Allwinner sunxi

Hello friends! I Am using 3G modem(Huawei E171 connected by OTG cable) on my OPi One for internet, but one problem - modem after few days working freeze. Reboot don't help because not full power off on USB, and after reboot i don't see modem in /dev. Only after physical remove modem and install again it's initialized and work fine. Question: Can i power off USB from cli? # uname -a Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linu # lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 00…

Hello, I am still using my cubieboard1 for openhab2. A few days ago I installed the system on an USB stick, then I thought that the 32Gb SD card is the for nothing. And I am planing to replace the 32GB sd card with a 128MB sd card. but i am stuck in prepairing the smaller SD card. Could somene advice me how to do this change? Until now I just formated the small sd card into ext4 and copied the /boot from larger sd card, but didn"t booted. Help is much appreciated.

I first noticed this on my Orange Pi Zero. The latest Armbian releases (4.13.x) have some kind of gap between bytes when transmitting over SPI. I have an SPI performance test built into my SPI_LCD code: https://github.com/bitbank2/SPI_LCD If you run the demo program, it measures how many frames per second it can write to an SPI-connected LCD. On older Armbian builds with kernel version 3.x, it would usually get 27-33FPS on the H2/H3 boards. With the mainline kernel builds and running the same code, I'm seeing 9-17FPS (depending on the board). The H5 doesn't seem to be affected (I'm using an Orange Pi Zero +2 H5 for testing also). Anyone else seeing…

How do I get a desktop running on this (legacy)? It only outputs a shell on the video out Additionally, is the hw video decoder enabled? Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113

Hi, Just a quick question as Debian Stretch has been out for a while now: Will there be an official upgrade of ARMBIAN for the Cubietruck (Cubieboard 3) at some point or is there a simple doc on how to upgrade the distribution? I run ARMBIAN with the legacy kernel (3.4.113-sun7i). Everything required for the system boot is in the NAND while the root and /home partitions are on the sdd. Would it be possible to upgrade to Stretch just by replacing the version name in the sources.list file? If there won't be any automated ARMBIAN upgrades to Stretch for this device. Would you recommend using the official Debian distribution (and bo…

Hello all. Try as I might, I can't get HDMI sound on my OpiPC. orangepi@orangepipc:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 I originally had no asound.conf, but I made one: pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } Looking around, I see an unanswered question on this from '16. HDMI on the TV does work with a…

Hy everybody, I have a fiber connexion at home. for my work, i tried to connect my Bananapi to my ONT (Optical Network Termination). My provider, Orange use pppoe with the vlan 832 for Internet. So i have installed the Packages vlan,ppp,pppoe. In /etc/modules i have added 8021q. in /etc/network/interfaces : auto eth0 eth0.832 ppp0 iface eth0 inet manual iface eth0.832 inet manual iface ppp0 inet ppp provider ft_fibre I have created /etc/ppp/peers/ft_fibre like this : pty "/usr/sbin/pppoe -I eth0.832 -T 80 -m 1452" noipdefault hide-password lcp-echo-interval 20 lcp-echo-failure 3 connect /bin/true noauth …

Hi, I Installed jessie on Orangepi 2. I installed on emmc memory with documentation and all works fine. I just reboot may orangepi with root login and good password. The OS wan't give me a prompt, I just have: "Linux orangepipcplus 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv71" ... and no prompt, I wait, and I wait, but no prompt. I can switch to another another console with ALT+F2 (F3,F4..), but if i want to log on it I have the same issue: no prompt I can ping IP address of orangepi, but I have no answer of ssh server, I can't connect to this. Do you have any idea about this ? …

Is there some DT overlay to enable or some software to install to use the onboard bluetooth radio of the Orange Pi Zero Plus 2?

Hi guys, Quick question about the USB ports on the Cubietruck. Once I am done with the usual setup procedure (changing the root password and setup a user) system reboot. I sometimes end up in situations where I need to access the Cubietruck directly and not through ssh. In such situations I noticed that my usb keyboard and mouse do not respond at all, eventhough if these are the exact same ones hich I used to the 1first time setup. What could be the reason for this ? Thx,blub4747

In download section for X2 Beelink there is no image for Server stretch test as advertised on download page, only for desktop. Is it normal ? (tm)

Hi, it ist well known, that a SD-card can be destroyed when you power-off a Raspberry-Pi without a shutdown. Does the same issue exist with an Orange-Pi (One) ? I want to use an Orange-Pi One headless and without SSH/TTY, only some sensors and LEDs are attached. Tnx L

I bought an orange plate zero pi that I requested for a project. The issue is that I can not start the AP mode. I am making use of the hostapd and isc-dhcp-server packages, apparently everything is well configured, I am thinking that the problem is the chip driver of the wireless network. I put some relevant data, from now on thanks. root@orangepizero:~# /usr/sbin/hostapd /etc/hostapd/hostapd.conf Configuration file: /etc/hostapd/hostapd.conf nl80211: Could not configure driver mode nl80211: deinit ifname=wlan0 disabled_11b_rates=0 nl80211 driver initialization failed. wlan0: interface state UNINITIALIZED->DISABLED wlan0: AP-DISABLED …

I'm running the latest armbian on my Banana Pi M1 as a headless file/media server. My problem is that my Banana Pi would randomly stop working any time of the day. A day would not pass by without me having to reboot my server manually by pressing the reset button. There would still be network activity as the activity lights on the LAN keeps on flashing and it would still respond to my ping requests. I'd know it stopped working if I can't access the server's services anymore through its web ui (webmin, transmission, etc.) and to confirm this I'd try to SSH into it and it wouldn't connect. I tried creating a script where it would restart the LAN if it pinged the…

Hello, guys, has anyone ever faced issues with SPI controller on BananaPi M2 ? I am having a weird issue which is confirmed by at least 2 peripherals: Waveshare 3.5 LCD and NRF24 wireless chip. The data incoming from MISO is always shifted by 1 bit to the left. , i.e. reading STATUS register of NRF24 gives 0x1C instead of expected value 0xE. The same story with other registers. Saleae logic analyzer is always showing correct pictures !!! See attached image as an example of reading STATUS register from NRF24: master is sending 0x07 and receiving 0x0E (14). I have tweaked byte rate and other parameters - no result. I have finally tried to connect using…

Hello everyone, I'm having some trouble with i2c between orangepi zero and ina219. Here is i2cdetect -y 0 respons: " 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: 40 -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- --" I'm using https://github.com/chrisb2/pi_ina219 and also installed https://github.com/adafr…

Hi to everyone, I'm new at armbian forum, but following the project since some month. As far as I can tell all contributors make a great job to enable a stable debian based distribution to many as possible arm-based boards. Thanks a lot for this great job. I bought one of the first available Banana Pi M3-boards in Germany, because I wanted (and did it already very successfully) to set up a small server for email, music storage, mythtv-backend, read out my central heating.... Until now I use a stripped down image based on the provided Ubuntu 16.04 image from http://www.banana-pi.org/m3-download.html As you all know the "support" and further developmen…

Guys, please help. I installed one orange pi plus 2e and orange pi one in following way: first server image (legacy kernel) then kernel upgrade to mainline. Everything works just fine, except I do not receive kernel updates. If I understood well, kernel should be upgraded via apt dist-upgrade.. But nothing. On both this machines I've got same situation: Welcome to ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 4.11.5-sun8i igor@orangepione:~$ uname -a Linux orangepione 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l armv7l armv7l GNU/Linux in my apt sources I have: igor@orangepione:~$ grep -h ^deb /etc/apt/sources.…

Hi everybody, just downloaded Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113 and flashed. I can see "orangepizero" in network, also ip is pingable but ssh port is closed. Is it a known issue? Armbian_5.30_Orangepizero_Debian_jessie_default_3.4.113 from archive works fine. Thanks

Hi...Is support for using Mali GPU of Orangepi PC2 enabled for armbian? I'm trying to install the mesa-dri utilities and getting stuck in the libc-bin segmentation fault? Is it because of lack of support or something else? Also I'm getting issues of protobuf while compiling Opencv for Orangepi PC2. If anybody can help!!

Hi, I have Orange Pi Zero based on H2+ which is failed to boot Armbian_5.34_Orangepizero_Ubuntu_xenial_next_4.13.8.img Symptoms: Green power light is always on, red led next to it does not flash at all. Ethernet lights are off. I am using proper power supply and Sandisk A1 16Gb Class 10 micro sd-card. Connecting UART-USB adapter based on CP2102x to UART port next to Ethernet ports shows nothing. Exactly same setup, same hardware, no changes on connections/setup boots "Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113.img" image without any problems. UART works fine. Any ideas how I can help to test newer image?

Hi, System: A20Lime2-4gb with latest legacy image Linux lime2 3.4.113-sun7i #23 SMP PREEMPT Wed Jun 14 23:57:45 CEST 2017 armv7l armv7i armv7l GNU/Linux When I shutdown or restart, it throws me back to login screen and again loads desktop even if I don't enter id and password and then shutdown automatically within 10 secs . I want it to shutdown/restart without this login screen. I tried shutdown from terminal ' sudo shutdown -h now' , 'sudo poweroff' still giving login screen. How can solve this issue ? Thank you in advance

I put the log of the console... I can compile a linux 4.11 and ubuntu 16.04.3 server with the packet from ARMBIAN... thats greats... but i had to correct some files to compile OK!!! Ubuntu 16.04.3 LTS bananapim2ultra ttyS0 bananapim2ultra login: root Password: Last login: Mon Nov 13 20:47:13 UTC 2017 on ttyS0 ____ ____ _ __ __ ____ _ _ _ _ | __ ) __ _ _ __ __ _ _ __ __ _ | _ \(_) | \/ |___ \ | | | | | |_ | _ \ / _` | '_ \ / _` | '_ \ / _` | | |_) | | | |\/| | __) | | | | | | __| | |_) | (_| | | | | (_| | | | | (_| | | __/| | | | | |/ __/ | |_| | | |_ |____/ \__,_|_| |_|\__,_|_| |_|\…

I have the temperature sensor DS18B20 connected to port 20 of the gpio as w1, if I want to connect another sensor it is as easy as adding a w2 and its port in /boot/bin/orangepiplus2e.bin [w1_para] w1_used = 1 gpio = 20 [w2_para] w2_used = 1 gpio = 10 or [w1_para] w1_used = 1 gpio = 20 gpio = 10 So or something else? thanks

Hello all I want to control some GPIO pins on my NanoPi Neo (H3) board and installed WiringNP. Executing commands results in the error piBoardRev: Unable to determine board revision from /proc/cpuinfo I've traced the source of the error down to this line, where WiringNP tries to open /sys/class/sunxi_info/sys_info to determine which board it is running on. This path is not present in my Armbian os. I'm using 4.11.12-sun8i #20 SMP armv7l armv7l armv7l GNU/Linux Am I missing something here? Or are there alternatives to using WiringNP?

Hi everyone, has anyone tried to make the above mentioned tuner work with Cubietruck? If so, were you successful? Again, if so, what are the necessary steps? It should be possible with kernel 4.11, since the latest LibreELEC distribution includes the drivers in kernel 4.9. Help would be appreciated! Thanks and cheers, chessplayer

Hi, OPiPC with latest mainline (ARMBIAN 5.34 user-built Ubuntu 16.04.3 LTS 4.13.12-sunxi). Need to test the I2S0. From what I see in patches, the I2S driver code is already there so I just need an overlay to use it. Is there any DT overlay for using the H3 I2S0 with any codec ? Even as a generic simple-audio-codec ? Christos

Hi, How can I enable both the CS0 and CS1 on the SPI on OPiPC mainline? Need to have both spidev0.0 and spidev0.1 drivers concurently available, yet only one of them is enabled and visible. My armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=72c69678-cb49-4c08-b5d3-396060e8ff18 rootfstype=ext4 overlays=spi-add-cs1 spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=1 param_spidev_spi_cs=0 param_spidev_max_freq=10000000 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u If the latest param is param_spidev_spi_cs=1 then I get only spidev0.1, if the latest param is param_spi…

Hi everybody, I would like to use the Nanopi NEO2 as firewall and therefore would like to support testing ethernet. I setup an iperf server on Nanopi NEO2 and I am running the client on my iMac to test stability of ethernet connections. After around 30-40 seconds the ethernet links goes down and is coming up back again. IPERF LOG imac:~ mobs$ iperf3 -p 5001 -c 192.168.1.100 -t 0 Connecting to host 192.168.1.100, port 5001 [ 5] local 192.168.1.109 port 53298 connected to 192.168.1.100 port 5001 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 111 MBytes 932 Mbits/sec [ 5] 1.00-2…

Hi guys , I am a newbie for armbian. I want to set my Orange Pi One as NAT server via USB connected to IPhone or Android Samsung . -------- Frist , I try to install Armbian_5.30_Orangepione_Ubuntu_xenial_default_3.4.113 Second, sudo apt-get install ipheth-utils Third, Connect to my iphone 5s via USB port and start my hotspot BUT I failed to set my phone as hotspot , I can't ping to www... I don't know what's wrong ? May any one give me a hand

Hi, I've got two questions: 1. Is possible to force more power to USB port? 2. How to totally disable wifi on board (by software) to release some power consumption?

I want to know something about the physical connection in the integrated CVBS video output. I use a jack of 3.5 mm of 4 pins. I see that the last 2 pins of the Orange pi Pc plus are the two audio outputs (Left and Rigth). other two are ground, and the other , the first one, I suppose that is the video output. but physically when I connect the jack to the video output and audio output of the orange, I can measure continuity between the supposed video output and ground. I want to know if something is wrong with that, and if I must be configure something internal in the orange for change this. in summary the audio video output have 5 co…

Hi, I am using the Armbian NanoPiDuo image and I have enable sound through armbian-config. It work well except for a small issue. When a file is sent to play, it misses out on about .5 seconds of the first part of audio. So if I run speaker-test -t wav, instead of the sound playing "front left" it just play the work left, the continues playing "front left" correctly. If I stop speaker test and run again straight away it work as planned. If I wait a few seconds the original problem occurs. To my basic knowlege, it seems like it is initialising the sound out. Is anyone else having this problem? Are there any settings I can adjust to …

I've installed this library on an Orange Pi PC Plus running 'Armbian 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i' with all updates and I would like to use wiringPiI2C but it doesn't work with either /dev/i2c-0 or /dev/i2c-1. My USB storage CRO device shows no output at all when I attempt a write to an I2C device on connector pins 3 and 5 (BCM pins 2 & 3). the 'gpio' app and 'blink' example apps that come with the library wiggles these and other pins as outputs, no trouble at all. I'm porting a library that interfaces to a DS3232 or DS3231 real-time-clock chip from Arduino and have used the initialisation sequence from the example in the WiringOP librar…

This is not to demand the devs to make the board work, I know your quite hang up on maintaining Armbian and the massive collection of boards. But I searched the forum to see if I could find it, and didn't find anything. So yeah well here is the thread about this board, in case others do a forum search. The board looks promising, but it would have been great with emmc on it, somehow they just cant get it right with these boards And if or when you need something testet, I'll be happy to help. Orange PI Zero Plus (H5) 512MB CPU: H5 Quad-core 64-bit Cortex-A53 GPU: Hexa-core Mali450 OpenGL ES 2.0/1.1/1.0 RAM: 512MB DDR3 (shared with GPU) Onboard W…

Hi guys, I know cubieboard A10 is already out of support, nevertheless I was able to make the right image work for it with a cubiescreen. Armbian gave me a way to make my own image without so much problems. The only issue I am having right now is that my touchscreen stops working after a while with errors like this: msg ft5x_i2c_rxdata i2c read error: -121 ***CTP***ft5x_read_data:893 read_data i2c_rxdata failed: -121 bus is busy, status = f9 Retrying transmission 2 I asume that my kernel patch for this touchscreen is not longer working. I have found that some guys manage to make it work under kernel version 3.4.79. So I tried to c…

Hi, I would like to know if it is possible to limit USB speed to 1.1 standard on orangepipc and how to do it? I know it is doable on raspbian but I couldn't find info about doing this on armbian

Hello, guys. I use debian server version for my board. But I can't use WiFi to connect my router. I have tried wpa_supplicat, but no result. I used many resources for information, such as https://www.blackmoreops.com/2014/09/18/connect-to-wifi-network-from-command-line-in-linux/ https://unix.stackexchange.com/questions/283722/how-to-connect-to-wifi-from-command-line Maybe, I do something wrong. Can you help me please?

Hi everyone, So far I'm using RPi2 and I would like to change to Orange Pi PC Plus or OrangePi Zero. I have questions: 1. Does OrangePi Zero share USB with LAN like RPi ??? 2. Can I install tvheadend on Armbian with OrangePi Zero? 3. Does OrangePi PC Plus share USB with LAN ? 4. Does RPi camera is compatibile with OrangePi slot?

Hi, I've tried setting up an SD Card to boot from and I'm getting the strangest issues. I've tried multiple images and even compiled my own and I'm getting the same issue. I'm booting from SD Card because I have the stock ubuntu running on the emmc right now and I don't want to flash that until I know the image works the way I want it to. Here are the logs I've got from the console on boot. I followed the directions with 7z and Etcher from the documentation page. Thanks for the help! starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage…

Hello. I have an Orange Pi PC+. I've just dd-ed Armbian 5.30 to an SD card and booted it up. Whenever i try to set the resolution to anything aside from the default 1280x720, then i only get a black screen. (I did not tried all possibilites.) How can i set my resolution to 800x480? It's connected via HDMI to a small LCD screen panel with this board. The output of h3disp: Usage: h3disp [-h/-H] -m [video mode] [-d] [-c [0-2]] ############################################################################ This is a tool to set the display resolution of your Orange Pi by patching script.bin. In case you use an HDMI-to-DVI converter p…

Hello, I'm trying to make MB1242 sonar working with my nanopi but every time I run i2cdetect, I got "i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0". Sonar works fine on RPI after changing i2c_baudrate to 50000. Is there any way to do the same at nanopi?

Hello, I know this is slightly the wrong subforum... I'm using an OrangePi PC2 with ARMBIAN 5.34.171109 nightly Ubuntu 16.04.3 LTS 4.13.11-sunxi64 I tried installing rpimonitor using rpimonitor -r after creating a "pi" user and a "pi" group That part worked. Afterwards, it told me that the webserver would be available at 192.168.0.xxx:8888 I tried that. Surprisingly, not the customized version of OrangePi-Monitor appeared, but the "original" RPI Verison. I fixed that copying /etc/rpimonitor/template/OrangePI_xx.conf to /etc/rpimonitor/template/data.conf. After restarting, it actually works, but placeholde…

Hi, is it possible to use the OTG as a mass storage device? Would it be possible to use an iso or harddrive image as "mass storage" device?

Hello, I've got two WaveShare HDMI LCDs: 7inch HDMI LCD (C), 1024x600 10.1inch HDMI LCD (B), 1280x800 Has anybody managed to configure them for the Banana (with Armbian legacy kernel)? The company WaveShare provides a Raspbian image that works okay (screen and touch). I used fbset to figure out the current settings while running the provided Raspbian image: 7inch: mode "1024x600-43" # D: 32.000 MHz, H: 27.778 kHz, V: 43.066 Hz geometry 1024 600 1024 1200 32 timings 31250 40 40 29 13 48 3 rgba 8/16,8/8,8/0,8/24 endmode 10inch: …

Hi. I am hoping to connect this type of IR receiver to my NanoPi Neo. https://www.jaycar.com.au/arduino-compatible-infrared-receiver-module/p/XC4427 I am hoping that all I need to do is connect 5v, ground and signal to the IR receiver pin to pin 6 on the header. Can anyone help me with the software and what I need to do to install lirc so the IR receiver is recognised? TIA V.

Hi, please describe in detail the process of building your own kernel and modules on Debian/Ubuntu Orange Pi Zero/R1 (Allwinner H2+) ver. 3.4.113-sun8i (armv7l): http://www.orangepi.org/OrangePiR1/ and Orange Pi Zero Expansion Interface board I'm interested in modules: bonding, usbnet, cdc_ether, usbip I will be very grateful for your detailed answer

Edit: Please see my second post in this thread. I think I've identified exactly what my problem is, please see my second post in the thread. I need to change the display mode to something that my own TV is able to display. But no matter what I've tried, I haven't been able to change the display mode. How do you do it? ---- Hello, I just got an Orange Pi PC. I installed using the Armbian_5.32.170629_Orangepipc_Ubuntu_xenial_dev_4.11.7.7z image. I'm able to log in through SSH, and I've installed all updates (apt-get update && apt-get upgrade) I have the Orange Pi PC connected to my HDMI television. The scre…

Hi. I have made a system with O Pi Lite and Armbian to automate an aquarium from where to control the light, the bubbles and with a webcam I can see the system through the web, everything automated from Cron. From a web page I can turn on and off the lights and bubbles from web buttons. Everything is fine. The problem arises when I want to put some phisical buttons for 3 things: turn off the system, change the state of light and bubbles. I have used a code in Python and the PYA20 library. This is the code. It works very well, but when I start it with the system, the program stop working soon and the buttons stop to work. #!/usr/bin/env python from pyA20.gpio…

I am using Oanrge Pi Zero 512MB, receive root mail everyday /etc/cron.daily/log2ram: sending incremental file list ./ alternatives.log auth.log daemon.log dpkg.log kern.log lastlog mail.info mail.log messages ................... mysql/error.log.5.gz mysql/error.log.6.gz mysql/error.log.7.gz sent 31,199,258 bytes received 1,265 bytes 4,160,069.73 bytes/sec total size is 40,359,412 speedup is 1.29 /etc/cron.daily/logrotate: Warning: Unit file of apache2.service changed on disk, 'systemctl daemon-reload' recommended. ? No applicable message ? No applicable message I also have orange pi pc, and check by…

Hello! I use OS armbian (2.9) on cubietruck board. I decided to upgrade to version 5.31 and have problems. Previously, parameters of hardware and interfaces SoC chip changed in the script.bin file. The bin2fex and fex2bin commands can edit these parameters. I do not understand where and what to edit (https://docs.armbian.com/User-Guide_Allwinner_overlays/) For example, how can I change the capacity of a connected battery? Previously it was the parameter pmu_battery_cap in the [pmu_para] section, its default value is 2100 I need to change it to 5000. Please help!

Hello, board: Orange pi One OS: Armbian 16.04 I installed the opi monitor using the command: sudo armbianmonitor -r error: Memory usage is not displayed, show only: Used: NaNkB (NaN%) Available: NaNkB Total: NaNkB The free memory is displayed in the statistics, but not in the Status. I try: edit file /etc/rpimonitor/template/memory.conf Locate line reading dynamic.15.source=/usr/bin/free -mk Replace this line and the following (in my version: lines 21 and 22) with dynamic.15.source=/proc/meminfo dynamic.15.regexp=MemAvailable:\s+(\d+) Save file and restart rpi-monitor . But still memory usage …

Hello all, I am very excited to install armbian debian jessie on my cubietruck ! I managed to get the Armbian_5.31_Cubietruck_Debian_jessie_next_4.11.5.img to an SD card, plugged it in, switched it on and everything went perfectly fine! Great! Now, I am trying to get this OS on the CT Nand. Sadly, the nand-sata-install doesn't work, returning the message : "There are no targets. Please check your drives". One very strange thing to me is the output of the /proc/partitions files that shows the following : major minor #blocks name 1 0 4096 ram0 1 1 4096 ram1 1 2 4096 ram2 …

I have read through the forum that Banana Pi Pro does not support directly powering drive over USB as it might be too much for this board. In my setup I use 2 A power adapter for my Banana Pi and an active HUB with power supply of 1 A, but with limit of 500 mA for HDD. Still, when connecting HUB to Banana Pi and HDD to HUB the same issue appears as when no HUB is used - the red diode turns off and Banana Pi looses power. I have already tried several HDDs (500 GB, 320 GB, 2 TB) - all with the same result. Anyone has some idea why this might be occuring despite powering drives from external source? Does Armbian have any software limitations that are creating this issue? …

Hi gurus! I'm trying to connect gc2035 camera to my OrangePi One, it's marked as SH-2035 at the cable. It is old problem, as I understand reading forum, but nothing to help me. I'm new Linux user and use Armbian 5.31, Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux. That camera works with Armbian 5.20, but I don't want to do downgrade. As I understand it needs to do right initialisation of camera in script.bin or rc.local, but what exactly?? This is part of configuration in my script.fex file: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 …

I have a problem with annoying randomly flickering cursor in armbian 5.34.171102 ubuntu desktop with mainline kernel. It's plain system after instalation, just chromium browser opened. The legacy kernel is OK on my board Orange pi plus 2e. Any idea what might cause this<

Hi, I would like to replace my Raspberry Pi 3 with an external USB where I have Gentoo Linux system to Cubietruck with Debian mainkernel in a SATA 2.5" HDD. I have some noob questions: - I want to boot from SD card and system on SATA configuration. Can I make boot partition on SD card only-read? I want to avoid SD card filesystem corruption because of my bad experience with RPi. - Is enough powerful to run Nextcloud? Just for two users. - Is enough a 2A / 5V USB powersource (connect to Jack power connector)?

Hi, everyone, I recently bought a mt7603u wireless usb dongle, which need cfg80211 module. I checked both ubuntu server and ubuntu desktop image. Can't find cfg80211 modules. How could I install cfg80211 modules? Thanks! lsmod Module Size Used by bmp085 3487 0 pcf8591 3363 0 mali 123146 0 ump 29379 1 mali 8189es 1076034 0 btrfs 712409 0

Hello, Is it possible to install serviio (armbian) ? Board: Orange pi One OS: Armbian - Ubuntu xenial 16.04

I'm testing the nightly image: Armbian_5.32.170704_Nanopineo2_Ubuntu_xenial_dev_4.11.8.img I've got it running nice and stable as a router and wifi AP, with 2 USB ports, one wifi adapter on each port. But when it's been off for a while and I power it on, it doesn't boot on the first powerup, only if I disconnect power and then wait a few seconds then power again. I've tried 2 different 2A 5v power supplies, one that I've successfully powered RbPi 2s and other Linux SBC's for months at a time, no problems. The voltage is good. I also tried a beast 10 port USB charger that has 6x 2A ports. Same behavior for all power supplies I've tried, and I…

Currently, There is no mainline release for Orange Pi One. The only release of mainline is in nightly build folder and the kernel version is v4.11.8, which doesn't work SPI chipselect. On armbian latest source compiled image, v4.13.9, SPI problem is solved. Do you have any plan to release official mainline image for Orange Pi One? Thank you very much.

We want to merge eMMC/non eMMC images and in theory, it should work. eMMC version works on my Lime2 but just to make sure I need some feedback from Micro with and without eMMC, especially most recent ones. Lime2 with or without eMMC https://dl.armbian.com/lime2/Debian_stretch_next_nightly.7z Micro with or without eMMC https://dl.armbian.com/micro/Debian_stretch_next_nightly.7z Thank you.

As title says, i am try to get the flash thing going on the UART0 on the OPI Zero (the debug ports i guess). But i got no luck, anyone has any experience with this? Thanks:)

Hi, my environment is: Orange Pi One ARMBIAN 5.34.171031 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i WiringPi fork by WereCatf: git clone https://github.com/WereCatf/WiringOP.git -b h3 ./build small c++ programm: #include <stdio.h> #include <string.h> #include <errno.h> #include <stdlib.h> #include <wiringPi.h> #include <pthread.h> static volatile int globalCounter; void myInterrupt(void) { ++globalCounter; printf("InterruptCounter: %5d\n", globalCounter); //digitalRead(7); } int main(void) { if (wiringPiSetup() == -1) { print…

Hi I have an ARM-based board(http://wiki.friendlyarm.com/wiki/index.php/NanoPi_M1) and use Armbian(Ubuntu-server 16.04) on it. I have a 2.2" TFT-LCD with SPI connection, and use this framebuffer driver(https://github.com/notro/fbtft) to launch it. I can setup my LCD with this command: sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:201,led:6 speed=16000000 rotate=90 bgr=1 And before, when I had Ubuntu desktop, I could change display by this command: FRAMEBUFFER=/dev/fb8 startx But in Ubuntu-server I get this error message: X.Org X Server 1.18.4 Release Date: 2016-07-19 X Protocol Version 11, Revision 0 Buil…

Hi all ! I try to turn off ethernet leds on Nano Pi Neo. I don't use network-manager (which disables leds when ethernet cable is disconnected) because I need to use ifup and ifdown... I tried to see (without success) : cd /sys/class/leds cd /sys/class/net/eth0/ h3consumption -e off I know that it's possible on banapi (with a github library), is it possible on nano pi neo ? Best Regards

No nameserver in these files too /etc/resolvconf/run/resolv.conf /run/resolvconf/resolv.conf The nameserver is set in this file only /run/NetworkManager/resolv.conf This is the content of /etc/NetworkManager/NetworkManager.conf [main] dns=none plugins=ifupdown,keyfile [ifupdown] managed=true [keyfile] unmanaged-devices=interface-name:p2p0 These are relevant lines from systemd journal: Oct 29 21:47:24 orangepilite NetworkManager[507]: <info> [1509306444.9814] dhcp-init: Using DHCP client 'dhclient' Oct 29 21:47:29 orangepilite NetworkManager[5…

Hi all, I recently purchased an orange pi after developing on the raspberry pi (just for convenience). I got it mainly because the integrated memory could be a real asset both because SD are faulty when making lots of memory accesses and emmc can provide a nice layer of code protection when giving the board to somebody else. I set-up everything without issue and I used the nand-sata-install to move everything to emmc...it worked like a charm. I then placed all my proprietary code on emmc and executed without issues. Problem is, I can obviously still insert an SD card and then mount the emmc and access my code since the SD is booted before the emmc.…

Hello everyone, I am using Nanopi air and I wish to have ethernet and mass storage simultaneously. I went through numerous problems but now I have OTG working. If i try modprobe with g_serial, g_ether, or g_mass_storage, each works individually. Even g_cdc ( ethernet + serial ) and g_acm_ms ( mass storage + ethernet ) work. when I try to run : modprobe g_multi file=/sdcard.img I get the following: [ 290.720691] g_multi gadget: unable to autoconfigure all endpoints [ 290.880936] g_multi musb-hdrc.1.auto: failed to start g_multi: -524 Please help

Hi! I need some help. I built a little torrent server, home media center from opipcplus. It runs transmission all day all night with a heatsink and it keeps the cpu temp under 55°. But if i start kodi or other player the temp jumps to the sky near 80°. i bought a cooling fan and with the heatsink it keeps the cpu under 35° without any problem. its great but it noisy and frustrating. How can i control the pins to automatic turn on and off the fan? can someone send a script or anything help? thank you

Hi Has anyone got the on board Bluetooth going on their OP Prime ?

Hello Everyone, At first I'm sorry for my English I started working with Ubuntu server version -> Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. For my purposes I needed to enable watchdog on my board. It took me a while, but I managed to do it. After setting up whole configuration, and then start stop tests everythink seems to work just fine (watchdog reboot my bord). To finish whole process I wanted to enable wdog to start at boot, but it didnt activate after reset. After some digging in Internet and investigation i figured out that in watchdog.service file one line is missed which was in all other services. So after a…

I've installed Armbian again. Initially I logged in as root and 1234 password which worked. Then it asked to change the password. Something wen't wrong with it. My OrangePi PC boots fine and ok. When I open a terminal and try to do a "sudo this that" it asks my password and won't accept the one I gave, nor 1234. I've done the full installation a couple of times and same problem persists. How do I rest root password? The problem is that everytime I re-install everything and I'me at the very firts log (where I enter root and 1234) the screen scrolls so that I cannot see what it is asking since my monitor is 1600x1024. That I why I need to reset password afterwards. I…

Today I did get my NAS-Case "Neo Station NS-120B" for my NanoPi Neo2 (also useable with a normal NanoPi Neo). Because I already did use the Neo2 with armbian (and had soldered all pins on the mainboard - I ordered only the case without a new Neo2 with soldered pins) I didnt want to write the FriendlyARM Image for NAS to my uSD. After completing to built the Neo2 and the 2.5 HDD inside the case (and using the 12V PowerSupply I had) armbian did start up and I could normally SSH into my Neo2 - BUT I cant see the HDD or the HDD-controller (which should be connected via USB). ( @tkaisernow here the Neo2 do get his power over pins and not via the Mic…

Today I was going through my cupboard and did find a original pcDuino (v1) with A10-CPU and 1GB of Ram. In my mind I got the pcDuino v2 download-page of armbian. As JohnGo did wrote May 2016 on this page is a picture of the pcDuino v1: So I checked the specifications v1 <--> v2 and found ony that v2 has only a WiFi-Board soldered where on the v1 is a additionally USB-Port. Also the v1 is missing the Arduino-Headers, but has some other pin-rows for GPIO and so on. CPU (single-Core 1Ghz) and Ram (whopping 1GB for 2012) is the same I wrote the pcDuino v2 Image to a uSD and booted it without problems. (and changed /etc/upd…

Hello, I have just built an image with the default parameters of the Lime A20 board. It seems that the system does not detect any sound card. aplay -l aplay: device_list:268: no soundcards found... uname -a Linux lime 4.13.6-sunxi lsmod Module Size Used by cfg80211 376832 0 rfkill 20480 1 cfg80211 sun4i_gpadc_iio 16384 0 evdev 20480 1 at24 16384 0 sun4i_ts 16384 0 sun4i_gpadc 16384 0 nvmem_sunxi_sid 16384 0 sun4i_ss 24576 0 uio_pdrv_genirq 16384 0 uio 16384 1 uio_pdrv_genirq As you can see above, there is no module related to sound. …

Hi, I have problem with my Orange Pi PC, where I installed Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. I install python-jabberbot and python-daemon to create daemon to do queries by jabber comunication protocol. When I am active on ssh I get answers from bot in seconds, but when I try get answer without, I must wait about 1-2 minutes to answer. Do you konow what may be responsible for this behavior? Best regards, Leszek Mazur

Hello, I get an error when i try to use the PH5 pin as digital output. PH5 is the number 229 according to the following equation: (8-1)*32+5 = 229 echo 229 > /sys/class/gpio/export -bash: echo: write error: Device or resource busy If i use other pins like PH13, PH19, PH20 or PH21, all work correctly. For example, for PH13 as digital output: echo 237 > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio237/direction echo "1" > /sys/class/gpio/gpio237/value echo "0" > /sys/class/gpio/gpio237/value echo 237 > /sys/class/gpio/unexport I get the same error in the Cubieboard2 …

Hy, Someone could say me if PPP is in the Kernel natively? Thanks

Hi, I am having doubts on how to use I2C ADS1115 unit on Orange Pi Lite. I already have I2C module and tools installed (see below). Thing is, where do I get the Phyton library to make use of it? Are there any examples? The other question is about wiring. When I connect to twi0 I cannot see the I2C device: root@orangepilite:~# i2cdetect -y twi0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- --…

Good night, I have the sound problem but with hdmi audio, de default is the 3.5 mm audio jack, then I looked for the asound.conf in /etc, then I found that this file doesn't exist and after that I've created it with the following content: pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } the problem is that even created this way the sound output still being the 3.5 mm jack and I don't know if I need to change some setting to mpv player to output the sound through hdmi. What else can I do to change the sound from audio jack to hdmi?

Hi all Does anyone recall if with kernel 4.9 it is required to put some patch for enabling power on the USB Host port of BananaPi? I am using vanilla kernel in another project, (LEDE) and when switching to kernel 4.9 I don't have any power from the USB port The dts is the vanilla one and AXP20x power driver is enabled Thanks!

Hi I am new in the forum and the happy owner (as of yesterday) of an Orange Pi Lite. Nice little board. I managed to install Armbian server, configure Wi-Fi upgrade and install apache / php and mrtg. I also was able to enable one wire protocol to play around with a DS18B20 thermometer. My idea is to create an automated garden watering system with nice stats (graphs) I already have a 4 channel relay board (to connect solenoid water valves), a DS18B20 to sense temperature, an LDR to graph sunlight hours and 4 hygrometers --moisture sensors--. Those I want to connect through an I2C ADS1115 ADC module (which I also already have). …

hey guys, i just got my nanopi m3 today... and see that the download for it is gone from the site? -can anyone help? -erik

Sometimes i can't access to my banana thru ssh and etc. Link led is blinking. It happens everytime in HH:16:00 with random hour. In syslog i get this messages: i don't understand what is this... Everytime syslog messages are same

Hey guys, I would like to interface a small RGB24 LCD on the H3 GPIO, similar to this on raspberry pi : https://www.raspberrypi.org/documentation/hardware/raspberrypi/dpi/README.md http://blog.reasonablycorrect.com/raw-dpi-raspberry-pi Is this feature already present on armbian device tree overlay? If no, how would one make it? Could someone help drawing the big picture so I know where to start? After having a look at this section : https://docs.armbian.com/Hardware_Allwinner_overlays/ I understand that it would require writing a dt overlay (.dts file) to attribute the different functions to the GPIOs. But then how to wri…

Hi, I have a OrangePi+ 2E running ARMBIAN 5.33 user-built Debian GNU/Linux 8 (jessie) 4.13.5-sunxi The system is installed and runs well from EMMC, but now that I have it set up more or less as I want it, I tried to boot from sdcard to do a emmc backup as here I tried first plugging the original SD that was nand-installed to emmc, but the system would only boot to emmc, su did a fresh install of armbian next to a new sd card, but the system will still only boot from emmc. Any ideas? BR.

Board OPi Zero 512, NEXT kernel 4.13.7, last Sunday compiled. I'm trying do start more than one Dallas 1 wire interface. My primary idea was to add second w1-gpio overlay but no success. The next one is to edit device tree for w1-gpio to add another pin, and then to edit fixup script. And need some help to understand this ( copied from sun8i-h3-w1-gpio.dts ) fragment@0 { target = <&pio>; __overlay__ { w1_pins: w1_pins { pins = "PD14"; function = "gpio_in"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { onewire@0 { compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&w1_pins>; gpios …

Hello, My hardware is BananaPi and I would like to enable early KMS start. As per https://wiki.archlinux.org/index.php/Kernel_mode_setting#Early_KMS_start , I need to add "the display driver kernel module" to initramfs. With a normal x86 PC, the kernel module to add would be 'i915', 'radeon' or 'nouveau'. But I'm a bit confused with the sunxi hardware. Which module am I supposed to add? Thanks!

The "desktop" image for Banana Pi used to be based on Debian Jessie, but now it has been replaced by a Ubuntu xenial based image. For some reason I need the debian image, but after checking https://dl.armbian.com/bananapi/archive/ I did not see the old images. Is it possible to have the old image now? Thanks! (I have been using that jessie desktop image for a long time until just now the SD card died...)

Is there any option to change the boot screen of the armbian in orange pi, during startup. And i also want hide the boot text during shutdown. I m new to armbian and orange pi I m using orange pi pc plus 2E. Can anyone help me please. Thanks in advance.

Has anybody a good latency after the RT-PREEMPT patch? I'm using Orange Pi One (H3), Ubuntu Desktop and legacy 3.4.113 kernel patched with 30-real-time143-full-plus-rt-fixes.patch. Also I have the isolcpus=3 enabled. And latency test results for this config is master@orangepione:~/rt-tests$ sudo ./cyclictest -a -t -n -p99 # /dev/cpu_dma_latency set to 0us policy: fifo: loadavg: 2.18 2.49 1.19 1/299 3693 T: 0 ( 3034) P:99 I:1000 C: 364441 Min: 7 Act: 31 Avg: 23 Max: 3655 T: 1 ( 3035) P:99 I:1500 C: 242985 Min: 7 Act: 32 Avg: 23 Max: 3578 T: 2 ( 3036) P:99 I:2000 C: 182252 Min: 7 Act: 43 Avg: 20 Max: 2198 …

Hello guys, I have an BananaPi M1 board runing armbian 5.31, already installed apache and mysql months ago, also an sata drive and the box is running smooth, I have alot of sensors around the house that are pushing new values to my mysql database, every minute, or every few minutes, but now I want to setup my cameras to use the FTP to store images in a folder accessible by apache, when cameras detect motion, can you point me in the right direction to install a FTP server I want to be able to see all the images saved by the cameras, in my dashboard, a website I made and host in this BananaPi box.

Hello. I hava a serious problem with an Orange Pi Zero and it´s sound ouput: I just can´t get it working. :-( Hardware: Orange Pi Zero (H2+/512MB) with the Orange Pi Extension Board. Software: Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113 (Linux orangepizero 3.4.113-sun8i #16 SMP PREEMPT Tue Jun 13 14:15:57 CEST 2017 armv7l armv7l armv7l GNU/Linux) I already tried this link for activating Line-Out in general, but it is still not working: "speaker-test" does still not bring any sound to teh 3.5mm jack. My actual "alsamixer"-config as shown by "nano /var/lib/alsa/asound.state": state.I2SES8…

Hi, I'm Glego and this is my first post. I was just fiddling around with my old BananaPI M1 and M1+, and stumbled upon ARMbian, which has great appraisals on the Bananapi forum. I'm creating a cluster of various SBC's and thought ARMbian is the OS to go. Unfortunatly I had an issue when setting up Docker and wanted to share the resolution for future reference. However I couldn't find the root cause, so if any expert would be able to comment on why this is happening, I will be happy the do the tests again. Cheers, Glego Issue After installing docker-ce, the service is not starting: docker.service start request repeated too quick…

Bonjour, je viens d'acquerir une opi win plus j'ai téléchargé et installé sur une carte scandisk ultra 32gb et au boot j'ai le message can not setup simplefb node not found l'image utilisée est Armbian_5.32.170705_Orangepiwin_Ubuntu_xenial_dev_4.11.8.img. Need help tks

Hello , How do I get RTC working on Banana Pro. I think I have 2 options 1. Built in one 2. External [DS3231] Here is some info about the setup i got. dmesg | grep -i rtc [ 1.928725] sunxi-rtc sunxi-rtc: Warning: RTC time is wrong! [ 1.934023] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 hwclock --test -D hwclock from util-linux 2.27.1 Using the /dev interface to the clock. Last drift adjustment done at 1506000286 seconds after 1969 Last calibration done at 1506000286 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... select() to /d…

I tried to create my own image using the build script for Orange Pi Zero. But starting this crashes immediately. Any suggestions? U-Boot 2017.09-1 (Oct 13 2017 - 11:04:53 +0200) CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: phy interface0 eth0: ethernet@1c30000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3382 bytes read in 125 ms (26.4 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded f…

Hi, if anybody can suggest if mentioned situation is OK? Thanks in advance. Originally all my OPI boards have been running on 624 MHz for DDR frequency. 2 days ago I decided to remove fans from My Orange Pi+ 2e and Orange Pi+ 2 (following suggestions from forum as fan is maybe not required). 1. Orange Pi+ 2e (this is running all my services which is: nextcloud, mail server, svn and web server to access mentioned) - originally with heasink and fan (as you can see downtime on Oct 14th - when I have removed fan and keep only heatsink). But something happened - with fan ddr frequency was always 624 MHz. Without fan some time after reboot it is increasi…

Hi, Got OPiPC with legacy and Ubuntu desktop, build 5.33. Gonna attach some external dynamic mic to OPiPC in place of the on-board condenser mic, replacing it. How can we stop the mic bias voltage? Can we do that from Alsa or Pulseaudio? Christos