Tinkerboard

When connecting to the built-in wifi adapter (wlan0) on the tinkerboard S (rockchip 3288), the kernel produces a stacktrace and clients can't connect. [ 839.074341] kernel BUG at mm/slub.c:3904! [ 839.078825] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM - (see http://ix.io/1J1n) Is there a fix for this?

We are looking at replacing the raspi3b+ with the tinkerboardS (rockchip 3288) in an embedded system, running armbian (bionic-4.19). Initial tests show that OS stability, board performance and form factor make the tinkerboardS a good substitute for the raspi. However, one issue we have run into is a conflict with pin 32 of the GPIO which is used by the hostboard for managing output devices. We have tried to turn off serial2 by removing the UART2 overlay and adding 'console=display' in /boot/armbianEnv.txt and also disabling & masking serial-getty@ttyS2.service but that hasn't stopped pin 32 from being chatty when connected to the hostboard. Is…

Hi, I'm running Armbian Stretch on a Tinker Board and trying to use a one-wire thermometer. I have this in /boot/armbianEnv.txt: overlays=i2c1 i2c4 spi2 spidev2 uart1 uart2 w1-gpio However, when I boot the board, I see this in dmesg: [Wed May 8 17:38:43 2019] rockchip-pinctrl pinctrl: unable to find group for node w1_pins [Wed May 8 17:38:43 2019] w1-gpio: probe of onewire@0 failed with error -22 Kernel version is Linux tinkerboard 4.19.33-rockchip #5.77 SMP PREEMPT Wed Apr 3 17:06:29 CEST 2019 armv7l GNU/Linux Any ideas? I'm using the rockchip-w1-gpio.dtbo that was installed with the system. Regards, Dianne.

Dear All, I am running a project with Tinkerboard and a gigE camera. Trying to take video image through gstreamer (gst-launch). The camera is an Imaging source camera (DFK 33GX249) and I am using the linux library (https://github.com/TheImagingSource/tiscamera) for developing apps. My Tinkerboard is running Armbian Stretch (Armbian_5.50_Tinkerboard_Debian_stretch_next_4.14.52_desktop) Everything is working perfectly untill I am trying to run the command below: tinker@tinkerboard:~$ TCAM_LOG=DEBUG gst-launch-1.0 --gst-debug=tcamsrc:5,tcambin:5 --gst-debug-no-color tcambin ! videoconvert ! autovideosink The output is: Spoiler …

I try to understand the usage of Tinkerboard for Industrial Application usage, we have below questions. 1. Operating temperature is between 0-60 C [as many Industrial PLCs recommend 0-55 C only] 2. Long Term Supply of the Boards 3. Bulk Quantities buying [Get 30 to 50 boards in 2-4 weeks notice] The board and quality seems top notice, RPI interface is good for our use cases, anyone sees a risk in above points or would like to suggest something? We are looking a good sized community, Ubuntu OS, much stable and better performing board compared to Raspberry PI, all seems good with Tinkerboard. Please share your idea…

I'm using Armbian on a Tinker Board S. I did the installation back when the 4.4 kernel was still the default one. I expected that I'd get the newer 4.19 kernel by using 'apt update && apt dist-upgrade' at some point as it would become the new stable. This does not seem to be the case however, as I see the new downloads use 4.19 by default, but the stable package still points to a 4.4 kernel. Is it recommended to just move up by installing the kernel package with the next suffix or are there still reasons to wait with upgrading?

Just reporting that there is some tx-offload bug in the ASUS Tinker Board Rockchip. I think I read about this issue regarding other rockchip/platforms when checksum offload bugs on large packets. When I run ethtool -K eth0 tx off I stop having issues with NFS over TCP The last part of diagnosis is when I forced a NFS crash by enabling tx offloading.

Looking for a current realtime RTOS real time deb package or SD card image for the tinkerboard. I have been trying to compile a current real time build. All of my attempts have failed so far. free offer described below

Hello Guys. สมัครสมาชิกufabet เว็บพนันบอลต่างประเทศ I want to extend the current kernel (Tinkerboard with rockchip-kernel-4.4.120 on Debian-Armbian) to include IR (GPIO) and DVB modules. What do I have to consider or is this possible with the usual run-through? (copy .config from current system, make menuconfig, make, sudo make install, sudo make modules_install) Is there possibly already a tutorial that I have not seen?

Hi! I connect my 1366x768 monitor to Tinkerboard, but resolution sets to 1280x720. $ xrandr Screen 0: minimum 320 x 200, current 1280 x 720, maximum 8192 x 8192 HDMI-1 connected 1280x720+0+0 (normal left inverted right x axis y axis) 410mm x 230mm 1920x1080 60.00 + 1280x720 60.00* 720x480 60.00 Yes, i tried set timings manualy. I set native from edid: Modeline "Mode 0" 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync But after applying this modeline: - monitor detects 1280x720 resolution instead of 1366x768 - crops image as 1024x768 - have many noises and waves on screen... very unstable image (pixel clock 8…

Hello, I have several Hardware working with the Tinkerboard / S and like to propose those to the "Tested 3rd party hardware" section To whom can i address this? Thanks Roman

Hey, maybe a stupid question, but how I can change the i2c clock rate in the armbianENV.txt? I have search around the forum and didn't find anything. can someone point me in right direction? Greets

Hi I have a problem with change desktop language from en to polish. I tryed all solutions armbian-config , dpkg-reconfigure locales, export LANG. After reboot I got english desktop and locale info http://ecocut.pl/wp-content/uploads/2019/03/locale-1.jpg

Hi, I'm trying to upgrade my armbian from 5.73 to 5.75 but without succes. I've checked in armbian-config if the updates are not frozen which is not the case. I tried : - sudo apt-get update sudo apt-get upgrade - sudo apt update - armbian config -> system - > firmware (update) I did accidentally installed Full firmware package but reverted to mini. kernel version should be ok : ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.19.20-rockchip And I'm not sure what else I can do to upgrade to 5.75... I would like to use the new drivers for the CPU so htop shows more info. Th…

Hello Currently my SixFab 4G hat is not working with the 4.4.x Kernel but with the latest 4.19.y Is there any chance that you port media script to the new Kernel build? Many Thanks Roman

Hello ! I bought this screen recently: https://www.seeedstudio.com/10-1-inch-1200-1980-HDMI-IPS-LCD-Display-p-2863.html I tried to connect it to my Tinkerboard but could not get an image. On an raspberry I have input specific display settings in the configuration file. hdmi_drive=2 hdmi_mode=87 disable_overscan=1 # 10.1 inch hdmi_timings=1200 0 100 24 52 1920 0 65 4 25 0 0 0 60 0 169000000 0 max_framebuffer_width=1920 max_framebuffer_height=1920 display_rotate=3 framebuffer_width=1920 framebuffer_height=1200 By cons I do not know how to do with the tinkerboard. same problem on Nanopi-M4

Hy again :p; I have customed my sd for my tinkerboard. i have done some settings like eth0 in static, partitions modified scripts and hostapd. When i put it in another Tinkerboard, everything works except wifi ap. I have searched why, and i have found that in my initial tinkerboard wifi is wlan0 and his settings is in /etc/network/interfaces.d/armbian.ap.nat When i put my SD in another tinkerboard, it is wlan1 which mounts and no wlan0. Wlan1 has no ip address. i don't see where is the problem? thanks by advance

Hy, I'm looking for a Command to get the Serial Number of my Tinkerboard. I have found this in the Web : cat /proc/cpuinfo | grep Serial | sed s/.*\ //g But i get 000000000000. Someone have an Idea please? Thank you :)

Hy, I have tried to use my tinkerboard like an hotspot. configuration done with armbian-config. when i used the armbian jessie ( ARMBIAN 5.73 stable Debian GNU/Linux 8 (jessie) 4.19.20-rockchip) : everything works IF i don't do an apt-upgrade. If i do an apt-upgrade or using the last img of armbian strectch, i cannot connect any devices to my Tinkerboard : here what i have when i used ssh to see what's wrong : Spoiler root@tinkerboard:~# Message from syslogd@localhost at Feb 20 01:22:35 ... kernel:[ 42.906202] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM Message from syslogd@localhost at Feb 20 01:22:35 ...…

Is there a status page like http://linux-sunxi.org/Linux_mainlining_effort , but for Rockchip? (I suspect there's not. )

Hi, I really like the new option to use DT Overlays on the tinkerboard. But right now I'm struggeling a little with it: I have an old installation with 5.60 which I updated to 5.70 via apt. But the /boot/boot.cmd is still the old one and the Overlays are not working. Maybe I'm blind, but I do not see, how to update u-boot and the boot.cmd as part of it via armbian-config. Can someone point me to the right direction? Thanks, Alex

hi i can not get my ethernet to work with img Armbian_5.72_Tinkerboard_Debian_stretch_next_4.19.16_desktop me lost !

Hello, Has anyone managed to get usb-redirector working? 4.14.70-rockchip and headers. with 'arm' It installs ok, and the driver loads... lsmod and dmesg confirms. Module Size Used by tusbd 126976 0 but when I try one the binaries, it just returns me back to the prompt.??? (i've tried other versions arm-eabi. armeb, that just returns file not found when using a binary) Many thanks. Mark

There's a few problems with the UART driver on 5.0-rc2 kernels, since proper checks are not done correctly and lead to a Null Pointer dereference. Here's a patch to avoid this issue : From 7e43ae8446b420907f00b43308ad0b99b6fe4e51 Mon Sep 17 00:00:00 2001 From: "Miouyouyou (Myy)" <myy@miouyouyou.fr> Date: Wed, 16 Jan 2019 23:58:52 +0100 Subject: [PATCH] drivers: tty: serial: Bail out if no UART is detected Before the 5.0, serial8250_register_8250_port consisted of one BIG if(uart && uart->port.type != PORT_8250_CIR) block, which prevented NULL dereference if uart, a pointer to an "uart_8250_port" detected through "serial8250_find_ma…

Tinkerboard (old one, not S) to be used as x2go thin client. Installed latest image (5.70_Tinkerboard_Ubuntu_bionic_next_4.19.14_desktop), applied all updates. Working fine (thanks to everybody who contributed). Issue remaining: My Tinkerboard refuses to use the monitor's native display size of 1920x1200, tried several monitors and cables (HDMI to DVI adapter cables, in case this is relevant). Without any modifications, Armbian desktop comes up with 1280x960. I used xrandr to set 1920x1080 (works), but 1920x1200 leads to "xrandr: Configure crtc 0 failed". Any chance to resolve this?

Which Os does support hardware encode h264\h265 ? Or where i can read about status supporting hardware encoding for video (h264\265) and image (jpeg) ? chip: RK3288

I bought a Tinkerboard S and Tinker Aluminum case yesterday, but because of the case, it's Wifi function is almost non-exist, so I bought a TP-LINK TL-WN722N v2 two hours ago. I was hoping to get a V1, which has a lot of information on Wikidevi, and looks like it's going to work out-of-the-box, but I got a v2, and now I'm trying to get it to work. Wikidevi provided a link to driver repository, I downloaded main branch and type "make all" in terminal, it says /lib/modules/4.4.166-rockchip/build does not exist. I tried to search how to install kernel header and tried this command "sudo apt-get install linux-headers-$(uname -r)", it doesn't work/help. …

Hi all, first post here so please forgive me if I've get any bits wrong. Thanks for all the work put into supporting this project, and thanks in advance for any and all considerations extended in helping me step through my issue here. so i've had an 8 node kubernetes cluster running fairly smoothly on my tb's for nearly a full year now, so far I have not had any major issues with armbian updates until this weekends... I did a round of updates to my cluster and, after rebooting all 3 of my model S tinkerboards seem bricked (redlight only, no output to HDMI).. The remaining five orig TB models with Samsung EVO SD's all came up without issue... s…

Running Armbian Desktop stable 4.14y my Tinkerboard sees the WiFi network but refuses to connect. It has worked with TinkerOS so I don’t think it’s hardware related and Iknow the passcode and WPA settings look right. When I try to connect it spins and then fails after timing out. armbianmonitor -u output (with ethernet attached) http://ix.io/1x1J I’m probably just missing something stupid. Suggestions?

Hi Igor and all, back after a long absence, Have been using Cubie2s since 2015, rock solid with Armbian. I've now moved as cubies don't support gigabit, and the Pi gigabit interface is limited. So I now have a tinkerboard and popped Stretch mainline kernel 4.14.y onto an SDcard. Linux tinkerboard 4.14.67-rockchip #88 SMP PREEMPT Wed Aug 29 15:07:29 CEST 2018 armv7l GNU/Linux I want to compile the faithfull usb-redirector against the headers, but sudo apt-get install linux-headers-`uname -r` results in not found. Bit of noob question, but I've trawlled around, but can't seem to find source/headers or should I move to a diffrent version? Mark

I wanna use tinker board to work with logitech c930e camera. when i use cheese to open camera in tinker board. it's just show one black picture, and the camera light is on. before i had use the nanopi m4 to work with the logitech c930e. it's working good. and m4 create /dev/video0 , /dev/video1. but tinker board just create /dev/video0, so i think it maybe inside kernel have some option not open. but i don't know which need open. i'm not good at kernel. can give me some help? thanks a lot

Topic to discuss RK3288 overlays, primarily concerning ASUS Tinker Board, the MiQi is technically EOL and has very little GPIO anyway, and TV boxes are more or less sealed. Kernel 4.19 will be the pilot for this, the discussion now that it seems to be working thanks to @martinayotte and @zador.blood.stained's feedback and examples is what to overlay. For testing/debugging I started with some ASUS overlays for RTC and 1wire. Easy ones: spidev out of the default tree but as default overlays. instead of making 1 overlay and messing with parameters, just make 2 overlays DAC's: I don't have a lot of hardware to play with, but @…

I just recently bought a sim5320a GSM/GPS cape for my Tinkerboard S and it requires the use of ttyS3; however, by default Armbian uses this port for console... so I'm unable to use it w/ the cape. What do I need to do to disable the console on this port to free it up? EDIT: Nvm... after reading more, this isn't my issue (although I did find the answer above, which is to edit the /boot/armbianEnv.txt file). It's (the GSM cape) connected to the GPIO, and I need to enable the UART serial on here. Posted below is the product I'm using, and the last picture shows the GPIO PIN mappings that it uses. https://vietnamese.alibaba.com/product-detail/sim5320a-5-9v-2a-3g-gsm-g…

I put a TinkerBoard in a Pi-Top CEED and using TinkerOS 2.0.8 it boots and the LCD works fine. Using Armbian it looks like it boots but nothing is displayed on the LCD. The Pi-Top CEED uses a HDMI to 30-pin converter board and the current LCD is a 1920x1080 14in that I used to upgrade the original. Any ideas why the Raspberry running Raspbian and The Tinkerboard running TinkerOS would work with the display but Armbian wouldn’t?

Hi everyone! Someone has implemented support for mcp2515 for tinker board in armbian? Thank you!

Hello everyone, I'm using the latest Armbian version on Tinker board. I notice that if I dont use for a few minute then my monitor will go blank and I need to press any keyboard or mouse click to make a monitor works again. Is there a way to turn off that functionality ? I would like to keep my monitor on all the time. Thank you

Linux 4.4.163 has been released since the 10th of November, but the builds on the 13th and 15th are still only showing 4.4.162. I use your builds because they're awesome, they get me the latest patches. I hope 4.4.163 is included soon

I have the same issue on my Tinkerboard, here's the armbianmonitor -U output: https://paste.ubuntu.com/p/jggvYDMbCX/

Hi, I am trying to make the RPI camera ( OV7750 ) to work with the TInkerboard in Armbian. But there is no module in /lib/modules for this camera. Is it already compiled in the kernel? Currently it doesn't work.

I had use QML to made some soft, and when i move those soft to Tinkerboard, it's Incredibly slowly... have any idea to fix this? did tinkerboard had open gpu acceleration? do i must change back to use QtWidget?

Hi there, I have set up a tinkerboard S and I'm loving armbian so far. I only just encountered a weird problem. When i try to code in spyder3 there seems to be a messup in the keys i press and the key that is produced in spyder3. The funny thing is that this only occurs in spyder. When I type in terminal or gummi everything works fine. I am connecting to my TB using vnc using X. I've googled a bit around and found this could be a error of the XKEYBOARD as written here (I am however still not sure): https://github.com/spyder-ide/spyder/issues/3713 However I cant apply the proposed solution. I've found i need to go to /etc/X11/xorg.c…

hello. I have a problem for quite some time on my tinkerboard. I do not know if it's a software or hardware problem. It appeared after connecting a special Raspberry USB Hub http://www.uugear.com/product/7-port-usb-hub-for-raspberry-pi/ I used this HUB on a raspberry 3b but he grilled the wifi chip (disappeared totally). I thought I had to grill the wifi chip of the tinkerbard like the raspberry but I can see the chip turn on from time to time. Today she has reappeared but "wlan0 not ready" in the network manager. sudo ip link show wlan0 wlan0: <BROADCAST, MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000…

Hello and thanks for reading. I have done some digging before posting this so let me explain my issue and then what I have tried. I am using the Tinker Board S (via SD card, had same issue using EMMC img also) with the Bionic mainline kernel 4.14.y (in armbian config tool it shows Armbian 5.60 Stable ) on an LG 24LF452B montior/tv with the boards HDMI port and no adapters. I have been trying to set the display resolution to 1366X768 or as close to it (it does not appear in the display settings menu natively) but cant seem to make this work. The display works fine on other resolutions, except for horrible image because the wrong resolution, and can be used on 1366X768 …

Hello, I'm observing a strange behavior. If I connect the Tinkerboard to HDMI, it won't start. Only the red led LED lights up. Yellow and green did not light up. The Tinkerboard ist connected to a NorthPada 5V 3A Micro USB Charger power supply. I measured the supply voltage with 5.3V and checked with an oscilloscope if there are voltage dips. But the voltage was stable. I did a cross test. I unplugged the HDMI cable and started the Tinkerboard. The Tinkerboard starts and the yellow and green LEDs lights up. I measured the supply voltage with 5.3V and checked with an oscilloscope if there a voltage dips. The voltage was stable and dropped to roughly 5.1V for a short ti…

Hello, I'm enabling g_ether driver on tinker board. The driver works and I'm able to emulate an Ethernet adapter on my PC when I connect it to the tinker micro USB port. This only works if the micro USB connection exists before powering ON the board. If I connect it while the device is already running nothing happens. This behavior may be related to the following kernel path: https://patchwork.kernel.org/patch/10535905/ Is there any parameter I can add to avoid the USB from going to hibernate state? Or would it be possible to add the mentioned patch to armbian build tool? Thanks!

hello i just installed Armbian_5.59_Tinkerboard_Ubuntu_bionic_next_4.14.67_desktop on a new tinkerboard s .. and ran myself into a corner immediately. i was trying to figure out how to get 4K 2160p resolution instead of HD 1080p. i changed the refresh rate from 60Hz to 30Hz and now can't get the display back. i tried reboot. and documentation at https://docs.armbian.com/User-Guide_Fine-Tuning/ said to modify /boot/boot.cmd and that file says "edit /boot/armbianEnv.txt to set supported parameters" .. . so i set disp.screen0_output_mode=1920x1080p60 in armbianEnv.txt no luck .. i seem to have gone headless earlier than planned .. advice pls? i w…

I've adapted a set of patches from Urja Rannikko, which move the HDMI frequencies definition into the DTS file, with some preconfigured rates if none are defined in the DTS. The original patches set is here : https://www.spinics.net/lists/arm-kernel/msg673156.html The big patch I used as a basis is here : https://github.com/urjaman/arch-c201/blob/master/linux-c201/0020-RK3288-HDMI-clock-hacks-combined.patch I included these patches by splitting them again : https://github.com/Miouyouyou/RockMyy/commit/57ff073fffb5678e75959e566704376f6f52ac17 These patches were suggested to me here : https://github.com/Miouyouyou/RockMyy/issues/3 …

Referring the MPP samples, i have got an application which can give me NV12 data. 4 instance(or threads) of this application will give me raw data, i need to scale all of them in a single screen. Is it achievable through Mali GPU with current development of userland/kernel driver? Also i need to perform composition. On that tiled screen, i need to show other semi-opaque(transparent) window. Which library can help me to do the same?

I have 85 tinkers running with armbian 5.41 xenial next 4.14.23. Normally I run a script that apt upgrades them all but I run a small batch of them first as a test. Today I ran apt update/upgrade on three of them and they are all bricked. No output to the screen. Can't ping them. Any ideas?

Hi folks... Looking at RK3288 on Armbian and the power/thermals - which are considerable considering SBC's like tinkerboard and miqi Currently - looks like all cores are following the same power/time domain - so one core goes fast, and the others follow, so sucks power and raises temps, and we get heat soaked quickly... Looking at the Rockchip docs, it does look like the RK3288 does have PD's for each core along with other logic... Six separate power domains for every core to support internal power switch and externally turn on/off based on different application scenario * PD_A17_0: 1st Cortex-A17 + Neon + FPU + L1 I/D Cache * PD_A…

I have Rockchip 3288 board. As per the link: http://opensource.rock-chips.com/wiki_Graphics I checked the log at /var/log/Xorg.0.log and found glamor initialization failed. There is also log which says EGL_MESA_drm_image required, i checked x-server code and found this message lead to glamor initialization failed. Apart from these when i run glxinfo, it shows It means direct rendering is enabled. But when i run glxgears it consumed almost 18% CPU( So i think glxgear is not able to use GPU and performing all tasks at CPU). What i am to do: I have created a application which can decode H264 vid…

I am trying to get my Win TV Dual HD running at the Tinkerboard. But idk where the issue is Build my own Kernel ./compile.sh BOARD=tinkerboard BRANCH=dev KERNEL_ONLY=yes RELEASE=stretch ~# uname -a Linux tinkerboard 4.18.5-rockchip #3 SMP PREEMPT Sat Sep 1 12:50:32 CEST 2018 armv7l GNU/Linux ~# dmesg | grep em28xx [ 7.639731] em28xx 1-1.3:1.0: New device HCW dualHD @ 480 Mbps (2040:0265, interface 0, class 0) [ 7.639738] em28xx 1-1.3:1.0: DVB interface 0 found: isoc [ 7.702511] em28xx 1-1.3:1.0: chip ID is em2874 [ 8.835994] em28xx 1-1.3:1.0: write to i2c device at 0xa0 failed with unknown error (status=5) [ 8.836001] em28xx 1-1.3:1…

Using 5.41 with Chromium 68.0... Using <input type="file"> on a web page... If you click a usb camera (probably usb stick as well) and the system mounts the usb (assuming it wasn't mounted already by other means)... after you close the dialog (whether you selected a file or clicked cancel)... chromium is frozen.

Hello there. At present I power my Tinker Board S with a bench power supply set to 5.25V. The power supply has 10A current limiter. I measure the voltage at the GPIO pins using a 6.5 digit multimeter (in cal). The micro usb cord is 1.2 meters (4 feet). When the board is running in tinker os at idle, it is drawing 500mA, and i read 5.00V on the GPIO. But when I load the CPU using sysbench the current spikes to 1.6A, and the voltage measured on the GPIO drops to 4.45V. I measured that the micro USB cable is 0.37Ohm resistance, so about 0.55V of that power drop is due to the micro usb cable. That means all of the voltage drop is not due to the power c…

Hi , I have an ASUS Tinker board S and I installed Armbian 5.54 on SD card. Then, I want work on eMMC drive of ASUS Tinker board S but, Armbian no detect it. How can I work with eMMC drive in Armbian ? Here my board info: http://ix.io/1j2Z Thanks, see you.

Dear Colleagues! In the I2S RK3288 interface rather limited number of timeslots of TDM (PCM). I try to use RK3288 spi as the subordinate controller for input and processing of a data stream of TDM (128 timeslots). Was - whether you have a practice of creation of spi of the driver for operation in slave DMA?. Perhaps for other chip. I will be glad to responses! Thanks!

As https://www.armbian.com/tinkerboard/ has a quite fresh 4.14 Linux kernel (in Armbian Stretch Next Desktop 5.50) I am trying to use that instead of the standard TinkerOS 2.0.7 with a 4.4.103 kernel. However, Armbian is configured to provide only spidev2.0, while TinkerOS can have spidev0.0, spidev0.1, spidev2.0 and spidev2.1 all enabled at the same time as long as you disable UART4 which shares GPIO header pins with SPI0. In the TinkerOS case, there is a config tool which edits a small and straightforward text file in /boot/ containing lines such as "intf:spi0=on" or "intf:uart4=off". The corresponding Armbian file seems to be /boot/armbianEnv.txt - possibly…

today I flashed armbian in my Asus TB and WiFi was working but only for first boot now I am facing this problem ifconfig wlan0 up operation not permitted

Hi, I created a Tinkerboard OMV 4 image some while ago, we uploaded it untested (since 'OMV' just means Armbian's build system doing its job with a massive post processing script adding tons of stuff) but now got the report it doesn't boot. That's a bit surprising given that the image has been downloaded over a hundred times and no one complained so far. Deleting the image is the logical consequence but maybe someone here with a serial console can give it a try and report whether the board comes up or where it gets stuck at booting. http://kaiser-edv.de/tmp/jk4NM5/OMV_4_Tinkerboard.img.xz (with mainline kernel) or the default kernel variant from he…

Hello, I have 2 questions. 1. How long does the support for the tinkerboard takes. Because I'm using the Board as Server and i don't need much CPU Power but I don't like to buy every 2-4 years a new board because the support ended. The reason of this question is, the odroid c1, there is no stretch image for this board. 2. Is there a good howto, how to build a kernel on a thinkerboard with own config? Reason for this question is, I have installed the latest armbian stretch server image on my tinker board and the kernel has no ebtables support. Second Reason ist question 1, build a own Kernel and update to Debian 10,11, ...., n.

Hello, I am using the armbian kernel+uboot patchset of the rockchip-next (4.14.x) part to support Tinkerboard+TinkerboardS in an own home automation environment. U-Boot 2018.05 and kernel 4.14.53 are working fine so far with the current patchset published on GitHub (thanks for this great work!). However, the only issue I am still having is, that the ethernet port always comes up with "no-link" on the intial powerup of the Tinkerboard. As soon as I software reboot it after the initial powerup the ethernet port perfectly comes up with a link and I am able to setup all IP data, etc. But as soon as I completely power down the system and replug the power-cable it a…

Hello, I am the author of a home automation platform (RaspberryMatic) which is targeted for embedded platforms like RaspberryPi or Tinkerboard. I am regularly following Armbian kernel and u-boot updates for the Tinkerboard and integrate them into my buildroot-based environment so that recent kernel and u-boot versions can be used. I have already updated my environment to kernel 4.14.x and U-boot 2018.05 using the great armbian patchset from GitHub (Thanks for the hard work to get all the Tinkerboard S related issues sorted out recently). What I am currently trying to achieve is to get the Tinkerboard to use a different set of standard gpio settings…

Just got my Tinker Board S in... used Etcher to flash the following image to the eMMC: Armbian Stretch mainline kernel 4.14.y It won't boot. That same image flashed to the SD card boots just fine. I've tried using the armbian-config to install it to the eMMC that way; however, all I get are "There are no targets. Please check your drives." What the heck am I doin' wrong? New to the entire SBC realm, and got this instead of the Pi. I don't want a desktop distro installed... just a simple distro w/ bash. Any help would be appreciated... spent the last 6 hours trying to figure this out. This isn't the 'tinkering' I had in mind when I got this thing.…

I cannot get any CMA reserved space when I use latest LTS kernel (4.14): dmesg always says that no memory has been reserved for CMA. Is CMA working on mainline kernel for Mali Midgard? Is it required for 3D/video decoding stuff or the Mali kernel driver should instead allocate memory on-demand? I see that most of the kernel configuration options regarding CMA are disable or not set, which one requires to be enabled?

Hello! I set up a firewall on the Asus Tinkerboard. I came across a very strange thing - the lack of support for the CT target in iptables. In fact, it appears that iptables has support of given target, but the required kernel module is missing. After running cat /boot/config-4.4.120-rockchip | grep NETFILTER_XT_TARGET_ST I saw the following: # CONFIG_NETFILTER_XT_TARGET_CT is not set. What the reason of that decision? It blocks ability to forward sip, ftp and some other protocols precisely. And also blocks ability to use SYNPROXY target correctly. Is it planned to include this module in the build?

Today my effort is getting the rk3288 tv box boot from USB devices. During the initialization of the OTG USB port, u-boot complaints about dwc_otg_core_host_init() function which is timing out. I tried to manipulate the device tree chaning the dr_mode flag to host, otg and peripheral, but nothing changed. The only way to get rid of the timeout is to disable the device which, by the way, seems to not work anyway. U-Boot 2017.09 (Jun 17 2018 - 18:55:17 +0200) Model: XT-Q8L-V10-RK3288 DRAM: 2 GiB MMC: dwmmc@ff0c0000: 1, dwmmc@ff0f0000: 0 ** First descriptor is NOT a primary desc on 0:1 ** In: serial Out: serial Err: serial Model: XT-Q8L-V10-RK3288 …

Looking for a bit of advice... Been running Armbian CLI on the tinker (nonS) via SD card no problems Got an S with eMMC... Wrote tinkerOS and it loads no problems... Wrote Armbian image.... No go / boot Any suggestions on how to fix.... Thanks... There is a bit here which is what it used to re-write TinkerOS to the eMMC https://tinkerboarding.co.uk/wiki/index.php?title=Setup Really like the Armbian CLI versions as lightweight and without bloat.

Hello, after a short break, wants to continue with the Tinkerboard. :) I use Armbian-Stretch with the kernel-4.4.126. I want to connect an IR receiver to a GPIO port and use it with the lircd tool. What possibilities does Armbian-Stretch offer me here? Thank you very much. Clash

Anyone who typically updates on nightly kernels I would recommend freezing and not updating until we clear up some issues gifted us by some large amount of upstream changes that broke well, pretty much everything. I will update this thread as things get brought back to life. June 7th 2018: I've made a branch (rockchip-default) to work out the kinks. So far I have the board booting and Mali working again (with an initial error on load) , however there is no HDMI terminal, so initial boots would require a uart or SSH hdmi terminal is back thank you to Ntemis on github, I'd missed part of the conversation (I only have cell phone while at w…

Hi guys, sorry, on with my second issue with the Asus Tinker Board and installing a DS3231 Real Time Clock module. I've tried following any instructions on the internet for Tinker Board use and a couple for the Raspberry Pi, from recompiling the kernel through to trying to edit boot files. I just cannot get this thing working so I've now got myself a fresh install of Armbian Stretch 4.14 and ready to go again. Can anybody provide a step-by-step installation for the Tinker Board and this module (I've been told the DS1307 is the same kernel module but for the life of me I cannot find any modules/.ko's available in Armbian)? Ma…

Using 5.41 I ran armbian-config to install armbian on a tinker board s emmc. Install went ok but get nothing but a black screen on boot. Any ideas on what to do to get it going?

Hi all, I've got an application that runs from the terminal and with it failing to work on Tinker OS I've gone back to my default OS, Armbian, where it works faultless. However, everything worked great on my own 25" Philips monitor.... The Tinker Boards will be plugged into a number of 1440 x 900 60hz Samsung and LG HDMI monitors; the only screens available where I am. When using these screens I get a 2-3 pixel vertical purple line down the left of the screen and horrific 1 pixel high, long horizontal multi-coloured lines 'snowing' down the screen like old TV interference. The LG monitors consistently flicker on and off trying to change resolution.…

Is it possible to patch the device tree someway to enable HDMI output and having the console on the framebuffer for debugging in current non-development armbian version? Thanks

Hi, Got a Tinker Board and tried the 5.41 Xenial mainline 4.14.23 desktop -> https://www.armbian.com/tinkerboard/#kernels-archive Need to enable the I2S on 40pinheader connector for both playback & capture (192KHz/32bits) but I dont seem to find the info for this. Any help is valuable!

THE MEDIA SCRIPT IS DEPRECATED, IN FAVOR OF THE OFFICIAL LEGACY MULTIMEDIA FRAMEWORK. PLEASE REFER TO THIS TOPIC: The UN-official, UN-supported, UN-necessary, UN-popular, UN-precedented... RK3288 MEDIA TESTING SCRIPT [2.0: Bionic update] So here is the final release of the RK3288 media testing script. Basically, the script provides the following functionality: Installing all the libraries and system configurations necessary for GPU accelerated X desktop, Chromium WebGL, full VPU video play acceleration up to 4k@30 HEVC (the maximum supported by the SoC), and GLES 3.1 / OpenCL 1.2 support. Three video players suppor…

apt-get update / apt-get upgrad Armbian Xenial desktop mainline kernel 4.14, system failed to reboot and need a power reset to bring up. # uname -a Linux tinkerboard 4.14.34-rockchip #20 SMP PREEMPT Sun Apr 15 20:07:28 CEST 2018 armv7l armv7l armv7l GNU/Linux

So those of us working on getting Retro Pie working on the Tinkerboard have run into a road block. Perhaps someone here might have a clue on this? Current using these instructions to build Retro Pie using the legacy Armbian Debian (4.4) https://github.com/Tinkerpie/Armbian-Setup And for audio over HDMI you need to currently make a change in /usr/share/alsa/alsa.conf setting defaults.pcm.card to 1 When this script linked down below: https://github.com/Rydra/bgm-for-es The BGM script takes over all audio so for instance the audio in games does not work or any other audio such as audio from the video sna…

Please post complaints, as of my latest build I'm getting the link drops as well.

Hi, I've got several tinkerboards that I've reproduced this problem on. I'm using the tinkerboard to do network tests, this includes iperf3 traffic,dns querys (dig), https and http (echoping), and ping. All of these tests runs against IPv6 targets and IPv4 targets. These tests are scheduled to very frequently (every other minute or so). To begin with, all tests run fine.. I get good results (~1gbit throughput / low latency / no packet loss). However, after running the tests for 15-20min, suddenly all traffic will more or less stop working (80-90% packet loss). This is no matter what I'm pinging, can be the local router, some target on the…

I am trying to get a USB Serial adapter working on my Asus Tinkerboard running Armbian. if i lsusb i get: root@tinkerboard:~# lsusb Bus 001 Device 006: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port however no /dev/ttyUSB0 shows up. Is there an armbian kernel for the asus tinkerboard with usb serial support?

On the Tinker Board , I have tested a simple GPIO application using preinstalled wiringPi C library. I also ran the same application on Raspberry Pi using preinstalled wiringPi C library, but I noticed that the Tinkerboard GPIO speed is very slow. I wonder why this is the case. I would appreciate, if someone share opinion about it. I've added the C program and attached oscilloscope screen-display for GPIO port speed for both Tinker Board and Raspberry Pi. I tested Tinker Board with 2018-02-22-tinker-board-linaro-stretch-alip-v2.0.5 image. GPIO speed is about 158 Khz I tested Raspberry PI 3 Model B with 2018-03-13-raspbian-stretch image. GPIO speed is about 1.9…

I connected a tinker to a 4k tv and the highest resolution that armbian offers is 1920x1080. What could be the reason that 4k res is not offered? I'm using ARMBIAN 5.43.180417 nightly Ubuntu 16.04.4 LTS 4.14.34-rockchip.

Hi there Board, I have bought my Tinkerboard after some good research with my fellow techies at Red Hat and reading thoroughly that 19+pages Tinkerboard Thread. After crafting a super lean/mean kernel (kconfig at https://gist.github.com/rfrht/5f0fa113f12fbacf832e57ff4967785a ), I got a stable and lightweight kernel configuration. Things got a lot funnier when doing some compatibility tests with specific Asterisk versions, I was able to install and run cleanly a Raspi .DEB pkg. And that got me thinking. I have now JUST replaced the Raspberry Pi with the Tinkerboard. And guess what: It was a _inplace_ upgrade! Using the same u…

Anyone here playing with USB network adapters? I have a (noname) USB3 Gigabit ethernet adapter which seems capped at 250 Mbps. I know the Tinkerboard only has USB 2.0 (so a theoretical maximum of 480 Mbps), just trying to see if there are better parts out there I could try.

Hi there! o/ I have noticed something... Odd. This is not a show stopper here, but the TinkerBoard NIC leds stays off all the time (if no traffic) even with link. It does blink somewhat schizophrenically when there's traffic. The right NIC led is bi-color and sometimes blinks in yellow, sometimes blinks in green. For what is worth, running Kernel 4.4-120. Issue also happened in build -104, which was the original Armbian image that I have downloaded. I thought it was something with the port, cables but... Traffic flows just normally Is it... normal? :-) Have a great (tinkering) weekend!!!

i have upgraded armbian on tinkerboard asus form 5.35 to 5.38. And this changed cpu governor to conservative. I have changed it to performance. BUT previous max cpu speed was 1.80GHZ and now i have only 1.61.GHZ I have cooler with fan on my tinkerboard and iam not scared high cpu temperature. Hov to get back to the maximum 1.80 GHZ frequency ???? I cant add 180000MHZ via sudo nano /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies to each core permission denied. please help

Hello, I want to extend the current kernel (Tinkerboard with rockchip-kernel-4.4.120 on Debian-Armbian) to include IR (GPIO) and DVB modules. What do I have to consider or is this possible with the usual run-through? (copy .config from current system, make menuconfig, make, sudo make install, sudo make modules_install) Is there possibly already a tutorial that I have not seen? Clash

I played a bit with the SenseHAT from the RPi guys. Doesn't work fully but I get the first things working. What does run: Joystick 8x8 led matrix (partly, seems that there are some parts of the framebuffer not fully working) What doesn't run: all the sensors attached on the board What's missing: load it devicetree overlay (at the moment it's coded into the main dts) how-to what's needed to get it working on your tinker too I'll keep you updated.

I try to get working a tinkerboard on a battery. I can do that with S.USV or S.USV Mobile but i don't know the difference between them. I have a xl4015 (5Amp buck convecter) but I don't really understand how it's work (i have a lm2596 too). I have a 20AWG micro-usb too but i can power it too from gpio. So i search a quick way to get it work on a battery. I work and search on this since 5 week and i really need to get it work. Thx

Hello all. I'm doing some tests with the Tinker Board to see what's the best operating system for it for a new video. I'm using the Armbian Ubuntu Desktop legacy kernel. For this I do Blender and Kdenlive renders to see if there's a speed difference. But with both I've got the problem that it crashes the Tinker Board. Sometimes it's a hard crash and the whole system freezes, and sometimes Blender or Kdenlive just close themselfs but Armbian keeps working. I do not have this problem in Lubuntu. In TinekrOS Kdenlive totally doesn't work. It looks the same as an unstable overclock on a system. I've tried different psu's. I'm using the Tinker h…

Hy, I have a Tinkerboard with armbian ( debian jessie). When I put behind my fiber router, and i do a speed test i have : With iperf3 ==> download : 980M and upload : 240M with speedtest-cli ==> More or less Results. I wanted to conenct my Asus's card behind the ONT(Optical Termination Boxes) i can connect with pppoe or dhcp. And in pppoe or dhcp my speed test show this : With iperf3 ==> download : 110M and upload : 80M with speedtest-cli ==> More or less Results. I have tested with anorther Board, bananapi mé with Bananian and i have the same Results if I put behin…

Hello, I want to install libdrm from here https://github.com/rockchip-linux/libdrm-rockchip But there are already problems with autogen.sh. See below. Does anyone have a tip for armbian (Debian stretch) on how to install this library? The Clash Spoiler $ ./autogen.sh autoreconf: Entering directory `.' autoreconf: configure.ac: not using Gettext autoreconf: running: aclocal --force -I m4 ${ACLOCAL_FLAGS} autoreconf: configure.ac: tracing autoreconf: configure.ac: creating directory build-aux autoreconf: running: libtoolize --copy --force libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR,…

For some reason the default UART utilized by uboot is uart2 on the Tinker. I haven't messed with it, and left it alone, but vendor uses UART1, and UART2 has a conflict with PWM pins. I'm in favor of changing, if anyone objects or has a more interesting idea, please discuss.

Hi, i get a probleme with the actual uart acces config by default on Uart2 (pin 32, 33), because i need to use PWM pin (use to set motor speed with a L293D) and on the board only pin 32, 33 can be use with PWM. Now i am using 32 33 pin as PWM but if the cable on these pin is connected the board doesn't boot, maybe because the uarts of u-boot use these pin and the result of un connected cable to my setup = Critical fail. When i remove the cable on pin 32 the board boot. So i need to solve that because i don't want to disconnect this cable at each start and i want to use uarts with this setup. I need to change uart2 to uart1 or find a way to get PWM or a other pin option …

Hi all, Saw that via Slashdot. A RPI 3 b+ benchmark comparing against other SBCs and TinkerBoard. Check it out: https://www.phoronix.com/scan.php?page=article&item=raspberrypi-3-bplus Feeling great for buying one, after reading all 18 pages of the forum! Ah. A big shout THANK YOU to Igor, Tony, Kaiser and everyone else that helped build a working Armbian release to this SBC. -RF

Is there a way to upgrade from an earlier version to 5.41?

Hello. Has anyone had success with setting up the onboard wifi on the Tinkerboard without the network manager? I have tried using wpa_supplicant to connect but not having any success. Here is what (I know works on an Intel Compute Stick running Ubuntu 16.04) I've tried: wpa_passphrase SSID password >> /etc/wpa_supplicant.conf wpa_supplicant -i wlan0 -c/etc/wpa_supplicant.conf -D nl80211 -B dhclient wlan0 dhclient just keeps retrying and goes no where, I don't get an IP address I can connect to my network using the Network Manager no problems, just can't figure out a way to get it to work with the network manager disable…

Video demonstrating issues reconnecting to Wi-Fi please help

linux-xenial-root-next-tinkerboard 5.38 with 4.14.14 kernel installed. armbian's apt repository has only 5.38. but packaged rom file from dl.armbian.com is 5.41 with 4.14.23. (Armbian_5.41_Tinkerboard_Ubuntu_xenial_next_4.14.23_desktop.7z) How to upgrade on linux latest armbian? It need waiting?

hi , i am using the gpio library provided by asus tinker board to work with gpio on armbian os . i am having issue with running the python script without giving sudo cmd. is there any alternative to overcome giving sudo all the time while running gpio python script or any other alternate library to use with armbian python add_event_callback.py can't open /dev/mem and /dev/gpiomem wiringPiSetup: Unable to open /dev/mem and /dev/gpiomem: No such file or directory Segmentation fault