Allwinner sunxi

Hi all! I have Orange Pi Zero with armbian kernel 4.14. i'm not sure about the topic name, but to me seems like that. I've managed to make spi tft work flawlessly on my zero. But after i've continued with touchscreen module, i've got problems. After X is started, i can confirm touch is working, because when i touch the display, mouse pointer moves. But in the strange way, very laggy (more than a second to respond), but is works only for ~10 secs, then display stops to redraw. And it is not because of bad contacts! Because i've soldered everything together. And it also freezes if i don't touch it. The system is still working tho,…

The system displays two WLANs, but in reality, there is only one onboard wireless network card. The network connection is slow and disconnected. The official system of Orangepi is normal, this issue occur in the new version of the Armbian system. logs：https://paste.armbian.com/eborebaviq

**1. Summary:** The text console (`tty1`) is permanently stuck at 30 rows by 90 columns after boot, despite the DRM/KMS framebuffer being correctly set to 1920x1080 resolution. All attempts to change the console size via boot parameters, sysfs, or runtime tools fail. This breaks the basic CLI experience on displays larger than VGA. **2. Environment:** * **Hardware:** Orange Pi PC (Allwinner H3) * **Image/Distribution:** "Forky" (appears to be an Armbian-based rolling Debian fork) * **Kernel:** `6.12.68-current-sunxi` (build@armbian) #1 SMP Fri Jan 30 09:28:49 UTC 2026 * **Graphics Stack:** Modern DRM/KMS (`sun4i-drm`). The legacy `fb` driver is not …

OrangePI PC2 Problem report of the current state and improvement favor. --------------------------------------- Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop Keyboard and the monitor resolution.. other All kinds' setting, reboot, when, everything goes off. Therefore it isn't used. --------------------------------------- Armbian_5.34.171121_Orangepipc2_Ubuntu_xenial_next_4.13.14_desktop A keyboard is the monitor resolution only. It's preserved and it's practicable somehow. (1) Setting of other than above, reboot, when, please disappear. I close. (2) Cash of Root becomes full right now, even Mozc, install, can. ---…

I want to put a banana Pi M1 plus a 2.5" SATA drive in a plastic box with only the ethernet and USB ports exposed. This means the onboard power button is not accessible to boot the board. Are you able to power on the board using the GPIO pins? If so please could someone advise which pins to connect to? I also aim to put a 5.5 x 2.1mm barrel connection on the box (with a latching press button switch for isolation) for the +5v supply and connect a short micro USB connector from the barrel socket to the board and also attach the SATA power leads directly rather than powering from the board 2 pin connector to take the load off the micro USB input.

Hi: I use orange pi pc to build a little chromium kiosk for showing some static information(like temperature). most things are fine. but there is a electronic scroll bar which is not running smooth. I check my current environment (armbian 22.08 with ubuntu 22.04) that I am running xorg with fbdev driver. I wonder if there is other things I can try for the hardware? I search the forum and I found there is "lima" driver, but I don't know if I am using it or not. I can see "lima" is loaded via "lsmod" but am I using it currently? I hope the orange pi pc can do better with newer driver. if not, what's the next armbian pi I should buy to get better chromium experienc…

Dear community, Im searching the device-tree overlay files for Banana Pi M2 Berry/ Ultra in dts format. I found: sunxi-DT-overlays But that doesnt contain the sun8i-r40 overlays I want to see how the i2c0, i2c1 and w1-gpio overlay looks!" greetz, hexzhen3x7

I am having a network problem that I can not figure out. First I had to roll back the kernel to version 5.x to even get wifi to work. Since then I have tried all sorts of things. No matter what I do, when I unplug the eth0 the wifi goes away as well. Here is some stuff that might help. __ __ _ _ _ ____ _____ | \/ | (_) (_) |/ __ \ / ____| | \ / | __ _ _ _ __ ___ __ _ _| | | | | (___ | |\/| |/ _` | | '_ \/ __|/ _` | | | | | |\___ \ | | | | (_| | | | | \__ \ (_| | | | |__| |____) | |_| |_|\__,_|_|_| |_|___/\__,_|_|_|\____/|_____/ Version 1.1.1, based on Armbian 23.02.2 Bullseye Running on OPi 3 L…

Hi, I have problem with my Orange Pi PC, where I installed Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. I install python-jabberbot and python-daemon to create daemon to do queries by jabber comunication protocol. When I am active on ssh I get answers from bot in seconds, but when I try get answer without, I must wait about 1-2 minutes to answer. Do you konow what may be responsible for this behavior? Best regards, Leszek Mazur

Hi all! After upgrading to 6.1.24-sunxi64 on my Orange Pi 3 LTS I lost sound at the audio output. dmesg shows this: platform sound_ac200: deferred probe pending I am a newbie to linux - can you, please, provide me a hint how to install the sound card back or revert to the older kernel with a working sound? Thank you!

Hello, On Orangepilite2, USB3 is recognised as USB2. I have connected multiple usb3 devices and results are same. I tried armbian, orangepi Debian, orangepi Ubuntu! results are same same too. For some reason all OS have same issue. In picture mass storage is USB3 device.

I'd love to backup my X2 before I start to mess it up just to have a restore point somewhere at the start. Is it possible with a live linux and dd if / of?

Is there any way to get interrupts working on BPI M2 Berry/Ultra? I tried with raspbian and wiringPI/RPi.GPIO but there is a wait for support() “bug” which has been reported a while ago but no updates have been made in the thread. Currently Im running Armbian 22.11.00. If anyone has some experience or suggestion for a library/smth and is willing to share it that would be great. Thank you for your time.

Hi forum members, when I try to install the headers via: "sudo apt-get install linux-headers-$(uname -r)" I gote these errors: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-headers-5.19.93-sunxi E: Couldn't find any package by glob 'linux-headers-5.19.93-sunxi' E: Couldn't find any package by regex 'linux-headers-5.19.93-sunxi'

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

Hi all! I may need some pointers. I'm using a 2.4" LCD at spi1 which works as /dev/fb0 on armbian bookworm (6.1.63) Meanwhile I've learned frambuffer is deprecated and to be replaced by drm., but ... - I could not find enough details to understand the drm architecture in general - there is a linux/drivers/gpu/drm/tiny/ili9341.c how is that used at all? - How to use drm in armbian? For my case any acceleration is not necessary (and likely not possible even if the H3 has Mali Hardware) but I want to avoid further changes if /fbX is really gone. btw. I want to add touch with shared SPI soon, work in progress. …

can somebody help me create an ap using hostapd i was following this turorial https://seravo.fi/2014/create-wireless-access-point-hostapd but when i chirantan@orangepizero:~$ iw wlan0 info Interface wlan0 ifindex 4 type managed wiphy 1 i cant change the type to AP

I need help i won´t only make an update on cubietruck and bpi-r1 to the last version 5.25 or 5.27 not more. I make apt-get update and apt-get upgrade then i have 5.31 i won´t only 5.2x. Gives an way for an update to 5.2x sorry for my poor english

I've seen this question asked quite frequently here and all the posts end before there is a solution. I think it's time we had a crystal clear discussion on how it can be done. Not just for my curiosity, but for the people who've asked before and for the people who will ask in the future. The reason: Many hats/shields designed for RaspberryPi would otherwise be compatible with OrangePi if Armbian/u-boot didn't direct the debug output to UART0. UART0 is the most commonly used serial connection for hats/shields designed for RaspberryPi. OrangePi has multiple UART gpio so it would make sense for the O.S. (Armbian) to use the one that least impacts the…

Hi. I've always had problem with the composite output (cutted edges) so i gave a try to the latest release. Unfortunatly the video does not show up at all. Anyone still using the old Opi0?

Hello, my orange pi device crashes to white screen at random times. And in this case USB, ethernet does not work.Which logs should I look at?

Hi I'm trying to cancel echo for orange pi pc plus any idea? Methods I've tried and failed so far https://github.com/voice-engine/ec Bu yöntem de doğru hardware bilgilerini bulmadım http://alsa-project.org/db/?f=d75c947d6147c6c00b31ba67bd1a6d62c010cfad

Hi I want to use SPI0 with cubietruck. SPI2 works. However I failed with SPI0. What needs to be done (in script.fex, kernel, etc) to get it work?

I came across this thread but don't think I could get the reset button working (as it should). What am I missing? I followed exactly the correct 'short-ed' pins as the pic, but still no luck. Please suggest. Thanks!

https://github.com/sicXnull/armbian-build/releases MXQ-PRO H313 https://github.com/sicXnull/armbian-build/archive/refs/tags/mxqpro.zip Summary: compile from source halts with error. Traceback (most recent call last): [🔨] File "/home/e***o/Downloads/armbian-build-mxqpro/lib/tools/patching.py", line 491, in <module> [🔨] raise exit_with_exception [🔨] Exception: Failed to apply 2 patches. Log uploaded and available at https://paste.armbian.com/dimokofipe Thanks in advance

Hello i use armbian on my orange pi and have a problem about the wifi connection. I have my orange pi near my 3D printer. When i plug it in, to boot the armbian it works great. But the orange pi will (SOMETIMES) not connect to my wlan. When i change the room and put it nearly my pc, it will connect without any problems... So i check the wifi quality: - near my pc i have a link quality 70/70 - near my 3d printer i have a link quality 64/70 and signal level: 46dBm is this to low for a easy connection?? thank you

I have a 512 MB RAM, 4GB Toshiba NAND PocketCHIP with a custome u-boot supporting USB Booting and decided to test the latest armbian community image for the PocketCHIP (https://github.com/armbian/community/releases/download/26.2.0-trunk.668/Armbian_community_26.2.0-trunk.668_Pocketchip-sd_trixie_current_6.18.20_minimal.img.xz) Boot seems to start fine with all kernel files load confirmed by u-boot output (vmlinuz, ramdisk dtb, etc) but then it goes mute while starting the kernel @TheSnowfield, you are listed as the pocketchip board maintainer (thanks a lot for your contribution! 🙏), any ideas of what am I missing? Do you have a suggestion for a w…

I would like to test or reinstall my nanopi air, but I can only find download for "neo core / air" "testing version" with mainline kernel. In fact I was looking for an uptodate uboot/kernel for legacy kernel or a "usable" version with mainline - that is for me - with an asix module and working WIFI / BT.

I use two Orange pi PC for music studio use with Jack, Ardour and several midi software to use with midi surface controls and keyboards. Everything works great with an external USB DAC but when I try to use the on board DAC through the HDMI output the sound comes out slowed down to maybe a third of the speed making everything sound like it's in slow motion. Any help to fix this would really be appreciated.

Is this the right place to post this type of content? I have a board for Orange Pi. Since I'm usually using windows, it's very inconvenient to burn u-boot. I'll post it to github later if you guys are interested! （Machine translated, English not so good, don't know if the description is apt or not.）

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

Hello, my Cubitruck with Armbian 23.8.1 Bullseye has the false Time and i can't change this. i don't know who is the problem. "date" says me "Mo 9. Feb 19:24:06 CET 2026" but now we have 05:26, when i set date with "sudo date -s "2026-02-09 05:26:00", it looks like it will be override in the next moment, then "date" says sudo date -s "2026-02-09 05:26:00" Mo 9. Feb 05:26:00 CET 2026 root@cubietruck ~ > date Mo 9. Feb 19:26:27 CET 2026 dmesg | grep -i rtc [ 0.000000] Kernel command line: root=UUID=19cf2f1d-1a31-4890-bc04-a2f1c4e4e021 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1…

I've installed Armbian 23.11.1 Bookworm on a FriendlyElec ZeroPi. This version works flawlessly. A few days ago I updated to Armbian 24.2.1 and since then the ZeroPi crashes and hangs. Sometimes it happens after a few minutes, sometimes after a few hours. When it crashes I can't ssh to the device anymore (headless operation). Unbound, AdguardHome and cups aren't accessable, too. The last messages of the journal in an open cmdline window are: Mär 03 20:50:14 azp kernel: rcu: INFO: rcu_sched self-detected stall on CPU Mär 03 20:50:14 azp kernel: rcu: 2-....: (5249 ticks this GP) idle=16bc/1/0x40000002 softirq=20679/20679 fqs=2625 Mä…

Hey Installed Armbian (Ubuntu-noble) with XFCE desktop on an HDD(sda) from SD-card, so I need to have an SD-card in my orange pi zero 2w. I wonder if I can move /boot to an another smaller SD-card? Or do I also need an "mbr" or someting also there u-boot are? /Cheers

I have Armbian running on Banana Pi R1 without networking access. Is this board suppported at all or it is just a waste of time?

Hi all, recently my Banana Pi Pro running Armbian 26.5.1 with Debian Trixie received a kernel update from 6.16.8 (which it has been running on for quite a while without issues) to 7.0.12. Since then, it randomly freezes shortly after booting, sometimes I also can see a kernel panic (see attached pictures). Has anyone else run into this issue? What can I do to fix this? The old kernel no longer appears to be present in /boot, which makes it difficult to return to another kernel (trying to run something like apt-get typically quickly results in the aforementioned freeze).

Hi, I would like to know if there is a way to set the display resolution to 640x480, to use with an old CRT screen from a IBM PS/1 model 2011 that I want to revive. I know about h3disp, but it only has high resolutions, and that old screen does not want to sync correctly to anything other than VGA. I use an Orange Pi One, with a HDMI to VGA adapter and Armbian 5.35, with legacy kernel 3.4.113 Thank you! -Alexandre

Good morning, I am having some problems with the i2c-1 bus, as it sometimes gets stuck even though I have external pull-up resistors. I need to be able to reset the bus to fix it and check the status of the channels, but I don’t know which Linux GPIO corresponds to the physical pins that the kernel associates with PA18 and PA19. I have tried using wiringPi, but it doesn’t indicate this. Can anyone help me? Thanks!

https://www.armbian.com/olimex-lime-2/ Does the image come with and install non free software on the computer? If so is there documentation showing how to do a fully free software installation of the Armbian_community_25.11.0-trunk.546_Lime2_trixie_current_6.12.58_minimal.img image? Free software is software you can use, share, modify and redistribute. Thank you.

I'm experiencing something unusual. A device of mine, running Armbian, cannot communicate with an Android device in my LAN. Otherwise everything else works. My Orange Pi Zero 2w running Armbian can ping all of my LAN IPs (and access theyre net services also) , but fails at pinging an Android device (which is connected through WiFi): "Destination Host Unreachable". Same goes the other way around where Termux runs on the above mentioned Android 15 device but cannot ping ("Destination Host Unreachable") the host running Armbian or access it via ssh (it simply stalls). Everything else works just fine, all of my devices connect w…

I know I'm supposed to log with armbianmonitor -u, but I can't behind that ***** corporate proxy. So I made a strace. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi System load: 0.11 0.24 0.25 Up time: 6:55 hours Memory usage: 26 % of 493MB Swap usage: 9 % of 127Mb IP: 10.aa.bb.ccc 169.254.6.65 CPU temp: 45°C Usage …

As per the Subject, the I2C bus 0 is enabled and detected, but I don't see an addresses being returned when I try the i2cdetect -y 0 command. I have a single PCF 8574A connected with address 0x38. and have double checked the wiring. The PCF8574A did respond on the I2C bus on another SBC. Thanks John

Im trying to connect WaveShare 10" Touch Screen LCD (HDMI) to OrangePI Plus 2E but the problem is that I got greeny picture on the screen. If I connect this display to Raspbery PI 3 I got good clear picture. Any ideas what could be wrong and how to fix it?

Hello, is BPI-6202/6204 supported? It should have A40I CPU, like the M2 Ultra (which is actually supported)

As the title says. I can not get PWM to work. I can type gpio mode 2 pwm and no error. But when I try to access it from Klipper (3D Printer Software and Firmware) it won't work. However if I use gpio 3, in software, gpio 4 turns on. Please help me out here. Thanks, Kevin

until I've installed the 24.05 image the cubieboard2 came up with an HDMI output on video, I have an DVI to VGA Adapter connected and could use an USB Keyboard+Mouse and the VGA Monitor. Since I've installed the Armbian_community_24.5.0-trunk.667_Cubieboard2_jammy_current_6.6.31_xfce_desktop.img.xz on the SD card, the system comes up with an ASCII Console on the VGA Monitor, later the screen gets cleared with only an cursor in the left top and then gets switched off. I've managed before to switch the output of the X-Server from None-1 to HDMI-1-1 using xrandr, but this is only possible with an proper and authenticated Display and I have to use an autolog…

how can i know the name given to the usb port when i connect my arduino to my orange pi pc plus??? I need to be able to connect it but node red does not read it, please help

Hi, I try to install Armbian Bulleye on my Nanopi Neo Plus 2. Well it completed the install, but when it reboot, I keep getting kernel panic. I try installing with the official Friendly Arm image (kernel 4.14 though) and it was fine (both on SD card and EMMC). Below is the serial console dump, also it seems to crash in random places too. Any help will be greatly appreciated. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.12.09 21:53:09 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2022.07-armbian (Nov 30 2022 - 10:43:13 +0000) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(debug):af220ebb-dirty NOTICE: BL31: Built : 10:4…

Hello again... How can I activate the wifi network? I have a nanopi neo plus 2 with wifi, but armbian don't find it. Ifconfig and nmtui don't find the wireless connection. Thank you

Hello, I am trying to run Armbian on my Orange Pi 3 LTS. The official Orange Pi image works normally: Orangepi3-lts_3.0.8_debian_bullseye_server_linux5.16.17 However, when I flash the Armbian image: Armbian 26.2.1 Minimal / IoT I get several boot errors during startup: [FAILED] Failed to start Apply Kernel Variables. [FAILED] Failed to start Dispatcher daemon for systemd-networkd. [FAILED] Failed to start Helper to synchronize boot up for ifupdown. [DEPEND] Dependency failed for Raise network interfaces. The system continues booting, but these errors appear every time. Hardware: Board: Orange Pi 3 LTS Image: Armbian 26.2.1 Minimal /…

Simple to reproduce: Install armbian from Armbian_23.05.0-trunk_Bananapip2zero_bookworm_current_6.1.24.img after setup make apt-get update apt-get upgrade System will do nothing after reboot, LED stays off copying back kernel 6.1.24 brings it back to life again, with the rest upgraded. thanks Michael

I built an unofficial Armbian 6.12.51 (Noble) image using the build tool: Armbian-unofficial_25.11.0-trunk_Nanopiduo_noble_current_6.12.51.img I am trying to get the micro-USB port to work as a USB serial gadget (g_serial / libcomposite). What I have done / observed: g_serial and libcomposite modules are loaded: lsmod | grep g_serial g_serial 12288 0 libcomposite 49152 2 g_serial,usb_f_acm ConfigFS is mounted: mount | grep configfs configfs on /sys/kernel/config type configfs (rw,nosuid,nodev,noexec,relatime) UDC exists: ls /sys/class/udc/ musb-hdrc.2.auto Gadget folder does…

Hi, I am having a problem getting the graphical login to work... What I run is an ubuntu jammy image with gnome, however when I boot with my tv connected via hdmi it seems to work at first but finally I end up with a screen just displaying the above error. armbianEnv.txt contains the line "disp_mode=1920x1080p60" (a mode my TV supports), yet when the device starts it uses the 4k mode - could this be part of the problem? So how could I get this working and how would I ensure that my device only uses fhd resolution, even though my tv can also do 4k? Many thanks!

Hi, this is my first post, my apologies, I could not find a matching topic category for this PCduino3 nano question/issue (no built-in wifi, I use a Roccar wifi dongle) I have successfully built the image using the armbian configuration script (bookworm current), the board boots and runs teslausb, however, I am unable to install the driver for my wifi dongle. The error when starting the install-driver.sh script is "your kernel headers are not properly installed". I tried apt install linux-headers-current-sunxi and kernel-headers-armmp, they install successfully but I still get the same error about the kernet headers not being properly installed. Th…

Hello, I tied to activate SPI an a BananaPI M1 an Armbian VERSION=23.11.1 but didnt succeeded! I activated "spidev" at armbian-config and tried diferent configurations in "armbianEnv.tx. with: overlays=spi0 spi-spidev param_spidev_spi_bus=0 i get roland@bananapi:~$ dmesg | grep spi roland@bananapi:~$ lsmod | grep spi spidev 20480 0 roland@bananapi:~$ ls /dev/spidev* /dev/spidev0.0 roland@bananapi:~$ I installed "Rf24" library for an nrf24l01 module and tried "scanner" "gettingstarted" and my own c++ file. Al long as I define a wrong "CE" pin, I get response from the nrf24I01 modul. Mostly I get some senseless info, but …

Today I noticed that last Sunday a community version of Armbian was released with Orange Pi 4A support. I tried to flash it in different ways just in case, but it just wouldn't boot. I used BalenaEtcher, Rufus and Armbian Imager and neither of them worked. Im new in this stuff, so I wanted to know if someone could tell me if it is something I'm doing wrong.

Hello community Here are the versions I’m using: Kernel: 5.15.48-sunxi OS: Linux nanopineo 5.15.48-sunxi #22.05.3 SMP Wed Feb 19 15:56:03 UTC 2025 armv7l GNU/Linux I’m having a problem. Sometimes, during boot, I see the following log: After this message, the system halts. The only way to fix it is to flash the image again or to boot from an SD card and mount the EMMC which fixes the file system. I noticed that the device doesn’t use the overlay_prefix variable from /boot/armbianEnv.txt. It shows this message: I tried adding the overlay_prefix variable manually in the boot.cmd file, but it didn’t help. …

hello guys, tried to flash the latest debian trixie os from armbain on nanopi neo using armbian-install, but it would never boot up again. any clue?

hi can somebody fix repostiory install list error for chromium as chrome-commen and chromedriver wont install problem: chromium/noble 9:126.0.6478.182-1~deb12u1+narmbian1 arm64 web browser installs with version therefore chromium-common and chromium-driver,will not install because its looking for dependency chromium 126.0.6478.182-1~deb12u1+n1 Without the ":9" i presume he following packages have unmet dependencies: chromium-driver : Depends: chromium (= 126.0.6478.182-1~deb12u1+n) E: Unable to correct problems, you have held broken packages. please can somebody fix

I posted this in the Orange Pi Zero 3 topic earlier but got not response. **How would one go about to get the default u-boot config that is flashed to spi to have netretry turned on?** > If anyone is interested, here is a guide to netboot (pxe) the orange pi zero 3: https://raymii.org/s/tutorials/Netboot_PXE_Armbian_on_an_Orange_Pi_Zero_3_from_SPI_with_NFS_root_filesystem.html

Hello, everyone. I need a case for the orange pi 5b with compartments for 2 or more 2.5 HDDs. Maybe someone has an stl file for a 3d printer? or a 2D drawing.

Hi, I got my OPiZ3 2GB model last week, but it seems to detect as 4GB sometimes. At first, I thought I got lucky and the seller shipped the 4GB model, but I realized it crashes under load when it do. and I have to restart multiple times to get it right. The issue shows up in htop and free, where it reports double the memory and swap. I’m using the Minimal/IOT image with Armbian Linux v6.6. Here's the output from armbianmonitor -u: https://paste.next.armbian.com/iguzunaved The MemTotal value switches between 4GB and 2GB. Any ideas on how to fix this? Thanks!

I have an H618 Android TV Box with 8GB of RAM and 256GB of storage. Any build option results in an error. I would be immensely grateful for any help. Thank you. armbianarm_errors.txt

https://github.com/MaverickLong/MLIR-TIM-VX This is an MLIR-based lowering path from the TOSA v1 dialect to TIM-VX, VeriSilicon's OpenVX-based GPU/NPU ML Framework. It includes the lowering from TOSA v1 to a custom timvx dialect (mirrors the TIM-VX C++ semantics) and a full lowering to C++ source. It is currently on par in inference speed with the vendor ACUITY compiler pipeline while still giving you full control on the graph level. In my own testing, on a Radxa Cubie A7Z \w Allwinner A733, ResNet-50 takes 8.0ms to inference, while the ACUITY-compiled baseline takes 7.3ms according to Radxa. It all starts with Radxa/VeriSilicon's fa…

Hi! Yesterday I upgraded my NanoPi Neo Plus2, during that the kernel version went from 6.12.74 (package version 26.2.0-trunk.478) to 6.18.19 (package version 26.2.0-trunk.626). This morning I noticed, that this kernel is missing the dm-snapshot.ko module. I searched the forum if anyone else is having this problem, but it appears I am the only one using this feature. I use snapshots to create consistent backups of the system. Is there a reason why it was removed and more importantly is there a way to get it back without having to compile the kernel myself? Greetings PS: I should note, that I want the module back in newer kernel versions in the fu…

It boots but does not recognize USB keyboard input. Not possible to login.

Hello, i tried "Armbian_community_26.2.0-trunk.606_Radxa-cubie-a5e_trixie_edge_6.19.8_minimal.img" and wlan didn't work, i think the device tree is broken Radxa-cubie-a5e kernel 6.19.x as a quick fix, I copy the kernel 6.18.x "sun55i-a527-cubie-a5e.dtb" file to the /boot/dtb/allwinner directory to get wlan working.

Hello. After burning Efuse to the Nanopi Neo Core, I can't boot from emmc. It works from the SD card, so I try loading everything into emmc: spl, uboot. But spl doesn't find u-boot, as far as I understand. I'm using the u-boot and dts config from the Nanopi Neo, with some edits to mmc2, since it's not available in the Neo. U-Boot SPL 2024.07 (Feb 25 2026 - 15:51:42 +0300) DRAM: 512 MiB Trying to boot from MMC1 CMD_SEND:0 ARG 0x00000000 MMC_RSP_NONE CMD_SEND:8 ARG 0x000001aa RET -110 CMD_SEND:55 ARG …

hello guys, sorry i had to tag orangepione, only because i could not find nanopi neo in allwinner h3 category. anw, my question is where can i find the older releases of the armbian os, i visited archive but i could not find the image i downloaded like one year earlier which is armbian v25.11 linux kernel 6.12.51 sunxi, there used to be a legacy option in the page related to nanopi neo where i could find all the older releases but looks like it is gone.

I'm running Armbian off NVMe, and flashed the U-Boot SPI firmware (u-boot-sunxi-with-spl.bin → /dev/mtdblock0) so I no longer need an SD card inserted just to get it booting. That part works great. But now I'd like to be able to pop in an SD card occasionally to try other distros/images without disturbing my NVMe install — and it seems that's not currently possible: with an SD card inserted, the board still boots straight from NVMe and ignores the card entirely. Dug into it a bit over serial console: The default boot_targets is fel nvme0 mmc_auto usb0 pxe dhcp — NVMe is checked before the SD/eMMC. Radxa hit the same issue on the RK3588 boards and fixed it upstre…

I managed to start de A5E from nvme, but upgrading the packages fails. Installing armbian-firmware_26.8.0-trunk.125_all.deb failed With: data.tar lzma error.... Several months ago I got the same error but ignored it. Now everything is almost working, I tried to find out what went wrong. I can extract package with dpkg-deb -x on another system. MD5sum is the same on A5E and other system. This problem occurs on sdcard and nvme card. Btw: it is the 4G version of the A5E. Any idea how I can solve this?

I have a Orange Pi Zero2W with Armbian. I flashed a SD-card, and then I copy the system and boot to a usb- hdd (sda) and the system boot to sda Want hdd because It write much data and USB 2 don't take mush more speed. But I get a warning about a file-error or something so I run fsck on sda(hdd) that was a systemdisk, but when I run I choose to do it read-only, but anyway it does not boot any more. I think I can take the usb-hdd and run fsck from another computer? I have one system with Ubuntu on a Intel 6 gen, and Raspberry pi 500 and 5. The Pi-machine have raspberry-pi OS and the other Ubuntu 24.04.Does the machine or system have any significa…

I have an orange pi zero3 with 2gb of ram. Ive installed the current 6.18.43 armbian debian build. It booted fine from SD and I then flashed the boot rom to the eeprom so I could boot from USB (sudo flashcp /usr/lib/linux-u-boot-current-orangepizero3/u-boot-sunxi-with-spl.bin /dev/mtd0) I was able to boot from USB0 fine but not from the USB ports USB1 and 2 on the 13 pin header. With the help of google and some ai I found that if I run the following my sd card is recognised when plugged into usb1 fdt addr bbf107b0 fdt set /soc/usb@5310000 status "okay" bind /soc/usb@5310000 ehci_generic usb reset usb storage That produced: Bus usb…

For some reason, the CPU frequency in Ubuntu is set to 1416000 while the hardware can reach 1512000, which is an improvement of about 6 and a half in CPU performance. I would appreciate a change or explanation. Thank you very much for everything.

Looks like there is a problem with this image. A brand new banana pi m4 berry would not boot from SD. I then tried Bananapi-Armbian_24.8.2_Bpi-m4berry_jammy_legacy_5.4.125_xfce_desktop it boots normally. Kindly review this. Ron

I want to buy the orange pi zero 3w.Can i have hardware acceleration with the images provided from armbian developers?Thank you,in advance.

Deleted.

Subject: Fix for eMMC Internal State Deadlock / Power-Loss Recovery Failure on Allwinner (sunxi) platforms (Banana Pi P2 Zero) Hi Armbian and sunxi developers, I would like to share an industrial-grade diagnostic report and a 100% verified solution regarding a severe, reproducible boot deadlock on Allwinner H2+/H3 platforms (specifically tested on Banana Pi P2 Zero) utilizing onboard eMMC. === 1. SYMPTOM === During rigorous power-cycling stress tests (hard power-off during random kernel init/write phases), the system randomly bricks on subsequent boots, showing a "dropping to shell" (initramfs / BusyBox prompt) or failing completely during the U-Boot phas…

I installed Armbian on my Orange Pi Zero 2W—my first time doing this—but the keyboard doesn't work when I connect it via the USB-C adapter I'm using. I considered an SSH connection as an alternative, but I don't know how to set it up without a keyboard, nor do I know how to configure Wi-Fi and SSH settings via the SD card. Please help.

The system v26.11 rolling for Orange Pi PC Plus running Armbian Linux 6.18.53-current-sunxi cannot boot from eMMC on the Orange Pi PC Plus. The bootloader is looking for an old partition on /dev/mmcblk0p1, whereas the current partition of emmc is identified differently - as /dev/mmcblk2p1. Therefore, it is necessary to use a bootloader from an SD card, which specifies the path to the eMMC partition for subsequent operation.

Hi everyone, I am experiencing a persistent boot issue with my Orange Pi Win Plus running Armbian, used as a headless server. The Problem: Whenever the board suffers a power loss (unplugged) or I issue a system reboot, it fails to start automatically. The power LED stays on, but the system/network never comes up. To get it to boot, I have to go through a frustrating manual routine: manually holding/pressing the power button, sometimes plugging/unplugging the HDMI cable, and repeating this process a couple of times before it finally kicks in. What I have already checked/ruled out: Power supply is NOT the issue: I have tested multiple different power ada…

While doing some testing of multiple things I decided to build 2 images, fresh/new for my nanopineo's also trying to have the resulting image as close as possible to what I have running on the nanopineo's for years since 2022 or so. That was originally Armbian Buster and I have been tweaking the installations to match other computer installations. Main thing is split the root partitions into a rootfs (Btrfs) and a bootfs (Ext4). More recently, I did more changes, such that I can run the whole image as KVM and/or systemd-nspawn container. The 1st image was adding extension 'u-boot-menu'; build ended in success, but have not tested it on HW. I saw in extlinux.c…

Sometimes if your monitor is off and olimex start first and after that just monitor is on you will get "default" resolution : ~> cat /sys/class/graphics/fb0/virtual_size 1024,768 I've created a script that fix that with recompiling initramfs, adding necessary /lib/firmware/edid/1920x1080.bin file directly into it. Feel free to use, suggestions are welcome. P.S. Please add tags A20-OLinuXino-LIME2 and T2-OLinuXino-LIME2 fix_hdmi_resolution.sh

After installing Armbian_community_26.11.0-trunk.62_Orangepiplus_trixie_current_6.18.54_minimal.img.xz on the Orange Pi PC Plus, the USB keyboard does not work.