Allwinner sunxi

Hello, I'm trying to interface an I2C device to Orange Pi Zero with armbian. By running i2cdetect I obtain the following result: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- I've tried to load …

Hi...Is support for using Mali GPU of Orangepi PC2 enabled for armbian? I'm trying to install the mesa-dri utilities and getting stuck in the libc-bin segmentation fault? Is it because of lack of support or something else? Also I'm getting issues of protobuf while compiling Opencv for Orangepi PC2. If anybody can help!!

Sir, I put ubuntu trusty image on Sd card in A20-micro-4gb board. I connected serial cable to uart0 connector which has 4 pins tx,rx,gnd,3.3v. But the log shown is strange. Minicom settings are 115200, 8N1. Please confirm that debug interface is on uart0 or any other pins.

Hi everyone, I am having issues with video output on my A20-micro when using legacy kernel. I get the proper output from uboot, but when it starts to load the kernel, I get some garbage on the screen, then nothing. I had a look through the forums to no avail. My boot logs are uploaded to http://sprunge.us/dGhS From what I see, the default kernel command line seems to be correct for my purpose. The system is up and running as I can login through serial and SSH. I tried setting the resolution with a10disp but I got the following response: "Cannot change HDMI mode because HDMI is not enabled." Anyone has a clue on what I am missing ? Than…

I'm using wiringPi installed from here, it works fine for the most part but when I try loading spi it throws the following error: modprobe: FATAL: Module spi-sun7i not found in directory /lib/modules/3.4.113-sun8i gpio: Unable to load spi-sun7i FYI: I'm using Armbian 5.31

I'm running some stress test on the NanoPi neo2 512mb, CPU heating reached 75-76 degrees, and it's stable, the problem that I faced is that the computer changed it's IP suddenly (after 55 minutes of test running), I guess it's because of a network card reset. Did anyone face the following issue? Is it related to the stress test? Or it's another networking problem? The test I'm running is with the "stress" tool, running long time stress on 4 CPUs. In addition, does anyone have any insights regarding this device? good or bad?

Hello, how to enable analog tvout? I have OpiPC board with legacy jessie desktop armbian image. I added module tv in /etc/modules. I change script.bin with: [disp_init] disp_init_enable = 1 disp_mode = 1 screen0_output_type = 3 screen0_output_mode = 10 screen1_output_type = 2 screen1_output_mode = 11 fb0_format = 0 fb0_width = 0 fb0_height = 0 fb1_format = 0 fb1_width = 0 fb1_height = 0 [tv_para] tv_used = 1 tv_dac_used = 1 tv_dac_src0 = 0 But there is no signal at all... I checked tvout with loboris ubuntu image (added "tv" to /etc/modules and fixed script.bin) and my tvout worked well. I noticed that when ubuntu image is loading tvout already gives to…

i run a cubietruck on armbian with 4.6.2 kernel. it starts with the software on mmcblk0p1 (with kernel 4.6.2 and the /lib dir on the sd) but uses as root a partition of the ssd. when i upgrade now, i see that the upgrade process produces a new initrd.img-4.6.3 and removes the old 4.6.2. (diagnosis: the system runs, but the keyboard/mouse connected to the usb is not functional - desktop over net works!) i assume that there is something wrong with the boot.cmd - but i do not see exactly how to fix it. the upgrade process uses the ssd .../lib directory and removes 4.6.2 there. if i would mount the /boot directory with the running system (in fstab) - would this hel…

Hello, now my system is running well on my Cubietruck: (ARMBIAN Ubuntu 16.04.1 LTS 4.8.1-sunxi) Booting from SDCard rootfs on SSD (installed via nand-sata-install script) Whereas a image backup of SDCard is easy, how to backup my rootfs on SSD for system fallback Szenario: Is there any good script to backup rootfs of SSD with shrinking function to get small backup files? simply TAR of "/" of SSD? Use of webmin backup functionality (howto store this backup on network drive outside my Cubietruck)? Best Regards, Martin

Hello, I'm using Armbian Xenial with ethernet on my local network. SSH and PostgreSQL seem to disconnect a lot. This is really frustrating with sshfs when I try to work with files on the Orange Pi Zero as a file server.. I tried setting a keepalive every second and that doesn't help either. I don't see anything in the logs that hints to anything. I have not attempted to use wifi. I did just notice the timezone was wrong, so I'll see tomorrow if that has something to do with it.

Hi, I'm facing a problem with my Orange Pi Zero with the latest Armbian version. I noticed that when I provide an internet connection type that is not valid (wrong psk, ethernet but no cable plugged in, etc.) and I reboot the system, it hangs just before asking the username and password. Sometimes it takes up to 10 minutes before keeping going. These are the last boot logs that I see: [ 11.209226] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 11.219428] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped. [ 11.244988] systemd[1]: Started Nameserver information m…

Good evening! Thats my first post, I have for a year a Orangepi 3 LTS that I used for my kid, he looks that never switch off the unit by software and use the switch all the time, so suddenly the unit dont boot anymore, the SD card partition table was corrupt, so I mounted a new OS in another SD but does not boot, the green light is not coming anymore. So I connected a TTL to USB Serial device for debugging and it shows the following information: U-Boot SPL 2021,10-orangepi (Sep 06 2022 - 18:22:23 +0800) PMU: AXP806 DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: NOTICE NOTICE NOTICE: INFOS NOTICE NOTICE: INFO: INFO: INFO? BL31: BL31: BL3…

I am a newbie here and newbie in Orange Pi One. Previously I have used Raspberry Pi in my daily projects. I burn Armbian 5.05 to my class 10 SD Card and after install the SD Card to the board. My Orange Pi One is booting properly but after automatic restart, my board doesn't continue to boot but the red LED is ON. I have tried to wait for 10 minutes but nothing work. This is my first booting https://www.youtube.com/watch?v=_RA68P_WZJY .

Hello dear friends, please help can not solve a problem, the entire forum has clambered! as I can not turn on your WiFi Orange Pi Pc + ....

I'm using an Olimex LIME2 board with an A20 processor (actually it's a Olimex A20-SOM, but that shouldn't matter) and trying to use PWM. I have an older image (jessie with Kernel 3.4) where the PWM hardware can be accessed through /sys/class/pwm-sunxi/pwm*/{duty, duty_percent, period, pin, polarity, pulse, run}. Now I'm building a newer image (xenial with Vanilla kernel). It has /sys/class/pwm, but the directory is empty. Any ideas? The fex file is the same for both boards; the relevant section is: [pwm0_para] pwm_used = 1 pwm_period = 10000 pwm_duty_percent = 50 [pwm1_para] pwm_used = 1 pwm_period = 10000 pwm_duty_percent = 50

Guys, please help. I installed one orange pi plus 2e and orange pi one in following way: first server image (legacy kernel) then kernel upgrade to mainline. Everything works just fine, except I do not receive kernel updates. If I understood well, kernel should be upgraded via apt dist-upgrade.. But nothing. On both this machines I've got same situation: Welcome to ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 4.11.5-sun8i igor@orangepione:~$ uname -a Linux orangepione 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l armv7l armv7l GNU/Linux in my apt sources I have: igor@orangepione:~$ grep -h ^deb /etc/apt/sources.…

Hello, I have an an orange Pi plus 2+. I had installed armbian ubuntu 18.04.2 on it. I used it only on wired network, and I experienced that the downloading speed is perfect, but the uploading speed is very slow. So at the network synchronous, the upload is same fast as download. On the same wiring and with another device I have not noticed this phenomenon before. Do you know what can be the reason of this? Speedtest:

Hey everyone. I have an MK802 II stick, which has the A10 s.o.c, so i use the Olinuxino Lime a10 image on it. Everything works pretty much fine, except one little thing. This machine has worked fine with non-standard resolutions, like 1440x900, or 1280x1024. Now, when i turn it on, the U-boot screen appears correctly, it even shows that it set the resolution to 1440x900, and after that, the monitor says "signal out of range". Of course, it works well with a 1080p monitor, but i wanted to use this one too. Thanks!

Finally Orange PI Family gets the 4.x kernel support.But there is no Vanilla Kernel on Orange PI PC.Please add the support on Orange PI PC.Thx!

Kinh nghiệm mở shop đồ chơi trẻ em? Đồ chơi trẻ em là luôn luôn cần thiết và là sở thích tất yếu của con trẻ ,giúp con trẻ phát triển các kỹ năng trí tuệ toàn diện, nhất là những sản phẩm mang tính giáo dục. Các bậc phụ huynh ngày càng có nhu cầu cao về những sản phẩm, đồ chơi an toàn cho con,, giúp con phát triển về tinh thần, trí tuệ và thể lực. Chính vì lẽ đó mà cửa hàng đồ chơi đã ra đời và thu hút nhiều khách hàng. Đầu tiên để kinh doanh thì bất kì mặt hàng nào chúng ta cần có nguồn vốn ổn định và đồ chơi trẻ em thì cũng không ngoại lệ. Nếu bạn cảm thấy thiếu vốn thì có thể Vay tin chap tại các ngân hàng, lãi suất cũng rất thấp. Bạn phải dự tr…

After few hours wlan0 lost connection for unknown reason (reason=0) and then it looks like some kernel module crash. Is it driver problem? Any suggestion will be very appreciated! Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: wlan0: CTRL-EVENT-DISCONNECTED bssid=40:b0:76:58:52:d8 reason=0 locally_generated=1 Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: p2p-dev-wlan0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: p2p-dev-wlan0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=CZ Dec 31 19:22:05 tns_3np NetworkManager[812]: <info> [1577816525.4151] device (wlan0): supplicant interface …

Hello, I have an orange pi plus 2 device. but Armbian 5.69 (5.75 or latest version) above Orangepiplus Ubuntu xenial default can be the url for desktop version. Can you please give me the working url? (By the way, I couldn't find a section for orange pi plus 2 in the forum. )

Hello, I am a beginner on NanoPi. I had a NanoPi neo 512M, and I am searching for a campatible image for it. unfortunately, I didn't find my device in the list but I found NanoPi Neo 2 instead. I believe that its image is not compatible with my device so, can anyone give some hands to have a compatible image? thanks in advance

Today I noticed that last Sunday a community version of Armbian was released with Orange Pi 4A support. I tried to flash it in different ways just in case, but it just wouldn't boot. I used BalenaEtcher, Rufus and Armbian Imager and neither of them worked. Im new in this stuff, so I wanted to know if someone could tell me if it is something I'm doing wrong.

Hi guys, I installed last armbian on Banana Pi M2+, and execute nand-sata-install.sh to boot armbian from emmc, it works fine. I want system boot from emmc, and storage some data to sd card, so I prepare one sd card with ntfs partition, insert to Banana Pi M2+, and boot. It cannot boot, and message are: U-Boot SPL 2016.05-armbian (Jun 23 2016 - 09:59:04) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 23 2016 - 09:59:04 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial…

Greetings, all! I've got a LeMaker A20 BananaPro, on which I'm using the Armbian mainline distribution (for a more complete description of my setup, please see below). I'm using a serial console to the board; I'm not connecting anything to HDMI for display. I'm running the distribution off of a brand new 8Gig SanDisk Extreme Pro. I would like to use alsa (at least in part) in the audio stack. I'm experiencing the following: When I have no audio playing through the audio out jack, I get a loud (powerline, probably) hum on my speakers. When I start audio playback (a wav through aplay, or an mp3 through mpd, etc.) the hum disappears, and the so…

Hello We are using NanoPi M1 board for robot application.So I am trying to install Ubuntu 16.04 LTS. I want installation procedure for Ubutu. In nanoPi M1 manual they mentioned only for Windows OS. If anyone knows procedure please help me.

I've been struggling for a while to get raspberry pi HAT type LCD to working. I've been working with loboris images before until recently that I've heard that armbian has cooked a new image for orangepi with newer kernel. In the description of images it is clearly indicated that the image works with small screen lcds which it seems to be true because there is no error when I want to load a notro module and it successfully loads. I've put lcd configurations in /etc/modules but I was not successful. this is the parameters I use in /etc/modules fbtft_device name=flexfb gpios=dc:22,reset:27 speed=48000000 flexfb width=320 height=240 buswidth=8 init=-1,0xCB,0x39,0x2C,0x00…

Hello everybody, I am running 3.4.113 on my Orange Pi Zero like a charme. Now I was trying to install aircrack-ng-1.2-rc4. I am getting the following error: So I checked on the missing libnl: So for me it looks ok, does anybody have any idea how to fix the error? Thanks for some help

Installed tightvncserver and sudo apt-get install xfonts-base. When I try to connect and see the "foto". How can I fix this?

Hello, to all OrangePI PC enthusiasts. Well I'm in the community of those who definitely underestimated the Orange of the PI, but let me share my burden :-) for the fun of it. It started with the camera- gc2035 and vfe_v4l2 modules. Had to try a couple of images until I got it by luck I guess - after that I found out that every image I use is not capable of having a FTDI device connected to "ANY" USB Port (OK, you got me, I didn't try the microUSB and I won't). After that I tried no matter what I wanted to connect to USB it was not even recognized. Now I'm back in changing/swapping around Images until I found one that let me plug anything I …

I've tried to install GitLab onto Banana PI running Armbian (Ubuntu 16.04 server). I've followed the instructions for Raspberry PI (on https://docs.gitlab.com/omnibus/manual_install.html) and generic https://about.gitlab.com/installation/#ubuntu Unfortunately this fails: $curl -s https://packages.gitlab.com/install/repositories/gitlab/raspberry-pi2/script.deb.sh | sudo bash ... $ sudo EXTERNAL_URL="http://myurl.com" apt-get install gitlab ... Verifying we have all required libraries... Could not find gem 'devise-two-factor (~> 2.0.0)' in any of the gem sources listed in your Gemfile or available on this machine. Did anybody tried the same? Is t…

Hello Guys. เว็บพนันบอลต่างประเทศ เว็บแทงบอลต่างประเทศ HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

/sys/class/leds is not populated when running jammy with kernel 5.16.11

Starting kernel ... <6>Booting Linux on physical CPU 0 <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.4.113-sun7i (root@vultr.guest) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1) ) #1 SMP PREEMPT Tue Jan 24 12:18:02 UTC 2017 CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun7i <6>Memory Reserved: <6> SYS : 0x43000000 - 0x4300ffff ( 64 kB) <6> LCD : 0x44000000 - 0x44ffffff ( 16 MB) Memory policy: ECC disabled, Data cache writealloc <6&gt…

Hello, No bluetooth device in my Armbian... Banana Pi M2+ ARMBIAN 5.65 stable Ubuntu 18.04.1 LTS 4.14.84-sunxi dpkg-query -Wf '${Version}\n' bluez 5.48-0ubuntu3.1 No Bluetooth device(hci0): rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Which refers to the error: systemctl status ap6212-bluetooth.service ● ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Tue 2019-01-08 09:18:38 UTC; 1min 2s ago Docs: man:systemd-sysv-ge…

Hi, I am using Linux nanopiair 3.4.113-sun8i distribution on my Nano Pi Neo Air and trying to get the g_ether works. After using modprobe g_ether and set up the network/interfaces auto usb0 iface usb0 inet static address 192.168.0.2 netmask 255.255.255.0 then edit /etc/modprobe.d/g_ether.conf: options g_ether host_addr= 06:7b:95:4c:59:d7 After reboot it shows: [ 6.868451] usb0: MAC 06:7b:95:4c:59:d7 [ 6.868475] usb0: HOST MAC 5e:5b:65:8f:94:85 [ 11.484526] systemd[1]: Found device /sys/subsystem/net/devices/usb0. [ 16.249726] ADDRCONF(NETDEV_UP): usb0: link is…

Hello, with the update to the new kernel (4.6.3-sunxi) I get some problems on my banana pro. First, while the system starts I get sometimes a kernel panic. In the most cases the kernel will boot on the second or third try. But the second one will be contantly and can't be avoided by a system reboot. The network interfaces don't be worked. The will be initialized during the system start process, get there IPv4 addresses from the router per DHCP and ifconfig shown them with the state "up". Everything looks ok. But if I try to connect another system, the connection will be failed. Any ping, as exsample to the router (default gateway), fails. The ping t…

Hello i found it on both my Opi PC+ and Opi Plus 2E , Both ARMBIAN 5.59.180918 nightly Debian GNU/Linux 9 (stretch) 4.14.70-sunxi. As i get some stability issues with Jeedom i'm playing with frequencies and governors and found that strange thing : root@orangepipcplus:~# cat /etc/default/cpufrequtils && cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true MIN_SPEED=408000 MAX_SPEED=1296000 GOVERNOR=ondemand 240000 480000 648000 816000 912000 960000 1008000 1104000 1200000 1296000 root@orangepipcplus:~# it seems there…

Hi there, I have been trying Armbian Buster for the first time. On the first look everything works fine and quick. But I cannot get proper sound from the soundcard. Instead there is only random noise. Interestingly the speaker-test works fine in stereo. $ uname -a Linux teres-a64 5.4.28-sunxi64 #20.02.7 SMP Sat Mar 28 17:25:10 CET 2020 aarch64 GNU/Linux $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun50ia64audio [sun50i-a64-audio], device 0: 1c22c00.dai-sun8i sun8i-0 [1c22c00.dai-sun8i sun8i-0] Subdevices: 1/1 Subdevice #0: subdevice #0 $ speaker-test -twav -c2 -Dhw:0 speaker-test 1.1.8 Playback device is hw:0 S…

Hello, I am not able to get the keyboard working. I have tried the downloads and compiling my own images. Bulleye is the only thing I can get to compile. There are error massages if I try to compile anything other than Bulleye.

Armbian 6.6.16-sunxi64 (bookworm) on NanoPi NEO2 NanoHatOLED fails: - GPIO devices are missing; 2024-03-29 23:04:55 root@M-DNS:~# uname -a Linux M-DNS 6.6.16-current-sunxi64 #2 SMP Fri Feb 23 08:25:28 UTC 2024 aarch64 GNU/Linux Seems regression of earlier issue that had been solved: Would appreciate as GPIO will restored in kernel.

hi guys, im trying to compile media_build but it says the kernel has no i2c mux support how could i easy compile a new kernel with i2_mux enabled on the orange pi?

Hello! I'm using Wheezy under kernel 3.4.x on Lime2 with 7" LCD and i added fbcon=rotate:1 in boot.cmd and the console booted in portrait but LXDE is still in landscape. I also added FBDEV_ROTATE_CCW=90 but with no results. I can rotate the screen from the /usr/share/X11/xorg.conf.d/XX-fbturbo.conf file but every time i touch the screen the LXDE crashes. Any suggestions please how to rotate the screen in LXDE? Thank you!

Im tring to access the GPIO using Python3 on a bananapi M1 Linux m5 4.19.38-sunxi #5.85 SMP Wed May 8 14:20:48 CEST 2019 armv7l GNU/Linux I manage to get access to gpio in shell, c, and in python2, but not in python3 with the following software: https://github.com/BPI-SINOVOIP/BPI-WiringPi https://github.com/BPI-SINOVOIP/BPI-WiringPi2-Python The error in python3 is the following (in pyhon2 work) : Traceback (most recent call last): File "/root/src/BPI-WiringPi2-Python/wiringpi2.py", line 18, in swig_import_helper fp, pathname, description = imp.find_module('_wiringpi2', [dirname(__file__)]) File "/usr/lib/python3.5/…

I'm trying to make a master image to install to some NanoPI Neo boards. I have everything running fine from micro SD card. I used armbian-config to flash from SD to the eMMC and it boot and works. Now I'm looking for a way to flash the eMMC from command line in an automatic fashion, after looking for other threads in the forum I found about command nand-sata-install but it has a GUI and no --help parameter, so I guess it is not the exact program I have to use. I tested using dd command to copy the disk, but since there is this u-boot thing I think it is not just a standard disk copy because it failed (maybe my problem). My final idea is to have a master SD …

Hi, 2 weeks ago I upgraded my Cubietruck to newest Armbian version: root@cubietruck04:/var/log# uname -a Linux cubietruck04 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux root@cubietruck04:/var/log# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 10 (buster) Release: 10 Codename: buster Since that upgrade the Cubie is crashing often compared to the last years ( every ~3 days), in the last 3 years I have never observed that. Please help me to find out the issue. From kern.log I see 2 different crash reasons: Jan 2…

Is it possible to return to the old standart motd on armbian jessie sounds like a joke but im an minimal user and when it is possible how can i do this thank you

This simple tutorial to explain ho wto manage the GPIO with the I2C bus and C++ under Netbeans .

Hi. I'm working on it.I tried different systems ubuntu_lxde_desktop vs... Armbian 5.35 3.4.113 desktop board. gives a pink image error like in the photo. h3disp -m 1080p60 -d I've tried h3disp -m 1080p60 -c 1 I've tried h3disp -m 1080p60 -c 2 I've tried h3disp -m 1080p60 -c 3 I've tried but still no image how can i fix it ????

I am having a network problem that I can not figure out. First I had to roll back the kernel to version 5.x to even get wifi to work. Since then I have tried all sorts of things. No matter what I do, when I unplug the eth0 the wifi goes away as well. Here is some stuff that might help. __ __ _ _ _ ____ _____ | \/ | (_) (_) |/ __ \ / ____| | \ / | __ _ _ _ __ ___ __ _ _| | | | | (___ | |\/| |/ _` | | '_ \/ __|/ _` | | | | | |\___ \ | | | | (_| | | | | \__ \ (_| | | | |__| |____) | |_| |_|\__,_|_|_| |_|___/\__,_|_|_|\____/|_____/ Version 1.1.1, based on Armbian 23.02.2 Bullseye Running on OPi 3 L…

Hi! I'm trying to use the image Cubietruck_Debian_3.8_jessie_4.0.4.raw with my CubieTruck, but run into problems when trying to use an external LUKS-disk which is encrypted using aes-xts-plain64. 'cryptsetup luksOpen' informs the following: device-mapper: reload ioctl on failed: No such file or directory Failed to setup dm-crypt key mapping for device /dev/disk/by-uuid/<xxxx>. Check that kernel supports aes-xts-plain64 cipher (check syslog for more info). 'cat /proc/crypto | grep name' lists only this, which seems kinda minimal: name : stdrng name : stdrng name : crc32c name : deflate name : ecb(arc4) name …

HowTo rotate screen(dispaly) 90 degrees on Armbian on OrangqPi PC?

I tested the actual Xenial on my BPP but got a crashdump each time I reboot or shutdown the system. I found, that armhwinfo was causing this crash by removing the module a20_tp. Disabling the line /sbin/modprobe -r $(cut -f1 -d' ' </proc/modules) in /etc/init.d/armhwinfo avoid this problem. This line is part of a patch Thomas Kaiser introduced in October last year. I don't know, if this problem occurs only in my configuration (nothing special, but a connected Lemaker 5" LCD may be the difference), or it is related to the Kernel 3.4.113 only, but it goes reproducably wrong, if this line is active. It cause the oposite of the intention of this patch, because after…

Hi, i just updated my bpi and could not unlock my encrypted luks volumes on a sata hdd. Error message: # cryptsetup luksOpen /dev/sda1 sda1 device-mapper: reload ioctl on failed: No such file or directory Failed to setup dm-crypt key mapping for device /dev/sda1. Check that kernel supports aes-xts-plain64 cipher (check syslog for more info). Following was updated: Start-Date: 2017-04-27 12:05:32 Commandline: apt upgrade Upgrade: linux-image-next-sunxi:armhf (5.26, 5.27.170427), hostapd:armhf (2.5~armbian5.25+1, 2.5~armbian5.27.170428+1), linux-dtb-next-sunxi:armhf (5.26, 5.27.170427) End-Date: 2017-04-27 12:08:01 Is there any way to quick fi…

I've got an Orange Pi Zero Plus running Armbian Bionic. I'm trying to add a virtual wifi interface so I can create a wifi hotspot so I can connect to it easily on remote networks. iw list shows that the adapter *should* be capable of adding an additional interface. This works on other Orange Pi boards I've got but not this one. Any ideas? root@opizero:~# iw list Wiphy phy0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0…

I'm trying, with no success, to make a 3,5 inch tft lcd screen function with an orange pi zero plus (h5) via SPI. I will love if someone could help me diagnose the reason why I'm failing in doing so. The screen in question is a WaveShare knockoff -> link (the pinout can be found at the bottom of the page.) I'm running Armbian buster 5.92 with the kernel 4.19.63 and all packages upgraded. I also have a working serial connection (using the UART pins located next to Ethernet jack on the board) and am using the 'screen' program to communicate with the device. When connecting the screen and turning on the board the leds on the screen turn…

Hi, after the update from Armbian 5.23 to 5.25 on a Banana Pi M2+ board, the MAC address and CPU serial number have changed. This can be reproduced by just updating the u-boot package on Armbian 5.23: # ifconfig | grep HWaddr eth0 Link encap:Ethernet HWaddr da:c7:a0:49:24:d6 # grep Serial /proc/cpuinfo Serial : 2435501d0a0e4800004d # dpkg -i linux-u-boot-bananapim2plus_5.25_armhf.deb # reboot # ifconfig | grep HWaddr eth0 Link encap:Ethernet HWaddr 3a:89:a1:23:98:a6 # grep Serial /proc/cpuinfo Serial : 24005035871c481d0a0e Does anyone know the reason for this? Did u-boot change the way these numbers are generated? …

Nanopi Neo AIr Kernel Module Loading problem when dynamically loading from VirtualBox Built .Ko files.

I have a solar application for PC, so my goal is to reduce the power consumption in idle as much as possible. How would one go about this with the latest armbian distros?

My OrangePi Zero is on 23.02 and I intend to stay with it (unless/until xradio wifi works on kernel 6.x). Just ran apt update and it shows these available packages: armbian-config/bullseye,bullseye 23.08.0-trunk--1-SA9048-Baeda all [upgradable from: 23.02.2] armbian-firmware/bullseye,bullseye 23.08.0-trunk--1-SA1251-B226d all [upgradable from: 23.02.2] armbian-zsh/bullseye,bullseye 23.08.0-trunk--1-SAbfee-Baf88 all [upgradable from: 23.02.2] I'm surprised to see anything related to 23.08 seeing as that version hasn't been released yet, so obviously I don't really understand what it means to be seeing this. Should I go ahead and install these ev…

Ok - first, i'm a noob, - second, I am in over my head. I am attempting to install Plex on my banana Pro - which i did. Up and working just fine. http://www.htpcguides.com/install-plex-media-server-on-banana-pi-with-bananian/ The issue that i'm having is that I am having trouble mapping/mounting a drive. I am using this command but get an error: mount –t cifs //networkip/share /local/linux/folder –o username=usernameonwindowsmachine,password=passwordforwindowsmachine I put in: "mkdir /mnt/nas" - and that works. When I type everything out, it looks like this: mount –t cifs //192.168.1.42/mnt /nas –o username=321barnes,password=Password th…

I've been trying to learn how to do that by looking at the [leds_para] in https://linux-sunxi.org/Fex_Guide#.5Bleds_para.5D but the [leds_para] in the script.bin of my Orange Pi PC are very different: [leds_para] leds_used = 1 green_led = port:PL10<1><default><default><1> green_led_active_low = 0 red_led = port:PA15<1><default><default><0> red_led_active_low = 0 I'm lost... Can you help me? It's an Orange Pi PC with ARMBIAN 5.60 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i Thanks.

Hello community, Kernel 4.3.x should have support for DMA engine on A20 boards, see: http://linux-sunxi.org/Linux_mainlining_effort#Merged_into_4.3 Does / should this also improve the SATA write performance? After update to kernel 4.3.3 from apt.armbian.com I cannot see any big write Performance increase... thanks for comments... best regards and a happy new year... holsteiner

Hi guys, I have a problem ... accidentally deleted by their stupidity network-manager package .... please if anyone can help, please upload the package for opipc + (armbian 5.20) in advance thank this good man!

I just downloaded the most recent mainline image for the NanoPi Neo (Ubuntu_xenial_dev_nightly.7z). It boots and runs fine. However, I was trying to access the UART1 on /dev/ttyS1, but apparently it is not enabled by default.The dmesg output is: dmesg | grep tty [ 0.000000] Kernel command line: root=UUID=d9678417-38b4-4c2b-993e-04cdea0247de rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=eeb8ef06-01 ubootsource=mmc sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 [ 0.000973] console [tty1] enab…

I run into problems trying to get application distributed via snaps installed. Mount snap "core" (3751) [ 1691.207676] squashfs: SQUASHFS error: Filesystem uses "xz" compression. This is not supported error: cannot perform the following tasks: - Mount snap "core" (3751) ([start snap-core-3751.mount] failed with exit status 1: Job for snap-core-3751.mount failed. See "systemctl status snap-core-3751.mount" and "journalctl -xe" for details. Found out kernel module would need to enable CONFIG_SQUASHFS_XZ. Could someone help me by adding the module to Kernel or support me in doing so or w…

Hi everyone! Follow instructuions https://linux-sunxi.org/Sunxi-Cedrus to setup hw decoding everyone need kernel with flags: CONFIG_MEDIA_SUPPORT CONFIG_MEDIA_CONTROLLER CONFIG_MEDIA_CONTROLLER_REQUEST_API CONFIG_V4L_MEM2MEM_DRIVERS CONFIG_VIDEO_SUNXI_CEDRUS Images from armbian repo is without one of them - CONFIG_V4L_MEM2MEM_DRIVERS So my proposal is to make kernel for desktop prebuilds with this flag, if its possible ofcourse. Im understand that is opensourse project, so my help can be like that - i have really much space on Y.Drive and i can share folder to minimize download usage of armbian repo.

I switched mentioned pins to IN mode. And it is seems they are pulled up by default. +-----+-----+----------+------+---+-Orange Pi+---+---+------+---------+-----+--+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.0 | IN | 1 | 3 || 4 | | | 5V | | | | 11 | 9 | SCL.0 | IN | 1 | 5 || 6 | | | 0v | | | If physically connect that pins to the ground it shows 0 level. But I need it 0 by default. A…

Hi all, I am using an Orange Pi PC PLUS2 with everything in the emmc for controlling another device through a serial connection (rs485) with a serial converter using FTDI chips. I am using docker containers to embed my application and easily deploy/share it. using uname -a gives me: Linux host-test 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux The problem is that randomly I get the following error: [135431.500807] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate [137213.011801] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate [138650.664850] ftdi_sio ttyUSB0: ftdi_set_ter…

I have simple Banana Pi. I have Armbian on it installed on Feb this year. I can see in Changelog that there were no kernel updates for this (A20) board. Will there be any kernel updates? And when?

Hi, I have an Orange Pi Plus 2e and I've installed Armbian_5.59_Orangepiplus2e_Ubuntu_xenial_default_3.4.113_desktop. I need to play four hd videos at the same time. I could do it with Raspberry pi3 model B with 720M GPU memory. I played videos with MPV with X11 but couldn't play with VPDAU. It is just played only one video. What can I do? Can I set GPU memory? Thank you.

It boots but does not recognize USB keyboard input. Not possible to login.

I have a wifi dongles that aren't showing up with the usual wlan0/1 identifier, below is what I've discovered so far, but if anyone can shed some light on this, I'd be much appreciative. ifconfig -a I get the following: wlx20e816006af8 Link encap:Ethernet HWaddr 20:e8:16:00:6a:f8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 TX bytes:0 (0.0 if I do iwconfig wlx20e816006af8 essid myhomesid channel 6, I get no errors, however, when I do the iwco…

Where are the old-ish Armbian Jessie downloads for the Orange Pi PC? I can't find them anywhere!

hello dear all, good day dear Armbian-experts recently i have managed to get Armbian up and running on a Banana Pi. I was very very glad. now i am digging deeper into the system and try to learn all the necessary things. regarding another system: on orange pi -pc i want to install armbian - from this page https://www.armbian.com/orange-pi-pc/ i fetch Armbian Stretch mainline kernel 4.14.y Server or light desktop usage scenarios. Stable question: can i upgrade after the installation the system to the newest kernel... ?!? Is this possible?

So I have a weird problem that I haven't seen yet, so forgive me if its already been answered. But for some reason mainline kernels (bionic and stretch) both bootloop at the same place. Seen below: The board boots perfectly fine on legacy kernel though. I'm using decent quality Samsung SD cards, and I've tried every combination of usb cable/powerbrick as well as the barrel jack so I'm not sure what the snag is.

I noticed that the orange pi win plus does not have a sata port connector. Is there a way to attach a sata ssd/hdd to the orange pi win plus through the gpio pins?

Hi, I have two questions: 1. Where can I download the latest image for my board? rom this forum entry I see there is no armbian image for the first Orange Pi? The link https://www.armbian.com/orange-pi/ doesn't work, as it redirects to https://www.armbian.com/orange-pi-plus/ which is definetly not the same (A20<>H3) 2. After doing a 'firmware upgrade' from armbian-config, it identifies itself as a Banana-pi. Is it normal? The MOTD is BPi and armbian-config shows BananaPi as well.

Hi everybody and thanks the armbian team for your work. I'm owning a SOPine module (SOPine-A64-Rev C) with a SOPine Baseboard (Model A Rev B), with the 16Go eMMC module sold by Pine64. I tried these builds with the same issue: Armbian_20.02.1_Pine64so_buster_current_5.4.20.img (All the provided logs are from this build) Armbian_20.02.1_Pine64so_bionic_current_5.4.20.img Armbian_19.11.6_Pine64so_buster_current_5.4.7.img I tried at first to write the image direclty to the eMMC before noticing it wasn't the right way to do => I removed all the partitions from the eMMC. When writing the image to the microS…

I use "./compile.sh BRANCH=default BOARD=orangepilite KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=xenial" to build the whole booting image for my orangepi lite, it works very good as the official prebuilt armbian image. Here, the usb otg port seems configured as peripheral mode already( g_searial module works as gadget in fact), I can use it as usb seraial well. However, I want to make it works as a usb storage, so, I though the g_mass_storage was the right module. I loaded it using following command: insmode g_mass_storage.ko file=/dev/mmcblk0p1 removable=1 then, I got kernel message like: [ 194.842091] usb open ba…

Hi, I've installed armbian on my orange pi +2 and trying to build GrandOrgue. It is depending on the wxWidgets library. I've tried searching apt-get without any luck. Any suggestions? Thank you. -Roy

Hi all, I'm currently running Armbian 5.36 Ubuntu 16.04.3 LTS 4.11.1-sun50iw2. This was / is a local armbian build that I performed a few months ago to resolve an issue that I saw at that time in the network stack that prevented ipsec working correctly. I've performed apt update / apt upgrade since however cat /proc/version still reports the version as that which I manually built back in June. Fast forward to today and I'd like to try out some traffic shaping tc rules but I'm running into some difficulty, which is making me doubt if my kernel has the support needed for iproute2. The following works without any issue to list existing rul…

Hi! I just installed a fresh Armbian_5.14_Lamobo-r1_Debian_jessie_3.4.112 image to my R1. While booting, the system first shows about a page of boot-messages on the Display and then changes to a Out-of-Range Display. Changing console by <Ctrl><Alt><F1>, ...F2,... Fn doesn't help. Accessing the system with PUTTY/ssh works fine. apt-get update/upgrade/reboot won't help. The display does 1280x1024 resolution maximum. Just before I used banian without any problems. What should I do?

I'm using Armbian 5.27 with BRANCH=default BOARD=cubietruck RELEASE=jessie BUILD_DESKTOP=no Sometimes bluetooth fail to start, are there some way to fix it? Leonardo

Hello, I am using OPI one with Armbian_5.90_Ubuntu_bionic_4.19.57, so I fliped my 7" touch screen display vertically (rotated 180) by modifing: /etc/X11/xorg.conf/01-armbian-defaults.conf and it worked, but the touch doesn't correspond with it (still points as it was before rotation). how can i flip the touch information (x,y) coordinates vertically (rotate by 180)? Regards,

Good day Armbian Forums! I'm having some trouble with builds of Armbian (up to and including 21.08.6 | kernel 5.10.60-sunxi) seeing wireless access points that are configured to channels 12 & 13 on my Orange Pi Zero Plus2 boards (H3 + 256mb RAM). Specifically, the default Android image (a generic Chinese-language Android multimedia system) that's loaded onto these boards can see and connect to access points that have been set to all channels (1-13) successfully, but any Armbian image I have tried fails to see anything (and subsequently cannot connect) to routers on channels 12 & 13. Due to the nature of this, I believe it may be a region setting or dri…

Hello fellow Armbianers! I'm using Orange Pi zero. My only complaint is the 30s boot time. Looking at the log files, seems like it only takes 5 seconds to boot once the kernel is loaded. The majority of this 30s is spent in uboot somewhere? Does anyone know how to speed up this boot process? I'm always just booting from SD card, don't need USB boot/network boot, console, or any of that. Thanks!

Hi! I need some help in order to install Node-RED over Armbian Wheezy on Cubieboard1 can anyone give me help?

I've tried to downgrade the kernel with the armbian-config tool, but now the opi+2 hangs while booting from emmc. I can boot via sd card, but i dont know how to fix the problem - please help.

Hello, The system changed to ro during update. The armbianEnv.txt file has been corrupted and is empty. I'm looking for how to create it again ... and I can't find it. Can you help? edit: I try to do it myself, but I don't know if that's all. verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay-prefix=sun7i-a20 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u edit: Overall, there were no problems at 5.3.9. During the update to 5.4.20 I broke down. The worst thing is that I'm not in the location : / edit: Search result: it's ok ?

As you known OrangePi PC PLUS with armbian (e.g. Armbian 22.05 Jammy) can't be fully off. (But Xunlong's Ubuntu 16 can be off ok) I suggest change status of board from green "Supported" to yellow "SUITABLE FOR TESTING (WIP)".

i'm just insert usbflash, rightclick mouse on icon usb flash and select "Mount" hardware: Orange PI PC v1.2 image: Armbian_5.05_Orangepih3_Debian_jessie_3.4.110_desktop

Hey, for the LEDs the option "disk-activity" which was possible in Wheezy Legacy is no longer available. Is it possible to re-add that? Thank you, Ingo Fischer

Hello Community, I want to take a look at Wireguard, now I heard that that Wireguard is supposed to be already integrated in the Kernel of Armbian. Is this actually correct and if yes how do I please active it? Thank you, blub4747

Hi there! I has a OPi zero board on armbian ubuntu os. There is a python scrypt that ping server. Scrypt starts with my service. service code: [Unit] Description=My Script Service After=multi-user.target [Service] Type=simple ExecStart=/usr/bin/sudo /usr/bin/python /root/test/qr2.py RemainAfterExit=no Restart=always RestartSec=5 [Install] WantedBy=multi-user.target python ping server like: try: os.system('ping ' + ip + ' -c 4') # or # s.scall('ping ' + ip + ' -c 4 ) except: print 'ping error' Sometimes If i start system after power supply scrypt is starting, but then hangs on ping function. In Htop (image) i can see ping process. There are …

I have been trying to get USB OTG to work for the past few days, but have not succeeded. I have enabled all of the appropriate kernel settings according to this. I modprobed sunxi and g_ether, but my laptop did not detect the Orange Pi (no change in lsusb). My laptop runs Arch Linux, if that matters (the image was built on a Xenial VM though). There is no dmesg output about this, so I do not know what I did wrong. The reason I need the dev kernel is because I am using docker.

Hi, I'm running Armbian Stretch with the 4.14.y kernel on my Orange Pi Zero, as a headless Samba server. Does anyone have a link to a tutorial on how i can add a GPIO button to run the shutdown command, so I don't have to SSH into it every time I want to shut the thing down? thanks.

Hi everyone, I am using an OrangePi Zero with AllWinner H2+ and I need to catch UART1_TX and UART1_RX interrupts. I have been reading the Allwinner H2+ datasheet (http://wiki.friendlyarm.com/wiki/images/0/08/Allwinner_H2%2B_Datasheet_V1.2.pdf) and I have seen that UART1 interrupts are mented on PG_EINT (section 4.22.2.46) and UART Register Description (section 8.3.5) - I have no clear which registers I should configure to detect the UART1 interrupts, and how to do it. For example, for detecting Received data available, I think I should: - Enable the ERBFI bit in UART_IER register - Check IID field in UART_IIR to de…

Hi Do You know if there are any problems with deploying armbian on cubieboard 2 with TSD instead of NAND ? Do I have to change anything on the system side or is it transparent ? Adam