Allwinner sunxi

Hi, sorry, I searched the forum but couldn't get any definitve answer to my questeion.... Is Video Decoding Hardware acceleration, CEC control and HDMI Audio Pass Through working on the OrangePiZero3 device? Thanks to its gigabit ethernet it would be the perfect replacement for my cheap amlogic Box which does only 4K25P due to hardware limitations..... Thanks for your input regarding this topic! Cheers Ford

I want to make panfrost work on H6 platform, I use linux 5.6.16 latest mesa Xorg 1.20 I install and run them. But they dispaly : DRM_IOCTL_PANFROST_MMAP_BO failed: No such file or directory What should I do?

Hello, I am using a orangepi one plus, but that might be no connection with my issue. I am having the following network configuration: # Network is managed by Network manager auto lo iface lo inet loopback allow-hotplug eth0 eth0.1 eth0.10 auto eth0 iface eth0 inet manual pre-up ifconfig $IFACE up post-down ifconfig $IFACE down auto eth0.1 iface eth0.1 inet static address 192.168.1.250 netmask 255.255.255.0 gateway 192.168.1.1 auto eth0.10 iface eth0.10 inet static address 192.168.10.1 netmask 255.255.255.0 if i disconnect the network cable and connect back the interface is not come up automatically from the state it…

Hi there, I do no need help how to sort it out. This is only report for Igor. I installed Jessie server image with legacy kernel on my Cubietruck few on April. I decided try upgrade to vanilla kernel about two weeks ago with command see below. And today I decided return back to legacy kernel with same command. (it is not important why but I have answer for it, I am enjoying testing ... ;-) ) ... but before I rebooted my experiencies say check /boot folder and I did not find important files there. I used command: wget -q -O - http://upgrade.armbian.com| bash And here is output of log: cat /boot/upgrade.log No packages will be installed, upgraded, …

Today I did update my 3 NanoPi Neo2 via apt update/upgrade, but only one is accessable via ssh after the update. (without SSH/SSL-conect also no conection via SFTP/WinSCP because if the timeout) The one which is accessable has after the update Welcome to Armbian 23.02.2 Bullseye with bleeding edge Linux 6.7.12-edge-sunxi64 ( Machine model: FriendlyARM NanoPi NEO 2) The two other do show prompts for user/password but doesnt login via ssh - and after some time they time out and I can reenter user/password After connecting via TTL-serial I can also enter user/password and then the Neo2 shows me: _ _ ____ _ _ _ …

Hi, Using the latest Armbian release (19.11.3) on OPi Zero (512MB, board revision 1.5) I have a strange issue. On kernel 5.3.x, Ethernet connectivity drops sporadically, around once every couple of minutes, for typically 10 seconds or so and then recovers. When the drop happens, a ping from another machine on the network produces 'no route to host' - then after around 10 seconds or so the network comes back up. The OPi Zero continues running normally during the 'outage', without functional network access. There is nothing in the dmesg log when this happens. Switching to kernel 4.19.62 from armbian-config, everything works perfectly. Back to 5.3.x, the iss…

In my /boot/config for 3.4.112 I have CONFIG_SUNXI_PWM=y yet there is no /sys/class/pwm-sunxi directory. Do I need to do anythig special to control onboard PWM? This is stock Armbian 5.16 with legacy kernel.

Hello. I just wanted to let you know about a possible bug I have found in the kernel installation script. I was using my OPi+2e with the default kernel, and today I installed next to test it, using armbian-config. Everything went fine, and seemed very stable overall (I didn'd use it for more than two or three hours, though). But then I wanted to revert to default, so I used armbian-config again. When I rebooted, the board started the u-boot sequence, but it got stuck on "Starting kernel". No other messages after that. I tried several times, with the same results. Since I have no logs, the only info I can give you is that I have an external USB HDD …

I have ironed out my OPZ woes and have it working well now along with the Mainline Armbian image. As we may know the onboard wifi is garbage and will not get fixed, however I found a dirt cheap plug and play usb alternative on ebay (or aliexpress.com) using the common (Ralink?) mt7601u kernel driver. As long the dongle matches the photo in the listing it should have the same chipset. It has very low power consumption and at least with my wifi router gets the maximum 10mbit/sec throughput for downloads on my internet connection at a distance of 5 meters. I also added to /etc/modprobe.d/blacklist.conf .... blacklist xradio_wlan …

Im using Orange Pi PC+ with Debian 12 minimal image. I tryed to install/compile ovpn-dco-v2 as of standard deb (openvpn-dco-dkms) as well as of git (https://github.com/OpenVPN/ovpn-dco). In bouth cases compilation prcess itself was finished successfully but resulting driver ovpn-dco-v2.ko didn't work. In the first case, the driver caused a kernel error. In the second case, after "modprobe ovpn-dco-v2" , openvpn stuck somewhere in the middle and lsmod has hung down, blocking the console. Before installing the driver package i did: apt install build-essential kmod debhelper devscripts linux-headers-current-sunxi And as i thought everything went fine. …

I am building armbian with mainline kernel (4.14.19) on jessie for OrangePi Lite... Sometimes on booting my Pi Lite, the wifi does not work. I cannot create hotspot and connecting to existing networks will not work. A short time after booting I see the following messages in the dmesg log [ 102.077151] sunxi-mmc 1c10000.mmc: send stop command failed [ 102.077184] sunxi-mmc 1c10000.mmc: data error, sending stop command If I remove and reload the 8189fs module I will see the following error in the dmesg log [ 572.371452] rtl8189fs: probe of mmc1:0001:1 failed with error -110 If I don't see the mmc errors after startup (say 5 minutes) the w…

Hello, I'm using a BananaPi and just tried the latest version (10.6.2015, Linux 4.0.5) of your great distribution. Unfortunately, support for ath9k_htc based USB Wifi adapters seems to be missing, which is crucial for me. (ath9k_htc works great using free and open source firmware.) Could you please add support for this kind of hardware for future releases or give me a hint how I could add support to your existing images? Thank you and kind regards, LINMOB

Hi, I get this line on my welcome screen of my Orange Pi Zero: Welcome to ARMBIAN 5.38 stable Ubuntu 16.04.4 LTS 3.4.113-sun8i When I checked the download page, I see this as the file name: Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14 I got confused about the numbers 3.4.113 and 4.14.14 What do they mean? Is my installation behind the latest version? Can I upgrade to it?

Quick debugging info, subject says all. Other apps like cap.c or motion or motioneye works perfect and capture and streams live video. Working onliner: ffmpeg -f v4l2 -channel 0 -video_size 640x480 -i /dev/video0 -pix_fmt nv12 -vcodec h264 -preset fast -b:v 2000k -qp 20 ffmpegtest.mkv Working distro Armbian 5.30 root@nanopiair:~# cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=nanopiair BOARD_NAME="NanoPi Air" VERSION=5.30 LINUXFAMILY=sun8i BRANCH=default ARCH=arm IMAGE_TYPE=stable root@nanopiair:~# modinfo vfe_v4l2 filename: /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/sunxi-vfe/vfe_v4l2.ko description: Video fro…

I've seen on webpage that there is a new kernel 3.4.109. I'm currently using 3.4.108 and apt-get update/upgrade delivered new root and also new uboot, but noit new kernel ... is this known or "as planned"?

Hi, I have a problem with an update notification that seems to be permanent. The following lines always appear when I log onto my system: Welcome to ARMBIAN 5.36 user-built Debian GNU/Linux 8 (jessie) 4.13.16-sunxi System load: 0.71 0.63 0.62 Up time: 1 day Local users: 2 Memory usage: 29 % of 995MB IP: 192.168.2.103 CPU temp: 42°C Usage of /: 60% of 15G [ 0 security updates available, 2 updates total: apt upgrade ] Last check: 2017-11-26 00:0012 After sudo apt-get update and upgrade the lines telling me that 2 updates are available are still …

Hi Everyone. I have an Orange Pi One and I can use the micro USB (otg) port as a standard USB port - I can plug in a memory stick or USB speakers and it works fine. Is it possible to have the same functioniality with the OPI Zero? I tried and it does not work - I am powering the board through the GPIO header. Even if I plug in USB speakers that have an LED indication - no LED lights, so I guess no power. I looked at the fex file from the OPI One and could not see the difference there in the OPI Zero. I know it is in beta, so I do not expect it straight away, but it would be good to know if it is possible Thanks for any help. J

hi all, I use cubietruck Linux 3.4.104-sunxi I would like to understand partition ramlog-tmpfs on /var/log type tmpfs (rw,relatime,size=524288k) in fstab is not present. I have the problem that it is always full, more than 90% My cubietruck it is install on nand, I would like to mount the partition of sd, how can I do? regards

Hi, I've managed to install Armbian_20.05.2_Orangepiplus2e_focal_current_5.4.43_desktop on my board. Now I'd like to get decent web-browsing performance (i.e. 1080 videos on a browser) and I've tried installing the mali drivers with no luck. Is there an updated guide that works with the latest version of armbian? Thanks in advance

Hi, my old 1366x768 VGA LCD monitor was working with legacy kernel but after I downloaded and installed image with new kernel ( Ubuntu_xenial_next.7z) I could not get it to work with VGA output. When I set armbianEnv.txt with below, it still outputs to HDMI disp_mode=1366x768p60 video_mode=sunxi:1366x768-24@60,monitor=vga,hdp=0,edid=1 then I tried to add this with no luck. Both monitors go blank with it. extraagrs=disp.screen0_output_type=4 Is VGA supported with new kernel? If so, how ?

Hi first of all sorry for my bad English .I have an OPI PC + ,I install Ubuntu on my sd card and after boot i used nand-sata-install command to use may nand but when i tryied to use my sd card (after format sd card) it did't work and after reboot i receive "panic= boot argument" how can i use my sd card and mount it when my dist installed on nand? even i checked this link for Cubietruck but it wasn't useful for OPI , and then i checked this and it was really hopeful but I don't now how can i exactly implement this .Actually I need to auto mount my sd card as a result when I reboot my OPI PC + I need my OPI boot from emmc instead of sd card. thank you for you…

I have read other thread regarding v4l2loopback kernel module installation. I got same problem like this message below ========================================= ------------------------------ Deleting module version: 0.10.0 completely from the DKMS tree. ------------------------------ Done. Unpacking v4l2loopback-dkms (0.10.0-1) over (0.10.0-1) ... Setting up v4l2loopback-dkms (0.10.0-1) ... Loading new v4l2loopback-0.10.0 DKMS files... dpkg: warning: version '3.4.113-sun8i 4.19.25' has bad syntax: invalid character in revision number Building for 4.19.20-sunxi64 Module build for kernel 4.19.20-sunxi64 was skipped since the kernel…

Hi, we have problems with 5 inch display from waveshare. Can somebody help us.

Hello, I am using Orange Pi PC Plus with Armbian Nightly. Since upgrade to kernel 4.11.0 audio stopped working, on kernel 4.10.11 everything was alright. When I am trying to open alsamixer i get error cannot open mixer: No such file or directory Can I fix it somehow? Can I still get last image with 4.10.11? Unfortunately it's not available at download page (too late).

Hi everyone!! Any chance to know the estimated schedule for having Gb ethernet working in mainline kernel 4.x for this board? Greetings!!

On my banana I get the following error: sudo apt-get install openjdk-8-jre-headless Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: openjdk-8-jre-headless : Breaks: ca-certificates-java (< 20160321~) but 20140324 is to be installed E: Unable to correct …

Hello, I have installed the latest version of armbian on my Orange pi win and I have not been able to make the desktop appear, it always stays waiting for a command, I have done update and upgrade and nothing. Can somebody help me

Hello! For the Cubieboard 2 on the SD card I use the image Armbian_5.25_Cubieboard2_Debian_jessie_default_3.4.113.img. It is only loaded with U-boot v2015.10.rar. But this U-boot v2015.10 480 MHz DRAM. At this frequency, my Cubieboard 2 freezes. Can anyone build U-boot v2015.10 to 432 MHz DRAM? I will be very grateful. I'm not very good at Linux. I apologize for the bad english.

I'm trying to get TFTP support into U-Boot but it insists that 'no ethernet found'. I've added a couple of nodes to the device tree such that it has 'status = "okay" and mac-address = [00 00 00 00 00 00]; I've also added a top level alias in sun50i-h5-nanopi-k1-plus.dts (as added by @martinayotte following this thread) as below. Not sure if the U-Boot config needs changing in any way but the network components are certainly being built. Any thoughts most welcome. AATIA. aliases { serial0 = &uart0; ethernet0 = &emac; }; U-Boot dump of the loaded DTB on running system follows: => bdinfo arch_number = 0x…

I downloaded the armbian focal image for NanoPi NEO/Core board, and it works great. (Specifically, Armbian_20.11.10_Nanopineo_focal_current_5.10.4.img, so it's a few months old.) I'd like to start creating my own image, and I'm all setup to do that, but what I'd love to do is start from the .config file(s) used to create the image I'm using. That way I have a known base configuration from which to start modding. Are those available anywhere to download? Thanks!

I'm using an Orange pi zero H2 and currently have the pi configured as an access point. I want to be able to SSH into pi using access point wifi, then switch pi onto my home wifi network. When I use the "nmtui" utility I no longer see any available wifi networks. Is it possible to see available wifi networks when I am using the pi as an access point? Thanks, orangepi noob

Hello, I’ve just tried to boot the theoretically universal Armbian_5.72.1_Olinuxino-a20_Debian_stretch_next_4.19.17 image (taken from ftp://staging.olimex.com/Allwinner_Images/A20-OLinuXino/1.latest_mainline_images/stretch/images/) on my A20-SOM device, but with no success. The following output is displayed: **File not found /boot/dtb/ ** libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via “fdt addr ” command. Aborting! ** File not found /boot/dtb/overlay/sun7i-a20-fixup.scr ** … ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree SCRIPT FAILED: …

I want to use an ADAU1979 with an olimex A20-Micro. Needs to show up as a device in ALSA, alongside the in- built CODEC - As far as I can see, this driver is in mainline kernel but I have no idea how to configure the kernel build to include it. Obviously we need to tell the system where its i2s/SPI interface is connected etc. Unsure which kernel version (legacy or mainline) to begin with. We do need a desktop environment and the olimex 10"/7" LCD to work also... I am starting this from a position not having built a kernel or kernel modules before so If this idea is a non-starter, someone please tell me so. Thanks.

Hello, i recently installed armbian on my newly bought Lamobo R1. Everything is working fine so far but for the onboard ethernet LEDs, they're not working as expected. The green LED on port 3 of the internal switch (also known as wan port) ist constantly on, no matter if there is a cable plugged in or not. The orange LED is always off. After some trial and error if figured out that on the other 4 ports the green LED, for the specific port, shows the current network traffic (is blinking) if the established connection is 10Base-T. If the connection is 1000Base-T, the orange LED shows the current network traffic and if the connection is 100Base-T no led is on or sh…

Hello, I recently installed Armbian 5.85 legacy on my new Orange Pi Lite in order to try out my new Orange Pi camera, but it's not being recognized at all, even after following the instructions in this topic: I already tried doing the following (as root) unsuccessfully (no errors returned, but still can't detect camera): sunxi-pio -m "PG11<1><0><1><1>" #DOVDD sunxi-pio -m "PE15<1><0><1><0>" #Power_Down sunxi-pio -m "PE14<1><0><1><1>" #reset modprobe gc2035 modprobe vfe_v4l2 Here's the output of lsusb: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001…

Is there a way to run netflix yet? Does Chromium run well and able to run netflix? Appears this doesn't matter, because Chromium doesn't work with netflix anymore... Does anyone know if chromium OS works well with OPi PC otherwise? Basically I want it to work for netflix, I also want to connect it to a printer, and the ability to run NordVPN and a torrent client would be a bonus as well.

I have BPI-M2+ shutdown -P now or poweroff does not power off the board Board is just halted and fan is still spinning Anyway to power off the board completely?

HI I noticed that the Windows 10 on Arm version has the ability to install on mini-pc, like the raspberry pi. My question is, is Windows 10 capable of being installed on the BOARD WITH h5 processor? I USE OF QEMU-KVM FOR INSTALL WINDOWS ON MY ORANGE PI BOARD BUT IT HAS VERY LOW PERFORMANCE AND QEMU ONLY USE OF ONE OF H5 CPU CORE . Is it possible to install on orange pi pc2 armbian and Windows operating systems at the same time with dual boot?

Hi everyone, i want to wake up orange pi on any gpio pin. Current i only can wake up from button on orange pi. There is a section of wakeup_src_para in fex configuration file, but when i append a wakeup_src with any gpio port, does not effect anything to wake up. how can i do?

Hi, i'm using Armbian on my Cubieboard 1, i've done the kernel upgrade with apt-get update && apt-get upgrade. I haven't understood how to make a full system update, including the security updates. Thanks and wonderful work!

Hello I have an allwinner H2 & H3 (PC +) when it does not boot on my LAN. If I want to try to use the LAN port. In / etc / network / interfaces the eth0 interface is not defined. I tried to change the iso but on Windows the iso is not valid. On Linux Linux the files are not -w and try to change but not possible !!! If I want to try to use the UART port and PuTTY it doesn't go with in the prompt. U-Boot 2020.04-armbian (Sep 02 2020 - 10:21:09 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC Plus DRAM: 1 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c1…

Hello, Just started on the latest Neo2 Ubuntu (Armbian_5.34.171121_Nanopineo2_Ubuntu_xenial_next_4.13.14) as we were tired trying to get around the challenges of the Ubuntu Core provided by FriendlyARM. Have enabled SPI we think (armbian-config->system/hardware/spi-spidev) and rebooted, but even after full power cycle we don't see anything in /dev/spi*. Is there anything special/additional we need to do to get SPI working (which we know does from our Ubuntu Core build). Thanks Rob

Hello everyone! I'm newbie with arm boards and i have Cubieboad A20(2012). I'm running on ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun7i and i have inssue than i can solve. tryin to load driver ath9k_htc for my usb dongle TLWN722N works with , but it don't do. Instructions to run script root@cubieboard2:/home/gui/Downloads/GitTPLINK/tlwn722n-linux-install# ./install.sh Installing firware... Changing to directory "compat-drivers-source"... Trying to select the ath9k_htc diver to be compiled... Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile…

I'm connected to my Orange PI Zero over serial. I have a WiFi connection configured in NetworkManager on the Zero to my home AP/gateway, and it can connect to the internet over it. However: the Zero does NOT reply to ARP requests. I have tried running wireshark on multiple other machines on the same LAN, both wired and wireless, i have run tcpdump on the router, and none of them have EVER seen an ARP reply coming from the Zero. Obviously this means that no machine on the network can discover the MAC address of the Zero, and cannot connect to it... unless... the Zero first connects out. once the Zero has sent a packet to a machine, the machine will …

Hi everyone, I installed the latest version of armbian available today for cubietruck. The volume coming out of the 3.5mm jack is really low. I checked on pulseaudio and the volume is set to maximum. I'm from another distro and didn't have this problem with audio before. Could someone help me? There are other people that have the same issue? Thanks in advance.

hi guys, using Armbian 23.02.2 Buster with Linux 5.15.93-sunxi on a NanoPi Neo Core LTS. I configured cron to do a daily reboot at 00:30. Every 10-20 days the system is becoming unresponsive unless I do a power cycle. Where should I begin to investigate this issue? Thank you

Hi when I use the orangepi PC plus TRRS audio output (analog), I have some glitches which are linked to the video mouvment. I've tested the connection between ground and video and it seems that on the left ground pin there is a natural link with video output (50 ohms), is this normal? my cable is a 4 pole TRRS. I even tested audio with cable directly plug on soldering but same result. How could I get a clean audio output? note that the hdmi audio output is clean. and my speaker system is clean if I plug it on a MP3 player with an audio jack. I use retrorangepi 4.2 which is based upon Armbian v5.54 (default legacy kernel)

Hi Yesterday after installing weewx I uninstall python 2 but well.... something went wrog because there was no welcome screen login with ssh. I've managed to install armbian-config and everything is right again except the release has changed from Orange Pi PC to xt-q8l-v10 Any hints to roll back to the former release ?? I've attached armbianmonitor url Thanks in advance

Hallo dear friend, I am a beginner . I bought a banana pi h3, I tried to turn it on, powering it to 5 volts, I connected mouse, keyboard, and monitor (with hdmi-vga adapter) but not signs of life, only the red LED is on , os image is loaded in sd card. I tried to press the on and reset buttons but nothing. I hope you can help me. Many thanks. Daniele.

Hi I'm auto-login using nodm with orange pi. I run my udp.py file by creating a file named udp.desktop under the .etc/xdg/autostart folder at startup. but I need to play the wav file using pygame in the .py file, but I get a warning that the audio device could not be initialized. If I trigger my .py file manually, I can play the wav file without any problems. probably unable to load sound drivers during autostart. Can you help with this.

I installed armbian latest release. When i shutdown system desktop closed. After 1-2 seconds, desktop opened again And after 1-2 seconds closed again. Why desktop is launched again after closed? Is it a problem? How can i fix that?

Hi, I have two questions: 1. Where can I download the latest image for my board? rom this forum entry I see there is no armbian image for the first Orange Pi? The link https://www.armbian.com/orange-pi/ doesn't work, as it redirects to https://www.armbian.com/orange-pi-plus/ which is definetly not the same (A20<>H3) 2. After doing a 'firmware upgrade' from armbian-config, it identifies itself as a Banana-pi. Is it normal? The MOTD is BPi and armbian-config shows BananaPi as well.

I have 1 "Customised Olimex Lime A20 SBC with RTL-SDR chip installed in the board (AirNav XRANGE). Currently the OS I'm using is the Lime A20 Armbian Stretch 4.14.84, everything is works fine except for the 2 GPIO LED. I have no idea how to let it work. I have the edited "sun7i-a20-olinuxino-lime.dtb" from Armbian Jessie 4.11.5 which is mainly for the board. May I know is there a way to incorporated the "Armbian Jessie 4.11.5's sun7i-a20-olinuxino-lime.dtb into the A20 Armbian Stretch 4.14.84 so that the 2 LEDs will work again? The edited dtc for LEDs to work "sun7i-a20-olinuxino-lime.dtb" attached. Hope to get so…

Ok, so, first of all, I am a complete noob. I bought Banana Pi thinking that it is similar to Raspberry Pi's architecture but it's obviously not. I bought a 240x240 Waveshare 1.3 inch hat and I was wondering how to get it working on my Banana Pi Zero (H2+). On Raspberry Pi I can use Juj's fbcp-ili9341 driver but it's probably not compatible with Armbian, right? How do I go about it? Also, it would be nice to know how to detect buttons (that are on the hat) and convert them to key strokes. Thanks!

Hello, I know one should't ask or complain here regarding the dev kernel branch, but maybe somebody of you stumbled upon this and knows where to point me: I successfully build and used the "dev" kernel several times for the BananaPi (Allwinner A20 Soc) and it works just fine. The patch regarding the axp209 sysfs interface can simply be taken over from the from the "next" kernel branch and you get a working temperture reading from the axp209 pmu. I still haven't managed to get the internal soc's temperature sensor working in dev kernel, though. I know it has something to do with the touchscreen driver but couldn't find out what exactly is required to make it…

I have been working with the legacy Ubuntu on this board with great success - and now on the latest nightly build of Ubuntu ARMBIAN 5.32.170921 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i All is well, thanks to this command added to /boot/armbianEnv.txt overlays=uart1 uart2 uart3 i2c0 i2c1 I can now see all the ports - and both I2c channels - the ONLY issue I have is that UART0 is occupied doing serial debug and for the life of me I cannot figure out how to turn this off. I do not need a serial debug port and would rather use this as a general purpose serial port. When I try however, debug info comes out.. Can someone tell me…

Hello, I have two questions about 'apt-get'. How come that the debian 4.0.5 image the apt command will not accept 'apt update' or 'apt upgrade'? Is this a typical debian thing? Also how do I please enable the colored progress bar for apt? Thx,user4747

First time poster, hopefully I'll get along with all of you! I am currently trying to connect a DS18(b)20 cable to my Banana Pi M2+, which is running Jessie Desktop. I connected the 3,3 V to Pin 1, GND to Pin 6 and Data to Pin 7, as well as the recommended 4,7k Ohm resistor between them. Since, as I should have mentioned, I am an absolute beginner (literally just got into this a few days ago), I used a German tutorial for this, which told me to enter the following into my command module: After which my /sys/bus folder shows a "w1" folder, which it does. However, the cable itself cannot be found. After some tinkering, I found that w1-therm does not seem…

Hi. I've installed Xenian Server on cubieboard1. Host connected to LAN/Internet. I can do apt-get update/install, but I cannot ping the host inside LAN (time out). May be the reason any fw rules on clean system?

Hi, I have an Opi+2 board and I want to overclock it. Assuming that I have a proper cooling, how can I do that? I want to overclock it to 1.6Ghz.

Hi All! Legacy kernel says: "Enabled audio devices: analog, 8 channel HDMI, spdif and I2S (if wired and enabled in HW configuration)" But there is no multi channel device listed in aplay -L , like surround51, surround71, etc. With "speaker-test -D default:sunxisndhdmi -c 6 -t wav", We got a downmixed stereo result. Receiver device is a BEM-182 Broadcast Monitor on its HDMI input - only 2 VU-meter band appears. Other test setup is the same receiver in SDI input mode with an HDMI to SDI converter. Specs of this adapter declares that it supports 8 channel, and this time 8 VU-meter band appears on the monitor so device is ready to receive multi-channel audio, but…

Hello, i am new here and need the line in from MCU audio codec(U1-3 Pin AB20 & AB21), located wired on CSI connector(CON1 Pin 1 & 2), active. Is it possible? Regards Mario

Hi all, i'm trying compile 3.4.*, i used normal way - i downloaded scripts to manage it, i'm successful with compilation but my issue is that i want to connect relay to banana pi J12 (DIP8) pin 5 which should be PH3 on A20 and that relay should be connected in parallel to switch button on PC ... so it means each switch (even fast) of the level can start turn off pc :-( so my issue is that uboot default configs for banana pi is having irrelevant configuration of pins that are prepared on connectors to be used as GPIO ... for example PH3 and PH5 at banana pi's J12 are not related to VBUS of USB as it's written in configs and fex, please somebody could tak…

Until the day Armbian can auto-configure HDMI output (with respect to a TV or DVI computer monitor), the thought occurred to me that the Beelink X2 defaults to Android KitKat 4.x, and from there maybe it's possible to plug in the TF card that you'll be rebooting into, then access the card from Android to makes changes, like: h3disp -m 720p60 -d If a DVI-monitor is expected to boot into. I was even brushing up on MIT App Inventor to make presets from Android side, but my skills drop off sharply at that point. The practical reason for his, is not only to show the neighbors but also have a media player anywhere there's a screen. In conclusion, I don't know what m…

Hi, At the beginning I would like to emphasize that I am not an expert in linux :) I use bananapi m2 + v1.1 in my project. Until now everything worked well with the SD card on armbian 5.25. My project is now finished and would like to run the system from emmc. I used armbian-config to move system from SD card to emmc. I chose the only option: Boot from eMMc – system on eMMC. Everything went well except the message (while formatting): EXT4-fs (mmcblk1p1): Unrecognized mount option "compress-force=zlib" or missing value mount: wrong fs type, bad option, bad superblock on /dev/mmcblk1p1, missing codepage or helper program, or other error In …

Hi, is there a problem in ARMBIAN Ubuntu 16.04.1 LTS 3.4.113-sun8i with the blacklisting? id like to use a rtl_sdr (rtf_433) device, after a reboot there is a problem with dvb_usb_rtl2832u-modul. i do it disloid with modprobe -r dvb_usb_rtl2832u before starting rtl_433, then it runs well i found the model blacklisted in etc/modprobe.d/rtl-sdr-blacklist.conf but it is loaded new after a reboot? sorry for my broken english ludwich ludwich@orangepizero:~$ lsmod Module Size Used by pcf8591 3363 0 bmp085 3487 0 dvb_usb_rtl2832u 351091 0 dvb_usb 15734 1 dvb_usb_rtl2832u dvb_core …

Hi, is it possible to install armbian on the emmc and a second armbian on the microsd card? So, if no microsd card insert the nanopi boot from emmc, otherwise boot from microsd?

Don't quite know what to expect here. The download page implies that there should be a gadget serial connection but there is nothing. I don't even see the USB DRC getting registered. Is this a known issue and is there a solution? TAIA. # nanopineo:~$ uname -a Linux nanopineo 4.11.3-sun8i #3 SMP Wed Jun 7 13:28:34 CEST 2017 armv7l armv7l armv7l GNU/Linux # nanopineo:~$ lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M # nanopineo:~$ lsmod Module Size Used by evdev 20480 1 brcmfmac 172032 0 brcmutil …

Hello, There are two physical USB port on the pi zero+ board : one is USB 2.0 host and the the second one is USB 2.0 OTG through a micro USB connector. As I power the card through the expansion pin I would like to turn the micro USB to a regular mode to connect a DVB dongle. With Armbian 5.38 and Kernel 4.14.14 (and also nightly build) I've done the following modification - in armbian-config enable usbhost0 - modify the /boot/dtb/allwiner/sun50i-h5-orangepi-zero-plus.dtb => decompile the file with dtc => edit the dts file and change the line dr_mode = "peripheral" to "host" => recompile the file and reb…

Hello! I found that on NanoPi K1 Plus there is issues with both of integrated audio adapter (H3 Audio Codec) and HDMI Audio (allwinner-hdmi 1c22800.i2s-i2s-hifi) 1. With H3 Audio Codec I getting only silence, altrought there is short click on starting and end of playback. "Stereo" mode was chosen in pavucontrol for this audio adapter. 2. With allwinner-hdmi audio playback is working, but left and right channels is swapped. Like above "Stereo" mode was chosen in pavucontrol for this audio adapter. Tests was performed from Mate desktop installed on top of Armbian 20.05.4 with Linux 5.4.45-sunxi64. "speaker-test -t wav -c 2" command was used for te…

hi there, i was setup linux-wheezy-root-cubietruck 4.2 on cubietruck nand.these days i upgrade system it show me a error message: Unpacking replacement linux-wheezy-root-cubietruck ... dpkg: error processing /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb (--install): unable to make backup link of `./boot/bin/lime.bin' before installing new version: Operation not permitted Errors were encountered while processing: /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb i thik this is a bug because dear developer don't think about when system install to nand later some problem. how to fix? thanks!! 估计用CT的很多是…

Hello, I bought Orange Pi Plus 2 and I have a banana router r1 on both devices I installed armbian it works good but I need just server + nginx + lua could you please help me, how to reduce the size of installed OS because 1.6Gb its too much Thank you

Hi. My board is Orangepi-PC Allwinner H3. I had wifi-dongle-usb problem.. so i used armbian.. I was download Image here http://www.armbian.com/orange-pi-one. I confirm wifi dongle is working! But Uart3 in not working.. I need uart3 for Bluetooth module.. I can't find ttyS3 in /dev/.. so i used source at https://github.com/igorpecovnik/lib I built two image.. -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0_desktop -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0 but both not working... I can see green led but i can't connect ssh... and cant' show console by monitor.. How can i do? Please help. Thanks.

It seems there are no any on-board wifi nodes (vcc33-wifi, vcc-wifi-io, wifi-pwrseq ) in sun50i-h618-orangepi-zero2w.dtb , and exists in Zero 3 dts . zero2w.dts: type_addr_wifi = <0x02>; zero3.dts: type_addr_wifi = <0x02>; zero3.dts: vcc33-wifi { zero3.dts: regulator-name = "vcc33-wifi"; zero3.dts: vcc-wifi-io { zero3.dts: regulator-name = "vcc-wifi-io"; zero3.dts: wifi-pwrseq { zero3.dts: reg_vcc33_wifi = "/vcc33-wifi"; zero3.dts: reg_vcc_wifi_io = "/vcc-wifi-io"; zero3.dts: wifi_pwrseq = "/wifi-pwrseq";

Device: Orange Pi +2e. Environment one 16GB SD Card and 16GB eMMC onboard. Output from Armbianmonitor attached. The eMMC device onboard is always detected as mmcblk2. Irrespective of whether SD Card is present or not or if you boot from SD Card or eMMC. This is observed only on 20.05 and 20.08 builds. It does not happen on 20.02 build. [ 3.769548] sun8i-h3-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pc not found, using dummy regulator [ 3.781702] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.784384] mmc0: new high speed SDHC card at address aaaa [ 3.785778] mmcblk0: m…

Hello, I'm using Armbian Xenial with ethernet on my local network. SSH and PostgreSQL seem to disconnect a lot. This is really frustrating with sshfs when I try to work with files on the Orange Pi Zero as a file server.. I tried setting a keepalive every second and that doesn't help either. I don't see anything in the logs that hints to anything. I have not attempted to use wifi. I did just notice the timezone was wrong, so I'll see tomorrow if that has something to do with it.

Hey guys, I have a OP3 H6 and I cannot seem to find out why the 4 x USB ports are not working only the single USB next to the HDMI works. Any Ideas? Cheers!

Hi, We are using an Orange PC Plus with Armbian Orange Buster OS. Connected to the 40-pin header is Pi-Supply LoRa Node pHAT. We are having trouble commumicating with the LoRa module. We occasionally can get partial messages. The OS reports no errors with the UART. Any suggestions? Thanks frank

After recent upgrade of Debian Buster stable on Orange Pi Zero Plus 2 leds entries disappeared from class directory: Could anybody provide some guidance on how to get them back?

Hello! I asked this question here: https://github.com/zador-blood-stained/fel-mass-storage/issues/1, but I decided to ask again. Is there a way to boot the current mainline u-boot via FEL? Is it easy to support this issue? I would be happy to receive any help. Thanks, Aleksandr

Good morning all. I was trying to power up my nanopi M1 through the VDD_5V and GND pins shown in GPIO.jpg image and/or the power pins on the debug GPIO pins, the schematics of the board power electronics are attached too on page 7 and 8, may by I'm wrong but what I see on those schematics is that all the power switchs and DC/DC converters can be powered through those pins but when I do that using a USB cable cutted on the micro USB side and prepared with the right terminals to fit the pins -with a 5V USB charger- then the tension drops aproximatelly to 4.60-4.67 DCV, the board starts by lighting dimly the power LED (as normally) but when the power LED lights strongly also…

Hi, I'm not seeing any audio device on my board. # aplay -l aplay: device_list:270: no soundcards found... Any solution? # uname -a Linux jacki-orangepi3 5.2.5-sunxi64 #5.92 SMP Fri Aug 2 07:51:38 CEST 2019 aarch64 GNU/Linux

Dear Armbian community, First of all, I am aware of the fact that what I am trying to achieve is not supported, but let me ask anyway. What I am trying to do is to build my custom root filesystem for my specific embedded needs (which is pretty minimal and without systemd) while still using kernel (5.8.16-sunxi) and modules provided by Armbian. It is going great so far, but the first issue I need to figure out is why there are approximately 60 second delays between each brcmf_fw_alloc_request calls (full dmesg available here): [ 40.602927] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 40.620798] brcmfmac mmc2:0…

Hi, I've been playing around with the latest build (Armbian_5.37_Orangepiwin_Debian_stretch_next_4.14.5.img.gz) just to see how things are going and I've noticed that the wifi has gone ? I saw that it doesnt talk about patching the ap6212 firmware anymore. Had a look around but couldnt see anything. I know it's a dev build but I hope that it's just a missing config file from that build branch or something. Thanks TB

Hi, I have trouble getting an IR receiver on the Orange Pi Zero+ to work. IR-Hardware: Orange Pi Zero Interface Board v 1.2 https://www.aliexpress.com/store/product/New-Orange-Pi-Zreo-Expansion-board-Interface-board-Development-board-beyond-Raspberry-Pi/1553371_32770665186.html I use Armbian 5.65 (Debian stretch), Kernel 4.14.78 I activate the IR receiver by adding "cir" to overlays in /boot/armbianEnv.txt On boot it is activated and the sunxi_cir module is loaded (and also lirc_dev, don't know why), see dmesg output: [ 5.245866] lirc_dev: IR Remote Control driver registered, major 244 [ 5.255140] IR LIRC bridge handler i…

Hello i found it on both my Opi PC+ and Opi Plus 2E , Both ARMBIAN 5.59.180918 nightly Debian GNU/Linux 9 (stretch) 4.14.70-sunxi. As i get some stability issues with Jeedom i'm playing with frequencies and governors and found that strange thing : root@orangepipcplus:~# cat /etc/default/cpufrequtils && cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true MIN_SPEED=408000 MAX_SPEED=1296000 GOVERNOR=ondemand 240000 480000 648000 816000 912000 960000 1008000 1104000 1200000 1296000 root@orangepipcplus:~# it seems there…

Hi, I have orangePI connected over HDMI to my TV but there is no video. If I connect orangepi with HDMI to DVI (to my monitor) the video is present. Can someone tell me what is wrong or how to set it up? The TV is Panasonic Viera (I have found similar question here: https://www.reddit.com/r/raspberry_pi/comments/5j89dk/having_trouble_with_hdmi_using_rasplex_and_a/) regards Peter

I'm using vanilla Ubuntu Xenial 16.04 from http://www.armbian.com/lamobo-r1/ When I follow the forum posts for copying everything to the SATA drive and updating /etc/fstab and /boot/boot.cmd the system boots as expected to the SATA drive. The problem I have is I get prompted to upgrade it on boot using apt-get upgrade. This also upgrades the kernel version from 4.6.2 to 4.6.3. Because I have moved the system from the SD card to the SATA drive the new kernel doesn't load, only the old kernel with missing modules which causes problems. When the kernel updates it updates the SATA drive /boot directory but the device uses the sd card /boot directory so things get screwed…

I have encoutered some difficulties on carrier detection with network-manager on ethernet port, on lime2, on default kernel, 5.38. On mii-tools and ethtools, carrier is correctly reported. The result, network-manager try to activate connection at boot even cable is not plugged. It's report drivers (sunxi_gmac) does not support carrier detection, as i found in syslog When unplugged, the connection is still active. Apr 11 11:39:03 localhost NetworkManager[491]: <info> [1523439543.5279] NetworkManager (version 1.2.6) is starting... Apr 11 11:39:03 localhost NetworkManager[491]: <info> [1523439543.5321] Read config: /…

Updated this afternoon and noticed my SATA drive isn't connecting. > dmesg | grep SATA [ 3.633118] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 32 [ 3.952927] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.781288] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102706] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102730] ata1: limiting SATA link speed to 1.5 Gbps [ 15.422687] ata1: SATA link down (SStatus 0 SControl 310) Let me know what I can do. Thanks!

hi guys i have little problem i connect my orange pi zero directly to relay but not work the realy is HUI KE hk19f-dc 5v-sh in yellow box , but if i attach 3v and gnd of gpio work o_O anyone can help me?? thankz

Hi all, i'm trying to install Digital Persona SDK on a olimex A20. Driver and lib's are ok. So far so good but after compiling en running the exe (i'm using Debian) i got the following error "symbol lookup error: /usr/lib/libdpD00701.so.2: undifined symbol: __aeabi_uidiv." this is a soft/hard float issue, is there a way to install a debian compatible with this lib? or how to work around? manufacture DigitalPersona (now Crossmatch) doesnt give any help and i dont have source code from this lib. any help would be welcome. thx Stefan

Hi, i recently switched from an old Cubietruck Image (1.XX) to the latest available. Everything works fine but i cant find the trigger disk-activity anymore. Is it an bug or an feature? P.S.: i downloaded legacy_jessie_4.5 best regards Martin

How can view kernel version?

I am looking for a working python "wiring library" for the NanoPi Air.... With pyGPIO i have limited success. Only GPIO4 seems to work. Just a quick "use this libray for python..." please. I need 3 GPIO pins (and UART1 which is working well under python...) Thank you!

· Hello, So I tried to figure out the original dtb file used but the system by default when I boot the image without any fine configuration. But I couldn't find any information about the default dtb. I checked at /boot/boot.cmd , but nothing is mentioned for "setenv fdtfile" which was available in the old kernel. I figured out that I can add a suitable .dtb in the /boot/armbianEnv.txt in the following post. https://forum.armbian.com/index.php?/topic/4817-banana-pi-m1-extra-configuration/ fdtfile=sun7i-a20-bananapi-m1-plus.dtb But there is no way to know which .dtb file is used when this information is not set. Can somebody let …

Hi, yesterday I moved my root partition to a 128GB SSD by running "nand-sata-install" Everything works fine. Now I got a SD-Card in my Banana Pi with one big partition: fdisk -l Disk /dev/sda: 128.0 GB, 128035676160 bytes 30 heads, 63 sectors/track, 132312 cylinders, total 250069680 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93d6d043 Device Boot Start End Blocks Id System /dev/sda1 2048 250069679 125033816 83 Linux Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 46 heads, 9 sectors/track, 18706 …

hardware: Orange Pi Zero H2 Kernel: 5.9.14-sunxi Armbian 20.11.3 Buster ethtool version 5.9 get error on cable-test option. full log: http://ix.io/2Icy sudo ethtool --cable-test eth0 netlink error: PHY driver does not support cable testing netlink error: Operation not supported

Hello to all, how can I upgrade the kernel to 4.6.2 from 4.5.2. I have a lamobo r1? Thank you Paul

Hello all. I am having problems making nand-sata-install script work for installing to my external HDD. I used this (or similar) script in the past on loboris' images and it was working. After some time and experimenting with other images etc. I settled on Armbian, everything worked great, until I started the same script. I made 30 ish GB partition for the system and leave the rest as NTFS storage partition for mounting it later on the OS. But with armbian's script, i couldn't get my HDD to work with it. I am choosing to boot from sd and system from USB (sata) option, choosing the correct partition (/dev/sda2 in this example) and starting the process but it f…