Allwinner sunxi

Hi, just a quick question: Why is OTG disabled? I read some "performance issues" or "high CPU usage by OTG" etc... But can someone be more specific?

Hi, I use a Cubietruck 3 and the last Debian "Armbian_5.25_Cubietruck_Debian_jessie_default_3.4.113". 1° When i'm sart for the first time, It's impossible to reboot or halt the cubietruck. The led Green and blue flashes always. I must I have to remove the power connector for a reboot 2° Idem whem i have make an update and a upgrade 3° When creating the account at setup, I want to use "ac-news". The created account is actually "acnews" without the "-". Before posting, I tried several times the installation by writing a new image on the SD. I always have the same worries Thanks François A track: if I make a first installation with an Armbian_5.20_Cubietruck_D…

For some reason the reboot command doesn't appear to reboot the H3. Is this because it doesn't have a PMIC in the same way that the A20's do or is it just a case of the correct assembly instruction not being called?

I'm powering a small PCB via the OTG port on my OPI PC Plus, however sometimes I need to be able to reboot the device. It is possible to cut power to the OTG port momentarily to force a reboot? I've seen mention of PL2 GPIO, but it is unclear to me how this should be setup. I've also looked at uhubctl, but that didn't work. Thoughts?

I have an issue with the latest releases since Yammy on a Orange Pi Zero LTS. Reboot is not working (system shuts, but not starting again)

The sytem acted a bit wierd, so I rebooted it. Since the moment, the server did not launch, rebooting itself again and again. I edited boot script to get more informations, and this is the moment, where the sytem gets stucked before it reboots (I have panic set to 180, so this screen is visible for around 3 mins). Banana pi M1 armbian 5.14 installed on SDcard and HDD This is not PSU error, since other distros are running smoothly. This is not SDcard error, since I dded this SDcard to another and tested it.

Hiya, Using a Banana Pi M1 as a factory production tester in China, running Armbian Mainline 4.6.3. Works fine here; never had the problem they're reporting, but they're saying: a) after a certain amount (unspecified) of time the boards crash and get stuck in a reboot loop displaying screen as shown in JPEG - "kernel panic not syncing - Attemped to kill init! exitcode=0x000000b" b ) rewriting the SD card image (from one I provided; a 4GB pre-configured image) fixes it (until it happens again) c) Only useful thing I can get from the photo attached is that the stack trace in the image (which is all I have to go on btw; trying to get a copy of the ba…

I have just received an Orange Pi PC Plus, and am mostly happy with it. Linux orangepipcplus 4.14.18-sunxi is installed on a microSD card. There is a minor problem with IP addresses. When I first turned it on I forgot to plug in the network cable, so naturally ifconfig showed no IP address. I plugged in the cable, waited a minute, and tried again. Still no address. Maybe it's not hot-pluggable. Reboot, and I got an address. Since it was outside the range my server accepts I assigned a static address in the router, and rebooted the router. ifconfig still showed the first address, even though the router's client list showed the new …

Hi, I have from the very beginning problem with the reboot command and the reset button on the Orange PI ONE. > The reboot command take down the PI ONE, but it dont get up again. None of the led lights give any sign... so it just dont kick in? > The reset button, is just not responding... I can press it any time... no affect. Any good Idea to figure out where to search for the solution? You can check my log under; http://sprunge.us/iJDe Thanks in advance /R

When I do a reboot the Olimex Lime2-emmc shuts down. No more information is shown on the display. This happens with the latest Armbian_5.31_Lime2_Debian_jessie_next_4.11.5 image from the website. It also happens with a self-build image with u-boot v2017.07 and v2017.05 Any ideas? Or debugging directions? I am out of options after 2 days...

I have had similar issues what somebody had on this forum but I cannot post reply because the topic is closed. But I found solution. You need to downgrade u-boot with following commands. For Olimex Micro: apt-get install linux-u-boot-next-micro=5.60 Tested on ARMBIAN 5.60 stable Ubuntu 18.04.3 LTS 4.19.84-sunxi For Olimex Lime2: apt-get install linux-u-boot-lime2-emmc-next=5.30 Tested on Ubuntu Bionic with Armbian Linux 4.19.81-sunxi

I remember there where a problem before, shutdown leads to reboot. But now it's the opposite - reboot leads to shutdown. Both gui button or: sudo reboot reboot sudo shutdown -r now sudo init 6 from terminal, or ssh, behave the same. This is on Armbian_5.25_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop / Armbian_5.25_Orangepione_Ubuntu_xenial_default_3.4.113, from download section and self built.

Hi I have added some drivers in the kernel source code in the cache folder and I am not sure how to rebuild the kernel with the new changes. I am trying to rebuild the mainline kernel. Using compile.sh overwrites the changes with default files. I have changed the following configurations in my config file. KERNEL_ONLY="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 3 KERNEL_CONFIGURE="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 4 CLEAN_LEVEL="" # comma-separated list of clean targets: "make" = make clean for selec 5 # "debs" = delete pac…

The built-in WIFI module doesn't switch to monitor mode. This makes me looking for rebuilding the module from the Git repository: https://github.com/rdm-dev/rtl8189ES_linux/tree/52ee6388111fbaf990ec60e93b086cafa6cc373a I am stuck with the following error: *** No rule to make target 'arch/arm/tools/gen-mach-types', needed by 'include/generated/mach-types.h'. What is necessary to rebuild and replace the module with a new one? Here is what was done so far: root@orangepiplus:/usr/src/rtl8189ES_linux# uname -a Linux orangepiplus 3.4.110-sun8i #18 SMP PREEMPT Tue Mar 8 20:03:32 CET 2016 armv7l GNU/Linux root@orangepiplus:/usr/src/rtl8189ES_linux# dmesg |grep 8189 [ 3.…

hi we are using legacy armbian xenial desktop wich work great with most rtl based dvb-t tuners we would like to add a new rtl2832 usb tuner with specific vendor id to be recognized : using x86 pc first we patched dvb-usb-ids.h with new vendor id then compiled and installed media_build ,result is success & dongle working well using orange pi one : building media_build give error . is there a way to patch the new vid thanks

Please give me your recommendation for my OPiPC+ to use Armbian and Asterisk I see there are 3 options for Armbian for my model. I am not good with linux and would prefer a GUI for both Armbian and Asterisk. Also I am wanting as "Lightweight" as possible. I will not be using the OPi for anything else but a phone system. Also could you give me steps to take to add Asterisk to Armbian. Thanks

I am looking for a working python "wiring library" for the NanoPi Air.... With pyGPIO i have limited success. Only GPIO4 seems to work. Just a quick "use this libray for python..." please. I need 3 GPIO pins (and UART1 which is working well under python...) Thank you!

Hi there, I want to build my product on Orange Pi Zero Plus2. I want to put it to enclosure and leave just power connector accessible. But I found this scenario - if user makes mistake in his wifi settings and then he saves these "faulty wifi settings", he will not be able to recover default wifi values anymore. How would you solve this? (the best approach without any additional buttons for gpio pins or additional elements)

Hello, The system changed to ro during update. The armbianEnv.txt file has been corrupted and is empty. I'm looking for how to create it again ... and I can't find it. Can you help? edit: I try to do it myself, but I don't know if that's all. verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay-prefix=sun7i-a20 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u edit: Overall, there were no problems at 5.3.9. During the update to 5.4.20 I broke down. The worst thing is that I'm not in the location : / edit: Search result: it's ok ?

Hi guys, today a archive to run an orange pi one with a 5v dedicated power ac (not usb one used for smartphones). i try either official. Ubuntu ldxe image and armbian (burned with etcher on Samsung sd) On my first try I saw on my 720p TV (hdmi) some write then nothing else, no signal. And a green led lights up with a red led blinking. on next tries no video signal at all and only the red led is still light on. I can't try android img cause phoenixcard app give me error. Is there something I could try? Thank you or just you can tell me what that leds means

Hi armbians, I was wondering how do you trigger the red LED for other devices like USB r/w or wifi tx/rx . echo mmc0 > /sys/class/leds/orangepi:red:status/trigger works like a charm for microSD r/w. I want to trigger it for my wifi interface which is "wlx0013ef6d5c23" . Any thoughts? Detailed log uploaded at http://sprunge.us/gCjP

I have an orange pi light I loaded two sd, one 16GB and one 32GB with "Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img" I can not see any mistakes in the console: https://pastebin.com/HXyeQkjr I tried various resolutions. Still, the screen remains red and nothing appears.

Hello: I have an issue with one of my opi pc boards: When I connect it to hdmi tv and tv is not connected (switched on before booting the soc), I get just a red screen. Armbian is up and ready. I can log through ssh. Tested in Armbian_5.38_orangepipc_Ubuntu_xenial_default_3.4.113_desktop and openelec (last version). Same problem in both. I'm looking for mods in the .fex file (if there are any that applies to this case). So far I checked http://sunxi.org/Fex_Guide without luck. Time ago, I had a similar problem with an raspberry pi. In this case it was solved with a parameter in the config.txt (hdmi_force_hotplug=1). With thi…

Hello, Do you guys have some tips on reducing power consumption to an absolute minimum? I've made some progress and reduced it to about 500mW on idle. with some CPUs shut off. I would like to get it lower for battery saving. I'm currently building a custom image with as much of the functions I don't need (SPI, i2c, bluetooth etc) turned off hoping that I will get some more power savings. Not sure if this will make a difference yet. Ideas would be appreciated!

I would like to connect reed switch to OrangePi Zero with H2 processor. Can I use this? https://github.com/duxingkei33/orangepi_PC_gpio_pyH3 Under examples, there are two examples I think I could use: - read_button.py - read_key_PG7.py I have two questions. 1. Where is the pinout? read_button.py has this code: led = connector.gpio0p0 # This is the same as port.PH2 button = connector.gpio3p40 read_key_PG7.py has this code: led = connector.gpio1p38 # This is the same as port.PH2 button = connector.gpio1p40 #CHOW Which pins are which, where to get the picture of GPIO pins? (And why LED's…

Hi @Igor you should consider changing imagetool when you ship your image files since the Suse image tool is quite broken on Windows platforms 8 or higher since its often just gives a blank non function interface that crashes upon pressing buttons. Perhaps Rufus would be a better alternative

Two days ago I upgraded the kernel to 25.5.1 (6.12.30-current-sunxi) from 25.2.3 (6.12.20-current-sunxi). Since then I have no longer been able to play a certain title (FLAC file) in mocp. In case it's relevant, the title is: "Malukah - Awake (The Dragonborn Comes)". Symptoms: dmesg starts showing kernel trace output at 1:43 of the song mocp finally stalls at 1:52 and it's impossible to interact with it from that point on Is there anyone here who would be able to provide pointers on how to debug this? I am a developer and I have done some work with Yocto/OE before and wouldn't be afraid to get at this with a debugger. Since it's nice…

Hi igor, when are you going to release the next version (4.1.15) of your debian based image? I wait for it to be able to set up the testing server soon for a new system. Thanks in advance for your contributions and for your efforts Best regards, ireng

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

Hello everyone ! I'm facing a hard issue that I still cannot solve. On my Raspberry, on Raspberry Os, to be able to use Rustdesk (https://github.com/rustdesk/rustdesk, an open source Teamviewer ) I needed to add some tweaks to the /boot/config.txt file: hdmi_force_hotplug=1 (See doc) hdmi_group=2 (See doc) Now, I'm trying to replicate these behaviours on Armbian for Opi zero 3 (but it could probably work for all Allwinner cpus if a solution is found) When looking on the Armbian documentation for Sunxi, I've found this (See doc) : For example to always use the hdmi connector, even if no cable is inserted, using edid info when available and …

Hello I`m download newest version Armbian desktop for my Orange Pi. Install the following packages sudo apt-get install tightvncserver sudo apt-get install xrdp But I have error when I want connect to desktop from my Windows 7 Additional I try to connect use VNC Viewer but resulution is small and visual desktop is other the wwhen I`m normally attach HDMI monitor to OPI.

I want to put a banana Pi M1 plus a 2.5" SATA drive in a plastic box with only the ethernet and USB ports exposed. This means the onboard power button is not accessible to boot the board. Are you able to power on the board using the GPIO pins? If so please could someone advise which pins to connect to? I also aim to put a 5.5 x 2.1mm barrel connection on the box (with a latching press button switch for isolation) for the +5v supply and connect a short micro USB connector from the barrel socket to the board and also attach the SATA power leads directly rather than powering from the board 2 pin connector to take the load off the micro USB input.

Hello, I've just found a topic about removing Allwinner legacy. I work with Orange Pi PC Plus board, H3 CPU. Do I understand correctly that the option to build system based on old v.3.4 kernel will be removed? Once I experienced a problem with system shutdown using newer kernel - got System halted message. This is why I decided to continue with legacy kernel. Please advise.

I have an Orange Pi Plus 2 that was running Armbian off of its onboard eMMC module, but I think I may have damaged it while working with the GPIO pins as it now will no longer boot from the module. The board will boot and run OK off of an SD card, but I'd like to copy the OS back to the eMMC module if possible. I've tried to rerun the script 'nand-sata-install', but I receive the error 'There are no targets. Please check your drives'. If I list the mmc devices I just get one, which I presume is the SD card: > ls -l /dev/ | grep mmcblk brw-rw---- 1 root disk 179, 0 Mar 20 16:51 mmcblk0 brw-rw---- 1 root disk 1…

Basic information: Board: Orange Pi Plus 2e Image: Armbian_19.11.3_Orangepiplus2e_buster_current_5.3.9.img Issue: No sound on HDMI output There has been quite a few suggestions for this issue here and and OrangePi Plus and none works for me. Tried following: 0. sudo apt-get update && upgrade 1. Created and Changed /etc/asound.conf Version 1: pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } Version 2: pcm.!default { type hw card 1 device 0 } ctl.!default {…

I have orange pi zero board ..i searched a lot for changing boot splash screen ( currently "armbian universal operating system" which is enabled by adding bootlogo=true in armbianEnv.txt ) I have tried Plymouth it is not working After searching lot i knew about if we can replace bootsplash.armbian , it can help because then neither we need to change uboot packages nor we have to add quiet splash like words etc in armbianEnv.txt. https://github.com/armbian/build/tree/master/packages/blobs/splash. With help of this bootsplash-packer Can anyone list me some steps ( in short ) How to run this script and create…

Hello, In additional items of v4.1, auto system update via repository apt.armbian.com You have written and has been added, if you have upgraded from v4.0, source.list of apt does not seem to have been updated. If the contents to be updated would be what kind of configuration information? I want you to tell me. Environment: -Debian jessie 4.1.4 -Cubietruck Best regards.

Hi, I'm getting going with a pile of Nanopi Neo's and am using the jessie server image with the legacy kernel I'm having trouble with the repositories - I see this error when using apt-get ... W: Failed to fetch http://apt.armbian.com/dists/jessie/InRelease Unable to find expected entry 'jessie-utils/binary-armhf/Packages' in Release file (Wrong sources.list entry or malformed file) I saw the discussion in http://forum.armbian.com/index.php/topic/1834-repository-management/which says the problem has been fixed ... but, er, it does not seem to be. Any ideas welcome on how to sort this out. Thanks Jason

Banana Pi M64 http://www.banana-pi.org/m64.html the default ubuntu os is crap, requesting for an armbian build Allwinner a64 2GB RAM

Hi everyone, I'm using the Orange Pi Zero 3 and would really appreciate a lightweight desktop image with just the XFCE desktop, a web browser, and basic tools (like file manager, terminal, etc.) with video acceleration. The current Armbian desktop image works, but it includes a lot of software I don’t need. I’m looking for something more minimal — just enough for light use and a faster experience. Does anyone have (or know how to build) a stripped-down XFCE image for this board? Thanks in advance!

I use one of my Cubietrucks to operate two IR-read/write heads to read out powermeters. Sometimes some kind of error happends and the device get's disconnected (not physically, but from system): dmesg output: [434913.929842] ohci-platform 1c14400.usb: frame counter not updating; disabled [434913.939546] ohci-platform 1c14400.usb: HC died; cleaning up [434913.947863] usb 3-1: USB disconnect, device number 3 [434913.949632] cp210x ttyUSB0: failed set request 0x0 status: -19 [434913.959197] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [434913.959273] cp210x 3-1:1.0: device disconnected I can fix it by rebooting only, also unpl…

I am using an A20 micro with an old 10" LCD from Olimex, now discontinued, A13-LCD10TS All is working without problem but no touch screen. In old Olimex Wheezy image, touch screen was working with tslib. In new Armbian Jessie image there is no tslib and touch screen is not working. Also using modprobe ft5x_ts as suggested in this forum give an error message modprobe: ERROR: could not insert 'ft5x_ts': Operation not permitted FEX file seem correct and is same as old FEX used with Wheezy What I am missing? Regards Franco Spinelli

Hello. Is there a way of resetting the USB subsystem in Armbian for Orange Pi Zero? I don't want to unplug and plug a USB device or reboot the system just to reset the plugged USB devices. The above is doable on a PC running Ubuntu with something like this: $: cd /sys/bus/pci/drivers/ehci_hcd $: ls 0000:00:14.0 bind module new_id remove_id uevent unbind $: echo -n "0000:00:14.0" > unbind $: echo -n "0000:00:14.0" > bind Wondering if something similar (I don't really care if the solution is not similar) is doable on Armbian for OPIZ. Cheers!

Hi everybody, I recently purchased a Orange Pi Zero since I needed a tiny board, and after setting it up I noticed that the resolution didn't fit properly in a portable TV I was using. Doing some research (I'm a complete newbie), I found the command "h3disp" ot change resolution on Armbian for H2+ and H3 boards, so I gave it a try. Now it's completely black and no signal on AV IN. Thanks to a post in this site, I noticed that every command in h3disp was for HDMI outputs and that doesn't fit Orange Pi Zero since it supports PAL and NTSC only, so now after changing between 480i and 576i doesn't seem to be showing anything at all. I was wondering if I could restore…

Hi everyone! I'm looking for an old image of Cubieboard with legacy kernel 3.4 . Someone can help me? I've searched into main site and forum but can't find anything. Thanks

Wondering if there's anything similar to retroarch or mednafen that'll work for armbian on a pcduino3? I can't get the former to compile/install and the latter gives me guff about not being able to find a GLX visual when it tries to load video. It's worth noting that I'm pretty green when it comes to Linux, especially when it comes to "exotic"/SoC builds. I have nothing against learning, but I've found the signal-to-noise ratio for this product in particular is very poor and a lot of the info is woefully obsolete.

I installed the image Armbian_20.08.1_Orangepiplus2e_focal_current_5.8.5_desktop.img on my Orange PI Plus 2E and I installed RetroArch to setup a retro gaming board. Everything installed ok but all games even weak games like for Super Nintendo, are running slow and no audio, does anyone here already tried to get RetroArch working on this board? Audio is not working , it uses pulseaudio and it's installed already. I already tested RetrOrange Pi image, it uses Armbian too I guess, most of the games runs at full speed, the reason I am not using is that is a little outdated, some emulators doesn't work and some are missing and I personally …

The Problem is retry count exceeded... I don't know why is this happening to me. I search the older post the same problem, but i don't know what is the exactly problem. My board is CubieTruck3 A20 Board and i use SD Card.

Hello! I'm planning to try using kodi with my cubietruck. Should I use desktop ubuntu image, or can I customize the legacy debian one? One those things is returning memory reservations. If I get it right I should edit uboot config and add: sunxi_ve_mem_reserve=128M cma=128+16M Am I correct? Are there any other changes I should change in default config to run kodi smoothly? I'd go with debian if it's possible, but I can switch to ubuntu, if there's alot to change in 3.4 debian image.

Hello! I am tired of system freezing once in 1-2 days, and think the reason is heating (Board 49 degrees right now) so I decided to revert system back to SD and not use HDD at all, making system more stable by power and temperature. Please help me to do it - is there any revert script that I can run to move all data from HDD back to SD?

I have an Orange Pi Plus 2 that has worked with Android installed for a long time. But now I needed to install Linux on it. I needed to find a Linux image to install on it, and I've already got several, but all the ones that worked, and that were on the login screen, didn't go beyond that, since in none of the 4 USB ports the keyboard worked and I imagine the mouse. I read somewhere that the image Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z or Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112_desktop.7z, but I don't know where to get it, hoping to solve all the problems. Can someone give a helping hand, please?

Hi all. I've got an issue trying to use Bluetooth and RFCOMM. My system is: Cubieboard2 running latest img and updated with apt-get update/upgrade: ____ _ _ _ _ ____ / ___| _| |__ (_) ___| |__ ___ __ _ _ __ __| | |___ \ | | | | | | '_ \| |/ _ \ '_ \ / _ \ / _` | '__/ _` | __) | | |__| |_| | |_) | | __/ |_) | (_) | (_| | | | (_| | / __/ \____\__,_|_.__/|_|\___|_.__/ \___/ \__,_|_| \__,_| |_____| Welcome to ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 4.9.12-sunxi System load: 0.07 Up time: 30 min Me…

Hello everybody! Can I read data from the RFID-MFRC522 module with my NanoPi, if so, tell me what python libraries are in Armbian or will it be necessary to install an official ROM and work through RPi.GPIO?

Hi, can anybody tell me, why the rights on the serial port ttyS0 are R/W for the user (root), but only W for the group (tty) ??? crw--w---- 1 root tty 251, 0 Jan 24 19:45 /dev/ttyS0 Hardware is orangepi one, OS is Linux pi-one 3.4.113-sun8i #6 SMP PREEMPT Tue Jan 16 14:36:25 CET 2018 armv7l GNU/Linux I can change the rights with chmod, but the change is not permanent after a reboot. L.

Hi, I am using the Ubuntu desktop image found here https://www.armbian.com/orange-pi-prime/ I am able to start the board, it lights up and connects to the network via ethernet -- I see it come up in my DHCP table and am then able to connect via SSH Docs say to use root:1234 for login, but I get Access denied. I found another forum post that says root is disabled via SSH by default. When I try to connect locally, I get no video from HDMI so I don't know what it's loading up to. I had hoped to be able to configure via SSH but can't get in. Any ideas on how I can proceed? Thank you!

Hi there, after upgrade Armbian today the Device (banana-pi) doesnt come up again telling that the root fs couldnt be mount because mmcblk0p1 is not available. After checking SD Card everything seems ok, filesystem is there and doesnt have any error. But still no boot. Then after applying a backup things are fine again. Started the upgrade again and same error like before. When applying those two updates there is repeatedly a dead system afterwards. Tested on different devices now. root@gluster01:~# apt list --upgradable Listing... Done armbian-config/unknown 25.5.0-trunk.330.0402.205255 all [upgradable from: 25.5.0-trunk.286.0324.065110] linux-ima…

hello everyone ! How to get totally permission in /root folder of my orangepiplus2 under armbian? I have already set sudo su ----pass ok I'm installing WiringOP and I have to go inside /root Using psw I know the path that is /root/WiringOP Then I type chmod +x /.build and then /.build but I don't have permission . Opening the file system I see the "X" over the root folder Could I have the totally control of armbian ? Thanks !

Hello! I'm using Wheezy under kernel 3.4.x on Lime2 with 7" LCD and i added fbcon=rotate:1 in boot.cmd and the console booted in portrait but LXDE is still in landscape. I also added FBDEV_ROTATE_CCW=90 but with no results. I can rotate the screen from the /usr/share/X11/xorg.conf.d/XX-fbturbo.conf file but every time i touch the screen the LXDE crashes. Any suggestions please how to rotate the screen in LXDE? Thank you!

I have an ap in banana pi whose ip is 192.168.4.1. And eth0 on banana pi whose static ip is 192.168.144.100. I would like to connect device A from banana pi's ap and also it can ping to the eth0. So far I had tried: sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE sudo iptables -A FORWARD -i wlan0 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT sudo iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT

OPi.GPIO uses the GPIO Sysfs Interface for Userspace. I worked with the author to add Nano Pi Duo pin mappings including the built in button. The obligatory LED flasher for Duo: import time import nanopi.duo from OPi import GPIO GPIO.setmode(nanopi.duo.BOARD) GPIO.setwarnings(False) GPIO.setup(7, GPIO.OUT) GPIO.output(7, GPIO.HIGH) count = 0 while count < 20: print(count) GPIO.output(7, GPIO.LOW) time.sleep(0.5) GPIO.output(7, GPIO.HIGH) time.sleep(0.5) count += 1 GPIO.cleanup()

Hi orange pi +2e with Distribution: Ubuntu 16.04.2 LTS Kernel version: Linux 3.4.113-sun8i armv7l rpimonitor installed with sudo armbianmonitor -r I use Rpimonitor to control temperature, upgradable packages and cpu frequency, nice tool ! Unfortunately it looks that rpimonitor has access to my external external hard drives, so no spin off . I change rpimonitor config files sudo nano /etc/rpimonitor/data.conf #include=/etc/rpimonitor/template/sdcard.conf and sudo nano /etc/rpimonitor/template/Allwinner_H3_Extended_Mainline.conf #dynamic.7.name=externaltemp #dynamic.7.source=/tmp/externaltemp #dynamic.7.regexp=(.*) #dynamic.…

Running "sudo armbianmonitor -r" fails with this output: Installing RPi-Monitor. This can take up to 5 minutes. Be patient pleaseE: Unable to locate package rpimonitor /usr/bin/armbianmonitor: line 694: /usr/share/rpimonitor/scripts/updatePackagesStatus.pl: No such file or directory Now patching RPi-Monitor to deal correctly with H3 Now you're able to enjoy RPi-Monitor at http://192.168.11.149:8888 It isn't possible to access RPi-Monitor on http://192.168.11.149:8888. The folder /usr/share/rpimonitor does not exist. This is on a Nano PI Neo Air board with freshly installed "buster". (would have included armbianmonitor -u output but that g…

Hello, I know this is slightly the wrong subforum... I'm using an OrangePi PC2 with ARMBIAN 5.34.171109 nightly Ubuntu 16.04.3 LTS 4.13.11-sunxi64 I tried installing rpimonitor using rpimonitor -r after creating a "pi" user and a "pi" group That part worked. Afterwards, it told me that the webserver would be available at 192.168.0.xxx:8888 I tried that. Surprisingly, not the customized version of OrangePi-Monitor appeared, but the "original" RPI Verison. I fixed that copying /etc/rpimonitor/template/OrangePI_xx.conf to /etc/rpimonitor/template/data.conf. After restarting, it actually works, but placeholde…

Hi everybody! We have an application that uses RS-485 and we decided to use the OMAP UART implementation, but it doesn't seems to work with Cubieboard A10. We tried to enable in userspace, by calling ioctl and also via dts file. ioctl (C code): ------------------------ ... if (ioctl (fd, TIOCGRS485, &rs485conf) < 0) { printf("Error: TIOCGRS485 ioctl not supported.\n"); } /* Enable RS-485 mode: */ rs485conf.flags |= SER_RS485_ENABLED; /* Set rts/txen delay before send, if needed: (in microseconds) */ rs485conf.delay_rts_before_send = 0; /* Set rts/txen delay after send, if needed: (in microseconds) */ rs485conf.delay_rts_after_send = 0; if (ioct…

Hi, I am using Nanopi Neo board and I need RS485 driver to control DE pin automatically. I have prepared DTS Overlay file: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&uart1>; __overlay__ { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&uart1_pins &uart1_de_pin>; rs485-rts-gpios = <&gpio6 8 0>; /* PG8 active-low */ linux,rs485-enabled-at-boot-time; rs485-rts-delay = <0 300>; }; }; fragment@1 { tar…

Hello, I am making a board coupled to a NanoPi Neo Core, and a RS485 converter to its UART2. The chip is a MAX1478 and I use the RTS (PA2). this is my armbianEnv verbosity=1 bootlogo=false disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=cpu-clock-1.2GHz-1.3v i2c0 i2c1 uart1 uart2 usbhost0 usbhost1 usbhost2 rootdev=UUID=a37457d6-57d2-4f17-a684-157b1a309a73 rootfstype=ext4 user_overlays=neo-core-stable-mac double-spi ds1307 param_uart2_rtscts=1 param_uart3_rtscts=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u if i run the command, cat /proc/tty/driver/serial |head -8 uart:16550A mmio:0x01C28800 irq:53 tx:120 rx:0 RTS|DT…

So I have an OPI0 perfectly running then suddenly it freezes. All I can find on /var/log/syslog Jul 1 10:35:10 localhost CRON[1553]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Jul 1 10:36:08 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:36:38 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:37:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:37:37 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:38:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:38:37 2018 [v8.16.0 try http://www.rsyslog.com/e/200…

Hello , How do I get RTC working on Banana Pro. I think I have 2 options 1. Built in one 2. External [DS3231] Here is some info about the setup i got. dmesg | grep -i rtc [ 1.928725] sunxi-rtc sunxi-rtc: Warning: RTC time is wrong! [ 1.934023] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 hwclock --test -D hwclock from util-linux 2.27.1 Using the /dev interface to the clock. Last drift adjustment done at 1506000286 seconds after 1969 Last calibration done at 1506000286 seconds after 1969 Hardware clock is on UTC time Assuming hardware clock is kept in UTC time. Waiting for clock tick... select() to /d…

Hi, After today upgrade (Kernel / Firmware) my DVB-T pen stop working with dump1090. Error message: /usr/bin/dump1090 --net --gain -10 --modeac --net-bo-port 30005 --net-bi-port 30104 Found 1 device(s): 0: Realtek, RTL2838UHIDIR, SN: 00000001 (currently selected) Kernel driver is active, or device is claimed by second instance of librtlsdr. In the first case, please either detach or blacklist the kernel module (dvb_usb_rtl28xxu), or enable automatic detaching at compile time. usb_claim_interface error -6 Error opening the RTLSDR device: Device or resource busy I tried to follow this tip: http://discussions.flightaware.com/ads-b-flight-tracking-f21/dump10…

I am running the newest version of armbian (5.30) on my Orange PI One, but I run into a strange issue. Whenever I connect an usb dongle (RTL8188EU), it is recognised and works, but two NICs are shown in the network manager. Also ifconfig shows interfaces, where the lsusb shows only one device. Also strange is that one is shown as wlan1, but the other as wlx<macaddress>. Does anyone know what might be causing this issue?

Flashed the latest Jammy 5.15.48 image and the device went offline After connecting to HDMI I found out that RTL8188EUS is no longer available. Previous Focal image worked fine in headless mode with a `0bda:8179` dongle. Anyone knows why the driver has been removed? Thanks

Hello, i have a problem whit usb wifi dongle rtl8192cu, from latest armbian desktop in network manager show the essid network but it's impossible connection! board: Orangepipc Spoiler [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.113-sun8i (root@devel) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #16 SMP PREEMPT Tue Jun 13 14:15:57 CEST 2017 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT a…

Orange pi pc plus. i have this crazy logs with latest buster regarding the RTL871X wifi chip, it consume up to 5 megs a day on each kern.log, messages and syslog. what can i do to turn this off? my opi's are in the wild and i do have to connect via cellular to check logs at time via vpn and it's not cool to transfer that much data. Thanks.messages

I'm getting logspam from RTL871X running buster on my OrangePi Plus 2e. I'm not using wifi on this so I guess I could just disable/blacklist rtl871x to stop this? But is there a better/cleaner way to stop all these log entries? Or does it indicate something is broken/mis-configured? syslog is showing many many log entries from RTL871X; each minute I get the following sequence: May 23 16:52:06 orangepiplus2e kernel: RTL871X: cfg80211_rtw_scan(wlan0) May 23 16:52:06 orangepiplus2e kernel: RTL871X: _rtw_pwr_wakeup call ips_leave.... May 23 16:52:06 orangepiplus2e kernel: RTL871X: ==>ips_leave cnts:112 May 23 16:52:06 orange…

Hi all, anyone had success with rtl8723bs sdio wifi + bt module? I'm figuring out how to make it work on a cubieboard2. Any suggestion would be much appreciated.

Hi, RTL811AU wifi dongle has different wlan number each time it is plugged in or system started. It has different MAC as well. Numbers after wlan corresponds to attached MAC addresses. my sysem is OrangepiPC with development kernel. dmesg shows following (I have removed a plugget in the same dongle 3 times)

Hi all, I need to enable rts/cts on my OrangePi Zero with Armbian buster with Linux 5.4.26-sunxi installed. I added the "param_uart2_rtscts=1" (I'm using /dev/ttyS2) to the /boot/armbianEnv.txt file On mi code I use this initialization of the port. xxxxx.c_cflag |= port_parity | port_bits | port_stop | CLOCAL | CRTSCTS | CREAD; Not only rts/cts but also the tx and rx pin aren't working now. Has anyone managed to enable the port on this board? Am I doing something wrong?

Hello is there any way to stream rtsp on H3 devices? With this i can record video ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 -b:v 64k -c:v cedrus264 test.mp4 My hardware is NanoPI neo air + CAM500B. Using friendlyARM's image at the moment because camera don't work on Armbian. (/dev/video0 is there but mjpg-streamer end with errors for example)

Hello everybody, I tried building an in-kernel module for USB Dongle Bus 001 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU] on my OrangePi Plus. Armbian supplied module from aircrack-ng/rtl8812au has become aging and raises exception errors on modprobe -r. It was deactivated : root@orangepiplus:/etc/modprobe.d# vi blacklist-88XXau.conf #blacklist 88XXau I made a fresh install of Armbian minimal image, then switched to : root@orangepiplus:~# uname -a Linux orangepiplus 6.15.4-edge-sunxi #1 SMP Fri Jun 27 10:13:43 UTC 2025 armv7l GNU/Linux root@orangepiplus:/usr/src# cat /proc/version Linux version 6.15.4-edge-sunxi (build@…

I use orange pi zero with armbian xenial 5.38 with update kernal via apt-get upgrade the issue is that sometime the device get hang at boot before the start of the kernal, and then we have to unplug it and plug it again i want to start watchdog at boot itselft, so if this happen the device reboot automatically i already sold 1000 devices, but now the sales stop due to this issue please help Thanks

Hello, I'm interested in how to run the application calculated for a normal computer x86_64 (ubuntu), since the architecture arm is not supported, you need to do it as a bypass, in the application I post the script that I need to install. This is a radio bot. help me please sinusbot_installer.sh

Hi everybody, I have an Orange Pi One run Armbian Server image. I want to write an GUI application by QT on the my computer and compile/run on Orange Pi One. I read and follow some tutorials, but not success. Are you suggestions for me? Many Thanks!

Hello Community! Does anybody tried to run the .Net Core or ASP NET Core runtime package on OrangePi PC2? I was trying to install it using MS guidelines [https://www.microsoft.com/net/download/linux-package-manager/ubuntu16-04/runtime-current] but no luck. I was searching Goolge for a while, and tried bunch of common solutions related to Linux and .Net Core installation - with no luck unfortunately. I am using: OrangePI PC2 ARMBIAN 5.59.180815 nightly Ubuntu 16.04.5 LTS 4.11.1-sun50iw2

Running apt-get dist-upgrade tries to install the new Allwinner H3 kernel but it takes the Orange Pi PC a really, really long time to extract and install it. The heartbeat LED flashed really fast and after 30 minutes I elected to stop it. Has anyone succeeded doing apt-get dist-upgrade today to get the new kernel on the Orange Pi PC or Orange Pi One, and, if so, how long did it take? The packages are: linux-firmware-image-sun8i linux-headers-sun8i linux-image-sun8i linux-jessie-root-orangepih3 linux-u-boot-orangepih3-default Thanks in advance for any information or advice.

i run a cubietruck on armbian with 4.6.2 kernel. it starts with the software on mmcblk0p1 (with kernel 4.6.2 and the /lib dir on the sd) but uses as root a partition of the ssd. when i upgrade now, i see that the upgrade process produces a new initrd.img-4.6.3 and removes the old 4.6.2. (diagnosis: the system runs, but the keyboard/mouse connected to the usb is not functional - desktop over net works!) i assume that there is something wrong with the boot.cmd - but i do not see exactly how to fix it. the upgrade process uses the ssd .../lib directory and removes 4.6.2 there. if i would mount the /boot directory with the running system (in fstab) - would this hel…

Hi I want to use my orange pi zero to stream music from my NAS and some internet radio stations. I want a good remote control from my phone so I want to use yatse to control Kodi. I installed xfce4 and vnc and I am able to connect to the desktop environment. I then installed kodi but it does not work: Xlib: extension "RANDR" missing on display ":10.0" I checked and randr is actually not missing, just not loaded. I tried to get it running for the past two hours but no luck. I am not very familiar with linux so I am stuck at this point. From what I read it must have something to do with the graphics adapter drivers. Any help would be ap…

Good day. I've purchased lcd 5'inch LCD. I have some troubles with HDMI connection (no image), but i fixed it using this topic: link. (drivers at disk doesnt take any effect) But i can not run touchpad. I used different hints but god no effect board - Orange Pi PC Plus kernel 3.4.113-sun8i module ads7846.ko at /lib/modules/3.4.113-sun8i/kernel/drivers/input/touchscreen My script bin: Spoiler [spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3&g…

Hi I have the following question which I have asked both to someone from Armworks and also #friendlyelec on free node. I haven't got the solution but it has lead me towards the answer. So my problem is in not being able to get xserver running that it indicates the driver "sun8i-de2" can not be found. As far as I can find not having the driver is the entire problem, however I can't find where I can get it. Below I have posted my full problem below: I have been having problems getting things to display on the LCD display using Xserver. I have been successful displaying images using fbi though. The board the we have it the NanoPi-Neo Plus2. Currently…

I have a orange pi pc (H3). I connected a thermal printer which has a TTL interface so I connected the TX wire from the printer to 8 and RX to 10 to orange pi. I change the serial port in my script to /dev/ttyS0 and tried a test print but it will not print. I have tried this in raspberry pi 2 and it works. Any tips how to connect the thermal printer to orange pi.

Hallo, i have an old istallation of armbian and it's working perfect , thank you Igor for your work..! i want to upgrade my stable debian wheezy without breaking nothing :p the current version of armbian is : Linux cubietruck 3.4.104-sunxi #1 SMP PREEMPT Fri Oct 17 16:13:30 CEST 2014 armv7l GNU/Linux and the : /etc/apt/sources.list deb http://ftp.it.debian.org/debian wheezy main contrib non-free deb-src http://ftp.it.debian.org/debian wheezy main contrib non-free deb http://ftp.debian.org/debian/ wheezy-updates main contrib non-free deb-src http://ftp.debian.org/debian/ wheezy-updates main contrib non-fre…

Hello, my Orange Pi Zero CPU is constantlyrunning at 67-68-70°C (it is the same with/without passive cooler). Is this temperature ok for my board? Can I run it with this temperature long time (weeks, months, years)? Thanks for help.

Hi, I tried to safe-upgrade (apt-get upgrade) Trusty today but got the following notice: Failed to fetch http://apt.armbian.com/dists/trusty/main/binary-armhf/Packages It would be OK to dist-upgrade to Xenial anyway as described in the Docs ... apt-get install update-manager-core do-release-upgrade -d # further to xenial apt-get dist-upgrade ... but I think it would be a good idea to start from a proper Trusty. Any suggestions. Thanks in advance Mark

Hi all I'm trying to set up a samba AD domain on a BananaPi M1+ running Armbian 5.31 (Debian Jessie) but fail miserably when trying to provision the domain. Using "samba-tool domain provision --use-rfc2307 --interactive", all starts well but then falls over with the error: Error loading module '/usr/lib/arm-linux-gnueabihf/samba/vfs/acl_xattr.so': /usr/lib/arm-linux-gnueabihf/samba/vfs/acl_xattr.so: cannot open shared object file: No such file or directory error probing vfs module 'acl_xattr': NT_STATUS_UNSUCCESSFUL and a whole lot more. Bottom line is that this "acl_xattr.so" doesn't exist anywhere on the m…

I have a fresh install of Armbian 5.14 on a orange pi one. I i have updated and upgraded it. I have only installed synaptic and nautilus. I then followed the instruction to install the micro home server and I commenced to install the Samba option. It ran and then once it had finished said something like samba not running or samba not configured. I tried to browse the network and look for my Tplink NAS router and it says "this location could not be displayed." I would appreciate any ideas to get samba running.

I have an odd problem with a Orange Pi Zero H2+ 512mb I have samba setup with share all correctly BUT my windows XP pc cant see the share name at all unless I search for the IP then under the IP I can setup share maps on my PC and all is good. However I have tried 4 different Windows 10 PCs now and they cannot see either the server name or even the IP to get the shares :-( even though I can ping the server (OP-zero) IP address and get a perfect response. I am tearing my hair out here I need this to work on Windows 10 for a small server project I am working on. Also the exact same PCs CAN see the Shares and server easy with the exact same setup with Ubuntu 16.…

I've got a new problem with my Olimex A20 Lime2 board. The board doesn't freeze anymore (http://forum.armbian.com/index.php/topic/295-freezing-problem-with-olimex-a20-lime-2/) but after a week I've got a very slow speed using samba: about 300 kbps. I've tried to restart the smbd service but it doesn't work. The smbd process don't use cpu: < 5 %. If I restart completely the board, samba start to works again very fast and use the cpu: > 50%. How can I discover where is the problem and how to fix it? I'm using Debian jessie 4.2.6-sunxi, and there are no more updates.

Updated this afternoon and noticed my SATA drive isn't connecting. > dmesg | grep SATA [ 3.633118] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 32 [ 3.952927] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.781288] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102706] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102730] ata1: limiting SATA link speed to 1.5 Gbps [ 15.422687] ata1: SATA link down (SStatus 0 SControl 310) Let me know what I can do. Thanks!

Today I updated my BananaPI M1 board, replaced the Bananian OS with Armbian Armbian_20.05.4_Bananapi_focal_current_5.4.45.img. I'm not getting the SATA with connected 1TB WD10JFCX working. The HD worked before with the Bananien kernel 3.4.x What can I do, how can I test, how can i get more information about the reason? The board is powered via the Micro USB and armbianmonitor reports DC-IN voltage > 5V

Hi, Does armbiam fully support SATA port on Olimex Lime2? greetings, Marcin