Allwinner sunxi

I read few in the net about the ahci-driver of the A20-Board. I have a Cubietruck and I want to use a hdd with more than 2TB. Is it - theoretical or in principal possible? My HDD is found but only 2TB of it.

Dear all, I am using armbian Mainline Debian Jessie 4.9.7 and 4.9.12 on a Banana Pi Pro (A20). Coming from legacy and fex, I came a long way learning a lot about Device Trees, Overlays, etc. the last 2 weeks. I even compiled some dev kernels to experiment. I currently struggle with with the OTG port. I have two devices on the primary slots and need to get the OTG in host mode to attach my third device. I've read that the OTG is not providing 5V to the device. Therefore, I use Pin4 5V DC and Pin6 GND of the 40Pin header. It works well when connecting Device #3 on USB 1 or 2. But not on OTG. I used dmesg to track devices. Is there an…

Apologies if this is documented/reported somewhere else, but I can't see anything on a quick forum search. I received two Orange Pi Zeros this morning, and eagerly downloaded the Orange Pi Zero flavour of Armbian (Xenial Legacy) and loaded it up on a good 8GB microSD. I then started using it, updating it, and suddenly realised that it only had a 1.4GB partition when it failed to finish updating due to insufficient space. I thought since I'd had some issues logging into it that I might have interrupted the first boot resize, so I re-imaged it, and loaded it up, left if five minutes, and then logged. No cigar... says it is still 1.4GB (1.4GB size, 1.2GB used, 2…

Hi Does anyone know if the OPi Lite's WiFi is meant to automatically reconnect if the AP reboots or disappears and then comes back? What is the default behaviour supposed to be? Is it meant to automatically scan nearby networks? Thanks

Good afternoon. I have an Orange Pi One and I need to achieve the maximum boot speed. The ultimate goal is a kiosk mode and the only application on the QT. The network is not needed. The simplest way will probably be to change the run level to the single mode, but with this there are problems. Any tips, suggestions, experiences?

Just stumbled upon this new board by the Friendlyarm folks. http://www.friendlyarm.com/index.php?route=product/product&product_id=197 Lots of signals exposed on the strip contacts, including Ethernet and USB, though magnetics and connectors aren't there, which makes this even more interesting to build thin appliances: you add connectors when you need them. Good! I'll probably order a couple to start playing with, but will take forever to ship over here.

Is there currently a known problem with some of the Repos used by H3 Armbian Mainline (OrangePi Plus 2). For the last few days, when I run apt update, I get timeout messages on some repos. The repos that are consistently timing out are: http://ports.ubuntu.com xenial InRelease http://ports.ubuntu.com xenial-updates InRelease http://ports.ubuntu.com xenial-updates/main armhf Packages Additionally, this Repo sometimes times out, and sometimes succeeds, but takes a long time: https://deb.nodesource.com/node_6.x xenial InRelease Please let me know if you require more info. Many thanks, Roy Gilby

Hello everybody. Faced such a problem. When connecting to the HDMI port of the monitor, no image is displayed on the monitor. More precisely, the line at boot time is visible, but the desktop is not displayed. If you connect to a TV via HDMI port, there is an image. I connect OrangePi Plus 2, via HDMI-HDMI cable. Monitor LG FLATRON 27EA33V-BB. Why is that such a problem on armbian and retroorange assemblies. But the assembly of DietPi on the monitor image displays .. The systemist under win7 also without any problems displays the image always. Tell me where to find the solution to the problem. I tried changing the modes with the 'h3disp' utility. Screenshot - https:…

Hello. Has anybody tried to encode h264 on h5 via ffmpeg cedrus264? any help would be appropriated. thanks in advnace.

Hi, I have a Opi+2 board which has an Armbian system installed in its emmc. Now I want to format its Emmc and reinstall Armbian but the problem is I don't have a proper SD card. So I need to do it without an SD card. I have a running system on it, so I can reach the working system. Is there a way of formating it while its running? For example a command does the same thing with "dd if=armbian.img of="/dev/mmcblk1"" (which won't work while there is a system working, its just an example) (mmcblk1 = working system, emmc)

Hi, At the beginning I would like to emphasize that I am not an expert in linux :) I use bananapi m2 + v1.1 in my project. Until now everything worked well with the SD card on armbian 5.25. My project is now finished and would like to run the system from emmc. I used armbian-config to move system from SD card to emmc. I chose the only option: Boot from eMMc – system on eMMC. Everything went well except the message (while formatting): EXT4-fs (mmcblk1p1): Unrecognized mount option "compress-force=zlib" or missing value mount: wrong fs type, bad option, bad superblock on /dev/mmcblk1p1, missing codepage or helper program, or other error In …

Hi, Please, i am seeking for some help. Today i just did an apt-get dist-upgrade and my banana pi updated the kernel to 4.19.13. There wasnt any error messages but then i wasnt able to boot. I get messages like "/boot/zImage file not found" so i checked my sdcard (wich cointains the boot folder) and i saw that zImage was symlink to the previous kernel image (wich no longer existed). I corrected it cause in fact there was a vmlinuz-4.19.13-sunxi but there are some more symlinks broken in boot foolder. UInitrd is also broken and i dont have the appropiate file to make a new symlink, script.bin symlink is also broken (it pointed to /boot/bin/bananapi.bin wich …

Orange Pi PC+ installed Armbian Bionic mainline kernel 4.19.y, Armbian Stretch mainline kernel 4.19.y not working sound via HDMI, on an older version Armbian Xenial desktop legacy kernel 3.4.y sound via HDMI works. What to do to make the sound work in the new version

Hi in the last build of 17/05/2019, https://dl.armbian.com/orangepi3/nightly/Armbian_5.87.190517_Orangepi3_Ubuntu_bionic_dev_5.1.0.7z armbian won't boot and there are a black display My board is a opi3 2gbram + mmc 8GB The board is working, because in the mmc, I have installed an old version (5.82) and I can bood from the SD card with android 7 get form here: http://www.orangepi.org/downloadresources/OrangePi3/2019-01-23/orangepi3_0e7dae8bb1bf9678fda5754272.html I tried to connect via ssh from another computer, and it's works, I login, changed the default passwd, but after 1 or 2 minutes, the opi3 reboot and from th…

Last night I downloaded "https://dl.armbian.com/orangepiplus2e/Debian_buster_next.7z" (OPi+2E) ... burned it to SD card and fired up the board ..later installed desktop and other software ...BUT when I was installing MPV I observed that few files with "Vulcan" in their names were also installed...so does that mean that mainline next 4.19.xx images for H3 are now fully suitable for multimedia desktops with Hardware graphics/Video acceleration fully supported ?

Hello, I've just found a topic about removing Allwinner legacy. I work with Orange Pi PC Plus board, H3 CPU. Do I understand correctly that the option to build system based on old v.3.4 kernel will be removed? Once I experienced a problem with system shutdown using newer kernel - got System halted message. This is why I decided to continue with legacy kernel. Please advise.

Hi, We are using trying to use Banana PI M2+ for our application , we mainly use UART and Ethernet on module. uname -a details are below. Linux bananapim2plus 5.15.74-sunxi #22.08.6 SMP Tue Oct 18 07:00:33 UTC 2022 armv7l armv7l armv7l GNU/Linux We Enabled UART 3 by adding below command line on /boot/armbianEnv.txt as overlays=uart3 Pin Number: 8 & 10 We can able to transmit and receive data for uart3. We need to enable one more UART to communicate, We tried overlays=uart2 , We failed to enable, Can anyone guide us to enable one more UART in Banana pi M2+ Regards, …

I just tried out kernal 4.1.4 and whenever I try to boot (first run) I get a kernal panic just before the automatic reboot. After the reboot, the same process occurs. Tried Debian wheezy, Debian jessie and Ubuntu Trusty kernal 4.1.4, build 5.8.2015

I have a BPI-M2 and I am trying to patch kernel 4.4.1 with contents of archive patches-4.4.1-rt6.tar.gz for RT-Preempt while making Debian Wheezy xfce desktop image. I have tried putting patches in /userpatches/kernel/sunxi-dev and /userpatches/kernel/sunxi-dev/linux-vanilla/v4.4.1 nether worked. Made image but patches were not applied Any help would be appreciated Tim

I want to install debian or armbian or what ever it is for Orange Pi One to be a server. I downloaded Jessie server from here: http://www.armbian.com/orange-pi-one/and extracted the 7z file. I do now know what to do with the raw-files I extracted. At first I tried to install install basic Debian from here: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=342&extra=page%3D1 but I didn't undestand the instructions after mounting SD Card FAT partition. I'm not even sure am I suppose to mount it to Orange Pi or the PC I used to write the image to th SD. So I went looking for another way and found the first mentioned which was seemed to be made …

Hey everyone, First off, I don't use Linux often so please bear with me if I miss out on obvious things. I have a few Orange Pi Lite boards, and after booting up Armbian 5.14 I was excited to give the Wifi a try after only having ethernet on my Orange Pi One boards. My OPi Lite sees my network just fine, but when I put in my credentials and go to connect to it, it fails returning "Bad Password". For what it's worth, I've checked the password probably 25+ times, I promise it's right. The wifi WILL connect to open networks, however. Is there some obvious solution that I'm missing here? Any help or direction would be appreciated. Thanks!

Hi first of all sorry for my bad English .I have an OPI PC + ,I install Ubuntu on my sd card and after boot i used nand-sata-install command to use may nand but when i tryied to use my sd card (after format sd card) it did't work and after reboot i receive "panic= boot argument" how can i use my sd card and mount it when my dist installed on nand? even i checked this link for Cubietruck but it wasn't useful for OPI , and then i checked this and it was really hopeful but I don't now how can i exactly implement this .Actually I need to auto mount my sd card as a result when I reboot my OPI PC + I need my OPI boot from emmc instead of sd card. thank you for you…

I just booted up a fresh install of Armbian 5.24 (Armbian_5.24.161128_Orangepizero_Ubuntu_xenial_3.4.113) on my Orange Pi Zero and I can't seem to get IPv6 working. It worked fine on Armbian 5.22. It's like the dhclient command isn't able to set the address or the address is silently getting dropped or something. Setting ipv6 address via dhclient fails for both eth0 and wlan0. I ran dhclient by hand to see if a problem would be listed in the output but there's nothing: root@orangepizero:/var/lib/NetworkManager# /sbin/dhclient -d -v -6 -N -sf /usr/lib/NetworkManager/nm-dhcp-helper -pf /var/run/dhclient6-wlan0.pid -lf /var/lib/NetworkManager/dhclient6-1cfb9f48-cd01-41…

Hi, I was on the legacy kernel until recently with my bananaPi M1. I switched to the vanilla kernel but since then, when I try to use the GPIO python library (for bananapi from LeMaker github), it works quite well except for functions gpio.add_event_detect() or GPIO.wait_for_edge(channel, GPIO.RISING) This usually disconnect my network and the event is never detected. I have to reboot the PI to restore the state. Also, a normal read/write state GPIO.input(PIN_NUM) works perfectly... I assume it is due to the vanilla kernel but could not find any documentation on why this is happening... Any answer/comments would be much appreciated! Let me know if yo…

Hi, No real problem, just a question. I'm using latest Armbian Jessie 5.25 with my good old Banana Pi. root@marvin:~# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 144000 312000 528000 720000 864000 912000 960000 root@marvin:~# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq 480000 root@marvin:~# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq 960000 Please notice that 480MHz (the min freq) is not in the available frequencies. So that gives the following output with cpufreq-info : root@marvin:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kerne…

- A64 - strange naming "win"

I installed the SoftetherVPN using the script provided in Armbian distribution, than I configured it from my windows machine, using the VPN Server manager application downloaded from softether website. When I try to connect from my iPhone I get an error "The L2TP-VPN server did not respond. Try reconnecting. If the problem persists ..." What I didn't do , is opening ports in my router, do I need to forward 443, 992, 1194, 5555 to my BananaPi IP in my router ? Some more details I posted on the softether forum, but it seems there is noone around to answer, and alot of spam is posted daily Thank you. VPN Tools>check Check command …

Hi all. I followed this tutorial and I got the AP and client mode working. wlan0 using the onboard wifi as the AP and wlan1 using a usb dongle as the client connecting to my wifi network. But when I connect to the PI and got an IP address via dnsmasq I am not able to get to the pi its self. I can not access anything on the PI. I have a web server running on it. How do I get to the services on the Pi it self via the AP I created. Basically what I want to do is have the client connect to the wifi network if there is one or if the pi is in range of the wifi network. But then if there is no network then I want to connect to the…

I came across a spi clk problem with my Orange Pi One. A similar unanswered question has previously been asked for Orange Pi Zero, but I started a new topic because of the new board. I am using ARMBIAN 5.32.170913 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i Everything is set up properly and spidev0.0 is created and working. Following is my /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 fdtfile=sun8i-h3-orangepi-one.dtb overlay_prefix=sun8i-h3 rootdev=UUID=a2df1e68-90c9-46a0-ab26-169cb43e35c8 rootfstype=ext4 overlays=spi-spidev i2c0 uart1 uart2 uart3 param_spidev_spi_bus=0 param_spidev_spi_cs=0 verbo…

Currently, There is no mainline release for Orange Pi One. The only release of mainline is in nightly build folder and the kernel version is v4.11.8, which doesn't work SPI chipselect. On armbian latest source compiled image, v4.13.9, SPI problem is solved. Do you have any plan to release official mainline image for Orange Pi One? Thank you very much.

Hello everyone. I encourage you to write these lines after I spend all day reading and trying to solve the problem without success. Knowing that there are other many post about, I write this new that existing ones are already very old and refer to applications and concepts that no longer exist in the latest versions of ARMbian. The fact is that I bought a new OrangePi Lite with a new SDHC Clase10 (80MBs) SanDisk and basically not I connect to the WIFI 2.4 g connection of my house where work perfectly without any problems other Zero OPI and OPI PC + with ARMbian 5.35 Ubuntu. The summary problem is it asks me again the password and does n…

Hello everyone. I would like to create an update system, which via a link on a web page, will check on an ftp server and if a version is newer, download the img file and install it. it is the installation part that poses me big problems. to write an img on the sd we must use the command dd if = ..... of = ...... But since the sd is used it does not work. I had thought of going through berryboot but a priori it is not functional on the m2. If someone has an idea thank you

Hello, I'm following this project : I was recently spending time on the activities to do with children, 3D printing and robotics, and in order to be able to try to follow https://docs.armbian.com/Developer-Guide_Build-Preparation/ i have bought a new laptop which respect the requirements (SSD, ram...). So now my next goal is to try to make a custom version of armbian dedicated to the schools. To start, for the first step, I would like to try make a localized version of armbian in French by default, in order to be more easier for the French speaking user. With the new evolutions of armbian for OrangePiPC+, there is an ubuntu…

Hi, I just downloaded this image from here (this is the link i copied from the bananapipro site): https://dl.armbian.com/bananapipro/Debian_stretch_next.7z and i got Armbian_5.38_Bananapipro_Debian_stretch_next_4.14.14.7z on my disk. Unpacked it and put it on my sdcard with etcher. Tried to mount it as loop device --> error. Checked with gparted --> it said /dev/sdc1 is not ok. Repaired it with gparted and could mount it. Put it with etcher on the card. --> Bananpipro does not boot. Red light is the only one that shows up, none of the other led is blinking. What can i do? best regards Ralf

Can you power an Orange Pi Zero or Orange Pi One from the 26/40 pin header ? I am pretty sure the answer is yes as the OPI Zero expansion board has a power jack. But is there any information regarding how to do this ? Do you feed the +5v or the +3.3v Is it the same for all of the RPI compatible headers ?

I've formatted the opi+2 card I have using recovery and now I get ping screen. I use a 1280x1024 screen with a DVI converter. I tried the HDMI cable using a 1080p TV and it worked without issues. I also tried "h3disp -m 33 -d" "h3dsip -m 1024x768 -d" "h3disp -m 33" and so on. None of them worked. Here is a system output (used armbianmonitor -u) http://ix.io/1iWN !! I noticed this output when used dmesg command: [DISP] disp_ioctl,line:1584:para err in disp_ioctl, cmd = 0x0,screen id = 65536

I had to resolder the pins of the debug port on my NanoPi NEO Air and must have damaged the RX connection as I am unable to send commands but can receive read the debug output fine. Is it possible to change the debug port to UART1 or create another root terminal at another serial port?

Hút bể phốt số 1 hn – địa chỉ nào tốt nhất Tại Hà Nội hiện nay, tình trạng tắc nghẽn, đầy bể phốt thường xuyên diễn ra gây ảnh hưởng nghiêm trọng đến cuộc sống sinh hoạt của người dân. Một trong những giải pháp tốt nhất trong những trường hợp này đó chính là sử dụng dịch vụ hút bể phốt của đơn vị hút bể phốt số 1 hn - Công ty hút bể phốt Avico với chất lượng dịch vụ hoàn hảo nhất. >>> Mời các bạn xem thêm về Dịch vụ hút bể phốt tại quận Hoàn Kiếm Avico : https://hutbephottaihanoi.vn/hut-be-phot-tai-hoan-kiem/ Những lý do khẳng định Avico là đơn vị hút bể phốt số 1 hn Trên thị trường hiện nay có vô vàn đơn vị cung cấp đến với người dùng trên thị trư…

According to the specs of the OP PC Plus, it only supports 32GB micro SD. My only 32GB that I have, that I was booting from on the OP PC plus eventually got corrupted, and will not boot, can't format and install armbian or anything. What are my options? Can I somehow boot from a 64GB micro sdcard, or USB from a fresh armbian image write?

Hello, Wish a good health everyone nowadays! I'm using Orange Pi PC Plus with small aluminium heatsink running Armbian Buster (mainline kernel 5.4.y). SD Card is Samsung EVO Plus 32gb. The CPU governor was set to 480 to 1200, conservative. The system are fresh, just after install. After ~5 minutes of idle uptime temperature comes to 85 and up. Is that heatsink are not good enough? And the second issue I've faced - too quiet sound output from AV-out. The most quiet is Chromium, it is nasty quiet. Sound from local video files in mpv player are bit(2 times) louder both from mp4 and webm, also mp3. Have not tested HDMI(because my…

When I try to read the input on PA19 immediately goes to "1" even though there is no voltage being sent to the pin. Example: #!/usr/local/bin/python from pyA20.gpio import gpio from pyA20.gpio import port pin_to_circuit = port.PA19 gpio.init() gpio.setcfg(pin_to_circuit, gpio.OUTPUT) gpio.output(pin_to_circuit, 0) gpio.setcfg(pin_to_circuit, gpio.INPUT) print(gpio.input(pin_to_circuit)) I don't understand why this would put "1" with nothing even connected to the PA19 pin? Are there some settings I need to change to get PA19 working as a normal GPIO pin?

Hello, I have a Orange Pi One Plus. It has an onboard mic. No matter what i do i cannot record sound from it. Please help, how can i record sound from onboard microphone? marko@orangepioneplus:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepioneplus BOARD_NAME="Orange Pi One+" BOARDFAMILY=sun50iw6 BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=d485420c00 VERSION=22.08.1 LINUXFAMILY=sunxi64 ARCH=arm64 IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=stable marko@orangepioneplus:~$ uname -a Linux orangepioneplus 5.15.63-sunxi64 #22.08.1 SMP Tue Aug 30 07:11:56 UTC 2022 aarch64 …

The problem seems to be kernel version 6.1.30; Just writing image file 'Armbian_23.5.1_Nanopineo_bookworm_current_6.1.30_minimal.img' to SD-card gives the following output via serial console: U-Boot SPL 2022.04-armbian (May 27 2023 - 19:27:28 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.04-armbian (May 27 2023 - 19:27:28 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 33 devices, 12 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: seria…

Hello! I am on the forum to ask you some questions that I am not able to find the answers to. I bought a 3D printer kit on Aliexpress.com including an Orange pi 3 LTS board. On the card there is an operating system installed and several applications for the printer. The first problem is that: I would like to activate WIFI on the card. I tried to do this via 2 different ways. The first is with the following command sudo orangepi-config. I go to the network/wifi menu. I chose my WIFI network. I enter the network key and I receive the following error code: Could not activate connection: Activation failed: IP configuration could not be reserved (not available addres…

When doing apt-upgrade to get the latest linux-jessie-root-cubieboard2, it fails with this error message: # apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: linux-jessie-root-cubieboard2 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 3 not fully installed or removed. Need to get 0 B/1.810 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue? [Y/n] Y (Reading database ... 51863 files and directories currently installed.) Preparing to unpack .../linux-jessie-root-cubieboard2_5.00_…

Hi, I've installed Armbian 5.0.4 Wheezy. I'm trying to configure the sound, but no success jme@cubieboard:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 jme@cubieboard:~$ cat /etc/asound.conf pcm.!default { type hw card 0 device 0 } ctl.!default { type hw card 0 } jme@cubieboard:~$ speaker-test -twav -c2 speaker-test 1.0.25 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Rate set to 48000Hz (requested 48000Hz) Buffer size range from 128 to 131072 Period size range from 64 to 16384 Using max b…

Hello to all, how can I upgrade the kernel to 4.6.2 from 4.5.2. I have a lamobo r1? Thank you Paul

Hi I have problem with Cubieboard2 powering off during Legacy Armbian_5.14_Cubieboard2_Debian_jessie_3.4.112 boot. It had been explained a little bit here: http://forum.armbian.com/index.php/topic/1178-cubieboard-1-legacy-boot-failure/ So maybe I need uBoot upgrade. I had written SD card with command: dd if=Armbian_5.14_Cubieboard2_Debian_jessie_3.4.112.raw of=/dev/sdd bs=1M and upgraded uboot from here: http://phelum.net/temp/CB2/u-boot-sunxi-with-spl.bin with command: dd if=u-boot-sunxi-with-spl.bin of=/dev/sdd bs=1k seek=8 full boot output here: U-Boot SPL 2016.05-12902-g0e6e34a-dirty (Jun 19 2016 - 21:55:16) DRAM: 1024 MiB CPU: 912000000Hz, AXI/…

I'd love to backup my X2 before I start to mess it up just to have a restore point somewhere at the start. Is it possible with a live linux and dd if / of?

Hello, I've downloaded and installed armbian for Orange Pi PC (debian legacy), and it boots ok. When trying to shutdown using systemctl shutdown I get "kernel panic - not syncing - Attempted to kill init - reboot in 10s", and i'm unable to see more info. I have installed the OS in the past(3 months ago) without any kind of problem. I appreciate any help, Thanks

Good day. I've purchased lcd 5'inch LCD. I have some troubles with HDMI connection (no image), but i fixed it using this topic: link. (drivers at disk doesnt take any effect) But i can not run touchpad. I used different hints but god no effect board - Orange Pi PC Plus kernel 3.4.113-sun8i module ads7846.ko at /lib/modules/3.4.113-sun8i/kernel/drivers/input/touchscreen My script bin: Spoiler [spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3&g…

Just got compiled a new OPi PC, Ubuntu desktop, Armbian 5.36 with mainline 4.14.3 kernel, image. The on-board codec sound though is just at a whisper level no matter what, it looks its there but barely heard at all. Can we fix that?

Hi, I'm trying to use the rbd Kernel module but it is somehow missing: root@node1:~# modprobe rbd modprobe: FATAL: Module rbd not found in directory /lib/modules/3.10.107-pine64 How can I load this Kernel module? It's Armbian 5.43.180418 on a OrangePi Win Plus. Best, Tobias

Hey guys, first off, I'll make no bones about it... I'm an absolute noob. But I wanna learn! So I have the OPi PC and I purchased this 7" HDMI USB touch screen Now, I've plugged it all in and the screen worked fine right out of the box but the touch did not. I've verified it's working by plugging it into my desktop and everything worked great. I can only assume that it's not working due to a lack of drivers. The screen came with a CD that contained the screen drivers but not the touch drivers. It also came with a handful of RPi distros with the drivers preinstalled. But nothing for OPi Can anyone offer some suggestions?

Hi, I am trying to write a program which will detect the presence of SD Card in Nano Pi M1 plus device. There are many ways to do this either by doing fdisk -l or looking into /dev/mmcblk* . But I want to keep running it in a loop and doing fdisk -l and grep doesn't seems an appropriate way. Can the insertion or removal of SD cards be checked via Hardware Interrupts? Plz. help me I am a newbie.

I have a cubietruck at my cabled network (RJ45). Using Ip Scanner tools, I only find it by MAC address. The manufacturer name have nothing, how can I put a manufacturer name to help me find it? Other computers show their manufacturer names.

Hi I have an orange pi 3 board ,I want to turn on and use 5v cooler fan that uses GPIO ( pin 2 and pin 4 ) , how can I do that? thank you

Hi all. I'm new, so don't hit too hard. I'm interested in how the NAS Dock for NanoPi Neo2 is defined in the system. I want to install OpenWRT, because I need a NanoPi based router. Armbian seems to me too complicated for such tasks. If you put OpenWRT on NEO2, then NAS Dock is not detected in the system. At that time Armbian determines, I can easily open the HDD or connect devices to the dock's USB port. Please tell me. Which module or driver is responsible for the dock to be defined in the system? The Openwrt forum has not yet been able to help me, so I'm writing here. Help as you can. Скрытый текст Привет всем. Я новичо…

until I've installed the 24.05 image the cubieboard2 came up with an HDMI output on video, I have an DVI to VGA Adapter connected and could use an USB Keyboard+Mouse and the VGA Monitor. Since I've installed the Armbian_community_24.5.0-trunk.667_Cubieboard2_jammy_current_6.6.31_xfce_desktop.img.xz on the SD card, the system comes up with an ASCII Console on the VGA Monitor, later the screen gets cleared with only an cursor in the left top and then gets switched off. I've managed before to switch the output of the X-Server from None-1 to HDMI-1-1 using xrandr, but this is only possible with an proper and authenticated Display and I have to use an autolog…

I have an Orange Pi Plus 2 that has worked with Android installed for a long time. But now I needed to install Linux on it. I needed to find a Linux image to install on it, and I've already got several, but all the ones that worked, and that were on the login screen, didn't go beyond that, since in none of the 4 USB ports the keyboard worked and I imagine the mouse. I read somewhere that the image Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z or Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112_desktop.7z, but I don't know where to get it, hoping to solve all the problems. Can someone give a helping hand, please?

Hello, I used the Wheesy version for my web server with virtual host that worked. The site is in / var / www / bbp / public_html / Now , I use the Jessy version with the same structure , Apache does appear to me that the page "default". I have no error when validating the virtualhost , I raise apache well and nothing is displayed for the site " bbp / public_html / " I do not understand what can no longer function . Thanks François

Using this file or upgrading from an older version results in no sda showing up. Please Help! http://mirror.igorpecovnik.com/Armbian_5.00_Bananapi_Debian_jessie_4.4.1.zip Please ask for further information as I am still learning a lot. Thanks Igor, great work on the distros. Gary

Hello, I am really struggling trying to find up to date images (debian jessy) for my Cubieboard4 A80. I'm thinking of selling the hardware now as i'm stuck on the old images which are not being patched: http://dl.cubieboard.org/model/cc-a80/Image/debian-server/ Can you suggest how i should proceed? Any help would be greatly appreciated Thanks, phrag

I just want to post a thank you to the developers and contributors who have built one NICE distribution. Over a year ago I bought a few OPi PC as a possible replacement for Raspberry Pi based HAM radio projects I support. To say I was disappointed in the distribution from the manufacturer is a understatement. Without Loboris stepping up and getting something usable I would have tossed them in the trash and moved on. Last night I downloaded and installed Jessie server from Armbian. What a pleasure. Small, clean and a giant plus for me, HEADERS!!!!. I am so tired of having to build the headers for a kernel so I can compile the out of tree modules I need. I just ordered a f…

Hello, I am using Armbian nightly legacy Jessie 3.4.113 build and it seems Mali drivers are included. Please, How should I set values in boot.cmd and boot.scr to mali HW acceleration work properly? I checked this site http://linux-sunxi.org/KernelArgumentsand tried to place something like "sunxi_ve_mem_reserve=64 cma=96 sunxi_g2d_mem_reserve=64 sunxi_fb_mem_reserve=32" to this file on setenv line but armbian fails to boot. I would like to use HW acceleration in VLC. Thank you.

I have an ADC and DAC board built for Raspberry Pi which has 2 slaves on the SPI bus, requiring ce0 and ce1. This works fine on the Raspberry pi 3, which installs devices /dev/spidev0.0 and also /dev/spidev/0.1, to access each slave. On the OPi PC I can access slave 0, but not slave 1. In /dev on the Opi there is only a single spidev device: /dev/spidev0.0 and no spidev0.1 device. I have modified the script.bin (I am using Armbian legacy OS - Armbian_5.14_Orangepipc_Debian_jessie_3.4.112_desktop) by editing the .fex (and making a new script.bin) to add a spi_cs1 = port:PC07<3><default><default><default> line. But adding this prevents any spide…

Hi there, I recently purchased a NanoPi NEO Air from FriendlyElec with a CAM500B module. It works alright with the mjpg-streamer and their provided Ubuntu Core. I built an Arabian 5.27 Nano Pi Air Debian Jessie image with the default kernel and the device is no longer found. I've forced the load of ov5640 and vfe_v4l2 in /etc/modules, but /dev/video0 isn't appearing. The kernel log has this in it when the module is loaded: [ 116.519650] [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11 If I boot back to Ubuntu Core via SD, the camera is back.

Ping too high(OrangePi Zero) Armbian_5.25 What could be the problem?

Whats the suitable image for Orange Pi PC H3 Quad-core ( https://www.banggood.com/Orange-Pi-PC-H3-Quad-core-Learning-Development-Board-p-1010455.html )? Thank you!

Recently i have been experimenting with interrupts on orange pi zero plus2-H3 trying to capture data-ready pulses from an external adc on gpio PA19. The aim is to synchronize spi-read-data transactions with the incoming adc data-ready signal. First I tried to get it to work on legacy kernel 3.4 by adding the following section in to /boot/script.fex and compile the .fex file to .bin file using fex2bin: [gpio_para] gpio_used = 1 gpio_num = 6 .... gpio_pin_6 = port:PA19<0><default><default><1> This configured the pin properly as i had tested on other pins with some leds and it works. The driver code for capturing the interrupt was based o…

Hello. I have a problem with SPI interface I already tried to compile SPI interface as module in kernel config and then to turn it on, but what I get is: root@bananapi:~# modprobe -v spidev insmod /lib/modules/4.13.4-sunxi/kernel/drivers/spi/spidev.ko root@bananapi:~# lsmod | grep spidev spidev 16384 0 root@bananapi:~# dmesg | grep spidev *nothing* root@bananapi:~# ls /sys/class/spi_master/ spi32766 I found a topic about enabling SPI on Banana Pi Pro here. But after repeating same steps(I mean decompiling dtb, adding spidev and compiling it back) for Banana Pi M1 it doesn't boot any more. After U-boot the cursor blinks for about 10 seconds a…

Hello, sorry but my english is not best. I tried to search forum for these problems, but I do not found the answers First problem is that serial console do not work for me, just random symbols, I already tried 3 USB to RS converters with 3.3 V logic, hercules_3-2-8 and putty as SW, with multiple setting, mostly 115200, 8 data bits, no handshake, no parity. Second problem the HDMI do not show useful data either, at least for me there was nothing I can understand as problem. I have 2 orange Pi lite available, so it is probably not a board problem, I tried 2 SD cards and multiple images (desktop legacy kernel 3.4.y and mainline kernel 4.14.y …

I can boot fine with console connected. when I disconnected console ,boot will not finish. then I connect console ,terminal will show > > how could I boot without console connected?? thanks help~~ ------------------ ARMBIAN 5.50 user-built Ubuntu 16.04.4 LTS 3.4.113-sun8i

I installed Armbian_5.59_Bananapipro_Ubuntu_bionic_next_4.14.65 onto my Banana Pi Pro. However, there is Internet for now. $ip address gives me the following messages: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000 link/ether 02:86:02:42:2f:4e brd ff:ff:ff:ff:ff:ff 3. wlan0: <NO…

I have an Orange Pi Plus 2E I'm using as a cheap desktop computer/kiosk. I want to run Armbian on eMMC but use an SD card for file storage. If I boot off the eMMC, then insert an SD card (formatted as ext4) after boot, the system works well. But if I boot off the eMMC with the SD storage card in the card slot at boot, the CPU load increases and performance lags. Here's the output of armbianmonitor without an SD card, with two Firefox windows and a terminal window open while streaming audio using Audacious: Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 06:18:26: 1296MHz 1.10 25% 3% 21% 0% 0% 0% 54.1°C 0/9 06:1…

Good afternoon, please help configure the rotation of the logs. I am completely new to this system, unfortunately, I can not find a normal instruction on how to configure rotatilog. My problem is that the logs are full, and my necessary scripts stop working. If I constantly clear the logs manually, then the scripts work fine. I tried to configure the rotation in accordance with the instructions, it only works before the reboot, after the reboot, everything I fixed with the rotation changes the paths to /var/log.hdd/. Please help me make sure that all logs do not exceed 1m. and constantly spinning. I apologize in advance if not fully expressed his thought.

Hi all. I understand, maybe my board Nanopi Neo CORE is not supported on the forum, but maybe someone will tell me how to write dts correctly # uname -a Linux NanoPi-NEO-Core 4.14.111 #126 SMP Mon Feb 22 17:04:18 CST 2021 armv7l armv7l armv7l GNU/Linux I compiled and installed ffmpeg with Cedrus H264 and cedar_ve.ko After that I see # dmesg | grep cedar [ 4.982170] cedar_ve: loading out-of-tree module taints kernel. [ 4.988972] sunxi cedar version 0.1 I'm trying to edit and compile /boot/sun8i-h3-nanopi-neo-core.dts using sun8i-h3-nanopi-neo-air.dts First I change before soc reserved-memory { …

Hi, i could control the OTG micro USB port power on my NanoPi Neo (H3) by exporting and writing to GPIO 354 (line 2 of GPIO chip with base 352) I'm using Kernel V6.6.62 and I created a tiny device tree overlay defining. Excerpt below: usb@1c19000 { dr_mode = "host" } usb0-vbus { status = "okay" } This works fine! For test purposes, I switched to a NanoPi Neo2 (H5) with Kernel 6.6.62 (64 bit). Here, the OTG port is powered on and is usable by default without any overlay. But the on/off control does not work anymore. All attempts to export GPIO 354 give "write error: Device or resource busy". Schematics show no circ…

As soon as I installed the latest version of the Wheezy I have found that there is some problem with an USB. When I start my Orange PI I can see that USB devices are power supplied from the bus only first a few seconds (when the bootloader is active I guess) and then being switched off. When I plug an USB device and supply it externally then it seems to be working well. My question is: how to switch on power supply of the USB port on my Orange PI? I have read a number of linux forums and found nothing. Very promising seems a command echo on > /sys/bus/usb/devices/usb1/power/level or similar but unfortunately it has no effect. Any hint, guys? Thanks a lot. Radek

Hello, I have a OrangePi Plus 2. I want to build images of desktop and no desktop. I build Debian and works fine. But for desktop only debian works not ubuntu xenial. It not boot. Also in Desbian when I can add external Button to can start pc with it ? like a real computer ? Tat's normal when i connect to DC it take a time to start ? Thanks

Hi. i tried to use g_ether module on legacy 3.4.112 kernel but without success. Could anyone help me? this is what i have when i run modprobe g_ether: [sw_udc]: [sw_usb_udc]: binding gadget driver 'g_ether' [sw_udc]: alloc request: ep(0xc0a8b7e8, ep0, 64), req(0xef3c8940) WRN:L2728(drivers/usb/sunxi_usb/udc/sw_udc.c):ERR: usb device is not active <4>g_ether gadget: using random self ethernet address <4>g_ether gadget: using random host ethernet address <6>usb0: MAC 5a:1d:b8:22:02:7f <6>usb0: HOST MAC 6e:49:95:27:67:f7 ep_matches, wrn: endpoint already claimed, ep(0xc0a8b834, 0xeeb62480, ep1-bulk) ep_matches, wrn: endpoint already cl…

Hi everybody, I need some help because I can't make my OPIPlus2e working the way I want. If I understood well I have to install latest armbian, and copy/past script.bin, but sometimes ethernet is not recognized. I tried every distros on my orangepi2e, but I can't install things like kodi (refuses to start, missing libs), or making work hfs drive (can't mount hfs although hfsprogs well installed). I ended up installing openelec and it works great, but I would like to do a NAS with it. Is it still in active development or there is working ISO ? Thank you very much. Best regards, Poukin

Hi, I'm getting going with a pile of Nanopi Neo's and am using the jessie server image with the legacy kernel I'm having trouble with the repositories - I see this error when using apt-get ... W: Failed to fetch http://apt.armbian.com/dists/jessie/InRelease Unable to find expected entry 'jessie-utils/binary-armhf/Packages' in Release file (Wrong sources.list entry or malformed file) I saw the discussion in http://forum.armbian.com/index.php/topic/1834-repository-management/which says the problem has been fixed ... but, er, it does not seem to be. Any ideas welcome on how to sort this out. Thanks Jason

Anyway, so here is another i can't log in my Orange Pi Zero, tried both images with Etcher, So where am i? It's a bit weird, i try various USB wall chargers and sd cards, but it always get to the same point: Permission denied, please try again. root@192.168.1.19's password: So let me ask you guys something, am i doing something Stupid, if i plug this into my modem, i can ssh to it yeah? there nothing i need to do? So i Nmaped it and sore that the vnc port is open, so password for that is 1234 as well? Like i went through the source, and i can see that the password is 1234, so the only thing that i can put it to is the setup of the sdcard but Etcher verifies th…

Hi, I am trying to make the OPI Zero boot with the help of the onboard SPI with the goal to boot from an usb drive and not from the sdcard. What steps should be executed. I only managed to get the Xenial image to work with my 512Mb board... so that is what I want to use. I assume... I need to make u-boot work with the sdcard... move the whole thing to the usb drive (with the u-boot) and than populate somehow the SPI with the image of an SPL, which would get it up through the u-boot on the usb. So I would need some in depth guidance (best would be some example commands to be used), what steps and tools should be executed to make it work. Thanks in advance &amp…

Hello all, I'm working on a project where I need at least 460800 baud on a UART on the NanoPi Neo Air. Works great at lower baud rates but can't seem to get it much faster than 115200. Any thoughts on clock adjustment or CPU speed? I'm using Armbian 5.24 with the 3.X kernel

Hello! Has anyone succeeded in using the OPi Zero's Expansion Board audio output jack? I can't seem to get any sound out of it. Any help with the configuration would be appreciated. Thanks

Hi, I'm a noob with this mini Pc's, but I think that I don't have doing anything wrong. My Orange Pi Zero no boot, no led power, only leds of ethernet, but the power leds (green and red) don't work, I tried with 2 microsd, and 2 systems too, but same problem, no reaction. Any solution please? Thanks.

I was hoping I could find some information as to why linux-jessie-root-next-bananapipro was being held on my BPi Pro system. The kernel and u-boot packages have been upgraded. I've held back on updating linux-jessie-root-next-bananapipro because I'm concerned it would break something. Is there some log file I should look at or some documentation somewhere?

Hello so i got Orange Pi PC 2 today and installed armbian from here : https://www.armbian.com/orange-pi-pc2/ i can SSH to it. but i dont know how to get AV out to work :/ can u help me ? im a total Beginner i just need to get Tv out to work and start learning. I know that armbian for H5 is in the early development state.

I'm testing the nightly image: Armbian_5.32.170704_Nanopineo2_Ubuntu_xenial_dev_4.11.8.img I've got it running nice and stable as a router and wifi AP, with 2 USB ports, one wifi adapter on each port. But when it's been off for a while and I power it on, it doesn't boot on the first powerup, only if I disconnect power and then wait a few seconds then power again. I've tried 2 different 2A 5v power supplies, one that I've successfully powered RbPi 2s and other Linux SBC's for months at a time, no problems. The voltage is good. I also tried a beast 10 port USB charger that has 6x 2A ports. Same behavior for all power supplies I've tried, and I…

So I have an OPI0 perfectly running then suddenly it freezes. All I can find on /var/log/syslog Jul 1 10:35:10 localhost CRON[1553]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Jul 1 10:36:08 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:36:38 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:37:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:37:37 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:38:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:38:37 2018 [v8.16.0 try http://www.rsyslog.com/e/200…

I've got a LeMaker Banana Pi Pro board, with LeMaker Banana Pi Pro Camera V1.0 which is a ov5640 module. I think there are some on-line manuals from official LeMaker, for instance: http://wiki.lemaker.org/BananaPro/Pi:Camera_Module . However, it seems Armbian_5.59_Bananapipro_Ubuntu_bionic_next_4.14.65 hasn't provided such a ov5640 driver module for me to load? Where can I find the ov5640 driver module ? Cheers Pei

Is it possible to install a desktop Enviroment on the Orange Pi One Plus without any problems? Whenever I use the Armbian config minimal desktop option, the Orange Pi stays on a red LED. It says it cannot install simpleFB, and it just sits at the starting kernel screen.

Try to use a DTS file to add bluetooth reset gpio control to rfkill, but `rfkill list` doesn't show "sunxi-bt". /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&pio>; __overlay__ { bt_pwr_pin: bt_pwr_pin@0 { pins = "PG13"; function = "gpio_out"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { rfkill_bt { compatible = "rfkill-gpio"; pinctrl-names = "default"; pinctrl-0 = <&bt_pwr_pin>; reset-gpios = <&pio 6 13 1&g…

I want to downgrade the kernel because auf random freezes on my Banana Pi and was following this tutorial to downgrade to Mainline stable kernel (Armbian 5.31): At apt.armbian.com I can find all required packages except for: linux-firmware-image-next-sunxi According to the linked thread I need this package otherwise the system may not start anymore. Could someone tell me where to find that package? Thanks :-)

A couple of years ago wifi worked without any problems on old version of Armbian, but on the current version It doen't work completely. Any suggestions? uname -a Linux HAMServer 5.4.45-sunxi #20.05.4 SMP Sun Jun 14 21:46:20 CEST 2020 armv7l armv7l armv7l GNU/Linux lsmod | grep 8189fs 8189fs 1069056 0 cfg80211 413696 1 8189fs ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.88.16 netmask 255.255.255.0 broadcast 192.168.88.255 inet6 fe80::8385:e766:9c48:e593 prefixlen 64 scopeid 0x20<link> ether 02:81:a4:6e:47:9e txqueuelen …

Hi I am trying to set up auto-login with enable desktop, using armbian-config as user root, and getting 'killed' once I select which under-priviledged user to enable. (There's two to choose from, and both behave the same with the same error reult). I couldn't find a known issue, please help! OPi Zero LTS 512MB / Armbian from armbian.com Sam

Hi there. I use Orange Pi zero as home print server. It works for few months for now and I am very pleased with that. Although, my printer falls into deep sleep after printing (it's Brother HL-1110EW) and cannot be woken up by the server. I have to start printer manually to print next printouts. Thus I wanted to install tea4cups to drive a relay turning the printer on and off when needed. I installed the WiringOP-zero (from here: https://github.com/xpertsavenue/WiringOP-Zero) but then strange things become to happen. I connected temporarily a LED diode to indicate the changes of the GPIO. (GPIO-7 and GND). The LED is on all the time, no matter what command I se…

Good morning, I am designing a board to use a NanoPi Neo Core. By default it comes without Wifi or BlueTooth. I had thought about putting the AP6212 chip on it. Can someone tell me if it is compatible with Armbian in its latest versions? Thank you and best regards!