Allwinner sunxi

Hi, When I scan the I2C with i2cdetect, I get the following, without connecting any i2c device. May I know which device on the motherboard is taking up the three addresses. Thank you sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: 50 -- -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -…

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

I have tried 3 Orange Pi 3 images on my orange Pi 3 LTS. None of them will mount the root fs and continue booting. It shows btrfs, but the partition is ext4 and the armbianEnv.txt file has the correct UUID and ext4 stated. I can boot an image from the OrangePi website, so I am 99% certain it is not the power supply or sd card.

Hi, I want to use LCD on Orange Pi 3 LTS. But there are no fex/script.bin in the boot directory. The LCD pins are given the RGMII Ethernet Interface. I could not configure the device tree for internal LCD output. Could you please explain how can i use LCD on these system ? Good Work.

Flash 25.2.0 (The Latest Built Dec 01) to a SD card and boot a Orange Pi 3 LTS, Ethernet lost after sudo reboot the board. It did not even come back after physically power off and on. Have anyone experienced the same problem? The same board worked very well with Debian Bullseyes (downloaded from http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/service-and-support/Orange-pi-3-LTS.html). I googled and found Orange Pi 3B has similar problem. https://www.reddit.com/r/OrangePI/comments/1aojmn3/orange_pi_3b_ethernet_doesnt_work/

Hi there, OK, here's the picture: brand new Orange PI 3 LTS, made SD card with Armbian 22.08 sid - didn't boot; made SD card with Armbian 22.05 Jammy - still the same result. The result: [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] bootconsole [earlycon0] enabled WARNING: Unimplemented Standard Service Call: 0xc0000026 and on top of that, upon first boot Armbian copies itself to the eMMC? Because after removing the SD card, I was able to get the same result with just plugging in the power (it boots from eMMC...?). As far as I remember, I didn't see any similar behavior described in the documentation. …

After an "apt upgrade", the kernel was switched to "Linux 6.6.16-current-sunxi64" (Armbian 24.2.1 Jammy). On the WiFi side, no problem, but for Ethernet, it no longer seems to detect the link. So I downgraded to "Linux 6.1.77-legacy-sunxi64" with armbian-config. After this, the Ethernet works again. Do you have any idea where this could come from? And if this can be fixed in future versions?

I've had an Orange Pi 3 LTS for a couple of months now. I bought it for use as a home theater tv box. I thought I'd use the official orange pi ubuntu release, but it turned out to be really outdated and broken. So I have been trying to get Armbian to work. After a lot of troubleshooting and time spent reading docs and forums, I can't get the thing to play video properly. It plays but is terrible quality and stutters constantly. I've determined that panfrost is working. In orangepi-config, under Hardware, it says the GPU is enabled. But when I run glmark2 I get a score of 100 or less no matter what I do. I've tried old builds of armbian for the pi 3 lts and the…

Hello, does this USB WiFi card work with armbian on Orange Pi 3 LTS? TP-Link Nano AC600 USB Wifi Adapter https://www.amazon.com/dp/B07PB1X4CN/ Does it need any drivers to be installed? If yes, is there any that is working with OPi 3 LTS? Btw I want to use this wifi adapter, because Armbian doesn't work with internal wifi card in this SBC - https://forum.armbian.com/topic/23505-orange-pi-3-lts-no-wifi/ (and sadly Devs didn't release a fix for it)

With Armbian 22 (kernel 5.15 and bullseye/jammy) the Orange PI 3 LTS worked great including WiFi, ETH, Bluetooth. Partly thanks to @Ukhellfire and @going. Downloadable here: https://xogium.performanceservers.nl/archive/orangepi3-lts/archive/ Below is what I find the status is for the new Armbian 23 images provided for here : https://www.armbian.com/orangepi3-lts/ Branch current: Main downloads Armbian 23 with kernel 6.1 bookworm: It boots, but every 3rd or 4th keystroke is ignored. No ETH, no WiFi. Armbian 23 with kernel 6.1 jammy: It boots, keystrokes are OK, ETH is OK, but WiFi doesn't work. Branch edge: Rolling release…

Hello, I installed Ubuntu Bionic on sdcard and run Kodi on OrangePI but it seems very hot and hang out to reboot every 5mins. Do you encourter the same problem? And how to install Ubuntu into eMCC?

Hi, I'm back to China and got the NEWEST Orange Pi 3 at hand. But, it looks this new SBC has NOT been supported yet (please refer to https://www.armbian.com/download/?tx_maker=xunlong) ? Just expecting when will the armbian support for Orange Pi 3 out? Cheers Pei

Hi guys! I have a problem with Orange Pi 3. After a night leaving the small board turned on I reboot the board and try to use a Bluetooth connector it shutdown. Again and again the same problem. When I touched the board it was so hot. Even when I use outside the case the board can't support a process for at least 30 minutes without turning off. I got the outputs of dmesg. As I don't know, I am a replay newbie, I ask for help here. Best regards. Paulo

considering to buy orange pi 3 with new H6 cpu, usb3.0 port and onboard emmc, but everyone has been complaining official images, just wondering if orange pi 3 will be supported soon.

Under kernel 4.9, using a usb3.0 to Gigabit interface with RTL8153b card, the upstream and downstream speed can reach Gigabit. But with kernel5.10, the speed can't reach gigabit, and the driver file has been changed to the latest version, but still no effect. kernel5.10 Speed measurement root@orangepi3-lts:~# iperf3 -c 192.168.3.201 Connecting to host 192.168.3.201, port 5201 [ 5] local 192.168.3.146 port 44376 connected to 192.168.3.201 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 24.8 MBytes 208 Mbits/sec 0 147 KBytes [ 5] 1.00-2.00 sec 23.5 MBytes 198 Mbits/sec 0 147 KBytes [ 5] 2.00-3.00 sec 23.5 MBytes 197 Mbit…

How do i enable UART 3 in an orange pi 3-LTS. i checked the /boot/armbianEnv.txt file and it has overlay_prefix=sun50i-h6. i then did a sudo armbian-config > System > Kernel > SYS210 Manage device tree overlays > enabled sun50i-h6-uart3 > reboot. after all that i am still only seeing ttys0 when i do a dmesg | grep tty

Hi, I am facing an i2c problem on orange pi 3. The i2c0 is enabled in armbian-config. The i2cdetect output is correct, as I know my two slave boards connecting to gpio pin3 (SDA) and pin5(SCL) have the addresses 0x20 and 0x23. pi@orangepi3:~$ sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 -- -- 23 -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -…

Hello! Here's the outputs: $ uname -a Linux opi3 5.4.28-sunxi64 #20.02.7 SMP Sat Mar 28 17:25:10 CET 2020 aarch64 GNU/Linux $ sudo aplay -l **** List of PLAYBACK Hardware Devices **** card 0: allwinnerhdmi [allwinner-hdmi], device 0: 5091000.i2s-i2s-hifi i2s-hifi-0 [5091000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 ...and that's all! There's no second card. I tested HDMI sound with my TV -- works fine, sound plays. But I need to use 3.5mm jack. Is it physically damaged? Or what could I do? Help, please!

Dear All, I try to use the UART3 on my Orange Pi mini but it just won't work. I put a jumper on Pin 8 and pin 10 on the header. Also give read/write premmission to all users. Based on this UART3 is /dev/ttyS2 [ 0.000000] console [tty1] enabled [ 0.954713] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A [ 0.985810] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A [ 1.016890] sunxi-uart.3: ttyS2 at MMIO 0x1c28c00 (irq = 36) is a U6_16550A [ 1.047968] sunxi-uart.7: ttyS3 at MMIO 0x1c29c00 (irq = 52) is a U6_16550A [ 6.014770] systemd[1]: Expecting device dev-ttySAC2.device... [ 6.681738] systemd[…

I've tried both Armbian_5.00_Orangepi_Debian_jessie_4.4.1 and Armbian_5.00_Orangepi_Ubuntu_trusty_4.4.1_desktop (needs the Option "HWCursor" "off" in /etc/X11/xorg.conf). On both, after some minutes (hours?) of inactivity video id off and I 'cant turn it on. A restart fix the problem. Apart of the video, everything works just fine. I can login via SSH with no problem. Any clue?

I am a long-time Linux user, who casually and confidently and regularly uses the software 'Update Manager' in Linux Mint to keep my software up-to-date. I also have no problem using 'apt update' to update specific software packages. What I am more careful about is ever using 'apt upgrade' and 'apt dist-upgrade' -- almost never doing so. What advise is there for updating the software on my Armbian Orange Pi PCs? darren@frodo10:~$ sudo apt list --upgradable Listing... Done armbian-config/stretch 5.45 all [upgradable from: 5.38] armbian-firmware/stretch 5.45 all [upgradable from: 5.38] tzdata/stable-updates 2018e-0+deb9u1 all [upgradable from: 2018d-0+deb9u…

Hi, i discovered and solved incompatible gc2035 driver with some v4l2 applications. I made some modifications to the 3.4.39-02 kernel-lobo: gc2035: of 8fps to ~20fps eand improvements in the matter of light. The original driver accepts only 800×600, added the following resolutions: 800×600/640×480/320×240 sunxi_wdt: builtin to module (greater flexibility to change the module options) / pr_info some functions, causing flood in kern.log (switched to pr_debug) CONFIG_CMDLINE=â€earlyprintk=ttyS0,115200 loglevel=5 initcall_debug=0 console=ttyS0,115200 console=tty0 fsck.mode=force fsck.repair=yes init=/init ipv6.disable=1 kernel size: ~59mb For more informa…

Hello there, I was looking at the gc2035 camera sensor for the orange pi device. I want the camera module to load as fast as possible and take pictures as fast as possible. When I use a USB camera, it takes 2-3 seconds to load the module and activate the camera, and the camera takes 2 seconds. I'm thinking of compiling the GC2035 camera statically to the linux kernel. But I'm not sure how much time decrease. What I would like to know is, how fast is the camera taking pictures and how long is the loading time of the camera modules? Can I take pictures under 200 ms with the camera triggered? The Raspifastcamd module allows …

Hello, I recently installed Armbian 5.85 legacy on my new Orange Pi Lite in order to try out my new Orange Pi camera, but it's not being recognized at all, even after following the instructions in this topic: I already tried doing the following (as root) unsuccessfully (no errors returned, but still can't detect camera): sunxi-pio -m "PG11<1><0><1><1>" #DOVDD sunxi-pio -m "PE15<1><0><1><0>" #Power_Down sunxi-pio -m "PE14<1><0><1><1>" #reset modprobe gc2035 modprobe vfe_v4l2 Here's the output of lsusb: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001…

Hi, I am using orange pi lite. and loaded debian desktop.. it says it connected to wifi network. But I am trying to browse internet with chromium. It can't reach to the internet. it cant upload since there is no internet connection so I took pictures of reult of command armbianmonitor -U as much as I could. Here are the screen shots. https://ibb.co/jMyjKb https://ibb.co/kPK8eb https://ibb.co/hRndeb https://ibb.co/cdsdeb https://ibb.co/ihXiCw https://ibb.co/f6RRXw and I dont know how to fix. this Can someone help me? Thank you.

i did some experiments today, i tested 2 Orange pi with the same image debian buster in the lastest version. i put a script on both that reported the execution time of a function and the date, one is running smoothy, the other crashes the orange, the bottom is the log what caught exactly at the time it caught, could someone help me understand it? Mar 19 09:25:01 localhost CRON[1657]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Mar 19 09:30:01 localhost CRON[1702]: (root) CMD (/usr/lib/armbian/armbian-truncate-logs) Mar 19 09:31:52 localhost systemd[1]: Stopped target Timers. Mar 19 09:31:52 localhost systemd[1]: Stopped Message of the D…

Hello, this is my first topic on the forum. Please forgive my English is poor. I use Orange Pi PC, version Armbian_5.05_Orangepih3_Debian_jessie_3.4.110, with a patch to kswapd0: CMA-linux-image-sun8i_5.07_armhf.deb from this: https://github.com/igorpecovnik/lib/issues/219 SD card is: SanDisk microSDXC UHS-I 64GB speed up to 48MB/s (write speed in OPi is over 20MB/s). I have a problem that when writing to the card. For example, downloading a file by multiple instances wget. The SD card stops responding and crashes Opi. Only helps to disconnect the power supply. The card is new and fully operational. When I connect the monitor displays the following messag…

Hello First, sorry for my English Second, the problem... I have an Orange PI Zero 3, 4gb I install the OS without any problem, the image I use is the following: "Armbian_23.08.0-trunk_Orangepizero3_bookworm_current_6.1.31-1GB-2GB.img" I configure the network with the program "nmtui", everything is fine. I enter through ssh since the screen is not detected through HDMI, I do an apt update and then apt upgrade... everything seems correct, until I do a reboot... my Orange Pi does not start anymore. I am interested in installing openmediavault, that is why I resort to a debian image. What is the problem? I am not using the correct image? I need your help

Hi! I think all fine in my configuration, but not connect on boot, I need to killall -q wpa_supplicant and run /etc/init.d/networking restart to connect. # /etc/network/interfaces iface wlan0 inet static address 192.168.1.200 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 pre-up wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf -wB -D <forgot the name> post-down killall -q wpa_supplicant

Currently I receive rustc crashes after memory usage get to 3GB (1GB RAM + 2GB SWAP) when building firefox. After looking around why, I found that kernel isn't build with lpae extension. Although H3 soc supports lpae (Large Physical Address Extension), but kernel has CONFIG_ARM_LPAE flag not set and so we can't use more than 3GB of memory (1GB is reserved for kernel). (Processors that implement the ARMv7-A Large Physical Address Extension (LPAE), expand the range of accessible physical addresses from 4GB (232 bytes) to 1024GB (240 bytes) a terabyte, by translating 32-bit virtual memory addresses into 40-bit physical memory addresses.) After looking a…

Hello, I am trying to use g_serial but it does not work. I'm using fresh install of armbian (Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.7z), with apt-get update/apt-get upgrade/armbianconfig Install headers. Linux orangepilite 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux This is the overlay I use to enable OTG: sudo /usr/sbin/armbian-add-overlay usbotg.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&usb_otg>; __overlay__ { dr_mode = "otg"; status = "okay"; }; }; }; After rebooting OPi there are several erro…

No nameserver in these files too /etc/resolvconf/run/resolv.conf /run/resolvconf/resolv.conf The nameserver is set in this file only /run/NetworkManager/resolv.conf This is the content of /etc/NetworkManager/NetworkManager.conf [main] dns=none plugins=ifupdown,keyfile [ifupdown] managed=true [keyfile] unmanaged-devices=interface-name:p2p0 These are relevant lines from systemd journal: Oct 29 21:47:24 orangepilite NetworkManager[507]: <info> [1509306444.9814] dhcp-init: Using DHCP client 'dhclient' Oct 29 21:47:29 orangepilite NetworkManager[5…

Hello guys, I read a lot but did not find the answer I'm trying to Turn ON / Turn OFF my Orange pi lite HDMI output like with my raspberry pi (with the help of /opt/vc/bin/tvservice -o ... etc) But I'm not able to find a similar command to do it. I only found some tips to do it at start-up only My goal is, after some times, turn OFF HDMI output (via python script) to force my monitor to switch into sleep mode. Do you have any ideas ? Thanks in advance Max

I have a question, does anyone know a method to start in the Opi Lite system the I2S audio interface and in particular I mean the module: PCM5102 / PCM5102a On my old OrangePi Lite board, sound and audio in the configuration as mentioned above really work great ... but unfortunately the Armbian system that I use is no longer supported. This is the Ubuntu version (xenial) and kernel: 3.4.113-sun8i, I managed to update some programs important to me, e.g. mpd / mpc but not to the latest versions. I also have another version of OrangePI 3 LTS and I know that on this model it is rather impossible to start I2S + PCM5102 so I used a good sound card under USB and it is OK. Ho…

I can't get my Orange Pi working... After writing image to a SD card, the system boots up and the green LED lights up. Everything looks ok, until "Starting kernel..." line. After that the screen goes all black or displays artifacts. I tried different HDMI cables but still same issues. I've been trying with 5.25, 5.30, 5.35, 5.38 Ubuntu versions. I found out that the only way to get the system up and running was installing version 5.30, because the system boots with 720p mode. Other builds use 1080p mode. However when I "apt upgrade" the kernel, system boots with 1080p and the issue shows up again. Is there a way to "force" Armbian to use 720p mode by default?

Hello, I know there is documentation about it, but I think I've tried everything and my orange pi is still not displaying on my hdmi screen. The green LED is active, and the red one is blinking. I've written a Raspian image to the sd card, corresponding with the board. I have read about bin2fex but I can't have access to my sd card data on my Windows, to execute bin2fex. Thank you for your help !

Orange Pi Lite, it comes with H3 SoC, 512MB DDR3 SDRAM and WiFi, NO ethernet port WiFi: Xunlong said they replace 8189ETV used on the older OPi with 8189FTV on OPi Lite, PC Plus and Plus 2E (Thx TK). Is now available for USD 12.- Some critical words about it. Edit: added WiFi information

board in WIFI mode phy#0 Interface wlan-ap ifindex 3 wdev 0x1 addr 02:81:1d:98:1c:bc ssid tomesh-8583 type AP txpower 12.00 dBm Drivers seems to crash as soon as i try to associate the first device with it Any one know what could be causing it? hostapd.conf interface=wlan-ap hw_mode=g channel=11 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ssid=tomesh-8583 wpa_passphrase=password123456 [ 40.084416] Unable to handle kernel paging request at virtual address e1f27e64 [ 40.091697] pgd = 1…

Hi, as it is quite hot now in Europe, one of my boards is experiencing overheat and shuts down automatically: Jun 25 16:52:27 localhost kernel: [74505.568246] thermal thermal_zone0: critical temperature reached (90 C), shutting down Who is initiating this shutdown? Is it possible to: 1. Change the temperature value that triggers the shutdown 2. Hook a script instead of direct shutdown so I can handle the overheat Thanks

Hi, I always have a boot problem with the OP lite after operating approximately for 2 weeks !! When the problem occurs, I got the following message while the system is booting : U-Boot SPL 2017.01-armbian (Feb 02 2017 - 02:58:38) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2017.01-armbian (Feb 02 2017 - 02:58:38 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Lite DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 6944 bytes read in 136 ms (49.8 KiB/s) switch to partitions #0, OK…

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Aud…

Is there way to configure sound over hdmi? Display is working ok (configuration for 1366x768 and 1920x1080 was made manually), but there is no sound.

Hi, I just wanted to report this bug. Latest Armbian Buster images for OPi Lite 2 don't work. When they're booted up, it takes 30 seconds for the device to freeze completely. The screen, keyboard, network, everything is frozen after less than a minute. I downgraded to a release from a month ago and it boots up correctly.

how can I force set HDMI output like 1024x768 60hz or something like that? hello I have OPI lite 2, I use Armbian_5.61.180927_Orangepilite2_Ubuntu_bionic_dev_4.18.10.img, when I boot OPI I can see preboot information then after 1-3 sec I have no signal on my monitor I tried different hdmi cables without luck uname -a Linux orangepilite2 4.18.11-sunxi64 #312 SMP Sun Sep 30 00:22:52 CEST 2018 aarch ps: monitor dell 2414h I tried different OS like android (native, zidoo h6 pro, beelink gs1) also ubuntu 16.04 without any monitor issue, at least video output worked at any cases but they have another issues

My docker build dev 5.0.y is not booting from sd card. U-Boot SPL 2019.01-armbian (Mar 16 2019 - 05:27:40 +0000) DRAM:This DRAM setup is currently not supported. resetting ...

Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux I have managed by accident to get full USB3 speed on orange pi lite 2. I have bought a USB3 hub: "Bus 004 Device 002: ID 05e3:0612 Genesys Logic, Inc. Hub" , I have no idea which chip it has, it is in an aluminum case and looks like the one on the attached picture but black. By attaching atleast two usb devices in the hub USB3 somehow gets into full speed mode, one of them has to be USB2 device. I have managed to get with all devices I have ATM about 2000Gbs including iperf in both directions with rtl8153, hdparm -t on two usb2 memory sticks …

Hey all, I understand these things are in active development at the moment. I was attempting to use the usb 3.0 socket on the lite 2 with stretch, except it did not respond at all - looking at dmesg shows the following error: [ 1.806055] sun4i-usb-phy 5100400.phy: Couldn't get regulator usb0_vbus... Deferring probe [ 1.806320] sun50i-usb3-phy 5210000.phy: failed to get phy clock which from my limited experience with linux kernel seems to indicate that the device tree config may be incorrect for the board - as most searching for these errors show the code added as part of updates to get the pine64 board's usb 3.0 stack working. USB 2.0 sock…

Hi, I bought brand new Waveshare 3.5 inch (A) RPI touch screen and also a opi lite but I have got problem with installing the lcd on my pi , when I plug it in it show me only white back light please help me ( my os is raspbian).

Hello, i had a problem withe an Orange Pi Lite and the Cheap RPI Display. The Display Backlight is on. I had used this tut: https://forum.armbian.com/topic/6737-orange-pi-zero-35-tft-touchscreen/ https://forum.armbian.com/topic/4837-guide-how-to-use-touchscreen-lcd-on-h3-devices/ --- 2) Create a makefile (Take note that it is TABS instead of spaces before the $(MAKE)) nano Makefile Insert the below in without the ----- -------------------------------- obj-m := ads7846.o KDIR := /lib/modules/$(shell uname -r)/build PWD := $(shell pwd) all: $(MAKE) -C $(KDIR) M=$(PWD) modules clean: $(MAKE) -C $(KDIR) M=$(P…

Hi i have a orange pi lite,i try this https://yudanta.me/installing-wi ... orangepi-pc-device/ in armbian terminal but after the installation i try with my button arcade on gpio pin but never working,if onyl work 5v with ground(make reset button) i have used many button and switch but work only the reset button Where is wrong? thanks

Hi there I wanted to ask if anybody got HDMI-CEC to work with their Orange Pi Lite. The data sheet says its supported, but I can't get it to work with Armbian. What I tried till now is installing cec-utils with all dependencies and running "cec-client -l", hoping it would work out-of-the-box: root@orangepilite:~# cec-client -l Found devices: NONE Tried different cables and HDMI Ports. CEC is enabled in the TV (Samsung). After a bit of googling (and trying some stuff applying to the RPi) I am now thinking that maybe the kernel hasn't got CEC support compiled in...? root@orangepilite:~# uname -a Linux orangepilite 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:…

Hi, I thought I'd share this in case anyone else is in the same situation as I. I've been trying to get my Orange Pi Lite to boot the latest (Aug 26 2021) images. I've tried Focal, Bullseye and Hirsute, and the Lite doesn't seem to care for any of them. "Armbian_21.02.1_Orangepilite_buster_current_5.10.12_desktop" from the Archive section does boot, as do the versions of Ubuntu and Debian from the Orange Pi website. Perhaps if I had a serial terminal connected I would be able to troubleshoot this, but I don't yet. I'm using a Sandisk Ultra A1 64Gb and I'm monitoring my power supply with my oscilloscope and haven't noticed any dips belo…

Hello, I installed Armbian (image from here https://www.armbian.com/orange-pi-lite/ [Buster / mainline based kernel 5.4.y]). After booting on OPi Lite everithing works fine. I have updated and upgraded OS. Reboot, shutdown and again turn on the board works just fine. I decided to download desktop for this image. Desktop was downloaded and installed successfully (with armbian-config). Everything works fine. After reboot, shutdown, turn off by unplugging the cable, Armbian on my OPi Lite does not wake up anymore. When I will load this image again, everything works fine by the time I will download and install desktop and turn off the board. I have tried other di…

Hi, root@orangepilite:~# armbianmonitor -u System diagnosis information will now be uploaded to Please post the URL in the forum where you've been asked for. I'm trying to connect my PI board to my smartphone's phone hotspot. I tried with different phones (ASUS Zenfon, Huawei P10, iPhone 11) - "nmcli dev wifi" does not display my hotspots, however nearby computers and the phones themselves do see the hotspots. The PI finds many wifi networks around and use one of them w/o issues: root@orangepilite:~# nmcli dev wifi IN-USE SSID MODE CHAN RATE SIGNAL BARS SECURITY * fbk.info Infra 6 270 Mbit/…

My new Orange Pi Lite can't connect to WiFi networks through internal WiFi adapter (RTL8189FTV) It tries to connect (putting interface...) then very long validating authentification and "Bad password"! But password is right! I tried two WiFi networks with different passwords, but Pi always showed "bad password" Both networks have WPA2-PSK security I set up WPA1/2 hex the WPA2 passphrase but it gave nothing! Please, help me! (Running latest Armbian (3.4 kernel)

My Orange Pi Lite + octoprint often freeze during a print. I noticed that when it happens I can not access either the web panel nor in ssh. I believe that it detaches from wifi and go into freeze. I have already ruled out power supply problems and overheating. Someone can help me?My image is: Armbian_5.25_Orangepilite_Ubuntu_xenial. Here is a screenshot of the statistics: Thanks!

Hello, this is not a big problem, but for me makes a board useless I use orange pi to control ralays thru GPIOs it works flawless on Orange PI PC, PC+, One so I decided to buy Orange PI Lite and I discovered that all gpio are set to high for half a second and then back to low, while unit power up or restarts. Just like an internet router It do that even without a SD card, that points this is coded into U-Boot. Any idea how to fix that?

Hello, can somebody from developers add next to KERNEL_TARGET for Orange Pi Lite in the build system please ? Regards

hi good night i have an orange pi lite, i want to use the (lcd ili9341 3.2 model MSP3218) touch screen and how the installation connections i don't know are correct in these connections in gpios and why my pc broke and qr use orange as desktop i need your help. I will be grateful. I want to connect to the retrorange pi 4.2 system how do I install lcd 3.2 on orange lite? https://mobile4dev.blogspot.com/2017/09/orange-pi-pc-tft-ili9341.html?fbclid=IwAR2h4HLkaBtLA7W5cfXobFbvFkZory0Wznvnju6fMrYzOcDVe1k7oBTwwRw

Hi ! I am using Armbian_5.65_Orangepilite_Debian_stretch_next_4.14.78armbian deb stretch image on orange pi lite. Its working great for the most part, but it misses the starting portion of the audio. I have installed snips voice assistant on it and for some reason the speaker does not produce the confirmation sound output on hotword detection. But plays rest of the sound outputs after that for another 5 seconds or so. Missing the confirmation sound from a smart speaker is really annoying. Is that a bug? Is there a possible workaround? Is any way this can be solved properly? Please point me in the right direction

Does anyone have a countermeasure using Onboard Wifi of Orange Pi Lite?

Hello, and sorry for my English. I install in my orange pi lite the armbian, but I can't config my TFT 7" correctly. The problem is that part of de left size of the screen is hidden and the botton size also. I tray to config with h3disp but depence of the config nothing happens or the screen became red. If I connect by ssh all is correct only is when conect the hdmi. Thank you

Hi All Please can someone assist me. I'm at my wits end here. I have an Orange Pi Lite running Armbian 5.30 desktop edition. I want to rotate the display 90deg. I have had no luck with xrandr as it lists the display as 'default' and not a specific output and this seems to cause a problem. The option to rotate the display is also not available in the display manager. Thanks in advance.

Hi there, when I run command "sudo shutdown -r now" (or sudo reboot) my orange pi shuts down instead of reboot. Why this happens and how to correct it please? Thank you. My armbian: Linux orangepilite 3.4.113-sun8i #10 SMP PREEMPT Tue Jan 24 02:57:18 CET 2017 armv7l GNU/Linux

Hi All I'm having some problem with a fresh install of version 5.30 but had the same problem with 5.27 on my Orange Pi Lite. On reboot, I can SSH into the device with no problems. but after a while connection hangs. If I wait a while after a reboot I can't SSH into the device either. I also can't ping the device after a while. Using the network manager, if I disable and then enable the wifi then everything works for a while. I have checked that the power Managment of the wifi is off. The whole time I can still browse the internet from the device with no problems. Any ideas on where to look …

Hello, I recently bought an Orange PI Lite and wanted to connect it to my WiFi (WPA2 - Personnal) to run a CUPS server. So I connected it to my computer via the serial pins and tried to connect it to my network using nmtui. That looked like it worked well if only a bit laggy at first. But after rebooting it i noticed it was totally unreachable from any other device on the network. So I started pinging everything and started noticing weird stuff : After a reboot Nothing can ping the orange pi unless he pinged them first. When pinging another device from the pi, the first few packets are lost and all following are ~1ms. …

Hi, I have a problem with the wifi connection of the Orange Pi Lite when I connect a HDMI device and switch it on. It is not possible to get the wifi working. I have the same auth. error message like many others here too. But the wifi works well without HDMI device or when the device is off. I have tested the last debian and ubuntu server version and mainline. Thanks for helping

I am a former Dietpi singer of praises (aka as Igor calls us evangelists[not anymore] will now refer to it as the other distro or dp I suppose)...until they kyboshed the armbian based dp images for the orange pi series of SBC's...since then...have attempted to go back and forth with varying success (mostly failures) Going to bite the bullet and go full armbian...been battling getting good wifi connectivity (using my Orange Pi Lite boards as octoprint servers for my 3D printers) After building my own hybrid armbian/dp crossbreed distro for Orange Pi Lite and getting it successfully upgraded to their V6.9 well...it started flipping out, so gonna come…

It used to function fine, however after not using it for awhile it has quit working. It starts booting normally, then hangs with what's visible on the screen being a bunch of systemd messages, with the last being either something about system variables or mounting FUSE file filesystem, when it's the latter it's followed up with a kernel panic. I've reflashed several times using both the server and desktop images freshly downloaded, no difference. The power supply I'm using worked before, as did the SD card. Unfortunately I have no way of showing you system logs or such for the time being. Any help would be appreciated.

Hi, I have two OrangePi Lite running side by side. After working fine for about 8 months both started to experience same issue with wireless: The board works randomly for few hours or few days and then looses wireless connection. When this happens reboot does not help as then issue occurs immediately after the boot. Unplugging and replugging power source resolves that for a while and then happens again I suspect it may not be related to a hardware issue or wireless hotspot, as I have at least 3 other clients that continue to work fine. Searching for it on the internet brought this issue with Raspberry Pi: https://github.com/raspbe…

There is problem with the internal wifi on Orange Pi Lite and Armbian 5.20 (5.16 too). I installed tshark (and tcpdump) and try to capture wifi packets in monitor mode. Without success. What's better. Aircrack-ng works flawlessly. I think, pcap library has a problem with switching the device to monitor mode. "dumpcap: The capture session could not be initiated on interface 'wlan0' (wlan0: SIOCGIWPRIV: Argument list too long)." 'iwpriv' command runs without error, but the private command list is really long. Buffer too small?? Dumpcap run with no errors on external USB wifi dongle (TP-Link TL-WN722N), so I think problem is in firmware of internal wlan chip…

Good afternoon. I don't know how to solve a small problem. There is Orange Pi Lite. It runs its own program. The program uses spi-dev and display. You need to compile drivers for the network card. And then a problem arose. I cannot install linux-headers-current-sunxi on a working distribution (the latest one available on the website Armbian_23.02.2 5.15.93 ). And if you set “Community maintained”, then it is impossible to enable spi-dev and the display (Arbian-Config is missing in the repository) How to solve this problem?

Can someone recommend a good & cheap heatsink for the Lite2 from Aliexpress?

Recently I tested armbian stretch for orange pi lite2. If there is not other task except system, there work fine. But if there are some high cpu tasks, such as unzip, the system load will go high, and not go to lower level when task done. When the system load is higher than 4, the response of the system is laggy, when go higher, the system will go no response. I use uptime to test the system load, when boot, the 1min load will be at 3.xx and go down slowly. When no task, the load will lower than 0.5.

hdparm -t gives only 2-3MB/s for the internal mmc card. Any ideas? The card does over 80MB/s on my workstation.

Hi! I use this board since jun/2019 with Armbian 5.90 and kernel 5.1.15 (all OK except HDMI audio). In these 6 months tried to update kernel image few times, 5.2.x some months ago and now 5.5.0, but not more 1920x1080 support, the maximum is 1280x1024. Xrandr not show as supported mode anymore, whats happen? This is related to u-boot? I think can not read EDID, because no monitor model name is shown. Another question is, now in 5.5.x I can see HDMI audio device, but still can't listen, what left to be developed?

Hello Armbian team, I must start by thanking you for the effort you put into Armbian and making it possible for us to get the best of our boards. Your work is appreciated! The problem that I have been facing is that my OPI lite 2 functions correctly when it boots, but after a while I see a couple of sunxi-mmc errors in the logs and the filesystem becomes inaccessible and the board unusable. The log entries look like this: [ 750.827959] sunxi-mmc 4020000.mmc: data error, sending stop command [ 751.824422] sunxi-mmc 4020000.mmc: send stop command failed I cannot pinpoint the source of the problem as multiple issues seem to play a role in the…

Thank you for bringing USB3 to life on the lite2 again!

Hi, I recently read from github testings of orange pi lite2 testing that wireless is working. But I download from the official website of https://dl.armbian.com/orangepilite2/Debian_stretch_dev_nightly.7z(built 0824) and burn it, it starts, but the wireless is missing. I also read that the firmware added ap6255 wireless driver, so I download https://beta.armbian.com/pool/main/a/armbian-firmware-full/armbian-firmware-full_5.59.180915_all.deb and installed it. After reboot, the wireless is still missing. So the support of wireless is built-in or usb? Should I build armbian myself with the lastest code to support the built-in wireless? Thank you.

I cannot get the screen to rotate 90 or 270 degrees. Inverting it works like it should, but not "sideways". uname -a: Linux orangepilite2 5.4.20-sunxi64 #20.02.1 SMP Mon Feb 17 02:37:37 CET 2020 aarch64 GNU/Linux xrandr --version: xrandr program version 1.5.0 xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192 HDMI-1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.00* 800x600 60.32 56.25 848x480 60.00 640x480 59.94 /etc/X11/xorg.conf.d/01-armbian-defaults.conf: Section "Monitor" Identifier "Monitor0" Option "DPMS" "false" Option "Rotate" "right" EndSection Section "Server…

As soon as I installed the latest version of the Wheezy I have found that there is some problem with an USB. When I start my Orange PI I can see that USB devices are power supplied from the bus only first a few seconds (when the bootloader is active I guess) and then being switched off. When I plug an USB device and supply it externally then it seems to be working well. My question is: how to switch on power supply of the USB port on my Orange PI? I have read a number of linux forums and found nothing. Very promising seems a command echo on > /sys/bus/usb/devices/usb1/power/level or similar but unfortunately it has no effect. Any hint, guys? Thanks a lot. Radek

Hi! I'm using Orange Pi Mini with Armbian_4.2_Orangepi_Debian_jessie_4.1.6. AP mode seems not to work as manual. hostapd-rt and hostapd.conf-rt seems better but I cannot find the AP. Please advise me! Thanks in advance. ----------------------------------------------------------------------------------------- FYI, root@orangepi:~# lsmod Module Size Used by r8188eu 396949 0 evbug 1484 0 evdev 9340 0 sun4i_ts 3722 0 root@orangepi:~# hostapd /etc/hostapd.conf Configuration file: /etc/hostapd.conf nl80211: Driver does not support authentication/association or connec…

Hello, I have a Orange Pi One Plus and i install Armbian image but the ethernet doesnt work. I dont know how fix it. I have search on other post but i cant resolve it. Thanks for your replies!

Hi, I have been messing around with an Orange Pi One Board for a day or 2 now. So far the only distro that works has been yours. But I have the weirdest thing when I apply an update. Excuting apt-get update actually causes the machine to lose power completly. I have been looking at more data this is what I have. After and before the crash. Last freeze with htop analyzing. Am I missing something? I don't see a good reason for this to happen. Is there a common method to fix this if it is a known issue?

I have 2 boards for a long time, an Orange Pi One and Orange Pi PC... Have used armbian older versions for a long time, after almost an all year without using then i have downloaded and installed on both memory cards the new version 4.14 (last version on June 16). My Orange Pi PC is fine, works nice and smoth... But the Orange Pi One dont give me any light (red or green) on the board!!! I tryed to use the OS for PC on the One and its give me green light but dont give video signal... To test the board itself, downloaded and tested a few other OS, from Orange Pi site... And all other OSs from there worked just fine on my One... Turned on leds and give me video s…

Hello! I recently bought a generic Waveshare 800x480 HDMI (B) USB Touchscreen (rev 3.0), and I'm having problems to make it work properly on Armbian. After a long research, I ended up realizing it's a common problem, and yet I haven't been able to find a solution. It seems there was a patch somewhere, but that link is not available anymore. I'm using the Armbian Desktop 5.31 , running on an Orange Pi One. I've already set it up using h3disp -m 800x480 -d, and tried everything but it won't work. Vertical resolution seems to be right, but horizontal only fits around 3/4 of screen and it's noisy (the same problem everyone seems to have). I have tried this with my P…

Hello everyone, this is my first post so please be patient. I am using armbian for a long time on my cubietruck, but this time I got a problem with my Orange Pi One. I have build a Embedded Cluster [1] out of a cubietruck, 5 Orange Pi PC and one Orange Pi One system. Since yesterday I have modified my cluster chassis. Maybe but just maybe a short circuit happened on my OPiOne because of some assembly issues I had during it's installation. The problem is that it OPiOne does not boot any more. The red and green LED are still turned off. The two LED'S of the ethernet port are always switched on. Nothing to see on a screen attached to the HDMI port. It a…

Hello. I am using baresip for SIP communication. I have faced a problems with audio USB adapter (http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141629380416) with C-media chip. I have set it as default sound card. I make a call using baresip. Until I answer the call on another device it works, it rings. But when I answer, kernel errors occurs and Orange Pi hangs (cannot do anything): Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.378730] sunxi oops: enable sdcard JTAG interface Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.380906] sunxi oops: cpu frequency: 1008 MHz Message from syslogd@localhost at…

Hardware: Orange Pi One with a CF-WU810N (Realtek 8188eus) USB WiFi dongle Software: [MAINLINE] - ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi Goal: Configure and run the Orange Pi One HEADLESS (using a physical ethernet during initial configuration) I've been away from armbian for awhile, so it looks like I've got some catching up to do. I'm running a headless Orange Pi One with a CF-WU810N (Realtek 8188eus) USB dongle. Since it's headless I use a physical ethernet cable to get access and make initial configuration. From the documentation (https://docs.armbian.com/User-Guide_Getting-Started/#how-to-connect-to-wireles…

I have a Lenovo Mini USB keyboard N5901. It doesn't seem to work with the following image: Armbian_5.20_Orangepione_Debian_jessie_3.4.112 Can anyone assist on what I should do to enable the keyboard?

Hello, i am having a problem with my Orange Pi the download speed is very slow. In Deluge and by wget i get normal DL speed around 9Mb/s (i have a 10Mb internet). But in JDownloader and in builit-in web browser i get around 100Kb/s. Any idea how to solve this issue? I want to make a download server using OPi but this issue is stopping me from doing that. I am running the newest Armbian Desktop

Hi everyone, today I notice that my orange Pi one stopped (crashed) yesterday, how to prevent this next time ? Is the watchdog a solution to the problem? or please advice are there any additional parameters or details I need to know for using watchdog ?

Hello, I have red, that WiFi card built-in Orange Pi Lite (RTL8189FTV) could make troubles (drivers), so I wonder - maybe will be better to buy Orange Pi One and WiFi dongle (a well tested one, with non-problem chipset) Which WiFi dongle would you recommend for Orange Pi One?

Hello. First of all sorry if this isn't a place to post this. I recently bought an orange pi one. And I'm using Armbian OS. (Latest version downloaded from Armbian website) But there seems to be a problem with WiFi and i searched all over the internet and i didn't found anything about it. So here is how it was: First time that i wrote the Armbian OS on the SD card and configured it (as said by the Armbian website I didn't connected the WiFi dongle) and after doing those stuff I did connected the WiFi dongle to it. It worked fine, but after some mins both LEDs were on. And nothing was working. I did the things I said above many times and the same happend. And once I d…

Hi there, As the topic title says,... Is there any available option to install/setup Domoticz server onto Orange Pi Box using Armbian Desktop or Server version? Thank you! Kind regards

Hi all, Orange Pi One Armbian_20.02.0-rc1_Orangepione_bionic_current_5.4.14 Enable w1-gpio /boot/ambianEnv.txt: overlays=w1-gpio param_w1_pin=PD14 param_w1_pin_int_pullup=1 dmesg | grep -E 'w1|wire' [ 5.271798] Driver for 1-wire Dallas network protocol. [ 5.304021] gpio-110 (onewire@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file What and where else needs to be done?

Hello all guys, I tested my orange pi one and it is free from the overvoltage "defect" related to the CPU voltage regulator. The multimeter reports the expected 1.1 and 1.3 voltages. I decided to do some tests to find the highest frequency it can run stable at its lowest voltage of 1.1 volts. I found something odd. This is the dvfs table I'm using now: [dvfs_table] pmuic_type = 1 pmu_gpio0 = port:PL06<1><1><2><1> pmu_level0 = 1100 pmu_level1 = 1100 extremity_freq = 1200000000 max_freq = 1200000000 min_freq = 648000000 LV_count = 2 LV1_freq = 1200000000 LV1_volt = 1100 LV2_freq = 648000000 LV2_volt = 1100 If you're skilled with script.fe…

http://www.fsfla.org/ikiwiki/selibre/linux-libre/ I expect this is the software. Free software is software you may use, share, modify and redistribute. To my knowledge orange pi one has an armv7 cpu. And the gpu is the same as on a pinephone. On this forum I was told command apt purge iozone3 armbian-firmware might turn armbian into a free software system. There is an armv7 libre linux kernel, which to some extend supports mali gpus. I want to test the libre linux kernel on an orange pi one computer, to get to know how well a Mali 400 MP2 runs on free software. Maybe it can give a streak of how well the pinephone's …

Currently, There is no mainline release for Orange Pi One. The only release of mainline is in nightly build folder and the kernel version is v4.11.8, which doesn't work SPI chipselect. On armbian latest source compiled image, v4.13.9, SPI problem is solved. Do you have any plan to release official mainline image for Orange Pi One? Thank you very much.

Hi everyone, I bought an Orange Pi oneas a cheap replacement for the unobtainable Raspberry Pi Zero for a little Emulation project. Right now I don't know if it was the right decision:) I wanted to add a waveshare 3.5" display to the orange pi, but I don't even get there. I downloaded the armbian distribution v5.10 legacy Jessy desktop. After the start of the desktop, icons, the taskbar and open windows disappear at random, icons return but the taskbar does not, The desktop is unusable. A similar problem happens in the console, I don't see the cursor where I'm typing. On the command line, thats acceptable but using an editor like nano I have no idea where I am. …