Allwinner sunxi

I just updated two Orange Pi One boards and rebooted them to get to the new kernel only to have them boot loop. I know, development, not supported. I'm not asking for a solution, I'm just alerting people to the situation so they can avoid messing up their boxes. Console log attached if you're curious. orangepione.txt

https://www.walmart.com/ip/GE-HDMI-to-VGA-Adapter-33588/52162868 https://www.armbian.com/orange-pi-one/ Can I connect a vga display to the orange pi one if I utilize a hdmi to vga adapter? The hdmi to vga adapter takes electricity from the hdmi connector. Xenial installed on the orange pi one. Thank you.

I'm trying to use armbian on orange pi one, and it does not start. Previously I used the armbian, however I needed to format the card, now I am putting the same version of armbian 5.25 server and desktop does not work, I tried version 5.35 and tbm does not start, the non-image card does not light any led. However, when using both debian xfce and ubuntu xfce for orange pi one of orangepi.org, the board called displayed video and is working.

I connected the dongle wifi but it does not seem to work. I get the error: rtlwifi firmware rtlwifi/rtl8192cufw.bin not available I have try to build, make scipts, git rtl8192cu-fixes, etc, but return error scipts/Makefile.build:432 recipe for target '/home/vbextreme/rtl8192cu-fixes/8192cu.o' failed my version armbian 5.24 kernel 3.4.113 you can pass me the prebuild module?

I have tested the orange pi one xenial. When I say test it is not benchmark tests. I do not know what the numbers say anyway. I open several common programs and watch what htop says. If I run an mp4 file on a media player, libre office and file manager it runs well and htop says about 300mb. It is a 10usd computer and I do not expect it to equal a x86 desktop. If I open firefox, firefox crashes before starting. Because of not enough ram? If I open chromium or midori ram usage goes to 100%. Cpu does not. You cannot really browse sites very well. Youtube videos is the same. Is it becuase 512mb ram is not enough? On my gnulinux x86 n…

This may be one of those questions that should be considered dumb, but I'll risk your flames and ask regardless. Is the Orange Pi ONE GPIO Pin layout the same as the Raspberry Pi? I haven't found much specific to GPIO on the Orange Pi One, but I did see someone who said they were flipped 180 from the RPI. Before I attach a project and risk frying project and./or board, could you point me to a reference that specifies the layout of the GPIO pins on the Orange Pi ONE? And, like I said, I'm really sorry if this is the dumbest thing you've had to read all day. I have searched, but could not find much specific to the ONE.

Hello ! I'm a proud owner of a Opi One which is supposed to be my media server and torrent server. I downloaded and installed Armbian, set it up, everything works great, but the only problem is video playing. I tried to run multiple videos and multiple formats (.mkv, .mp4) but the player remains black. If I go on youtube, the video plays but it's very laggy (like 10fps). What should I do ? Thank you ! Guess here is my answer, too: http://forum.armbian.com/index.php/topic/1129-h265/

orange pi one h3 512mo ram didn't boot up and it stop at starting kernel this happend for both armbian version in the armbian website , i tryed also a version from the official website of orange pi one and it pass this step but show black screen .is there any image work properlly on orange pi one H3 please hekp

Hi. I'm working on it.I tried different systems ubuntu_lxde_desktop vs... Armbian 5.35 3.4.113 desktop board. gives a pink image error like in the photo. h3disp -m 1080p60 -d I've tried h3disp -m 1080p60 -c 1 I've tried h3disp -m 1080p60 -c 2 I've tried h3disp -m 1080p60 -c 3 I've tried but still no image how can i fix it ????

orange pi one desktop apt-get update apt-get upgrade https://docs.armbian.com/User-Guide_Getting-Started/ I cannot update and upgrade. I get these messages $ apt-get update Reading package lists... Done W: chmod 0700 of directory /var/lib/apt/lists/partial failed - SetupAPTPartialDirectory (1: Operation not permitted) E: Could not open lock file /var/lib/apt/lists/lock - open (13: Permission denied) E: Unable to lock directory /var/lib/apt/lists/ W: Problem unlinking the file /var/cache/apt/pkgcache.bin - RemoveCaches (13: Permission denied) W: Problem unlinking the file /var/cache/apt/srcpkgcache.bin - RemoveCaches (13…

Hello, I am trying to get my Orange Pi One working with my ili9488 LCD screen. I followed a few "how-to's" , This one in particular There is a comment there that mentions how to do it on the Orange Pi. Also this post here. I must be missing something, because when I did all the actions listed in every "How To" I found; all I get is a black screen with a white bar down the side. Does anyone know of a comprehensive how-to on getting this screen to work?

Hi! I'm new to Armbian and I have a problem with Internal Ethernet device on my Orange Pi One. Ethernet link successfully up on boot, but after 2-3 hours it goes down and only restarting it with /et/init.d/networking restart helps for the next 2-3 hours. But after 2-3 hours it goes down again and did not up untill I'll do restart networking manually again. I use the lastest Armbian_5.14_Orangepione_Debian_jessie_3.4.112. This is a log messages, which I found when network fails: Jul 27 16:00:01 localhost rsyslogd-2007: action 'action 17' suspended, next retry is Wed Jul 27 16:01:31 2016 [try http://www.rsyslog.com/e/2007 ] Jul 27 16:00:05 localhost kernel: [ 6087.…

https://www.armbian.com/orange-pi-one/ Is the armbian stretch system a free software system as defined by the free software foundation? Thanks.

Hi everyone, I am using an orange pi one to run a table top CNC machine I built and using it to run bCNC to send the g-code to an Arduino. I had downloaded and flashed an image of the Debian Jessie Desktop V5.20 a while ago and it has been working great for other things along the way as well as this project. I had some issues with the bCNC program and decided to uninstall the OS and restart from new. When I did, everything seems normal until I get to the login screen in the terminal area where I have to create a new user account and password and enter my information, then it asks if I want to change the display settings from what I already have which I don't…

Orange Pi One is not booting with Debian Jessie Server image http://www.armbian.com/orange-pi-one/ http://mirror.igorpecovnik.com/Armbian_5.14_Orangepione_Debian_jessie_3.4.112.7z But there is no problem booting with the Debian Jessie image made by Boris Lovosevic https://drive.google.com/open?id=0B1hyW7T0dqn6c3BNOWRwRnZZUTQ One month ago I got to boot another Orange Pi One with the image available at armbian.com/orange-pi-one/ but not any more This is the way I dd to SD card sudo dd if=Armbian_5.14_Orangepione_Debian_jessie_3.4.112.raw of=/dev/rdisk2 bs=1m I would really appreciate your help I am the maker of this demo and Instructable Swift …

Hi, I have a orange pi one and the jessie-lite from this site. Everything runs fine when freshly installed, however after apt-get upgrade and init 6 it stops working. I get nothing displayed on my hdmi any longer etc. Any ideas?

I've been away from armbian for a few months and came back to build a new project with my orange pi one but the nightly/recent mainlines builds seem to have stopped. I need a mainline kernel, and can grab one that's a few months old, but I wanted to be sure they haven't been moved. I'm not complaining! Just asking. With the number of boards available with armbian there has to be a lot of overhead doing nightly builds with few users, so it's not too surprising to see a change. I looked thru the sticky notes, but could not find a relevant post. Thanks!

Does somebody know if there are any size limitations connecting external USB HDD to Orange Pi One ? I'm thinking to buy a 3TB Seagate Desktop Expansion drive (it's self powered) to set-up my OPi as torrent box (now it's working with 1TB drive, aslo from Seagate). Thank you !

Hello, I'm new to the Pi computers and all that, and I'm planning on doing a project, so I was wondering if the Opi One H3 would support packet injection and monitor mode on Armbian with the onboard wifi? Thanks in advance.

orange pi one xenial stretch armbian-config desktop On xenial playing mp4 and mp3 files on mpv media player does not stutter. Also not on vlc. On stretch mp4 and mp3 files stutter on mpv media player and vlc player. Is that a general error? Thank you.

Hi, I'm trying to make my opi one act as a keyboard. I've found that I need to activate g_hid module, but when I trying to execute: modprobe g_hid it says: modprobe: FATAL: Module g_hid not found. Also, g_ether, g_mass_storage, g_multi, g_ptinter and g_serial modules are available. So, what should I do and maybe anyone can provide me an example how to send a keystroke to my pc? Thanks.

Hello, Is any way to use the full cpu potential from the board. I have tried the environment settings from one of the threads where gpio-regulator-1.3v is introduced but without success. Thank you Sent from my D6503 using Tapatalk

I have a board of Orange Pi One Plus with installed pihole (https://pi-hole.net/). Armbian image is Armbian Buster with latest updates. PRETTY_NAME="Debian GNU/Linux 10 (buster)" Each 2-4 hours the device hangs and not able to respond to any command until I reboot it. The max uptime that I was able to gain was ~25 hours. I've changed power adapters, powered it via microUSB - same result. Looking at the logs I really have no clue why it stucks. Attaching debug, kern and syslog. Probably someone may pinpoint what's going on. P.S. Previous OPi One (not Plus) worked for that purpose like a charm. Didn't know that bying Opi One+ for upgrade will buy me loos…

I have several OpiOne Plus boards. They differ by the date of manufacture (let's say 1st batch and 2nd batch) 1st batch: Works with kernel 5.10.x but does not boot kernel 5.15.x. Red light is on, power meter shows very little consumption, ethernet does not go up. Switching to last available 5.10.x kernel resolves the situation. 2nd batch: Successfully work with both 5.10.x and work with 5.15.x. Green light is on, power meter shows adequate consumption, board works. I'm pretty sure, that no more "new" opi one plus will appear at Xunlong shop and this issue won't be fixed in visible future. But well.. How I can "freeze" kern…

Greetings! It's not a influential or serious bug. I couldn't control the LEDs on Orange Pi One Plus by the command setleds, So I navigated to /sys/class/leds, and there are two items: orangepi:green:status@ and orangepi:red:power@. I tried to do echo 255 > brightness respectively and found that: orangepi:green:status@ controls the RED LED, while orangepi:red:power@ controls the GREEN LED. Please tell me if it's a minor bug or an intentional setting, thank you.

Hello everyone! can anyone help with latest debian/ubntu on Opi1+ and emmc storage. There is no /dev/mmcblk1p* . Only /dev/mmcblk0p* (microSD). Aslo there is no option in armbian-config...

Is it possible to install a desktop Enviroment on the Orange Pi One Plus without any problems? Whenever I use the Armbian config minimal desktop option, the Orange Pi stays on a red LED. It says it cannot install simpleFB, and it just sits at the starting kernel screen.

After flashing the last release (21.02.3) of Buster for Orange Pi One Plus H6 I discovered that no sound card was available. aplay - l gave: Then flashing a one year old version (20.02.1) the hdmi audio was available. But after making the updates, apt-get update , apt-get upgrade and enabling the Desktop aplay -l gives : no soundcard found. Please Help Regards https://www.fiatb.fr

Hello, I’m from Russia, I don’t speak English well, I write a translator through Google, I hope you will understand me. My Orange Pi One Plus H6 installed different Armbian image 5.3.9 the system works well, but there is no sound via HDMI, in the pulseaudio tab of the configuration menu it says "there are no cards available for configuration". Did I understand correctly that the H6 processor does not support the audio codec, so there is no sound, or am I doing something wrong? Thanks for the answer.

Hello. I would like to download the iso of the Orange pi One Plus with Kernel 4.19. But when i click on the link the image that i download is whit Kernel 4.18. Can you help me?. Regards.

I'm trying to get the Orange Pi One Plus' OTG port to function in "otg" or "peripheral" mode. I've modified the device tree configuration to change the "dr_mode" from "host" to "peripheral". This works as long as the Orange Pi One Plus and the device are separated by a hub. If directly connected via an OTG cable/adapter the device instead charges from the Orange Pi One Plus. I assume this would be due to the OTG port acting as a power source rather than a power sink. However, after experimenting I've been unable to find a device tree configuration change the role of the vbus. Does anybody have any advice?

Hi I own since a while an Orange Pi One Plus board that I have been unable to use till now (OS images supplied by manufacturer are just a joke !). I wanted to give it a test with ARMBian as you offer now some Beta images. As both Bionic and Stretcher are offered, is there one of them more stable or more near something finished ? Did someone have tried the board with one of these ? and did it work ? Thanks Vincèn

Hey there, I just build a fresh dev image for the OrangePi One Plus (Stretch, console only, 5.0.x megous sources, latest commit was https://github.com/armbian/build/commit/783c2d0e25ff4542876943cfef6a7ac2921d1262) and unfortunately it seems to be unbootable. I put verbosity to 7 to get some more information rather than being stuck at "Starting kernel..." and this is what came up: Spoiler U-Boot SPL 2019.01-armbian (May 02 2019 - 13:14:43 +0200) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.1(debug):9a25f98-dirty NOTICE: BL31: Built : 13:14:40, May 2 2019 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: B…

Please help, what I am missing? With legacy kernel installed acpid and pressing power button on OpiOne gives me events (monitoring with acpi_listen). Same thing not working with next kernel 4.14.18. Do anybody have solution?

orange pi one armbian xenial When I obtained the orange pi one I installed armbian xenial. I booted the orange pi one. During boot I cannot recall if a red light flashed next to a steady green flash. The desktop worked. The orange pi one was connected to a hdmi display. Resolution 1280 x 720. I wanted to use a 1024 x 768 vga display by hdmi vga converter. The desktop would keep the 1280 x 720 resolution when displaying the desktop. I tried different things in order to get a 1024 x768 resolution. Did not work. One configuration resulted in trashing the power supply. I connected another power supply. The power suppl…

Hút bể phốt số 1 hn – địa chỉ nào tốt nhất Tại Hà Nội hiện nay, tình trạng tắc nghẽn, đầy bể phốt thường xuyên diễn ra gây ảnh hưởng nghiêm trọng đến cuộc sống sinh hoạt của người dân. Một trong những giải pháp tốt nhất trong những trường hợp này đó chính là sử dụng dịch vụ hút bể phốt của đơn vị hút bể phốt số 1 hn - Công ty hút bể phốt Avico với chất lượng dịch vụ hoàn hảo nhất. >>> Mời các bạn xem thêm về Dịch vụ hút bể phốt tại quận Hoàn Kiếm Avico : https://hutbephottaihanoi.vn/hut-be-phot-tai-hoan-kiem/ Những lý do khẳng định Avico là đơn vị hút bể phốt số 1 hn Trên thị trường hiện nay có vô vàn đơn vị cung cấp đến với người dùng trên thị trư…

Hi , my op one board is installed latest armbian but i couldnt see serail ports The default serial port /dev/ttyS0, used for (bootstrap) debugging and the serial console, is located at J11 - refer to the picture and instructions below. The Raspberry's "original" serial port on GPIO 14 and 15 (CON3, pins 8 and 10) can usually be accessed as /dev/ttyS2 on the Orange Pi Plus. J12 also provides another serial port on pins 4 (RX) and 6 (TX), which should map to /dev/ttyS3. only i see /dev/ttyS0 and /dev/ttyGS0--GS4 how can i fix this issue ?

orange pi one First the orange pi one was connected to a 1280 x 720 hdmi display. Then I connected by hdmi to vga converter the orange pi one to a 1024 x 768 vga display. Orange pi one keeps the 1280 x 720 resolution. And another resolution cannot be set in menu display. How can I set resolution to 1024 x 768? Thank you.

I came across a spi clk problem with my Orange Pi One. A similar unanswered question has previously been asked for Orange Pi Zero, but I started a new topic because of the new board. I am using ARMBIAN 5.32.170913 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i Everything is set up properly and spidev0.0 is created and working. Following is my /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 fdtfile=sun8i-h3-orangepi-one.dtb overlay_prefix=sun8i-h3 rootdev=UUID=a2df1e68-90c9-46a0-ab26-169cb43e35c8 rootfstype=ext4 overlays=spi-spidev i2c0 uart1 uart2 uart3 param_spidev_spi_bus=0 param_spidev_spi_cs=0 verbo…

orange pi one synaptic package manager I installed the synaptic package manager on Armbian Xenial. If I input something to search for one core goes 100%. The search is so slow I have not let it finish it. Is it a bug? My raspberry pi 0 is able to do a search fast. Thank you.

Hi, i try to use my orange pi one armbian to do uart debug on orange pi 2g iot I use uart3 on orange pi one and my configuration [uart0] uart_used = 0 uart_port = 0 uart_type = 2 uart_tx = port:PA04<2><1><default><default> uart_rx = port:PA05<2><1><default><default> [uart1] uart_used = 0 uart_port = 1 uart_type = 4 uart_tx = port:PG06<2><1><default><default> uart_rx = port:PG07<2><1><default><default> uart_rts = port:PG08<2><1><default><default> uart_cts = port:PG09<2><1><default><default> [ua…

There are two USB dongles on my Orange Pi One box, one is a USB Bluetooth in USB-OTG port and other is a mu7601 USB WiFi in the USB port. When I switched it from legacy kernel to lastest development kernel 4.11.x, the bluetooth card disappeared. So I exchange two dongles each other , the one in USB port works, and the one in USB-OTG port always failed. Is there any solution?

I'm trying to get an nrf24l01 radio to work on my Orange Pi One but have not been successful. I'll document what I've done here. If you spot an error, please let me know. Start with fresh Armbian_5.20_Orangepione_Debian_jessie_3.4.112 image. Then apt-date update and apt-get upgrade. Attached nrf24l01 like this (pictures of header and radio are attached for verification); nrf24l01 color opo pin opo fn 1 GND blk 25 ground 2 VCC red 17 3v3 3 CE org 29 PA7 4 CSN ylw 24 CS0 (SPI-CE0) 5 SCK grn 23 SCLK 6 MOSI blu 19 MOSI 7 MISO mag 21 MISO 8 IRQ n/c git …

Hi, my environment is: Orange Pi One ARMBIAN 5.34.171031 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i WiringPi fork by WereCatf: git clone https://github.com/WereCatf/WiringOP.git -b h3 ./build small c++ programm: #include <stdio.h> #include <string.h> #include <errno.h> #include <stdlib.h> #include <wiringPi.h> #include <pthread.h> static volatile int globalCounter; void myInterrupt(void) { ++globalCounter; printf("InterruptCounter: %5d\n", globalCounter); //digitalRead(7); } int main(void) { if (wiringPiSetup() == -1) { print…

Hi all, First of all sorry if i posted in the wrong directory I'm currently facing some issues with my orange pi one and in particular with node red and my dht22 temperature and humidity sensor i installed the stable buster version on my sd card this works perfectly and after that i installed node-red on it. in node red I installed the dht sensor pallet and added it to my flow but here is were the issues are starting, i need to select which pin it is connected to and what gpio i use. i can only select bcm gpio, rev1, rev2 or wiringpi 1 or 2 and then which pin it is connected to. i have the sensor connected t…

I've posted this on the Orange Pi subreddit here: https://redd.it/5bqnghbut figured a more active community might be better. I am using my Orange Pi Ones for SETI@Home, I also use Raspberry Pis for the same purpose. I've noticed since, around, Armbian 5.20 that SETI@Home(BOINC) won't stay running for any more than 6-12 hours. It's being sniped by Out of Memory. I've tried a few things, posted on the subreddit, but here is the short list: Logged Memory ---> Can dip below 100MB during usage but not often Enabled Swap/Increase Swappiness---> 0 to 10 (I don't care about SD Card life) Adjusted BOINC/SETI to use 75% memory None of the above seems to have helped. The…

Ethernet was working fine for me, up until I rebooted the board. The LEDs on the ethernet port blink briefly during boot, but once booted they are off, and the board does not have an IP address. Via serial console I undid the change I made prior to the fateful reboot (adding 'overlays=uart1' to '/boot/armbianEnv.txt') and rebooted again, but to no avail. Having searched for the issue, I also confirmed that my power supply is sufficient; running 'stress -c 2 -m 2', and measuring across pins 2 (5V) and 6 (GND) of the 40-pin header, I get 5.05V. As I don't have a network connection, I did not run 'sudo armbianmonitor -u', but I gathered the following …

I am a newbie here and newbie in Orange Pi One. Previously I have used Raspberry Pi in my daily projects. I burn Armbian 5.05 to my class 10 SD Card and after install the SD Card to the board. My Orange Pi One is booting properly but after automatic restart, my board doesn't continue to boot but the red LED is ON. I have tried to wait for 10 minutes but nothing work. This is my first booting https://www.youtube.com/watch?v=_RA68P_WZJY .

[Apologies. There seem to be a number of posting close to this subject. Trying to get a definitive view] So, with the 3.4.113 kernel the gc2035 driver fails when trying to identify the sensor. The problem lies in the sensor_init function where a read of the I2C/CCI bus fails. Before I break out the breakout board can anyone verify these basics please? I've tried the various suggestions for setting one of the GPIO pins prior to loading the modules but to no avail. Cable, blue insulation on top side of the expansion board FPC, blue insulation facing up towards SD card on the OPI one. FEX as below. [csi0] vip_used = 1 vip…

Hello, I try to communicate on UART3 (pin 11/13) just TTL, but cannot see any data on the lines. After first attempt i added overlays=uart3 to /boot/armbianEnv.txt and rebooted the system. oot@orangepioneplus:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun50i-h6 rootdev=UUID=d7bd3629-b17f-4c85-9031-909157a0ce7e rootfstype=ext4 overlays=uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Then i also executed update-initramfs -u and rebooted the board. None of these are helped I wonder what i am doing wrong? I see the following in the logs: root…

I thought I had this mastered but I cannot get the OPI to boot. I downloaded the current legacy image trusty, use 7zip to unzip it and then use a image writer to write the image to the SD formatted sd card. Am I missing something here? Sent from my SAMSUNG-SM-G900A using Tapatalk

I've tried both revisions (Bionic and Stretch) for this board located at: https://www.armbian.com/orange-pi-pc/ Both have the same issue. When I boot from sd card, run armbian-config, and attempt to transfer armbian OS to emmc I get an error 'no target'. I know that there is indeed built 8GB flash, because when I pull the sdcard, and power the board it boots into the pre-configured android OS. Here is a picture I took of the board: https://photos.app.goo.gl/5ELPTTnPbZXAybhe9 Any advise would be helpful. Thank You.

Hello, I am opening new topic because I simply cannot get monitor running on 1280x800. I only get shrinked picture, that isn't that I am looking. I also cannot understand how to add new resolution to kernel. Please help, thanks all in advance

For days now I have been fighting to get this thing working. No boot, No hdmi, no sound, no wireless network and so on. Armbian is anyway the best choice for this device, Supported? well yes if you have lan, true HDMI Well i got it to boot, after writing a new image to sd card. finally booted, no signal detected ( with a DVI > HDMI ), I had to hook it up to a true HDMI and modify the script.bin file to get a signal. Got it to boot all the way to the desktop. Hurray ! Plugged in a crappy wifi adapter from Ali express (realtek 8081 i think it is) and I got wifi, jippi. Next time booting no wifi, no matter what I tried. Made a new image again, with modi…

Hello, I managed to run OPi as a media player using OpenELEC (works charmingly fast - much much better than on RasPi), bun on Armbian (legacy kernel - 3.4.113) something went not too good Firsty, I burn desktop Xenial image onto SD card, dropped into Orange, and everything worked fine besides sound via HDMI - even locally played MP3 files were stuttering, not mentioning Youtube in Chromium - CPU usage was in range of 30-40 percent. Sound in TV speakers were annoying- one second of music, long pause, repeated until I press stop button. So I gave up with Xenial, write a Jessie server image (also legacy kernel), installed XFCE with all recommende…

Hello, I installed the Ubuntu desktop image from: https://www.armbian.com/orange-pi-pc/ to the SD Card with: sudo dd bs=4M if=Armbian_5.38_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img of=/dev/sdb conv=fsync The orange pi does not boot, it took some time and the red LED is flashing on the top side and the screen is black. Maybe I did something wrong? Regards, caro

Hello, I've downloaded and installed armbian for Orange Pi PC (debian legacy), and it boots ok. When trying to shutdown using systemctl shutdown I get "kernel panic - not syncing - Attempted to kill init - reboot in 10s", and i'm unable to see more info. I have installed the OS in the past(3 months ago) without any kind of problem. I appreciate any help, Thanks

Edit: Nothing was wrong with the Orange PI. I turned out to be my switch. Hi All, Firstly, Armbian is just fantastic. Secondly, this issue is highly likely to have nothing to do with Armbian, but just the cheap crap you'd expect from a cheap SBC. Essentially, after much pain and anguish having bizarre Ethernet connectivity issues with a shiny new Orange PI PC I bought a couple of days, which was: 1. When OPI was connected my network switch (which has four other devices connected to it: two Ethernet and two WiFi), none of the other devices can reliably 'ping' or SSH to the OPI... 25% to 100% packet loss. 2. When connecting the OPI physically directly to ex…

I just tried my Orange Pi PC with a Samsung TV connected via the HDMI port. I'm able to log in to the desktop OK, but when screen updates happen (e.g. when I scroll around in the web browser) the display goes black momentarily, then comes back after a fraction of a second. This seems to be worse for some applications (e.g. the web browser) than others (e.g. terminal), and so far I haven't seen it while not running X. Also, playing videos (with mpv) does not cause it. I'm running this image with no customisations: http://image.armbian.com/Armbian_5.20_Orangepipc_Debian_jessie_3.4.112_desktop.7z Any ideas how to fix this?

Hi, Good people of Armbian-land! First of all, thank you all for the awesome work you've been putting into Armbian. I recently purchased an Orange Pi PC, for which I'd like to use the Ubuntu desktop image, since I need the HW acceleration features. I tried using Mainline briefly but after confirming that the performance is just not there without the Mali drivers (as suggested by the description, so no surprise there), it seems Legacy is my only viable option. Which would be fine, but the monitor I'd like to use with my setup doesn't work with legacy (it works fine in Mainline). Also a sidenote: I connected the monitor using an HDMI-VGA converter. I set th…

I've experienced some issue on my OPI PC running 4.14 kernel - it disconnects eth after some hours of running. It's very annoying for me because I'm running Home Assistant automations on it and it's located in remote location (not in my home), so I have to drive 50 km to reset/reconnect it manually First I thought OPI just froze somehow (kernel panic or so). But later I've set up heartbeat trigger on red led and it's blinking, so OPI just disconnects from eth. When I unplugged cable for a minute and plugged it in back, networking was restored and I could reach via ssh. I'd like to make some workaround for now and the simplest thing seems to be write a script and pu…

I've installed armbian 5.38 debian stretch 4.14.14 on my Orange Pi PC .. after changing notwork settings (by using "armbian-config") from DHCP to Static , then back to DHCP, eth0 is not able anymore to get IP address.. "newtorkclt" return: IDX LINK TYPE OPERATIONAL SETUP 1 lo loopback n/a unmanaged 2 eth0 ether n/a unmanaged every suggestion will be usefull..

First time working with usb_f_uac1. Running buster image. I have a configfs setup that hosts are able to enumerate but the attributes for capture (c_chmask, c_ssize, c_srate) and playback (p_chmask, p_ssize, p_srate) seem to be switched. i.e. c_chmask = 0x3f shows as a 6-channel capture endpoint on both Windows (ksstudio) and macOS (system information) hosts. Is there something I’m misunderstanding here? Is there something I’m not doing correctly?

Hello Everyone, At first I'm sorry for my English I started working with Ubuntu server version -> Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. For my purposes I needed to enable watchdog on my board. It took me a while, but I managed to do it. After setting up whole configuration, and then start stop tests everythink seems to work just fine (watchdog reboot my bord). To finish whole process I wanted to enable wdog to start at boot, but it didnt activate after reset. After some digging in Internet and investigation i figured out that in watchdog.service file one line is missed which was in all other services. So after a…

Hi Everyone. I expect I'm making a simple mistake here, but I'm pretty new to this and could use some help. I am trying to set a static ip address on an orange pi pc running armbian Jessie 5.36. I want a static ip to set up an nfs between multiple boards. I've done this before on debian desktops, but this time I'm getting errors. I have tried multiple ways (editing the /etc/network/interfaces, nmtui, nmcli) without success. For simplicity, here's a version of what I'm doing. I start with a clean install. The Opi connects to my router fine. I add and update all the packages I need, then use nmtui to change the name of the network connection from "Ethern…

Hello again. I am beating my head against the network configuration again and would dearly love some help. I have two orange pi pc boards with static ip's in the 192.168.1. range. They are only connected to each other. They can ping and ssh each other just fine. I am trying to set up nfs shares between them without success. In /etc/exports I have: /home/martin/folder 192.168.1.*(rw,sync,no_subtree_check,nohide) I have "ALL: 192.168.1." in my /etc/hosts.allow. In /etc/fstab I have: 192.168.1.XXX:/home/martin/folder/from_lev /home/lev/folder/to_martin nfs rw,sync,noauto,user,x-systemd.automount 0 0 And vis-versa on the other pi. The fold…

kindly help me to mount usb devices. I have wifi stick, usb sd. nothing detects on latest deb jessy.5.05

Hi all, During a first installation, wireless worked with both ralink or rtl8192cu usb dongle. Though connection was unstable (ralink) or sometimes even freezing the system (rtl812cu), I could at least see the surrounding ssids and most of the times connect. Following a problem which bricked the opipc (my kid unplugged the board while I was playing with kernel), I reinstalled from scratch. And pouf ! None of my dongles work. Leds won't turn on, no wlanx in ifconfig, no ssids in network manager tray icon... however (tested only with rtl8192cu dongle), lsusb and lsmod seem fine (i can see rtl892cu in lsmod). The only difference I can think off between first and …

Let me start to express my gratitude for the wealth of information and software which is available here. I'm a longtime user of a usb 2.0 soundcard along with a laptop with KXStudio and Guitarix. I've used this setup many times for gigging and home recording and it proved to be stable. One of the downsides is the "voluminous" laptop. I've my soundcard mounted in a small 19" flightcase with one rack still open. For some years I've been thinking of making rack mountable effectprocessor from a board to substitute the laptop. So, to start this journey I've ordered a OPi PC (along with a good quality micro SD card!), of course not a heavyweight board, but my first…

Hi I tried several image but cannot boot..it is compatible for orange pi PC ? my target is BTSync. thanks

Have anybody tried to setup Amazon Alexa on the OpiPC?

Hello everyone, we are Colombian developers and we are making a project with a Orange Pi PC. We tried to connect the Orange with a laptop via USB/OTG but in Serial port mode following this guide, but we exactly need connect the Orange with the laptop via USB/OTG in Mass Storage mode, who can help us to set this mode, we are trying but not with good results. Thanks, I hope that you can help us.

Hi all . i write down about armbian at the last part of http://orange-pi-2.blogspot.jp/2016/01/orange-pi-2g.html in English . anyway armbian support minidlna well , so i enjoy video by vlc ( =dlna client ) . https://www.youtube.com/watch?v=vpMs9TOdgu0&feature=youtu.be ---- regards , tuyosi

I'm connecting my Orange PI PC 3.5mm jack to this power amp: HiLetgo 5pcs PAM8403 2x 3W Mini Digital Power Amplifier Board AMP Class D 2.5-5V Input If I connect a 5v 2a power supply to the amp and a 3a 5v power supply to the Orange PI PC, it sounds great with no noise form the Orange PI and no distortion from the amp power supply. If I try to run the amp from the 5v pins on the Orange PI PC with the 3amp 5v supply, it will work, but there is a lot of noise from the main board and the amp does not get enough power to run properly. Should 3a be enough to run both these peripherals? I think the power amp will pull about 600ma, not sure what the Orange PI…

Please help me to install printer to my OPI PC i use Armbian_5.05_Orangepih3_Debian_jessie_3.4.110_desktop.zip OPI sees the printer in usb but because of my low level of knowledge i only use tools in x desktop (windows like) , so i couldnt find any on desktop The main aim is to setup printer and make it sharable in wireless network (wlan is ok) so please help me to setup my printer step by step i d really appreciate it if you help

hi guys I'm amateur Linux user. now i can connect to internet with WiFi but i don't know how connect to internet via LAN (Ethernet) my problem is Ethernet setup . please help me for make small network with 2 or 3 client With the ability to share internet and file. my boards : 1 orange pi PC plus( Intended for server ) , 2 orange pi Zero 512Mb ( Intended for client ), network Components : LinkIt Smart 7688 (WiFi to Ethernet Bridge ) D link 8 port switch I'm so sorry for bad English

Hi, I have an Oracle PI PC+ which will not boot without the hdmi connected. If you disconnect the hdmi once the board has booted it crashes or at least stops responding to ping/ssh over the ethernet. I've used pretty much all the builds I can find on armbian.com including the nightly builds with don't show a display at all but still fail without the hdmi. I've also tried booting from SD card and the emmc almong will messing with the /boot config files such as setting the console to serial and can't see anything interesting in the messages file. It shouldn't be a power issue as I'm using an Anker 2.4a PSU but I've tried other PSUs as well wit…

I tried to install default linux kernel (3.4.113) on Orange Pi PC + and It's keep on rebooting while displaying kernel panic on console. Below I have attached the log U-Boot 2017.11-armbian (Dec 18 2017 - 14:24:28 +0530) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC Plus DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 In: serial Out: serial Err: serial Net: phy interface0 eth0: ethernet@1c30000 starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scan…

Hi Everybody. Can anyone publish step by step guide of building working solution of orange pi PC + ov5640. I mean something like: 1. Buy this ov5640 camera 2. Buy this cable 3. Connect so ... 4. Download this OS image. 5. Change this and that in configuration files Thank you P.S. I spend 2 days reading forum but still don't understand how to get work my Orange Pi PC + ov5640

SULVED! Cant get the wifi operate as i want it. i am using the nmtui tool for configuration. The following logs are with Lan0 connected. ------------------------------------------------------------------------------------- Welcome to ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i System load: 0.43 Up time: 29 min Memory usage: 27 % of 1000Mb IP: 192.168.178.19,192.168.178.58 CPU temp: 16°C Usage of /: 12% of 28G Last login: Mon Apr 17 17:09:41 2017 from 192.168.178.49 root@myboard:~# route Kernel IP routing table Destination Gateway Genmask Flags Metri…

Hello dear friends, please help can not solve a problem, the entire forum has clambered! as I can not turn on your WiFi Orange Pi Pc + ....

First, thanks to everyone here who made this great os. I am trying to read a DS18B20 temperature sensor on my orange pi pc, but I can't get it to work. I hooked up ground and 3.3v to the sensor, the data line I placed it on gpio 20/ physical pin 37 as other posts suggest but it is not reading it. I edited /etc/modules-load.d/modules.conf and modified it to: 8189es gpio_sunxi w1-sunxi w1-gpio w1-therm #gc2035 it loads up in dmesg .... [ 6.030874] W1_SUNXI: Added w1-gpio on GPIO-20 [ 6.039203] Driver for 1-wire Dallas network protocol. .... but it is not visible in /sys/bus/w1/devices/ I tried other gpio sensors, currently I can read from an i2c sen…

Steps: - Installed "Focal xfce desktop" Orange Pi PC 2 image - Installed mesa-utils - Set display resolution 1920x1080 60hz - Run glxgears Actual behaviour: - running at 30fps Expected behaviour: - running at 60fps or higher Additional information: - glxgears -info output: https://pastebin.com/y4W30MFg

Hello so i got Orange Pi PC 2 today and installed armbian from here : https://www.armbian.com/orange-pi-pc2/ i can SSH to it. but i dont know how to get AV out to work :/ can u help me ? im a total Beginner i just need to get Tv out to work and start learning. I know that armbian for H5 is in the early development state.

Hi All. May be I miss something but I do some searching and still can't understand. Problem configuration: Orange Pi PC v 1.2 (try 3 different) fresh loaded Armbian_5.90_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img (try different SD cards) any (try 3 different HP 2824, Zyxel Kinect, Cisco SRW2016) If I plug my Orange Pi PC with this image to 1Gb port I'v got blinking of lights and dmesg: [ 818.090335] PHY: gmac0-0:00 - Link is Down [ 819.090497] PHY: gmac0-0:00 - Link is Up - 100/Full [ 821.090494] PHY: gmac0-0:00 - Link is Down [ 822.090314] PHY: gmac0-0:00 - Link is Up - 100/Full [ 824.090335] P…

I'm on an Orange PI PC running Armbian_23.08.0-trunk_Orangepipc_bullseye_edge_6.5.1_minimal I've enabled analog audio out the 3.5mm jack using overlays=analog-codec in /boot/armbianEnv.txt I'm connecting the analog 3.5mm jack to a 3watt amp & speakers. It works mostly, but I only get audio on the left channel. Alsa mixer Line Out only allows one channel to be unmuted at a time - left channel or right channel. Left channel sounds pretty good (DAC reversed appears to increase dynamic output). Right channel is very low volume and appears to be "squelched" - is the audio signal reversed from ground or something? Anyway, is there some …

Hi all, I trying many days set up temperature sensor work, but no luck ( Orange PI PC Armbian 20.11.3 Focal with Linux 5.9.14-sunxi try many pins, 3 and 5 V , but same result, no sensor read. No any resistor, 1 sensor armbianenv: overlays=w1-gpio usbhost0 param_w1_pin=PD14 param_w1_pin_int_pullup=1 output: root@orangepipc:~# gpio readall +------+-----+----------+------+---+OrangePiH3+---+------+----------+-----+------+ | GPIO | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | GPIO | +------+-----+----------+------+---+----++----+---+------+----------+-----+------+ | | | 3.3V | | | 1 …

Hi! I got a strange problem. When I run apt-get update OPiPC hangs and don't respond to anything. Last thing I see is: root@dbot:~# apt-get update Get:1 http://security.debian.orgjessie/updates InRelease [63.1 kB] Get:2 http://apt.armbian.comjessie InRelease [8,682 B] Get:3 http://apt.armbian.comjessie/main armhf Packages [95.8 kB] Get:4 http://httpredir.debian.orgjessie-updates InRelease [145 kB] Ign http://httpredir.debian.orgjessie InRelease Get:5 http://apt.armbian.comjessie/utils armhf Packages [3,702 B] Get:6 http://security.debian.orgjessie/updates/main armhf Packages [320 kB] Get:7 http://apt.armbian.comjessie/jessie-desktop armhf Packages [7,368 …

Hello, I bought Orange PI PC and tried ubuntu mate but ended up deleting it because wifi was not working.After search i found this Armbian OS and its always updated.I have downloaded armbian for my orange pi pc. Extracted the file and I then used win32 disk image for write image on sd card.After succesfull write what i find is that the memory card becomes inaccesible from my windows 10 pc.Do i have to copy any additonal file like kernel script bin or uImage?because in ubuntu mate from orangepi forum i used to copy to ubuntu mate. When i plug that writed sd card to orangepi and connected to hdmi screen it gets started and booting.AFter it reaches to login so…

Hi. I run armbian on a opi pc for a while. It works fine for a couple days when I work with this board. After that I left the board unpowered for two weeks or so and when I want to powered it on, it does not boot, I need to reconnect the power again to boot. This was the first time when I encountered a problem, the uptime was wrong, it is shows me 2 weeks, I reboot the board and it was ok after, it stays on and all worked fine for 10 hours until I shut it down. But I had this problem often, doest not want to boot from first time, board freeze after some time and I need to reboot to work properly. Uptime and date/time is correct but when I want to see the statu…

I'd like to use Orange Pi PC as a HID keyboard USB gadget/USB device. There is a tutorial on link here but it makes Orange Pi into a serial device. I want a HID device (keyboard).

Hi gang. I am having a consistent problem changing the board over boot from the SD with the system on any kind of USB attached drive. The drive I want to put it on is a 1t ssb, which otherwise formats fine, over and over again, burns images on it fine (though rpi doesn't like how much power it grabs). But I duplicated the problem with a formatted SD card in a reader in the USB port as well. The same error message appeared. Now I have to say that I have read this post here: to see if there was anything unique to the H3 to accomplish this, but Igor said there to just follow the simple directions at Getting Started, which though dated, still work close…

Hi, I’m curious how to boot into command line rather than the GUI desktop when booting up. I have looked at some other answers where changing the `nodm` but that file does not exist. Thanks!

Hi, I have used the official armbian focal image for orange pi PC (https://www.armbian.com/orange-pi-pc/) The issue is in the armbian-config navigate to system -> Hardware you see nothing as shown below Please find the monitor log http://ix.io/2WQv

I'm trying the Orange Pi PC for a smal project but while installing th OpiPC corrupts its SD Card. Typical error occurence: - Install Debian Jessy server on 16GB SD Card (ScanDisk Ultra class 10). - run first bootup. - update und upgrade software, install nfs-common and rrdtool. - setup keyboard, console-setup, tzdata, locales, static ip. - edit /etc/fstab, mount nfs-volume. - copy project software (mostly bash scripts, reading cpu temp and switching GPIO-Pin). - seting up a cron job. on one of the next shutdown/reboot the console shows mmc errors while reading and writing (see log file). - the Sd card can not be started any more, all attempts fail with mm…

I have an Orange Pi PC with the Allwinner H3 processor running the latest 5.20 version of Armbian. I am unable to successfully connect to a Wireless access point because as soon as the status of connection is "Obtaining IP address" the Orange Pi PC crashes and reboots. I have tried this with both a reputable Edimax wifi dongle and a cheapy wifi dongle with the same results. I can have them plugged in and the OPi and it will run fine but as soon as I try to connect to a wireless network, it crashes. I have the OPi PC connected to a variable power supply capable of 3A and it isn't getting anywhere near that. So my 5V isn't a problem. I have updated and upg…

Received a batch of OPi PCs and one is not booting. In serial console I get only: U-Boot SPL 2016.09 (Oct 15 2016 - 14:20:45) DRAM: 1024 MiB Trying to boot from MMC1 And that's all. What's wrong with it? SD card and PSU verified working with another OPi devices.

My orange PI PC was working flawlessy but now it wont boot and via serial I can get this: U-Boot SPL 2016.09-armbian (Oct 23 2016 - 17:08:22) DRAM: 0 MiB ### ERROR ### Please RESET the board ### Then it stops there. What can I do?

I have OrangePi PC and I'd like to use HC-12 serial communications device. I've successfully used it with RaspberryPi Zero with these instructions: http://dev.drun.net/2017/05/10/reading-hc-12-from-rpi-and-sending-to-domoticz/ I've found this useful info: https://forum.armbian.com/topic/1524-orange-pi-one-how-to-enable-uart/ I've connected the HC-12 to OPPC as follows: VIN – Connect to 3.3 (PIN 2) GND – Connect to GND (PIN 6) RX – Connect to (PIN 8, UART0_TXD) TX – Connect to (PIN 10, UART0_RXD) I've got Putty connected to OrangePi. command "ls /dev/tty*" shows that I have /dev/ttyS0. I've tried to use it with Minicom: sudo…

I am running a relatively new install (few months) on a replaced microSD (RMA). Keep in mind this is a headless install. At random, usually after many days / weeks+ the orangepi appears to freeze. What I mean with freeze: - samba shares disconnect - sometimes SSH works till the password is submitted, then it times out - sometimes http works when I hard restart it - I always see a very high temp & in some logs I had seen some weird dates, so I set to write out date & temp and I got this beauty on the next freeze: Spoiler date: Sun Sep 30 13:27:03 2018 -- temp: 41.99 date: Sun Sep 30 13:28:…