_is_softwinner_otg is not -int [ 2.582923] gadget_is_softwinner_otg is not -int [ 2.583012] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 2.590546] g_ether gadget: g_ether ready [ 13.…

If I put a USB stick in I can see it in Nautilus(yes I installed nautilus) but when I click on the name of the USB , I get.. " Unable to access “USBNAME" Not authorized to perform operation (polkit authority not available and caller is not uid 0)" Everything else is working. I have Samba, SSH, x11vnc, NAS, HEVC x265 Video, all working happily.I can live without USB but I thought it would be important to give the Armbian developers feedback. I have looked for an answer and I do not see any one else having this problem. Once again I just love this Armbian / OPi.pc combination. Seasalt

Hello guys, I am trying to blinking POWER_LED on my orange pi lite using google firebase but I couldn't find any resources on internet.... Here is my armbian info; http://sprunge.us/RhTM I want to develop ioT application using orange pi zero coz it has internal ethernet and wifi connection options and it is cheap. What I want to learn is: - I want to develop my ioT application using python - which version OS I should load - proper GPIO or related library for controlling GPIOs and rs-485 and i2c communications Thanks.

Hi, it ist well known, that a SD-card can be destroyed when you power-off a Raspberry-Pi without a shutdown. Does the same issue exist with an Orange-Pi (One) ? I want to use an Orange-Pi One headless and without SSH/TTY, only some sensors and LEDs are attached. Tnx L

I just booted up a fresh install of Armbian 5.24 (Armbian_5.24.161128_Orangepizero_Ubuntu_xenial_3.4.113) on my Orange Pi Zero and I can't seem to get IPv6 working. It worked fine on Armbian 5.22. It's like the dhclient command isn't able to set the address or the address is silently getting dropped or something. Setting ipv6 address via dhclient fails for both eth0 and wlan0. I ran dhclient by hand to see if a problem would be listed in the output but there's nothing: root@orangepizero:/var/lib/NetworkManager# /sbin/dhclient -d -v -6 -N -sf /usr/lib/NetworkManager/nm-dhcp-helper -pf /var/run/dhclient6-wlan0.pid -lf /var/lib/NetworkManager/dhclient6-1cfb9f48-cd01-41…

I have opi2 + (debian server) marian@orangepiplus:~/FFmpeg$ cat /etc/*release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepiplus BOARD_NAME="Orange Pi+" VERSION=5.24 LINUXFAMILY=sun8i BRANCH=dev ARCH=arm IMAGE_TYPE=stable PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" I have gone through a lot of instructions, but without success. I always end up on: marian@orangepiplus:~$ sudo ffmpeg -i vlc.ts -pix_fmt nv12 -qp 20 -c:v cedrus264 -f null /dev/null ... Stream #0:6[0x140f]…

at OPI PC with kernel Linux orangepipc 3.4.112-sun8i #30 SMP PREEMPT Sat Apr 30 19:49:10 CEST 2016 armv7l GNU/Linux before the last kernel update we use rt2800 wifi dongle. dmesg | grep usb - shows this output: [ 0.963044] usbhid: USB HID core driver [ 169.650117] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 169.948904] usbcore: registered new interface driver rt2870 after the last kernel update with apt-get update in 2016-06-08 which include these updates: Start-Date: 2016-06-08 10:31:45 Commandline: apt-get upgrade Upgrade: linux-jessie-root-orangepih3:armhf (5.10, 5.11), libavdevice53:armhf (0.8.17-2+rpi1, 0.8.17-2+rpi1+deb7u1), f…

Hello guys, i have a orange pi prime. I'm download to https://dl.armbian.com/orangepiprime/Ubuntu_xenial_dev_desktop_nightly.7z this image and i flash to 32 gb sandisk card. System is not opened, i see "starting kernel" message and some controls after it's rebooting continuos. I dont start it. I'm waiting for your helps. King regards

First, I am generally not a Linux person, so pardon any silly questions here. I am working on an OrangePi Plus 2E with (recent) Armbian. It has been working fine with the Jessie Desktop for several weeks now. I generally am running it 'headless', so I'm not sure exactly when, but sometime between last Saturday and yesterday I seem to have lost the desktop (and autologin, ...). I see a number of messages on the console at boot, including 'Stopped User Manager for user ID 1000' and then removing 'slice' for this user. The system is operating fine, just not the UI. So, how do I get autologin and desktop back (other than a new install)? What might have caused …

I have two Olimex Lime 2 eMMC boards, both set up the same way – same HDDs, same batteries, same power supplies, etc. Both run: - Armbian 5.31 (although one was updated to it, and the other was freshly installed with that version) - Debian 9 “stretch“ (same issue when they were both on Debian 8 “wheezy” though) - Linux kernel 4.8.14-sunxi Yet, one shows the CPU temperature, and the other doesn’t. A (the fresh-installed one): cat /sys/class/thermal/thermal_zone0/temp 41800 B (the one updated to 5.31 from a previous 5.x version): cat /sys/class/thermal/thermal_zone0/temp cat: /sys/class/thermal/thermal_zone0/temp: Inv…

Hi I'm an happy user of : Armbian_5.14_Orangepipc_Debian_jessie_3.4.112_desktop.7z. I don't know if it is bad luck or some obscure legal reason but 2 of my USB dongles needed to add firmware files from other distributions before they worked perfectly: They are : TerraTec Electronic GmbH Cinergy T RC MKII using dvb_usb_af9015 missing dvb-usb-af9015.fw 15913 bytes from 30/03/2015 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter using rt73usb module missing rt73.bin 2048 bytes from 24/11/2014 I hope those files can be added to ease the life of newbies.

This is a simple one, but the most annoying. The only Linux distribution I can not get to work in the Armbian on the Banana Pro. Sandisk 32Gb Class 10 MicroSD card. A USB power supply that does supply sufficient power and current. I write the image to the MicroSD card, insert it into the Banana Pro's card holder, power it up, the red LED lights up and ................. that's where it stops. No heartbeat on the green LED. The one thing I notice is that the image I download has only got one partition on it and that's the ext4 partition. It does not have the small FAT formatted partition and I think this is where it all goes wrong. …

Hi Guys, After a long time after the release Linux kernel 4.x I want use the I2S on Lime2 (Armbian Stretch kernel 4.14.14), but I2S interface did not work. I was add activation of overlays i2s0 and i2s1 into/boot/armbianEnv.txt root@lime2:~# cat /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=dcf7af80-8026-4e99-870f-f0d35f926063 rootfstype=ext4 overlays=i2s0 i2s1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u After reboot I can't see I2S interfaces... root@lime2:~# aplay -l aplay: device_list:270: no soundcards found... root@lime2:~# lsmod | grep snd snd_soc_core 118…

Hi, I'm using ARMBIAN Ubuntu 14.04.4 LTS 4.4.3-sunxi on a Cubietruck board with a battery connected. How do I setup the system to safely suspend, shutdown or hibernate when the battery power is low? Thank you very much.

Good day, We use NanoPi Neo Core in voice information systems. We found a problem with the implementation of Dynamic Audio Power Management for Portable Devices in H3. Our program plays voice files using the standard call of the operating system - "aplay". Before starting the reproduction of each file the voltage is discharged and restored at the output of the DAC. This leads to a loud click on the output of the audio system. Setting pmdown_time = -1 does not save the situation. Can you help in solving this problem? P.S. This problem appeared in version 4 of the kernel.

I upgraded some day ago to a new release and I experiencing increase cpu heat. My OPI Zero is running 24/7 and most of the time (99%) it has nothing to do. So its in idle. When I run >> ARMBIAN Ubuntu 16.04.1 LTS 3.4.113 have cpu idle temp around 38-39c (room temperature 22c) After the upgrade to >> ARMBIAN 5.25 stable Ubuntu 16.04.1 LTS 3.4.113 increased the idle temperature to 49-50c (room temperature 22c) Am I alone with this problem..? I dont see any increase in processor activities, but I did not analysed which processes are running and different after the upgrade. Been using, armbianmonitor -m to keep an eye on the temperature. To avoid OPI Z…

I had successfully installed openCV for armbian using instructions from this page: http://www.pyimagesearch.com/2015/10/26/how-to-install-opencv-3-on-raspbian-jessie/ I also highly recommend Adrians's openCV tutorials. happy openCV-ing Mladen

Hi ALL, i've problem booting Armbian from SD. Tried to do workaround: 1. boot linaro from SD 2. put tar Armbian Jessie archive to /armbian folder 3. bind /dev, /sys, /proc 4. chroot in armbian folder 5. changed nand1 and nand2 to the nanda and nandb in script 6. started nand-sata-install.sh 7. it installed system on nand. Process finished smoothly. unchrooted. Powered CT off. After power it on have a green LED lighting. CT not booting. Gents, please any ideas? What i missed in procedure.

Hello to all! I'm using Armbian on my BananaPi board. I've the following version: ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.15-sunxi BOARD=bananapi BOARD_NAME="Banana Pi" VERSION=5.35 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage I need to follow these instructions to wire a radio on the board: https://www.mysensors.org/build/orange But I cannot find the script.bin file. Why? I can remember the file was here on old releases. Any help or suggestion? Thanks, Simon

Hi, I am a newbie to Armbian so I apologize if this is a stupid question. I am running Armbian legacy. I think I have successfully programmed a GPIO shutdown button for the Orange Pi Zero by cobbling together information from this and the Orange Pi forum. My script goes like this, in file hw_shutdown.py: #!/usr/bin/env python import os import sys import subprocess if not os.getegid() == 0: sys.exit('Script must be run as root') from time import sleep from subprocess import * from pyA20.gpio import gpio from pyA20.gpio import connector from pyA20.gpio import port button_shutdown = port.PA2 #PIN 20 """Init gpio module""" gpio.in…

Hello, when I am using unionfs on RPi, in /etc/fstab I change this proc /proc proc defaults 0 0 /dev/mmcblk0p1 /boot vfat defaults 0 2 /dev/mmcblk0p2 / ext4 defaults,noatime 0 1 to this proc /proc proc defaults 0 0 /dev/mmcblk0p1 /boot vfat ro 0 2 /dev/mmcblk0p2 / ext4 ro,noatime 0 1 mount_unionfs /home fuse defaults 0 0 mount_unionfs /etc fuse defaults 0 0 mount_unionfs /var fuse defaults …

Hello, recently got a pinebook. I have a strong Linux-on-PC-user background (running ArchLinux on my desktop & older netbook, and debian oldstable on my home server laptop), but not really a developer background and no experience with single board computers at all! Ubuntu Mate is happily chugging along right now, but video playback (h264 packed in .mkv) is abysmal to non-existent. I have tried these releases; the stable 0.6.2 first: AFAICS, it uses a frambuffer driver (fbturbo) under Xorg. video playback was more than choppy, and the UX drops to zero because the video window can't be resized and sticks to the screen, …

I'm a newbie. Got the NanoPi R1 that sports a UART but no Video Output. Now when I want to read the output of the serial console I need a 3-wire cable and a converter, that much I know. But what is the baud rate? Where is this configured on the armbian NanoPiR1 image (on my raspberry Pi I just checked and found the file /boot/cmdline.txt with that settings, in my case it's 115200) Why is the baud rate nowhere documented? On the download page https://www.armbian.com/nanopi-r1/ it is stated that "serial console is enabled on UART1, which is exposed on chasis" , but no hint about which speed to use. There neither is any info about the baud rate on…

How do I get a desktop running on this (legacy)? It only outputs a shell on the video out Additionally, is the hw video decoder enabled? Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113

Dear All, I am beginner to linux and Opi Zero. I have written some programs on OPI Zero with WiringOP-Zero library. I got all of them working. Right now I am stuck on graphic library. I need to make a graphic library based program. I am going to draw some vertex data and update them according to received data on serial port. I don't have any idea where to start. I used C# and XNA in the past. I know something about game programming. ( Please note, I did not make a game, I made a program which draws some information visually on screen with XNA framework) Could you please suggest me, Where should I start? I have two board. I…

Hi, i tried to use wlan0. I added an "ap6210" in /etc/modules. I added in /etc/network/interfaces auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ap-scan 1 wpa-scan-ssid 1 wpa-ssid mywlanssid wpa-psk andthepassword During loading i see two lines about ap6210 INFO Loading Module 6210 (or similarly) Fatal Module Ap6210 not found I wonder, how can I add the needed files? I am using this Image: http://www.igorpecovnik.com/2014/09/07/banana-pi-debian-sd-image/ Debian wheezy 4.1.2 In the discription is a hint, that everything should available. Many thanks in advanced for an hint. Im not very involved in linux. Regards, Ti…

Hi I am having issues getting an external RTC (DS1307) to work properly on the OrangePi + 2E I am using the current version of ARMBIAN 5.6.5 (Stretch) The hardware side of things works perfectly. If I use i2cdetect -y 0, I see the I2C bus transaction on an oscilloscope and I also see the device as shown 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- --…

Hi, I'm using an hdd at my cubietruck and moved the root-fs to hdd. Now I'm wondering, whether it would be better, to change the commit settings in /etc/fstab to a lower value than 600? I assume, the 600 was meant for data on a flash storage in order to reduce the writes on it!? But in order to keep "things in sync", shouldn't I better reduce it? Or delete the whole commit option? What do you mean? Thanks and best regards, Jochen

Hi all, I run a BPi with Armbian 4.2 - kernel 4.2.2. A WD Red 3TB is connected via sata. I have tested hdd performance which seems to be very slow (for my opinion). Auto Mode Using Minimum Record Size 512 KB Using Maximum Record Size 8192 KB File size set to 2048000 KB Using maximum file size of 2048000 kilobytes. Command line used: iozone -a -y 512k -q 1024K -s 2000m -g 2000m -i 0 -i1 Output is in Kbytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 Kbytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. …

Hello together sorry for this long description but I want to provide all information I could save. I'm running armbian since 2(?) years and had never a serious problem with it. Today the system was not reachable anymore (services, ssh, ping) so I rebooted the server. Rebooting worked but all my data is on an external encrypted harddisk which I couldn't open anymore: root@MyCubietruck:~# cryptsetup luksOpen /dev/sda1 MyEncryptedHarddisk Enter passphrase for /dev/sda1: device-mapper: reload ioctl on failed: No such file or directory Failed to setup dm-crypt key mapping for device /dev/sda1. Check that kernel supports aes-xts-plain64 ciphe…

Hi, I'm trying use USB Audio card it's works fine in this cammand aplay -D hw:2,0 test.wav hardware Orange pi one version Armbian 5.11 root@orangepione:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 use portaudio library and get this error root@orangepione:~/portaudio/bin# ./paex_sine PortAudio Test: output sine wave. SR…

I want to install debian or armbian or what ever it is for Orange Pi One to be a server. I downloaded Jessie server from here: http://www.armbian.com/orange-pi-one/and extracted the 7z file. I do now know what to do with the raw-files I extracted. At first I tried to install install basic Debian from here: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=342&extra=page%3D1 but I didn't undestand the instructions after mounting SD Card FAT partition. I'm not even sure am I suppose to mount it to Orange Pi or the PC I used to write the image to th SD. So I went looking for another way and found the first mentioned which was seemed to be made …

Hello, greetings from Bulgaria and thanks for the OS. We use Orange Pi Lite and something may be is problem. Full boot time is around 1 min and 15 sec, how can we degree this time because it's so slow? When we was with 5.23 distro it was around 45 sec with same SD card and power supply.

Verify kernel 4.6 with dev on test construction Armbian where the CPU is not recognized correctly. root@orangepipc:~# lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0 Off-line CPU(s) list: 1-3 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: ARMv7 Processor rev 5 (v7l) [ 0.001455] CPU: Testing write buffer coherency: ok [ 0.001769] /cpus/cpu@0 missing clock-frequency property [ 0.001784] /cpus/cpu@1 missing clock-frequency property [ 0.001794] /cpus/cpu@2 missing clock-frequency property [ 0.001805] /cpus/cpu@3 missing clock-frequenc…

Greetings to all, Preamble: Thanks to all that have worked to make the Armbian project what it is today. It is greatly appreciated! I have done numerous hours of reading and searching (due diligence). I know I could run a benchmarks and all but that means even more delay reaching the objective. Some brief guidance from those who have gone before would save a lot of time and would be greatly appreciated. Looking at the datasheets wasn't real helpful in guesstimating optimum performance configuration - especially since there are so many other factors that have an impact. Background: My objective is to achieve a reliable, long lif…

I have a NanoPi Neo Air (Allwinner H3 SoC) with onboard wifi and a serial interface. Unfortunately during some late hour hacking I managed to accidentally connect 5V onto its TX pin, I think effectively screwing up its UART0. I can no longer connect to it via a USB to TTL Serial cable. Looking at the NeoPi Nano Air's pinout diagram, it seems to have more UART devices (UART1 and UART2 even) so I wonder whether there's a way to set up armbian to communicate via these during boot? Another idea I had was to try to bypass the UART completely and to hook up the board via the wifi. Now, without having any access to a serial console, I need to …

Hi, I tried to enable the i2c in u-boot by using the config flags shown in the Readme. But I had no success. What do I miss?

I had a NanoPi NEO2 working well with ARMBIAN 5.34.171121. After apt-get upgrade, ARMBIAN has been changed to ARMBIAN 5.37.171208 with below firmware update: Get:1 http://beta.armbian.com xenial/main arm64 linux-dtb-next-sunxi64 arm64 5.37.171208 [25.0 kB] Get:2 http://beta.armbian.com xenial/main arm64 linux-image-next-sunxi64 arm64 5.37.171208 [14.7 MB] Get:3 http://beta.armbian.com xenial/main arm64 linux-u-boot-nanopineo2-next arm64 5.37.171208 [222 kB] Get:4 http://beta.armbian.com xenial/main arm64 linux-xenial-root-next-nanopineo2 arm64 5.37.171208 [318 kB] Then the Ethernet port is no longer working. Kernel message shows MDIO register f…

Hey there So I was planning on using the OPZero on a robot that I had already made, which took use of SPIdev, and it was doing calls to the spidev driver in C. Now I noticed that the OPZero has 2 SPI channels, one for the NOR flash (Which isnt populated) on the back and another that goes to the GPIO headers on the device. Now I ran my script, and turns out that /dev/spidev0.0 is actually writing SPI commands to the rear SPI channel. This is apparenly SPI0 according to the schematics. Now following the schematics again, I want to access SPI1, which currently does not exist as a spidev file. I tried "modprobe spidev" to bring up the extra interface, but sadl…

Hello so i got Orange Pi PC 2 today and installed armbian from here : https://www.armbian.com/orange-pi-pc2/ i can SSH to it. but i dont know how to get AV out to work :/ can u help me ? im a total Beginner i just need to get Tv out to work and start learning. I know that armbian for H5 is in the early development state.

Hi forum members, when I try to install the kernel headers via: "sudo apt-get install kernel-headers-$(uname -r)" I gote these errors: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package kernel-headers-4.19.62-sunxi E: Couldn't find any package by glob 'kernel-headers-4.19.62-sunxi' E: Couldn't find any package by regex 'kernel-headers-4.19.62-sunxi' In the /etc/apt/sources.list the lines with the deb-src links are comments. I've tried to uncomment these but got the same errors. So please can somwone point me right kernel-headers Armbian is using ? Many T…

Hi everyone, I'm facing a problem with logrotate on my OrangePi Zero with Armbian Focal mainline. Basically I have a process that is always running with a `tee` command that outputs the stdout to a log file in the /var/log/ directory. My logrotate configuration file looks like the following: /var/log/smartbit/gocpp.log { rotate 10 daily compress missingok notifempty copytruncate dateext } It's all working correctly except the copytruncate part: logs are daily rotated and gzipped but the gocpp.log is not truncated to 0 bytes, so it gets bigger and bigger. I noticed that in this new Armbian version logrotate is not triggered…

Dear All Have anybody tried and connected the following screen to Orange PI under armbian? If so, could I please ask any instructions? http://www.aliexpress.com/item/Orange-Pi-7-inch-LVDS-LCD-Module-7-Touch-Screen-F-Raspberry-Pi-Car-GPS/32315435767.html

I have certain problem when using ssh on my Orange Pi zero. When I am connected through on-board wifi module the ssh panel have a lot of lag when I am writting commands. However I am not experiencing the same problem when I am connecting through ethernet. I can't understand if that's a case of bad connection as I have the same behaviour even if I put my pi next to my router. I know that the on-board wifi module is not the best but it seems that its unusable. Anyone has any relative problem? Is there any solution or its just hardware based and I need an external wifi dongle?

Hi,I want to know how to disable serial console /dev/ttyS0 on NanoPi NEO2 with allwinner H5. My Environment: Board:NanoPi NEO2 uname -a: Linux nanopineo2 4.14.4-sunxi64 #11 SMP Thu Dec 7 11:55:12 CET 2017 aarch64 aarch64 aarch64 GNU/Linux dmesg | grep tty: [ 0.000156] console [tty0] enabled [ 1.655315] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 24, base_baud = 1500000) is a U6_16550A [ 1.655383] console [ttyS0] enabled [ 1.678058] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 25, base_baud = 1500000) is a U6_16550A [ 1.700706] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 26, base_baud = 1500000) is a U6_16550A [ …

Hello, sorry but my english is not best. I tried to search forum for these problems, but I do not found the answers First problem is that serial console do not work for me, just random symbols, I already tried 3 USB to RS converters with 3.3 V logic, hercules_3-2-8 and putty as SW, with multiple setting, mostly 115200, 8 data bits, no handshake, no parity. Second problem the HDMI do not show useful data either, at least for me there was nothing I can understand as problem. I have 2 orange Pi lite available, so it is probably not a board problem, I tried 2 SD cards and multiple images (desktop legacy kernel 3.4.y and mainline kernel 4.14.y …

Hi, I have two OrangePi Lite running side by side. After working fine for about 8 months both started to experience same issue with wireless: The board works randomly for few hours or few days and then looses wireless connection. When this happens reboot does not help as then issue occurs immediately after the boot. Unplugging and replugging power source resolves that for a while and then happens again I suspect it may not be related to a hardware issue or wireless hotspot, as I have at least 3 other clients that continue to work fine. Searching for it on the internet brought this issue with Raspberry Pi: https://github.com/raspbe…

Hi, I'm Olivier, french engineer, and i have bought an orangepi plus card in april. I use linux (x86) since 1994 Sorry for my bad english ... I was happy to find Armbian because linux images provided by xunlong have many security problems (example / and all system directory aren't owned by root but by orangepi user). Thank for your work on Armbian. My Orangepi + has been installed with a 5.10 armbian image (Armbian_5.10_Orangepiplus_Debian_jessie_3.4.112) and run perfectly. I wanted upgrade to 5.20 and since the card doesn't boot anymore. I can boot with the native android on NAND memory but I can't boot on SDcard. When I boot on sdcard, only gr…

I am running my Cubietruck with Debian and want to connect my JeeLink USB Adapter for home automation with OpenHAB. It is recognized by the system (lsusb): Bus 003 Device 002: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC The driver module seems missing, as no /dev/ttyUSB0 is created. dmesg | grep usb states: [ 1.525290] usb 3-1: new full-speed USB device number 2 using sw-ohci Is the driver included in the image? If not, how can I install it? Thanks for your help! Stepman

Hello. I have installed debian based armbian with mainline kernel to my orange pi zero. And it seems like there is no i2c adapter present. As far I know it should work in mainline. Does anyone have a clue?

ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.19.38-sunxi Orange Pi Zero Board Please refer armbianmonitor.log for armbianmonitor -U command output details I have configured My Orange Pi Zero onboard wlan chip (xradio_wlan driver) to work on both Ap mode and Client modes simultaneously. When both Ap and Client interfaces are up and working, and when the connected wifi channel of the Client interface changes, kernel hang occurs. Error message [20148.872296] rcu: INFO: rcu_sched self-detected stall on CPU [20148.877893] rcu: 1-....: (4945709 ticks this GP) idle=8aa/1/0x40000002 softirq=9640/9640 fqs=2447771 [20148.887182] rcu: (…

I need 3 USB ports (webcam, wifi 5G, 3d printer). On Zero Plus 2 H3/H5 micro usb port is occupied by usb charger, because none of my devices can play as power source. So, only 2 usb ports left, not enougth. Is it possible to make micro usb useable somehow? For example, via custom usb cable etc. I need micro-usb male / micro usb male cable (OPI <-> 3d printer board) + supply power somehow. PS. i don't like to add external usb hub.

Very grateful to armbian to provide such a good image！ Armbian has released many images that have been packaged with OMV。 I am follow this link for a long time：http://kaiser-edv.de/tmp/NumpU8/ I'm happy to see more and more mirrors available。 I used one of the images named OMV_3_0_72_Orangepiplus2e_3.4.113.7z and it works good，Special thanks to tkaiser！ There is another model（Orangepiplus2） that is better suited for NAS Because it has a sata interface https://www.armbian.com/orange-pi-plus-2/ Can Armbian provide OMV images of the above motherboards? At last, sorry for my poor English.

Hello. I'm trying to communicate with i2c ( i've connected ADS1115 on it if this maters ), but even without anything connected on it - it shows 0x30 on it, and I am not sure how to make it works. Please help ! 😐

Hi, I wanna try the armbian for banana pi M2 but when i flash the image in the microSd card with Rufus (i'm on windows 10) the pi does not boot correctly, i.e restarting every 10 seconds. Afterwards the card is not easy to reformat, not accessible on windows. In Rufus I do (i tried with 2 different cards): - choose the .raw file - then the combobox is set to DD image - finally i click on start So is there something I totally miss? Thx

Hello every one, I have used crosstool-ng on my Jessie server (x86), and downloaded the linaro toolchain for my Ubuntu (x64 / 16.04) laptop, but ran into a wall both times: the cross-compilers won't (and now that I think about it, can't) link to the host libraries. Do I simply get all the sources for the libraries I want/need, and adjust their configure parameters to point to dedicated directory, and then build my target? Is there an easy way to manage the versions / dependencies to match Jessie (the version on my target OPi)? I am trying to compile Duktape with libreadline, if that matters. Thanks, Steve

Hi. For some days I was working to compile a customized live distro based on Armbian and live-boot for my BananaPi M2+ board. Finally, it is ready to use. It boots from the builtin emmc flash and is completely readonly. It uses overlayfs together with squashfs. It also uses zram as swap to enhance memory capacity. A nice effect is that the sd/flash image becomes only 400mb, since it is squashed.. I would share the image and the details of making it, if somebody is interested, send me a message...

Hello Ones again I`m would like to connect 1 LED to GPIO and make it blink . I try to find tutorial on Wen but for OPI Win it`s not work (duo to lack tutorial for this models) Could You help me wrote simple code to make LED start blinking? With program included in Armbian to steering GPIO for my OPI Thanks in advance.

Hi All, I'm new here, well been lurking a while reading heaps, just not posting before now. My Orange Pi's arrived a few days ago so I have been playing, I have Ubuntu_xenial_3.4.112 image on both types and am able to connect to home wifi and do apt-get update/upgrade so all good here. One thing I wanted to do is use batman-adv, but the kernel module seems to have been disabled on the armbian images: @orangepipcplus:~# cat /boot/config-3.4.112-sun8i |grep BATMAN # CONFIG_BATMAN_ADV is not set It took me a while to figure out how to confirm this was the case but another post pointed me to the /boot/config-3.4.112-sun8i file. So this is where I need so…

Hi there, I need help in finding the lates Debian Buster image for my R1. Please can you point me to the latest version ? Many Thanks Wollik

I just installed Armbian 5.30 Desktop to my Orange PI Plus 2E I want to use for video playback, but built in MPV player. MKV videos quality is good, but the player has very poor functionality. And it plays Xvid Encoded AVI files totally mess way with lots of artifacts, sometimes with colored stripes instead of video stream. I also tried SMPlayer and VLC, but they play some MKV files with green artifacts and AVIs are totally mess. I tried different settings for VLC but have not reached success with the settings. So what video player is universal and good for Armbian ro what settings should I set to get good video quality?

I'm using Mainline 4.9.5 for cubieboard2 (Armbian_5.24_Cubieboard2_Debian_jessie_next_4.9.5.7z). I boot without LAN or WIFI dongle using TTL port to get console interface. When I try to log how root ( root / 1234 ) the log system throw me always in error: cubieboard2 login: root Login incorrect cubieboard2 login: When I confirm root username the system don't ask me to insert the default password (1234) but after a while send me a 'Login incorrect'. LOG from sudo screen /dev/ttyUSB0 115200: U-Boot SPL 2017.01-armbian (Jan 20 2017 - 22:22:43) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.01-armbian (Jan 20 20…

I originally installed Armbian_5.38_Orangepizeroplus_Ubuntu_xenial_next_4.14.14 I got NTP with PPS up and running on UART2 with PPS on PA3 I have a working backup image of this. I then used armbian-config to boot from USB disk and I installed a LAMP stack and battled to get a DB up and running. My mistake was upgrading the kernel before making a backup. My version is now ARMBIAN 5.38 stable Ubuntu 16.04.4 LTS 4.14.48-sunxi64 NTP and PPS no longer work. Is there a way to downgrade the kernel without having to go back to the backup and battle with the DB config again? I'm a Linux newb so please make allowances for my ignorance. I have searched for sev…

Hi all, some days ago I successfully built the image mentioned above (Build environment is Ubuntu 14.04/64 bit). The only remarkable issue was the ever-repeating "firstrun" script, which was easily solved with the method mentioned here: http://forum.armbian.com/index.php/topic/1100-post-install-scripts-on-every-reboot/#entry8509 (may be ALL of the scripts should be changed this way?) But today, after checking out the actual "master", I see a lot of failed copy and sed commands until the debootstrap-ng script finally fails at Mali-libdri2. The 1st occurrence of an error was during installation of "ramlog". I've inserted a breakpoint and looked into the imag…

INFOS: Armbian Bionic mainline kernel 4.19.20 System: OrangePi Pc Monitor, full HD (1920*1080), over HDMI. SOLUTION, ROTATE SCREEN: My rotation Settings that i try: 1. xrandr (not permanently, only for this session) 2. echo n > /sys/class/graphics/fbcon/rotate_all n=0,1,2,3 (permanently solution) See: http://linux-sunxi.org/Display <-Point:Rotation PROBLEM: Screen rotation problem: On every boot the rotation is correctly applied BUT: Turn Monitor off an then on again, the rotation is NOT applied. PROBLEM SINCE : Quarterly update cycle, until november 2018 everything works fine and i did not have thi…

This started happening since accepting the kernel when I used apt to upgrade the BananaPi Pro sbc I've got. armbianmonitor report: https://paste.armbian.com/izuboducul @teknoid are you aware of this?

I had it and lost it: u-boot with I2C. I did not write down how I did it (was heavy) Tried to build yourself again: does not work. u-boot-mizi.bin does not want to boot. For 2 days I try to find the solution. Google has already blocked me Can somebody help? I need i2c directly, after power on, to read FRAM and set relays. Programming in Linux is enjoyable but system administration is horrible. Thanks

Hello, first of all many thanks to all the community that keeps this project alive. I recently bought a NanoPi NEO2 board and of course decided to drop the OS provided by Friendlyarm and give a try to Armbian's Ubuntu build for this board. Everything seems to work just fine, however I'm unable to get a reading on the CPU Frequency. I tried multiple tools and commands but somehow all end up with something like "cpuinfo_cur_freq: No such file or directory. For instance, here is the output of armbianmonitor: armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armb…

Hi all, I was struggling to have a stable Wifi connection on my new Orange Pi Primes, and believe I found a solution, so I thought it's nice to share it Symptoms: Wifi would connect right after reboot, but would disappear if Orange Pi Prime was idle for about 30min. The only way to reactivate would be to either pull the cable out (as there are no buttons yet), or to login via ethernet, perform ifconfig down && if config up. I didn't liked either of the options, so I decided to investigate. My log was full of: [89201.577208] RTL8723BS: nolinked power save enter [89201.967063] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is n…

Friends I have a keyboard Rii i8 + I put the adapter that comes with the keyboard I put to locate by the bluetooth of the armbian it finds but at the time of pairing in happens nothing, only blinks green in Bluetooth and nothing else. I've tried another adapter, but it does not even appear as installed. This keyboard I use it with Openelec and works perfectly. Does anyone have any tips on what I can do for it to work on Armbian? Thanks.

hi all, My Orange Pi PC here: uname -a Linux orangepipc 3.4.112-sun8i #30 SMP PREEMPT Sat Apr 30 19:49:10 CEST 2016 armv7l GNU/Linux and dmeg like this [ 1.017014] asoc: sndcodec <-> sunxi-codec mapping ok [ 1.017964] [DAUDIO]sunxi-daudio cannot find any using configuration for controllers, return directly! [ 1.018158] [I2S]snddaudio cannot find any using configuration for controllers, return directly! [ 1.018174] [DAUDIO0] driver not init,just return. [ 1.021480] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok and I check status of ALSA lib # systemctl status alsa-state.service â— alsa-state.service - Manage Sound Card State (restor…

Hello. I have a small problem: I can't change the language on my OPi Zero. I have successfully done that with OPi Lite 2 and OPi 3, but for some reason on the Zero when I go to change it, the module fails to load and just quits back to the same "menu page". (essentially does nothing). The only thing I can think of, is that both of the other boards have 1Gb RAM and this only has 512Mb and thus it runs out of memory? That doesn't sound too plausible though - a list of keyboard languages shouldn't take tens or hundreds of megs of RAM. As far as I know, each board is running the same version of Armbian, so that shouldn't be a problem.

Hi. I would like to install Armbian on Cubieboard2 with eMMC as internal storage and have faced some problems. The first challenge was to make eMMC accessible, it was solved using .fex from cubieboard sdk for this revision (also tried cubieboard2dual.fex, but without any effect). The second problem was behavior of nand-sata-install included in desktop image - it overwrite wrong root partition (external SD instead of eMMC), but it was also solved using latest version of nand-sata-install. But after installation, system isn't booting from eMMC. Since root filesystem is successfully copied to eMMC, I think there is problem with bootloader. Is there an…

I downloaded Ubuntu server from here https://www.armbian.com/orange-pi-plus-2e/ and then burned it using Etcher to my SD card. I never loaded/installed any OS on my Orange Pi Plus2E before. Without SD card it permanently shows only Allwinner H3 logo on screen, so it seems no OS installed there. Red led is permanently on (not blinking) and nothing elase is happen. After I insert the SD card with the burned image I immediately get green LED on (not blinking), red LED is off. The monitor screen is permanently black and nothing else happens. When I connected USB/UART converter I saw the following in the logs: U-Boot SPL 2017.05-armbian (Jun 13 …

Hi, we are trying to make our Orange PI zero with custom shield working with an MCP2518FD on board with SN65HVD23 tranceiver. We started from the normal kernel already built, but according to this thread we found that it must be activated at compile time. So we downloaded the repo and built the Armbian image with this CAN configuration: CONFIG_CAN=y CONFIG_CAN_RAW=y CONFIG_CAN_BCM=y CONFIG_CAN_GW=y CONFIG_CAN_J1939=y # # CAN Device Drivers # CONFIG_CAN_VCAN=y CONFIG_CAN_VXCAN=y CONFIG_CAN_SLCAN=y CONFIG_CAN_DEV=y CONFIG_CAN_CALC_BITTIMING=y CONFIG_CAN_FLEXCAN=y CONFIG_CAN_GRCAN=y CONFIG_CAN_SUN4I=y CONFIG_CAN_TI_HECC=y CONFIG_CAN_C_CAN=y CO…

Been trying to compile the handy sysdig util in armbian. Installed it with: apt-get install -t jessie-backports sysdig sysdig-dkms After the normal install that worked, but when running gave this error: error opening device /dev/sysdig0. Make sure you have root credentials and that the sysdig-probe module is loaded. I tried: /usr/lib/dkms/dkms_autoinstaller start One of the compilation errors I manage to correct commenting the include of asm-offsets.h in /var/lib/dkms/sysdig/0.5.1/build/main.c I also managed to solve the complaints about the lack of fixdep with: make fixdep make bin2c However now when trying to compile it with /us…

Hi, I am facing an i2c problem on orange pi 3. The i2c0 is enabled in armbian-config. The i2cdetect output is correct, as I know my two slave boards connecting to gpio pin3 (SDA) and pin5(SCL) have the addresses 0x20 and 0x23. pi@orangepi3:~$ sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 -- -- 23 -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -…

Hello, I am trying to make simple AP on my orange pi zero. sudo nmcli c add type wifi ifname '*' con-name Hotspot autoconnect no ssid Hotspotssid sudo nmcli connection modify Hotspot 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared sudo nmcli connection modify Hotspot wifi-sec.key-mgmt wpa-psk sudo nmcli connection modify Hotspot wifi-sec.psk "lepassword" sudo nmcli connection up Hotspot But after "sudo nmcli connection up Hotspot" I am getting "Error: Connection activation failed.". Any idea please? P.S. Connection to internal home wifi network works ok.

Have anybody tried to setup Amazon Alexa on the OpiPC?

Hello, Recently I found that audio stopped working on my Banana. Last time (3 months ago) I was using shairport to stream audio over LAN and all was working just fine. Now I see that somehow information about audio card was removed: root@bananapi:~# alsamixer cannot open mixer: No such file or directory root@bananapi:~# cat /etc/asound.conf cat: /etc/asound.conf: No such file or directory I already try apt-get update && apt-get upgrade && apt-get dist-upgrade. My system information: root@bananapi:~# uname -a Linux bananapi 4.9.12-sunxi #4 SMP Thu Feb 23 19:46:51 CET 2017 armv7l GNU/Linux root@bananapi:~# lsmod Module …

FYI & FWIW: Howto find your NanoPi NEO2 Your NanoPi NEO2 is connected to your LAN, but how to find it? What is the IP address? Here are my methods: Via bonjour (Ubuntu to Ubuntu): ssh nanopineo2.local. Example: $ ssh nanopineo2.local. sander@nanopineo2.local.'s password: _ _ ____ _ _ _ ____ | \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___ |___ \ | \| |/ _` | '_ \ / _ \| |_) | | | \| |/ _ \/ _ \ __) | | |\ | (_| | | | | (_) | __/| | | |\ | __/ (_) | / __/ |_| \_|\__,_|_| |_|\___/|_| |_| |_| \_|\___|\___/ |_____| …

Hi, during the spring I used h3disp - 720p50 -c 1 (on 5.24 with sunxi-tools 1.4.2) to change the resolution for my desktop but today when I did a clean install (armbian 5.30 Jessie Default) I get Unsupported board/kernel combination: Orange Pi Zero running 3.4.113-sun8i. Exiting Is there still a way to change the resolution (720x576 is too low for the gui app I need to run)? Thanks in advance! Nicke

Greetings, I'm not good with linux so excuse any stupidity i might say. I have been using Xenial for years now and just decided to update. In the past i was using the sunxi module to access gpio's For ex: echo 1 > /sys/class/gpio_sw/PA7/data Now in Bionic i just noticed gpio's are not accessed in the same way. According to this user, we can either use sysFS (which seems deprecated) or libgpiod. The problem is that i can't make it work. libgpiod: root@orangepi:~# gpioset gpiochip0 29=1 gpioset: error setting the GPIO line values: Unknown error 517 sysFS: root@orangepi:~# echo "29" >/sys/class/gpio/export -bash: echo…

What module should I load to get SPI working on 4.x kernel image? My usual suspect spi_bcm2708 is not available. I once used it on Banana Pi M2 from other manufacturer (SinoVOIP?) with Raspbian, now on Banana Pro I'm stuck with not working SPI.

hi every body! in last two days, i have been trying to make my orange pi zero board to hotspot device. i follow instruction at armbian documentation and it's work fine. but i want more than a simple bridge network. in order to use nginx to show my website to connected devices, i need to set ip to connected devices. i used both of isc-dhcp-server and dnsmesq, but it failed every time a device want to connect to board. dnsmasq config: interface=lo,wlan0 no-dhcp-interface=lo dhcp-range=192.168.8.20,192.168.8.254,255.255.255.0,12h interface config auto lo iface lo inet loopback iface eth0 inet dhcp auto wlan0 iface wlan0 inet static hostapd /etc…

Hi All, I'm using Armbian_5.10_Micro_Debian_jessie_3.4.112 on a custom A20 board with NAND based off the Olimex A20 Micro. I don't see /dev/nand on it. $ zgrep NAND /proc/config.gz CONFIG_SUNXI_NAND_PARTITION=y CONFIG_SUNXI_NAND=y # CONFIG_SUNXI_NAND_COMPAT_DEV is not set # CONFIG_SUNXI_NAND_TEST is not set I even tried to Livesuite an Android NAND image, but it also failed. I'm pasting the logs below. What does it generally mean to have a missing /dev/nand? Thanks. $ sudo ./LiveSuit.sh Starting x86-64/LiveSuit. library file path: /home/asrolabe/Downloads/sunxi-livesuite/x86-64/plgvector.dll library file path: /home/asrolabe/Downloads/sunxi-livesuite…

Hello, I'm new to this forum and Armbian. I've got an Orange Pi Zero 2+ H5 running the Armbian_5.34.171121_Orangepizeroplus2-h5_Ubuntu_xenial_next_4.13.14 image. It's connected to a device via UART1 using pin 1 for 3.3V, 6 for GND, and 8/10 for TX/RX. I've been trying unsuccessfully to use pyserial in a Python script to read data from the ttyS* devices, but I can't seem to cat anything from them either. I've tried moving the device to a RaspberryPi Zero W and I'm able to read the output from ttyS0 successfully. I did have to run raspi-config to enable the UART on the RPi, but I'm not aware of an equivalent on the OPi. I believe I added the uart1 overlay to my…

The old 0.14.0 version doesn't work well with subtitles, ending up with subtitles drawing on top of each others, when the text is moving fast. Is there any build I could download and install? Or some other workaround? Edit: Kodi draws the subtitles correctly, but it has pretty awful screen tearing. Using black bloxes instead of just some outline on the subtitles does work, but it's not an acceptable fix to me. So, it would be great it was possible to use whatever kodi uses to draw the subtitles, but then use mpv to draw the video.

Hi Igor, could you please look into the character set problem mentioned in the comments? Jessie kernel 3.4: Line-drawing graphics for programs like aptitude or mc don't work. The screen displays garbled characters instead, which renders all programms with a graphic interface unusable :-(. After install I noticed that dpkg-reconfigure locales did not work as expected. LANGUAGE stays en_US and LC_MESSAGES stays posix. I configured them manually # update-locale LANGUAGE=de_DE.UTF-8 LC_MESSAGES=de_DE.UTF-8 but german umlauts (äöü) still don*t work although the system now seems to be configured correctly for de_DE.UTF-8. I don't care too much about the u…

Hello friends; I have board which Orange Pi Win Plus running Armbian. My problem is, boards 7, 8, 10 and 16 physical pins are not working. When I tried to I/O with this pins, console says: Segmentation Error. Is it possible to fix it or is it normal? Thank You.

Hi Can anyone help with the installation of Open Media Vault Erasmus on Armbian Jessie for the Orange Pi Zero. I have been following instructions given all the following link but I am unable to download the required packages: http://www.fredmerc.com/2016/11/installing-openmediavault-erasmus-to-debian-8-jessie/ Any help or information would be appreciated. Thanks