Allwinner sunxi

Hi , Igor! Will you release Desktop version on base of Vanilla? Thanks.

Im using armbian stretch on an Orange Pi Zero Plus. On normal boot up, the system hangs at starting version 232 for around 1-2 minutes. After this the system procedes to boot normally. What is this delay time and is there any way I can remove it?

I would like to upgarde my Cubietruck headless server from Legacy to Vanilla. With Legacy if I boot from NAND I can get my hard disc to spin down. But with SD card/sda root file system (as required by Vanilla) I can't get my disc to stop: if I issue 'hdparm -Y /dev/sda' it spins up again after a short interval. I have done everything I can think of to ensure that rsyslog is not writing to disc. Syslog shows frequent ata error messages that seem to coincide with the disc re-starting. Error msg: kernel: [ 104.477850] ata1.00: exception Emask 0x0 SAct 0x200 SErr 0x0 action 0x6 I have tried this on two different Cubieboards with different makes of hard…

Hi, I'm trying to install Armbian 5.20 vanilla kernel to eMMC on my Opi PC+. After nand-sata-install finishes I shutdown the Opi PC+ and power it back on. At least, I enable the power, I don't see anything happening in minicom on my pc. Only when powering it with a microsd in the slot (with armbian) will the uboot show in minicom on my pc. Doing a nand-sata-install with 5.14 legacy worked. What am I doing wrong (especially seeing nothing after a reboot with my ttl-to-usb connected is a bit strange for this noob)?

Hi, i am new here and like to say hello. On my new cubietruck I have one after another tried to install and use wheezy and jessie with legacy and vanilla kernels. With the legacy versions i failed because there seemed to be no video-output on VGA from the kernel. The boot-process seemed to be stopped after Starting Kernel. Then i found that it was visible on HDMI but not on VGA. Because I have only VGA-Screen on my desk i went on with vanilla jessie. But on the download-page there is the note "No audio or accelarated video". What does it mean in detail? I installed mplayer but in fact there is no sound at the jack. Isn't therefore any driver available? Which …

I have spent two days on LIRC. I am going to give up if no one can help me on this. My software conf are ARMBIAN 5.38 stable Ubuntu 16.04.3 LTS 4.14.18-sunxi and ARMBIAN 5.35 user-built Ubuntu 16.04.3 LTS 4.13.16-sunxi # cat /etc/lirc/hardware.conf # /etc/lirc/hardware.conf # #Chosen Remote Control REMOTE="None" REMOTE_MODULES="sunxi_cir" REMOTE_DRIVER="default" REMOTE_DEVICE="/dev/lirc0" REMOTE_SOCKET="" REMOTE_LIRCD_CONF="" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="None" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="audio_alsa" TRANSMITTER_DEVICE="hw@48000,r" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTE…

I'm not sure if this is off-topic, but I'd like to ask the forum about a problem. My goal is to run RPi-Cam-Web-Interface (http://elinux.org/RPi-Cam-Web-Interface). I have 5.20 Jessie server 3.4.112 that has been updated/upgraded on an Orange Pi One with a gc2035 cam on an expansion board from aliexpress. As a first step I got the cam working. There are some threads in this forum that made that easy. I then installed github.com/roberttidey/userland since it includes raspimjpeg - a key element in the RPi-Cam-Web-Interface toolchain. But when I run raspimjeg I get the error * failed to open vchiq instance Google has solutions that involve permissions…

Hi, Does anyone here is familiar using verified boot? Any one who already implemented in in any A20 boards? Thanks in advance.

Hi, I'm trying to use hardware acceleration on my OrangePi PC+ (H3) board, and when I try to compile v4l2-request, it complains for undefined constants. These constants are supposed to be declared in /usr/include/linux/videodev2.h, but looks like a very old version of this file is distributed in the latests Armbian images for my board. Some missing headers: V4L2_PIX_FMT_MPEG2_SLICE, V4L2_PIX_FMT_SUNXI_TILED_NV12 Looks like these #define have been introduced more than two years ago in the mainline kernel : https://github.com/torvalds/linux/blame/d5beb3140f91b1c8a3d41b14d729aefa4dcc58bc/include/uapi/linux/videodev2.h#L698 Even more weird: a later …

Hello I wrote aind compile little module only for tests: #include <linux/module.h> #include <linux/sched.h> static int errval = 0; //module_param(errval,int,S_IRWXU); module_param(errval,int,S_IWUSR|S_IRUSR|S_IWGRP|S_IRGRP); MODULE_PARM_DESC(errval,"Value to return from init function"); int my_init_module(void) { printk("errval=%d\n",errval); return errval; } void my_cleanup_module(void) { printk("The module is now unloaded\n"); } module_init(my_init_module); module_exit(my_cleanup_module); MODULE_LICENSE("GPL"); compile by: make -C /lib/modules/6.6.75-current-sunxi64/build M=$(PWD) modules And it cause segmentation fault only…

Hello, today I want to connect the OpiPcPlus to a Flexscan S1921 Monitor. I select h3disp -m 33 -d to use my *tested* hdmi-to-dvi cable and reboot. Now the monitor complains: fV: 59.9 Hz fH: 63.9 kHz fD: 161.7 MHz ****red*** this seems too high because VESA mode should use a pixel frequency of 108MHz which is also the spec of the monitor. 1280x1024 @ 60Hz (VESA) hsync: 64.0kHz 1280x1024 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync The pixel frequency seems too high for the 60 Hz image refresh, it corresponds to 85 Hz. I am using legacy kernel: Linux JagOpi 3.4.113-sun8i #10 SMP PREEMP…

Hi, after I made a software-update for my Cubitruck last week, my VGA monitor shows text only up to "starting kernel", then turns black. HDMI still works. I tried to reinstall the newest versions of both Ubuntu Bionic and Debian Stretch, both show this problem. The old VGA monitor is used only for maintenance work on my home server and off most of the time, it would be a shame if I had to buy a new HDMI monitor for this purpose. What is going on? Thanks Engelbert

I have been experimenting with trying to get video acceleration working on the A83T. I can see from /proc/device-tree/soc/... that there is already a video-engine node within the current A83T device tree. It appears to be applied as one of the megous patches ARM-dts-sun8i-a83t-Add-cedrus-video-codec-support-to-A83T-untes.patch. Admittedly this is noted as being untested. In my initially created build via the build framework, Cedrus was not present at all among the list of loaded modules. I addressed this by creating an entry in the Cedrus compatibility table for the sun8i-a83t-video engine drv-sun8i-a83t-cedrus-add-variant.patch It now appears to l…

Has anyone managed to get video encoder working with the latest mainline kernel? I'm getting stuck trying to compile the cedar_ve kernel driver from https://github.com/uboborov/sunxi-cedar-mainline I have downloaded the kernel source using armbian-config and then built the sunxi-cedar-mainline kernel driver. However, I fail to load the driver due to version magic: When trying to force the load: But no dmesg message about magic check failure.

Hello! i'm new user in linux, and i have one problem with my display on chinese tablet. I install armbian img from Olimex Teres A64 img. Armbian is started but not work the display. How is the possibility to change or set video output for display? the file script.bin i don't find. Thanks alot for response.

The Orange Pi Zero Plus has only a CVBS/FBAS/RCA video output, therefore I believe that only a televison but no VGA or DVI/HDMI monitor can be used (or headless use). Has anybody an idea how to convert CVBS to VGA or DVI/HDMI? L.

hi when i try to play a video player performance is very low on armbian but when i install android on my board video player performance is good Enoughwith mx player app i try improve performance with overclock cpu but its not helpful how can i improve performance of video player on armbian ? and its possible to play h.265 video and 3d video?

Is there any way to get a video player to display subtitles on an H3 board? I've tried VLC and SMPlayer, but neither are able to do so (the problem seems to be that the video output is overlayed *over* the system display rather than mixed with it on a per-pixel basis, so while the subtitles are being displayed by the player, they simply aren't visible). Is there any adjustment/update/other player I can use to fix this problem? Orange Pi Plus 2 I have armbian 5.05 installed, so not sure if there are any updates that might help?

Hello guys, I am having problems with vlc, the video is running out of proportion and it is all over the interface, ie, even minimizing vlc the video is still being shown, I tried to change the codecs but I did not have a satisfactory result, because only the VDPAU works without lags Help me please, sorry for bad English.

Hey kids, it is me, again! So, this time I found out (well, you maybe knew it before and I am dumbing around again) that voltage control does not work on Banana Pi (at least) mainline kernel. Well, if I am supposed to change it in linux-mainline/arch/arm/boot/dts/sun7i-a20.dtsi. I tried to reach 1248000kHz, which is, of course, unstable. So I was adding and adding voltage, until I was too afraid to continue (1650000mV ). But BananaPi was unstable the same way (freez after few minutes of FTP transfer), no more (bad charger) or no less (would still need more voltage). So after few hours of re-compiling source and listening wonderful music I tried this: 1248000(kHz)…

Hi, I used to run a RPi3 as a VPN and DNS-Server (PiHole) and it worked like a charm. Since the RPI3 is a bit oversized for this work I bought a NanoPi Neo 512MB and installed armbian Ubuntu 4.9.x, but I have some issues with it: - eth0 is only connected by 100/half duplex. I can set it manually to full duplex with autoneg off, but after a few secondes it falls back to 10(!) half duplex. with autoneg on it comes back to 100 half duplex (the amber led is off; cable and switch are ok) - the MAC-Adress is changing every reboot. I have to fix it manually - I can set up Pihole to use the Nanopi as a DNS-Server and it works well in the LAN, until I connect over openVP…

I want to wake up my orange pi plus 2e device through the pin. It will feature a PIR sensor on this pin. I did research in the forum, but I could not find any documents. We can wake up by applying a interrupt like Arduino through a pin. How do I follow a path for this device? When I take the device to sleep, I can not wake it up again. The buttons on it do not function at all.

First off, I'd like to thank the maintainers for all the work you've put into Armbian. It's really been a pleasure to use. I'm currently using an OrangePI 2+as a kiosk computer, and I'm wondering if there might be some other way to wake it from sleep other than pressing the power button. Would it be possible for it to wake from sleep if one of the GPIO pins were pulled high, for instance? TIA, -Jim

Hi, I have found a problem when I reboot my NanoPi Neo, related to WiFi + BL device which is plugged in USB 2.0 port. The WiFi device is a Realtek 8821cu and system loads driver correctly when I do a cold boot or if I hot-plug it, but it fails in a warm boot. After doing many tests, I realized that if I plug the WiFI dongle in a non-powered USB 2.0 hub and I connect this latter to the NanoPi Neo's USB 2.0 port, then it also works. I don't have anymore idea to solve it. The 8821cu driver fails because WiFi device shows itself like powered down.

I'm not sure if this is a bug that needs to be reported and I don't know what issues it may be causing, if any. ----< CUT >---- Sep 16 08:55:56 loki kernel: [35972.411737] ieee80211 phy2: brcmf_fweh_event_worker: event handler failed (72) Sep 16 08:55:56 loki kernel: [35972.465736] ieee80211 phy2: brcmf_fweh_call_event_handler: no interface object Sep 16 08:55:56 loki kernel: [35972.465781] ieee80211 phy2: brcmf_fweh_event_worker: event handler failed (72) Sep 16 08:55:56 loki kernel: [35972.471791] ieee80211 phy2: brcmf_fweh_call_event_handler: no interface object Sep 16 08:55:56 loki kernel: [35972.471838] ieee80211 phy2: brcmf_fweh_event_worker: eve…

I just run an "sudo apt upgrade" and my 22.05 system was upgraded to 23.8.1 As a result WiFi stopped working. The wireless interface disappeared and can not be configured with armbian-config. On the positive side it seems like the load bug is now fixed, load can now be 0.0.0 at its lowest as opposed to 1.1.1 before. is there a way to revert back to the old kernel with Armbian?

Dear maintainers, I have my sensors configured to reboot every night via a user cronjob (0 0 * * * /sbin/reboot), 14 sensors do this without a problem. I've fixed the nanopi neo+2 reboot from NAND some months ago (by re-using friendlyarm first stage u-boot). I just stumbled upon a failed reboot with one of my nanopi neo+2 nodes, after two successful reboots. Looking at the /var/log.hdd/syslog, it got stuck in the shutdown procedure when the watchdog reported a failure. The /var/log.hdd/syslog.1 extracts below show the start of the watchdog, and the stop of the watchdog and its failure. After the failure the system doesn't come up anymore, it needed a pow…

Hello all. Okay: I am a total newbie to Orange Pi. I apologize upfront for any and all obvious self inflicted mistakes that you all spot. AGAIN: total newbie to the Orange Pi world. Please go easy in me! I have an Orange Pi Win Plus A64 board and frankly --- I love the darn thing! Powerful for my needs and I have a niche application that I am working on and this board is really the only one that fits my needs. The 2GB RAM is a must. The issue I am having is this: I am usinga waveshare 10.1 inch TFT HDMI display that has the SPI connector (lcd: https://www.waveshare.com/wiki/10.1inch_HDMI_LCD). I have att…

I bought a 7inch HDMI LCD (C) panel http://www.waveshare.com/7inch-HDMI-LCD-C.htm and trying to use it with Orange Pi One. All is right, but: 1. the image constantly flickers 2. when the brightness changes, a "ghost" of the old image appears I use power from PC power supply, yellow line, armbian image is Armbian_5.30_Orangepione_Ubuntu_xenial_default_3.4.113_desktop Can I do something with my configs, or this panel is a piece of shit? My fex: [boot_disp] advert_disp = 0 auto_hpd = 1 output_type = 4 hdmi_channel = 0 hdmi_mode = 4 cvbs_channel = 1 cvbs_mode = 11 output_full = 1 hdmi_mode_check = 1 screen0_out_c…

Hello, I've got two WaveShare HDMI LCDs: 7inch HDMI LCD (C), 1024x600 10.1inch HDMI LCD (B), 1280x800 Has anybody managed to configure them for the Banana (with Armbian legacy kernel)? The company WaveShare provides a Raspbian image that works okay (screen and touch). I used fbset to figure out the current settings while running the provided Raspbian image: 7inch: mode "1024x600-43" # D: 32.000 MHz, H: 27.778 kHz, V: 43.066 Hz geometry 1024 600 1024 1200 32 timings 31250 40 40 29 13 48 3 rgba 8/16,8/8,8/0,8/24 endmode 10inch: …

I've installed Armbian_5.14_Orangepiplus_Debian_jessie_3.4.112_desktop on a ORANGE PI PLUS 2 H3 QUAD CORE 1,6Gz / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) _ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | |_| |_ | |_| | | | (_| | | | | (_| | __/ | __/| |_ _| \___/|_| \__,_|_| |_|\__, |\___| |_| |_| |_| |___/ Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i System load: 0.52 Up time: 1 min Memory usage: 14 % of 2013Mb CPU temp: 59°C Usage of /: 19% of 15G then installed lightdm and running the xfce4 desktop with HDMI monitor of 1920x1080 I can't…

Hello everyone, I am kinda of new to the orange, I think it's fantastic, I worked with rasp for while and I think the orange just slashes it. Pampering the orange aside, I am trying to hook up an old webcam to the Orange pi lite and I running into some issue, my lsusb info is this: Bus 003 Device 002: ID 1e4e:0100 Cubeternet WebCam When I start motion, everything works fine, although when I go on the browser a gray screen comes up saying: unable to open video device I have changed the configuration file of /etc/motion/motion.conf and /etc/default/motion as instructed here: http://www.orangepi.org/Docs/Webcams.html Plus I have changed the with my i…

Hello I was build image for my orange pi pc2 devices: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.46 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=custom BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image I was faced with strange thing: After burning another image and lunch it on the device - on the first (and every) boot I see "first start panel window". And when I do formatting this SD card, and burning again - everything alright (first start panel window dose not appear) I have been already burn 10 SD cards with same image and met th…

Hello to all I am using Debian Jessie 5.25 on OPi PC+. And using rpi-monitor for monitoring stuff. I already made a fully working webserver and moved my wordpress to it, CPU usage around 10-20% when taking traffic, so it works like a charm. Today i decided i will use it to download a few big files with wget command. At first i was trying to be smart and save it directly to an ntfs pendrive mounted at usb0. Result - 40% I/O wait CPU usage and limited transfer (maybe 20-30 KB/s). Yes, my pendrive is bad, but hey, not so much. So i cancelled wget and tried to download the same file into /var/ into my SD card (used as system disk). Well, transfer was ok (200kB/s ser…

I have an Orange Pi Zero that had an uptime of well over a year monitoring the output of some solar panels and the state of charge of a battery. It then switches a couple of relays in response to these measurements. It has been really reliable for 2 years, never crashing or rebooting until now. At the beginning of September it started to stop working, it has no monitor or keyboard, only a cat5 cable, so when I say stop working, I mean it stops logging to the nfs drive, stops switching the relays, stops responding to pings and any ssh sessions timeout. It does this every few days, around 6:30 am, and I then have to power cycle it to get it to work a…

Hi everyone, I'm trying to set up transmission daemon + some webserver who can play some video or let smart tv watching some video or listening music, any idea? Thank you very much

Hi! The jessy vanilla image works fine, but when I boot the Olinuxino Micro with a SATA HDD connected, I don't have ethernet/ssh access anymore. Even reboot _without_ the HDD doesn't work, I need to restore the content of /boot with an SD-card-reader to make it work again. Sorry, I am (yet) not really into sunxi/uboot/kernel topics, so maybe there's a simple explanation to this behaviour?

I would like to test or reinstall my nanopi air, but I can only find download for "neo core / air" "testing version" with mainline kernel. In fact I was looking for an uptodate uboot/kernel for legacy kernel or a "usable" version with mainline - that is for me - with an asix module and working WIFI / BT.

Dear Forum, First of all thank you for being a member here. Second is that I would need some help on selecting an image for my present CT board. I need the followings: 1. hostapd with dnsmasq 2. g_mass_storage 3. sata 4.spidev or equivalent Preferably: 3. I would need free up SD card slot, so nand or SATA boot would be preferred. Which image is the best for me even if I need to recompile it? Thank you in advance.

I'm not sure I even want BakeBit. I'm trying to use the GPIO in my NanoPi Neo2. Specifically I want to read a digital I/O pin on/off state. And if possible I'd like to read an analog voltage from the H5's built in ADC. Now that I've looked deeper into BakeBit, it seems like the entire purpose of BakeBit is to do GPIO with an Arduino, and read the information remotely on a RbPi/NanoPi or whatever ON the Arduino's GPIO pins. If that is really what BakeBit is, then BakeBit doesn't interest me. The H5 already has GPIO and an ADC. We just need to get that working. For interest's sake, here is the progress I made with BakeBit. ADC Python example in Bakebit h…

Please give me a tip - what is purpose of /dev/mmcblk2boot block devices created? Quite small size - 4MB - ones, do they serve to something u-boot needs at boot time? There are no records for them in fstab so I assume they are created by zram, but what happens to them after boot when they aren't needed anymore? Board Orangepi 3LTS with bookworm minimal Also as a matter of wondering - why there are two zram devices: one of 1/2 of RAM (as usual) and another of quite small 50MB only, what is it for? root@heaven:~# fdisk -l <redacted> Disk /dev/mmcblk2boot0: 4 MiB, 4194304 bytes, 8192 sectors Units: sectors of 1 * 512 = 512 byt…

Hi Im seeking for a kernel that i can trust it does not hang. Using the old 3.4 kernel on bananian I could get my banana pi m1 more than 6 months without hangs and reboot. Now im been playing with the armbian and 4.x kernels for almost an year, and the banana pi hardly got 2 months without hangs and reboot. Could you be kind to tell me what is the kernel version with longest uptime with armbian on a banana pi? Sergio

After along time I downloaded a new armbian image, after doing apt update/upgrade for the last year or so. I was quite surprised to see that the pcduino3nano is now deprecated, while other A20 boards are still supported. What was the exact reason that the pcduino3nano was dropped from support? If I keep using the deprecated OS, can I fully use apt update/upgrade for all user stuff? What would happen to all kernel and u-boot update packages? Is the latest armbian for the pcduino3nano automatically disabling those updates, or do I need to do something manually? *should* I block kernel & u-boot updates? thanks, Michale Jasson

Hi everyone. I heard Armbian was the to-go distribution for the Nanopi NEO Air. I've got a bunch of these boards where I'd like to use the built-in Bluetooth and Wi-Fi capability in a small form factor for a project. I don't need video or audio or other functionality. I see a legacy kernel "stable build" and a mainline kernel "experimental" build. For the experimental build it lists the following known problems: No Mali drivers No hardware accelerated video decoding schedutil CPU governor may cause clicks and pops on audio output – change(d) to ondemand to work around this issue This sounds fine with me. I need no video, and…

until I've installed the 24.05 image the cubieboard2 came up with an HDMI output on video, I have an DVI to VGA Adapter connected and could use an USB Keyboard+Mouse and the VGA Monitor. Since I've installed the Armbian_community_24.5.0-trunk.667_Cubieboard2_jammy_current_6.6.31_xfce_desktop.img.xz on the SD card, the system comes up with an ASCII Console on the VGA Monitor, later the screen gets cleared with only an cursor in the left top and then gets switched off. I've managed before to switch the output of the X-Server from None-1 to HDMI-1-1 using xrandr, but this is only possible with an proper and authenticated Display and I have to use an autolog…

I wanted to try 3.4 to see if I could build FFmpeg with the legacy Kernel. When I run any of the three (Trusty, Jessie, Wheezy) as soon as the script says starting Kernel, I get a few blue and green noise lines on the screen and then the screen disappears. I can use SSH and.the system is booting up and running. The one thing that I noticed is that when I log on, the name of the machine is LIME instead of MICRO. I'm running an Olimex Olinuxino Micro. Is there a config file that I need to tweek, or is the Kernel setup for a LIME? thanks MikeC

Hello all, i can't see Banana Pi M1 on the available downloads on Armbian site where can i find it? if that exists of couse. Thanks

Hello! I'm trying to make image for olinuxino lime A10. Prebuild image does not have /dev/uinput and /dev/hidraw for my touchscreen, and built without CONFIG_DRM_KMS_HELPER, so i can't replace broken EDID for my HDMI display. A month ago i succesfully build ubuntu image with uinput and hidraw support. But now - i need to rebuild it again, but kernel compilation fails with this error: LD drivers/media/usb/built-in.o LD drivers/media/built-in.o make: *** [drivers] Error 2 [ error ] Kernel was not built [ @host ] And I don't know where to find error description. The last error was missing libssl-dev. Regards.

Hi, i need to download version Armbian 21.05.6 Buster with Linux 5.10.43-sunxi , is it possible to do it now and how? thank you

Hi all, I'm new about u-boot and arm device. I was learning how to build u-boot for banana pi m2+. Where I can get working u-boot defconfig for that device? Thanks

Sorry if I miss something, but it seems debian is no more available for download on this page https://www.armbian.com/orange-pi-zero/ Do you have any information please?

Hi all, everytime I turn on my Nano Pi it will sync the clock using NTP. When network is not enabled it will rewind the time to something that I still can't comprehend. I found lots of topics about people talking about how to add a RTC to the system, but none talking about the current RTC that is recognized by the kernel. Currently when the system is powered off and on (10 seconds distance) without network the time will rewind between 5 and 15 minutes. I understand that this happens because there is no RTC to write the current clock and battery to keep it. But there is obviously a RTC somewhere because removing power from the device and putting it back will keep a wrong b…

I want to use an ADAU1979 with an olimex A20-Micro. Needs to show up as a device in ALSA, alongside the in- built CODEC - As far as I can see, this driver is in mainline kernel but I have no idea how to configure the kernel build to include it. Obviously we need to tell the system where its i2s/SPI interface is connected etc. Unsure which kernel version (legacy or mainline) to begin with. We do need a desktop environment and the olimex 10"/7" LCD to work also... I am starting this from a position not having built a kernel or kernel modules before so If this idea is a non-starter, someone please tell me so. Thanks.

Hi, I have been looking to download "Armbian_5.52_Olinuxino-a20_Debian_stretch_next_4.17.19.img". Torrent that I have is not seed, it been stuck for all day. Can anyone please provide me with downloadable link or please seed the torrent? Thank you Jedi

Hello all, Where can I find the latest (and greatest?) version or Armbian. I think it is at the moment v5.24 . I looked at http://www.armbian.com/download/ and http://image.armbian.com/ . But no luck...? Is there another location? Or do I need to build from source? Thanks!

Are the old releases of Armbian available anywhere? I can't find them.

Took me over a year to isolate this bug. Randomly, I have found that /boot/armbianEnv.txt had unconsistent content. Examples: .tty1tty1LOGIN.8 ¹[fU7ttyS0tyS0LOGINusbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="Demaine_40_Grd_Rue_Chambre-BP" #psk="1234567890" psk=693d195a3bf2ab6defbcc0b54604ced4286a067996138db6dc793d8648f67d79 } usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="fabste" #psk="1234567890" psk=95342031a4b28398045e1761f9c64f8454902e80d37102e5476fa…

Hello, in Armbian TCP buffers are already set. I can change them by putting new values to /etc/sysctl.conf. But, is this elegant? Or would it be better to change directly the values from armbian? In which file configures Armbian the TCP buffers? Thanks a lot and best regards, Michael

Hi: I am confused. The current armbian for cubietruck is still:Armbian_5.20_Cubietruck_Debian_jessie_3.4.112_desktop-2.7z but on the download page it states that version 5.23 is the latest version. What should I do to get the latest version? (as of today Nov. 13,2016

On the download page images have kernel 4.18-rc7 I need headers for this kernel. How to find which commit is these images are built from?

Hello, Did someone found BT dongle working with OrangePi Lite? I would like use it to send files to other BT device. Is this possible with this model of OrangePi?

I've been trying to change the I2C clock frequency on a NanoPi Duo doing the following: cd /boot/dtb sudo cp sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dtb.old sudo dtc -I dtb -O dts -o sun8i-h2-plus-nanopi-duo.dts sun8i-h2-plus-nanopi-duo.dtb sudo nano sun8i-h2-plus-nanopi-duo.dts in i2c@01f02400 section change clock-frequency = <0x186a0> to clock-frequency = <0x30d40> (200 KHz) sudo dtc -I dts -O dtb -o sun8i-h2-plus-nanopi-duo.dtb sun8i-h2-plus-nanopi-duo.dts reboot Looking in armbianEnv.txt I have overlay_prefix=sun8i-h3 and cat /proc/device-tree/model shows FriendlyARM NanoPi DUO. The issue is that no mat…

Hello, With a bananapi pro, which legacy image is better to use ? ubuntu xenial or debian jessie ? I intend to use it mainly as a server and occasionally to watch movie on a hdmi screen. I do not want to install a full desktop, I prefer to log through ssh and launch an X server remotely. Also, I need an mpv (mplayer) with acceleration enabled. thanks for your help Regards

hey, it is nearly everything said in the title. I want to use my cubietruck for playing streamed videos on my beamer. I don'T want to take my pc to the living room everytime i want to watch tv on my beamer, so i hope, there is a way to get the cubietruck working with vlc mediaplayer. Any tipps?

I'm on a years old Orange pi zero H2, an often forgotten single purpose print/scan server board. So i want to upgrade to the latest kernel via armbian-config->system->other(switch kernel). Previously its on 4.19. so when i tried to change to current 5.8.16, 5.8.14, 5.8.12 & 5.8.5, i got "No end-user support: unsupported (stretch) userspace!" it has taken me an hours plus just switching kernel, hoping to find the supported ones. though i dont mind unsupported / legacy kernel, i still prefer the latest supported ones. Is any of the kernel on the list supported? if there none on the list, is there a way to add a supported kernel?…

I'm on 'cat /etc/os-release|grep ARMBIAN_PRETTY_NAME' = ARMBIAN_PRETTY_NAME="Armbian 24.11.1 bullseye"

Hi After reading this: "No audio driver, IR, NAND, BT, HW video, I2C and SPI untested on 4.0 or higher​" i'm not sure which kernel version should i choose. Is that "no audio driver" means that there is no HDMI audio, or no any audio including jack audio? Both kernels support the "Allwinner Security System cryptographic accelerator"? As i'm using CB2 as a headless java application server, samba fileserver, dlna server and music player daemon server, i need only jack audio from these, and of course the hw cryptographic support.

Greetz // Pozdrav vsem uporabnikom vsezmagovalcev! I am planning to use my Cubietruck for a general-purpose desktop computer to surf the internet, write documents, watch movies (youtube, VLC, lan/dlna), etc. Basically I'd like to install a lightweight desktop image on it and connect it to my SmartTV in the living room via a short HDMI cable. I'll probably need video acceleration for a 1080p resolution. Thing is I'm currently in a bit of a dilemma because there are so many premade images out there, and most of them seem outdated. Can you recommend me which image to use for my goal (possibly a LTS release)? I've been leaning towards Lubuntu, but I see debian has som…

Hi, Got Debian (8) legacy 3.4.113 server/console and would like to setup a WiFi hotspot. (latest Armbian build 5.51) Seen two methods in Armbian docs 1. -> https://docs.armbian.com/User-Guide_Advanced-Features/#how-to-set-wireless-access-point and via armbian_config in https://docs.armbian.com/User-Guide_Armbian-Config/ 2. -> https://www.youtube.com/watch?v=__BJtInOQFY So I'm a bit buffled about it. Got some questions Got a RTL8188CUS is it suported nowadays? or should I get a specific other one? Do I need to have internet/ethernet/lan connection active during the hotspot creation via armbian_c…

I hear that Orange Pi 2E has 1GB network speed and an USB3 port. In my project I paln to use an SBC as a network bridge and sniff traffic for problems. A simple network tap would otherwise be ok but they come only with 10/100Mbd speed limit. What I'd do have two ethernet ports on the Orange Pi, one regular and one via USB3. No to my question: are Orange Pi capable for this or is the advertised network/USB3 speed buggy/lacking? I have one Orange Pi PC for a file server and it has been running for weeks just fine. Raspberry Pi's are fine to (albeit still no 1GB ethernet). Raspberry Zero's have issues (mine seem to lock up after a couple of days).

Hello, In a GOLANG based, RPi 3B+ project I am using the https://github.com/stianeikeland/go-rpio package to read the state of the GPIO-s. I am planning to set up some Banana Pi M2 Berries with the same software. The package - as it was expected - doesn't work with the M2 Berry. I could adapt the package for the Berry, but I don't know which peripheral chip is used in it. Does anyone know which peripheral chip is used in the Berry? (The schematic diagram on BPI's page is useless). Thanks, G.

I have a NanoPi Neo Core and I'd like to analyse the SPI controller driver and why it toggles the lines the way it does. In the overlay file, all I see are mentions to 'spidev'. Where can I find out why the data lines shown below toggle the way they do? I.e. chip select goes low way before the clock line. The MISO line has a droop to GND briefly and the CLK line hangs high for a while before toggling... Thanks forum :). YELLOW: CS PURPLE: MOSI BLUE: MISO GREEN: CLK EDIT: I'm sending two bytes, 0xDA, 0x00 at spi mode 3. Ignore the decoder, it was set to read LSB first.

hi, i have burn the jessi server with my orangepi one from http://www.armbian.com/orange-pi-one/. all run well, but when i try to use the arm-linux-gnueabihf-gcc within ubuntu 14.04 to compile a helloworld into this board. I meet segmentation fault. does any one known which toolchain should I use when I want to cross compile program for it?

I have an Orange Pi PC Plus and I'm looking for a USB video grabber. Could you suggest me some models which are easy to setup and work with OPi reliably?

Hi, I am new to Orange Pi ecosystem. I have a Orange Pi PC 2 running armbian and some times raspbian. I want to use a wifi adapter to this. Since there has been many discussions on which adapter to chose and how to chose I am really confused. Please help me select a wifi adapter which could be installed easily considering that I am a rookie.

Hi, I just installed ARMBian on my Banana Pi M2+ (BPi-M2+) and think to do the same on my router Banana Pi R1 (BPi-R1). As the WiringPi is created for GPIOs from Raspberry Pi, I presume there are perhaps not the same on those Banana Pi boards. But I discovered there are many Wiring libraries for this GPIO use on the BPi. Does somebody give back its knowledge to know which Wiring library is the best for those two Banana Pi boards ? - WiringBP - WiringOP - MikuPi I want to use them for reading Temperature and Humidity (DHT22) and a sonar sensor (HC-SR04). And further with a NFC rader. Sincerely thanks for your help.

I'm having trouble porting some WiringPi programs to my NanoPi Neo. I have an original neo v1.0 running the latest armbian stretch (as of Oct 04 2018). Have tried several, including mstroh76/WiringNP, and can compile, but programs hang when executed. I'm okay if this is the deep-end of the pool but I wanted to verify that I an indeed in deep waters or if I'm doing something dumb and really in the shallow waters and all I have to do is stand up to get my head out of the water. Which WiringPi library should I be using for C language programs on a NanoPi NEO v1.0 running a recent Armbina Stretch release?

Who can share their valid /etc/apt/sources.list for an armhf SBC? Some past update has messed mine up a bit. Mine is: # deb http://gb.archive.ubuntu.com/ubuntu/ jammy main universe restricted multiverse deb [arch=armhf] http://ports.ubuntu.com/ubuntu-ports/ jammy main universe restricted multiverse # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. # deb http://archive.ubuntu.com/ubuntu/ jammy main restricted # deb-src http://archive.ubuntu.com/ubuntu/ jammy main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb [arch=armhf] http:…

Hi My Orange Pi PC shows 21.08.5 armbian version in /etc/os-release and /etc/armbian-release but 21.08.2 with uname -v Why don't match the versions ? Thanks

Hello, please tell me why Chromium does not work on Orange Pi Prime? Здравствуйте, подскажите пожалуйста, почему не работает Chromium на Orange Pi Prime?

I made tests with Orange Pi 2+ to install Armbian to eMMC. But I have no idea why it takes 30 minutes to install. I assume write speed of eMMC to be 5MB/s (ok maybe it is even faster) and Armbian on SD card is about 2.1GB, so it should take ~7 minutes to copy files, plus some more minutes to finish final touches, let's say 15 minutes together. But why it takes more than 30 minutes? Is there any possibility how to reduce this time? P.S. When I am burning armbian img to SD card, in 5 minutes I am ready to go and boot the system.

Hi, What do you do to avoid the problem with zero size files or zeroes at the end after unclean reboot on cubie or another device with nand flash on extx filesystem ? Why do everyone use extx filesystems when its generate these problems ? a little description ... http://www.linux-mtd.infradead.org/faq/ubifs.html#L_empty_file http://www.linux-mtd.infradead.org/faq/ubifs.html#L_end_hole Thanks, ariz

Hi, I have "orange pi 3" and I want to migrate "Debian Buster" from "SD" card to eMMC. I run this command sudo nand-sata-install And I only get this! see link https://ibb.co/wQz0jx4 As you can see there is no item "Boot from eMMC - system on eMMC" What am I doing wrong? PS - Armbian Buster downloaded from https://www.armbian.com/orange-pi-3/

Hi everyone. I have a opz with H2+ and expansión board. I had installed Jessie before. And now, I upgraded to stretch. why espeak-ng sounds so bad?? in jessie that did not happen.

I must have missed the discussion about not having a desktop version for this board. Does anybody know why this option is not available? Now that I finally have the Bluetooth working, I can use it as a proper desktop. I have "simulated" a desktop build by following the Armbian build script... installing all the packages for xfce4, but it lacks some functionality (namely the notification icons). It would be really nice to have a proper Armbian desktop on this board. Thanks.

I have Orange Pi Plus 2 running Ubuntu Bionic with Armbian Linux 4.19.62-sunxi and I would like to upgrade it to recent Armbian build based on Ubuntu Linux Server and move OS to SSD connected to one of USB ports. I tried to use Armbian_22.08.2_Orangepiplus_jammy_current_5.15.69.img.xz but it does not connect to both HDMI and network. I tried unofficial command line interface images from product page and weekly released unsupported community builds. Behavior of all these builds is the same - no output to HDMI, no network connection. Finaly I found that recent image for Orange Pi Plus / Plus 2 which boots is Armbian_22.08.1_Orangepiplus_jammy_current_5.15.63.img.xz.…

I have orange pi one with Armbian Xenial desktop legacy kernel 3.4.y which have a script.bin file in /boot directory and doesn't have /boot/dtb directory ...but when i installed Armbian Bionic mainline based kernel 4.19.y, I found the .dtb files but not the script.bin ....now i don't know how to configure both touch screen and the pwm pin! is the .dtb file (sun8i-h3-orangepi-one.dtb) is the same as script.bin or orangepione.bin ? if so, how to configure it? because i am used to convert the script.bin to .fex to configure it and then back to .bin.

Hello everyone, newbie here just starting with armbian Recently I bought a cheap orange pi zero and I cannot connect via ssh through wifi. I read multiple threads regarding that issue however I cant say I understood everything I read. So, in a nutshell, is there any solution available? As many users reported, I can connect via ssh over etherner or wifi when ethernet is plugged in but not when only a wifi connection is available.

Good evening. I've just installed Armbian in a OPI +2, in a 32 Gb card. The OPI is connected by LAN to my router, in the same way the PC I am using to write this message is. But "Wicd Entwork Manager" says : - "not connected" after "Obtaining IP address" if using wire-default profile. - "done connecting" after "setting IP address " id using a fix IP address setting profile, but in fact, there is no connection. Has anybody faced something like this ? Any idea ? Best regards. maesstrissimo

Hi, I'm still experimenting with different "Linuxes" on that boards.. to get an LCD Display (LVDS) and the Ethernet part working. It cost me days to figure out that there seems to be an ugly glitch. with the stone age "cb2-dvk-sdcard-lubuntu-lcd v1.0.img" I get an working X11 Desktop with 800x480 ..but Ethernet doesn't work. I've checked those fex files (script.bin, script.fex) but couldn't figure out what's going on. I think that doesn't interest someone besides me, ok., got that. Now I've tried the actual "Armbian_community 24.5.0-trunk.667 Jammy with Linux 6.6.31-current-sunxi" that I've downloaded from somewhere here (…

hello guys ! I have a big problem which I'm not able to solve . It makes me crazy .... I have an orange pi plus 2 and I have changed the antenna , more powerfull. I'm new with linux and armbian . At the moment I can connect my orange to my router via lan cable and connect it over internet to update and upgrade Armbian and else. Using graphical wicd I can connect it to my home wifi network after put the psw .In this case orange pi is a client. Pratically the wifi on board is working , I mean , because it scans and it lists all of the wifi network reacheables around . But my target is to create an access point with my orange pi . After some weeks I'm watching seve…

Hi, I've now spent days to get the access point running with hostapd and dnsmasq on the OrangePi Lite. Still without success. Output of hostapd: /etc/hotapd.conf: /etc/network/interfaces Output of iw list: /etc/init.d/hostapd: The strange thing is, that in rare cases it was sometimes possible to create the AP with the same configuration after doing: But on reboot it always failed. Can somebody help me please?

terminal command to connect 1)wifi (using username and password). 2)hotspot os i am using is Armbian_5.65_Nanopiduo_Debian_stretch_next_4.14.78.

Hello guys. I try to configure AP on WiFi. I have created /etc/hostapd/hostapd.conf: interface=wlan0 driver=nl80211 country_code=IN ssid=TEST hw_mode=g channel=6 wpa=2 wpa_passphrase=12345678 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=0 Then I have uncommented DAEMON_CONF="/etc/hostapd/hostapd.conf" in /etc/default/hostapd. After it, I run /etc/init.d/hostapd restart And I try to scan WiFi via mobile phone, and no TEST. What am I doing wrong?

I recently updated the OS (apt-get dist-upgrade), for one of my test systems, and subsequent to this Kismet has stopped working with the wlan0 interface. Everything was working properly before this update. I see it (and wlan0mon) showing Promiscuous mode in the output of iwconfig. I'm not really a Linux person, so any pointers on how I can diagnose/repair?

hi, I made a program on Orange pi minus (kernel 3.X)using wpa_supplicant for wifi direct. That worked fine (basically). But i have been asked to do it on Orange pi plus with Kernel 4.9. The wifi works when i using nmtui, but when i made a iw list i couldn't find my material and i am not able to configure P2P. I think the problem is the kernel version and not the Hardware because my card with kernel 3.X works on orange pi pc plus. So i am a bit lost, what can i do ? My guest is to modify the realtek module ? I am not sure if i am on the right direction... Thanks, Ps: Sorry for my english.

Hi. I configured OrangePi zero with the NAS interface and with Openmediavault. I also configured ethernet card and wifi. Everything works. But if I disconnect the network cable, I also disconnect the wifi. Now I would like the wifi to work even without ethernet cable. This is possible? Many thanks ps. this the version of software ARMBIAN 5.31 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i

hello please help to install and configure wifi usb edup ep n8553 on OPI pc dongle unrecognised and no working drivers. riz

Hello everyone! I'm newbie with arm boards and i have Cubieboad A20(2012). I'm running on ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun7i and i have inssue than i can solve. tryin to load driver ath9k_htc for my usb dongle TLWN722N works with , but it don't do. Instructions to run script root@cubieboard2:/home/gui/Downloads/GitTPLINK/tlwn722n-linux-install# ./install.sh Installing firware... Changing to directory "compat-drivers-source"... Trying to select the ath9k_htc diver to be compiled... Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile…

at OPI PC with kernel Linux orangepipc 3.4.112-sun8i #30 SMP PREEMPT Sat Apr 30 19:49:10 CEST 2016 armv7l GNU/Linux before the last kernel update we use rt2800 wifi dongle. dmesg | grep usb - shows this output: [ 0.963044] usbhid: USB HID core driver [ 169.650117] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 169.948904] usbcore: registered new interface driver rt2870 after the last kernel update with apt-get update in 2016-06-08 which include these updates: Start-Date: 2016-06-08 10:31:45 Commandline: apt-get upgrade Upgrade: linux-jessie-root-orangepih3:armhf (5.10, 5.11), libavdevice53:armhf (0.8.17-2+rpi1, 0.8.17-2+rpi1+deb7u1), f…