Allwinner sunxi

Hello, actually i have "Bananian" with the kernel "3.4.113-bananian", and I would like to switch to the Armbian mainline kernel! My problem / question is how does it work with the GPIO in the mainline kernel? I use these commands under the legacy kernel... (I use the modified WiringPI from LeMaker) echo "17" > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio17/direction echo "1" > /sys/class/gpio17/value But these unfortunately no longer work under the mainline kernel! I don't understand how i calculate now the right GPIO Pin. (http://linux-sunxi.org/GPIO#Accessing_the_GPIO_pins_through_sysfs_with_mainline_k…

Hi. I'd want to set a custom MAC address to my cb2. I set the static mac address in u-boot environment variable ethaddr. If i print the environment (with "printenv command" i find it right there but when the system starts and i go through ifconfig i can see eth0 has a different MAC. Any suggestion on how to get MAC from u-boot? I'm on Armbian 5.20 legacy kernel. Thank you

Hi, I am totally new to Linux, but already managed to run OMV on my Banana Pi M1+ with Plex and other services I wanted on Armbian. Now I tried to run Kodi, so it could serve me both as NAS and HTPC. Firstly, I have installed xorg, then lightdm and set it up for autologin, which is working correctly. Then, I have installed Kodi 16 from git, but only gray box appears and then vanishes and screen stays black. My first impression was it is lacking GL drivers, so I have followed this tutorial: https://forum.armbian.com/index. ... pi-orangepi-pc-etc/, tested and everything seemed to be ok. I installed Emilia Pinball to check additionally - it renders correctly. Still, when …

Hi, I have a Cubietruck and install Armbian_5.38_Cubietruck_Debian_stretch_next_4.14.14.img from https://www.armbian.com/cubietruck/. Copied with Etcher the unpacked .img-File to a SanDisk Ultra 32GB micro SD HC1. But no system comes up Last message U-Boot 2017,14-armbian (Jan 24 2018 ... . . Loading Device Tree to 49ab5000, end 49b29fff ... OK Starting Kernel No blinking cursour on top of the left side. Nothing go's on! System with Armbian_5.37_Cubieboard2_Debian_stretch_next_4.14.14.img works, but no network with armbian-config, neither static nor DHCP, can configure. (dnsmasq.service not found) LAN-Cable ist pluged. …

Hi, I was wondering if anyone was having issues with the ethernet port using the legacy kernel ? It does seem to kind of work ... it will get DHCP from the router and configure the routing tables etc but after that it goes wonky. When I do a ping test from the router I get "50/50 transmitted, 15/50 received, 70% loss". A ping test from the opi-win to the router gets a similar result. If I try a ping/ssh from a PC connected to the router I get a 95% packet loss Everything else seems to work fine ... HDMI, USB, WiFi (AP/STA modes) which is really, really nice. Thanks TB

Hi I am using an OrangePi Zero 2+ with AllWinner H3 and i need both uart. I enable them with armbian-config and on pins Uart2 on pins 8 and 10 work fine bat uart1 on pins 11, 13 don't. The pin on this board is not the same as orangepi zero? I mast make some setup to make uart1 to work? auto@orangepizeroplus2-h3:~$ uname -a Linux orangepizeroplus2-h3 5.9.14-sunxi #20.11.3 SMP Fri Dec 11 20:31:12 CET 2020 armv7l armv7l armv7l GNU/Linux auto@orangepizeroplus2-h3:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=i2c1 uart1 uart2 uart3 usbhost2 usbhost3 …

I have Orange Pi Zero and plugged bad USB modem with power problems. Some moment modem have power problem and disconnect from board. USB port in Orange PI disabled after it - lsusb show one of two board's USB hub is absent After reinstall image in this board, USB hub works well. I think, USB hub disabled by OS when USB port has errors. Let me now. how to enabled USB hub without OS reinstall?

Hello! I'm using Armbian Stretch for 1080P Pinebook A64. I've installed Armbian Stretch about 2 months ago, when it was still "Unsupported" and in-development. Now, however, it's supported. Currently, I'm on Armbian Stretch 5.60 and dev branch. I would like to update to 5.69 and next branch. However, from armbian-config, I'm only able to go from stable to nightly build (5.68, but still dev branch). Moreover, I can't select next kernel from Other menu. Is there a way to switch branches (barring re-flashing from latest image)?

Good day! I've had the Nanopi Neo2 v1.0 for sometime now, used for mostly for NAS solution. the v1.0 is the one being carried by my supplier here. No v1.1 yet Lately I installed armbian monitor to monitor system resources. Then I stumbled upon the min and max frequency when I checked using # cpufreq-info -p 408000 816000 ondemand I've read on some internet writeups that one can set the max frequency to 1008000 tried editing the cpufrequtils scaling_max_freq scaling_available_frequencies scaling_setspeed I was able to lower the minimum frequency to 120000 using the following entry…

Hello, everybody. I have an orange pi pc2 device with armbian-release on it: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.46 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=custom BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image I was install my nodejs app on it, which lunch on start up. Device now is remote. Everything was fine, but now i have a look at log (my nodejs log) and see strange reboots after that my app dose not lunch. When I ask people (device is remote and is ON) do OUT/IN power on it - after that everesing fine until the another randoml…

On a CB1.... cubie@cubieboard:~$ uname -a Linux cubieboard 4.5.2-sunxi #11 SMP Thu Apr 28 21:53:25 CEST 2016 armv7l GNU/Linux cubie@cubieboard:~$ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 8.4 (jessie) Release: 8.4 Codename: jessie cubie@cubieboard:~$ ... I'm trying to use the gpio pins I set up in script.bin with this configuration: No other peripherals are using those pins that are configured in my fex file. A scan of the DTS file also shows nothing using those pins. When I enable pin 1 via: the gpio1 device shows up. When I do the network interface stops communicating. The sy…

Hi there, 2 days ago I did apt update + apt upgrade on my OPi3, everything fine. Yesterday I did a system reboot (as suggested "kernel changed"), then Eth port went dead. No even ARP works (ARPING). Have tried: - ifconfig shows correct values, - ethtool shows 1Gbps FDX connection, also same on router (OpenWRT TL-WR1043ND w 18.06 software), - changed eth cable, - on other OPi connected to same switch / router (also went dead) depowering device helped, but not on OPi3, - ARP shows MAC/IP not resolved, - WiFi (configured as AP) looks working. - also changed port on router and did power cycle device, nothing helps. - on r…

Hi! I have ARMBIAN 5.31 on my Banana Pi m1 and need some help. Early I used wheezy and mount webdav disk with davfs2 in fstab, but after I installed jessie fstab dont mount any davfs2 disk. Besides I have another problem: I use davfs2 to backup some video and photos to cloud storage throw webdav, and I have mistakes on large files (files much bigger then free space in /var/cache). Davfs2 send files in cache folder first (/var/cache/davfs2 by default) and then to webdav disk, so I have to use another disk with enough free space (sda1 in my case). When I was on wheezy I just point cache dir to sda in dafs2.config (cache_dir option) and all be OK, but i…

Hi every body, Tanks igor for your great job with your linux versions for cubietruck. I installed jessie with kernel 3.4. I'm trying to make a media server with minidlna. Cubietruck is connected to the router with ethernet when i'm at home and minidlna stream fine. I sucessfully installed hostapd with your interfaces.hostapd file. Ethernet plugged, i can connect to wlan0 and access to minidlna. My problem is when ethernet is unplugged and i reboot the cubietruck. I cannot access to minidlna via wlan0. I set network_interface=br0 in minidlna configuration. Do i need to manually configure dhcp or something like that?

Old post below, here is what I found out thanks to some help from linux-sunxi IRC, I think this is a bug in the ondemand governor When using ASIX AX88772B USB to ethernet adapter and the cpu-governor is on ondemand, transfer speed is very slow. If governor is set to conservative or performance (yes that's right) speed is ok, 50 Mbit at least. So the problem has nothing to do with cpu speed as such (it's working @ steady 480Mhz and @ steady 1200Mhz) for now I'll stick with conservative as I don't want my board to burn up, but It would be nice if someone could take a look at that ondemand governor. Additional info: …

I want to use an ESP-12F to add wireless to my NanoPi Neo, but I don't think the Neo has broken out all the connections I'd need. Hackaday desctibes how to interface a Raspberry Pi B+ to an ESP-12F (https://hackaday.io/project/8678/instructions), but the Neo seems to lack some of the required pins. I like this idea since I've liked the performance and ability of every esp8266 system I've used. Their wifi network is solid, and they're low cost. Is this a lost cause or is it possible? Or perhaps this is a dumb idea? I'm not sure how well it'll perform vs a usb wifi modules, but the idea has captured my imagination.

I am use igors lib to get an suffucently patches kernel source for bana Pi R1 and for test builds i use this script for my unattened kernel builds. This allows directly install an fresh kernel and make an backup of the old kernel. my custom kernel .config is then at $REL stored and used . usage path : run igors compile.sh , wait till the source download done , do an CRTL-C once the kernel wants to compile from his lib then i.e : fw1 /t/GIT/output/linux-mainline # cp .config /t/GIT/.test5 fw1 /t/GIT/output/linux-mainline # /t/GIT/build.sh Usage: /t/GIT/build.sh {build|timestamp|clean|install|ins…

Hi everyone, I want to create an USB device, for this i am following this tutorial : gadgetfs. It works fine, but when i want to have an endpoint superior to 4, i cannot. I just changed to Unfortunately, in the folder created i have only this files : ep1in ep1out ep2in ep2out ep3in ep3out ep4in ep4out musb-hdrc I thought a usb device can have 32 endpoints. So, is it possible to have an extra endpoint ? And i have an extra question, as a kernel noob, I don't fully understand how this guy came out with thi…

Like most people that have consumer ipv6 service, I have NATted ipv4 + global ipv6. I'm trying to get my v4 to be a static address and my v6 to be slaac with privext 2. However if I try to set this, I end up with the ipv6 configuration not enabled. As a workaround, I've set both v4 + v6 static, but would really like to get slaac working, as my global /64 has not changed to date but is not guaranteed to remain the same. This works: iface wlan0 inet static address 192.168.0.100 netmask 255.255.255.0 gateway 192.168.0.1 wpa-ssid my-essid wpa-psk <my-hash-here> iface wlan0 inet6 static address 240x:xx:yy:zz:dead:beef:cafe:babe n…

Hi Friends, on Banian I was using "xset dmps force off" and "xset dpms force on" to switch display off and on as I need it. Tryed to use this commands in terminal with armbian but nothing happens. I'm using LeMakers 5" LCD RGB Display with PCAP Touch. Armbian is 5.24 jessi with desktop and 4.8.12 Kernel. Has anyone an Idea, how to turn off and on display form terminal? Yours, Martin

I have tried the image for Buster from the Download page for OrangePi PC Plus, and also built new images from current Git repo. In all cases the device bootloops when it tries to start the kernel. The image from the OrangePi website works ok. This looks like a similar issue as experienced recently with CubieTruck and BananaPi A20 boards (https://armbian.atlassian.net/browse/AR-749) which was fixed with a workaround (https://github.com/armbian/build/pull/2963) Is it possibly the same / similar underlying problem?

Hi Igor, is there a reason why the "killall" binary is missing in /usr/bin? Some of our applications use this file to kill servers... Can you add it in the next version? Thanks. Steffen

Hello, I install Armbian on my Orange Pi Win Plus, i use the image for Orange PI Win i have the boot starter after nothing, someone can help thank you

Hi, I bought about a year ago an orange pi plus. Just a few weeks ago, i tryed the new distro's I love to have debian on the board. And like your distro verry much. I have 2 problems: 1) If i download the file for orangepiplus, the board does nothing. No leds go on, no grafics on screen, nothing I also tryed at home compiling it myself. The result is the same nothing. My Orange Pi Plus has an H3 processor - it is one of the first OrangePi Plus boards. (Is this an error in your piplus distro - just because loborus for piplus works) 2) If i download the orangepih3 file, the board will startup. I can not run sata-nand, because i get an error - abo…

After I copied the original OS from the SD card to an external usb HDD and make the Orange PI PC boot from it, mouse and keyboard suddenly don't work anymore on xfce. Strangely the keyboard still works with CLI. Also i got this error when I start armbianmonitor -u : root@orangepipc:~# armbianmonitor -u System diagnosis information will now be uploaded to /usr/bin/armbianmonitor: line 388: read: read error: 0: Invalid argument /usr/bin/armbianmonitor: line 389: [: -ge: unary operator expected /usr/bin/armbianmonitor: line 388: read: read error: 0: Invalid argument /usr/bin/armbianmonitor: line 389: [: -ge: unary operator expected /usr/bin/armbianmonit…

hi all I'm the owner of a Cubieboard1 (A10) running Armbian 5.31 Debian Jessie, kernel 4.11.5 (recently upgraded) I'm not quite sure when it happened (normally it stays up&running continuously), but recently I needed to reboot it and it simply shuts down, with no subsequent boot I've tried multiple times, upgraded the kernel, tried both via GUI and trough cli,.... no way: it simply stops, and I need to push the power on button I've not been able to find any glimpdr on the logs Obiouvsly it is quite annoying, especially for remote management Do you have any idea on the possible causes, troubleshooting etc…

I have board which has 2 slaves on the SPI bus, requiring ce0 and ce1. My system: Armbian 23.8.1 Bookworm with Linux 6.1.47-current-sunxi I applied overlays: spi-add-cs1 and spi-spidev, there's an spi in the system. As soon as I apply spi-double-spidev-bus.dts, the spi disappears. Скрытый текст /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&spi0>; __overlay__ { #address-cells = <1>; #size-cells = <…

Hi, I installed the Xenial Mainline 4.6.7 image for the Orange PI PC+. That works fine and I can boot into the system. But when I do an apt-get update & upgrade, the system hangs afterwards during the boot. At the first boot after the upgrade the system hangs after "Started udev Coldplug all Devices.". The second boot a kernel panic occurs. See http://pastebin.com/47t45ujr Is this a known problem? Regards

Hello all, i can't see Banana Pi M1 on the available downloads on Armbian site where can i find it? if that exists of couse. Thanks

I have a solar application for PC, so my goal is to reduce the power consumption in idle as much as possible. How would one go about this with the latest armbian distros?

Hi, I installed pyA20 on my Orange pi PC2 and running one of the test files I'm getting segmentation fault. I am running ARMBIAN 5.34.171029 nightly Ubuntu 16.04.3 LTS. Can somebody help me troubleshoot the problem? Thanks,

6.960880] zram1: detected capacity change from 0 to 506638336 [ 7.108492] asoc-simple-card soc:sound: i2s-hifi <-> 1c22800.i2s mapping ok [ 7.821162] random: crng init done [ 7.821171] random: 7 urandom warning(s) missed due to ratelimiting [ 7.897054] Adding 494760k swap on /dev/zram1. Priority:5 extents:1 across:494760k SSFS [ 7.995324] zram0: detected capacity change from 0 to 52428800 [ 8.134498] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard [ 11.299194] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.1:01] driver [Generic PHY] [ 11.299222] dwmac-sun8i 1c30000.ethernet eth0: phy: setting supported 00,00000000,000062cf advert…

Hi, I accidentally deleted files containing default repositories - Armbian Server 5.30 stable Ubuntu 16.04.3 LTS. So my question how to restore the default repositories of armbian ?... I found this page but I'm not sure what to choose Link: Ubuntu sources list generator Hardware: Orange Pi One OS: Armbian Server 5.30 Ubuntu Xenial 16.04.3 LTS

Hello, Hello, I have connected a pcf6523 RTC module to my OrangePI plus 2E and I can not get it to work. The i2cdetect -y 0 command gives me the following answer: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- 04 -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 21 22 23 24 -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: 40 41 42 -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- 70: 70 -- -- -- -- -- -- -- The next thing I have to …

CONFIG_BTRFS_FS_CHECK_INTEGRITY is not enabled in config. When I tried to enable it in the armbian build system, I saw the word "DANGEROUS". Is this an unstable (or dangerous) feature ? Should I enabled it and use it ? if not, how to ensure data integrity ?

Hello, I used the Wheesy version for my web server with virtual host that worked. The site is in / var / www / bbp / public_html / Now , I use the Jessy version with the same structure , Apache does appear to me that the page "default". I have no error when validating the virtualhost , I raise apache well and nothing is displayed for the site " bbp / public_html / " I do not understand what can no longer function . Thanks François

First of all, hello to everyone. I'm new to this forum so sorry if my question may look stupid, but i've strolled through the internet far and wide. I cannot find simple(for dummies version) step by step tutorial how to connect TFT waveshare knock-off with XPT2046 controller. Compatible with ADS7846 according to this thread: https://www.raspberrypi.org/forums/viewtopic.php?t=143581 I was able, using info from link below to run command line on legacy kernel. https://kaspars.net/blog/linux/spi-display-orange-pi-zero So i know about reverse SPI connection in orange pi zero. When i tried command: sudo modprobe fbtft_dev…

Hi. I'm using "Orangepi-r1_focal_current_5.8.5" Armbian. I'm connected to it via Wifi. Everything working fine, but after few hours, I notice that it is no longer showing on my network. If I connect by cable I can ssh to it via ethernet without any issue and it stays available for several days without disconnecting. Any idea why this happens? when Wifi disconnects I will have to reboot to show it again. And I am not running any program on it. Is orange pi r1 wifi like orange pi zero wifi suffering from poor software support?

update works on 5.4.28-sunxi64, so for sure kernel issue... I fail to start the nfs-kernel-server on my neo2: ● nfs-server.service - NFS server and services Loaded: loaded (/lib/systemd/system/nfs-server.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2020-06-19 22:50:35 CEST; 57s ago Main PID: 28168 (code=exited, status=1/FAILURE) Jun 19 22:50:35 neo2 systemd[1]: Starting NFS server and services... Jun 19 22:50:35 neo2 rpc.nfsd[28168]: rpc.nfsd: writing fd to kernel failed: errno 111 (Connection refused) Jun 19 22:50:35 neo2 rpc.nfsd[28168]: rpc.nfsd: unable to set any sockets for nfsd Jun 19 22:50:35 neo…

I've managed to get tv-out working on Armbian_5.24_Orangepizero_Ubuntu_xenial_3.4.113 with adding module tv to /etc/modules, but goes out of display. How can I change overscan to fit dispay to screen?

Hello! I've downloaded the current images for BananaPi M1 offered in the site, as "Community Maintained" builds, but none of them is capable of producing video output from HDMI nor composite video. Both the Ubuntu jammy and Debian12 versions lose the video output as soon as the kernel starts to load, after the u-boot screen. I tried the desktop and server images, without any luck. With the older 5.x kernel, the ubuntu-jammy image that I've downloaded before loads fine. I know it's an old board, but it still gives me some amusement time tinkering with it and playing retro games. Anyone experiencing the same problem? Thanks!

Hi, My Armbian Vanilla for Cubieboard1 is working las 2 months... Theres is an iissue with I2c, that I don't know how to avoid or stop Dmesg and syslog are flooded with this message Feb 7 11:09:05 localhost kernel: [172015.158063] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:06 localhost kernel: [172015.688415] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:06 localhost kernel: [172016.158440] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:18 localhost kernel: [172027.837841] i2c i2c-0: master_xfer[0] W, addr=0x34, len=2 Feb 7 11:09:18 localhost kernel: [172028.087760] i2c i2c-0: master_xfer[0] W, addr=0x34, len…

Hi All. First post here (and quite a newbie). I have installed Armbian on my new NanoPi Neo and followed the instructions. It is all booting OK and I now wondering how I can attach a speaker directly to the header 10 LINEOUTR LINE-OUT Right Channel Output 11 LINEOUTL LINE-OUT Left Channel Output 12 GND 0V Will this work? How can I test it as I cannot see it with ALSAMIXER. TIA.

I successfully installed Armbian Focal¹ on my Neo Core 2 with MiniShield² and SSD. I find no issues after booting boot from SD-card. But I fail to boot from eMMC with System on SATA using nand-sata-install: In the serial console i see the boot process to stick after «Started udev Kernel Device Manager». Any hints how I can unblock from here? [...] U-Boot 2020.04-armbian (Sep 02 2020 - 09:50:54 +0200) Allwinner Technology CPU: Allwinner H5 (SUN50I) Model: FriendlyARM NanoPi NEO Core 2 DRAM: 512 MiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In: serial Out: serial Err: serial Net: …

Hello, I have the LIME2 board from Olimex (A20 SoC). I tried writing the image Armbian_5.20_Lime2_Debian_jessie_4.7.3_desktop to an SD card with dd. However, nothing happens when I plug in power (except that a red light near the barrel jack connector turns on). I tried pressing some of the switches (reset, power) but they didn't do anything either. This is the second LIME2 board I have received that just won't turn on. I have also tried with the images recommended by Olimex, to no avail. Is there something special that needs to be done that I'm missing?

I don't know if this is normal. Sorry if this a stupid question, :huh: but I don't know why there are inside of the /boo/bin directory a bananapi.bin and bananapipro.bin but on the /boot directory the image target the bananapi.bin instead of bananapipro.bin. Board: banana pi pro; debian wheezy 4.04.4 (igor image) shows: root@bananapi:/boot# ls -ltr total 12852 -rwxr-xr-x 1 root root 5030568 May 21 21:59 vmlinuz-4.0.4-bananapi -rw-r--r-- 1 root root 1788788 May 21 21:59 System.map-4.0.4-bananapi -rwxr-xr-x 1 root root 95973 May 21 21:59 config-4.0.4-bananapi lrwxrwxrwx 1 root root 28 May 21 22:31 zImage -> /boot/vmlinuz-4.0.4-bananapi drwxr-xr-x 2 root roo…

Hello! My problem is with paying for OrangePi Plus 2 (not E), but I haven't found a suitable section. Dear administrators, please fix the split if I made a big mistake. I was installed image orangepiplus/Bullseye_current (Nov 30, 2022) in eMMC. All works is normal. In armbian-config I was run Firmware (Update all packages and firmware). Afeter this the board are not loading from eMMC or external CD with current image Armbian. The Ubuntu from site orangepi.org the loading is normal. In debug-uart I see a cyclical reboot with: <0xdd>!␊ ␊ <0xea><0xfc>q<0xb9><0xf6>Core: 65 devices, 18 uclasses, devicetree: …

Hello! Need help for installing KODI 16 or 17 on Orange Pi PC on Armbian 5.25 I managed to install KODI 15, but it's old and some of add-ons don't work anymore. When I tried to install KODI 16 I received errors on libcec4 and libshairplay Thank you in advance!

I've been struggling for a while to get raspberry pi HAT type LCD to working. I've been working with loboris images before until recently that I've heard that armbian has cooked a new image for orangepi with newer kernel. In the description of images it is clearly indicated that the image works with small screen lcds which it seems to be true because there is no error when I want to load a notro module and it successfully loads. I've put lcd configurations in /etc/modules but I was not successful. this is the parameters I use in /etc/modules fbtft_device name=flexfb gpios=dc:22,reset:27 speed=48000000 flexfb width=320 height=240 buswidth=8 init=-1,0xCB,0x39,0x2C,0x00…

Hello. I am new to Armbian. My Banana PI M2 (already a disappointment, bad purchase on my part) is up and running but will not reboot all the way. It shuts down but does not restart again. Any ideas how to go about troubleshooting and fixing this? It is a deal breaker for what I planned to be a headless system. It needs to be restartable without physically pulling the plug to do so.

Hi, since one the last two kernel updates I experience random out of memory scenarious on my Cubietruck. Up until then all was fine. When Oom Killer kicks in the following is logged: ........................................ Spoiler Mar 4 06:54:23 cubietruck kernel: [80988.962548] sh invoked oom-killer: gfp_mask=0x24000c0(GFP_KERNEL), nodemask=0, order=2, oom_score_adj=0 Mar 4 06:54:23 cubietruck kernel: [80988.962563] sh cpuset=/ mems_allowed=0 Mar 4 06:54:23 cubietruck kernel: [80988.962584] CPU: 1 PID: 10543 Comm: sh Not tainted 4.9.12-sunxi #4 Mar 4 06:54:23 cubietruck kernel: [80988.962588] Hardware name: Allwinner sun7i (A20) Fam…

Hi you all, I have flashed a good, tested and reliable 32GB SD card with the last build for Orange PI Win (armbian 5.38) and when first updating, it stucks in "waiting for headers" for too long. I have read that this is caused in Linux systems because one installs third party software whose repos take long to answer, but since here it is a first and fresh update, with nothing but armbian inside, I ask myself if it is normal or there is a problem with the servers at this moment. Only apt-get update ca take up to 1h 30 min, so it is really an annoying issue. Is anyone out there experiencing the same problem (and hopefully with a solution) ?? Thank you guys!…

Hi! I had serveral errors with my Cubietruck running Ubuntu 16.04 Vanilla Kernel. The system is installed on a hard-disc. There were some filesystem-error which fsck could repair. But I still have some errors. root@cubianx:~# systemctl --failed UNIT LOAD ACTIVE SUB DESCRIPTION ● apparmor.service loaded failed failed LSB: AppArmor initialization ● systemd-modules-load.service loaded failed failed Load Kernel Modules LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values de…

Hello! Thanks for this great project! I've tried to clean install Armbian 4.2 with 4.1.6 kernel on Cubietrack. I've tried Debian Jessie and Wheezy. I've been waiting up to 5 min, but can't find my Cubietrack in network. Boot hangs on (from serial console): U-Boot SPL 2015.07-dirty (Aug 25 2015 - 19:12:58) DRAM: 2048 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 U-Boot 2015.07-dirty (Aug 25 2015 - 19:12:58 +0200) Allwinner Technology CPU: Allwinner A20 (SUN7I) I2C: ready DRAM: 2 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment Setting up a 1024x768 vga console Error: no valid bmp image at 66000000 In: serial Out: vga Err: v…

Hello I'm investigating update from wheezy to trusty on my OrangePI (A20) based home media server. I'm using custom kernel 3.4.110 with SATA multiplier support. System is on HDD. I had few remarks and issues (part of them were solved but some are not): - Video acceleration was not working out of the box on trusty desktop image but it was solved it by installing "Desktop-extras for Jessie-desktop (sunxi)" - it looks it could be added as default for trusty. But mvp package can't be installed due to depedencies to libs which I did not found in ubuntu reps?! - compositing if OFF in xfce but when I moving windows on the desktop, CPU load is becoming 100% till I stop movi…

Hello fellow Armbianers! I'm using Orange Pi zero. My only complaint is the 30s boot time. Looking at the log files, seems like it only takes 5 seconds to boot once the kernel is loaded. The majority of this 30s is spent in uboot somewhere? Does anyone know how to speed up this boot process? I'm always just booting from SD card, don't need USB boot/network boot, console, or any of that. Thanks!

Dear all, I copied Armbian 4.5 (on cubietruck with kernel 4.3.3) from SD to SSD using the script "nand-sata-install.sh". The resulting system with /boot from SD and rootfs on SSD works fine. However, the "Welcome to Armbian" message generated upon login contains the error message "df: cannot access ‘/dev/sda1’: over-mounted by another device" (see below). It seems to be related to mounting /boot from SD. Do you have any suggestions how to get rid of the "df: cannot access" message ? ____ _ _ _ _ / ___| _| |__ (_) ___| |_ _ __ _ _ ___| | __ | | | | | | '_ \| |/ _ \ __| '__| | | |/ __| |/ / | |__| |_| | |_) | …

Hello, Im using a Orange Pi Zero, running nginx with Nextcloud. Im noticing 99.99% usage on the IO reported by iotop, but disk read and disk write show 0%. Even a refresh on the homepage bumps it up to the top of the IO list. As far as I am informed... isn't kswapd0 supposed to deal with swap memory and go wild when I am about to run out of RAM? I have disabled (hopefully), my swap partition, but I am still getting this. I have commented out the swap line in fstab... htop reports 0KB SWAP. It doesn't seem that I am running out of memory. About 50% of it appears to be free all the time. I am really new to dev boards and such, but this didn't appea…

I noticed that the orange pi win plus does not have a sata port connector. Is there a way to attach a sata ssd/hdd to the orange pi win plus through the gpio pins?

Hello everyone. I have installed the Armbian Xenial Multimedia and desktop usage scenarios on my orange pi pc plus. Setup user and new password successfully. By using the command armbian-config I have solved my keyboard issue and language. Also network Lan0 is ok By typing sudo apt-get update and upgrade my orange is now updated succefully. But how to start the desktop ? I can only see the black screen with prompt command. If I reboot it , after all [ok] ...... I read Ubuntu 16.04.5 LTS orangepipcplus tty1 login ...... Did I do some mistakes?

Hello, I am very sorry that I have to leave the Armbian flock, but the Dietpi-Distro is so much better. It simply boots off the SD-Card on my NanoPi NeoCore and the darned Ethernet simply works; also the DTB overlay files work, so the additional I2C and UART hardware works in Dietpi. And the kernel is 6.x too ! However, the NanoPi Neocore is shipped with an outdated Armbian (using Kernel 4.x) on EMMC. What I now want is to replace the prepared EMMC Armbian distro with whatever is on my SD-Card, but this task is more difficult than I tought. What I would need is to simply copy the whole SD-Card to EMMC, but the recommended "dd if='sdcard...' of='emmc...'...." co…

Dear community, Im trying to get an USB gadget via OTG running on Linux (OrangePI Lite 2). As OPI Lite 2 doesn't support 'USB-UART/Gadget mode' like OPI Zero, I just modify the build config and rebuild kernel by myself as steps shown below. 1. I change the mode of USB from host to otg in the: https://github.com/armbian/build/blob/master/patch/kernel/sunxi-current/board-h6-orangepi-lite2-fix-missing-all.patch 2. I add MODULES_CURRENT="g_serial" & SERIALCON="ttyS0,ttyGS0" to build/config/boards/orangepilite2.conf file. 3. I rebuild the kernel and flashed the new image to sdcard. Unfortunately, I find it…

Hello to everyone , I'm trying to read NMEA messages from GPS receiver via UART . But can't read anything on pins 8,10 & 38,40 .. What coulb be a reason ? GPS receiver is working fine , I can read it via USB-UART converter on the same board ... Thanks in advance ! Here's my system (UARTs are enabled via armbian config utility): root@orangepiprime:/boot# cat armbianEnv.txt verbosity=1 console=both overlay_prefix=sun50i-h5 rootdev=UUID=aca8c4ac-41d0-4e0b-ae7e-1d727baa4d43 rootfstype=ext4 overlays=pps-gpio uart1 uart2 uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u root@orangepiprime:/boot# uname…

I try connect 3.5' LCD screen, but i have error ---------------------------- Jan 4 12:24:38 pls-home kernel: [ 54.977794] fbtft: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.981924] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.982417] fbtft_device: unknown parameter 'gpios' ignored Jan 4 12:24:38 pls-home kernel: [ 54.982696] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 Jan 4 12:24:38 pls-home kernel: [ 54.982947] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 …

1. Orange pi pc cant shut down ,remains blink. 2. Cant eject usb /sda file directory not available. 3.funny with much updates still cant connect to Internet with clearing block interfaces from armbian config.

Hallo, I hope the topic hasn't existed before .. I have an Bananpi M2+ as H5 (64bit). Good Images are OrangePi-PC2 or NanoPi K1 Plus. My problem is, no support of emmc. Are there any known compatible images for the Banana Pi M2 + H5 that work? The NanoPi K1 Plus has problems rebooting and recognizing a keyboard. The OranngeP PC2 works fine, but no emmc support. Thanks and Best wishes, Mahdi2006

Hello, I have Debian 8 with XFCE Desktop installed on my Orange Pi 2. I downloaded the OS image from the orangepi.org a while ago and everything works OK except the WiFi. Does Armbian support the onboard WiFi of the OP2 ? If yes then I will change the OS today Thank you

Hi all. I've got an issue trying to use Bluetooth and RFCOMM. My system is: Cubieboard2 running latest img and updated with apt-get update/upgrade: ____ _ _ _ _ ____ / ___| _| |__ (_) ___| |__ ___ __ _ _ __ __| | |___ \ | | | | | | '_ \| |/ _ \ '_ \ / _ \ / _` | '__/ _` | __) | | |__| |_| | |_) | | __/ |_) | (_) | (_| | | | (_| | / __/ \____\__,_|_.__/|_|\___|_.__/ \___/ \__,_|_| \__,_| |_____| Welcome to ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 4.9.12-sunxi System load: 0.07 Up time: 30 min Me…

Hi Armbians, I'm running two identical Cubietrucks with Armbian Jessie systems in headless (very lean) mode without any X-Windows or the like. Both boot from 16GB SD-Cards. Now one of them, which had encountered a number of power failures, suddenly ran out of space on the SD-Card (100% usage of / ), while the other CT only shows 22%. I ran across this phenomenon, when the system failed to carry out an apt-get update at one point and important services Samba were no longer started. I then searched the root filesystem for culprits but there was nothing suspicious ... So I thought there might be a partial "destruction" of the fil…

New installed image: Armbian_5.14_Nanopim1_Ubuntu_xenial_3.4.112.raw [ 1321.621490] [cpu_freq] ERR:set cpu frequency to 240MHz failed! [ 1321.856382] [ARISC ERROR] :message process error [ 1321.874795] [ARISC ERROR] :message addr : f004b840 [ 1321.893322] [ARISC ERROR] :message state : 5 [ 1321.911038] [ARISC ERROR] :message attr : 2 [ 1321.928962] [ARISC ERROR] :message type : 30 [ 1321.946430] [ARISC ERROR] :message result : ff [ 1321.963905] [ARISC WARING] :callback not install

Hello, I try use UART interface on Lime2, but have problems with data transmission. Input echo 12345 > /dev/ttyS2 Output â–’;375 UART settings stty -F /dev/ttyS2 9600 -parity cs8 -cstopb How to detect the problem? Thanks

I would like to make Orangepi zero to capture USB output destined for a printer in order to log the output from a system. 1 ) Mimic the connected USB printer (so that the machine thinks it still has the original printer attached) 2 ) Capture the output from the machine 3 ) Send the captured output to the printer.

Hello, I am facing an issue regarding audio playback using the vanilla kernel( v4.5.2 ) for Banana Pi. There is no sound via the analog audio jack. aplay -l does show my playback device though. Here are some screenshots of my current config: speaker-test is throwing error: Should I need to configure anything else?

Since there isn't an Orange Pi Three forum I am going to post it here. Due to python requirements for PiKVM I installed the latest Jammy build. When i did the install everything looked like it worked but I could not get the remote keyboard and mouse to work with the OTG port. I tried changing the dtb but it didn't work. Comments in the kvmd-armbian discord channel recommended trying a different kernel. After trial and error I found OTG worked with kernel 6.10.9-edge-sunxi64 and remote keyboard and mouse functioned. With the default 6.6 kernel the ethernet port didn't work, but wireless worked. I was also able to get my mt7921u USB wireless adapter to work. In 6.10.9 the …

I was sort of disappointed with my RPi 2 VPN performance, which is about 2.5MiB/s while normal traffic can easily exceeds 5.5MiB/s. So I setup same VPN config on OPi One and run the test. The speed is impressive which is well above 5 MiB/s but it could only last about 10s before the box reboots itself. I can see one cpu core is occupied 100% by softirqd ( about 80% on RPi 2). My kernel version is 3.4.112 and StrongSwan version is 5.3.3. Don't have further information yet. When I get a chance to hook up serial console, I may collect more info.

Hi guys! I'd like to download the correct image for my Banana Pi M1, but I don't seem to be able to find it. I've been searching already for a bit without much luck. Is it supported? Am I missing something? Thanks!

Attention, whatever you do next is at your own risk! Fixed dts overlay file for Armbian 23.02.2 (attached). 1. Now the system can fall asleep and wake up by a timer (without an external RTC, provided that it is powered) or by pressing a button - while wifi connects itself (if there is an automatic connection) and the system continues to work as if nothing had happened without unnecessary loading. 2. As a bonus, I added an indication of reading from a flash card as a red LED (this can be turned off). 3. I also activated the host on the micro-usb connector - now you can connect something else via the otg adapter as a third USB connector. To apply t…

Hi everyone, I'm using the Orange Pi Zero 3 and would really appreciate a lightweight desktop image with just the XFCE desktop, a web browser, and basic tools (like file manager, terminal, etc.) with video acceleration. The current Armbian desktop image works, but it includes a lot of software I don’t need. I’m looking for something more minimal — just enough for light use and a faster experience. Does anyone have (or know how to build) a stripped-down XFCE image for this board? Thanks in advance!

I cannot get the screen to rotate 90 or 270 degrees. Inverting it works like it should, but not "sideways". uname -a: Linux orangepilite2 5.4.20-sunxi64 #20.02.1 SMP Mon Feb 17 02:37:37 CET 2020 aarch64 GNU/Linux xrandr --version: xrandr program version 1.5.0 xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192 HDMI-1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.00* 800x600 60.32 56.25 848x480 60.00 640x480 59.94 /etc/X11/xorg.conf.d/01-armbian-defaults.conf: Section "Monitor" Identifier "Monitor0" Option "DPMS" "false" Option "Rotate" "right" EndSection Section "Server…

Hi! I just installed Armbian Jessie on my Cubietruck to replace the outdated CubianX-distro. Title: Armbian 4.81 Cubietruck Debian jessie dev (unofficial) Kernel: Linux 2016.01-rc3 Build date: 28.12.2015 I use the Cubietruck as an owncloud-server and as a tvheadend-server. Tvheadend doesn't work properly. There seems to be a hardware-issue with the DVB-S2-receivers. One of them fails sometimes. Tvheadend often stopped. But now i found one (the?) reason in the syslog: lowmemorykiller Feb 4 08:29:04 localhost kernel: [11909.498000] lowmemorykiller: Killing 'tvheadend' (622), adj 0, Feb 4 08:29:04 localhost ke…

When connecting via a round connector, there is no power to SATA and USB, when connecting power to the USB-OTG, without disconnecting the round connector, power appears, when the power is turned off from the USB-OTG, the power on the ports does not disappear, while rebooting too. I tried to google, but to no avail Thank you in advance

Hi all. I understand, maybe my board Nanopi Neo CORE is not supported on the forum, but maybe someone will tell me how to write dts correctly # uname -a Linux NanoPi-NEO-Core 4.14.111 #126 SMP Mon Feb 22 17:04:18 CST 2021 armv7l armv7l armv7l GNU/Linux I compiled and installed ffmpeg with Cedrus H264 and cedar_ve.ko After that I see # dmesg | grep cedar [ 4.982170] cedar_ve: loading out-of-tree module taints kernel. [ 4.988972] sunxi cedar version 0.1 I'm trying to edit and compile /boot/sun8i-h3-nanopi-neo-core.dts using sun8i-h3-nanopi-neo-air.dts First I change before soc reserved-memory { …

Hi All, Armbian boots fine from SDcard but when I run nand-sata-install the script complains that it has no target. A #ls /dev/mmcblk* shows /dev/mmcblk0 and /dev/mmcblk0P1 When mounted, just to see, the mmcblk0P1 partition contains the usual linux directories, so I suppose this partition is definitely the SDcard No EMMC device is present. Could this be due to me performing, yesterday a: dd if=/mnt/ArchLinux_Minimal.img of=/dev/mmcblk1 bs=4M ? I did this because I read somewhere that booting up from SDCARD followed by a dd worked in some cases. Note I originally wanted to run Arch, but since there is apparently no support at orangepi.org, after…

I just updated my armbian kernel, I did it with: apt-cache search linux-generic to find the images and sudo apt-get install name of the image to install, the new kernel is in the /boot folder but if I restart It continues to start with the old one, and if I eliminate the old one it no longer starts. How do I select the new kernel to boot from it? i use orangepi+2e

Dear Igor, I want to compile a kernel for banana pro, there is an error. Show you how to fix it? Preferably with the new kernel. PS Sorry for my English

After along time I downloaded a new armbian image, after doing apt update/upgrade for the last year or so. I was quite surprised to see that the pcduino3nano is now deprecated, while other A20 boards are still supported. What was the exact reason that the pcduino3nano was dropped from support? If I keep using the deprecated OS, can I fully use apt update/upgrade for all user stuff? What would happen to all kernel and u-boot update packages? Is the latest armbian for the pcduino3nano automatically disabling those updates, or do I need to do something manually? *should* I block kernel & u-boot updates? thanks, Michale Jasson

I'm working with a Orange Pi zero and a new user to Armbian. I'm working with a Orange Pi Zero LTS(H2). From u-boot: CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero The serial console is working. I'm able to see the kernel and init output, and interact with u-boot. I've tried two Armbian versions and on both the kernel boots but there is no TTY on the serial port, I'm not able to interact with the OS. I see getty is launched, but there is no TTY. Here is the console tail of Armbian_community_24.8.0-trunk.104_Orangepizero_bookworm_current_6.6.31_minimal.img: [ 14.371884] random: crng init done [ 14.448177] syste…

I have problem with transmission-deamon on my CubieA20. It not starting listening on boot. Only after service restart. Met same problem on Raspberry-3 but it cured by enabling "boot to wait until a network connection is established" option. I checked the raspi-config and taken same measures on my A20 ("ExecStart=/sbin/dhcpcd -q -w" etc). Not succeeded! Anyone have alternate methods? There's some more applications that not starting on boot if connection not active, Blynk-client for ex. PS: I use legacy kernel on 5.25 Armbian. UPD: Problem resolved by editing /etc/network/interfaces.

Hi, I wrote Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113.img to sd-card and booted my cubietruck from the card. ssh in and user creation followed by reboot (rootfs resize) After that i performed apt get update&upgrade and started nand-sata-install. I have SSD hooked to CubieTruck and my goal is boot system from onboard memory (with 3.4-kernel nand is available but not with 4.9...) and roots to /dev/sda1. This was how previous setup was. sd-card slot is broken, I need to use tape to keep card on the reader, another reason why boot from nand would be nice. However, when i start and-sata-install, following is displayed on con…

I'm running "Armbian_5.34.171121_Orangepizeroplus2-h5_Ubuntu_xenial_next_4.13.14.img" on an OrangePi Zero 2+ H5. Lots of testing was done with the OS installed on and running from the SDCard. I've solved the board's overheating problems by installing a 30 x 30 x 7 mm Heatsink, plus a 50mm USB Powered Centrifugal Blower Fan. At long last the board runs happily at temperatures typically up to about 40 degrees C at light to medium CPU loads, and at around 65 degrees C when the CPU is pushed to 100% utilisation. With this cooling solution, the board has been reliably running PiHole for about two months now. The 50mm fan and the big heat sink are not a very …

I run Armbian 20.02.1 stable on a zeropi which is used as a wireguard server and spotify direct client (USB to external DAC). Things run very well. Many thanks to everyone involved in keeping Armbian such a great distro! I noticed that when I turn on the ondemand governor the system becomes very unresponsive and music playback is stuttering. When I use the performance governor (even with min and max frequency both set to 480MHz) things run just fine. Most of the time 480MHz will be sufficient, but it would be nice to be able to take advantage of the ondemand governor. Any help is greatly appreciated.

Hi all, I am trying get wifi working on Nanopi neo air with the Mainline kernel v4.12.12. I enabled brcmfmac driver in the kernel. Downloaded the corresponding firmware(brcmfmac43430-sdio.bin) for AP6212 from : https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/plain/brcm. I have applied patch to the device tree to enable wifi (https://www.spinics.net/lists/arm-kernel/msg563666.html) I couldn't get the firmware loaded properly. Here's the log. [ 85.922929] brcmfmac: brcmf_attach Enter [ 85.922967] brcmfmac: brcmf_proto_attach Enter [ 85.922990] brcmfmac: brcmf_fweh_register event handler registered for PSM_WA…

Hi all I have a banana pi running armbian. After the update to kernel 4.8.4 I am experiencing problems in enumerating USB device during boot (meaning device connected before powerup) I get errors like: [ 6.572517] usb 4-1: not running at top speed; connect to a high speed hub [ 6.578537] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.578547] usb 4-1: can't read configurations, error -61 [ 6.789488] usb 4-1: new full-speed USB device number 4 using ohci-platform [ 6.848598] usb 4-1: not running at top speed; connect to a high speed hub [ 6.853598] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.853620] usb 4-1:…

hi, I am th owner of a lamobo r1 card. Last days i'have tried more than 10 debian/bananian/ubuntu/raspian/openwrt image. Most of them work fine. Community image are often better than sinovoip one ... Unfortunatly, my sata HDD never work. I'm using a seagate 1TB SSHD. I currently using the armbian ubuntu image. At boot, the hdd spin up and stop, and ubuntu don't boot. If I remove the HDD everthing work fine. Anybody have a working hdd using the micro usb power port ? I use an ipad charger and a good one meter usb cable. Any help is greatly appreciated. If I should provide more details, please let me know Thanks agemio

Hi everyone i got my ILI9341 TFT 2.4" display to work on armbian but the screen is cut off? i have no idea on how to fix this Orange Pi One

I did the following upgrades this morning libcurl3:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libgd3:armhf (2.2.4-2+deb9u3, 2.2.4-2+deb9u4), armbian-config:armhf (5.72, 5.74), linux-headers-next-sunxi:armhf (5.70, 5.73), linux-image-next-sunxi:armhf (5.70, 5.73), curl:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libcurl3-gnutls:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), linux-dtb-next-sunxi:armhf (5.70, 5.73), base-files:armhf (9.9+deb9u6, 9.9+deb9u7) and found my I2C bus not working anymore. I did a scan on the 4 buses (Olinuxino Micro A20) and found a device on i2c-1 instead of i2c-0, changed my settings and all worked again, so I guess one of the updates must…

Seems that USB is missing in the latest trunk pull Spoiler [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.0-sun50iw2 (root@YPC) (gcc version 7.1.1 20170707 (Linaro GCC 7.1-2017.08)) #2 SMP Mon Sep 11 23:11:59 EDT 2017 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Machine model: OrangePi Zero Plus2 [ 0.000000] Reserved memory: created CMA memory pool at 0x000000005c000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000…

Sir, I put ubuntu trusty image on Sd card in A20-micro-4gb board. I connected serial cable to uart0 connector which has 4 pins tx,rx,gnd,3.3v. But the log shown is strange. Minicom settings are 115200, 8N1. Please confirm that debug interface is on uart0 or any other pins.

Board OPi Zero 512, NEXT kernel 4.13.7, last Sunday compiled. I'm trying do start more than one Dallas 1 wire interface. My primary idea was to add second w1-gpio overlay but no success. The next one is to edit device tree for w1-gpio to add another pin, and then to edit fixup script. And need some help to understand this ( copied from sun8i-h3-w1-gpio.dts ) fragment@0 { target = <&pio>; __overlay__ { w1_pins: w1_pins { pins = "PD14"; function = "gpio_in"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { onewire@0 { compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&w1_pins>; gpios …

Hello Igor, I have a question, does the image has a built in NFS kernel module? I would like to use my CB2 board as an NFS server. Thanks PS.: on the site a small list about compiled kernel modules would be usefull