Allwinner sunxi

I've been reading on the forums on the possibility of having multiple OSes inside 1 EMMC for the Opi PC+. From what I understand, inside a typical EMMC installation, it has 3 partitions: 1) Bootloader partition, which runs first and starts the main partition 2) main partition, contains OS files 3) unallocated free space suppose I have 2 devices: 1. Armbian Jammy Server 2. Armbian Jammy Desktop Now I want to make another device that has 2 OS partitions, like so: 1) Bootloader 2) 1st OS main partition, 3) 2nd OS main partition, 4) unallocated free space I'm thinking of using DD to extract the …

I have an Orange Pi Mini 2. As far as i know there is no official/ unofficial armbian build for this. there are other boards like orange pi pc, orange pi 2 and tritium h3 board whose images run fine for this board. I have also made armbian image builds with orange pi pc as target and these images work on opi mini 2. I would like to know how could i make a build exclusively for orange pi mini 2.

I have an Orange Pi PC Plus (Armbian Bullseye CLI) that I'm using as a NUT server connecting to a Cyberpower UPS. Every 30 minutes the driver stops working and upon further investigation, this looks to be a USB connection issue. Is there some power-saving mode that would cause this or any other known issue? Thanks!

Hello, I have a problem on my orange pi 3 lts. Namely, I have armbian 23.03 Jammy Xfce installed and on some screens it shows normally, on others the image does not appear. I also tried using the Uart converter and it loads everything normally, but then the following message starts appearing every second. [ 161.905394] panfrost 1800000.gpu: js fault, js=0, status=INSTR_INVALID_PC, head=0xa005bc0, tail=0xa005bc0

kernel version Linux bananapim2plus 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux dmesg [ 1065.023248] udc-core: couldn't find an available UDC or it's busy [ 1065.023290] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 1193.665509] udc-core: couldn't find an available UDC or it's busy [ 1193.665534] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2883.115015] udc-core: couldn't find an available UDC or it's busy [ 2883.115040] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2908.077549] udc-core: couldn't find an available UDC or it's busy [ 2908.077574] misc raw-gadg…

https://paste.armbian.com/faquvejaxo works ok for my alternate 2G4 network. Scanning wifi does not show any 5G8 networks. From dmesg: bananapim2plus:brcm:% dmesg |grep -i brcm [ 7.495253] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 7.497405] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.bin failed with error -2 [ 7.497440] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.bin [ 7.871128] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-plus.txt faile…

After running the armbian-install program and selecting option "1 'Boot from SD - system on SATA, USB or NVMe'" the program transfers the contents of the SD card to the drive (SATA or NVMe). And it works. The problem occurs after booting - a message appears about the device being unable to mount /media/mmcboot . And indeed - the contents of /media/mmcboot and /boot are empty. The problem turns out to be the contents of the /etc/fstab file generated on the SATA/NVMe drive. The mount point /media/mmcboot has a only UUID value, but the text "UUID=" is missing before the value. After manually adding it, everything starts fine. If someone could lean in and correct th…

Hi there 👋 I'm using a NanoPi Duo2 with Armbian 21.08.1 Bullseye and Linux jenkins-agent-arm32 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux I want to use an SPI screen on it, but I don't know which library to use to handle the GPIO... I've tested quite a few and none of them seem to work. I have enabled SPI and I2C in `armbian-config` and `sudo i2cdetect -y 0` works (even if nothing is found), but what is the next step? sudo i2cdetect -y 0 [sudo] password for poddingue: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- --…

How to enable kvm/virtualisation on orange pi 3 lts? I want run windows for arm on qemu with kvm, but in the kernel there is no kvm module . How i can add this module to kernel? I know that the allwinner h6 has support for virtualisation.

Hello, I'm using a Banana Pi P2-Zero based on H3 and I want to get Ethernet running. To no avail so far... When building the image, I use this parameters: BOARD=bananapim2zero BRANCH=current RELEASE=jammy BUILD_MINIMAL=no BUILD_DESKTOP=no I use the customize-image.sh script, but I don't change anything related to the drivers (or so I think). There are no patches, overlays or anything like that. I saw this topic but this solution doesn't help: I also tried something like this but it didn't help either: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&emac>…

Machine model: Banana Pi M2 Berry Linux bpi08 6.2.7-sunxi #3 SMP Fri Mar 17 07:58:04 UTC 2023 armv7l GNU/Linux (armbian@next) Mir ist es nicht möglich eine interne Temperatur auszulesen. Brauche dringend Hilfe! Der Link“/etc/armbianmonitor/datasources/soctemp “ exitiert zwar, nur die Datei / das Verzeichnis existiert nicht: nicht vorhanden → /sys/devices/virtual/thermal/thermal_zone0/temp nicht vorhanden → /sys/class/thermal/thermal_zone1/temp Wo soll diese Dateien überhaupt erstellt werden? Anmerkung Es wäre schön, wenn es für den Banana Pi M2 Berry eigene Tags geben würde. Er unterscheidet sich von dem Banana Pi M2+.

Armbianmonitor: I had use armbian-config to change the dts for change pin start status. it worked. but just work when kernel load. it don't effect the uboot. did i missing some step? or it's because my uboot is too old? Thanks, mika

Hello guys, i'm trying to connect that ili9341 display with my m2 zero but it wont work. My armbian Version: Armbian_23-02-0-trunk_Bananapim2zero_lunar_edge_6.1.11_xfce_desktop The display has a pinout that matches with the raspberry pi, so also the banana pi m2 zero would do the job, since it has the same pinout like the raspberry pi has. It uses 26 pins to connect to the banana pi m2 zero gpio output pins. 3 buttons and a touch panel are available but i only want to use the lcd for now. I edited the armbianEnv.txt to open the spi port and added my overlay tft.dts to /boot/overlay-user but i cant get a picture on the screen, Its just glowing …

Hey! I have Lime2-Server from olimex here and get no internet connection. I configured eth0 via nmtui and tried to activate it, but I get: "could not activate connection: the device could not be readied for configuration". Any idea or known issue? best regards armybee

I have good temps and was thinking to overclock it but have no idea how to do it.

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

armbianmonitor output: http://ix.io/4qwA I assume it's crashing as I have no display connected to it. Every few days I just notice I can no longer reach the network folder, but it works after a power off/power on. Not much running on it, samba for file share and deluge for occasional downloads. I also recently run an update, upgrade and dist-upgrade, but it didn't help. I don't really know what should I look for in the log. OS: Armbian buster (21.02.1) armv7l Host: LeMaker Banana Pi Kernel: 5.15.93-sunxiC CPU: Allwinner sun7i (A20) Family (2) @ 960MHz

Hello, I am trying to use my NanoPi neo Plus 2 rev 1.2 board as KVM with help of (kvmd-armbian) and USB-HDMI capture card and USB-A to USB-A cable as OTG for emulation of Keyboard and mouse as HID. I discoverred that If I install "Armbian 23.02 Jammy with Kernel 5.15.y" like the install script from srepac/kvmd-armbian recommends, updated it and installed the srepac/kvmd-armbian piKVM, it installed properly and it is working BUT to my OTG USB HID connection to work I had to convert sun50i-h5-nanopi-neo-plus2.dtb to sun50i-h5-nanopi-neo-plus2.dts and in there find "dr_mode" and change it to peripheral (or otg) to get my HID OTG input to work w…

I had successfully installed Armbian_2022.08.8_Bananapi_bullseye_CLI_5.15.74 on my M1 and copied the system to an SSD which I had attached to the SATA port. Then I had updated the UUID in armbianEnv.txt and running the system from SSD was working fine. The system was running headless in my closet for about 2 months, and I even had no problems to remotely restart the device until today, when it did not come back up after a reboot. I took it from the closed and hooked it to a monitor just to see the following error messages: ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 I suspected a broken SD card but a check on my Ubuntu de…

Hi im not Linux user not all, can someone point me how to enable SPI ? I try this: Enabling SPI Enable the hardware through config: sudo armbian-config switch on SPI in System>Hardware>SPI-spidev & save Update /etc/modules: sudo nano /etc/modules to include the following line: spi-dev Update /boot/armbianEnv.txt : sudo nano /boot/armbianEnv.txt to include the following: param_spidev_spi_bus=1 #origianl is 0 but the resonance measurement.py module expects 1 so easier to fix here param_spidev_max_freq=100000000 The commands to verify the SPI bus should return output like: $ ls …

Good morning, I am using a version compiled with your script for Banana Pi M2 Berry to build a network HiFi streamer, and I am satisfied with it. I have installed LMS and Squeezelite, and everything is working great. Now I would like to add an Innomaker HAT AMP that has a 12V power connector that powers the Raspberry Pi at 5V via GPIO. The GPIO of the Banana Pi M2 Berry is declared compatible with the Raspberry Pi3, but I would like to be sure before frying the board in case it is not. Can you please confirm the total compatibility of the GPIO connector of the Banana Pi with that of the Raspberry Pi? Thank you for your response.

I have an OrangePI h3, I upload the Armbian in the SD card, but independent if the SD card is in or not, the Orange pi always display the both network leds turned on. Therefore I do not know if my problem is related to the SO or any hardware problem.

I downloaded the lastest Armbian image for my Nanopi Neo (Armbian 23.02.2 Jammy with Linxu 5.15.93-sunxi). I then connected my WiFi dongle (D-Link DWA-131) and tried to create AP using armbian-config utility. Unfortunately, the hostapd fail to start even though the status shows "active". root@armbian:/etc# systemctl status hostapd ● hostapd.service - LSB: Advanced IEEE 802.11 management daemon Loaded: loaded (/etc/init.d/hostapd; generated) Active: active (exited) since Thu 2023-03-02 12:32:58 CST; 5s ago Docs: man:systemd-sysv-generator(8) Process: 3656 ExecStart=/etc/init.d/hostapd start (code=exited, status=0/SUCCESS) CPU: 61ms Mar 02 1…

Hi I have old orange pi A20 board with vga https://www.armbian.com/orangepi/ It armbian loads as expected, environmet file I added the fdt line. But after I reboot after command armbian-install after transfering files to the ssd hard drive it board does not start without errors. failed to mount media/mmcboot dependency failed for /boot dependency failed for local file systems <..> you are in emergency mode attached image of the error: imgbb_link

Hi, i need to download version Armbian 21.05.6 Buster with Linux 5.10.43-sunxi , is it possible to do it now and how? thank you

Hello there, I am beyond my expertise (that which is already limited) have found a guide. Now the guide uses ili9486 so it was substitute it will ili9341 as well as the build they used official build am using Armbian_22.11.1_Orangepi3-lts_bullseye_current_5.15.80 and int with a new one found in the fbtft library. I also need to translate for Russian with chrome not their are photos of it working but all I get is a white screen. here is my version of the overlay. /dts-v1/; /plugin/; / { compatible = "xunlong,orangepi-3-lts","allwinner,sun50i-h6"; fragment@0 { target-path = "/aliases"; __o…

Hello everyone, I am new to the world of Orange Pi 3 LTS 1.4 and Armbian. I have very recently installed this os on my Orange, it turns out to work almost everything correctly except Wifi and bluetooth. It is really important for me to get Wifi working for various projects I have in mind and I find armbian very reliable and supported. When I try to connect the Network Manager interface returns: On the net I found various discussions about this but no real solution. Does this happen to you as well? It seems not to recognize the wifi chip. Below is the armbianmonitor: https://paste.armbian.com/iteheqokov …

Maybe there has been a glitch in the update release process? I performed a sudo apt update && sudo apt upgrade and this has pulled down an automated build. Should it had pulled down a supported build instead?

sudo systemctl status bluetooth ● bluetooth.service - Bluetooth service Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled) Active: active (running) since Sat 2023-02-25 16:50:52 IST; 1h 41min ago Docs: man:bluetoothd(8) Main PID: 1131 (bluetoothd) Status: "Running" Tasks: 1 (limit: 2209) Memory: 1.3M CPU: 402ms CGroup: /system.slice/bluetooth.service └─1131 /usr/lib/bluetooth/bluetoothd Feb 25 16:50:51 orange systemd[1]: Starting Bluetooth service... Feb 25 16:50:52 orange bluetoothd[1131]: Bluetooth daemon 5.64 Feb 25 16:50:52 orange systemd[1]: Started Bluetooth service. …

Hi, Firstly I wanted to say thanks for providing builds for the Cubietruck, however unsupported they are. Current build is working after I fixed up the repository and the wired network configuration - learnt a fair amount in one afternoon! Secondly, is it possible using armbian-config to switch to stable repository and a stable kernel and reasonably expect it to still work? Many thanks,

Hi All, I am trying to enable HID gadget on Banana Pi M2 Zero with latest Armbian OS for it. I followed the instructions in following link,but no luck: Switch USB port from OTG to HOST mode I get modprobe: ERROR: could not insert 'g_hid': No such device when I enter modprobe g_hid. I appreciate any help. Thanks

Hi, This will be my first time using Armbian and OrangePi, sorry if theres stupid questions. I want to write a C++ application that uses LVGL to display information on a USB screen and have a few questions. 1) Will I be able to this screen in this setup. It uses the frame buffer (/dev/fb0). There are instructions for RaspberryPi, where its just plugged in and the frame buffer is available to use. 2) If I just use the latest Armbian Ubuntu version for this board what is the newest version of C++ I can use? (C++11/14/17 etc) 3) Is there a tool chain available to be able to cross compile my application (specifically from…

Hi, I've got a pair of OrangePi 3 LTS boards running the CLI only install of Debian Bullseye with a kernel of 5.15.89-sunxi64 and all the latest updates applied. But when I run the 'top' command, I always see a load of 1.0 or higher. Even when the system is completely idle. I'm running the system of the eMMC, not SDcards. I realize that this is really more of a cosmetic issue, but I was hoping someone had a suggestion on how to fix it. The system is mostly idle, it's a test box or remote management system, so it's not really critical, and the load doesn't go high anyway. Cheers, John

Hello, it is been awhile since I used armbian with Orange PI, now I took one orange PI NEO on it's connector is UART0, UART1 and UART2. My goal is to use all UARTS available on board. Googling a little I found the part where I should use BIX2FEX to convert script.bin and insert port definitions there, bot looks like that way is obsolete. looks by default only one uart is initialized: root@nanopineo:/boot# cat /proc/tty/driver/serial serinfo:1.0 driver revision: 0: uart:16550A mmio:0x01C28000 irq:49 tx:11630 rx:0 RTS|DTR 1: uart:unknown port:00000000 irq:0 2: uart:unknown port:00000000 irq:0 3: uart:unknown port:00000000 irq:0 4: uart:unknow…

I have tried several times to install the SD card root partition to a USB I have plugged in It fails to boot after it says it has completed I run it headless

Hello! My problem is with paying for OrangePi Plus 2 (not E), but I haven't found a suitable section. Dear administrators, please fix the split if I made a big mistake. I was installed image orangepiplus/Bullseye_current (Nov 30, 2022) in eMMC. All works is normal. In armbian-config I was run Firmware (Update all packages and firmware). Afeter this the board are not loading from eMMC or external CD with current image Armbian. The Ubuntu from site orangepi.org the loading is normal. In debug-uart I see a cyclical reboot with: <0xdd>!␊ ␊ <0xea><0xfc>q<0xb9><0xf6>Core: 65 devices, 18 uclasses, devicetree: …

Thought this might help other people, so I wanted to share: https://github.com/robbieh/Inky7-BananaPi

Hello, I'm using the Lime2 with 22.11(Desktop) + latest Kernel & it works like a charm. I'm currently toying around with the Mia E-Ink Display (Onyx Boox) and the display goes blank during loading the Kernel. Could the problem be that the refresh rate is not supported? The specs of the display are 2200x1650 with an refresh rate of 38 Hertz. I tried to change that via armbian-config (boot section) but it made no difference. Does anybody know a way to make it work? best

I try to use last images: Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80.img.xz Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80_minimal.img.xz But in both instances DHCP client couldn`t start. If I use old image: Armbian_22.08.1_Nanopi-r1_bullseye_current_5.15.63.img.xz All work correctly, nanopi get IP from DHCP server and I can connecting to it. What reason?

Hi, i am beginner in SBC other than Rapsberry Pi and i just got my NanoPi R1 with case. I try power the board without SD card for the first time and i see that friendlyWRT already installed but i would like to use a general OS. Since i can't download the official OS from friendlyelec, i saw that armbian is another way and might be better. I follow all step in quick start guide page, and can't even get my board boot up. Below is the list of OS that i try with SD card: - Armbian_22.11.1_Nanopi-r1_jammy_current_5.15.80_minimal - Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80 - Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.8…

Hello, after a poweroff command, the board Led switches off but the ethernet port Led still green blinks. The os has well performed the shutdown (I can see this through the UART). How is it possible? Thanks

Hey, I recently decided to give the 22.11 a try on my M1, but I can't get my sata SSD to be the system root and boot again. 18.04 it worked for me with the exact same setup. I used this: https://docs.armbian.com/User-Guide_Getting-Started/#how-to-install-to-emmc-nand-sata-nvme-usb went with armbian-install only option for me was boot from SD and system on sata. But after the preparation of the ssd, the reboot always runs into emergency mode with not really good hints how to solve, or what even the issue is. Any tips or hints are welcomed.

Has anyone managed to get video encoder working with the latest mainline kernel? I'm getting stuck trying to compile the cedar_ve kernel driver from https://github.com/uboborov/sunxi-cedar-mainline I have downloaded the kernel source using armbian-config and then built the sunxi-cedar-mainline kernel driver. However, I fail to load the driver due to version magic: When trying to force the load: But no dmesg message about magic check failure.

Hi everyone, I connected my board with my PC via serial USB. Then I opened a serial with minicom and tried to test it out. I can send the strings from my board to PC without any problems but when I write something on the PC it sends garbage to my board. But, if I connect the TX, RX like: TX->TX RX->RX instead of TX->RX, RX->TX it sends normal from the PC and garbage from the board. I checked my baud rates but everything seems legit. I tried both 9600, 115200 bit rates, I also tried the both voltages (5V, 3.3V) What do you think could cause this problem? I saw this thread but seems like ther…

Bpi M2 Zero Armbian 23.02.0 sid can't change volume alsamixer said: This sound device does not have any controls. How can I fix this issue ?

Hi all, I am new to armbian, it is a wonderful project. I just have a nanopi neo core board, fellow the guide doc, it can be boot from the SD card, but the board has internal 8GB emmc. how can I install the armbian into it, so it can boot from emmc without using SD card? Thanks!

Hi there 👋 I've tried the CSC edge images Armbian_23.02.0-trunk_Nanopiduo2_lunar_edge_6.1.8.img and Armbian_23.02.0-trunk_Nanopiduo2_sid_edge_6.1.8.img and the machine does not want to boot. Is there a more stable image somewhere? FriendlyCore boots on this board. Thanks. U-Boot SPL 2022.07-armbian (Jan 30 2023 - 06:49:28 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (Jan 30 2023 - 06:49:28 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 60 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0 Loading Environment fro…

Hello. Somehow TX on UART 3 is not working. I connected USB-UART converter or the Banana Pi Zero M2 UART 3 Pins (as it shown here https://bananapi.gitbook.io/bpi-m2/en/bpi-m2_gpio_pin_define), set Baud rate, but I can't send anything from the SBC to PC. But I can send messages from PC to Banana pi. The converter is working properly(tested on Arduino). Do you have any ideas why? Physically nothing looks damaged, wires are soldered accurately and correctly.... Some system info $ uname -r 6.1.2-sunxi $ cat /etc/os-release PRETTY_NAME="Armbian 23.02.0-trunk Jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.1 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy …

Hi! I ended up here: My Banana M1 was working well, connecting to a monitor I was able to see it working. But after I removed the sd card (after turning the M1 off) and inserted into a Windows machine (it couldn't read the linux fs, did not format it) it won't start anymore. Tried with all the recommanded SD card software to test with the slowest method possible to detect errors on it, but no error on the sd card. Tried many times to write with the recommanded balena etcher the currently supported images on the sd card, like: Armbian_22.11.1_Bananapi_bullseye_current_5.15.80.img.xz Armbian_22.11.1_Bananapi_bullseye_current_5.15.80_minimal.img.xz Did check their…

Hello armbianers ! Armbian 22.11.1 Bullseye with Linux 5.15.80-sunxi on a banana pi m1 I've connected a lipo battery to my bpi m1, and now when I try to shutdown -h 0, it ends up in a kernel panic and instead of shutting down it remains powered up. Is there anything I can do to fix that? I'd know how to shut it down talking to the axp209 via i2c, but I'm not sure how/where to put that, or if that would be or not the proper way to go. Thanks, George.

Hello, I am using a NanoPi Duo2 with Armbian 22.11 and Kernel 5,15,80. This device uses an AP6216 wireless interface, which I have noticed are pretty common on sunxi based boards. I ran some bandwidth tests and had pretty poor results: [ ID] Interval Transfer Bandwidth [ 3] 0.0000-1.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 1.0000-2.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 2.0000-3.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 3.0000-4.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 4.0000-5.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 5.0000-6.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 6.0000-7.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 7…

Hi. After 2 years uptime it disconnected from wifi and was unable to reconnect even after reboot. I suspect my AC adapter has degraded. Can this SBC measure the voltage? Upd: saw this post: https://raspberrypi.stackexchange.com/questions/112122/wifi-not-connecting-depending-on-power-supply I use NetworkManager and when it starts it usually cannot connect to wifi saying that the pre-shared key is wrong, marking the connection as failed and not re-trying. In particular, the log contained a failed "asking for new key" message. Re-starting the service or manually activating the connection worked. As a workaround I created a *.conf file in …

I have enabled RDP option in armbian-config. It worked before but when I connect and enter my password, after pressing OK on the login screen the rdp tab just closes https://prnt.sc/WQKXky75i28c Can anyone help me? Logs: Jan 12 16:12:40 OrPi systemd[1]: Starting xrdp daemon... Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] address [0.0.0.0] port [3389] mode 1 Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] listening to port 3389 on 0.0.0.0 Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] xrdp_listen_pp done Jan 12 16:12:40 OrPi systemd[1]: xrdp.service: Can't open PID file /run/xrdp/xrdp.pid (yet?) after start: Operation not permitted Jan 12 16:12…

Hi Everyone, Is there anything additional required to enable better performance improvements (kernel patch for TXTS and RXTS are set to 3 each see below link) on a Banana PI running Armbian V21 / V22 ? I have updated the bootloader, and OS, and the performance is still abysmally poor. Mechanical or SSD drive connected to on board SATA yields a whopping 2.7-10 MB/sec write speed using dd with a large block size, or with the iozone tool ~5 upto ~45 for larger block sizes. Still a very far cry from the ~120 after the kernel patch applied in ~2019 => https://forum.armbian.com/topic/10352-a20-sata-write-speed-improvement/ …

Someone has any experience changing the A20 to A20-H, our provider offers to us this new version, but I'm afraid to be software incompatible.

I have a solar application for PC, so my goal is to reduce the power consumption in idle as much as possible. How would one go about this with the latest armbian distros?

Greetings, I'm using latest Jammy on an OPIZ2. I've installed the Mate desktop and enabled the desktop with armbian-config. I get no HDMI output. Am I missing a step? Is the Mate desktop appropriate? Thanks. The system works with the vendor's debian distro, but I'd like something better.

Good afternoon. The problem is indicated in the title. The computer is connected to my monitor via HDMI and the screen resolution is only 1024x768. Which is inconvenient to use. I saw a similar topic raised on the official forum of a single-payer in 2019, but no one answered there. Is this a problem of the computer itself or the Linux kernel or drivers?

My Opi3 has been running armbian for over 2 years (edge kernels & usually fully up-to-date). I have been using eMMC & I noticed an apparent slowdown about 6 months ago. As it performs cron-based tasks and is a stats collector, this performance was not noticable but doing a manual BIG dist-upgrade, it seems to take forever (20 minutes to do what should be under 5 minutes). If I run "mmc extcsd read /dev/mmcblk1", the results tell me that the eMMC is at least 90% used whatever that really means. Is this a sign of imminent failure ? hdparm shows read results of 17 MB/s which is actually slower than my alternative SD card boot device and nearly 1/10th …

Hello, does this USB WiFi card work with armbian on Orange Pi 3 LTS? TP-Link Nano AC600 USB Wifi Adapter https://www.amazon.com/dp/B07PB1X4CN/ Does it need any drivers to be installed? If yes, is there any that is working with OPi 3 LTS? Btw I want to use this wifi adapter, because Armbian doesn't work with internal wifi card in this SBC - https://forum.armbian.com/topic/23505-orange-pi-3-lts-no-wifi/ (and sadly Devs didn't release a fix for it)

Hello and Happy New Year, From https://redirect.armbian.com/orangepi-r1/Bullseye_current I downloaded: Armbian_22.11.1_Orangepi-r1_bullseye_current_5.15.80.img.xz and installed. I see a file that shouldn't exist: $ ls -l /*core -rw-r--r-- 1 root root 16789504 Nov 30 11:55 /qemu_fstype_20221130-195503_13162.core A short while later I found this: $ armbian-add-overlay /etc/keys-h3.dts /usr/sbin/armbian-add-overlay: line 62: /lib/modules/5.15.80-sunxi/build/scripts/dtc/dtc: cannot execute binary file: Exec format error Error: dtc does not support compiling overlays There is a symlink involved: $ ls -l /lib/mo…

Hello, Is there a guide / tutorial on making Kodi run with hardware acceleration enabled on Armbian on Orange PI PC Plus? e.g. like how LibreELEC does it. I have found a bunch of information on different sites and forums, but I can't put it all together. What I know so far: * Apparently the HW-accelerated decoding is supposed to be done on Kodi's side via VDPAU API * The Kodi build in Armbian repos does not have built-in support for libvdpau (?) * ffmpeg, the video decoding library used by Kodi, doesn't support Allwinner GPU out of the box and needs patching * Kodi needs to be re-compiled with the patched ffmpeg vers…

Hi, I try to install Armbian Bulleye on my Nanopi Neo Plus 2. Well it completed the install, but when it reboot, I keep getting kernel panic. I try installing with the official Friendly Arm image (kernel 4.14 though) and it was fine (both on SD card and EMMC). Below is the serial console dump, also it seems to crash in random places too. Any help will be greatly appreciated. =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.12.09 21:53:09 =~=~=~=~=~=~=~=~=~=~=~= U-Boot SPL 2022.07-armbian (Nov 30 2022 - 10:43:13 +0000) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(debug):af220ebb-dirty NOTICE: BL31: Built : 10:4…

I am getting a quite loud audio spike / noise sound at the end of an audio play in python when using the following script: https://gist.github.com/bbence84/04d1935a92a4b4ab3d44bf182ea4bcc1 Wav to be played, but it does it with any other wav or mp3 file: https://easyupload.io/vbat12 It uses the speech_recognition package and the preferredsoundplayer package, but also the VLC python package shows the same when playing the audio. When changing the audio play to be non-blocking for the python script, the issue goes away... Very strange. This is driviging me nuts. I'm on Armbian 22.11.1 Jammy / 22.04.1 LTS, kernel 5.15.80-su…

I'm on Armbian 22.11.1 Jammy / 22.04.1 LTS, kernel 5.15.80-sunxi. Orange Pi Zero LTS. I have the issue that using all available audio players, the first half a second or so of mp3s are cut off randomly. Meaning that sometimes the beginning plays correctly, sometimes part of the beginning is cut off. Repeadetly running the player sometimes works sometimes cuts off the audio. I have tried play, ffplay, both have this issue. The speaker is a small amlfier module, the LINEOUTL output is connected to it, but the right is the same. Any ideas where to look? This is driving me insane. Thanks! I have attached a test mp3, w…

When starting orange pi, it happens that not all the RAM is available. That is, the orange pi has 2 GB of RAM and it is written that there is only 1 GB of RAM. This often happens when restarting using the reboot command. If you turn off the power and reconnect, this problem appears much less often. When 2 gb is available: https://paste.armbian.com/asatebupuw When 1 gb is available: https://paste.armbian.com/bohapeyahi Скрытый текст Скрытый текст

Dear community, I am experimenting with MangoPi board, trying to communicate with the CC2530 Zigbee board . To do so, I need an available UART port, the UART0 (/dev/ttyS0, pins 8 and 10) seems to be occupied by the console, but there should be two other UARTs according to the schematic. Some info: pi@nezha:~$ uname -a Linux nezha 5.19.0-rc1-d1 #trunk Fri Jul 22 12:44:22 MSK 2022 riscv64 riscv64 riscv64 GNU/Linux pi@nezha:~$ setserial -g /dev/ttyS* /dev/ttyS0: Permission denied /dev/ttyS2, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS3, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS4, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS5, UART: …

Hi , I am trying to install headers on my orang pi using command #apt install linux-headers-$(uname -r) getting the following message Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-headers-5.4.27-sunxi E: Couldn't find any package by glob 'linux-headers-5.4.27-sunxi' E: Couldn't find any package by regex 'linux-headers-5.4.27-sunxi' could someone help me in how do I install headers ?, I am trying to comiple a kernel module. thanks

Hello, dear members! I built the mainline kernel 6.0.8 using the config-5.15.80-sunxi64 config, but when I try to boot the system hangs on Starting the kernel. Boot log: U-Boot 2023.01-rc3-00069-g93685d0dcb-dirty (Dec 19 2022 - 11:31:13 +0300) Allwinner Technology CPU: Allwinner H6 (SUN50I) Model: OrangePi 3 LTS DRAM: 2 GiB Core: 50 devices, 14 uclasses, devicetree: separate WDT: Not starting watchdog@7020400 MMC: mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0,…

need help to drive Orangepi pc plus with waveshare 3.5inch display with xpt2046 touch driver. OS:- Armbian 22.11 Jammy XFCE Desktop version Kernal :- Kernel 5.15.y link for the os :- https://www.armbian.com/orange-pi-pc-plus/ link for display :- https://www.waveshare.com/3.5inch-hdmi-lcd.htm can any one help to drive touch screen you can message if you need more information,

I don’t own banana pi but I’m thinking of buying it for the project we’re going to do. I have raspberry pi zero but mediapipe is not working. Can I install this library on m2 zero? I would be glad if you help. Thank you.

I have orange pi zero board ..i searched a lot for changing boot splash screen ( currently "armbian universal operating system" which is enabled by adding bootlogo=true in armbianEnv.txt ) I have tried Plymouth it is not working After searching lot i knew about if we can replace bootsplash.armbian , it can help because then neither we need to change uboot packages nor we have to add quiet splash like words etc in armbianEnv.txt. https://github.com/armbian/build/tree/master/packages/blobs/splash. With help of this bootsplash-packer Can anyone list me some steps ( in short ) How to run this script and create…

Hello, my name is Wolfgang and I´m from Germany and hope you can maybe help me. First I have no knowledge related to the nano PIs. I bought an R2D2 from Deagostini. The R2 has a board which looks like an nano PI air. It´s called DRCC H3 V2.0. The R2 has different sounds and video seqeunces which can be played by R2. My quetsion is now do you think it´s possible to change or add sounds to the board? Thanks in advance Wolfgang

I don't own banana pi but I'm thinking of buying it for the project we're going to do. I have raspberry pi zero but mediapipe is not working. I'm thinking of doing image manipulation and this is the most important library in my code. That's why I'm trying to do a detailed research because my budget is limited. Thank you for your help 💯

Trying to run mainline kernel on allwiner V3. U-boot: compiled and successfuly runs with some patches. After starting u-boot, I'm loading dtb and kernel into memory and trying to boot the kernel, but nothing happens. I need any help to solve a this issue. Скрытый текст diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 43951a7731..af7d16076a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -693,6 +693,7 @@ dtb-$(CONFIG_MACH_SUN8I_V3S) += \ sun8i-s3-elimo-initium.dtb \ sun8i-s3-pinecube.dtb \ sun8i-v3-sl631-imx179.dtb \ + sun8i-v3-dv8000-imx179.dtb \ sun8i-v3s-licheepi-zero.dtb dtb-$(CONFIG_MACH_SUN50…

After a clean install of 22.11.1, I edit /boot/armbianEnv.txt to add: overlay_prefix=sun8i overlays=uart3 i2c0 spi-spidev param_spidev_spi_bus=0 and reboot. After the reboot I list the /dev files of interest and there is/are no "spi*" entries: pi@orangepipc:~$ ls /dev/i2c* /dev/spi* ls: cannot access '/dev/spi*': No such file or directory /dev/i2c-0 /dev/i2c-1 pi@orangepipc:~$ Not sure if it makes any difference but I only have power, HDMI, and RJ45 connected to the board at this time, and nothing connected to the GPIO pins. Below are the states of two files, one from which I got the BOARDFAMILY, and …

Hello! I try to connect to OrangePiPC by serial console. I tried using UART1 (add overlay & switch console to ttyS1), UART3 (ttyS3) and ttyS0 (debug port). But always I can see output (with kernel or ) but on my host computer (ubuntu 20.04) I see login prompt and can't enter anything. I tried change speed but not login. Even when I stop serial-tty@ serivice and start minicom without luck. Can you help me?

Hello. I have several new NanoPi-NEO Core devices. OS FriendlyELEC (Ubuntu 16.04.2) was already installed on them, and it does not allow me to boot from the SD card. There is an image created by a script emmc-backup.sh How do I deploy this image?

Hi, I finally have time to get back to my little project. I've been trying to get a working display with tinydrm for an ILI9341 base lcd. My setup works on OpenWrt with the older fbtft driver, but now I'd like to go back and try Armbian (current release is Jammy) on it. My first try with devicetree overlay seems functional but not correct. The display just show garbled data (see attached). What could be the problem with it? This is my env. verbosity=1 bootlogo=false console=both overlay_prefix=sun50i-h5 overlays=usbhost1 usbhost2 spi-spidev param_spidev_spi_bus=0 rootdev=UUID=e0ed80c4-a252-4d96-ad61-78b7834d6b8d rootfstype=ext4 user_ov…

Hi: I use orange pi pc to build a little chromium kiosk for showing some static information(like temperature). most things are fine. but there is a electronic scroll bar which is not running smooth. I check my current environment (armbian 22.08 with ubuntu 22.04) that I am running xorg with fbdev driver. I wonder if there is other things I can try for the hardware? I search the forum and I found there is "lima" driver, but I don't know if I am using it or not. I can see "lima" is loaded via "lsmod" but am I using it currently? I hope the orange pi pc can do better with newer driver. if not, what's the next armbian pi I should buy to get better chromium experienc…

Hi, We are using trying to use Banana PI M2+ for our application , we mainly use UART and Ethernet on module. uname -a details are below. Linux bananapim2plus 5.15.74-sunxi #22.08.6 SMP Tue Oct 18 07:00:33 UTC 2022 armv7l armv7l armv7l GNU/Linux We Enabled UART 3 by adding below command line on /boot/armbianEnv.txt as overlays=uart3 Pin Number: 8 & 10 We can able to transmit and receive data for uart3. We need to enable one more UART to communicate, We tried overlays=uart2 , We failed to enable, Can anyone guide us to enable one more UART in Banana pi M2+ Regards, …

I have Orange Pi Plus 2 running Ubuntu Bionic with Armbian Linux 4.19.62-sunxi and I would like to upgrade it to recent Armbian build based on Ubuntu Linux Server and move OS to SSD connected to one of USB ports. I tried to use Armbian_22.08.2_Orangepiplus_jammy_current_5.15.69.img.xz but it does not connect to both HDMI and network. I tried unofficial command line interface images from product page and weekly released unsupported community builds. Behavior of all these builds is the same - no output to HDMI, no network connection. Finaly I found that recent image for Orange Pi Plus / Plus 2 which boots is Armbian_22.08.1_Orangepiplus_jammy_current_5.15.63.img.xz.…

I have a working BPi M1 with [ 0.000000] Linux version 5.15.25-sunxi (root@d72d155687c7) (arm-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #22.02.1 SMP Sun Feb 27 09:23:25 UTC 2022 Due to inconvenient USB placements, I thought using OTG micro USB (the one right next to the SD slot), but it doesn't seem to be operational. I bought a Micro USB Male To Female OTG Adapter Cable, but the attached devices are not detected neither connected to OTG port, nor to the normal power-in micro USB connector (lo…

Hello, In a GOLANG based, RPi 3B+ project I am using the https://github.com/stianeikeland/go-rpio package to read the state of the GPIO-s. I am planning to set up some Banana Pi M2 Berries with the same software. The package - as it was expected - doesn't work with the M2 Berry. I could adapt the package for the Berry, but I don't know which peripheral chip is used in it. Does anyone know which peripheral chip is used in the Berry? (The schematic diagram on BPI's page is useless). Thanks, G.

Hi to everyone, I configured Network Manager to have a local-link connection (eth0-ll) as DHCP fallback (eth0-auto). When I do the following: Connect Orange Pi in a net without DHCP, obtaining a local link address Unplug ethernet cable Plug another ethernet cable connected to a network with DHCP If step 2 and step 3 are executed rapidly, the Orange Pi doesn't detect the network switching and eth0 keeps its local-link address. When I perform such steps slowly, Orange Pi detect which ethernet cable is not plugged in and then everything works as expected. How can I increase the refresh rate of …

Hello, despite using several threads (links below) and one whole week of work, either nothing or only backlight of my display work. Could anybody provide the forum with an image or .debs, please? Or step by step tutorial (adapting existing tutorials) didn't work for me. Thanks https://forum.armbian.com/topic/7233-bananapi-pro-7-touchlcd-with-debian-buster-and-mainline-kernel-5xxxx/ https://forum.armbian.com/topic/14560-sun4i-drm-and-lcd-panels/ or

We flash hundreds of Orange PI 3 LTS boards with stock Armbian Debian Bullseye via nand-sata-install to install it on the onboard eMMC storage. Some boards after running for a week or more would randomly give this error and fail to boot: Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay* (did the system wait long enough?) - Missing modules (cat /proc/modules: ls /dev) ALERT! /dev/mmcblk0p1 does not exist (initramfs) We can turn the board on and off as many times as we want, the error persists. We can fix the problem by booting it fr…

I had success with @ubobrov's sunxi-cedar-mainline driver before on H3 devices. I'm trying to get it to work on the Orange Pi 3 LTS (H6) however it keeps giving the following error: sunxi-cedar 1c0e000.video-engine: syscon failed... Any help would be much appreciated. dmesg: [ 6.167614] cedar_ve: loading out-of-tree module taints kernel. [ 6.167700] cedar_ve: module verification failed: signature and/or required key missing - tainting kernel [ 6.168445] sunxi cedar version 0.1 [ 6.168601] [cedar]: install start!!! [ 6.168654] cedar_ve: cedar-ve the get irq is 23 [ 6.168673] sunxi-cedar 1c0e000.video-engine: assign…

Hello! I try use UPort 1150 on my OrangePIPC+ board, but got error misiing firmware. After lookup I check that this files was missed, so I copy from RaspberryPi4 board (with Armbian 22.04) moxa folder & ti_3150.fw, ti_5052.fw. Then after reboot all work ok. So, is this that I missed in configuration or this is a bug? Regards, Alex

I would like to set a GPIO to output-high during the boot. In this case, the GPIO is PG0 whose number is 192. The device tree overlay is /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-a64"; fragment@0 { target = <&pio>; __overlay__ { gpio_out_override_hog { gpio-hog; gpios = <192 0>; /* PG0 */ output-high; line-name = "PG0-gpio-hog"; }; }; }; }; However, after the application and reboot, I do not see any init information in "/sys/kernel/gpio" about GPIO 192. There is no "/sys/class/gpio/gpio192" folder existed after boot either. Is there anything wrong in the overlay file?

Hello all, I setup an orangepi plus2 with Armbian_22.08.2_Orangepiplus_bullseye_current_5.15.69.img I follow tuto and it worked with boot on SD card. I run nand-sata-install Then, I reboot. I was in safe mode and try format emmc Then I reboot again Since, I have only green light. I connect to COM port and see that : U-Boot 2022.07-armbian (Sep 21 2022 - 18:37:27 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Plus / Plus 2 DRAM: 2 GiB Core: 65 devices, 18 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading…

Hello, I've been running Armbian for a while on an Orange Pi Zero without any issue. Every now and then I perform an apt update && apt dist-upgrade on that board but today the upgrade process failed with the following error and I'm not sure how to fix it. renaud@AnetA8:~$ sudo apt update && sudo apt dist-upgrade -y Hit:1 http://ports.ubuntu.com focal InRelease Hit:2 http://ports.ubuntu.com focal-security InRelease Hit:3 http://ports.ubuntu.com focal-updates InRelease Hit:4 http://ports.ubuntu.com focal-backports InRelease Hit:5 http://armbian.hosthatch.com/apt focal InRelease Reading package lists... Done Building dependency tree Readin…

Hello, I have an orange pi plus 2 device. but Armbian 5.69 (5.75 or latest version) above Orangepiplus Ubuntu xenial default can be the url for desktop version. Can you please give me the working url? (By the way, I couldn't find a section for orange pi plus 2 in the forum. )

I had to reapply u-boot image. So, I did it by armbian-config and later by "dd" command. In both situations this is failing (please see u-boot messages printed by serial). I was restoring the image (I have backup images of my SD card) and trying again. What may be the problem? I had linux-u-boot-orangepi*-current 22.08.6 installed. As below - please note Verifying Checksum ... Bad Data CRC BTW. I tried the same on Orange Pi PC and Orange Pi Zero - the same result (fail to boot). => version U-Boot 2022.07-armbian (Oct 18 2022 - 07:35:20 +0000) Allwinner Technology arm-none-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Archite…

Hi, I am stuck integrating IR in my board banana pi m2 zero. Can anyone guide me to setup IR?

fb_st7789v spi driver not getting on orangepi pc plus in 5.15 kernel in following issue SPI driver fb_st7789v has no spi_device_id for sitronix,st7789v

Can you power Prime with OTG port? Or does only PSU work?

Hello, I have a problem with uboot, during its scan of USB buses, it blocks for several tens of seconds, displays an error, then boots. Sometimes it blocks completely and it takes several ON/OFF attempts to get it started. I'm using Nano Pi Core LTS with the mini-shield, I have over 20 and it's happening on all of them. This is what is displayed when it finally starts : U-Boot SPL 2020.10-armbian (Aug 08 2021 - 15:18:24 +0200) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2020.10-armbian (Aug 08 2021 - 15:18:24 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loa…

Armbianmonitor: http://ix.io/4cYv Hi I'm trying (and failing miserably) to achieve a simple goal with my Orange Pi 3 LTS: to have pin PD15 set as 'output-high' on startup. From reading the documentation, it seems the logical way to go about this task is to create a custom DT Overlay so that's what I set out to do. Based on the Armbian documentation and various examples I found online, I created the following sun50i-h6-gpio-pwr-status.dts file under /boot/overlay-user : /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h6"; fragment@0 { target = <&pio>; __overlay__ { gpio_pwr_pin:…