Allwinner sunxi

Hello, I have installed the latest version of armbian on my Orange pi win and I have not been able to make the desktop appear, it always stays waiting for a command, I have done update and upgrade and nothing. Can somebody help me

Hello, I have a fully working customized Armbian on OrangePi PC Plus. There are two partitions, one for the rootfs, second mounted as /home I want to convert the root partition to squashfs, and use the squashfs file to boot from. I already converted the root partition to squashfs file, I can mount squashfs file, and the contents are correct. I even tried to mount it via fstab and it works. I searched everywhere, obviosly not enough, but I cannot find a way to boot directly from the squashfs file. The idea is to have only squashfs file and rw partition for /home Please, can somebody help me, or point me to the right instructions ?

Hi there. First time posting. I already installed the latest version of the desktop version for my M1 and I was gratefully surprised how an old device is still working thanks to the armbian community. Thanks all of you. I am on a retro project trying to make my M1 working on an old crt TV through the pal/ntsc video output. New compiled kernel doesn’t seem to have the necessary driver/module. Any workarounds/ideas to achieve that? thanks

See build log https://paste.armbian.de/lesoquheja The kernel works, but installing the .deb failed because my extlinux script could not copy: /usr/lib/linux-image-6.18.1-edge-sunxi/overlay/sun8i-h3-analog-codec.dtbo The whole overlay folder does not exist. It does exist for 6.12.58-current-sunxi and last time I compiled kernel for the nanopineo was 6.16.8, the overlays were created. I remember it was also once the case with edge kernel for other SBC ( .deb package from the Armbian beta repo). That time own local build did create overlays. I am not sure where to look or what could be wrong.

The latest mainline u-boot + lamobo R1 patch does not appear to work when you try dhcp or ping on a Lamobo R1 (also known as Banana Pi R1) board. I wonder if the u-boot code needs to be modified to take care of the specifics of the GMAC/switch chip on a Lamobo R1 board. The defconfig for Lamobo R1 is the same as that for Banana Pi. Please shed some light to this issue. Thanks a lot. JLu

I have a Banana PI M1+ with latest Armbian Jessie with 3.4.109 kernel. The dmesg contains many rows like this ones ... [ 1468.309084] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev- instead. ... ... [ 2779.128724] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev- instead. ... I tried to search on Google without success. Can someone help me please? Thanks.

Anyone using any of those cheap bluetooth dongles? I have been trying to get it working but when connecting it freezes the OPi PC (the heartbeat led stops blinkng). The dongle is fine as it works on other Linux and Windows computers. This is the lsusb output: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 0…

Hi Thank you in advance for the help and the magnificent work ??Has "(BananaPi M1)" KVM kernel supports in Ubuntu Mate 16. I would like to virtualize Windows XP or Windows 7 in "(BananaPi M1)" a social project for non-profit. I'm about to go crazy is this compatible with this board (BananaPi M1) Thank you

Hi, as the title says while building this image i had this console reported error: E: Unable to locate package mali-sunxi-utils Also i would like to ask if there is hw acceleration(gpu) on xenial desktop images Thanks

hi, I made a program on Orange pi minus (kernel 3.X)using wpa_supplicant for wifi direct. That worked fine (basically). But i have been asked to do it on Orange pi plus with Kernel 4.9. The wifi works when i using nmtui, but when i made a iw list i couldn't find my material and i am not able to configure P2P. I think the problem is the kernel version and not the Hardware because my card with kernel 3.X works on orange pi pc plus. So i am a bit lost, what can i do ? My guest is to modify the realtek module ? I am not sure if i am on the right direction... Thanks, Ps: Sorry for my english.

Hello, I am experimenting with Orange Pi Zero and so I set different resolution with h3disp. Now TV connection via pin 9 is not working anymore. Any idea please how to reset to default setting? I tried many settings with SSH but it did not reenable my pin 9. Help is much appreciated.

Hi , I want to try out a project for a friend of mine and use an orange pi zero (for now , stronger model might replace it later) to do the following : have an outdoor ip cam connect with wifi on the orange pi zero Save videos on motion detect on pi`s memory Upload saved videos to a remote server (could be ftp) eg. every midnight with internet access via ethernet Keypoints : ipcamera must connect with pi`s wifi pi will connect to a router (via ethernet) a couple hours per day so the setup must not be internet based or with any extra equipment except the pi and the ipcam My thought of doing it : …

Hi, I read the docs but could not find out what to download to get a headless server. Getting Started says: "mainline: headless server, light desktop operations" In mainline there are 2 downloads for server (Debian, Ubuntu) and one for desktop (Ubuntu). I do not need a desktop, thus I do not want to waste space, RAM and CPU on anything related to it. May I ask, what to download or if there is no headless version what to do to remove the desktop-features alltogether? Thank you very much. Stephan

Hi, I am using the last image (kernel 11.5) for banana PI M1 and I successful use the nand-sata-install script. now I would like to copy the bootload to 128M SDCard Can someone help me?

Hi all and thanks for the great work done. I'm trying to install armbian on the eMMC of my NanoPi M1 Plus, the system boot from SD and I create the user then I start the nand-sata-install command. In the "choose an option" I have only "1 Boot from eMMC - system on eMMC" and then I choose ext4. The process complete and I launch the "dd if=/dev/zero of=/dev/mmcblk0 bs=1024 seek=8 count=1" command directly after. The system does not boot anymore with and without the SD inserted. On serial console, in both cases, I get: U-Boot SPL 2017.05-armbian (Jun 13 2017 - 15:14:45) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl…

Network block device support is not included in the 3.4 kernel on opi PC CONFIG_BLK_DEV_NBD Could this be enabled by default in a future update?

OPi.GPIO uses the GPIO Sysfs Interface for Userspace. I worked with the author to add Nano Pi Duo pin mappings including the built in button. The obligatory LED flasher for Duo: import time import nanopi.duo from OPi import GPIO GPIO.setmode(nanopi.duo.BOARD) GPIO.setwarnings(False) GPIO.setup(7, GPIO.OUT) GPIO.output(7, GPIO.HIGH) count = 0 while count < 20: print(count) GPIO.output(7, GPIO.LOW) time.sleep(0.5) GPIO.output(7, GPIO.HIGH) time.sleep(0.5) count += 1 GPIO.cleanup()

Hello! I have problems with Banana Pi and for today - updated all packages, and I can't connect via SSH nor FTP to my Pi. I have not changed anything, but there is automatic script which dist-upgrades the whole system, it is running once a day. Till 12.34pm CET everything was working fine - from logs, even I think till past 4pm I have connected via SSH to Pi, but then after kernel upgrade (seen note after logon) and reboot I can't access Pi in any way. I've tried to see logs: connect SD card to laptop with Linux to check if there is any problem, but didn't found nothing special. I've also tried to attach HDMI monitor but no signal. Seem…

hello, im use ARMbian on bpi m2 and will programming the gpio with python. i have tested with this little script, but i become a runtimeerror. i can not use the RPI.GPO. What can i used to programming GPO with Python under bpi m2?

Hi All, Can you please help me how can I set up OV5647 camera with Orange Pi One? Where can I find driver for it? Camera link: https://www.aliexpress.com/item/Orange-Pi-fish-eye-Camera-Night-Vision-for-Orange-Pi-PC-Zero-One-PC-Plus-Plus2/32864676943.html?spm=2114.search0604.3.26.74868de282hQoP&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_5015215_10059_10696_100031_10084_5015115_10083_10103_451_10618_452_5015815_10304_10307_10820_10821_5015915_10302,searchweb201603_16,ppcSwitch_5&algo_expid=44e91c9c-67e1-49b9-83f3-2c2890deab01-3&algo_pvid=44e91c9c-67e1-49b9-83f3-2c2890deab01&priceBeautifyAB=0 Thanks!

Hi, I'm using several Orange Pi Zero boards. At any given time, when I run "reboot now", I can no longer access the OPI via ssh. I tested the following distributions: Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113 Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113 All the programs I installed, which start from boot normally work, but I can not access via SSH. Is there any corruption of ssh files? Thank you for your help

Hello, I am trying to communicate with a mcp2515 breakout (8Mhz oscillator) on an Orange Pi Pc+ I have modified the breakout following info on Raspberry Pi: HowTo/Quickstart MCP2515 to keep logic level @3v I have two other nodes composed by two Arduinos, with same (not modified) breakout, one that transmits the other receives. I have successfully tested the first breakout (used on OPi) with an Arduino (powered by 3.3v and 5v on TJA1050). It lets me think that hardware is OK. Below photos of wiring (nb: orange wire becomes red, is wired near TJA1050 = 5v): It seems I have the same results with (edited) user_overl…

Hi everyone! I never asked for help at forums, but Opi forces my brain week. I try to create Wi-Fi by means of HostAPD(manual: https://goo-gl.ru/5s05). root@orangepi3:/etc# hostapd ./hostapd.conf Configuration file: ./hostapd.conf wlan0: Could not connect to kernel driver Using interface wlan0 with hwaddr xx:xx:xx:xx:xx:xx and ssid "MyWiFi" wlan0: interface state UNINITIALIZED->ENABLED wlan0: AP-ENABLED ........ (Infinite expectation) ############################# + dnsmasq does not want to work with wlan0, only with eth0. I will be glad if you help me, thanks!

Hi all together, on a Raspberry Pi 3b and 3b+ as well as on a Odroid-C2 I know how to switch off the blinking LEDs s or Power LEDs. Does anybody know how I can switch off or dim that extremely bright red power LED from the OrangePi3? I tried a script snippet like this: echo none > /sys/class/leds/orangepi\:red:\power/trigger But it wont work. Has anybody a helpful hint for an unpatient contemporary? Thanks for help :o)

Hi everyone, I connected my board with my PC via serial USB. Then I opened a serial with minicom and tried to test it out. I can send the strings from my board to PC without any problems but when I write something on the PC it sends garbage to my board. But, if I connect the TX, RX like: TX->TX RX->RX instead of TX->RX, RX->TX it sends normal from the PC and garbage from the board. I checked my baud rates but everything seems legit. I tried both 9600, 115200 bit rates, I also tried the both voltages (5V, 3.3V) What do you think could cause this problem? I saw this thread but seems like ther…

I believe that ethernet adaptor is not working properly because there's only one led blinking and its unable to receive ip address. I have tried to configure it with yaml files and manually with networkd and with static ip. I also tried to run dhcp on that interface and it received random ip outside of my network. Had no luck with network-manager either, it threw an error "ip configuration could not be reserved" With desktop image ethernet worked with no problem. So maybe there's a driver issue?

https://github.com/sicXnull/armbian-build/releases MXQ-PRO H313 https://github.com/sicXnull/armbian-build/archive/refs/tags/mxqpro.zip Summary: compile from source halts with error. Traceback (most recent call last): [🔨] File "/home/e***o/Downloads/armbian-build-mxqpro/lib/tools/patching.py", line 491, in <module> [🔨] raise exit_with_exception [🔨] Exception: Failed to apply 2 patches. Log uploaded and available at https://paste.armbian.com/dimokofipe Thanks in advance

Hello I have a BPi-R1 with Igor's 3.2 image (http://www.igorpecovnik.com/2014/09/07/banana-pi-debian-sd-image/) that runs as a router (with pppoe) and nginx/php5/mysql config for my wife's blog and also with ez-ipupdate for dynamic dns I have a nasty issue... once every 2 or 3 days, my board freezes for no aparent reason It does this even if root is on SD card (only sd card connected) or HDD (I have a modified mSATA adapter to get power from 3,3V SATA power connector... I removed the 3,3V regulator and added a thick wire from the 3,3V provided by the board through the SATA connector) Also I moved from this configuration: to this fan gpio controlled (witch was ver…

If I put a USB stick in I can see it in Nautilus(yes I installed nautilus) but when I click on the name of the USB , I get.. " Unable to access “USBNAME" Not authorized to perform operation (polkit authority not available and caller is not uid 0)" Everything else is working. I have Samba, SSH, x11vnc, NAS, HEVC x265 Video, all working happily.I can live without USB but I thought it would be important to give the Armbian developers feedback. I have looked for an answer and I do not see any one else having this problem. Once again I just love this Armbian / OPi.pc combination. Seasalt

Hello, i am having a problem with my Orange Pi the download speed is very slow. In Deluge and by wget i get normal DL speed around 9Mb/s (i have a 10Mb internet). But in JDownloader and in builit-in web browser i get around 100Kb/s. Any idea how to solve this issue? I want to make a download server using OPi but this issue is stopping me from doing that. I am running the newest Armbian Desktop

Hi guys, I'm a bit lost with this one. I want to setup a way of basically reinstalling a NanoPi Neo over the network. My thought process is: 1. Boot from NFS. 2. In the boot process have a script that runs the nand-sata-install.sh (or modified version of). 3. Reboot with new OS from USB. Now, I'm sure I can get this working, the bit that I am having trouble working out is how the bootloader will know if we should be loading from NFS or USB. Can UBoot grab this from the network? Ideally this will also be done without SSH access. I know this is a complicated problem but any guidance in the right direction will be really appreciated. Thanks!

Hello all, i can't see Banana Pi M1 on the available downloads on Armbian site where can i find it? if that exists of couse. Thanks

Hello Today i download Orangepi Zero Plus H5 Armbian OS then i tried gpio - i2c test but it's not work ... I did like this sudo apt-get install python-dev sudo apt-get install python-smbus sudo apt-get install i2c-tools sudo apt-get install libi2c-dev sudo nano /etc/modules -> add - i2c-dev, i2c-bcm2708 and i refer https://github.com/longsleep/linux-pine64/pull/17/commits/d915860a9c57a9a3ab3df7775c942ca205c8e16d this site i think adding I2C configs is not problem so give me some advice

I got my OPi PC2 last week and flashed the latest armbian server version. Every time I enter "reboot" on SSH to reboot the system, or plug in the power cable. The system can not boot up with a great probability. My power source is the charger for SAMSUNG smartphone. The specification indicates it can provide 5V/2A current. With the UART, I found the uboot process was stuck after the statement "INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9". The LED is OFF in that moment. After plugging out/in the power cable multiple times, the system can be boot up successfully finally and works very well. I'…

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Hello, I installed Armbian on Nanopi M1 Plus. I used it for a couple of days but now I encountered a problem: the boot stops after the following writing appears: "started hostname service" I tried to wait several minutes but nothing happens anymore Best regards Marco UPDATE: The problem occurs when the device is powered only by the Debug UART, probably the pc usb is not enough to power it

Hi all! First time poster, i apologize in advance for any etiquette violations... I have an OrangePi Zero H2+ board and the DS18B20 sensor (waterproof version). I have soldered the pullup resistor between power and data cables. I have Armbian Stretch 5.83 with 4.19.38-sunxi kernel. I have enabled the w1-gpio overlay and loaded the w1-therm driver. Data is on PD14 (GPIO 10), power is on 5v (tried also on 3.3v) I can see this in my dmesg: [ 10.371825] w1_master_driver w1_bus_master1: w1_search: max_slave_count 64 reached, will continue next search. [ 58.171052] w1_master_driver w1_bus_mast…

it appears the pins on the esp8266 12e are also on the orange pi one. Can I connect the pins to an armbian orange pi one and then test the esp8266 12e? I want to test if wifi works. Is required software present in armbian? Or should I get an usb adapter https://ae01.alicdn.com/kf/HTB1pm33XifrK1RjSspbq6A4pFXaf.jpg?width=1000&height=1000&hash=2000 and utilize a x86 gnulinux computer? It says the esp8266 12e supports i2c. Does the orange pi one have i2c pins, such that I can test the wifi of the esp8266 12e from an i2c connection on the armbian orange pi one? Is required software present in armbian? Thanks.

Hello Armbian team, I must start by thanking you for the effort you put into Armbian and making it possible for us to get the best of our boards. Your work is appreciated! The problem that I have been facing is that my OPI lite 2 functions correctly when it boots, but after a while I see a couple of sunxi-mmc errors in the logs and the filesystem becomes inaccessible and the board unusable. The log entries look like this: [ 750.827959] sunxi-mmc 4020000.mmc: data error, sending stop command [ 751.824422] sunxi-mmc 4020000.mmc: send stop command failed I cannot pinpoint the source of the problem as multiple issues seem to play a role in the…

installed wireguard on orange pi, configured the config, it works. It was necessary to restart orange, and after restarting it don t connecting to the LAN cable, even the orange light bulb is not lit. I start without sd, everything is fine. Reinstalled, installed wg again and the same thing again. What is the problem? OS:Debian11 (https://redirect.armbian.com/region/EU/orangepi3-lts/Bullseye_current)

Hi, This will be my first time using Armbian and OrangePi, sorry if theres stupid questions. I want to write a C++ application that uses LVGL to display information on a USB screen and have a few questions. 1) Will I be able to this screen in this setup. It uses the frame buffer (/dev/fb0). There are instructions for RaspberryPi, where its just plugged in and the frame buffer is available to use. 2) If I just use the latest Armbian Ubuntu version for this board what is the newest version of C++ I can use? (C++11/14/17 etc) 3) Is there a tool chain available to be able to cross compile my application (specifically from…

Hello! Brand new user here to the NanoPi Neo and even the forum. I'm planning to use a NanoPi Neo as hardware "interactor", the main idea is to connect a NanoPi Neo to a smartphone (Android or iOS), power the board from the USB cable and work in Host Mode to interact with de smartphone with libimobiledevice or adb. OTG does not support charging + data at the same time without a "special" OTG adapter. What I want to do is power the NanoPi by using the smartphone and even interact with it in host mode, like a regular computer will do, in simple terms, using a single cable, but getting power from it. Is this possible using NanoPi microUSB+OT…

Hello, On Orangepilite2, USB3 is recognised as USB2. I have connected multiple usb3 devices and results are same. I tried armbian, orangepi Debian, orangepi Ubuntu! results are same same too. For some reason all OS have same issue. In picture mass storage is USB3 device.

Hi, I am trying to flash debian jessie 4.x to NAND( there is already wheezy there ), but it doesn't come up in the ./nand-sata-install device list. I would install wheezy, but the problem is that it is not working( not 3.x or 4.x ), I just get a black screen after Staring Kernel message and the green LED is flashing every few seconds. What should I try next? Thank you, Stefan

Hi, First time user here. I'm using the legacy Jessie build with kernel 3.4.109 Kernel. OTG is enabled and generally working. However, with some USB devices we are getting the following message with dmesg: WRN:L2705(drivers/usb/sunxi_usb/hcd/core/sw_hcd_host.c):ERR: sw_hcd_schedule, best_end [ 663.633167] WRN:L2951(drivers/usb/sunxi_usb/hcd/core/sw_hcd_host.c):ERR: sw_hcd_schedule failed [ 663.641968] cannot submit datapipe for urb 0, error -28: not enough bandwidth This only happens with some USB devices. My USB headphones work fine but a USB DAC for music does not. I remember reading somewhere the OTG on the BananaPi seemed limited in terms of actual conne…

Hello. I'm using CubieTruck, Armbian 5.00 (Armbian_5.00_Cubietruck_Debian_jessie_3.4.110.zip). I installed and setup mpd, using spdif port and Tos-Link cable. Everything went well except the volume. The volume is too low to listen to the music. I can hear that, if I turn up the external amp's volume, but even I do that to the maxium, it still is very quiet. What can I do? Please give me clue. Thanks in advance~!

Hello, I am facing an issue regarding audio playback using the vanilla kernel( v4.5.2 ) for Banana Pi. There is no sound via the analog audio jack. aplay -l does show my playback device though. Here are some screenshots of my current config: speaker-test is throwing error: Should I need to configure anything else?

Dear friends, I have a problem with the ethernet connection of my orange pi plus 2e. The connection was working normally and stopped, I can only access through the wi-fi. I already researched it and found no solution. Open the connections and pressing ifupdown (eth0) the following error appeared: (1) Creating object for path 'org / freedesktop / NetworkManager / ActiveConnection / 14' failed in libnm-glib. Is there a connection to this error with a lack of ethernet connection?

Hey Guys, IM finally trying to make use of my OPi0 and Im planning on creating a daughterboard/hat/shield similar to the expansion board they sell, but with only the bits i need. One thing i'm wondering is if its possible to feed the power (5v) via the pins on the expansion board and not using the OTG input. Im trying to keep it as clean as possible and dont want to have the OTG connection for power. Is the regulator only on the OTG? Last I checked, my power supply gives out a steady 5.3v feed @5amps (driving some power hungry pixels). In regards to sound. I wanted to use an LMA386 amp on my custom daughter board to boost the output for a 4 ohm speaker i'…

I'm pretty new to Linux, so it could just be me doing something wrong, but I downloaded Armbian_5.34.171121_Orangepiplus2e_Ubuntu_xenial_next_4.13.14_desktop.img, put it on an SD card, and load it in the orange pi. The legacy installs fine but not this version. Before I even make it to the login prompt I get these codec errors: sun4i-codec 1c22c00.codec: ASoC: /soc/codec/analog@01f015c0 not registered sun4i-codec 1c22c00.codec: Failed to register our card Then after filling out the login info, adding a new user, it goes to boot to the desktop, but nothing happens, just returns me to the command line. After some mucking aro…

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Aud…

Hi Did a fresh install of Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.img on a Orange Pi Plus. Efter reboot, I did a apt-get update and apt-get upgrade, then rebooted... For some reason, wlna0 is no longer listed. I can do a "ifconfig wlan0 up", which brings up the interface - but so far I have had no success in configuring the wlan0 interface, neither by armbian-config nor nmtui I have even tried to edit /etc/network/interfaces and add: allow-hotplug wlan0 auto wlan0 iface wlan0 inet dhcp wpa-ssid "RG47C" wpa-psk "Secret!!!" but I am still not able to get it up and running. After …

Hello All, I have configured OrangePiR1 as router. There are three network interfaces, two as wired and one wifi(hotspot). eth0 serve for access to internet(via ppp/adsl) and eth1+Wlan0 for internal network. Interfaces eth1 and wlan0 are in bridge br0. Problem is, that interface eth1 sometimes loses connection/link(cable and switch were checked ). Next nonstandard behavior of eth1 is, that only yellow led control is blinking, while green led control is not alight. Network interfaces were configured via file /etc/network/interfaces. However, when I checked network manager nmcli, I saw, that some connections are configured there too (there can …

Hello Could You advice it` s possible to run emulator for SNES game on armbian at OPI WIN. I`m already run NES game but try to instal other SNES emulator don`t work Thanks in advance.

Hello, guys. I need help, don`t know what is going on. Yesterday two of my device`s (orange pi PC2) was rebooted by themselves. At different times, in separate areas. In log files I see fact of reboot but don`t see the reason. Temperature was in OK. Power adapter and micro SD card, which I use, in attachment. What should I pay attention? Can it be the reason is unattended upgrades or some armbian cron process? Environment: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.67 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=custom BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IM…

I have move system to emmc, and want to use sdcard to storage videos from camera. So I want to sdcard can automount/umount after hotplug. I have try to use udev to fulfill it. But it seems not work. I add a rules for udev at /etc/udev/rules.d: ACTION=="add",KERNEL=="mmcblk2p1",RUN+="/etc/udev/sdcard_hotplug.sh add /home/opi/Videos/sdcard %k" ACTION=="remove",KERNEL=="mmcblk2p1",RUN+="/etc/udev/sdcard_hotplug.sh remove /home/opi/Videos/sdcard %k" And add a shell file at /etc/udev/sdcard_hotplug.sh #!/bin/bash case $1 in add) mkdir -p $2 mount -t exfat -o iocharset=utf8,rw,sync,umask=0000,dmask=0000,fmask=0000 /dev/$3 $2 ;; remove) umount $2 …

Can someone post the printenv for a NEO PLUS2 because i think i f*** up my device and doesn't boot from SD or USB .... the only i get is the boot menu. Or any ideas to help me to fix this ?

hallo, for bananapim2 i can build jammy legacy and current, cli and xfce, on my pc-ubuntu-jammy. I just coppy bananapim2.eos to bananapim2.conf, removed box86 files while my pc-ubuntu-jammy seems have problems with build-script to download addition softaware from some git or ppa. Current-jammy goes off on boot on "starting kernel", but if i build with linux-sunxi-legacy.config renamed to linux-sunxi-current.config, boot is successful. On all builds i cannt becomme LAN over eth0, but wifi is ok. I can see eth0 and wlan on Networkmanager(cli too) and ifconfig. I tryed to disable all broadcom drivers i knew thru blacklisting, but wifi is working. Configuring NetworkManager a…

Has anyone managed to get video encoder working with the latest mainline kernel? I'm getting stuck trying to compile the cedar_ve kernel driver from https://github.com/uboborov/sunxi-cedar-mainline I have downloaded the kernel source using armbian-config and then built the sunxi-cedar-mainline kernel driver. However, I fail to load the driver due to version magic: When trying to force the load: But no dmesg message about magic check failure.

Hi there, I have OPi3 (not B nor LTS), now I got an SSD module ( https://allegro.pl/oferta/dysk-ssd-128gb-msata-6gb-s-13044566959 ), and it does not seem to work (nothing related in lsblk). I am using Armbian 21.02.3). Any ideas? the red LED is on, mechanically looks compatible with socket do I need something to enable this? armbianmonitor -u : http://ix.io/4Bkf

Hello Team, We are using H618 Allwinner SoC in which we have requirement to enable secure boot as per requirement. We have already checked couple of documents regarding secure boot enable but tools and scripts are not available to create Keys and other process using which secure boot can be enabled This project is based on the armbian image building system and is suitable for the Debian and Ubuntu image building projects of the Wildfire LubanCat (Luban Cat) Allwinner series boards. We are using allwinner-h618-gentoolinux build for build and development perspective. Let me know if need anything else from my end. …

I have Armbian running on Banana Pi R1 without networking access. Is this board suppported at all or it is just a waste of time?

Hi Igor, hi all, I use a BPi M1 and today I tested Igor's debian wheezy 4.1.2 image. It works really great. Thanks a lot. As mentioned in the FAQ I had a look at /etc/init.d/cpufrequtils. As written there it is possible to change the frequencies. The possible values are stored in "scaling_available_frequencies". The default value for "max_speed" in Igor's image is "max_speed=1010000". But this value ist not available inside "scaling_available_frequencies". "cpufreq-info -m" tells the current policy: frequency shoukd be within 480-960 MHz. 960 MHz is the maximum value in "scaling_available_frequencies". Normally BPi is able to run at 1008 MHz. How can I change…

I bought some 7 inch HDMI screen(800*480 manufacturer-Alientek) with USB controlled touch screen.( http://www.aliexpress.com/item/New-7-inch-USB-Capacitive-Touch-Screen-LCD-Display-HDMI-for-Raspberry-Pi-Pi2-Wholesale/32607731510.html ) HDMI screen can be displayed on Orange Pi One (Armbian 3.4.112-sun8i) using h3disp command. Touch screen could not work on Orange Pi, but that works on linux i386(4.2.0-38-generic). The symptom is as follows. Touch screen is defined ad /dev/usbdev*.* on Orange Pi. but on linux i386 is defined as hidraw device. (I will use uinput or uhid handing this touch screen). ==== orange pi ===== 1)dmesg [ 194.360084] usb 6…

With every upgrade I struggle with a "changed to default" login welcome message and have to do my modifications again. Therefore I would like to explain my changes and hope you can integrate them in the default version...: Your welcome message prints the $BOARD_NAME as ASCII art. Probably you have dozens of boards and can distinguish them in this way. So after login-in you directly see which board it is. I have only one type of "boards" (Cubietruck) and distinguish them by their hostname. So I have to replace "$BOARD_NAME" with "$(hostname -s)" in /etc/update-motd.d/10-header to identify my boards. What do you think about a change in that direction?

Hi everyone, i want to wake up orange pi on any gpio pin. Current i only can wake up from button on orange pi. There is a section of wakeup_src_para in fex configuration file, but when i append a wakeup_src with any gpio port, does not effect anything to wake up. how can i do?

Hi, I'm trying to put my OPI zero in mono instead of stereo by default. On ARMbian my alsa config file (/etc/asound.conf) looks like this : pcm.!default { type plug slave.pcm "dmixer" } pcm.!dmixer { type dmix ipc_key 1024 ipc_perm 0666 slave { pcm "hw:0,0" period_time 0 period_size 1024 buffer_size 4096 rate 44100 format S32_LE channels 2 } bindings { 0 0 1 1 } } ctl.!dmixer { type hw card 0 } I tried to add something like this but without success : pcm.makemono { type route slave.pcm dmixer …

Hi! Could you please clarify, is there a way to increase default limitations for max cpu freq (H5) on Orange Pi Prime? As i understand, according to driver (cpufreq-dt): /etc/default/cpufrequtils is a bit less restrictive: Is this a driver limitation ? Or there is a way to increase cpu-freq, but it's not used by default ? ( ... and why, if it is so ?)

Hi. I have received my new Neo Core and would like to flash my image to eMMC. I tried nand-sata-install but it says there is no target. On the Friendly Arm site they have a utility called eflasher, but I think this does not support Armbian. Is there a way to do it or a guide that I have missed? Thanks. J.

Hi there, I noticed there are up to date builds for Pine64 for Debian and also up to date ones for Ubuntu for the Orange Pi Win. But none for Debian and Orange Pi Win, newest ones are from November probably with legacy kernel? Is this just some kind of build script hiccup? If not, do you have an idea about a timeframe for new Debian builds? (I'd rather not use Ubuntu if it's just a few days/weeks I'd have to wait for Debian.)

Hello everybody! I would like to make a home media server with my HDD connected to Banana Pi (on SATA). I want to run Torrent client with WebUI, dlna and VPN server thereon. I`m stucked with fstab file configuration. First I tried to format my HDD`s partition to NTFS, every permission was good, but Transmission download, and FSTP file download was incredibly slow (4MB/s, but I have gigabit internet connection). The fstab configuration was this: UUID=<the uuid of the ntfs partition> /mnt/DataHDD ntfs defaults,auto,umask=000,users,rw 0 0 I`ve readed that, ext4 filesystem can be faster, so I decided to format the partition to ext4. After that, I changed…

Dear mainline developers, I'm writing a (mainline) SPI driver for de ads131 from TI which I would like to make use of DMA, on the orangePIzero H2, zero+ H3/H5 and nanopi NEO2+. On the 4.13.3-sunxi kernel (armbian 5.33), this works fine, the driver is automatically loaded when the associated devicetree overlay is loaded, and the DMA can be allocated. However, when I compile the same driver for newer kernels (4.14.17-sunxi, 4.14.39-sunxi, 4.14.67-sunxi armbian 5.59), the dma allocation no longer appears to work, while the SPI part of the devicetree is identical except for the phandle (checked with dtc -I fs /sys/firmware/devicetree/base on newest 4.14.67-sunxi kerne…

Issue found! Orange PI changed eMMC from KLM8G1GETF to KLM8G1WEPD. The difference is eMMC 5.0 vs 5.1 and maybe more. The key things is that Armbian (checked using 5.35 and the latest one) does not see this memory (fdisk -l)!! I have noticed it on OPI0 Plus 2 H3. PCB boards are the same, only memory model no. difference. Someone solved it or noticed the same? Confused 🤨

hey guys, Using legacy kernel I have trouble having dual output on LCD and HDMI. I tried to have a cloned dual output (same framebuffer for both) : [disp_init] disp_init_enable = 1 disp_mode = 4 screen0_output_type = 1 screen0_output_mode = 6 screen1_output_type = 3 screen1_output_mode = 4 fb0_width = 0 fb0_height = 0 fb0_framebuffer_num = 2 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 0 fb1_width = 1024 fb1_height = 600 fb1_framebuffer_num = 2 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 ... Also tried with 2 framebuffers : [disp_init] disp_init_enable = 1 disp_mode = 2 screen0_output_type = 1 s…

Hello, I can get 5.90 Bionic to boot, but Unifi needs an old mongodb. Stretch 5.65 worked in the past, but 5.83 will not boot. It hangs after "[ OK ] Started udev Coldplug all Devices." I've tried many, many times. Any idea what this means? I also can't get Stretch 5.65 to work again. It does not boot after a dist-upgrade

So I click load desktop and it completes that but when I try to enable it asks me if I want to enable autologin and it doesn't matter if I choose yes or no it just says killed, what's wrong? , i have an internet connection

Good evening, I ran into some problems with sbc-bench on a couple of Allwinner boards Orange Pi Zero, Orange Pi Zero+, Orange Pi One and Nanopi Neo 2 spcifically. The 7 Zip benchmark causes the following error: ./sbc-bench.sh: Zeile 611: 4206 Bus-Zugriffsfehler "${SevenZip}" b >> ${TempLog} Most likely due to a problem with the ZRam: zram: Decompression failed! err=-22 This happens on all boards under Debian and focal with different SD cards and power supplies. The benchmark ran previously on this setups without any issues – unfortunately I don’t know when it stopped working and hence cannot narrow do…

Allwinner_H3_Datasheet_V1.2.pdf up to five UART controllers In sun8i-h3-orangepi-pc.dts only 4 How do I use all five? serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = < 0x1c28000 0x400 >; interrupts = < 0x00 0x00 0x04 >; reg-shift = < 0x02 >; reg-io-width = < 0x04 >; clocks = < 0x03 0x3e >; resets = < 0x03 0x31 >; dmas = < 0x15 0x06 0x15 0x06 >; dma-names = "rx\0t…

Hi to all, I have been using banana pi pro and m1 for some years as mini PBX with asterisk, due the stop of bananian's development that works perfectly but now is obsolete and vulnerable, i'm testing armbian but registered prompt audio sounds choppy and i can't find reasons, I tried to move files in ram disk, use usb to lan interface, increase process priority, use performance ad cpu governor, also tried Armbian 5.83 Bananapi Debian stretch next, same problem. Any suggestion ? Thanks advance.

Hello! I try to connect to OrangePiPC by serial console. I tried using UART1 (add overlay & switch console to ttyS1), UART3 (ttyS3) and ttyS0 (debug port). But always I can see output (with kernel or ) but on my host computer (ubuntu 20.04) I see login prompt and can't enter anything. I tried change speed but not login. Even when I stop serial-tty@ serivice and start minicom without luck. Can you help me?

Hi everyone, Very green here. Basically I setup 1 of my orange pi a few months back with "Armbian_23.02.3_Orangepizero2_jammy_legacy_4.9.318". I recently bought another pi and wanted to set it up with a newer version. I see bookworm is now the latest. I have tried both CLI and Minimal but whenever I flash those into my micro SD the orange pi never boots up. My router doesnt see the connection, so it cant hand off an IP. I thought maybe it was a bad mini SD or a bad pi. But when I flashed the old jammy image into the same SD, the pi immediately picked up the connection, my router gave it an IP and I was able to log in as a root to the pi. I re…

sudo rmmod mv64xxx_i2c rmmod: ERROR: Module mv64xxx_i2c is not currently loaded root@WiPLUX-M040230BBQIGU:~# dmesg | grep -i i2c [ 0.846937] i2c_dev: i2c /dev entries driver [ 1.479459] sun8i-dw-hdmi 6000000.hdmi: registered DesignWare HDMI I2C bus driver [ 1.484185] /soc/i2c@7081400/pmic@36: Fixed dependency cycle(s) with /soc/pinctrl@300b000 [ 1.501006] mv64xxx_i2c 5002c00.i2c: Error applying setting, reverse things back [ 1.501095] axp20x-i2c 1-0036: AXP20x variant AXP313a found [ 1.502779] axp20x-i2c 1-0036: AXP20X driver loaded [ 53.381005] i2c i2c-2: mv64xxx: I2C bus locked, block: 1, time_left: 0 [ 55.429017] i2c i2c-2: mv6…

Dear all, I'm missing ttyS1 from the devicelist on my cubietruck with mainline uboot and debian Jessie kernel 3.18. Now i can not use my bluetooth module because it is not reachable. I've searched on the internet and the defenition of one (or more) uart port seems to be missing in the devicetree dtb file. Like in: http://forum.armbian.com/index.php/topic/382-armbian-on-pcduino3/ Has anyone fixed this for the cubietruck?

Did someone try to compile latest mysql 5.7 on cubietruck? I've got this error: In file included from /mnt/data/tmp/mysql-5.7.10/include/lf.h:20:0, from /mnt/data/tmp/mysql-5.7.10/mysys/lf_alloc-pin.c:98: /mnt/data/tmp/mysql-5.7.10/include/my_atomic.h:62:4: error: #error Native atomics support not found! # error Native atomics support not found! ^ In file included from /mnt/data/tmp/mysql-5.7.10/mysys/lf_alloc-pin.c:98:0: /mnt/data/tmp/mysql-5.7.10/include/lf.h: In function ‘lf_pin’: /mnt/data/tmp/mysql-5.7.10/include/lf.h:97:3: warning: implicit declaration of function ‘my_atomic_storeptr’ [-Wimplicit-function-declaration] my_atomic_s…

Hello everyone, newbie here just starting with armbian Recently I bought a cheap orange pi zero and I cannot connect via ssh through wifi. I read multiple threads regarding that issue however I cant say I understood everything I read. So, in a nutshell, is there any solution available? As many users reported, I can connect via ssh over etherner or wifi when ethernet is plugged in but not when only a wifi connection is available.

Hi guys, I just installed Kodi on my Orange Pi Lite running Armbian. Everything worked very well, except for the fact that that there seemed to be no audio at all through my tv. I am a beginner, so I really don't know what to do at this point. I saw someone talking about editing the /etc/asound.conf file so it will transmit sound through the HDMI cable. However, I have no idea how to open a file in the Terminal. I would love to (at least) know how to open a file in the Terminal. Thanks in advance, TheNooter.

I booted up my OPi0 + $2 expansion board this weekend after reading through the doc on it warning about TVout problems. Used the legacy Xenial 5.25 build available. I used the USB-serial method and logged in from my PC via SSH later over WiFi. On the TV there was no desktop GUI display, just the regular login prompts CLI. So this is not a RCA composite cable issue, but likely a display one...my TV is 720p. 1. On the TV I just got the login prompt after the text based Orange Pi Welcome screen. After logging in it stays text, as if I were in Terminal. I tried to install: $sudo apt-get xorg lightdm xfce4 tango-icon…

Hi after half a year using orangepi PC have upgraded system and it hangs when compiling headers.... After that have to reformat sd card and installed last version of armbian and the problem still remain when try to upgrade it... fresh system... đ then apt-get update root@orangepipc:~# clear root@orangepipc:~# apt-get update Hit:1 http://ports.ubuntu.com xenial InRelease Get:2 http://ports.ubuntu.com xenial-security InRelease [102 kB] Get:3 http://ports.ubuntu.com xenial-updates InRelease [102 kB] Get:4 http://apt.armbian.com xenial InRelease [14.1 kB] Get:5 http://ports.ubuntu.com xenial-b…

I found a problem about ethernet port leds in mainline kernel, legacy kernel is fine. the ethernet port has two leds, one is link-up (green), the another one is act (orange). In Normally, the green led keep light on when cable plugged in. And the orange led keep blinking when data coming or outgoing. but in mainline kernel (4.13.16-sunxi / linux-image-next-sunxi 5.35) ethernet port leds REVERSED. the green led keep light off when cable plugged in but light on when cable plugged out. I found that problem both in a new bought opizero and an old opizero. here is a short video record

Hello, I use the BananaPi M1 as network bridge with tranparent http proxy and filter with 2nd ethernet (USB adapter with AX88179 Gigabit Ethernet). But since latest update with kernel update, the network seemce to be go down often or the sytem is going bad. I can't find any solution and need some help. If you need some more information, please tell me what I should send. Thank you! Edit: The system is stuck on reboot... have to put of the power.

I was able to upgrade Armbian to 18.04 bionic beaver on my Banana Pi M1, and it's working (almost) fine! I used the command to update the sources.list to bionic: apt update && apt dist-upgrade -y && apt autoremove -y && apt autoclean apt install update-manager-core do-release-upgrade -d Fetched 403 MB in 8min 43s (769 kB/s) I gave "yes to all" to almost everything, except on replacing config files like KEYMAP, sshd and bind All these services I use are working correctly: network, SSH, bind, mail, cups, minidlna, SATA, USB printer, Samba This is not working: qbittorrent-nox 4.0.4 (misses libboost-s…

Hello, I'm looking for an efficient way to update the eMMC-memory of multiple NanoPi NEO Air's (roll out a production image). I was thinking about integrating my own image in to the eflasher from FriendlyElec but then found this possibility to access the integrated memory via USB-OTG and FEL. https://forum.armbian.com/topic/1580-nanopi-neo-air/?page=9 Wherefore basically two repos are used: sunxi-tools fel-mass-storage I tried following the instructions, build and installed the sunxi-tools (sunxi-fel) and used "dd" to copy "fel-sdboot.img" to an empty SD card. For testing I took a brand new NanoPi NEO Air, connected UART0 with my P…

Is the build for Orangepi Plus the same for Orangepi Plus 2? When I download for OPI Plus 2 I get the following file: Armbian_5.65_Orangepiplus_Debian_stretch_next_4.14.78 but it will not start

Hello. When my orange pi zero is booted, Pin16,18(PA19,PA18) seems to record high value(3.3v) I want the pins to stay low. In the dtb file, PA18 and PA19 are assigned to i2c1 and i2s0. But in the /boot/armbianEnv.txt file those overlays are not enabled. Can someone please help me how to keep ping 16 and 18 low at t he boot time? Image used: ARMBIAN 5.38 stable Ubuntu 16.04.4 LTS 4.14.18-sunxi Thank You.

Hi! Just saw a new board from FriendlyARM - NanoPi R1 (https://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=248). It based on Allwinner H3, has dual Ethernet port, wi-fi and Bluetooth, USB, and onboard eMMC. Memory options are 512MB or 1GB. It comes in a case, just add power supply. Looks quite fun SBC for IoT and for micro router. I was unable to find Armbian images for this board. Could you please comment if is it possible to use images for other Allwinner H3 boards? Do you have any plans to support this board? Thank you in advance for your comments!

So when I try to run the Buster image for Olinuxino64, after the initial U-Boot screen it spends some excessive time with lines Starting version 241 (about a minute or two) Begin: Running /scripts/local-premount ... Scanning for Brtfs filesystems. done. (many minutes. Does it have anything to do with the fact I have some old data on the on-board eMMC?) These appear on the splash screen with armbian logo via HDMI, not on the serial console. When it finally boots, USB keyboard is not working (nor USB in general, dmesg shows nothing when i try to plug/unplug various devices) and the system is very unstable... It took me several times to even run armb…

Hi, i tried to get an infrared transmitter working, but without success. An /dev/lircX device is never created. I'm using an NanoPi Neo and want to use lirc. The pwm_ir_tx/gpio_ir_tx modules are loaded but i can't see a device. Can anyone help me? Best regards Joachim

Current community builds(Debian 12 and Ubuntu 24.04 as well) doesn't support audio codec. Even after enabling codecs with armbian-config ls /dev/snd command displays: seq timer when expectation is to have by-path controlC0 pcmC0D0c pcmC0D0p seq timer Have anybody face with the same issue? any advises how to solve it?

Hello! I am trying to get the cedar_ve device working for OPIZ2W. I am currently running this image: Orangepizero2w_1.0.4_ubuntu_noble_server_linux6.1.31 My uname -a: Linux orangepizero2w 6.1.31-sun50iw9 #1.0.4 SMP Wed Oct 9 13:39:53 CST 2024 aarch64 aarch64 aarch64 GNU/Linux To do this I am trying to follow these steps: 1. Modify a dts for OPIZ2W to include cedar_ve. 2. Donwloan cedrus driver and build it. 3. Compile modified ffmpeg with x264cedrus support Have anyone tried this? I have only found builds for recent kernel for the H3 CPU, none for the H618. I am looking for a DTS that su…

The FAQ says the username is "root" and the password is "1234", but the password for the root user on at least the image in Lamobo-r1_Debian_3.2_jessie_4.1.2.zip is "pi" (apparently also the default bananian password). edit: nope, I'm just an idiot. The docs are right. Sorry! Don't see a way to delete this topic, but I would if I could.