Allwinner sunxi

I have Orange Pi Lite. I installed Ubuntu Xenial Nightly 4.10.1. Orange Pi Lite has WiFi. I would like to run hostapd. I want to see the Supported interface modes. I run the iw list command, but it does not return anything. What is the problem? I was looking for an answer on the forum, but I did not find it. Driver = rtl8189fs

Hallo All, I installed Armbian bpi m2p. With both server and desktop after i change, off course. i getting stuck with apt-get update not working. error showing are "could not resolve faild to fetch. Anyone know how to solve this? Also there seems a problem with the ethernet adapter. When i want to add new connection, after selected new connection, i cannot chose in dialog menu, nothing can be changed or edit. with warm regards, Frank

Hi, just a quick sanity check - is install to eMMC on pinebook known to be working (with recent Armbian images from the wip section), and is nand-sata-install the right way to do it? It just occurred to me that I might be spinning my wheels trying to figure out something that just isn't ready yet Thanks, James

Hello, I know there is documentation about it, but I think I've tried everything and my orange pi is still not displaying on my hdmi screen. The green LED is active, and the red one is blinking. I've written a Raspian image to the sd card, corresponding with the board. I have read about bin2fex but I can't have access to my sd card data on my Windows, to execute bin2fex. Thank you for your help !

Hi, I'm looking for a working OS Image for Nano Pi Neo Air for using I2S, SPI and Bluetooth (AP6212). Is there a release I can use "out of the box" for this? Regards Bernhard

I have ironed out my OPZ woes and have it working well now along with the Mainline Armbian image. As we may know the onboard wifi is garbage and will not get fixed, however I found a dirt cheap plug and play usb alternative on ebay (or aliexpress.com) using the common (Ralink?) mt7601u kernel driver. As long the dongle matches the photo in the listing it should have the same chipset. It has very low power consumption and at least with my wifi router gets the maximum 10mbit/sec throughput for downloads on my internet connection at a distance of 5 meters. I also added to /etc/modprobe.d/blacklist.conf .... blacklist xradio_wlan …

BACKGROUND: Back on June 27th, I posted my questions regarding my wish to have certain kernel features activated (or not) by default in the Armbian/Debian kernels of the time -- specifically since I wanted to activate 'PPS' features in order to build a Stratum 1 GPS/PPS timeserver: Kernel Option Requests? Here are the 'old' instructions that I used back in June: ORANGE PI PLUS H3 with GPS/PPS I ended up needing to install VirtualBox with an Ubuntu 16.04 environment, and successfully created what I needed (i.e. 3.4.113-PPS-sun8i). I was also eager to create a much newer kernel, but that failed (i.e. 4.11.5). My Orange Pi PC…

Fresh installation of Armbian On OrangePie+ 2e Not Shutting Down Network lights still on ..... BT still On but not SSH connectivity neither image on monitor any ideas ? Thanks

Hi all, I have Lime2/legacy kernel 3.4, within 2-3 min after boot the network connection are dropped and up again. The problem for my automation, I can fix it? Regards,

I bought an OPi Zero, the extension board, a 1/8-to-rca audio/video cable to plug into the AV jack of the extension board, and a 16 GB SDHC card. Loaded Armbian Stretch onto it, plugged in ethernet without any of the AV stuff just to start. The Pi doesn't even show up on my router settings so I cannot access it via Putty or any other SSH program. I turn it off, attach the extension board and av cable, and plug it into the TV in the hopes that I can start working on something with a USB keyboard...nothing shows up on the TV. I'm hoping that's a software issue and not an issue with the actual extension board I bought. I know for a fact it's loading Armbian because I can act…

Hi, I'm a new user to SBC and is thinking of buy an orange pi pc 2. Since it has a Mali450 GPU and the manufacturer claims that this SBC support OpenGL, can I use that to play some open source games like 0.A.D on armbian? Is armbian have mali gpu drivers installed? Thanks.

update: the 5.59.180828 nightly building version may display a error temperature degree。 test real temperature using a thermometer ，two version display the same degree in thermometer about 49degree idle。 1. same board:orange pi zero plus v1.1,same room temp. 2. armbian 5.59.180828 nightly , idle cpu temp. about:49 degree. ------------------------------------------------------------------------------------------------------------- Welcome to ARMBIAN 5.59.180828 nightly Debian GNU/Linux 9 (stretch) 4.14.67-sunxi64 Linux opizeroh5 4.14.67-sunxi64 #85 SMP Tue Aug 28 10:55:16 CEST 2018 aarch64 GNU/Linux Stop monitoring using [ctr…

I have a headless Orange pi 3 and wanted to be able to test a new install. Is it possible to issue a specific reboot command that will switch to boot from one storage to the other storage? I have armbian bionic installed and running on the EMMC. and A new bionic build installed on a new SD card. So, if i'm tinkering with the new build on the SD card, can i reboot to the EMMC without removing the SD card, and then similarly reboot from the EMMC into the SD card build??

Hi, we experience change in owner:group in /var/log. Eg. mosquitto folder requires mosquitto:mosquitto and is changed to root:root. After this change mosquitto service is down. Any pointers are very much appreciated. Many thanks. Rostislav

Hello everyone, Apologies if this is not the right forum for this questions, but could not find any more appropriate one after some searching. I get an HTTP 404 when I try to access the pre-built images for the nanopi m1 plus from the board page. I know the board is EOS but for other EOS boards I can still download the images. Is there any reason why this board seems to have disappeared completely ?

Hi All, I'm trying to enable SPI2 on a A20 Olinuxino LIME board. I found an old post on this forum regarding LIME2, so I try the same and in armbianEnv.txt I add the lines: overlays=spi2 spi-spidev param_spidev_spi_bus=2 param_spi2_bus_pins=b At reboot, the message: Failed to load '/boot/dtb/overlay/sun7i-a20-spi2.dtbo' I think because the file is not found Only SPI0 is active How can I enable SPI2 ? Thanks in advance PaoloC

Attempting to connect ILI9341 LCD with XPT2046 Touch to NanoPi NEO Core2 and then migrate to NanoPi Duo2. The ILI9341 / XPT2046 peripheral board has shared SPI with a separate slave chip select for the screen and touch controllers. Starting with hardware datasheet for the H3 I see there is lots of support for different chip select implementations. This makes me think I am on good footing from a hardware perspective. What is not clear to me is how the register support for four slave chip selects translates into pin assignments. Reading through spi-sun6i.c., for example, static int sun6i_spi_transfer_one( ... ) uses SUN6I_TFR_CTL_CS_MANUA…

Just flashed Armbian 20.11.9 for NanoPi Neo 2 with kernel 5.10.4. I have run armbian-config to install kernel 5.10.4 source, but there is no any option for 5.10.x kernel sources, I see only options for 5.8.x and 5.9.x.

/proc/cpuinfo does not list serial number How do I read the chip serial number?

At Raspberry Pi (at least on R.Pi 4) it is possibility to set up more than one 1-wire bus. Can that be done on Orange Pi plus 2e with Armbian? uname -a Linux XXXXXXXXXXX 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l armv7l armv7l GNU/Linux /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=d908a8da-8d2e-4802-8a05-aaab4f3290bb rootfstype=ext4 overlays=w1-gpio param_w1_pin=PD14 param_w1_pin_int_pullup=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u If it is possible: Any tip on configuration will make me happy. And can it be internal pu…

Good day everyone, I am running into some issue while trying to update packages on my Nano Pi Neo Plus 2, I am currently running Armbian 23.02.2 Buster with Linux 5.15.93-sunxi64 on the board. I am trying to update my packages with apt-update however the error I am receiving back is the following: E: The repository 'http://mirrors.dotsrc.org/armbian-apt buster Release' no longer has a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details. Can someone help me out to fix it? Thanks in advance!

Nanopi neo air stucks on "Starting kernel..." after some random power losses (2-50) during loading I think it's because of corruption of armbianEnv.txt. Normal UART logs: UART Logs with stucking on "Starting kernel" U-Boot SPL 2024.01_armbian-202ns16550_serial serial@1c28000: p024.01-S866c-P7738-Hadc5-Vefe9-B2eb2-R448a (Feb 06 2026 - 03:49:45 +0000) Allwinner Technology 0) Model: FriendlyARM NanoPi NEent from FAT... Unable to use mmc 1:1... ial Err: serial Net: No ethernet found. starting USB... No working controllers found 1(part 0) is current device Scacr 5475 bytes read in 2 ms (2.6 MiB/s) ## Executing script at 43100000 U-boot loaded from eMMC or s…

Hi, I'm using the Igor-Image: Linux cubieboard2 4.0.5-cubietruck #12 SMP Thu Jun 11 19:18:02 CEST 2015 armv7l GNU/Linux I installed a program that is using a PID-file, normally under: /var/run/fhem/fhem.pid I created a sub-folder and changed the owner and permissions. With the next reboot, all changes where lost. I noticed that the /var/run is linked to /run and this is a tmpfs. So, is there an option to add a subdirectory permanently to /run? Alternatively I will add a short script, that will do these operations after reboot, but in my opinion, that is not the fancy way... greets brenndorfler

hello I am new to the forum My problem: how to change the screen resolution when I'm on the output vga? the only proposed resolution is 1920X1080 board : cubietruck linux : Armbian_4.5_Cubietruck_Debian_jessie_3.4.109-legacy screen : VGA output, 1280X1024 Desktop environment : XFCE 4.10 Thanks for your help

I'm trying to test I2S Audio playback. I've mounted a Windows network share like so: //apps/MUSIC /mnt/music cifs noserverino,iocharset=utf8,username=media,password= 0 0 And playing with: aplay -D default:CARD=sunxisndi2s /mnt/music/test.wav With this result: underrun!!! (at least 2.218 ms long) Any ideas?

Hello, I'm testing the latest (kernel 4.5) jessie server vanilla on a Olimex Lime2. If a battery is connected to the board and the power plugged in, the board start by itself ! I would like to change this behavior, is there any file to tweak ? Thanks

Hello, I have a custom board with A20 and I like to share the UART7(I20/I21) pins. I mean sometimes used as UART and other times used as output ports. Should I always change the FEX file to use one u other functionality. The perfect way is using both option without restart the system. Thanks!

I see in the lib/extras-buildpkgs there's fswebcam-gc2035 config but I see no way how to build the kernel with support for gc2035 ? I built "Linux orangepione 4.10.11-sun8i #2 SMP Tue Apr 18 17:55:20 CEST 2017 armv7l GNU/Linux" but it does not recognise gc2035 and there's no gc2035 module anywhere to be found I have ./kernel/drivers/usb/gadget/legacy/g_webcam.ko ./kernel/drivers/media/usb/stkwebcam/stkwebcam.ko but nothing wrt gc2035 I also found https://github.com/avafinger/gc2035.git that's supposedly "better driver" for gc2035, but it's for 3.x kernel, don't see a way to get it into 4.10.11 kernel an…

Hi friends, I am trying to downclock my OPi Zero and set/disable unused cores 1,2,3, limit DRAM speed, limit max cpu core frequency, put voltage down. Is this possible on Opi Zero? I tried e.g. but when I cat /sys/devices/system/cpu/cpu3/online is is always 1. Any idea please? Some advice how to do all of this is highly appreciated. I am trying to downclock Opi Zero to push produced heat down.

I am using GPIO(CON3) pins 8 and 10 for a project. In BPI M1+, functions for those pins are PH0 and PH1 respectively. https://bananapi.gitbooks.io/bpi-m1-bpi-m1-plus-/content/en/bpi-m1+_gpio_pin_define.html But, when I added overlays=uart3 ,I didn't work properly . When I checked the overlay file sun7i-a20-uart3.dtbo , by changing it to .dts , I figured out that this overlay file uses PG6,PG7 pins, not PH0,PH1 pins. So, to modify the configurations without adding uart3 overlay in the /boot/armbianEnv.txt file, I wanted to edit the /boot/dtb/sun7i-a20-bananapi-m1-plus.dtb file. When I check the file, there are uart3_pins_a option and uart3_pins …

Hello, I'm trying to make MB1242 sonar working with my nanopi but every time I run i2cdetect, I got "i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0". Sonar works fine on RPI after changing i2c_baudrate to 50000. Is there any way to do the same at nanopi?

Hello, recently i bought Orange Pi Win Plus board and have installed Armbian (Ubuntu xenial server) on it. With stock kernel linux-image-dev-sun50iw1, linux-headers-dev-sun50iw1 and linux-dtb-dev-sun50iw1 all hardware working ok except USB DVB tuner myGica T230, needed for me, which has not enabled in kernel configuration. I found linux-image-dev-sun50iw1 (https://www.armbian.com/kernel/, section Allwinner A64), its sources and etc has been removed from Armbian repository. This is question N1: maybe someone has sources for this kernel for build? Today i'm trying to build 'next' and 'dev' kernels for this hardware in Ubuntu 16.04 VM 'DEV'…

Things downloaded last week, When switching to alternative kernel is executed in Armbian Config, the screen set to 1280 x 1024 has been changed to 1280 x 720 and it was not able to be rewritten, so do not run the Switch to Alternative kernel and keep the 1280 x 1024 screen It is GQRX-SDR, since error-6 (even if blacklist maintenance is done) comes out, As a workaround, I ran Switch to the alternative kernel and avoided error-6. (I give up on screen 1280 x 720) But today, when downloading and installing the same software, the screen shows 1280 x 1024 It was able to be maintained. Sorry to make software, it is truly a hard work. But the object of today (201…

No sound via the hdmi port to hdmi tv port however I can use headphones with the 3.5 mm audio jack and it works fine. Not sure if my board is broken either. I just got it. The only image that works with my orange pi pc plus is Armbian Stretch edition. The ones I have tried thus far are armbian xenial multimedia edition, retrorangepi, android 7 from orangepi website they all don't work haven't tried bionic armbian edition though. But that is for another post just thought to mention that. 1. Logs when you can boot the board: armbianmonitor -u https://pastebin.com/e5xb2gZD

Hello everybody! There was a problem, my OrangePI R1 with the Armbian Stretch OS running works in the access point + bridge mode (hostapd & bridge-utils), and when the client downloads a large file from the network, the RTWHALXT process loads the CPU by 100% and rtw_xmit_thread by 20% (watched using top) as a result, the processor freezes. How to fix it? Thanks in advance, sorry for my English I am from Uzbekistan.

I have orange pi one with Armbian Xenial desktop legacy kernel 3.4.y which have a script.bin file in /boot directory and doesn't have /boot/dtb directory ...but when i installed Armbian Bionic mainline based kernel 4.19.y, I found the .dtb files but not the script.bin ....now i don't know how to configure both touch screen and the pwm pin! is the .dtb file (sun8i-h3-orangepi-one.dtb) is the same as script.bin or orangepione.bin ? if so, how to configure it? because i am used to convert the script.bin to .fex to configure it and then back to .bin.

Hi guys orangepi-one and i'm trying to install the Super Nintendo Classic Controller wich is i2c bus /---------\ | | | 1-2-3 | | 4-5-6 | | _____ | \_/ \_/ ``` | Controller Pin | Function | Pi Pin | |---------------:|---------------|-----------| | 1 | I2C data | 3 (SDA) | | 2 | device detect | - | | 3 | +3.3V | 1 (+3.3V) | | 4 | GND | 6 (GND) | | 5 | not connected | - | | 6 | I2C clock | 5 (SCL) | i have wired the controller to the orangepi bus port 0 and port 2 i found a driver fo…

Hi, I am looking to Secure Boot Allwinner H3. We use Nano Pi Duo2 with latest Armbian OS. End goal is to have all the OS / Data on the SD Card Encrypted. Can anybody help ?

I configured Armbian on a mSD card and decided to try and move it to the eMMC. I used the nand-sata-install utility, All files from the mSD card are copied, and the last step fails. I get Error: no u-boot package found, exiting Any pointers?

Hi, I am having a problem getting the graphical login to work... What I run is an ubuntu jammy image with gnome, however when I boot with my tv connected via hdmi it seems to work at first but finally I end up with a screen just displaying the above error. armbianEnv.txt contains the line "disp_mode=1920x1080p60" (a mode my TV supports), yet when the device starts it uses the 4k mode - could this be part of the problem? So how could I get this working and how would I ensure that my device only uses fhd resolution, even though my tv can also do 4k? Many thanks!

Hello, I encounter a strange behaviour with Lime2. When on battery and AC plug-in if I ask for a shutdown -h now, the board reboot by itself and the system does not stop. When on battery only, the board stop with the command shutdown -h now I read about those 2 variables CONFIG_MFD_AXP20X=y CONFIG_REGULATOR_AXP20X=y to set in u-boot/configs/A20-OLinuXino-Lime2_defconfig But after building the a u-boot package with compil.sh this setting does not have any effect... zgrep MFD /proc/config.gz command does not show the CONFIG_MFD_AXP20X=y variable Did I miss something, any ideas ? Thanks Florian

Hi everybody! We have an application that uses RS-485 and we decided to use the OMAP UART implementation, but it doesn't seems to work with Cubieboard A10. We tried to enable in userspace, by calling ioctl and also via dts file. ioctl (C code): ------------------------ ... if (ioctl (fd, TIOCGRS485, &rs485conf) < 0) { printf("Error: TIOCGRS485 ioctl not supported.\n"); } /* Enable RS-485 mode: */ rs485conf.flags |= SER_RS485_ENABLED; /* Set rts/txen delay before send, if needed: (in microseconds) */ rs485conf.delay_rts_before_send = 0; /* Set rts/txen delay after send, if needed: (in microseconds) */ rs485conf.delay_rts_after_send = 0; if (ioct…

opi pc arm 5.10 ALSA no output from speakers but output only available through hdmi. when installed pulse audio able get and change audio hdmi to analog but when switched to HDMI playback hangs and freezes. Any solution?

Hi there, As the topic title says,... Is there any available option to install/setup Domoticz server onto Orange Pi Box using Armbian Desktop or Server version? Thank you! Kind regards

Hi! I look for this topic in every place at the internet but all of the topics are not related with my problem. I have a custom board based on the Lime2-emmc. It can boot from SD, but when I tried to copy the same u-boot-sunxi-with-spl.bin to the emmc and try to boot, nothing happends, the screen is empty. dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk1 bs=1024 seek=8 boot from SD http://imgur.com/a/OHxzm When it boots from SD the u-boot shows both (SD on MMC0 and EMMC on MMC1) I´m using the A20-OLinuXino-Lime2-eMMC_defconfig with some mods to my board. My emmc is unit is KLM8G1GEME-B041 and is connected to the board like the emmc unit is connected…

I did manage to use the rmbian_5.27_Orangepizeroplus2-h5_Debian_jessie_dev_4.11.0.img.xz image and things boot fine. I also get pretty console on hdmi. But no network, and I don't have a way to get the keyboard on. Any suggestions on what kind of an adapter I need to get power AND usb keyboard to the thing (since there are no extra ports on it)? Or is it serial? Good recommendation on proper 'converter". I did modify the initial armbian_first_boot to enable wifi with proper ssid / password, and even enabled static, but no dice. Thomas

Hello, i have this strange problem after upgrade to kernel 3.4.113-sun8i (orange pi plus 2e, debian server version armbian, Seagate BarraCuda 2TB sata hdd, connect with axagon usb3 to sata adapter and set standby after 30min, power by power adapter). Before update, all working fine. Now, after kernel update, drive never stop spinning. I stopped rpimonitor and smartd services and still dont work. If I use hdparm -Y /dev/disk/by-uuid/... then drive spindown but after som second start spinning again. How can i solve this? this is my syslog Oct 5 11:36:21 localhost kernel: [ 1450.160126] usb 4-1: reset high-speed USB device number 3 using sunxi-ehci Oct …

I recently received my kit, which consists of the Neo, heatsink, and acrylic shell. Installed Debian_jessie_default.7z with Etcher onto a Kingston SDCIT/8GBSP. PCB 1.3+ uses a more sophisticated voltage regulator than earlier revisions... The temperature is excellent so far (only 40c). I can run some more tests if someone provides instructions. So these boards do not in fact require a heavy copper plane for heat dissipation. I did use a superior heat pad rather than the one that is provided with the heatsink kit. Ideally, you would want something like a 4mm or so copper shim with good quality thermal paste applied to bo…

Hi, I have 3 Orange Pi Zero running with the same sd image. It's all working fine, but yesterday I added a fourth device, which for some reason took a MAC address that is the same of another device, causing issues on the connection for both of them. I'm using the mainline kernel ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi. Searching on the internet, I found someone saying that mac addresses for Orange Pis are randomly generated every time the device reboots, but in my case the taken MAC address is always the same for every device. I saw to that people suggested to check the content of the /etc/modprobe.d/8189fs.conf f…

Armbian Bionic not sound output 3.5mm jack root@orangepipcplus:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0

Need to know if there is any real time operating system for nanopi M1 plus.

I'm trying to send a music from my NAS on the base of Cuibetruck (Allwinner Tech SOC A20 ARM Cortex-A7 Dual-Core T) Ubuntu Xenial with Armbian Linux 3.4.113-sun7i with bluealsa to my bluetoothreceiver connected to speakers. My working configs are in my answer to the question: https://askubuntu.com/questions/1197072/sending-audio-to-bluetooth-speaker-with-bluealsa Anyway when I play mp3 with mpd or wav with aplay the music is extremely stuttering. Question on bluealsa Github (https://github.com/Arkq/bluez-alsa/issues/279) ended with advice to check UART set up (which is already too complicated for me). My question is anybody managed to setup a nice and smooth audio ou…

Hi - I have been using Armbian buster stable on Orange Pi Zero for the past 12 months, starting with 5.92 last August and going up to 20.05.7 today. In all of these versions, clock speeds above 1.008GHz are unavailable, despite the board supporting 1.104GHz, 1.2GHz, 1.296GHz and 1.368GHz. They are not listed in armbian-config, cpufreq-set is unable to set them, and dmesg includes lines like: [ 10.030991] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV: 1320000, not supported by regulator [ 10.031017] cpu cpu0: _opp_add: OPP not supported by regulators (1104000000) [ 10.031305] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV:…

After about 10-20 hours of normal work the IP address on USB wifi adapter disappears. Ethernet adapter connected to the same router works well at the same time. System diagnosis information is collected when IP address is missing. After re-plug USB-adapter into the same USB port or reboot, the IP address appears back. Board: Orange PI PC, WIFI: EDUP dual-band on 8811CU chip, built-in drivers Image: 20.11.3 focal Router: Keenetic Ultra Previously I used built-in wifi of Orange PI+ and I didn't have similar problem. Is the problem specific to the WIFI adapter?

Hello, Is there anyone that has problem with USB keyboard on armbian 20.11.9 buster. I have tried both 20.11.6 and 20.11.9 buster nut the keyboard can't be recognized in armbian. (caplock, numlock LED don't work as well) I tried 4 USB ports on the port but doesn't work. The keyboard is working fine with my Windows PC. Thanks

I've been using the Armbian R1 image (Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.7z) on the NanoPi R1S with good success. In particular, the USB host port worked perfectly, with no changes required. I thought it was probably about time to upgrade to a newer kernel, so I downloaded Armbian_21.02.1_Nanopi-r1_focal_current_5.10.12.img, flashed it to an SD card, and booted. However, plugging in an external USB device results in absolutely zero shoing up in `dmesg -w`. I tried a USB-UART (STM32-based ACM), USB3 hub, USB 3 Mass Storage (Kingston 16GB), and a Playstation 3 Eye, without any entries in dmesg. To do some debugging, I also downloaded Arm…

Hi folks! So first here is the key question: Did anyone get exactly this combination NanoPi Duo2, ov5640 camera, armbian focal running? If YES, HOW … ? 😊 Details below. btw. buster would be also fine... uname -a output is Linux nanopiduo2 5.10.34-sunxi #21.05.1 SMP Thu May 6 20:13:21 UTC 2021 armv7l armv7l armv7l GNU/Linux I’m quite new to Linux and Armbian and have a slight problem using an Nanopi Duo2 and an ov5640 camera. It works pretty well using the image from FriendlyElec. This has been tested using the mjpg-streamer. Due to this success I’m sure the entire hardware setup is correct. Unfortunat…

I use Orange Pi PC+ with installed Armbian 21.08.3 on eMMC. On system i can't access to mmcblk0 device. In dev directory exist only mmcblk2* files related to eMMC. How can I enable access to the SD card ?

Hi, is this the right place to ask about support to configure a dtb overlay? I created a .dts file for my ILI9341 TFT display which is connected to a cubietruck running armbian. most of it I copied from the internet and adapted my changed (pin configuration and spi device). Previously I my configuration was done in a fex file and also created a pcb to connect the display to the cubietruck. See german documentation https://klautesblog.blogspot.com/2015/12/ili9341-22-tft-display-am-cubietruck.html?m=1 It worked perfectly but now I’m facing some issues with the new system. Armbian: Armbian 21.08.1 Focal Kernel …

Hi! I am experiencing problems with sd image install into NAND. Steps to reproduce: -Start with fresh cubie2 board (single a20 processor, image on this page: http://cubieboard.org/2013/06/19/cubieboard2-is-here/ ) -Image from link ( http://www.igorpecovnik.com/2013/12/24/cubietruck-debian-wheezy-sd-card-image/ ) -Selected "Cubieboard 2" / "Debian wheezy" / "24.8.2015, 3.4.108", image: ( http://mirror.igorpecovnik.com/Armbian_4.2_Cubieboard2_Debian_wheezy_3.4.108.zip ) -In the end, its a file "Armbian_4.2_Cubieboard2_Debian_wheezy_3.4.108.raw" -Use win32diskimager, write it to sd card, then boot from -First time root password is "1234" it will ask for a change, do …

Hi Back in February '15 I have started to write an instruction about the setup of a BPi-R1 (Router). In the threads of the Forum, the information is scattered and it takes so much time for each to get along. So I thought such a document would help to become not only faster, but to achieve a better result as well, as you can faster spend time with the device and tweak it. My know how is getting better, but things are still missing. If you like to help the 'community' with your know how, please leave comments in the document if you find errors or you find something missing. Google Docs Thank you in advance - for your support Cheers Tido

I purchased a usb wifi adapter RTL8192EU chip, 300Mbps. Requires Driver Installation (CD was provided with the adapter), When I tried to install driver on Orange Pi PC / Armbian, gave error. Need help. This is what happened: 1) Copied following 2 files from CD to Orange Pi PC by SFTP: rtl8192EU_linux_v4.2.2_7585.20130524.tar.gz install.sh 2) Run the installation script $ sudo chmod +x install.sh $ sudo ./install.sh 3) Output generated: Decompress the driver source tar ball: rtl8192EU_linux_v4.2.2_7585.20130524.tar.gz rtl8192EU_linux_v4.2.2_7585.20130524/ rtl8192EU_linux_v4.2.2_7585.20130524/clean rtl8192EU_linux_v4.2.2_7585.…

Hi guys, i've the following problem in my attempt to customize/study armbian: - succesfully compiled Armbian_5.17_Bananapim2_Debian_jessie_4.8.0 on Ubuntu 16.04 with default config; - burned image on SD card, (on the same card burned with Armbian_5.14_Bananapim2_Debian_jessie_4.6.2_desktop and the system boot is ok) - the board enter in this reset loop: U-Boot 2016.07-armbian (Sep 11 2016 - 10:06:05 +0200) Allwinner Technology CPU: Allwinner A31s (SUN6I) Model: Sinovoip BPI-M2 DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment HDMI connected: Setting up a 1680x1050 dvi console (overscan 0x0) In: serial Out: vga Err: vga…

hi, since 2 days i am using on my Banana Pi the Debian Jessie with 4.8.15 Kernel with installed Openmediavault 3. The system is working stable, but the network-performance is less then my older Installation based on Debian Wheezy with Openmediavault 2. I tried change the MTU-Size to 9000 and overcklocking up to 1.2 GHz, booth is not possible. I don´t know why ? For the setting the MTU-Size i edited /etc/network/interfaces and added the value "mtu 9000" -> no effects I tried set the MTU over the OMV WebGUI under network settings -> no effects. ifconfig shows me MTU=1500 Booth ways was at Debian Wheezy possible. At Debian Wheezy i had overclock the …

Hello. I have an Orange Pi PC+. I've just dd-ed Armbian 5.30 to an SD card and booted it up. Whenever i try to set the resolution to anything aside from the default 1280x720, then i only get a black screen. (I did not tried all possibilites.) How can i set my resolution to 800x480? It's connected via HDMI to a small LCD screen panel with this board. The output of h3disp: Usage: h3disp [-h/-H] -m [video mode] [-d] [-c [0-2]] ############################################################################ This is a tool to set the display resolution of your Orange Pi by patching script.bin. In case you use an HDMI-to-DVI converter p…

Hello! It's about installing Armbian on OPi+ 2E without a reliable sdcard and with no proper card reader - U-Boot goes to sdcard, Armbian image goes to USB dong then installed to eMMC. I did this once but can't remember what device was the sdcard in Android, if anybody knows it would be great to share. It mounts as /dev/block/vold/179:1, but writing (dd) u-boot.bin to 179:0 or 179 doesn't result in a bootable sdcard (the OPi boots from eMMC, and as far as I remember if it has bootable sdcard inserted it should boot from it no matter what is on the eMMC). There was also an issue with the nand-sata-install - I had to remove some lines as it wouldn't allow writing …

I download the image of this page, unzip the image and use rufus to burn it in a Samsung SD 32 GB evo. I use power supply of 3000 mah https://www.armbian.com/orange-pi-zero-2-h5/ It always fails, and it starts a reboot and kernel panic cycle What image i need use?

Hi, I'm trying to build wiring on my OPIZ here is the PI: Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi System load: 0.41 0.25 0.10 Up time: 1 min Memory usage: 9 % of 493MB IP: 192.168.1.18 CPU temp: 35°C Usage of /: 8% of 15G here is the log GPIO Utility [Link] /usr/bin/ld: gpio.o: relocation R_ARM_THM_MOVW_ABS_NC against `a local symbol' can not be used when making a shared object; recompile with -fPIC gpio.o: error adding symbols: Bad value collect2: error: ld returned 1 exit status Makefile:48: recipe for target 'gpio' failed make: *** [gpi…

Hi there, tomorrow I should obtain my OPi Zero Plus2. I see it does not have USB port (just GPIO for USB, so I could solder USB port for it with GPIO, no problem). Then, I will need to install my own raspbian.img on eMMC (I am using read only system). Till now I installed it on many SD cards to another Opi Zero's and used it so (because of lack eMMC). But how to install it on Opi Zero Plus2? Do I need to install it on SD card first and then go with nand-sata-install? Honestly, I would like to install it (the best) with USB or some other way, because I will need to install dozen of pieces and it is pretty time consuming to install if from SD ca…

Hy Just installed the Armbian Bionic image. Tried to attach different usb devices but they did not got registered. So I tried to look at the settings under Hardware in den armbian-config but it's gone.... I remember in the Armbian Stretch build it was Variable... Can someone help me Andy

Hello there I am looking to prepare kernel headers on orange pi plus to install mali drivers kernel version 4.14.68-sunxi Release Bionic Command : cd /usr/src/linux-headers-4.14.68-sunxi && sudo make scripts -j4 Result: scripts/Makefile.build:155: recipe for target 'scripts/mod/devicetable-offsets.s' failed make[2]: *** [scripts/mod/devicetable-offsets.s] Error 1 scripts/Makefile.build:587: recipe for target 'scripts/mod' failed make[1]: *** [scripts/mod] Error 2 Makefile:569: recipe for target 'scripts' failed make: *** [scripts] Error 2 I have tried everything here is the det…

On the download page images have kernel 4.18-rc7 I need headers for this kernel. How to find which commit is these images are built from?

Hi all. I've been working with the OPi3 and PineH64 model B the last days to try installing MESA and DRM drivers to make Panfrost work. This doesn't seem to work. Every time I install Mesa and reboot. It boots into the desktop normally, but a few seconds later the screen goes into one color. Everything is unresponsive. Can't go to a terminal window. Numlock is stuck... Just tried again with compositor disabled. It does take a bit longer before it blocks. But it still happens about a minute in every time. I can't find a ttl adapter for better debugging. I'll order new ones. Both the OPi3 (bionic 5.4) and PineH64(bionic 5.3) have the same issue. I'm using self …

Hi, I am trying to boot image Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.img, without success ... First, i am using following line to create SD ... ansible@solo:/mnt/backup$ sudo dd if=./Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.img of=/dev/mmcblk0 bs=1M status=progress ;sudo sync After connected my tty on internal pins on PCB, it is possible to connect to this tty and look at the first u-boot log ... Welcome to minicom 2.7.1 OPTIONS: I18n Compiled on May 6 2018, 08:02:47. Port /dev/tty-target-srv-nanopir1-170-position-1.2.4.1, 20:34:41 Press CTRL-A Z for help on special keys U-Boot SPL 2019.10-armbian (Feb 17 2020 - 06:18:08 +0100) …

hello everyone, I managed to make a WaveShare's 3.5" SPI LCD (actually designed for arduino) work on NanoPi Neo Core running on armbian Bionic 4.19.57, but now i"m having some issues with the touchpanel (using the same SPI). i'm trying to figure out how where to connect the touchpanel cs pin, which from what i have read suppose to connect to CE1. could someone help me find out which pin is it? maybe this will help: root@nanopineo:~# dmesg | grep "spi0.1" [ 8.334791] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.335492] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.348670] ads7846_device: spidev spi0.1 1000…

Before this I used to connect my APM 2.8.4 Flight controller to a Raspberry PI on Ground, Pin 8 and Pin 10. Today I tried to connect it to my orange pi zero plus2 H3. Pin 9, Pin 8 and Pin 10. On armbian-config toggle UART2. When i tried to connect to it using cat /dev/ttyS2 nothing came out. Once a while sent out some gibberish. I set the correct buadrate at 57600 and 91600 to no available. But I know the settings are correct because when I connect using USB through /dev/ttyACM0 it works. I tried ttyS1 and ttyS3 nothing came out of it. On Raspberry I had done this many times just by turning on the Serial Connection using …

Hi All I am not able to run Armbian Buster from the Downloads page (https://www.armbian.com/cubietruck/) on the CT board. Other images run fine, including: - Armbian_5.65_Cubietruck_Debian_stretch_next_4.14.78 (from archive) - Armbian_5.65_Cubietruck_Ubuntu_bionic_next_4.14.78 (from archive) - openwrt-19.07.7-sunxi-cortexa7-sun7i-a20-cubietruck-squashfs-sdcard.img.gz (from OpenWrt downloads site) The problem is that it endlessly reboots after resetting the CPU. The output from the serial port is shown below. I can interrupt the Autoboot and get to the Uboot console ok. The output from printenv is also shown below. Any…

This is a simple one, but the most annoying. The only Linux distribution I can not get to work in the Armbian on the Banana Pro. Sandisk 32Gb Class 10 MicroSD card. A USB power supply that does supply sufficient power and current. I write the image to the MicroSD card, insert it into the Banana Pro's card holder, power it up, the red LED lights up and ................. that's where it stops. No heartbeat on the green LED. The one thing I notice is that the image I download has only got one partition on it and that's the ext4 partition. It does not have the small FAT formatted partition and I think this is where it all goes wrong. …

Hello. I need to set a low level on a gpio pin PA6 on boot. I'm trying to do this through the device tree: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&pio>; __overlay__ { pinctrl-0 = <&pull_pins>; pull_pins:pull_pins { pins = "PA6"; function = "gpio_out"; bias-disable; output-low; }; }; }; }; I need to set PA6 to low. After boot, I see my overlay in device tree, but the level on the PA6 is still high. I can easily control the level through libgpiod (gpioset gpiochip0 6=1 or gpioset gpiochip0 6=0), it works. But I ca…

Hello, I have been trying to get sound working on my Orange Pi Zero 3, and I am facing persistent issues. I installed every operating system listed on Armbian’s Orange Pi Zero 3 page and followed all the standard setup procedures. Despite updating all packages and even performing kernel updates, I have never been able to get any sound output from the device. I have checked multiple configurations, tried different OS images, and ensured that all drivers are up to date, but nothing works. The device otherwise functions normally, but audio simply does not come through under any circumstances. Could you please provide guidance or a solution? Any help would be g…

I'm trying to install mpd and I'm getting an older version than I'd expect. I'm expecting 0.19, but getting 0.16. I've done the apt-get update. Am I missing something?

Hello Forum, please excuse my bad English. I try setting up a stratum1-server. Based on GPS. For this I use the Banana Pi with kernel 4.6.2 and the Adafruit GPS. The GPS is connected to GPIO J12 and works. RX/TX is not the problem. The problem is the right pin for the PPS-signal. dmesg|grep pps* [ 0.001207] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.067281] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 [ 3.260009] pps_core: LinuxPPS API ver. 1 registered [ 3.260018] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>…

Hi there, I installed the Desktop version of Jessie, it was working good, but after I wanted to check the Server version too "Armbian_5.14_Orangepione_Debian_jessie_3.4.112.7z", but it just wont boot up, no Led's glows up on the board. Tried more times to install on different MicroSD cards, but I got the same non boot results. Just to mention that the Desktop version is working on all MicroSD cards I tried! Thank you for your answer! Kind regard

hi, since 2 days i am using on my Banana Pi the Debian Jessie with 4.8.15 Kernel with installed Openmediavault 3. The system is working stable, but the network-performance is less then my older Installation based on Debian Wheezy with Openmediavault 2. I tried change the MTU-Size to 9000 and overcklocking up to 1.2 GHz, booth is not possible. I don´t know why ? For the setting the MTU-Size i edited /etc/network/interfaces and added the value "mtu 9000" -> no effects I tried set the MTU over the OMV WebGUI under network settings -> no effects. ifconfig shows me MTU=1500 Booth ways was at Debian Wheezy possible. At Debian Wheezy i had overclock the …

Hi, I have a project to do and this consists of: Arduino board which work as frequency counter and OrangePi PC which will be some kind of server (mysql, python). The idea is to use UART port to communicate (send / recevie) datas from arduino to OrangePi using C, Java or python.. Here is my schema using LLC (converter between arduino and orangePC) (hope this will work ) Is there some example in C, python or java on how to use GPIO UART pin 8/10 on orangepi as serial port? For now I have installed library from: https://github.com/zhaolei/WiringOP and second for python from: https://github.com/duxingkei33/orangepi_PC_gpio_pyH3

Hi, i try to use my orange pi one armbian to do uart debug on orange pi 2g iot I use uart3 on orange pi one and my configuration [uart0] uart_used = 0 uart_port = 0 uart_type = 2 uart_tx = port:PA04<2><1><default><default> uart_rx = port:PA05<2><1><default><default> [uart1] uart_used = 0 uart_port = 1 uart_type = 4 uart_tx = port:PG06<2><1><default><default> uart_rx = port:PG07<2><1><default><default> uart_rts = port:PG08<2><1><default><default> uart_cts = port:PG09<2><1><default><default> [ua…

Hi, I've tried setting up an SD Card to boot from and I'm getting the strangest issues. I've tried multiple images and even compiled my own and I'm getting the same issue. I'm booting from SD Card because I have the stock ubuntu running on the emmc right now and I don't want to flash that until I know the image works the way I want it to. Here are the logs I've got from the console on boot. I followed the directions with 7z and Etcher from the documentation page. Thanks for the help! starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage…

Hi.Can you help me fix this problem.Can't use usbwifi wl167g(need like reciever). Network-manager show(wifi enable) but firmware missing. Tried to install RT73_linux_STA_DRV1.0.3.6, have error, when step make, rtmp_main.c error "-march=i686". In new version desktop ubuntu wifi working, but shows slow video(I guess many improvements "use" a lot of resources).

Hello, Is a native 240p timings/resolution possible from the OrangePi PC via the A/V jack? I'd like to use it hooked up to a nice CRT for emulation.

Hey there, I have two questions and one of those may be pretty dumb, but anyway. What is the issue that the onboard network is disabled at the moment? The other question is about the tested 3rd party hardware which include various LAN and WLAN adapters. Have those indeed tested with the current experimental images and working? Or is the network support disabled in the current builds at all? Best regards Werner

my opi pc only hosts smb/nfs/transmition, very hot at summer. Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i System load: 0.23 0.23 0.22 Up time: 68 days Memory usage: 28 % of 1000MB IP: 192.168.2.99 CPU temp: 65°C Usage of /: 26% of 7.2G when I change cpufreq gov, find no cpuidle driver, is that true? upstream status about cpuidle driver? I have to disable 2 cores to cool down, and also change cpufreq to ondemand.

The software download page for the Cubietruck only has the new Armbian Stretch images available to download, are the images for the previous version Armbian Jessie still available to download? I'm thinking of updating to Stretch but would like to have the option of going back to Jessie. I have tried searching but to no avail. Thanks.

Hello, I am going to start looking into running Docker on OPi +2E soon, but before I get stuck in details I would like to know whether other people have had experience with it..? In particular, I would like to know what to expect when trying to run Docker on an OPi +2E. Having a report from prior experience would be helpful. As far as I understand, Docker is still in pretty much experimental stages on ARM. Kind regards, @ullbeking

Just yesterday I connected a 120GB Sata and transfered root using armbian-config to sata drive. After 1st boot the system was working. But when I did a shutdown and rebooted the Bananapi it stops booting. I cannot use. Help me restore the root back to SDCard.

gpio load i2c modprobe: FATAL: Module i2c-sunxi not found in directory /lib/modules/4.14.111 By looking at example of WiringPI (for Raspberry), I tried the above command, result is shown. I'm newbie, so I need to figure out how to send commands via i2c to an external device. But first, how do I even enable i2c on Neo Plus2? Or is it enabled on default? I saw on this forum suggestion to add: a line "overlays=i2c0 i2c1" in /boot/armbianEnv.txt However, my boot directory is full, so and I get error 514 whenever I try to add anything to armbianEnv.txt (which is empty) Here's disk usage: I added 10K pull up resistors between…

**Is this the correct location, or it should be at the other supported boards? It seems that DT overlays are not working root@orangepizero2:~# cat /boot/armbianEnv.txt verbosity=1 console=serial disp_mode=1080p60 fb0_width=1280 fb0_height=720 rootdev=UUID=b8899b39-b6cb-4718-bdbb-e1b39816db74 rootfstype=ext4 overlays=w1-gpio param_w1_pin=PC9 param_w1_pin_int_pullup=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Boot log: Spoiler [41]HELLO! BOOT0 is starting May 13 2020 14:10:04! [46]BOOT0 commit : 593cf83 [48]set pll start [51]periph0 has been enabled [54]set pll end [56]unknow PMU [57]PMU: AXP806 [64]vaild para:1 select dram …

After orangepiplus upgraded the kernel, the native wifi interface card disappeared. Output log of sudo armbianmonitor -u: https://paste.armbian.com/ilufiwukav Currently, after upgrading the kernel to 6.6.36-current-sunxi, the native wlan0 will disappear.

Sep 6 20:28:27 localhost kernel: [ 338.014558] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !! Sep 6 20:28:27 localhost kernel: [ 338.014618] sunxi-mmc 1c12000.mmc: data error, sending stop command Sep 6 20:28:27 localhost kernel: [ 338.352288] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !! Sep 6 20:28:27 localhost kernel: [ 338.352333] sunxi-mmc 1c12000.mmc: data error, sending stop command Sep 6 20:28:28 localhost kernel: [ 338.689971] sunxi-mmc 1c12000.mmc: smc 1 err, cmd 53, RD DTO !! Sep 6 20:28:28 localhost kernel: [ 338.690044] sunxi-mmc 1c12000.mmc: data error, sending stop command Sep 6 20:28:28 localhost kernel: [ 338.690091] brcmfmac: brc…

hi there, i was setup linux-wheezy-root-cubietruck 4.2 on cubietruck nand.these days i upgrade system it show me a error message: Unpacking replacement linux-wheezy-root-cubietruck ... dpkg: error processing /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb (--install): unable to make backup link of `./boot/bin/lime.bin' before installing new version: Operation not permitted Errors were encountered while processing: /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb i thik this is a bug because dear developer don't think about when system install to nand later some problem. how to fix? thanks!! 估计用CT的很多是…

hello, Exist a way to install armbian on my A13-OLinuXino-WIFI ? Best Regards