Allwinner sunxi

Hi all, its probably something simple but here is what i am struggling with: airmon-ng start <interface name> iwconfig wlan1mon channel 13 aireplay-ng --test wlan1mon ifconfig wlan0 up -> wlan0 is configured and connected to the access point packets are injected and can be observed with another machine ifconfig wlan0 down / or not associated with network packets are not injected and cannot be observed aireplay-ng or raw socket directly shows no errors initial toughs somewhere there is a switch to enable/disable radio at low level nothing obvious in strace tried with and without network manager…

In this post tkaiser says disabling HDMI and the GPU on H3 boards can reduce power consumption by 200mW. Is it possible to do this on a headless Orange Pi Zero 2+ H5? I don't believe I can use h3consumption or edit FEX files because I'm on the H5 mainline kernel. I tried setting monitor=none in armbianEnv.txt, but I didn't notice any appreciable difference using an inline USB power meter.

I'm trying to make working 3.5" 320*480 TFT SPI display with touch screen on NanoPi K1 Plus with Armbian 20.05.2 (kernel 5.4.43). For now it works, but the touchscreen has issues. In empty `startx` session cursor works for few minutes and then hangs, restarting `startx` make it working again for a while. If I try to run x session with chrome, the cursor hangs immediately. openbox-session & chromium --no-first-run --disable --disable-translate --disable-infobars --disable-suggestions-service --disable-save-password-bubble --start-maximized --kiosk --disable-session-crashed-bubble Any ideas how to fix it? Screen image Sp…

Hi there 👋 I'm using a NanoPi Duo2 with Armbian 21.08.1 Bullseye and Linux jenkins-agent-arm32 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux I want to use an SPI screen on it, but I don't know which library to use to handle the GPIO... I've tested quite a few and none of them seem to work. I have enabled SPI and I2C in `armbian-config` and `sudo i2cdetect -y 0` works (even if nothing is found), but what is the next step? sudo i2cdetect -y 0 [sudo] password for poddingue: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- --…

I downloaded: http://mirror.igorpecovnik.com/Armbian_5.10_Pcduino3nano_Debian_jessie_4.5.2_desktop.7z and burned it to an SD card, when I tried booting the board, all I get on the uart console is the u-boot SPL signon message +++++++++++++++++++++++++++++++ U-Boot SPL 2016.01-armbian-sun8i (May 01 2016 - 01:05:19) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Could not determine boot source resetting ... +++++++++++++++++++++++++++++++ This repeats forever... I had previously used: http://mirror.igorpecovnik.com/Armbian_5.00_Pcduino3nano_Debian_jessie_4.4.1.zip and it worked fine on the same board. I tried recompiling u-boot from source u…

Orange pi is only sending data with tx pin next to the ethernet port. Target is an arduino leonardo clone 5v 16mhz clocked. Maximum baud rate i could run is 115200 8bit data,no parity ,1 stop bit. Shouldnt be i able to run at higher baud rates like 1m? Libraries i am using https://github.com/wjwwood/serial http://www.fourwalledcubicle.com/files/LUFA/Doc/120219/html/group___group___serial___a_v_r8.html

How enable tv out on mainline kernel 4.19? script.bin not found and stevenj/h3-tve not working on my version of kernel.

I'm sorry, I wrong section of the forum. Question here https://forum.armbian.com/topic/11607-h3-nanopi-neo-core-on-kernel-4x-audio-clickpop-dapm-how-disable-it/

Dear all, I need your help. I've built a fresh pcDuino3 firmware: Armbian 5.14 Pcduino3 -default - Debian 8 Jessie - CLI - Kernel 3.4.112 And now I'm trying to enable UARTs (2, 5 and 6). I've edited script.bin and now I got 4 ttyS devices. Could you please tell me how to "atctivate" those UARTs and which pins shoul I use. I guess that UART2 (ttyS1) uses D0 and D1 pins UART5 (ttyS2) uses SPI0_CS and SPI0_CLK pins UART6 (ttyS3) uses SPI0_MOSI and SPI0_MISO pins Am I right ? And how to enable ttySs? I tried following for the UART2 echo 1 > /sys/class/gpio/export echo 25 > /sys/class/gpio/export I attached my fex. file and pcDuino3 schema Unfortu…

I bought a 7inch HDMI LCD (C) panel http://www.waveshare.com/7inch-HDMI-LCD-C.htm and trying to use it with Orange Pi One. All is right, but: 1. the image constantly flickers 2. when the brightness changes, a "ghost" of the old image appears I use power from PC power supply, yellow line, armbian image is Armbian_5.30_Orangepione_Ubuntu_xenial_default_3.4.113_desktop Can I do something with my configs, or this panel is a piece of shit? My fex: [boot_disp] advert_disp = 0 auto_hpd = 1 output_type = 4 hdmi_channel = 0 hdmi_mode = 4 cvbs_channel = 1 cvbs_mode = 11 output_full = 1 hdmi_mode_check = 1 screen0_out_c…

Can any one port the driver for ms5611 from kernel4.x to 3.4.39? I am using the sensor on olimex a20 micro 4Gb. I need it to use it in Android. I am willing to pay for porting.

So first I'm new using armbian on Opi PC. I'm trying using my Opi like a mediaserver on my TV. I install Kodi and everything is ok. I'm now trying to fix some Audio problem. When I watch e video on Youtube, some of them have e perfect sound, some of them have a lot of interferences, so mutch that I can't hear anymore anything of the video. I already configure asound.conf with the card I'm using, i tried already using only HDMI for video and audio or to separate HDMI only for video and 3.5 jack for audio. Both solutions are giving me the same problem. I install every codec I found, also the vlc complete with the browser-plugin, but no way. I t…

EDIT - UPDATE 'apt-get upgrade' worked fine - thanks to all armbian developers and contributors! --- Hi, Should I wait for 'apt-get upgrade'? ... never change a running system ;-) Due to Ethernet Port (LAN) related issues that effect OPI0+ to the newest Armbian release - under development (Now it seems that the OPi Zero Plus is missing his Ethernet-device ...). My OPI0+ is only connected via LAN cable to the router. And I don't like to use Wi-Fi (WLAN). Regards, Jochem

Hi everybody. I'm stuck on working touchscreen with banana pro running vanilla jessie desktop. My touchscreen has goodix controller that supported mainline kernel. But when i install goodix driver module, an error that saying "request IRQ failed" show up in dmesg. I think i need to inform module for right interrup and reset pins connected board, but how? i'm connected int pin of touchscreen panel to pin7 that labeled "io1" on board. Please help me. links: goodix driver source, banana pro pin definition schema

Hi all, Somebody has any problem with NanoPI NEO using g_hid as keyboard ? I'm using the code below to send the keyboard report to /dev/hidg0, but the it throws an error. https://www.kernel.org/doc/Documentation/usb/gadget_hid.txt NanoPi NEO - Linux 3.4.113-sun8i jessie [ 373.427509] g_hid gadget: adding config #1 'HID Gadget'/bf064548 [ 373.427678] g_hid gadget: adding 'hid'/c527075c to config 'HID Gadget'/bf064548 [ 373.427782] gadget_is_softwinner_otg is not -int [ 373.427837] gadget_is_softwinner_otg is not -int [ 373.427881] gadget_is_softwinner_otg is not -int [ 373.427932] gadget_is_softwinner_otg is not -int [ 373.429424] g_hid gadget: cfg 1/bf064548 s…

Hi everybody, I'm trying to build an owncloud server with my Cubieboard2 dual card, using a Debian Jessie based rom. I download both the Vanilla and legacy versions, but when I put them on the SD.. the system does not boot! The official images hosted on sunxi servers are different between the "normal" version (with NAND) and mine (with two sd slots, 1 for boot and 1 for data, but no NAND). It could be this the problem? I'm also trying to start with a clean debian installation trhough official installer for armhf but no success. Thanks a lot and have a great end of the year!

I've download Armbian_5.25_Cubieboard2_Ubuntu_xenial_default_3.4.113_desktop (Ubuntu desktop – legacy kernel ) and copie with dd on a 32GB EVOSamsung sd-card. After boot until loading Kernel , the Loading crashd and the board goes off. What can i do? best regards mtpmoni

I tried to install default linux kernel (3.4.113) on Orange Pi PC + and It's keep on rebooting while displaying kernel panic on console. Below I have attached the log U-Boot 2017.11-armbian (Dec 18 2017 - 14:24:28 +0530) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC Plus DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 In: serial Out: serial Err: serial Net: phy interface0 eth0: ethernet@1c30000 starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scan…

Hi. I encountered problem, glimpsed through topics and didn't found anything similar so I am posting this one now. Had set up OrangePi Zero 256MB version with Domoticz and everything looked great. I have 2 internet connections, one is PON FTTH and the other one is VDSL. So I have 2 routers with RJ45 and 2 WiFi networks at home. One for my personal usage (ftth, locked router by ISP, static IP but no port forwarding) and the other one is for all home users (dynamic IP but full access to router options). I hooked up OPI using cat5e cable to my router and this connection is working perfectly reliable. I had XR819 hooked up to VDSL router as auxiliary connection (and con…

For a new project with multiple socs, I want to use the NanoPi Neo 2 with the Allwinner H5 soc and boot from DHCP / NFS. I've done the same in the past for a setup with Raspberry Pi's, but the Allwinner socs require a different approach. What would be the best way to achive this? - FEL? - SD or USB with U-Boot? - any other suggestions?

with great joy we saw the new version of Armbian_5.69_Orangepipcplus_Ubuntu_bionic_next_4.19.13 for orange pi pc plus (date 9-1-2019) We were waiting for a WIFI fix, on the WPA. Wifi at the very beginning, it works properly with a WPA connection. Then, you do not want to make another WPA connection and work. Will this problem be corrected in some new version of Armbian? Thanks

Does anybody got the SPI Bus working on cubietruck. I have a /dev/spi32764 device (for SPI2) after changing dts/dtb file. but ioctl always returns -1. Same test program worked with legacy kernel. Is there anything else todo?

Hey all, I'm using U-boot 2017-09 and Kernel 4.13. I'm looking for a way to disable the board auto start. I'm explaining. When you plug the power in, the board start by itself and U-boot does the rest. I would like to disable this feature in order to be able to plug in the power, charge the battery if needed and start the board with the regular push button. Is there any tweak to be done in the Device Tree ? Thanks Florian

Old post below, here is what I found out thanks to some help from linux-sunxi IRC, I think this is a bug in the ondemand governor When using ASIX AX88772B USB to ethernet adapter and the cpu-governor is on ondemand, transfer speed is very slow. If governor is set to conservative or performance (yes that's right) speed is ok, 50 Mbit at least. So the problem has nothing to do with cpu speed as such (it's working @ steady 480Mhz and @ steady 1200Mhz) for now I'll stick with conservative as I don't want my board to burn up, but It would be nice if someone could take a look at that ondemand governor. Additional info: …

i did some experiments today, i tested 2 Orange pi with the same image debian buster in the lastest version. i put a script on both that reported the execution time of a function and the date, one is running smoothy, the other crashes the orange, the bottom is the log what caught exactly at the time it caught, could someone help me understand it? Mar 19 09:25:01 localhost CRON[1657]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Mar 19 09:30:01 localhost CRON[1702]: (root) CMD (/usr/lib/armbian/armbian-truncate-logs) Mar 19 09:31:52 localhost systemd[1]: Stopped target Timers. Mar 19 09:31:52 localhost systemd[1]: Stopped Message of the D…

Ran the following command on my Banana PI to move to the HDD (SATA) nand-sata-install Install was a success: However I think some stuff went wrong during the transfer. Whenever I open a file in nano I get the following error: Error in /etc/nanorc on line 260: Error expanding /usr/share/nano/*.nanorc: Inappropriate ioctl for device I cannot run apt-get update anymore: pi@bananapi:~$ sudo apt-get update && sudo apt-get upgrade Hit:1 http://security.debian.org buster/updates InRelease Hit:2 http://deb.debian.org/debian buster InRelease Hit:3 http://deb.debian.org/debian buster-updates InRelease Hit:…

dear igor .. see #63 https://github.com/igorpecovnik/lib/issues/63

Hello I have an issue with my wifi, it's not reliable. There is no problem with my laptop, or any other devices on my network, but my NanoPi Neo is disconneted after a few hours. It can stay alive for an half a day, and after it become unreachable. As I have no other connection to my NanoPi it's a bit hard to establish what appens. But if I unplug the USB Wifi dungle, and replugged it the link come back. Doing a ping to the NanoPi, I see regular "Request timeout for icmp_seq" - every 20, 50 or 100 request, it depends - and sometime the request time is abnormally huge: serveral seconds. The config has bee done with nmtui, the…

Hi guys, I've been busting my head for days now trying to find a way how to permanently change MAC address on my ehternet on Opi Win Plus boards but nothing yielded positive outcome. The reason I need to permanently change MAC address is because I'll be running 6 of these boards on the same network and since all of them have identical MAC it's impossible for my router to manage them properly. I'm running Ubuntu_xenial_default_3.10.107_server with legacy kernel. I've tried changing the /etc/network/interfaces file by adding hwaddress ether xx:xx:xx:xx:xx:xx , changing from static to dhcp and doing all sorts of combinations in hopes that so…

Hello, There are two physical USB port on the pi zero+ board : one is USB 2.0 host and the the second one is USB 2.0 OTG through a micro USB connector. As I power the card through the expansion pin I would like to turn the micro USB to a regular mode to connect a DVB dongle. With Armbian 5.38 and Kernel 4.14.14 (and also nightly build) I've done the following modification - in armbian-config enable usbhost0 - modify the /boot/dtb/allwiner/sun50i-h5-orangepi-zero-plus.dtb => decompile the file with dtc => edit the dts file and change the line dr_mode = "peripheral" to "host" => recompile the file and reb…

I am use igors lib to get an suffucently patches kernel source for bana Pi R1 and for test builds i use this script for my unattened kernel builds. This allows directly install an fresh kernel and make an backup of the old kernel. my custom kernel .config is then at $REL stored and used . usage path : run igors compile.sh , wait till the source download done , do an CRTL-C once the kernel wants to compile from his lib then i.e : fw1 /t/GIT/output/linux-mainline # cp .config /t/GIT/.test5 fw1 /t/GIT/output/linux-mainline # /t/GIT/build.sh Usage: /t/GIT/build.sh {build|timestamp|clean|install|ins…

I'm having difficulty getting Octoprint to start. I've set it up in init.d and defaults. When I execute it directly I get an error about running as root. It's like it's ignoring the octoprint_user. /etc/default/octoprint: # Configuration for /etc/init.d/octoprint # The init.d script will only run if this variable non-empty. OCTOPRINT_USER=octoprint # base directory to use #BASEDIR=/home/octoprint/OctoPrint # configuration file to use #CONFIGFILE=/home/pi/.octoprint/config.yaml # On what port to run daemon, default is 5000 PORT=5000 # Path to the OctoPrint executable, you need to set this to match your installation! DAEMON=/home/octoprint/OctoPrint/…

Im trying to connect WaveShare 10" Touch Screen LCD (HDMI) to OrangePI Plus 2E but the problem is that I got greeny picture on the screen. If I connect this display to Raspbery PI 3 I got good clear picture. Any ideas what could be wrong and how to fix it?

I have a orangepi board with H6 , it have BSP android 7 firmware. Now , I can enter BSP uboot shell. want to find a way to boot mainline kernel instead of BSP kernel. How to do that ? Any help would be much appreciated. EDIT: On amlogic arm64 board can use go command to load mainline u-boot , Does allwinner board have the similar way to do that ?

Hi all, I try to work with Pine64 7" inch LCD on Pine64 A64 board but not working I just modify /boot/armbianEnv.txt for add pine64_lcd=on and add the module how is described on the installation iso, but nothing happens. In the boot file I have found dispmode directive because when installed I used hdmi port to see first boot. Please Help me!

First sorry for starting a similar thread here and in [1]. I try to read a DS18B20, which does not work with Armbian, DietPi, and Friendlyarm's Ubuntu. This morning, my idea was to slow down the CPU - and it worked. In detail: By running some useless cpu consuming python scripts, reading the DS18B20 works fine. As soon as i stop them, reading the sensor immediately fails. So there might be some timing issues in the implementations of w1-gpio and w1-gpio-board. Are there any hints how i can get these issues fixed? Thanks! Thomas [1] http://www.friendlyarm.com/Forum/viewtopic.php?f=47&t=393

Guide: Configuring Orange PI PC to receive IR/InfraRed and fix Lirc I also show how VNC can be used to do remote control on orangepipc+ on the example of kodi. Should be the same on orangepipc boards. If a USB IR receiver is used the problem ma not be present at all, but i use the on-board IR receiver. Is dirty work around, if someone knows how to fix it correctly please tell! (I installed the latest version of LIRC 0.9.4b from the source code and compiled it, but it din not fix the problem. So i stay with the version ARMBIAN 5.25 stable Ubuntu 16.04.1 LTS 3.4.113-sun8i comes with.) If the LIRC tool irw cant be started and …

Hello everyone, I want to do something simple with my OrangePi One Plus. That is to connect a bluetooth speaker and play wireless from the Pi with a CSR8510 A10 USB dongel. The dongel works and i can pair with every device. Even with my JBL Go 2 bluetooth speaker: hj@PLUS-OrangePiOne:~ $ sudo bluetoothctl [NEW] Controller YY:YY:YY:YY PLUS-OrangePiOne [default] Agent registered [bluetooth]# power on Changing power on succeeded [bluetooth]# scan on Discovery started [CHG] Controller YY:YY:YY:YY Discovering: yes [NEW] Device XX:XX:XX:XX JBL GO 2 [bluetooth]# scan off Discovery stopped [CHG] Controller YY:YY:YY:YY Discovering: no [CHG] Device XX:XX…

Hi, When I scan the I2C with i2cdetect, I get the following, without connecting any i2c device. May I know which device on the motherboard is taking up the three addresses. Thank you sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: 50 -- -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -…

I use one of my Cubietrucks to operate two IR-read/write heads to read out powermeters. Sometimes some kind of error happends and the device get's disconnected (not physically, but from system): dmesg output: [434913.929842] ohci-platform 1c14400.usb: frame counter not updating; disabled [434913.939546] ohci-platform 1c14400.usb: HC died; cleaning up [434913.947863] usb 3-1: USB disconnect, device number 3 [434913.949632] cp210x ttyUSB0: failed set request 0x0 status: -19 [434913.959197] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [434913.959273] cp210x 3-1:1.0: device disconnected I can fix it by rebooting only, also unpl…

Hi, I'm working or orange-pi Zero(H2+) broad with sunxi mainline 4.14.15 kernel. I didn't find any support of Thermal or temperature driver in that. How can I add support of that?? From where I can download the Driver ? How to enable it? Please give suggestions.

please enable green led Banana-pi M1 Armbian 5.75

hi all, if someone need, I adapted for nagios the script to monitor battery cubietruck. The script is pnp4nagios friendly. #!/bin/bash ###################################################################################### # # Battery info # /usr/sbin/i2cset -y -f 0 0x34 0x82 0xC3 # read power OPERATING MODE register @01h POWER_OP_MODE=$(/usr/sbin/i2cget -y -f 0 0x34 0x01) BAT_EXIST=$(($(($POWER_OP_MODE&0x20))/32)) # divide by 32 is like shifting rigth 5 times CHARG_IND=$(($(($POWER_OP_MODE&0x40))/64)) # divide by 64 is like shifting rigth 6 times ######################################################################################## #read battery voltage…

Hello, We have our A20 machine with a sdio wifi device Realtek 8723bs which is not included in the current kernel's modules, then when we try to cross-compile them in a PC it fail requiring kernel version 3.19 or later, i think mainline kernel could be a way to go or upgrade 3.4.x to 3.19.x, but some text claim unsupported nand in mainline which is required by the project and don't know the correct way to make it go to 3.19 in sunxi allwinner scenario. What do you think is the best way to make it work better, any clue please? Thank's in advance Daniel

Hi to all, I am using a cubietruck as an alarm camera detector with eyeone, but now i want to have new life for it ... Is it possible to output from vga a 15khz CRT signal to connect to a CRT tv 384x224? Thanks for all...

1-Wire works, I put the explanation at the end of this post. Hello There, yesterday I burned a fresh image of Armbian_20.02.5_Bananapi_buster_current_5.4.26 to replace my current setup (Armbian_5.91_Bananapi_Debian_buster_next_4.19.59) and I run into some trouble with 1-Wire. I tried everything I knew and found on the web but 1-Wire still won't work. So I need some help. My hardware setup was not changed and it worked for at least two years. So would rule out a wiring problem at the moment. My SoC is a Banana PI M1 ( http://www.banana-pi.org/m1.html ) The strange thing is, that 1-Wire wont come up by itself, I have to run mo…

I have a question, does anyone know a method to start in the Opi Lite system the I2S audio interface and in particular I mean the module: PCM5102 / PCM5102a On my old OrangePi Lite board, sound and audio in the configuration as mentioned above really work great ... but unfortunately the Armbian system that I use is no longer supported. This is the Ubuntu version (xenial) and kernel: 3.4.113-sun8i, I managed to update some programs important to me, e.g. mpd / mpc but not to the latest versions. I also have another version of OrangePI 3 LTS and I know that on this model it is rather impossible to start I2S + PCM5102 so I used a good sound card under USB and it is OK. Ho…

Hello i am running armbian wheezy with the legacy kernel on an olimex a20 lime. I have atached an audio jack to the gpio pins. But cant get any sound on the output using speaker test. Do i need to do some configuration to get this to work ?

can somebody help me create an ap using hostapd i was following this turorial https://seravo.fi/2014/create-wireless-access-point-hostapd but when i chirantan@orangepizero:~$ iw wlan0 info Interface wlan0 ifindex 4 type managed wiphy 1 i cant change the type to AP

Hello I am new in this forum, I need to configure A20-OLinuXino-MICRO 4G Nand board so that it has native vga output. As I can do, please, please, that any member of this forum can guide me.

hi how can i enable the tv out in orange pi PC+, I need to do a kiosk mode thanks

Hello there, i have one orange pi pc 2 and i need to put this work with 2-Channel Isolated CAN Expansion HAT from Waveshare (2-Channel Isolated CAN Bus Expansion HAT for Raspberry Pi, MCP2515 + SN65HVD230 Dual Chips Solution, Multi Onboard Protection Circuits (waveshare.com) But im stuck with .dts and overlays. This HAT was design to work with raspberry pi but i know we can put it to work with orange pi. My problem is with "chipselect" cause our GPIO pin configuration are diferent then Raspberry Pi Could you please give me an example how should it be my .dts?

I've been using a Cubieboard2 and I have been struggling to get the SPI to work. I've edited the armbianEnv.txt and added the spi0 and spi-spidev to the overlay line. I see the overlays being loaded and I get (only when I've got the spi-spidev overlay on) a /dev/spi0.0 In the dmesg I see a line like "scanning for SPI0 on DT" (paraphrasing as I don't have the screen in front of me ATM.) I don't see any other diagnostic about the SPI though. I haven't jumpered the MOSI to the MISO yet (for a "loopback" test) The kernel is compiled with the sun7i-SPI driver as well as the usermode spi driver. Is this al…

hi i would like to install vlc 2.2.7 or vlc 3 on armbian xenial 5.90 stable two month ago i used to do apt-get upgrade & apt-get update then vlc 2.2.7 can be installed no problem now even apt-get upgrade break the system and i get two instance of desktop now i only get vlc 2.2.2 wich have bugs is there a way to install vlc 2.2.7 at least ? orange pi one

I have a working BPi M1 with [ 0.000000] Linux version 5.15.25-sunxi (root@d72d155687c7) (arm-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #22.02.1 SMP Sun Feb 27 09:23:25 UTC 2022 Due to inconvenient USB placements, I thought using OTG micro USB (the one right next to the SD slot), but it doesn't seem to be operational. I bought a Micro USB Male To Female OTG Adapter Cable, but the attached devices are not detected neither connected to OTG port, nor to the normal power-in micro USB connector (lo…

Hello all! I'm running armbian on a cubietrack wich I use for transmission and samba purposes. The Cubietrack is always on, and today I realized that was responding to ping but I couldn't log with ssh. When I restarted the system it hanged on this screen: The Cubietrack have ping response, but can't do anything. Any ideas? Thank you!

hi guys I'm amateur Linux user. now i can connect to internet with WiFi but i don't know how connect to internet via LAN (Ethernet) my problem is Ethernet setup . please help me for make small network with 2 or 3 client With the ability to share internet and file. my boards : 1 orange pi PC plus( Intended for server ) , 2 orange pi Zero 512Mb ( Intended for client ), network Components : LinkIt Smart 7688 (WiFi to Ethernet Bridge ) D link 8 port switch I'm so sorry for bad English

Hello! I have: 1) Orange Pi PC+ with ARMBIAN 5.38 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i 2) Orange Pi Zero with ARMBIAN 5.60 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i 3) Orange Pi PC with Debian 3.4.39 #1 SMP PREEMPT Wed Sep 16 13:39:07 CEST 2015 armv7l On both ARMBIANs I have noticed: every start of arecord sets level on "MIC1 boost AMP gain control" audio setting with constant value 5. I think it uses value of "cap_vol=5" from section [audio0] from script.bin. On Debian it does not. In my case I need very very very low value of "MIC1 boost AMP gain control". Value of "ADC input gain ctrl" is alread…

verry bad screen with armbian-config and alsamixer using ( lxterminal, mate terminal, putty on Linux mint Buster ) works better with xterm , on previous armbian version Jessie or stretch it's fine with all terminals . 2 first screenshoot are made on lxterminal , third on putty . the 4th one is my dialog menu and it's ok on all terminals

Hi, anyone used this driver with success on A20 legacy? This is what i get: Seems that it can load ethernet and mass storage without problem but it fails on serial. If I run g_serial alone it works: Any ideas?

Just to inform interested people. I tested mainline nightly release. Monitor switches on shortly without something visible and than goes off with "no signal". Dmesg shows: root@orangepipc:~# dmesg|grep frame [ 3.251293] simple-framebuffer 7e05c000.framebuffer: framebuffer at 0x7e05c000, 0x1fa4000 bytes, mapped to 0xf1c80000 [ 3.251303] simple-framebuffer 7e05c000.framebuffer: format=x8r8g8b8, mode=3840x2160x32, linelength=15360 [ 3.401661] Console: switching to colour frame buffer device 480x135 [ 3.550976] simple-framebuffer 7e05c000.framebuffer: fb0: simplefb registered! fbset shows: root@orangepipc:~# fbset mode "3840x2160" geometry 38…

I have a encrypted external hard drive connected via USB. I want to be able to automatically access it after boot so I made a keyfile that I put in /etc/crypttab. After updating the crypttab file I ran update-initramfs -u. But after reboot the drive is still locked. Why is this? I suspect it might be because of the order of things at boot. Maybe crypttab is called before the USB device is initialized? Any help would be appreciated. Edit: I had a incorrect crypttab that's why it didn't mount. It works now thanks!

Armbianmonitor: http://ix.io/2g5I I recently started playing around with OrangePi Zero with the Allwinner H2+ CPU. I want to test out the internal audio DAC. To do so I enabled "analog-coded" in armbian-config. After rebooting I saw a new audio device in the output of "pacmd list-cards", but it says that only mono is available. How can I configure stereo sound? I haven't played around with "/etc/asound.conf" much as I don't understand it. Also, I don't have anything plugged into the audio pins on the GPIO.

Have not been able to confirm if it is possible for the Orange Pi Zero to act as a virtual mass storage device. I would like to be able to plug this into a device and have that device treat the Pi Zero as a USB drive, and write to the on board SD as such. I believe this requires USB on the go so that the device can be USB slave. Any input on the topic is appreciated. I know the Raspberry Pi Zero W supports this, but I think i will have better luck with the wireless having an external antenna on the Orange Pi Zero.

I'm working on a Duo project that needs SPI and this is how I configured and tested it without the mini shield. Requirements: NanoPi Duo with test Armbian image 1 female to female jumper wire Enable SPI on boot: sudo nano /boot/armbianEnv.txt Add spi-spidev to overlays= Add line param_spidev_spi_bus=1 sudo reboot If everything worked you should have /dev/spidev1.0. Check with ls /dev/spi*. Now we can test with a C program: cd wget http://www.raspibo.org/renzo/spidev_test.c gcc -o spidev_test spidev_test.c sudo ./spidev_test -D /dev/spidev1.0 spi device: /dev/spidev1.0 spi mode: 0 bits per word: 8 max speed: 500…

Hello, I am using the Armbian 22.08.2 Jammy with Linux 5.15.69-sunxi. When I issue "aplay /usr/share/sounds/alsa/Front_Center.wav" or "speaker-test -t wav" playback misses a few seconds from the beginning of the audio file. If I restart it immediately, I can hear the file playing correctly. Then I wait for a while, run it and the problem reappears. I read on this forum that people have had the same problem for years without finding a solution. Is there a solution or does anyone wise know what the problem is?

Hello, I try to enable audio linein, controls with alsamixer are the following. Is it possible to redirect audio input to output directly or with audio equalizer ? I actually have sound with a speaker test, but I can't listen to the audio line-inActually I have sound with speaker test, but I can't listen audio linein Best regards

Hello. I soldered CR2032 battery to BAT1 on Banana pro board. Setup current date and time. But RTC not working. :-( When I restart the board I see old date and time. Please tell me, how can I turn on RTC?

I bought orange pi win plus and I began to use armbian. Nearly everything ok but I can not use my bluetooth keyboard. There is a bluetooth symbol and I can enable it but when I wanna add my keyboard it says no adapter found... Please help me ..

I have a problem with my wireguard implementation. When connected through it I get lag spikes every few seconds. What might be the cause and solution to this? It is not the internet connection/cable/etc because a raspberry pi running wireguard works fine on the same exact cable, port etc.

Hi there, I'm trying to run luma.examples using an SSD1322 display via an SPI interface. I think I got the wiring right but the software is responding with errors. The app is expecting D/C and RESET parameter via a GPIO pin numbers to control the display.. I'm not sure how the Nano PI NEO Air physical pins are mapped to a GPIO port under Armbian. Where can I get a list of mappings for the physical pins to the GPIO pin numbers? How does this work? Is this an OS specific thing? Thanks in advance. PS: `uname -a` : Linux nanopiair 4.14.15-sunxi #23 SMP Sun Jan 28 12:46:39 CET 2018 armv7l GNU/Linux

Hi, I try to change the language of the last OS Buster of a Cubietruck 3 in FR. The language is always in US. Thanks

Hi, I want to use LCD on Orange Pi 3 LTS. But there are no fex/script.bin in the boot directory. The LCD pins are given the RGMII Ethernet Interface. I could not configure the device tree for internal LCD output. Could you please explain how can i use LCD on these system ? Good Work.

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

I'm trying to enable GPU support for watching youtube on orange pi 2 zero w model. But there is no Mali driver and even kernel package How can I enable this?

I use 4.14 image from https://www.armbian.com/banana-pi-pro/ I try to enable vdpau and switch from next to legacy kernel on Armbian Bionic (linux-image-sun7i). And got an hangup at "Starting kernel..." message. Set verbosity "9" and mkimage doesn't help. Why no bionic desktop images for banana pi pro? Did you drop support for legacy kernel on bionic for old bananas? For xenial, bananapipro.bin exists in package linux-xenial-root-bananapi. wget https://apt.armbian.com/dists/xenial/main/Contents-armhf.gz -O-|zcat|grep bananapipro.bin But this file not found for bionic: wget https://apt.armbian.com/dists/bionic/main/Contents-armhf.gz -O-|zcat|grep bananapipr…

Hi there I have a banana pi M1 and I have installed Armbian on it. The HDMI output / Display work fine if I have HDMI connected to the HDMI port of BPi and monitor/tv is turned on before Armbian booting process starts. However if I don't have HDMI connected before boot process or Monitor/Tv is not turned on then I don't see the display if I connects the HDMI or turned on Monitor later. It is a problem for me because when I want to connect to display to already booted OS. Does anyone faced this behavior? Please advise.

Ok. I'm trying to use my orange pi pc for send ir signals to my tv. I'm using lirc on an armbian stretch 9.9. the ir receiver works fine, but when I try to emit with the command: irsend SEND_ONCE tv KEY_5 (tv is the name of my lircd.conf), those ir signals that I previously recorded and saved on my lircd.conf file it shows the following error: Hardware does not support sending error running command: Input/output error Thanks in advance.

Hello, I'm using the Lime2 with 22.11(Desktop) + latest Kernel & it works like a charm. I'm currently toying around with the Mia E-Ink Display (Onyx Boox) and the display goes blank during loading the Kernel. Could the problem be that the refresh rate is not supported? The specs of the display are 2200x1650 with an refresh rate of 38 Hertz. I tried to change that via armbian-config (boot section) but it made no difference. Does anybody know a way to make it work? best

I'm having a problem installing a driver. Once compiled correctly, the system gives me an error. Note that I performed the same procedure with : RaspiOS on an arm64 board (RPi4B) with the same kernel version, and it worked. Debian 12 on a PC, and it worked. Armbian on an arm64 board (RPi4B) with the same kernel version, and it worked. Armbian on an armhf board (nanopineocore) with the same kernel version, and it worked. But does not work with Armbian Bookworm on a nanopineocore2 board: epsilonrt@nanopineocore2:~/src/tty0tty/module$ sudo modprobe tty0tty modprobe: ERROR: could not insert 'tty0tty': Exec format error …

I tried to let learn from lirc. root@cubieboard2:/etc# irrecord --driver=default --device=/dev/lirc0 /etc/lircd.conf irrecord - application for recording IR-codes for usage with lirc Copyright (C) 1998,1999 Christoph Bartelmus(lirc@bartelmus.de) irrecord: could not get file information for /dev/lirc0 irrecord: default_init(): No such file or directory irrecord: could not init hardware (lircd running ? --> close it, check permissions) What I have done I deleted the lircd.conf. Stopped lirc service. root@cubieboard2:/etc# /etc/init.d/lirc stop [ ok ] Stopping lirc (via systemctl): lirc.service. Armbian Monitor Log http://sprunge.us/TNUW

Some time before I installed iobroker on my cubietruck and since that the system crashes every now and then. Two times iobroker was not able to start anymore after a crash. After googling I found out that maybe my SD card is the problem and so I bought a SSD. Now I found out that I don't have to reinstall the system. I can simply transfer all data from SD to SSD by using nand-sata-install. Everything worked fine. System reboots. But only the SSD partition was formated and all data was transfered. The boot information was not changed. Because I have no idea about unix boot configuration I better keep my hand…

terminal command to connect 1)wifi (using username and password). 2)hotspot os i am using is Armbian_5.65_Nanopiduo_Debian_stretch_next_4.14.78.

Hello, When configuring I2C ports in armbian-config it shows 3 I2C ports (i2c0,i2c1,i2c2). The pinout from http://linux-sunxi.org/Xunlong_Orange_Pi_Zero shows only 2 I2C ports: 3 TWI0_SDA / PA12 / GPIO12 5 TWI0_SCK / PA11 / GPIO11 and 16 TWI1-SDA / PA19 / GPIO19 18 TWI1-SCK / PA18 / GPIO18 are there 3 or only 2 I2C ports ? (how to configure the third if there is one ?) thanks for your answers Jean Antoine

Hi , I am trying to install headers on my orang pi using command #apt install linux-headers-$(uname -r) getting the following message Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-headers-5.4.27-sunxi E: Couldn't find any package by glob 'linux-headers-5.4.27-sunxi' E: Couldn't find any package by regex 'linux-headers-5.4.27-sunxi' could someone help me in how do I install headers ?, I am trying to comiple a kernel module. thanks

Hi everyone, Recently I have installed armbian Bookworm on my orangepi pc and i noticed that the LEDs were not working. The system is booting with no issue and I have connected to wifi and did an initial software update and bootloader update and still the issue is persisting. So I clean installed jammy on the pi to check it again and still the led was not working. Please help me out on this issue, and if anything more is required please do let me know.

Simple to reproduce: Install armbian from Armbian_23.05.0-trunk_Bananapip2zero_bookworm_current_6.1.24.img after setup make apt-get update apt-get upgrade System will do nothing after reboot, LED stays off copying back kernel 6.1.24 brings it back to life again, with the rest upgraded. thanks Michael

Hi all, i'm trying to install Digital Persona SDK on a olimex A20. Driver and lib's are ok. So far so good but after compiling en running the exe (i'm using Debian) i got the following error "symbol lookup error: /usr/lib/libdpD00701.so.2: undifined symbol: __aeabi_uidiv." this is a soft/hard float issue, is there a way to install a debian compatible with this lib? or how to work around? manufacture DigitalPersona (now Crossmatch) doesnt give any help and i dont have source code from this lib. any help would be welcome. thx Stefan

Hello, here is a list of the interrupts of my BPi: root@bananapi:~# cat /proc/interrupts CPU0 CPU1 17: 0 0 GIC 29 Edge arch_timer 18: 1240001 514159 GIC 30 Edge arch_timer 21: 0 0 GIC 54 Level sun4i_timer0 22: 0 0 GIC 113 Level sun5i_timer0 26: 0 0 GIC 42 Level sun4i-spi 27: 14635330 0 GIC 64 Level sunxi-mmc 28: 0 0 GIC 71 Level ehci_hcd:usb1 29: 0 0 GIC 96 Level ohci_hcd:usb3 30: 755 0 GIC 88 Level 1c1…

Hi, can anybody tell me, why the rights on the serial port ttyS0 are R/W for the user (root), but only W for the group (tty) ??? crw--w---- 1 root tty 251, 0 Jan 24 19:45 /dev/ttyS0 Hardware is orangepi one, OS is Linux pi-one 3.4.113-sun8i #6 SMP PREEMPT Tue Jan 16 14:36:25 CET 2018 armv7l GNU/Linux I can change the rights with chmod, but the change is not permanent after a reboot. L.

I use Armbian_4.3_wheezy on SD video with 1280x720p resolution. When I transfer to NAND, only with the resolution of 1028x1024p and can not adjust the resolution to 1280x720p. Already changed the script.bin file (via fex2bin), the uEnv.txt file (disp.screen0_output_mode = EDID: 1280x720p60) and not worked. How can I change the resolution to 1280x720p? Best Regards Marco Aurelio

Hello ! I'm a proud owner of a Opi One which is supposed to be my media server and torrent server. I downloaded and installed Armbian, set it up, everything works great, but the only problem is video playing. I tried to run multiple videos and multiple formats (.mkv, .mp4) but the player remains black. If I go on youtube, the video plays but it's very laggy (like 10fps). What should I do ? Thank you ! Guess here is my answer, too: http://forum.armbian.com/index.php/topic/1129-h265/

i install armbian into banana pi M1 . cat .asoundrc-X pcm.!default { type hw card 2 } ctl.!default { type hw card 2 } and get sound from TV namely HDMI . then i attach HDMI cable to sharp TV . $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sunxicodec [sunxi-CODEC], device 0: M1 PCM [sunxi PCM] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sunxisndhdmi [sunxi-sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [sunxi HDMI PCM] Subdevices: 1/1 Subdevice #0: subdevice #0 ~$ cat .asoundrc pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } from sharp TV , i cannot get sound from TV, i get it only from audio out . i c…

Hello there. I am using ubuntu Xenial server on Banana pi. It has mysql, nginx, websites, and many programs and settings. I use it as a banana pi router. I used to use it as a server until now but now I got an hdmi to vga converter. Now I want to use Xfce. I installed xubuntu-desktop from the terminal. But the Xserver does not start because the GPU is not active. How do I activate the GPU without reinstalling? xorg err [ 14896.672] X.Org X Server 1.18.4 Release Date: 2016-07-19 [ 14896.673] X Protocol Version 11, Revision 0 [ 14896.673] Build Operating System: Linux 4.2.0-42-generic armv7l Ubuntu [ 14896.673] Current Operating System: Linux server2 4.8.4-sunxi #6 SMP …

Hi, I am new to nano-pi air neo. I am trying to get analog audio from the device. I had no success with the four connectors near to the camera connector. But if I connect the speaker to the DOUT of the audio, I get the sound but with lots of noises. How can I play audio in this device ? Am I missing something here ? Thank You.

Dear community, Im trying to get an USB gadget via OTG running on Linux (OrangePI Lite 2). As OPI Lite 2 doesn't support 'USB-UART/Gadget mode' like OPI Zero, I just modify the build config and rebuild kernel by myself as steps shown below. 1. I change the mode of USB from host to otg in the: https://github.com/armbian/build/blob/master/patch/kernel/sunxi-current/board-h6-orangepi-lite2-fix-missing-all.patch 2. I add MODULES_CURRENT="g_serial" & SERIALCON="ttyS0,ttyGS0" to build/config/boards/orangepilite2.conf file. 3. I rebuild the kernel and flashed the new image to sdcard. Unfortunately, I find it…

Someone has any experience changing the A20 to A20-H, our provider offers to us this new version, but I'm afraid to be software incompatible.

Hi all, I'm trying to use an Orange Pi PC Plus to drive an RS485 serial converter and ultimately talk Modbus to a sensor device. I have managed to get flow control enabled on the port, but the polarity of the RTS signal is active LOW, whereas the converter I have requires active HIGH. Is there any way to invert the polarity of the RTS pin for the UART? I think it can be done via ioctl call in C programs, but I need this applied at a system level to be compatible with some third party software. Thanks in advance!

HI, guys. i need help, with my orange pi zero + mpc2515. My connect, is the same as this image. Int connect to PA7. mcp-2515.dtbo: /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target-path = "/clocks"; __overlay__ { #address-cells = <1>; #size-cells = <1>; can0_osc_fixed: can0_osc_fixed { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequenc…

hardware: Orange Pi Zero H2 Kernel: 5.9.14-sunxi Armbian 20.11.3 Buster ethtool version 5.9 get error on cable-test option. full log: http://ix.io/2Icy sudo ethtool --cable-test eth0 netlink error: PHY driver does not support cable testing netlink error: Operation not supported