Allwinner sunxi

It's possible I may have uncovered a bug. I'm having a problem getting a remote share to mount on boot. The mount is attempted before the network interface is ready and I've got `_netdev` on the required line in `/etc/fstab` . . . . //192.168.0.160/raspi /zeus/raspi cifs rw,auto,uid=1001,gid=1002,file_mode=0755,dir_mode=0755,_netdev,vers=3,credentials=/etc/.smbcredentials_raspi_01 0 0 Here is the part of `dmesg` that explains the issue better than I can: [ 41.572110] sun7i-dwmac 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet] (irq=POLL) [ 41.574888] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features suppo…

Short issue description: sometimes after pulling a USB device out it makes OPi3 USB host controller stuck. One or more USB ports are getting unresponsive (sometimes all four of them) and no messages in dmesg about connection/disconnection. No matter what device is used. This thing happens only on the first host controller, the second rear one is functioning and responsive. It happens more often if we push in and pull out four devices in a short period of time. Wherein /sys/kernel/debug/usb/devices is stuck too, we cannot read the info from it and all the utils (vi, cat, etc.) are getting the D state (uninterruptible sleep). "lsusb" is also not working, but can b…

I cannot compile this module - https://github.com/uboborov/sunxi-cedar-mainline I get this: root@bananapim2zero:/usr/src/sunxi-cedar-mainline# make arch=ARM KERNEL_SOURCE=../linux-source-5.10.60-sunxi make -C ../linux-source-5.10.60-sunxi M=/usr/src/sunxi-cedar-mainline modules make[1]: Entering directory '/usr/src/linux-source-5.10.60-sunxi' MODPOST /usr/src/sunxi-cedar-mainline/Module.symvers ERROR: modpost: "arm_copy_to_user" [/usr/src/sunxi-cedar-mainline/cedar_ve.ko] undefined! ERROR: modpost: "arm_copy_from_user" [/usr/src/sunxi-cedar-mainline/cedar_ve.ko] undefined! ERROR: modpost: "kmem_cache_alloc_trace" [/usr/src/sunxi-cedar-mainline/ceda…

Good day Armbian Forums! I'm having some trouble with builds of Armbian (up to and including 21.08.6 | kernel 5.10.60-sunxi) seeing wireless access points that are configured to channels 12 & 13 on my Orange Pi Zero Plus2 boards (H3 + 256mb RAM). Specifically, the default Android image (a generic Chinese-language Android multimedia system) that's loaded onto these boards can see and connect to access points that have been set to all channels (1-13) successfully, but any Armbian image I have tried fails to see anything (and subsequently cannot connect) to routers on channels 12 & 13. Due to the nature of this, I believe it may be a region setting or dri…

Dear Armbian Zen Masters, Please, help me turn on bluetooth on my Orange Pi Zero Plus 2 H5 board (running armbian focal server). This board is up to date (apt update and upgrade). I've enabled bluetooth support from armbian-config on this board. But, bluetoothctl is not working (gets stuck in waiting for response on command execution). Wifi is working fine on this board. (I could easily use bluetoothctl on my khadas vim3 pro board with "current armbian xfce desktop" on it) Waiting for your response. (Please, find the relevant board info below.) Thanks in advance, Spherulite. -------------------------------------------…

Hi, I thought I'd share this in case anyone else is in the same situation as I. I've been trying to get my Orange Pi Lite to boot the latest (Aug 26 2021) images. I've tried Focal, Bullseye and Hirsute, and the Lite doesn't seem to care for any of them. "Armbian_21.02.1_Orangepilite_buster_current_5.10.12_desktop" from the Archive section does boot, as do the versions of Ubuntu and Debian from the Orange Pi website. Perhaps if I had a serial terminal connected I would be able to troubleshoot this, but I don't yet. I'm using a Sandisk Ultra A1 64Gb and I'm monitoring my power supply with my oscilloscope and haven't noticed any dips belo…

Armbian_21.05.1_Nanopiduo_focal_current_5.10.34.img boots (updating via apt upgrade also causes it not to boot any more) Armbian_21.08.1_Nanopiduo_focal_current_5.10.60.img does not When I examine the SD card it hasn't expended from image (makes sense since the heartbeat never starts).

Hi My Orange Pi PC shows 21.08.5 armbian version in /etc/os-release and /etc/armbian-release but 21.08.2 with uname -v Why don't match the versions ? Thanks

Hello, I am making a board coupled to a NanoPi Neo Core, and a RS485 converter to its UART2. The chip is a MAX1478 and I use the RTS (PA2). this is my armbianEnv verbosity=1 bootlogo=false disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=cpu-clock-1.2GHz-1.3v i2c0 i2c1 uart1 uart2 usbhost0 usbhost1 usbhost2 rootdev=UUID=a37457d6-57d2-4f17-a684-157b1a309a73 rootfstype=ext4 user_overlays=neo-core-stable-mac double-spi ds1307 param_uart2_rtscts=1 param_uart3_rtscts=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u if i run the command, cat /proc/tty/driver/serial |head -8 uart:16550A mmio:0x01C28800 irq:53 tx:120 rx:0 RTS|DT…

I use Orange Pi PC+ with installed Armbian 21.08.3 on eMMC. On system i can't access to mmcblk0 device. In dev directory exist only mmcblk2* files related to eMMC. How can I enable access to the SD card ?

/var/log/Xorg.0.log: [ 59.326] (EE) AIGLX error: sun4i-drm does not export required DRI extension [ 59.550] (II) IGLX: Loaded and initialized swrast [ 59.550] (II) GLX: Initialized DRISWRAST GL provider for screen 0 [ 59.550] (II) Initializing extension XFree86-VidModeExtension [ 59.551] (II) Initializing extension XFree86-DGA [ 59.553] (II) Initializing extension XFree86-DRI [ 59.553] (II) Initializing extension DRI2 [ 59.564] (II) modeset(0): Damage tracking initialized [ 59.565] (II) modeset(0): Setting screen physical size to 508 x 285 [ 60.561] (II) config/udev: Adding input device sunxi-ir (/dev/input/event1) [ 60.561] (**) sunxi-ir…

How is i2c1 and i2c2 mapped on Nanopi Duo? I can configure in armbian-config, but all the Duo pin diagrams only show i2c0.

My third Orange Pi Zero came last week, yesterday I plugged it and had heating issues... So I started reading, learning and testing.... Setup: OPiZ-1: 256 MB, no SPI flash - Has extension board plugged - for comparison OPiZ-2: 512 MB, with SPI flash OPiZ-3: 256 MB, with SPI flash (new one with problem) Test conditions: All with (newish) Sandisk Ultra 16 GB Class 10 All new formatted (SD Formatter) and burned/validated (Etcher v1.0.0) with Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img All on my desk - side by side, ambient temperature 25.0-25.1 C (20 cm from boards, no air flow) No case, no passive/ac…

My Opi first not start when i edit armbianEnv.txt. what am I doing wrong? "For proper hardware support you need to edit /boot/armbianEnv.txt and add: fdtfile=sun7i-a20-orangepi.dtb following by reboot."

Hi, I use three ZeroPi hosts as USBIP hosts top just offer USB devices. The kernel till last update on one device was Linux usb2 5.10.43-sunxi #21.05.6 SMP Mon Jun 21 15:07:45 UTC 2021 armv7l GNU/Linux and the new kernel on the once device that makes issues now is Linux usb3 5.10.60-sunxi #21.08.2 SMP Tue Sep 14 16:28:44 UTC 2021 armv7l GNU/Linux The issues are that one of the USB devices become unavailable after some hours and I see this in the syslog: Spoiler Oct 13 18:36:39 usb3 kernel: [43038.026466] usbip-host 4-1.1: failed to unlink 1/1 urb of seqnum 354788, ret -43 …

After installing the Bullseye version in the Orange PI3, I launched the Kodi installation. The videos however are in slow motion, with the audio at normal speed. Are there any codecs missing? The video driver? Thanks

https://redirect.armbian.com/nanopiduo/Focal_current Tried to flash a couple of times, but it never makes it to the heartbeat led. Will try other releases. This one boots https://armbian.systemonachip.net/archive/nanopiduo/archive/Armbian_21.05.1_Nanopiduo_focal_current_5.10.34.img.xz

I am trying to configure my Banana Pi M2 Zero to use UART to communicate with my 3D Printer. I used Armbian config to setup UART 3 (Pins 8 & 10). I can't seem to communicate over the port. How do I test and do I need to make other config changes? Thank you!

Hello everyone, After many investigations, it was found that its function configuration was incorrect: | \ | | _ \(_) | \ | | ___ ___ | \| | |_) | | | \| |/ _ \/ _ \ | |\ | __/| | | |\ | __/ (_) | |_| \_|_| |_| |_| \_|\___|\___/ Welcome to Armbian 21.08.2 Focal with Linux 5.10.60-sunxi System load: 65% Up time: 0 min Memory usage: 15% of 491M IP: 192.168.4.107 CPU temp: 52°C Usage of /: 8% of 29G Last login: Thu Sep 30 15:58:24 2021 from 192.168.4.98 sam@nanopineo:~$ gpio readall +-----+-----+----------+------+---+-NanoPi-NEO--+------+----------+-----+-----+ | BCM | wPi | N…

How I solve this problem or is it an Ambrian bug? Maybe a better question is what is causing these repeated messages. I am at a loss to finding a solution. BOARD=bananapipro BOARD_NAME="Banana Pi Pro" BOARDFAMILY=sun7i Spoiler --< CUT >-- [ 50.900954] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.900982] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 50.976400] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.976437] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 51.025829] ieee80211 phy0: brcmf_fweh_ca…

Because I'm a glutton for punishment, I decided to test a bunch of PCDuino3 images. Hopefully this will be helpful for someone. Feel free to double-check my work. 3.X kernels work perfect. 4.11-4.14 no HDMI Audio 4.19-5.8 there's a bug where the console won't show up if you connect a high resolution screen. It complains about not enough memory reserved for the frame buffer. So if you have a blank screen, it's possibly working, but you just can't see anything. Also, still no HDMI audio even though it's built into the kernel. 5.9-current hangs at "Starting Kernel" showing in the serial port.

Hi forum, I ran an apt-get upgrade a few days back and here linux-image-current-sunxi:armhf was updated from 21.05.6 to 21.08.2 After reboot my SATA was gone. There was nothing in the logs which would have indicated that something is wrong. After I reverted back to 21.05.6 apt-get install linux-image-current-sunxi=21.05.6 apt-get install armbian-firmware=21.05.8 apt-get install linux-dtb-current-sunxi=21.05.6 everything worked again. Has anyone experienced something similar ? Regards Volker

I'm not sure if this is a bug that needs to be reported and I don't know what issues it may be causing, if any. ----< CUT >---- Sep 16 08:55:56 loki kernel: [35972.411737] ieee80211 phy2: brcmf_fweh_event_worker: event handler failed (72) Sep 16 08:55:56 loki kernel: [35972.465736] ieee80211 phy2: brcmf_fweh_call_event_handler: no interface object Sep 16 08:55:56 loki kernel: [35972.465781] ieee80211 phy2: brcmf_fweh_event_worker: event handler failed (72) Sep 16 08:55:56 loki kernel: [35972.471791] ieee80211 phy2: brcmf_fweh_call_event_handler: no interface object Sep 16 08:55:56 loki kernel: [35972.471838] ieee80211 phy2: brcmf_fweh_event_worker: eve…

Hello i cant get orange pi zero 2 hotspot working with supported image bullseye. Did anyone got it working? Thank you

Hi! Armbian_21.08.1_Orangepiprime_focal_current_5.10.60_xfce_desktop sometime failed to boot. No green indicator, and black screen. Tried to decrease CPU max frequency sudo nano /etc/default/cpufrequtils ### ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=ondemand ### but still failed to boot sometimes. Armbian_5.75_Orangepiprime_Debian_stretch_next_4.19.20_desktop have been installed before and boot fine during 2 years.

Hello, i update my OrangePiZero OS from Linux 5.10.43-sunxi to Linux 5.10.60-sunxi my screen fbtft spi lcd stop working , the screen is black. If there is a solution to this issue I would love to get help, thanks! here my configuration (work on 5.10.43). (Armbianmonitor link of 5.10.43 on top) (Armbianmonitor link of 5.10.60 Attached as a file ) fbtft.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; }; }; fragment@1 { target = <&pio>; __overlay__ { spi1_cs_pins: spi1_cs_pins { pins = "PA13"…

I know, using an old Banana Pi M1 for desktop doesn't make sense at all. I would prefer having help or/and advice clearing the problems I've encountered, instead a discussion why I'm testing a desktop environment on a BPi M1. Tested with Armbian 21.08.01 Buster / 5.10.60 After the initial boot nano or / and armbian-config doesn't work. A reboot solves this issue. After the second boot I changed verbosity to 7 and console to serial. All other changes where made throu armbian-config. Changing Pi's name works, but changing console's layout doesn't. Never mind, that is a minor problem, which can easily solved by hand. So I did "firmware upgrade" and rebooted m…

**Is this the correct location, or it should be at the other supported boards? It seems that DT overlays are not working root@orangepizero2:~# cat /boot/armbianEnv.txt verbosity=1 console=serial disp_mode=1080p60 fb0_width=1280 fb0_height=720 rootdev=UUID=b8899b39-b6cb-4718-bdbb-e1b39816db74 rootfstype=ext4 overlays=w1-gpio param_w1_pin=PC9 param_w1_pin_int_pullup=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Boot log: Spoiler [41]HELLO! BOOT0 is starting May 13 2020 14:10:04! [46]BOOT0 commit : 593cf83 [48]set pll start [51]periph0 has been enabled [54]set pll end [56]unknow PMU [57]PMU: AXP806 [64]vaild para:1 select dram …

This is a simple one, but the most annoying. The only Linux distribution I can not get to work in the Armbian on the Banana Pro. Sandisk 32Gb Class 10 MicroSD card. A USB power supply that does supply sufficient power and current. I write the image to the MicroSD card, insert it into the Banana Pro's card holder, power it up, the red LED lights up and ................. that's where it stops. No heartbeat on the green LED. The one thing I notice is that the image I download has only got one partition on it and that's the ext4 partition. It does not have the small FAT formatted partition and I think this is where it all goes wrong. …

Hello, I have problems with the u-boot both with the prebuild "Armbian_21.05.1_Nanopineo_buster_current_5.10.34" image from the armbian.com and with the "Armbian_21.08.0-trunk_Nanopineo_buster_current_5.10.59_minimal" image built form sources . First of all, the u-boot versions are different. The prebuilt image has "U-Boot 2021.04-armbian" and the second one - "2020.10" The board boots ok with the both images, but the u-boot does not see the SD card properly and is not able to load the environment file from it: "Loading Environment from FAT... Card did not respond to voltage select! : -110" Is there any fix for this problem? Thanks, …

I'm running gentoo on my Orange Pi PC. it's powerful enough to build gentoo, and its ethernet is fast enough to build from NFS.

(Finally this forum lets me enter a new topic. It's failing most of the time, making it really hard to solve my actual problem if the infrastructure also fails.) I'm using an Orange Pi Zero board and try to make it talk to a radio module via SPI. The whole thing already works on a Raspberry Pi so the module and cabling is correct. But the module doesn't respond to requests on the Orange Pi. Since this doesn't do anything, I searched for issues like this and along the way found an SPI loopback tool. I tried it and it returned all zeros. The tool readme suggests that the MOSI and MISO pins are not connected, but they are. I checked and resoldered those pins and …

Hi, I had until yesterday an Armbian version from a year ago on the board, until then I never had problems with my network (WiFi). Yesterday I had then made an apt update + upgrate. After that, however, I suddenly had the problem that some access points are no longer found. This is so that my access point (Fritzbox), my mobile hotspot from smartphone (Samsung) and a network of a neighbor is no longer found. Other access points are still found, so there are still WiFi access points available but I can no longer find mine. Now I have installed the latest version today and still the same problem. Manual entry unfortunately brings nothing because the connecti…

I supose the armbianmonitor output doesn't help much. But here is an output from serial console: 3 times reseting before.... resetting ... U-Boot SPL 2021.04-armbian (May 06 2021 - 20:01:01 +0000) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2021.04-armbian (May 06 2021 - 20:01:01 +0000) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: LeMaker Banana Pi I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0 Loading Environment from FAT... Unable to use mmc 0:1... HDMI connected: Setting up a 1920x1080 hdmi console (overscan 0x0) In: serial Out: vga Err: vga Net…

For the second time within about 4 weeks my cubietruck is not coming up anymore after a sudo apt upgrade and reboot. Is there something systematically breaking? I think it is the initramfstools that is breaking it? Now, I have no radio, alarm-clock and I cannot turn on my coffee-maker over the internet and I will probably have to spend a day etching a new SD card etc. I bought a new SD card last time this happened since I figured ist would be related to that, now I think it is a software thing. I use the cubietruck headless over ssh and have no real video output, just audio. I also need to do some cumbersome operations t…

Steps: - Installed "Focal xfce desktop" Orange Pi PC 2 image - Installed mesa-utils - Set display resolution 1920x1080 60hz - Run glxgears Actual behaviour: - running at 30fps Expected behaviour: - running at 60fps or higher Additional information: - glxgears -info output: https://pastebin.com/y4W30MFg

I have tried the image for Buster from the Download page for OrangePi PC Plus, and also built new images from current Git repo. In all cases the device bootloops when it tries to start the kernel. The image from the OrangePi website works ok. This looks like a similar issue as experienced recently with CubieTruck and BananaPi A20 boards (https://armbian.atlassian.net/browse/AR-749) which was fixed with a workaround (https://github.com/armbian/build/pull/2963) Is it possibly the same / similar underlying problem?

Hi, I have ten orange-pi pc plus with Ubuntu 20.04.2 LTS with Linux 5.10.43-sunxi burned onto emmc, and twenty orange-pi pc plus with Focal 21.05.6 with Linux 5.10.43-sunxi burned onto emmc. In an attempt to provoke the same issues we have with Xenial on these boxes, I have all of them rebooting (shutdown -r now) once every 10 minutes. They have all been under test for several days. They are all connected to a LAN backbone, but the LAN is not connected to the internet, so whilst they may be attempting to do unattended upgrades, for example, they are all failing. This is a deliberate part of the test. Of the twenty Focal 21 boxes none have failed. …

I own an orange pi PC PLUS for about a year and when I got it, I tested it and it worked fine when it booted up from the internal MMC, then I tried to make a server and I think I messed up something with the LAMP I was trying to make so I stashed the PI to play with it later. Now when I turn on the PI, it only loops and never loads the OS, so I downloaded Focal and buster from this link and burned them to an SD and it also loops in this screen, https://imgur.com/WzikUoo what could be wrong? my idea is to reinstall the OS to the internal MMC so I can then install home assistant. thanks in advanced.

Hi I trying to return in work OPi+2e board but faced some odd thing. When I trying to boot Armbian I getting temperatures about 180C which leads to shutdown during booting. It reproduceable with all versions from hirsute/5.12.15 back to oldest avaliable bionic/5.4.8 Official Ubuntu xenial/5.3.5 works fine, but /sys/class/thermal/thermal_zone0/temp gives negative readings (like about -76500) Installed on eMMC old RetrOrangePi which is Armbian jessie/3.4.113 also works but gives zero (exactly 0) temp reading. Finger test gives "room temperature" reading and "warm" while old OS works. Definetly not 180C Board itself is from 2017, worked a…

Hi there! I just received three decommissioned BananaPI M1+ from a company and I'm trying to install the latest version of Armbian Buster available on them. Once I flash the image to the SD card (tested and working fine), however, the board goes into boot loop as per the video. The only error that seems to be displayed is "EHCI failed to shut down host controller". If it can be useful to find the cause, I point out that the problem occurs with both Armbian Buster and Armbian Focal regardless of the presence of the "fdtfile=sun7i-a20-bananapi-m1-plus.dtb" line in the /boot/armbianEnv.txt file. What do you think I could do to solve it? Thank you all in advance.

Good morning, I have a NanoPi Neo core where I am trying to use the usb ports (USB1, USB2 and USB3), the first thing to say is that all usbhost is active in armbian-config. The system does not recognize me anything in any of the 3, not a pendrive, or Wi-Fi or anything. If I go to armbian-config, I see that the DTB system that has loaded is that of the NanoPi air, I do not know if it can influence. USB devices receive power when connected. Any idea if I have to activate something else or modify the DTB or something? I have tried adding to armbianEnv.txt this line at the end fdtfile = sun8i-h3-nanopi-neo.dtb but nothing. Thanks and best r…

Hello Igor, first of all thank you very much for your efforts. I used Armbian in the past and wanted install some up-to-date version. However this fails/hangs independent of selected OS either at 'armbian-resize-filesystem' or 'Flush Journal to persistent storage'. The first boot may take some >15min if succeeds. However i can't login after as it accepts no keyboard input. I started testing upwards from very old version (sorry, i downloaded many and only few by Torrent, but i did send you some donation to cover this). Up to Armbian_20.08.2_xxx_5.8.6 it works well, irrespective of debian/ubuntu flavor. So, the bug came with Armbian_20.11…

Hi there, I have an OPi3 box that acts as home surveillance server. It has WiFi configured as AP, client is Android phone with static IP/routing and IP Camera software. Problem is, that there is NO IP routing. I CAN access video / pictures from phone on OPi box, but NOT from my LAN. Below is routing table and iptables. Looks ok but not working. I am able to access (from LAN) WiFi IP of OPi. Also can access video served by "motion" software on OPi. But no direct connection to Android phone. root@orangepi3:/tmp# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 1…

Hi All I am not able to run Armbian Buster from the Downloads page (https://www.armbian.com/cubietruck/) on the CT board. Other images run fine, including: - Armbian_5.65_Cubietruck_Debian_stretch_next_4.14.78 (from archive) - Armbian_5.65_Cubietruck_Ubuntu_bionic_next_4.14.78 (from archive) - openwrt-19.07.7-sunxi-cortexa7-sun7i-a20-cubietruck-squashfs-sdcard.img.gz (from OpenWrt downloads site) The problem is that it endlessly reboots after resetting the CPU. The output from the serial port is shown below. I can interrupt the Autoboot and get to the Uboot console ok. The output from printenv is also shown below. Any…

Good morning, I am designing a board to use a NanoPi Neo Core. By default it comes without Wifi or BlueTooth. I had thought about putting the AP6212 chip on it. Can someone tell me if it is compatible with Armbian in its latest versions? Thank you and best regards!

System: armbian, BananaPi Pro, sd card, sata ssd, usb hdd I manually moved my existing armbian system from sd card to a sata ssd. Then I changed the rootdev in armbianEnv.txt to the ssd´s UUID. After reboot I thought everything was ok. Then after a system update I figured out that the kernel version differs from the installed kernel modules. I think the new kernel and the modules are installed in /boot at /dev/sda whereas the kernel still boots from /dev/mmcblk0p1. How can I fix this? Here some information: root@pi-nas:/mnt/boot# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda …

Hello, for my BananaPi I recently downloaded "Armbian_21.05.1_Bananapi_buster_current_5.10.34.img" and did not get the on-board CAN controller working with this image. I found out that in sun7i-a20-bananapi.dtb (uses sun7i-a20.dtsi) the group name for the CAN pins PH20 and PH21 has changed from "can0_pins_a" to "can_ph_pins" but in the sun7i-a20-can overlay this change had not been done accordingly, and the DT merging failed. So changing "sun7i-a20-can.dts" to: /dts-v1/; /plugin/; / { compatible = "allwinner,sun7i-a20"; fragment@0 { target = <&can0>; __overlay__ { pinctrl-names = "default"; pinctrl-0 = <&can_…

I usually attach a GPS module to OrangePi One to act as a GPS ntp server . GPS serial data can use any UART port. but PPS pulse can use PA7 or UART_RTS, I most connect to PA7, works very well. Recently I bought a GPS modules for Rasberry Pi, it connect the PPS to pin 12, in One it's PD14 But when I set param_pps_pin=PD14 in armbianEnv.txt , it can't work at all . see /sys/kernel/debug/gpio , there is no GPIO 110 (PD14) at all. So don't use PD14 as a PPS pulse input.

Greetings, after a long time I am playing with my old Banana Pi Pro again. This time with the intention to probably use it on IoT purposes. That implies I only need WIFI and the GPIO pins. Which gives some opportunity to save power by powering down every thing else which is not needed. My first approach here is to strip down everything from the device tree I don´t need. That means everything related to: framebuffer hdmi lcd sata display engine ethernet video codec usb ir gpu/mali That resulted in a drop in power consumption in idle from: ~0.990 - ~1.330W to: ~0.700 - ~1.000W …

Hello First of all, thank you for the great effort of the Armbian project. In second place: I have a NanoPi Duo device, which has been working fine with an old version of Armbian. But when trying to use the latest version, it happens that the serial port console continuously gives the following message and does not allow login ... ... [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Started Network Manager Script Dispatcher Service. nanopiduo login: root (automatic login) Authentication failure nanopiduo login: root (automatic login) Authentication failure n…

Hi, I'm using an Orange PI ZERO HC2 + and usb (mt7601u) wifi dongle to create a hotspot. The configuration is as follow <HOTSPOT>WLAN0 [ Orange PI ZERO HC2+] WLAN1 <connected to my box> At startup when hostapd is launched to create the hotspot i get the following output . See below <HOSTAPD ERROR>. My hostapd.conf is below. Wlan0 use for xradio_wlan as physical driver Wlan1 use for mt7601 as physical drive I did some testing. I have the exact same config with a pi3. And have no problem. I tested the hostapd provided with the orange pi on the pi3, it works …

hello, my recent installation of armbian come to failure pretty quickly I was greeted after login by message, that kernel was updated and restart is required. So i did, but it never came up. Not sure if related to update, i didn't even knew armbian has autoupdates enabled. There is not much in uboot log - https://pastebin.com/zyc4WZpf possibly this: Wrong image format for "source" command SCRIPT FAILED: continuing... libfdt fdt_check_header(): FDT_ERR_BADMAGIC Should I increase logging level? MMC boot folder is found fine. My device setup Cubiraboard2 A20 #1 mmc uboot with /boot folder #2 sata h…

gpio load i2c modprobe: FATAL: Module i2c-sunxi not found in directory /lib/modules/4.14.111 By looking at example of WiringPI (for Raspberry), I tried the above command, result is shown. I'm newbie, so I need to figure out how to send commands via i2c to an external device. But first, how do I even enable i2c on Neo Plus2? Or is it enabled on default? I saw on this forum suggestion to add: a line "overlays=i2c0 i2c1" in /boot/armbianEnv.txt However, my boot directory is full, so and I get error 514 whenever I try to add anything to armbianEnv.txt (which is empty) Here's disk usage: I added 10K pull up resistors between…

Before this I used to connect my APM 2.8.4 Flight controller to a Raspberry PI on Ground, Pin 8 and Pin 10. Today I tried to connect it to my orange pi zero plus2 H3. Pin 9, Pin 8 and Pin 10. On armbian-config toggle UART2. When i tried to connect to it using cat /dev/ttyS2 nothing came out. Once a while sent out some gibberish. I set the correct buadrate at 57600 and 91600 to no available. But I know the settings are correct because when I connect using USB through /dev/ttyACM0 it works. I tried ttyS1 and ttyS3 nothing came out of it. On Raspberry I had done this many times just by turning on the Serial Connection using …

Hi folks! So first here is the key question: Did anyone get exactly this combination NanoPi Duo2, ov5640 camera, armbian focal running? If YES, HOW … ? 😊 Details below. btw. buster would be also fine... uname -a output is Linux nanopiduo2 5.10.34-sunxi #21.05.1 SMP Thu May 6 20:13:21 UTC 2021 armv7l armv7l armv7l GNU/Linux I’m quite new to Linux and Armbian and have a slight problem using an Nanopi Duo2 and an ov5640 camera. It works pretty well using the image from FriendlyElec. This has been tested using the mjpg-streamer. Due to this success I’m sure the entire hardware setup is correct. Unfortunat…

Hi, I am looking to Secure Boot Allwinner H3. We use Nano Pi Duo2 with latest Armbian OS. End goal is to have all the OS / Data on the SD Card Encrypted. Can anybody help ?

Hi, i got a Pinebook and install the latest Armbian Image. All is working fine, only the sound output make problems. It isn't matter if i play a mp3 file or a play a YT Video. The sound is just strechted, drawned, like in slow motion. What can i do to solve this issue? Any ideas? Thank you for your help.

The info from "df" show /dev/sda but "lsblk" show a /dev/sdc unmounted unit. The unit is reachable at /media/sata and is added in fstab using the UUID. What's happening? Thanks in advance.

I downloaded the most fresh image Armbian_21.02.3_Orangepipc_focal_current_5.10.12_desktop.img.xz from armbian.com for my board OrangePi PC. I installed it and had a problem with a process lightdm-gtk-greeter which eats 100% of CPU all time after first board reboot. Updating via apt-get update/upgrade didn't solve the problem. First of all i tried to find the solution in the internet and in this site, but all solutions which i found didn't help me. The most close topic for other board is here. Also i tried to run archived versions: Armbian_21.02.1_Orangepipc_focal_current_5.10.12_desktop.img.xz - had same issue. Armbian_20.08.1_Orangepipc_focal_curre…

Hallo, I hope the topic hasn't existed before .. I have an Bananpi M2+ as H5 (64bit). Good Images are OrangePi-PC2 or NanoPi K1 Plus. My problem is, no support of emmc. Are there any known compatible images for the Banana Pi M2 + H5 that work? The NanoPi K1 Plus has problems rebooting and recognizing a keyboard. The OranngeP PC2 works fine, but no emmc support. Thanks and Best wishes, Mahdi2006

Hi, A few weeks ago I downloaded the actual Debian Buster version without desktop. I installed the OS and moved the filesystem to the attached SATA disk. Finally I installed and configured Samba and tested it transferring files form my desktop. Everything worked fine except transferring relatively big files. The files (2 in total) giving problems were a about 3Gb. When transferring a big file the upload seems to stop. The ethernet connection with the BananaPi M1 is completely de-activated. There is only one solution to re-activate as far as I know: remove the power connector and resupply the board. After resupplying the board…

I installed the pyA20 library for controlling GPIO, but I can't get the internal pullup resistor to work anymore. I managed to get it working before, but after playing around with other things, it stopped working. I have a very simple circuit going on, with just a light switch and I'm trying to read the light switch using the internal pull-up resistor. I managed to get it working for a few days, but that's it. I gave up and decided to solder on my own 10K pull-up resistor from the input pin to 3.3V. To my surprise, the results were the same, the input pin floated. Everything works fine with an Arduino. This is all very strange and I hope someone can help me. I'm runn…

trying to read the serial data from the UART1 port then write it on the UART2 port .... this is absolutely easy in the case of just reading the serial data. but now what m really trying to do is to read the serial binary bits which includes the serial data and the framing data ( parity bit/stop bit/start bit) and then write all of these binary bits to the other serial port. how could this be done? how could i read the serial bits without the framing bits being stripped? thanks in advance best regards

Allwinner_H3_Datasheet_V1.2.pdf up to five UART controllers In sun8i-h3-orangepi-pc.dts only 4 How do I use all five? serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = < 0x1c28000 0x400 >; interrupts = < 0x00 0x00 0x04 >; reg-shift = < 0x02 >; reg-io-width = < 0x04 >; clocks = < 0x03 0x3e >; resets = < 0x03 0x31 >; dmas = < 0x15 0x06 0x15 0x06 >; dma-names = "rx\0t…

Hi there, I have configured (successfully with NetworkManager GUI, or TUI, it was quite ago, can see it in /etc/NetworkManager/system-connections/ ) my OPi3 as an WiFi AP. (Needed this as sharing "normal" LAN traffic with video surveillance on same WiFi channel was a disaster). It works, but in "scan" on OpenWRT routers this WIFi shows only as WPA not WPA2 protected. Armbian Buster 21.02.3. Why? How to correct this? Laurent

Hi, I have been running Armbian on OrangePi Lite for more than a year just fine. Then I decided to upgrade and flashed the latest version. Now with the latest version the device looses wifi every few days no matter which wifi device I use. In order to investigate I have plugged additional USB wifi. Some time both wifi work. Then built-in may disconnect and stop working, but USB keeps working. Or vice versa, USB stops working, but the built in keeps working. I have been able to send syslog to an external machine and here what it showed Connection works fine: The next day one of the connections stops working and…

Hi, I have used the official armbian focal image for orange pi PC (https://www.armbian.com/orange-pi-pc/) The issue is in the armbian-config navigate to system -> Hardware you see nothing as shown below Please find the monitor log http://ix.io/2WQv

Hi All, Can anyone help in setting up HifiBerry Digi + with Opi PC Plus with i2s0.The HIfi Berry is based on wm8804 codec and it acts as a master while i2s on Opi acts as a slave I havent any examples of using i2s in slave mode on H3 boards so just need some help. Kernel is 5.10.19 built with Armbian Build system. This is the driver I am using https://github.com/raspberrypi/linux/blob/rpi-5.10.y/sound/soc/bcm/rpi-wm8804-soundcard.c on my PC PLUS This is my dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ {…

Hi. Tell me, has anyone solved the problem with no sound through HDMI? I've tried the latest builds (kernel 5.10 https://www.armbian.com/orange-pi-one-plus/ ) and the sound doesn't work.

I have found other treads that address "tv out not working" but none have been applicable. They point to files that are not on my system. It is an older orange pi zero. I have installed the latest armbian image. Here is the "lsb_release -a" return: Distributor ID: Ubuntu Description: Ubuntu 20.04.2 LTS Release: 20.04 Codename: focal I am currently operating headless and the login splash screen says "Welcome to Arbian 21.02.3 Focal with Linux 5.10.21-sunxi" I am trying to use the 13 pin connector. Pin 2 = ground (shield) and Pin 9 = video signal (center conductor) I have found forum threads about enabling the tv out bu…

Hello. I have the following problem with my Orange Pi PC: When I turn it on, only the green and orange LEDs of the ethernet port are flashing. There is no output on the HDMI port. I have already tried different microSD cards and different images. It used to work perfectly, but all of a sudden it stopped working. Maybe an issue with the power supply (it is the offical power supply 5V 3A DC jack).

I downloaded the armbian focal image for NanoPi NEO/Core board, and it works great. (Specifically, Armbian_20.11.10_Nanopineo_focal_current_5.10.4.img, so it's a few months old.) I'd like to start creating my own image, and I'm all setup to do that, but what I'd love to do is start from the .config file(s) used to create the image I'm using. That way I have a known base configuration from which to start modding. Are those available anywhere to download? Thanks!

Hello there. I have problems with connecting device with 1-wire protocol. Device: DHT11 Temperature-Humidity Sensor - It is Arduino version with pullup on the board. Board: Orange Pi Zero LTS (H2+) System: Linux orangepizero 5.10.21-sunxi #21.02.3 SMP Mon Mar 8 00:28:04 UTC 2021 armv7l armv7l armv7l GNU/Linux Based on instructions im preformed some steps: 1) Through armbian-config im enabled w1-gpio 2) Installed gpio app to get info about ports: +-----+-----+----------+------+--Orange Pi Zero--+------+----------+-----+-----+ | H2+ | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | H2+ | +-----+-----+------…

Hello, I have spent a lot of time, trying a lot of Armbian versions, looking on a lot of dedicated topics, building Armbian... and I still cannot display a desktop on the 3.5" gpio lcd (XPT2046) So, I post this topic for anybody can or would like to help me please... Olivier

I have a NanoPi Neo Core and I'd like to analyse the SPI controller driver and why it toggles the lines the way it does. In the overlay file, all I see are mentions to 'spidev'. Where can I find out why the data lines shown below toggle the way they do? I.e. chip select goes low way before the clock line. The MISO line has a droop to GND briefly and the CLK line hangs high for a while before toggling... Thanks forum :). YELLOW: CS PURPLE: MOSI BLUE: MISO GREEN: CLK EDIT: I'm sending two bytes, 0xDA, 0x00 at spi mode 3. Ignore the decoder, it was set to read LSB first.

Hi all, I'm working with a BPI-P2 board. I installed the last Armbian version for BPI-M2 as the two boards are basically the same except the RJ45 connector and the eMMC. I installed it on an SD card, and everythig worked perfectly. Now I need to put the OS on the eMMC and then completely remove the SD card, but I'm struggling. The default Armbian for BPI-M2 is not intended to support eMMC, so I'm not surprised that with this version the eMMC dosn't show up. So I tried to modify the dtb and enable the eMMC nodes, and then reboot. Here the changes I made: mmc@1c10000 { reg = < 0x1c10…

Hi everybody! I am new to this community and I am trying to find out if anyone here with a NanoPi Neo Air board got bluetooth working on Armbian Buster (mainline based kernel 5.10.y). Here is the armbianmonitor -u log http://ix.io/2UKF For about one week I am trying to make bluetooth work and with no result. I tried also Armbian Focal (mainline based kernel 5.10.y) and the results are the same. Bluetooht not working/recognized. I mention that I enabled BT support from armbian-config. dmesg | grep blue empty result rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no The images were compile…

hi new armbian user here.. ive recently got a pcduino v3b and the old OSs for it suck, cant update anything or find what i need... ive tryed downloading a few builds of armbian for pcduino, but im having some issues, firstly hdmi doesnt boot, i mean, never get anything on screen, the only access i have is via the serial port ive just grabbed the latest build that says the board is supported, but i cannot get a network connection, ethernet is plugged an 'up" but no ip or connection, and it seems the onboard wifi cant be found either.... also receiving error messages about failing to reset the ethernet dma ... Starting kernel ... [ 28.028075] sun7…

I found that it is not easy to use the Dallas one-wire temperature sensors and the composite TV-Out on the Banana Pi with the current Armbian version. I have searched for posts on these topics in the forum. The posts that I have found in this forum describe solutions for outdated Armbian versions or do not give enough detail. The following posts in this thread will describe how to solve these problems for the current Armbian version for the Banana Pi M1.

Hello Community, I have a (hopefully) quick question about the SATA port on my Bananapi. I wanted to attach a msata card via adapter to my Bananapi, like I already do on my Cubietruck. However when I start look for the msata drive it does not show up. However when I double check the drive via a USB SATA adapter the drive does show up. Could someone please tell me what is going ? Thx, blub4747

Hi, As you can see in the armbianmonitor output, an error prevents from using the Spi with the Orange pi Zero board using a newly downloaded Armbian image. The output refers to the Armbian-Hirsute image (the last one tested) but the same error also occurs with the Buster and Focal images. Unfortunately I don't have the knowledge to correct the following error myself: [3.349869] sun6i-spi 1c68000.spi: chipselect 0 already in use [3.349901] spi_master spi0: spi_device register error / soc / spi @ 1c68000 / flash @ 0 [3.349953] spi_master spi0: Failed to create SPI device for / soc / spi @ 1c68000 / flash @ 0 The only commands exe…

Hi there. I use Orange Pi zero as home print server. It works for few months for now and I am very pleased with that. Although, my printer falls into deep sleep after printing (it's Brother HL-1110EW) and cannot be woken up by the server. I have to start printer manually to print next printouts. Thus I wanted to install tea4cups to drive a relay turning the printer on and off when needed. I installed the WiringOP-zero (from here: https://github.com/xpertsavenue/WiringOP-Zero) but then strange things become to happen. I connected temporarily a LED diode to indicate the changes of the GPIO. (GPIO-7 and GND). The LED is on all the time, no matter what command I se…

Hello, After i made the Focal update i2c is very slow and armbian-config does not start. So I made a fresh installation with Armbian Focal mainline based kernel 5.10.y But no I have the same problem. What could be the reason? Is it possible too test the i2c bus? thx greetings

I'm trying to load Armbian on my NanoPi R1, but it doesn't boot. I've been able to boot it successfully with https://www.friendlyarm.com/ official image, and also various (unsupported) DietPi images. I tried Armbian_21.02.3_Nanopi-r1_focal_current_5.10.21.img.xz using Balena Etcher to copy it to the SDCard on a Macbook laptop. Instead of seeing the uboot startup, the terminal remains completely empty. No idea where to start on debugging this. Please help! Thanks!

So, here is the problem: I'm running the latest version of Armbian buster on an Orange PI PC+2E and as you know this piece of crap doesn't even support a proper shutdown function: all what is does is "reboot: system halted" and the screen remains on. Is there a way to turn the screen off (at least) after system halted? maybe a script that runs right before shutdown ? I've reas several discussion but non of the solutions worked

Hi, Nano pi duo 2 module I2C is not working in kernal Armbian Focal 5.10.21. I have camera OV5640 attached to Nano PI duo 2 via I2C 2 I found my I2C2 is disable how can I enable? root@nanopiduo2:~# fdtget /boot/dtb/sun8i-h3-nanopi-duo2.dtb /soc/i2c@1c2b400 status disabled I found I2C 2 which is connect to camera is not working root@nanopiduo2:~# ls -l /sys/class/i2c-adapter/ total 0 the I2C detect command and sometimes armbianmonitor does not genetrate the link, root@nanopiduo2:~# i2cdetect -y 0 Error: Could not open file `/dev/i2c-0' or `/dev/i2c/0': No such file or directory root@nanopiduo2:~# i2cdetect -y 1 Error: Could n…

Hi, I am having a hard time getting Armbian to boot on my Cubietruck. I have recorded some serial output but it does not show anything helpfull (at least for me). It just stopps at "Starting kernel". Verbosity is set to 7. Serial output 21.02.3 https://pastebin.com/DMWRzTgn Serial output 21.02.1 https://pastebin.com/a9Hasywc I tried the same SD-card and power supply with Arch for ARM. Arch boots fine. Serial output Arch Linux: https://pastebin.com/bMPf3gfx What further options do I have to debug this? As I am not really familiar with Arch I'd rather run a Debian / Ubuntu based OS. Best regards, Albert

Hello, bit of a strange one here. Using Armbian 21.02.3 Bionic with Linux 5.10.21-sunxi on a NanoPi Neo Core. Using nmtui to set a static IP on the Ethernet interface and all is good. On reboot, a second interface is added (dhcp) and the static interface disabled. Any help at keeping a static IP that survives a restart would be very much appreciated, Cheers Rob

After flashing the last release (21.02.3) of Buster for Orange Pi One Plus H6 I discovered that no sound card was available. aplay - l gave: Then flashing a one year old version (20.02.1) the hdmi audio was available. But after making the updates, apt-get update , apt-get upgrade and enabling the Desktop aplay -l gives : no soundcard found. Please Help Regards https://www.fiatb.fr

Hi, i'am desperate with my banana-p1 M1. It is (still) running nicely with an old 'Lemaker' Lubuntu version. But its an old linux version and the are 'iceweasel' issues in combination with https. So, it's a good time to use a (much) newer version of linux. I've tried several versions/downloads of Armbian: debian, ubuntu. I've tried different (tested with F3write/read) SD cards. Used several methods to 'write' the SD-card(s), like 'dd' or the etcher-tool.... ALL results have the same problem. (i've got an picture of the screen, but i can't upload it to this forum???) In sort, it say's: U-boot 2020.10-armbian ..... Allwinner Tech... CPU: Allwinner A20 (SUN7I)…

I have a NanoPi Neo and I'm currently looking to find out if the I2S pins can be set up as basic GPIOs? I can't find their names, (i.e. PA17) so not sure where to even begin with regards to tinkering the kernel. Any help appreciated! http://wiki.friendlyarm.com/wiki/images/c/c4/NEO_pinout-02.jpg

Hello everyone! You need to run an orange from battery power. I achieved by lowering the frequency of the current to 160mA. But I can't turn off the GPU. since I don't need it and ethernet. uname -a Linux orangepione 5.9.14-sunxi #20.11.3 SMP Fri Dec 11 20:31:12 CET 2020 armv7l GNU/Linux root@orangepione:~# I installed the h3consumption utility, but it does not output information to the console. root@orangepione:~# h3consumption -p root@orangepione:~# from teams root@orangepione:~# h3consumption -g and root@orangepione:~# h3consumption -g off change but no current. I think the core is very new. I don’t know which way to go,…

Hi I am using an OrangePi Zero 2+ with AllWinner H3 and i need both uart. I enable them with armbian-config and on pins Uart2 on pins 8 and 10 work fine bat uart1 on pins 11, 13 don't. The pin on this board is not the same as orangepi zero? I mast make some setup to make uart1 to work? auto@orangepizeroplus2-h3:~$ uname -a Linux orangepizeroplus2-h3 5.9.14-sunxi #20.11.3 SMP Fri Dec 11 20:31:12 CET 2020 armv7l armv7l armv7l GNU/Linux auto@orangepizeroplus2-h3:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=i2c1 uart1 uart2 uart3 usbhost2 usbhost3 …

Hello After a couple of years, I took my "ancient" OrangePi board and found it working well with Ubuntu 18.04 (kernel 3.14.113). And I even did distr update to 20.04. So HW is ok. I found that Armibian support status of OrangiPi is changed to "Supported" and decided to try the latest image with modern kernel "Armbian_21.02.1_Bananapi_focal_current_5.10.12_desktop.img.xz" (shared image between OrangePi and BananaPi). XFCE desktop was loaded but USB was not working. And that was the known mismatch between OrangePi and BananaPi HW conguration. So I updated "/boot/armbianEnv.txt" with "fdtfile=sun7i-a20-orangepi.dtb". But after that video became OFF…

Linux orangepilite2 5.9.8-sunxi64 #ifb SMP Fri Nov 20 20:38:13 EST 2020 aarch64 aarch64 aarch64 GNU/Linux After trying to load batman-adv module i get the error Segmentation fault. This is the dmesg output of the error that occurs: [ 952.114742] Unable to handle kernel paging request at virtual address ffff800026beb000 [ 952.122734] Mem abort info: [ 952.125603] ESR = 0x96000006 [ 952.128674] EC = 0x25: DABT (current EL), IL = 32 bits [ 952.134042] SET = 0, FnV = 0 [ 952.137123] EA = 0, S1PTW = 0 …

Just yesterday I connected a 120GB Sata and transfered root using armbian-config to sata drive. After 1st boot the system was working. But when I did a shutdown and rebooted the Bananapi it stops booting. I cannot use. Help me restore the root back to SDCard.

I've been using the Armbian R1 image (Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.7z) on the NanoPi R1S with good success. In particular, the USB host port worked perfectly, with no changes required. I thought it was probably about time to upgrade to a newer kernel, so I downloaded Armbian_21.02.1_Nanopi-r1_focal_current_5.10.12.img, flashed it to an SD card, and booted. However, plugging in an external USB device results in absolutely zero shoing up in `dmesg -w`. I tried a USB-UART (STM32-based ACM), USB3 hub, USB 3 Mass Storage (Kingston 16GB), and a Playstation 3 Eye, without any entries in dmesg. To do some debugging, I also downloaded Arm…

Hi guys I have an OPi1 with armbian 5.83 kernel 4.19 and I can't use otg. It seems powered but it doesn't recognize anything. I read this topic but I can't understand what to do. I just want to attach an external storage or a wifi dongle, to avoid using an usb hub. So I think I shoud use the otg as host for what I understood, right? thank you in advance for any help

Hi, trying to install a char driver without any driver framework. The only thing I can not install is getting the Interrupt through to the interrupt servce routine err = request_irq(irq, handler, // IRQF_TRIGGER_RISING, IRQF_TRIGGER_HIGH, "can4linux", &can_minors[minor]); irq is the Interrupt number of the CAN controller, it is fixed in the A20 to 58. I do get no error messages, but the isr is not called. What I am missing? Greetings Heinz By the way, it worked an Bananian 3.x